Scytek electronic 777-TC Automobile Alarm User Manual
Contents
1. ae irte pdt aa qp LAT aa Page 19 Silent Armind DISARMING ic wc aed tope cA ace e QV d ede edt a e e ea E o dee eg Page 19 O eee 19 25 95 55 AS a e Mie 20 Emergency Override s 5 asta ee 2 aries eee 20 Optional Coded Emergency Override 2 Page 20 Automatic AA a DESERTI Page 21 Valet MOE 5 3 xe oo enemies A AA a cm t Page 21 e lee CA AAA a aa Page 21 5 EXtenasd opa soari say ngs NA ian ea 22 Fanito Controlled Door LOCKS iid si edidi La idee ei 22 DOME LGNEACHVYation varia Y docet DA eed od Page 22 AUX pa HOO UEDUES ci A AS A AR e e d Page 22 Disarm with Auxiliary Function a A aa ae Page 22 Remote Sensor DISaDIS iaa dob od x uo ara t Page 22 Ant Carjacking Protection AAN AA AAA des Page 22 6 SyStermhsPalldtlOb ante Due aon S ar Aaa AE Page 23 Moning ME Conero unit e A IL Page 24 Moun no Es Es gt il da cea ea allor Page 24 Mounting Me Shock SENSOR sosti e ante Page 24 7 asa ER AI Le PARAS e OR VR i Page 25 SE website venete e opes ta e Page 25 A o d er dome ub ai Ri REN2. To activate the Panic Mode 1 Press and hold Button 1 for 5 seconds The alarm will sound The parking lights will flash The doors will unlock allowing access to the vehicle 2 Press Button 2 to stop Panic Mode fthe ignition is on when the Panic feature is activated the doors will lock for personal safety Emergency Override If the transmitter becomes lost or inoperable the system can still be disarmed using the following procedure Before beginning this procedure be sure to have the ignition key ready and know the location of the override switch To Emergency Override the system 1 Unlock the door using the key 2 Enter the vehicle The system will trigger and the siren will sound 3 Turn the ignition key on 4 Press and hold the override switch until the system disarms 5 he vehicle will now be able to start Optional Coded Emergency Override As an extra measure of security the system is equipped with an optional Coded Emergency Override feature Once an Emergency Override Code is chosen and programmed during installation the system can no longer be disarmed using the standard override procedure To Emergency Override the system using the Code 1 Follow steps 1 3 above 2 Press the override switch a number of times equal to the Disarm code and continue holding for 10 seconds on the last press The system will disarm the code is entered incorrectly turn off the ignition and begin again To s
3. 4 Pin shock sensor harness 3 Pin door lock harness LED harness e Valet Switch harness Receiver Harness Verify with the owner the mounting locations for all visible components including the LED and Override switch Verify with the owner the optional features of the Astra 777 TC and the functions that must be programmed during installation Inspect and perform a function test of all vehicle systems before and after the installation Always use a Volt Ohm meter for testing vehicle circuits Never use a test light Always look before drilling any holes or mounting self tapping screws Be sure fuel lines and exterior wiring looms are clear as they are often close to the chassis and difficult to see Protect all wires running from the engine compartment to the interior of the vehicle by covering with electrical tape and split loom tubing Be sure to use a grommet when routing wires through the firewall Properly fuse any additional accessories such as window modules door lock actuators etc making sure to power them separate from the alarm module This will ensure the functionality of the security system in the event of an accessory failure Astra 777 Page 23 Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle Do not mount the main unit in the engine compartment Choose a mounting location that will not be easily accessible to a thief and will not interfere with the ope
4. E ER R N IC S ASTRA 777 1C WITH TRUE COLOR REMOTE VEHI CLE SECURI TY SYSTEM PRODUCT MANUAL Linnie itetime Warranty This vehicle security system is warranted to the original purchaser to be free from defects in material and workmanship The manufacturer will repair or replace at its option and free of charge for the first twelve 12 months any part that proves defective in material or workmanship under normal installation use and service provided the product is returned to the manufacturer freight prepaid After the first 12 month warranty period there will be a maximum service charge of 25 00 per calendar year if required for repair and or replacement of any defective parts A copy of the original purchase and installation receipt must accompany any products returned for warranty service Warranty is limited to defective parts and or replacement parts only and excludes any incidental and consequential damages connected therewith The manufacturer of this theft deterrent system makes no warranty against the theft of the vehicle or its contents This warranty is not to be construed as an insurance policy against loss WARRANTY OF INSTALLATION LABOR REMOVAL AND RE INSTALLATION CHARGES ARE NOT THE RESPONSIBILITY OF THE MANUFACTURER Note This Warranty is voided if the product was not installed by an Authorized ScyTek Dealer Table of Contents 1 ADOUCY SN ira VIMINALE RR Page 1 2 Remote T
