Skyworth LCD-32L16 Flat Panel Television User Manual
Contents
1. ot Connect the other endof this cable to your HDdevice e gt Device HDMI Features e Up to 200 programme memory e Twin Scart connections e Programme swapping e Sleep timer e 4 3 Z00m1 Z00m2 panorama and Full screen picture modes e When no TV signal is dectected after 5 minutes the TV switches itself automatically to stand bymode CYS PAL NTSC e SYS DK I M e HDMI Input supportup to 1080i e PC Input support up to 1080i e PIP e NICAM Stereo AV Stereo Panel Features e High resolution 1366x768 32 TFT LCD display e Brightness 450cd m e High speed response time lt 8msec e 8 bit color depth display 16 7M colors e High contrast ratio 850 1 Typital e Viewing angle 170 H 170 V CR gt 10 In The Box You should have e Television e SCART to RCA jack video connector e Remote control e User Guide e Warranty Card e 2 AAA battery e Stand e Wall mount Installation Install Display on solid horizontal surface such as a table or desk For ventilation leave a space of at least 10 cm free all around the set To prevent any fault and unsafe situations please do not place any objects on top of the set This apparatus can be used in tropical and or moderate climates e Locate the receiver in the room where direct light does not strike the screen Total darkness or a reflection on the picture screen can ca2. Skyworth Model LCD 32L16 User Guide 32 LCD Colour Television 6 Avoid dusty places since accumulated dust inside the chassis may cause failure of the TV when high humidity persists eDo not use this TV near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement etc 6 Never cover the slots or openings of the TV with cloth or other material Never block the bottom ventilation slots of the TV by placing it on a bed sofa rug etc 6 Never place the TV near or over a radiator or heat register 6 Never place the TV in a built in enclosure unless proper ventilation is provided 6776 TV shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the TV SAFETY PRECAUTIONS MAINTENANCE e When the power cord or plug is damaged or frayed unplug this TV from the wall outlet and refer servicing to qualified service personnel e Do not overload wall outlets and extension cords as this can result in fire or electric shock 6 Do not allow anything to rest on or roll over the power cord and do not place the TV where the power cord is subjectto traffic orabuse This may result in a shock or fire hazard e If the TV has been dropped or the cabinet has been damaged unplug this TV from the wall outlet and refer servicing to qualified service pers
3. button on the remote control Picture menu 11 Teletext OPTION Teletext is an information system that dis plays text on the TV screen Using the Tele text information system you can view a page of information on a subject that is available in the list of contents index On screen display is not available in text mode Contrast brightness or colour control is not available but volume control is available in text mode To operate Teletext e Select a TV station on which Teletext is being transmitted e Press Text button Usually the list of contents index is displayed on the screen To select a page of Teletext e Press the appropriate digit buttons for the required Teletext page number The selected page number is displayed at the top left corner of the screen The Teletext page counter searches until the selected page number is located so that the desired page is displayed on the screen e Press PROG button to move the Teletext screen forward one page at a time e Press PROG button to move the Teletext screen backward one page at a time To Select Index Page To select the page number of the index gen erally page 100 press MIX button To mix Teletext with a TV Programme e Press MIX button The text is now super imposed over the programme on the screen e Press MIX button again to return to the Teletext page
