Scytek electronic G40RS Remote Starter User Manual
Contents
1. E LEGTRONII GALAXY G40RS AUTOMATIC TRANSMISSION ONLY WITH SEPERATE LOCK UNLOCK BUTTONS REMOTE START SYSTEM PRODUCT MANUAL limiecliednoerrene This vehicle remote start svstem is warranted to the original purchaser to be free from defects in material and workmanship The manufacturer will repair or replace at its option and free of charge for the first twelve 12 months anv part that proves defective in material or workmanship under normal installation use and service provided the product is returned to the manufacturer freight prepaid After the first 12 month warrantv period there will be a maximum service charge of 25 00 per calendar vear if required for repair and or replacement of anv defective parts A copv of the original purchase and installation receipt must accompanv anv products returned for warrantv service Warrantv is limited to defective parts and or replacement parts only and excludes any incidental and consequential damages connected therewith WARRANTY OF INSTALLATION LABOR REMOVAL AND RE INSTALLATION CHARGES ARE NOT THE RESPONSIBILITV OF THE MANUFACTURER Note This Warrantv is voided if the product was not installed bv an Authorized ScvTek Dealer FCC ID OARRXAM2000 This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept anv interference received including interfe2. System Programming parameters are now set to factory default settings The Valet Mode is off Page 6 G 40RS XIX PERS AMIN 3 Door Unlock Pulse Single Double 6 Lock after Shutdown On Off 9 Tachless Sense Crank Time Normal Extended Super Extended 12 Unlock Before Start Disabled Enabled 13 Horn Chirp Enabled Disabled 14 Smart Start Run Monitor Enabled Disabled 15 Trunk Release Horn Out Trunk Release Horn Output Jumper Selection Carefully separate the top and bottom halves of the main unit case Once the cover is removed the parking light polarity jumper will be visible next to the parking light relay Set the jumper for the correct polarity output as described below then reassemble the main unit case Parking Light Output Selects the polarity for the output of the on board Parking Light relay Left Pin Center Pin positive Right Pin Center Pin negative default setting shown 40RS Page 7 System Installation 8 Pin Main Harness Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 RED WIRE Module Power Input Connect to a constant source of 12V GREEN WHITE WIRE Brake Input Connect to the wire that shows 12V when pressing the brake The Green white wire is a safety shutdown wire that must be connected BROWN WHITE Horn Output 500 mA Connect to a relay to activate the vehicle s horn when the alarm is triggered This wire may instead be programmed as an ig
3. ever Install G40RS in vehicles equipped with MANUAL TRANSMISSION DO NOT remote start the vehicle in a closed garage Make sure that the garage door is open or there is adequate ventilation Failure to observe this rule could result in injury or death from poisonous Carbon To ensure the safety and security of the system while it is remote started the G40RS Starter employs several safeguards In the event the brake pedal is pressed while the engine is remotely running the remote start will immediately shutdown to prevent unauthorized users from attempting to drive the vehicle The system is equipped with a hood pin input to prevent access to the engine compartment while the vehicle is remotely running Finally the Valet Mode prevents the remote start feature from operating in the event the vehicle is to be serviced Button 1 Locks the doors and when held for 5 seconds activates the system s Car locator feature Button 2 Unlocks the doors Button 3 Feature programming only Button 4 Activates and deactivates the Remote Start feature 2 40RS Adding Replacing Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system have all desired transmitters ready and follow the steps below Note Up to four transmitters can be programmed to operate the system To erase any previously stored transmitter codes be sure to program all 4 transmitter memory locations To program transmitter s 1 Turn