5. if the chirps are disabled SND Sound function allows disabling of the transmitter s confirmation tones To turn the transmitter confirmation tones on or off 1 Press and hold Button 5 until the display shows SND The transmitter will beep four times 2 Release Button 5 transmitter will beep once The LCD panel will beep five times if enabled or vibrate and display off if the confirmation tones are disabled PSV Passive function allows the passive arming mode to be enabled oe disabled with the transmitter Note This feature may not be available on all systems To enable or disable the passive arming mode 1 Press and hold Button 5 until the display shows PSV The transmitter will beep five times 2 Release Button 5 The transmitter will beep once and the system will begin the passive arm mode The LCD panel will display off and vibrate twice if disabled Page 14 Astra 777 TC Valet mode function sets and resets the security system valet mode this function is enabled only when the security system is disarmed Set or reset the Valet mode 1 Press and hold Button 6 until the display shows VLT The transmitter will beep six times 2 Release Button 5 The LCD panel will play a tone if the Valet mode was set V will be displayed indicating that the system is in Valet mode The transmitter will beep twice if the Valet mode was reset V will turn off indicating that the security syste
6. 5 Setting AutoStart Cold Temperature Threshold Select Cold Temp start setting by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it SIREN CHIRP PASSIVE ARM Use buttons 3 amp 4 to scroll up or down to chage the temperature threshold Save the changes by pressing button 5 AUTOSTART SET COLD TEMP TEMP 11 F Security system responce Setting AutoStart Hot Temperature Threshold Select Cold Temp Time setting by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it SIREN CHIRP PASSIVE ARM COLD TEMP Use buttons 3 amp 4 to scroll up or down to chage the temperature threshold Save the changes by pressing button 5 AUTOSTART SET HOT TEMP TEMP 1109 Security system responce Page 6 Astra 777 TC SYNdironiz SYys 22518 ere Gods Select Clock Sync setting by pressing buttons 1 or 2 to highlight the pager Press button 3 to select the pager Pager Clock Sync This feature synchronizes the pager clock to the security system time of a day clock Select Pager Clock Sync by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it PGR CLK SYNC SYS CLK SYNC AUTO CLOCK SET EXIT Security system responce START 1 TIME START 2 TIME System Clock Sync This feature synchronizes the system clock to the pager time of a day clock Select Sytem Clock Sync by pressing buttons
7. BLUE WIRE Trunk Hood trigger Input Connect the BLUE wire to the trunk and or optional hood pin switches The switch must provide a ground output when opened Pin 10 GRAY WIRE Auxiliary 1 Output 500mA Connect to a relay or module for an optional feature such as trunk release etc Pin 11 YELLOW WI RE 12V Ignition Input The YELLOW wire must connect to a main ignition wire at the ignition harness This wire must show 12V when the ignition is on Pin 12 BLACK WI RE Ground Input The BLACK wire must connect to a solid chassis ground Clean away any paint or dirt to insure the best possible ground Pin 13 VIOLET WIRE Positive door trigger Input Connect to the door switch circuit wire that shows 12V when the door is open This type of door circuit is usually found on Ford vehicles Pin 14 GREEN WIRE Negative door trigger Input Connect to the door switch circuit wire that shows ground when the door is open Astra 777 TC Page 25 Plug in Connectors 3 Pin White Door Lock Connector Plug in connector port for door lock harness or optional door lock relay module BLUE WIRE negative unlock output 500mA GREEN WIRE negative lock output 500 2 Pin Red Connector Plug in connector port for LED Mount the LED in an area where it may be easily seen from either side of the vehicle 2 Pin Blue Connector Plug in connector port for valet switch Mount the valet switch in an area that 5 easily accessible
8. Button 5 until the display shows CONFIRM The transmitter will beep once 2 Release Button 5 The transmitter will beep once panel will display the current system status Page 2 Astra 777 TC PAGERTPARAMETERSTSETTING Press and hold Buttons 2 and 3 until pager program features are displayed Select pager setting by pressing buttons 1 or 2 to highlight the pager Press button 3 to select the pager Setting Date amp Time Select Time Date setting by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it Use buttons 1 amp 2 to highlight the parameter you wish to change use buttons 3 amp 4 to scroll up or down to chage the time or date Save the changes by pressing button 5 12 00P TIME 04 12P 11 24 Setting AutoStart Time Select Start Time setting by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it Enable Disable Auto Start Xn Auto Start on off by pressing button 3 Symbol is displayed if the Auto Start feature when enabled START SET AUTO ST ON TIME 08 00 Astra 777 TC Page 3 Use buttons 1 amp 2 to highlight the time parameter you wish to change use buttons 3 amp 4 to scroll up or down to chage the time Save the changes by pressing button 5 START SET AUTO ST ON TIME 08 00 Setting Alarm Clock Select Alarm setting by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it TIME