4. 4 3 Zoom 1 Zoom 2 Panorama Full Screen Remote control functions 1 POWER STAND BY BUTTON Press this button to turn the TV on stand by 2 SLEEP BUTTON Press this button to set the sleep timer When the preset length of time has passed the TV set Enters standby mode The sleep timer values are follows off 15 30 60 90 120 3 SOUND SYSTEM BUTTON SS Set the correct sound system in TV mode Such as DK I M by pressing this key 4 PERSONAL PRESETS BUTTON PP You can set the picture mode in User Standard Soft Bright mode by pressing this button 5 QUICK VIEW BUTTON Q VIEW This button toggles between the current programme and the previously watched programme Pressing VIEW swaps between the two last watched programmes 6 MUTE BUTTON X Press once to mute the sound press again to return to preset sound level 7 STEREO BILINGUAL SOUND 1 1 BUTTON OPTION When stereo programis received press this button to select STEREOor MONO When bilingual program is received press this button toselect NICAM DUAL 1 NICAM DUAL 2 NICAMMONO 8 DISPLAY BUTTON Press this button to display the program information on the screen e g Channel number for TV input sound mode colour system 9 HOT KEY OPTION The four buttons are provided asa quick wayto enter some pages 10 11 V V BUTTONS Press VOL VOL Buttons toadjust sound level Or adjustthe volume ofeach item inthe me
5. Equalizer A tone control system designed to compensate for frequency distortionin audio systems Enter Equalizer you can select 120HZ 500HZ 1 5KHZ 5KHZ and 10KHZitems by pressing PROG PROG Buttons and changethe correspondingvalue of volume by pressing VOL VOL Buttons Tuner menu Followed by the Tuner menu Program Colour System Sound System Auto Tune Tuning Fine Tune Prog Sort and Skip are the items which can be selected by pressing PROG PROG buttons Program Using the VOL VOL buttons change program you expect Colour System Press the buttonto select anew colour standard value in TV The Choices are AUTO NTSC PAL MENU BUTTON 1 Press menu button to display menu and press VOL or VOL to select sub menu PICTURE Menu p SOUND Menu TUNER Menu FUNCTION Menu Menu button has two functions First is opening or slosing the menu and the second is colsing the current menu and then opening the previous menu The menu will time out automatically after several seconds it is left the screen Press the MENU key on the remote control unit to cancel the menu function 2 After entering an item you can select the desired adjusting item by the VOL VOL buttons and adjust It by the PROG PROG buttons Picture menu Enter Picture menu you can select Brightness Contr
6. HDMI Input Resolutions PIP menu In the Pil menu the external sources thatcan be used source are TVAV SCART 1 SCART 2 S Video HDMI Input typical display modes The following table is an illustration of some of the typical video display modes 640X480 recommend 60Hz 800X600 recommend 60Hz 1024X768 recommend 60Hz 480p 576p 720p 50 60Hz 1080i 50 60Hz N O OI O N YPb Pr Mode Component input The menu of YPb Pr modeis exactly sameas the menu of HDMI mode YPbPr Input typicaldisplay modes The following tableis an illustrationof some ofthe typical video display modes 480i 480p 576i 576p 720p 50 60Hz O 01 OO IN gt 1080i 50 60Hz e Press PROG button to move the Teletext screen forward one page 81 a time e Press PROG button to move the Teletext screen backward one page at a time For Fastext The subject heading for the information may have a particular colour e Press an appropriate Red Green Yellow or Blue button in order to reach the relevant page quickly To CanceI TEXT Press CANCEL button to clear the TEXT But the pagenumber is still displayed on theleft top ofthe screen NOTICE However Teletextis playing all the sameon the backgroundat the time Press CANCEL button againto resume the TEXT ToFreeze TEXT Press HOLD button to hold a Te
7. to qualified per sonnel Do not remove cover as this may re sult in electric shock 8 Naked Flame Sources Do not place naked flame sources on the TV Precautions when using batteries e Do not useold and newbatteries together e Do not usedifferent types ofbatteries for example Manganese andAlkaline batteries together e Note that there arechargeable and non chargeable batteries Do notattempt to charge non chargeable batteries e Remove the batteries fromthe remote control unit if you donot intend touse the unitfor a long time NOTE e Do not dropthe remote control unit e Do not subjectthe remote control unit to physical shocks e Keep the remotecontrol unit dry Wetting itmay cause the unit tomalfunction Replace the batteries with new ones when operation of the unit deteriorates Switching the TV ON OFF To switch the TV on Connect the main cable to the power input socket Press on off switch at the rear of the TV The TV switches itself and the LED indicator on the front of the TV change from red to green color quickly To switch the TV off Press the button on the remote control or TV the TV will switch to stand by mode and the GREEN LED Operating the TV TUNINGIN THE TV CHANNELS Make sure that all connections including the TV aerial have been made before turning on the TV Before Switching on the TV Power connection IMPORTANT This TV set is designed to