4. the ignition key On Off On Off and back On The parking lights will flash 3 times 2 Press and hold the Override switch for 5 seconds The parking lights will flash 5 times The LED will illuminate 3 Press Button 1 on the first transmitter The parking lights will flash once 4 Repeat steps 3 and for each transmitter up to 4 5 Turn off the ignition key The parking lights will flash 3 times 40RS Page 3 System Operation Remote Locking To Lock the doors 1 Turn off the ignition 2 Press Button 1 The doors will lock The parking lights will flash once The LED will turn on to indicate the doors are locked 3 10 seconds after Locking The LED will start blinking Remote Unlocking To Unlock the doors Press Button 2 The doors will unlock The parking lights will flash twice The LED will turn off Remote Starting Automatic Transmission Mode To Remote Start the System 1 Be sure the system is not in Valet Mode 2 Press and hold Button 4 The parking lights will flash twice The doors will lock programmable The engine will start and run for the duration of its programmed Run Time The heater or air conditioner will turn on if turned on prior to exiting the vehicle To resume control of the vehicle 1 Unlock the doors manually or with the Transmitter 2 Turn on the ignition 3 Press the Brake Pedal to disengage the remote start Visual Car Locator Mode Use t
5. his feature to locate your vehicle in a crowded parking lot Look for the flashing parking lights which should be your vehicle To activate the Visual Car Locator Mode 1 Press and hold Button 1 for 3 seconds The parking lights will flash The doors will unlock allowing access to the vehicle 2 Press Button 2 to turn off Car Finder Page 4 40RS Valet Mode The Valet Mode temporarily disables the remote start system so the vehicle may be serviced by a mechanic The remote transmitters will continue to lock unlock the doors To activate or deactivate the Valet Mode 1 Turn on the ignition 2 Press and hold the override switch for 5 seconds The parking lights will flash once and LED will be On to confirm the Valet Mode is on or twice and LED will turn off to confirm Valet Mode is off 3 Turn off the ignition Shut Down When the the Remote Start feature is active any of the following actions will shutdown the engine 1 Pressing Button 4 After the engine shuts down the doors will lock programmable 2 Pressing the Brake Pedal 3 Opening the Hood 4 Remote Start Time Out completion of the timed run cycle Quick Stop Automatic Transmission Only The Quick Stop Feature allows you to exit the vehicle while keeping the engine running for quick stops To leave the vehicle running 1 Press Button 4 2 The parking lights will turn on Now turn the ignition key off and the vehicle will continue to run 3 Y
6. nition 3 relay trigger WHITE WIRE Parking Light Output relay Connect the White wire to the circuit that shows 12V or ground only when the parking lights are on and set the internal parking light relay jumper to the proper polarity For parking light circuits exceeding 10 amps a relay is required For vehicle s with independent left and right parking light circuits diodes must be installed to keep the circuits separate NOTE Do not connect the WHITE wire to the vehicle s headlight circuit WHITE BLACK WIRE Hood Pin Input Connect the to the hood pin switch The switch must provide a ground output when switch is opened BLUE ORANGE WIRE Ground When Running Output 500 mA Connect to an optional factory security bypass module if required BLACK WIRE Ground Input The Black wire must connect to a solid chassis ground Clean away any paint or dirt to insure the best possible ground BLACK GRAY WIRE Tach Input Connect to the vehicle s tach wire or a fuel injector wire if the tachless mode does not provide satisfactory operation 8 40RS 2 Pin Blue Connector Valet switch port Mount switch where it is accessible from the driver s position 2 Pin Red Connector LED port Mount LED where it may be easily seen from either side of the vehicle 3 Pin White Door Lock Connector Door lock port BLUE WIRE negative unlock output 500mA RED WIRE 100mA trigger output for optional plug in door lock relay m
7. odule GREEN WIRE negative lock output 500mA 5 Pin White Flat Connector Antenna connector port Starter Diagnostics Starter doesn t start and Parking Lights flash 3 Times Hood Trigger is active 4 Times Brake Lights stay On 5 Times Unit is in Valet service mode and start is disabled 40RS Page 9 DOO MHOC CDIAGRANIS Negative Trigger Adding Actuators Green wire Door Unlock wine DOOR LOCK SWITCH Reverse Polarity 15 FUSE DOOR LOCK 12V SWITCH Blue wire FACTORY UNLOCK I MOTOR 12V 30 ees Green wire Parkit LOCK Positive Horn Honk TO POSITIVE HORN WIRE 124 10 4065 Wiring Diagram Violet Starter Output Yellow Ignition 1 Output Orange Accessory Output Brown Ignition 2 Output ACC Starter2 Red 12V Battery Input 1 25 Amp Red 12V Battery Input 2 25 Amp Red 12V Battery Input 3 Green White Brake Input Control U n it Brown White Horn Output 500mA White Parking Light Output built in relay G 40 RS White Black Input Blue Orange Remote Start output When running Black Ground Black Gray Tachometer Input For Factory Disarm pulse use the unlock wire Sid Lock output 500mA mp Blue Unlock output 500mA Enable unlock Before Start location OVERIDE SW IN 12 LED OUT C Antenna System Programming Added Button 1 button 2 15 Tr