9. DATE START TIME ALARM CLOCK SOUND ON BACK Enable Disable Alarm Select Alarm Clock on off by pressing button 3 CLOCK ALARM ALARM O TIME 08 00A Use buttons 1 amp 2 to highlight the time parameter you wish to change use buttons 3 amp 4 to scroll up or down to chage the time Save the changes by pressing button 5 CLOCK ALARM ALARM ON TIME 08 00 a Symbol 15 displayed when Alarm Clock is enabled Selecting Sound Vibration Select Sound Vibration setting by pressing buttons 1 or 2 to highlight the feature Press button 3 to select It TIME DATE Page 4 Astra 777 TC Return to Previous Screen Select Previous Screen by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it TIME DATE START TIME ALARM CLOCK SOUND ON BACK SIS TUN Parameters Press and hold Buttons 2 and 3 until program features are displayed Select system setting by pressing buttons 1 or 2 to highlight the pager Press button 3 to select the system features Siren Chirp Enable Disable Select Siren Chirp setting by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it Sytem Responce FEATURE ON Passive Arm Enable Disable Select Passive Arm setting by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it SIREN CHIRP PASSIVE ARM COLD TEMP HOT TEMP BACK Sytem Responce FEATURE ON Astra 777 TC Page
10. When the battery needs replacing the system s operating range will decrease or the transmitter LED may not be as bright In order to change the battery first remove 2 screws from the back of the transmitter and separate the top and bottom halves of the case While replacing the battery make sure that the positive and negative terminals are positioned correctly then carefully reassemble the transmitter case Astra 777 TC Page 17 System Operation Remote Arming The system monitors 4 independent areas zones while armed doors hood trunk shock sensor and optional sensor input To Arm the System 1 Turn off the ignition 2 Press Button 1 The siren will chirp once The doors will lock The parking lights will flash once The LED will turn on to indicate the starter defeat is activated 3 5 seconds after Arming The LED will start blinking to indicate that the doors and hood trunk inputs are being monitored During Arming if the system detects a bad sensor or an open zone the system will chirp 4 additional times and ignore that input but keep all other areas protected Once Armed the alarm will trigger when any of the following occurs The doors are opened The hood or trunk is opened The shock sensor detects an impact to the vehicle The optional sensor is disturbed When the alarm triggers the siren will sound the horn will honk and the parano lights will flash If the system i
11. holding transmitter button 5 will scroll through several transmitter programmable options TEMPERATURE ENABLE COLD START ENABLE HOT START VALET MODE ENABLE AUTOSTART 1 ENABLE AUTOSTART 2 TEMPERATURE Check the temperature inside the vehicle 1 Press and hold Button 5 until the display shows TEMPERATURE 2 Release Button 5 transmitter will beep four times ENABLE COLD START Auto Start Cold Temperature Activation Mode 1 Press and hold Button 5 until the display shows ENABLE COLD START 2 Release Button 5 The transmitter will beep display will show Auto Start Cold Temperature setting 3 Press and hold Button 5 until the display shows CONFI RM 4 Release Button 5 The transmitter will beep The display will show FEATURE ON indicating that Auto Start Cold Temperature Activation Mode is enabled ENABLE HOT START Auto Start Cold Temperature Activation Mode 1 Press and hold Button 5 until the display shows ENABLE HOT START 2 Release Button 5 The transmitter will beep display will show Auto Start Cold Temperature setting 3 Press and hold Button 5 until the display shows CONFI RM 4 Release Button 5 The transmitter will beep The display will show FEATURE ON indicating that Auto Start Cold Temperature Activation Mode is enabled VALET MODE Valet mode function sets and resets the security system valet mode this function is enabled only when the system is disarmed unlocked S