8. 2 D S gt 11 Installation 11 MENU in PC Mode T 11 Picture menu n 11 Sound menu 11 Adjust menu 11 Function menu 11 PIP menu 11 HDMI Input Resolutions 12 PIP menu 12 LOCI ee 12 To operate Teletext n 12 To select a page of Teletext 12 To Select Index Page 12 To mix Teletext with a TV Programme 12 To Select Double Height Text T 13 To Reveal concealed Information 13 To Stop Automatic Page Change 13 4 5 OO CPOO TTT 2 Remote Control Buttons Power Sleep an e an Q View Mute Ba Rec A CONG 1 D Power 2 Sleep Sleep Button 3 SS Sound System Button 4 PP Picture Mode 5 Q View Quick V iew 6 Mute I II Sound Mode Selection Display Screen Display 9 Hot Key only in teletext mode V Volume Up 11 v Volume Down 12 P Program Up 13 P Program Down 4 menu 6 5 0 9 Digit Button aviv AD TxT Text 18 sub page Reveal 20 index 21 mix 22 Cancel 03 Hold 24 Size The following page will show the remote control functions 29 14 MENU BUTTON MENU Press this button to enter the menu mode for various Optional adjustable settings To lo
9. OG buttons Notice Only after finishing auto tune channels will be sorted If you breakthe process duringthe auto tune period channelswill be searchedand stored however the channel willnot be sorted into their correct channel order Manual Tuning 1 Press Menu button 2 Press Vol or button repeatedly untilthe TUNER icon is highlighted 3 Press the PROG button andhighlight Program and change the Channelnumber showing tothe number that you wishto store orchange the TV station showing by pressing Vol button 4 Press Prog button repeatedly and highlight MANUAL TUNE 5 Start the manual tuning processby pressing the VOL or VOL button 6 When thedesired TV stationis showing pressthe MENU button toreturn the TVto its normal operation The TV stationwill be automatically stored into the channel number thatwas previously inputted 7 To store furtherchannel repeat abovesteps but this time change thechannel number instep 3 toyour next desired stored channelnumber 2 3 etc Fine Tune Press VOL VOL button to adjustthe little change offrequency 3 lt a art a10 Sound menu 2 4 k Adjust menu Using PROG PROG toselect different items press VOL VOL to set different values in Frequency phase H position and V position When you selectAuto adjust pressing VOL to adjust dif
10. Turkey Austria Belgium Switzerland Czech Germany Denmark Spain France Finland Notice Different countrieswill effect the sort process in AUTOTUNE Factory Reset Option Press VOL key to deleteall previously stored program information PIP menu oB The last Menuis PIP menu youcan select Mode PIP H POS PIP V POS Brightness Contrast Sub Source and Swapitems by pressing PRGO Buttons Mode The choices arePIP and Off Only bychoosing PIP you can enterPIP H POS PIP V POS Brightness Contrast Sub Source and Swap items PIP H POS Press the buttonto change horizontal position PIP V POS Press the buttonto change vertical positon Note PIP Pictureln Picture isused to display an external source suchas HDMI VGA YPbPr boxat same time asdisplaying the TVchannel that you are watching Sound System Press the buttonto select anew sound standard value inTV The options are DK I M NOTE This TV factory setto I UKsound If changed to another setting whilstreceiving a UK TV station this will result in lossof sound Change back to I to restore the sound AUTO Tune 1 Press MENU button 2 Press VOL button and highlightthe TUNING icon 3 Press PROG button andhighlight AUTOTUNE 4 Press VOL button to startthe automatic tuning process 5 Aftera few minutes the tuning willend and the first station stored will show onthe TV screen 6 Change channels by pressing the PROG PR