8. ou may now exit the vehicle and lock the doors manually or by using the Remote Transmitter To resume control of the vehicle 1 Unlock the doors manually or with the Transmitter 2 Turn on the ignition 3 Press the Brake Pedal to disengage the remote start Automatic Start Mode The Automatic Start Mode allows the vehicle to automatically start the vehicle every one or two hours and run for the preset Run Time automatic start mode must be selected feature 8 To turn on Auto Starting 1 Turn Ignition switch Off and wait for 3 seconds 2 Turn Ignition switch On and Off three times ending with Ignition in Off position 3 Press and release the Valet switch immediatly Parking lights will flash indicating that the Auto Start mode has been activated To turn off Auto Starting do one of the following Turn ignition On Arm and then Disarm the system Alarm or Panic the system Automatic Start Mode will stay active for 24 hours only 40RS Page 5 Ignition Door Locking For added safety the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on Ignition Door Unlocking For added convenience this feature automatically unlocks the doors after the ignition key is turned off The Ignition Door Unlocking feature may also be completely disabled if desired Battery Replacement Your Remote Transmitter uses 2 3 volt batteries type CR2016
9. rence that mav cause undesired operation PLEASE NOTE Some of the features described in this manual mav require additional parts and or labor and mav not be included as part of the standard installation of this unit Additionallv many features of this security system have selectable options that must be activated or programmed during the system s installation These items will be identified in the following sections Please discuss these features and any questions you may have regarding the installation of this product with Your Authorized Dealer 4065 1 REMO FANSANI ars Remote Transmitter Description LED Button 2 Button 4 The G40RS is a state of the art remote starting system is supplied with two 4 button Remote Transmitters used to control system operations The built in remote start feature is designed to offer maximum convenience by remote starting your vehicle s engine turning on the heater air conditioner and then running for a pre determined time to provide a comfortable environment once you enter your vehicle ScyTek Electronics Inc and its VENDORS shall not be liable for any accident resulting from the use of this equipment This system is designed to be professionally installed into a car or vehicle in which all items such as parking brake and all associated components Hood switches transmission shift linkage throttle linkage and all engine safety features are in perfect working condition Do not
10. unk Release Horn Out Trunk Release Horn Output ScyTek Electronics 11627 Cantara Street North Hollywood CA 91605 www scytek net ScyTek Electronics 2009 G 40RS 7 29 09
11. which will require replacement in time Depending on the amount of use the battery may last up to six months or more before it needs replacement When the battery needs replacing the system s operating range will decrease or the transmitter LED may not be as bright In order to change the battery separate the top and bottom halves of the case While replacing the battery make sure that the positive and negative terminals are positioned correctly then carefully reassemble the transmitter case Entering System Programming To enter System Programming 1 Turn on ignition 2 Within 5 seconds press the valet switch 5 times The parking lights will flash three 3 times indicating you have entered Programming 3 Press the valet switch the number times equal to the System Parameter you want to change The parking lights will flash each time the valet switch is pressed 4 Within 5 seconds press the transmitter button corresponding to the desired operating mode for that System Parameter The parking lights will flash to indicate the setting 1 flash Button 1 2 flashes Button 2 3 flashes Button 3 5 When finished turn off the ignition to save the changes Default Reset Following this procedure will set all System Programming Parameters to factory default settings 1 Enter System Programming 2 Press Transmitter Button 3 The parking lights will flash 6 times indicating that the reset signal was received All
Download Pdf Manuals
Related Search