12. wire PASSENGER SWITCH LINL CHECK 57 n B PASSENGER DOOR 30 DRIVER DOOR MOTORS MOTOR FACTORY cs E DOOR LOCK se Y gs E MODULE Groan wir ofa LINLOGK From Inverter or a Relay Astra 777 TC Page 31 Two 5 He Two Stage Reverse Polarity 86 97 ET Green wire LOCK 87a Door Lock wire Door Unlock wire DOOR LOCK SWITCH Blue white wire PASSENGER UNLOCK y 86 85 CUT gt 02 m Z ITI A 15A FUSE DRIVER DOOR MOTORS Lal a La L us a ES 12V ALI FACTORY DOOR LOCK 86 97 85 E MODULE Blue wire 87a UNLOCK 30 l Two Stage Adding Actuators PASSENGER DOOR MOTORS Blue white wire 86 97 85 Q Q Q PASSENGER gt UNLOCK dh 30 IE 86 9 g5 Green wire a LOCK 87a 30 15A FUSE nl 12V i I 86 97 Blue wire UNLOCK 87a 30 DRIVER DOOR MOTOR Page 32 Astra 777 TC FCC ID OARRXAM2000 This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Call Emergengy Override Valet Switch LED Light Astra 777 TC Page 33 Page 34 Astra 777 TC Astra 777 TC Pa
13. 1 or 2 to highlight the feature Press button 3 to select it PGR CLK SYNC SYS CLK SYNC START 1 TIME START 2 TIME EXIT Security system responce Start Time 1 This feature sets the system Autostart 1 time Select Sytem Clock Sync by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it PGR CLK SYNC SYS CLK SYNC START 1 TIME SYSTEM CLOCK SET START 2 TIME EXIT Use buttons 1 amp 2 to highlight hours or minutes use buttons 3 amp 4 to scroll up or down to chage the time Astra 777 Page 7 START 1 SET SET TIME TIME 8 00 Use buttons 1 amp 2 to highlight Set Time press button 3 AUTOSTART 1 TIME 8 00A The security system responce Start Time 2 This feature sets the system Autostart 2 time Select Sytem Clock Sync by pressing buttons 1 or 2 to highlight the feature Press button 3 to select it PGR CLK SYNC SYS CLK SYNC START 1 TIME START 2 TIME Use buttons 1 amp 2 to highlight hours or minutes use buttons 3 amp 4 to scroll up or down to chage the time Use buttons 1 amp 2 to highlight Set Time press button 3 START 2 SET SET TIME TIME 8 00A The security system responce AUTOSTART 2 TIME 8 00A RUOLI CERVI 11 16 3 10P Select Alarm History by pressing buttons 3 or 4 to highlight the feature Press button 1 to select it Page 8 Astra 777 TC Poe rexit ee rae exe USING tne Color Remote Pressing and
14. 12V power Pin 2 WHITE WIRE Parking Light Output relay Connect the White wire to the circuit that shows 12V or ground only when the parking lights are on and set the internal parking light relay jumper to the proper polarity For parking light circuits exceeding 10 amps a relay is required For vehicle s with independent left and right parking light circuits diodes must be installed to keep the circuits separate NOTE Do not connect the WHITE wire to the vehicle s headlight circuit Pin 3 BROWN WIRE Siren Output The BROWN wire must connect to the siren s red wire The BLACK siren wire must be grounded Pin 4 BLUE WHITE Passenger Unlock output 500mA Connect to an optional relay to unlock the passenger doors for two stage unlock see Two Stage Door Lock Diagrams Pin 5 WHITE RED WIRE Auxiliary 2 Output 500mA Connect to a relay or module for an optional feature such as power window activation or remote start etc Pin 6 ORANGE WIRE Armed Output 500mA The ORANGE wire provides a ground output while armed to activate an optional starter defeat relay or other device such as a power window control module Pin 7 BROWN WHITE WIRE Horn Output 500mA Connect to an optional relay to activate the vehicle s horn when the alarm 15 triggered Pin 8 BLACK WHITE WIRE Dome Light Output 500mA Connect to an optional relay for dome light activation See GREEN and VIOLET door trigger wires NOTE MUST USE RELAY Pin 9
15. Ur EE CR doles Page 25 PIUGSIANCONNECEONS casas spot esed Rd e edt ded Be cape Sus ee Ae dris Page 26 Jamper SCUWINGS sd e aderunt EOS ERA E ULIS Pe aai qd ees Page 26 8 System Program spediti ESA ANA AA a Page 27 Entering System Programming ira CAES P te de ote rai Page 27 Deu Reset ee ea deni cu e SO A ac a e d Page 27 Programmable System DEOS i de ee Ho m EO dor dele qe Win cete el Page 27 Branch Table cv edotto sod det edu we aite dex dos Deed qud opa Page 29 9 DOOR LOCK eri aa aa od Ae esmerada tii alada Sor aco b be b S Page 30 10 TWO Stage DOOr Lock deus scat n b Re E e Red e ee RS Page 31 Il TECHNICA ATOR VATION cis drena ia add Page 33 12 Wiking Diada tea c det et ore eos ds SA nd dead n Back Page About Your System Congratulations on your purchase of this state of the art vehicle security system from ScyTek Electronics With proper installation this system will provide superior protection and performance for many years to come System Contents Main Unit One 5 Button 2 Way LCD Remote Transmitter One 5 Button Random Code Remote Transmitter 2 Way Pager Transceiver Antenna High Output 6 tone Siren Dual Stage Shock Sensor Status LED e Coded Emergency Override Valet Switch Call Butt