11. U LEAVE YOUR HOUSE The LCD panel is a high technology prod uct with about a million thin film transis tors giving fine picture details Occasion ally a few non active pixels may appear on the screen as a fixed point of blue green or red Please note that this does not af fect the performance of the product Safety Precautions 1 Power Source This TV should be operated only from a 100 240V AC 50 60Hz supply 2 Power Cord The power supply cord should be placeq such that it is not likely to be walked on or pinched by items placed upon them or against it Pay particular attention to cord where it enters the plug power outlet and the point where it exits from the TV 3 Moisture and Water Do not use this equipment in humid or damp places avoid the bathroom the sink in the kitchen and near the washing ma chine Do not expose this TV to rain or wa ter as this may be dangerous 4 Cleaning Before cleaning unplug the mains cable from the household supply Do not use liq uid or aerosol cleaners Only use a soft dry cloth 5 Ventilation The slots and openings on the TV are in tended for ventilation and to ensure reliable operation To prevent overheating these openings must not be blocked or covered in anyway 6 Lightning In case of storm or lightning or when going on holiday disconnect the power cord and aerial lead from the wall outlet 7 Servicing Please refer all servicing
12. ast Colour Sharpness Colour Temp and N R items by pressing PRGO or PROG buttons Brightness Using the VOL VOL button lighten darken the picture Contrast Press the VOL VOL key to enhance reduce the contrast of the picture Colour Press the VOL VOL button to increase decrease the colour saturation Sharpness Utilize the button to sharpen or soften the picture Colour Temp Make use of the button to select a suitable colour temperature to display The choices are Normal Cooler Cool Warm Warmer N R Press the button to adjust noise reduction The options are Off Low Middle High Prog Sort Press Vol to enter User can setthe two channelnumbers that want to swap inprogram 1 andprogram 2 selectthe swap item press Vol button toperform swapping SKIP press the skipto enable ordisable the current program being tunedby pressing Vol or Vol buttons the choiceare on and off Function menu f 1 lt A nu 1 guage Engli ang In the Function Menu OSD languagesand APS related options are displayed on the screen Menu Language The Language is English and Chinese Txt Language Option The teletext languageis UK East Euro Greece Cyrillic Arabic Country Option Select your location country UK Greece Hungary Italy Norway Netherlands portugal Poland Sweden Slovenia Slovakia
13. ferent pitcturemodes automatically Function menu BORE PIP menu BOR EW In PC modes the sub sourceoptions are TV AV SCART 1 SCART 2 S VIDEO which are defferent from TV mode PC Inputtypical display modes The following tableis an illustrationof some ofthe typical video display modes 1 640X480 recommend 60Hz 2 800X600 recommend 60Hz 3 1024X768 recommend 60Hz 4 480p 50 6 720p 50 60Hz 7 1080i 50 60Hz Brightness Press the VOL VOL button to lighten darken the picturein PIP state Contrast Press the VOL VOL button to increase decrease the contrastof the picturein PIP state Sub Source The choices are VGA HDMI YPbPr Swap Press VOL button to swap the picture between PIP and TV state PC MODE Installation Power off both Computer and Display before making any connections e The monitor comes with a15 pin PC socket Connect the end of signalcable to the socket of the TVand connect the other end to the 15 pin connectorto the computer 15 Pin MiniD Sub Connector e Tighten the screws of the Display cable until the connectors are fastened securely at both ends finger tighten only f you are using Windows operating system running on a PC with a Microsoft Plug amp Play compatible video card your system will se lect the appropriate timing for your monitor MENU inPC Mode Enter menu bypressing the MENU
14. nu status 12 13 P P BUTTONS Press PROG Or PROG button to selectthe program forwards orbackwards Location of controls J HALF SCART FULL SCART d 92 00 5 1 ON OFF Switch 2 Power Indicator 3 Remote Sensor 4 IV AV 5 MENU 6 VOL Button 7 VOL Button 8 PROG Button 9 PROG Button 10 Speakers 11 FULL SCART 12 HALF SCART 13 HDMI Input 14 VGA Input 15 Y Pb Cb Pr Cr 16 AUDIO IN L 17 AUDIO R 18 Aerial input socket 19 Power cord input 20 S Video 21 Video input 22 Audio input Left amp Right 8 Note Fullscart is fullywired for Inoutand output andshould be usedfor connections of VCR 4 Half Scart hasis wired only tothe TV andcan be usedfor playback onlysuch as Freeview Skybox qndother external input sources only eIMPORTANTINFORMATION Power offboth HD playerand display beforemaking any connections Connect thesupplied HDMI cableto the HDMIsocket ofthe TV connect the other end tothe HDMI outputsocket ofthe HD playersource eConnect the HDMIcable to the HDMI socket of the TV Connect theother end tothe HDMI output socketof the HD player source HDMI cable will carry both Video andaudio signals FULL SCART HALF SCART from the HD source to the TV Connect the HDMIcable to the HDMI input on the TV
