SLS Audio PLS8695 Speaker User Manual
Contents
1. High Pass Filter in disabled out enabled The PLS8695 is equipped with an 80Hz 2nd order Butterworth high pass filter for use in applications having a subwoofer or for restricting the low frequencies in speech only systems The filter may be enabled or disabled by using the 80Hz HPF switch located on the back panel Rev 512 1650 W Jackson Ozark MO 65721 417 883 4549 PLS8695 True Line Source Array Owner s Manual 3 8 Status Indicators CLIP indicates when Channel 1 is clipping PROT indicates when the power supply protective circuitry has been engaged It may be necessary to cycle the power to reset the protective circuitry PWR indicates that power is present in the amplifier SIG indicates that signal is present at the input of the amplifier 3 9 Programming Port This port is used by SLS to program the EEPROM for DSP processing data It requires a proprietary interface and is not user assessable 3 10 Programming Selection This switch allows the selection between two different EQ settings stored in EEPROM Pushed in is optimized for a single PLS8695 Pushed out is optimized for two PLS8695s stacked on top of each other This is boot up enabled so in order to make the EQ change power off the PLS8695 select the button position desired and re power It will boot up with the selected EQ programming 3 11 Mute Switches in signal passes out muted These switches mute the individual amplif2. PLS8695 Powered True Line Source Array Owner s Manual v LL b v gt V O Z Z Lu m 2 l X O X Lu A V NED REDEF I IT Y CLAR O AUD 1650 W Jackson Ozark MO 65721 417 883 4549 512 Rev PLS8695 True Line Source Array Owner s Manual 1 Important Safety Instructions 1 1 CAUTION A A To reduce the risk of electric shock do not remove the back panel of the PLS8695 There are no user serviceable parts inside Refer servicing to SLS Loudspeakers or qualified personnel 1 2 General Safety 1 2 1 Read and follow all warnings operating and safety instructions in this manual and on the unit 1 2 2 Do not use the PLS8695 near bathtubs sinks swimming pools or other locations where water is present 1 2 3 The speakers should be positioned firmly on a level surface Make sure that the supporting object can handle the load weight of the PLS8695 1 2 4 The line voltage selection switch must be set for the correct AC voltage present in the region of use 115VAC or 230VAC Operating the speaker outside these voltages or opposite of the selector switch setting may damage the electronics 1 2 5 For continued protection against risk of fire replace only with same type of fuse and rating for operational voltage selection 1 2 6 Do not place the PLS8695 near heat sources such as stoves heat registers radiators or other appliances that produce heat 1 2 7 Power supply cord
3. able connector is a Neutrik NAC3FCB Up to 2 PLS8695 s can be used on a single 20 amp circuit 3 4 Audio Connection The PLS8695 accepts a balanced audio signal at the XLR audio input connector located on the back panel Pin 3 is high signal The input is transformer balanced with an input impedance of 15K Ohms Connect an appropriate XLR cable between an audio source mixer processor etc to the balanced input connector Unbalanced connec tions can be accomplished by grounding pin 2 or 3 of the XLR audio input connector through the use of an appropri ate adapter or cable A buffered loop output is provided for additional PLS8695s and or active subwoofers 3 5 Power Connection Prior to connecting the power cord and turning on the amplifier always verify the line voltage selection switch is set for the correct AC voltage present in the region of use The PLS8695 is designed to operate on either 115VAC or 230VAC by using the line voltage selection switch Damage may occur to the electronics if the speaker is powered up with the line voltage selector switch in the incorrect position Once set to the proper range the amplifier will regulate the internal voltages so that output power does not change with supply voltage 3 6 Audio Level Control The PLS8695 is equipped with a detented audio level control for use in setting the overall audio level Set this control to the desired position based upon the nominal gain structure desired 3 7 80Hz
4. ier channels for setup and troubleshooting purposes Buttons are reversed from typical settings to protect them from damage when they are in typical positions 4 Specifications Input Sensitivity 1 88V RMS Max SPL calculated 1 Meter 130dB peak Amplifier Power High Freq 500 Watts Amplifier Power Low Freq 1000 Watts AC Power Consumption 11 amps at full rated output Transducers High Freq 9 x PRD500 Ribbons Low Freq 8x 6 5 Woofers 55 5 141cm H Dimensions 11 5 29 2cm W 12 30 5cm D Weight 110lbs 50kg Rugged weather resistant latex Enclosure paint in black white or paintable natural birch Rev 512 1650 W Jackson Ozark MO 65721 417 883 4549
5. nvert box and contents Step 2 Lift the carton carefully clear of inner contents Note do not cut through carton with sharp objects as you might damage cabinet finish We suggest you retain the packaging for possible future use Rev 512 1650 W Jackson Ozark MO 65721 417 883 4549 PLS8695 True Line Source Array Owner s Manual 3 General Use and Operation 3 1 Back Panel Note 3 8 Note 3 8 Note 3 8 Shae ye yan Note 3 8 5 H I 20 VOLUME Note 3 6 ke A Note 3 11 mae 7 2 Note 3 4 Note 3 11 e PGM SEL 3 Note 3 10 eB Note 3 4 Note 3 9 Note 3 7 Rev 512 1650 W Jackson Ozark MO 65721 417 883 4549 PLS8695 True Line Source Array Owner s Manual 3 2 Positioning The PLS8695 has a very defined vertical dispersion which helps prevent interaction with the floor and ceiling and extends the nearfield listening area It is important to set the speaker so the bottom of the box is approximately at chest height of the first listeners The speaker may be tilted for proper positioning relative to the coverage area It is highly recommended that our free LASS aiming software be used to set the position and angle of the PLS8695 s 3 3 AC Mains Connection The AC mains power cord is connected to the front panel through the blue Neutrik Powercon The mating cable end connector is a Neutrik NAC3FCA The grey Powercon connector is a power outlet that allows looping to adjacent PLS8695 s The looping outlet mating c
6. s should be placed so that they will not be pinched by objects being placed on or against them 1 2 8 During extended periods of non use the power cord should be unplugged from the outlet 1 2 9 Do not expose the PLS8695 to rain or moisture Fire or electrical shock may result 1 3 Compliance This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Rev 512 1650 W Jackson Ozark MO 65721 417 883 4549 PLS8695 True Line Source Array Owners Manual AUDIO 2 Introduction 2 1 Welcome to SLS Thank you for choosing SLS Loudspeakers SLS Loudspeakers is a leader in digital amplification and ribbon technology allowing for a new level of sound reproduction clarity and definition Should you need to contact SLS you can visit our website at www slsaudio com or contact our headquarters SLS Loudspeakers 1650 W Jackson Ozark MO 65721 417 883 4549 2 2 Proprietary Technology Various technologies and components within the PLS8695 are proprietary to SLS and protected under letters patent 2 3 Unpacking The PLS8695 loudspeakers are individually shipped in heavy duty cardboard boxes and are protected inside by foam packing material Step 1 Cut sealing tape on bottom or top end fold the carton flaps back and i
Download Pdf Manuals
Related Search