16. e 30 seconds the output will turn off Latched operation provides an output that turns on when the transmitter button is pressed and remains on until the transmitter button is pressed again Ignition Armed Mode When enabled the security system may also be manually armed and disarmed using the transmitter while the ignition is on Extended Parking Lights When selected the parking lights will remain ON for 30 seconds after disarming the system Warn Away Pager Report When Enabled Warn Away report will be sent to the pager If Disabled no Warn Away report will be sent to the pager Page 28 Astra 777 TC 21 Smart Siren Mode When Enabled works with Optional ScyTek MP Player Siren Unit Branch Feature Button 1 default Button 2 Button 3 1 Horn Chirps w Arm amp Disarm Normal Horn Chirps 2 Arm Mode Manual Arming Passive Armino 3 Passive Door Locking Disabled Enabled 4 Ignition Controlled Locks On Off Set Override Code 5 Ignition Controlled Unlock All Driver Onl Disabled 6 Ignore Open Door Report Off Ignore 10 Disarm with Aux 1 Disabled Enabled 14 Horn Honk Output Flashino Continuous 21 MP Player Siren Mode Disabled Enabled Astra 777 TC Page 29 Follow the diagrams below for connecting basic door lock systems For Two Stage door lock systems separately unlocks driver and passenger doors see following pages Negative Trigger Positive Trigger Green wire LOCK 86 97 85 Unl
17. errupt or system was reset example flash flash pause flash flash pause shock sensor Silent Arming Disarming The system can be programmed to operate without Arm and Disarm chirp indications When programmed for full time silent operation the siren will sound only when the system is triggered The system 15 also capable of temporary silent operation if desired Pressing the Shift button before Arming or Disarming the system will bypass the chirp confirmations and allow one time silent operation Note The open zone warning chirps will not be bypassed when the system is Armed Disarmed silently Passive Arming When programmed for the optional Passive Arming feature the system arms itself automatically each time the ignition is turned off and all of the doors hood and trunk are closed To start the Passive Arming Process 1 Turn off the ignition 2 Open the door and exit the vehicle Once all doors are closed and the dome light is off the LED will begin flashing rapidly Parking Lights will flash twice three seconds after passive arming cycle began 3 After 30 seconds The siren will chirp The parking lights will flash The doors will lock The status LED will begin flashing 4 The system is now If the Passive Locking feature is selected Astra 777 TC Page 19 Panic Mode In the event of an emergency the transmitter s remote Panic feature can be used to instantly trigger the alarm
18. et or reset the Valet mode 1 Press and hold Button 5 until the display shows VALET or DI SARM The transmitter will beep 2 Release Button 5 The display will show VALET MODE The transmitter will beep twice and the siren will chirp twice if the Valet mode was reset The symbol ENABLE AUTOSTART 1 ENABLE AUTOSTART 2 1 Press and hold Button 5 until the display shows ENABLE AUTOSTART 1 or ENABLE AUTOSTART 2 AUTOSTART 1 2 Release Button 5 TIME 8 00A The transmitter will beep The display will show Auto Start 1 or 2 time setting AUTOSTART 2 3 Press and hold Button 5 until the display shows CONFI RM TI ME 5 00P 4 Release Button 5 The transmitter will beep The display will show FEATURE ON indicating that Auto Start 1 or 2 Activation Mode is enabled Astra 777 TC Page 9 DION e ON ELON Transmitter Lockout Press and hold buttons 2 amp 4 simultanously for 3 seconds to lockout the transmitter against accidental transmission Release Transmitter Lockout f Press and hold buttons 2 4 simultanously for 3 seconds e Los to release the transmitter from Lockout Out of Range Report pager report if no responce from the unit Transmitter Transmitter Locked Unlocked Temperature Temperature Engine Start Engine Start Engine Run Engine Stoped Set read Page 10 Astra 777 TC Pager SES Display Time time of day clock Date Engine Run Timer date or engine run minute time
19. et the Emergency Override Code 1 Turn on ignition 2 Within 5 seconds press the valet switch 5 times The siren will provide one long chirp indicating that you have entered Programming 3 Press the valet switch 4 times The siren will chirp each time the valet switch is pressed 4 Within 5 seconds press Button 3 on the transmitter The siren will chirp 3 times 5 Press the valet switch the number of time equal to the desired code from 1 15 Page 20 Astra 777 TC 6 Turn off the ignition then arm the system 7 Disarm the system using the new Override Code to permanently store the new code Note If the code set procedure is not properly performed turn off the ignition and begin again The override code will not be permanently stored until the code is used to disarm the system Automatic Rearming The Automatic Rearming feature 15 designed to protect the vehicle in the event the system is accidentally disarmed With the Automatic Rearming feature enabled the alarm will automatically rearm and lock 30 seconds after disarming Note Door open trigger does not stop the Rearm Cycle Valet Mode The Valet Mode temporarily disables the security system so the vehicle may be operated by a mechanic or parking attendant To activate or deactivate the Valet Mode 1 Turn the ignition 2 Press and hold the override switch for 5 seconds The siren will chiro once and the LED light will stay ON to confirm the Valet Mode i