15. ok for more information Please turn to page 9 15 PROGRAMSELECTION BUTTONS 0 9 Use 0 9 digit buttons you can directly call one or two digits program number that you want Press after the screen display or You can press digit number button directly to select two three digit numbers In CATV system if you want to watch the channel from 100 to 125 such as channel 123 please press first and press 2 and 3 inturn 16 AV TV BUTTON Press this button to display external video signal such as SCART1 SCART2 AWS VIDEO YPbPr VGA HDMI TV Using PROG PROG Button select item and 17 TXT BUTTON OPTION This button is used for entering the teletext MENU 18 SUB PAGE BUTTON OPTION Subcode mode gives the possibility to select certain subcode pages of a teletext page 19 REVEAL BUTTON OPTION Press this button to reveal the hidden information for so me Teletext pages press again to hide the information 20 INDEX BUTTON OPTION Press this button to enter the Teletext s index MENU 21 MIX BUTTON OPTION the button is used as closing opening the teletext background 22 CANCEL BUTTON OPTION Press this button to appear the TV signal on the background 23 HOLD BUTTON OPTION Press this button to hold the Teletext page no display to prevent the page from changing Press again to release the hold state 24 SIZE BUTTON Press this button you can select differentimage sizes
16. onnel 6 Never push objects of any kind into this TV through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock 6 Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage Refer all servicing to qualified service personnel e Do not place this TV on an unstable cart stand or table The TV may fall causing serious injury to human and serious damage to the appliance SAFETY PRECAUTIONS MAINTENANCE elfa strange sound or smell gives off from the TV please turn off and unplug it from the wall outlet then refer to service personnel artificial or sunlight does not shine directly on the screen If the TV does not work properly and you are unable to restore normal operation by following the ITROUBLESHOOTING section in your instruction manual do not attempt any further adjustment Unplug the TV and consult service personnel 6 To prevent fire never place any type of candle or nakeq flames on the top or near the TV e Avoid any kind of impact to the TV Be special careful not to damage the screen face Adjust only those controls that are covered in the instruction manual as improper adjustment of other controls may result in damage please ask your service personnel to restore the TV to normal operation For added protection for this TV during a lightning
17. op erate on 100 240V AC 50 60Hz only e After unpacking allow the TV set to reach the ambient room temperature before connect ing the set to the mains e The mains plugis used asthe disconnect device the mains plugshall remain readily operable Connections to the Aerial input socket TV Aerial inputsocket e Connect the aerial plug to the aerial input socket located at the back of the TV How to connect other devices IMPORTANT Switch off the TV before con necting any external device Sockets for external connections are at the rear and underside of the TV For connection of other devices via Scart refer to the manu als of the related devices Inserting batteries in the remote control handset e Remove the battery cover located on the back of the handset by gently pulling up wards from the indicated part e Insert two AAA R03 Alkaline or equivalent batteries Following the marking inthe battery compartment e Replace the battery cover Sound menu Enter Sound menu youcan select Volume Balance Surround MSS and Equalizer items by pressing PRGO PROG Buttons Volume Press the VOL 7 01 button to adjust the sound volume Balance Choose the VOL VOL button to adjust to the leftto right soundchannel volume Surround Press the keyto select surround mode on off MSS Press the buttonto get bassor treble The choice areon and off