20. feature may be programmed to unlock all doors or the driver s door only If driver s door only is selected the optional Passenger Unlock feature must be connected See Two Stage Door Lock Diagrams Astra 777 TC Page 27 10 11 12 13 14 15 16 17 18 19 20 Ignore Open Door Report Bypasses the open zone warning chirps for vehicles equipped with a residual dome light circuit that remains ON for a period of time after closing the door Auto Rearming Mode When selected the system will automatically re arm and lock 30 seconds after it has been disarmed regardless if a door is open or closed Door Unlock Pulse Selects between one pulse or two pulse operation for the door unlock output Vehicles that require two pulses on the proper wire to unlock the doors can be interfaced directly without the use of relays or any additional circuitry by programming the system for double unlock pulse Arming Chirps Selects between normal and silent operation Disarm with Auxiliary 1 When selected activating the Auxiliary 1 output usually used to open the trunk will disarm the alarm Door Lock Pulse Length Selects between a 1 3 or 0 1 second output for door locking and unlocking Program to 3 seconds for vehicles equipped with vacuum door locking systems Anti Carjack Type Selects one of three modes for Anti Carjacking Active Passive or Full Time Manual When selected pressing Button 4 will automatically en
21. from the driver s position 4 Pin White Connector Plug in connector port for dual stage shock sensor Jumper Settings Jumper Selection Carefully separate the top and bottom halves of the main unit case Once the cover is removed the parking light polarity jumper will be visible next to the parking light relay Set the jumper for the correct polarity output as described below then reassemble the main unit case Parking Light Output Selects the polarity for the output of the on board Parking Light relay Left Pin Center Pin positive Right Pin Center Pin negative default setting shown Page 26 Astra 777 TC System Programming Entering System Programming To enter System Programming 1 Turn on ignition 2 Within 5 seconds press the valet switch 5 times The siren will provide three chirps indicating that you have entered Programming 3 Press the valet switch the number times equal to the System Option you want to change The siren will chiro each time the valet switch is pressed 4 Within 5 seconds press the transmitter button corresponding to the desired operating mode for that System Option The siren will chirp to indicate the setting 1 chirp Button 1 2 chirps Button 2 3 chirps Button 3 5 When youare finished turn off the ignition to save the changes Default Reset Following this procedure will set all Programmable System Options to factory default settings 1 Enter System Progra
22. gage the Anti Carjacking feature Passive When selected the Anti Carjacking feature will activate whenever a door is opened while the ignition is on Full Time When selected the Anti Carjacking feature will automatically activate each time the ignition is turned on Anti Carjack Mode Enables Anti Carjacking protection Horn Honk Output Selects the output when activated to be pulsing or constant Aux 2 Auto Activate with Arm When selected the Auxiliary 2 output will activate when the system is armed This feature can be used to roll up windows close sunroofs activate accessories etc Auxiliary 1 Mode Selects from momentary 10 second timed or latched operation for Auxiliary 1 Momentary operation provides an output for as long as the transmitter button is pressed Timed operation provides an output that turns on for 10 seconds each time the transmitter button is pressed If the button is pressed again during the 30 seconds the output will turn off Latched operation provides an output that turns on when the transmitter button is pressed and remains on until the transmitter button is pressed again Auxiliary 2 Mode Selects from momentary 10 second timed or latched operation for Auxiliary 2 Momentary operation provides an output for as long as the transmitter button is pressed Timed operation provides an output that turns on for 10 seconds each time the transmitter button is pressed If the button is pressed again during th
23. ge 35 Wiring Diagram Valet Switch Green Lock output Red not used Blue Unlock output Red 12V White Parking light output 7A Brown Siren output Blue White Passenger Unlock output 500mA White Red Auxiliary 2 outout Orange Armed output Brown White Horn output 500mA Black White Dome Light output 500mA Blue Hood Trunk input Gray Auxiliary 1 output 500mA Yellow Ignition 12V Black Ground Violet Door Trigger input Green Door Trigger input ScyTek Electronics 11627 Cantara Street North Hollywood CA 91605 www scytek net ScyTek Electronics 2008 Astra 777 TC 6 10 08
24. hen the system is disarmed using the Remote Transmitter The dome light will remain on for 30 seconds or until the ignition is turned on Auxiliary Function Outputs The Astra 777 TC system is equipped with 2 Auxiliary Outputs allowing the convenience features of the system to be further expanded These outputs can be used to add a number of optional features such as power trunk release remote engine start power window activation power sunroof control and more Disarm with Auxiliary Function If Auxiliary 1 is installed to activate the vehicle s trunk release the system can be programmed to automatically disarm the alarm when the trunk is opened using the transmitter n this manner the trunk can be accessed without first disarming the alarm Remote Sensor Disable When parking the vehicle in areas susceptible to unwanted disturbance from animals or strong weather conditions that could cause the sensors to trigger the sensor inputs can be temporarily bypassed using the Remote Transmitter preventing possible false alarms To disable the sensor inputs 1 Arm the system normally 2 Within 5 seconds of Arming the system press the Arm button again The siren will chirp 5 times and the parking lights will flash 5 times to indicate the sensors are disabled The sensors will remain disabled until the next arming cycle Anti Carjacking Protection For a higher level of personal security the system is equipped with three programmab
25. ivated feature Page 1 pra 1 Arms and Locks the system and when held for 3 seconds activates the system s Panic feature Button 1 also locks the doors when the system is in Valet Mode Button 2 Disarms and Unlocks the system Pressing Button 2 again operates the Passenger Unlock feature if installed Button 2 also unlocks the doors when the system is in Valet Mode Button 3 Activates the Auxiliary 1 output normally used for trunk release note trunk icon on button Button 4 Activates the Remote Start feature Button 5 is the Confirmation Programming and the Page Shift button Quickly pressing button 5 will activate the Page 2 function Pressing button 5 for 2 seconds activates the system s confirmation feature which will then display the current status of the system armed disarmed engine running etc Page 2 Button 1 Silently Arms Locks the system press and release button 5 then press button 1 Button 2 Silently Disarms Unlocks the system press and release button 5 then press button 2 Button 3 Activates the Auxiliary 2 output press and release button 5 then press button 3 Button 4 Aux 3 or Factory Rearm output press and release button 5 then press button 4 Button 5 not used Page 3 4 are used as Page 1 amp 2 for second car operation System Confirmation The 2 way transmitter s confirmation feature allows the current vehicle status to be displayed at any time To display system status 1 Press and hold
26. key On Off On Off and back On siren will chirp 3 times 2 Press and hold the Override switch for 5 seconds The siren will chirp 5 times The LED will illuminate 3 Press Button 1 on the first transmitter The siren will chirp once 4 Press Button 1 on the first transmitter again The siren will chirp twice to indicate it has learned the code 5 Repeat steps 3 and 4 for each transmitter up to 4 6 Turn off the ignition key Two Car Operation If two vehicles are equipped with Astra 777 TC systems for convenience both can be operated using the same remote transmitter all four transmitters are to be used with both cars program transmitters A and B into the first vehicle in the manner described above Program transmitters C and D by pressing the Shift button twice before performing steps 3 and 4 above When finished programming the first vehicle program transmitters C and D into the second vehicle as normal then program transmitters A and B by pressing the Shift button twice before performing steps 3 and 4 above When programmed in this manner the driver of the first car can also operate the second vehicle by pressing the Shift button twice and the desired function button Battery Replacement Your Remote Transmitter uses a 12 volt alkaline battery type 23A which will require replacement in time Depending on the amount of use the battery may last up to six months or more before it needs replacement
27. ks the system Button 1 also locks the doors when the system is in Valet Mode Button 5 then Button 2 Silently Disarms and Unlocks the system also unlocks the doors when the system is in Valet Mode If the Optional Keyless Entry Feature is installed Page 12 Astra 777 TC Adding Replacing 2 way LCD Transmitters 2 LCD remotes maximum When adding an optional 2 way LCD transmitter to the system follow these steps 1 Turn on the ignition key On Off On Off On Off and back On Key On 4 times The siren will chirp 4 times 2 Press and hold the Override switch for 5 seconds The siren will chirp 4 times The LED will illuminate 3 Press Button 1 on the first transmitter then on the second transmitter The siren will chiro once for each transmitter learned 4 Turn off the ignition key 5 The siren will chirp 3 times to indicate the system has exited programming mode LCD Transmitter Battery Replacement Your Astra Remote Transmitter uses a 1 5 volt AAA alkaline battery which will require replacement in time Depending on the amount of use the battery may last up to three months before it needs replacement When the battery needs replacing the system s operating range will decrease the LCD display will show only one of three bars in the battery icon or the display and sounds may suddenly stop and start as the battery voltage drops below minimum In order to change the battery first slide the battery door locking pi