18. storm unplug it from the wall outlet and disconnect the antenna or cable system 6 f the TV is to remain unused for a period of time turn off and unplug it from the wall outlet lt i e Choose a place where light 2 To Select a Sub i G s ms Ts sua POF PASTO sam Cancel TEXT To Freeze TEXT To exit Teletext Service Tips Contents Remote Control Buttons 2 Remote Control functions 3 Location of controls 4 HDMI Cable Connections 5 Installation 6 K I s aa aa 6 Panel 6 00 6 Safety Precautions 7 Before Switching On The TV 8 Power Connection 8 Connections To The Aerial Input Socket 8 How To Connect Other Devices 8 Inserting Batteries In The Remote Control Handset 8 Precautions When Using Batteries F 8 Switching the TV ON OFF 8 To switch the TV on F 8 To switch the TV off 8 Operating the TV 8 MENU BUTTON 9 Picture menu 9 Sound menu 9 Tuner menu 9 Function menu 10 PIP menu gt n 10 PO MODE 2 2 22 2 22
19. ted page is found Fastext This TV supports a 500 page Teletext system When the page number of any of the 7 pages in memory is entered the system will not search for the requested page instead it will display the page automatically 14 On Screen Display Control outside the screen i s Cc O O O oO oO uw O ao 0 oO Q O 2 gt 5 5 O O O Z O O O A Q T D gt Ke 0 5 QA 0 0 O N O L A oO Cc lt O oO O ep O S Q oO O 0 x 0 2 D O oO O Q Double image Lines in picture Weak picture Blurred picture BLE gt lt O Cc O 0 0 2 2 Q O 0 oO xX O 0 2 Q O Ke 5 60 5 5 O 9 0 Z 0 WY 5 O 0 z Symptoms ON SYMPTOMS AND SOLUTIONS BEFORE CALLING FOR SERVICE HAVE YOU CHECKED THE FOLLOWING CHART Service Tips
20. use eyestrain Soft and indirect lighting is recommended for comfortable viewing e Allow enough space between the receiver and the wall to permit ventilation e Avoid excessively warm locations to prevent possible damage to the cabinet or premature componenttfailure This TV operates on AC supply directly connect the AC plug to the socket at the back of the TV Insert the mains plug in the socket having a mains voltage of 100 240V AC 6 Do not install the receiver in a location near heat sources such as radiator air ducts direct sunlight or in a place somewhere like close compartment and close area Do not cover the ventilation openings when using WARNING When the device is not in use for a long periods disconnect from power Instructions for waste disposal e Packaging and packaging aids are recy clable and should principally be recycled Packaging matenals such as foil bag must be kept away from children e Battery including those which is heavy metal free should not be disposed of with household waste Please dispose of used battery in an environmentally sound man ner Find out about the legal regulations which apply in your area e Cold cathode fluoresant lamp in LCD PANEL contains a small amount of mercury please follow local ordinates or regulations for dis posal yx NS we N yy S K MANRO wS IIN Uy TINS DO NOT LEAVE YOUR TV IN STAND BY OR ON WHEN YO
21. xt page This means thepage will not change and refresh Press the buttonagain to releasethe hold state To exit Teletext Press the TEXT button The screen will switch to TV mode To Select Double Height Text Press SIZE button for the top half of the in formation page to be displayed in double height text e Press SIZE button again for the bottom half of the information page to be displayed in double height text e Press SIZE button once more for the full page of normal height text To Reveal concealed Information e Pressing REVEAL button once will reveal answers on a quiz or games page e Pressing REVEAL button again will conceal the revealed answers To Stop Automatic Page Change The teletext page selected may contain more information than that shown on the screen the rest of the information will be displayed after a period of time To Select a Subcode Page Subcode pages are subsections of long Teletext pages that can only be displayed on the screen one section at a time e Select the required Teletext page e Press SUB PAGE button e Select the required subcode page number by pressing four digit buttons e g 0001 e If the selected subcode page is not displayed in a short time press SUB PAGE button TV programme will be displayed on the screen e Teletext page number will be displayed on the upper left corner of the screen when the selec
Download Pdf Manuals
Related Search