28. le Anti Carjacking modes When any Anti Carjacking mode is triggered the parking lights will flash twice to confirm activation After 90 seconds the siren will begin chirping for 15 seconds as a warning prior to entering full alarm mode During the full alarm mode the siren will sound the parking lights will flash and the horn will honk for up to five minutes or until the system 15 reset Manual When selected pressing Button 4 of one way remote or page 2 button 3 of the LCD remote with the ignition ON will automatically trigger the Anti Carjacking feature Press the Button again to reset the Manual Anti Carjacking mode Passive When selected the Anti Carjacking feature will activate whenever a door is opened while the ignition is on Press the Valet switch 1 time to reset the Passive Anti Carjacking mode Full Time When selected the Anti Carjacking feature will automatically activate each time the ignition is turned on Press the Valet switch 1 time while the ignition is on to reset the Passive Anti Carjacking mode Note The desired Anti carjacking mode must be programmed during installation Page 22 Astra 777 TC System Installation Thoroughly read and become familiar with the installation instructions before beginning the installation Review system contents Main Unit 1 One Way 5 Button Remote Transmitter 1 Two Way 5 Button LCD Transmitter Siren Shock Sensor Harnesses Reciever Antenna 14 Pin main harness
29. m is out of Valet mode cl System Armed System Disarmed Warn Away Trunk Release Indicates the alarm is Indicates the alarm is Indicates the warn Indicates the trunk ON OFF away has been triggered or auxilliary function has been activated Door Open Shock Sensor Battery Low Trunk Open Indicates the door zone Indicates the shock Indicates the battery Indicates the trunk or has been triggered sensor has been inside the transmitter hood zone has been triggered needs to be replaced triggerd E _ Alarm clock Valet Mode Panic Indicates the Indicates the system Indicates the panic progammable timer has been placed in mode has been has been set valet mode triggered Astra 777 TC Page 15 Remote Transmitter Description The Astra 777 15 supplied with one 5 button Remote Transmitter used to control system operations Button 1 Arms and Locks the system and when held for 5 seconds activates the system s Panic feature Button 1 also locks the doors when the system is in Valet Mode Button 2 Disarms and Unlocks the system Pressing Button 2 again operates the Passenger Unlock feature if installed Button 2 also unlocks the doors when the system is in Valet Mode Button 3 Activates the Auxiliary 1 output This output will remain on for as long as the button is pressed Button 4 Activates the Auxiliary 2 output This output will remain on for as lo
30. mming 2 Press Transmitter Button 3 The siren will chirp 6 times indicating that the reset signal was received All Programmable System Options are now set to factory default settings The Valet Mode is off 3 Turn off ignition Programmable System Options The following is a description of the programming options Some program branches control more than one option and may require accessing a particular branch number twice in order to program all desired features 1 Horn Chirps with Arm amp Disarm Selects one of two modes Normal Horn Chirps Normal When selected the horn will honk only when the alarm is triggered Horn Chirps When selected the horn will provide the arm disarmed trigger indications allowing the siren installation to be skipped 2 Arm Mode Selects one of two modes Manual Arming or Passive Arming Passive Door Locking Selects whether or not the system will automatically lock the doors during Passive Arming 4 Ignition Controlled Locks Override Code Set This dual program branch sets Ignition Controlled Locking and programs the optional Emergency Override Code If Lock Only is selected the doors will not automatically unlock when the ignition is turned off Override Code Set Changes the Emergency Override Code for a higher level of security see page 7 5 Ignition Door Unlocking Selects whether or not the system automatically unlocks the doors when the ignition is turned off The Ignition Door Locking
31. n to the side Carefully slide the battery cover downward until it is free While replacing the battery make sure that the positive and negative terminals are positioned correctly then carefully reassemble the transmitter case Setting The Time The LCD display is equipped with a 12 hour clock that in addition to displaying the time offers an alarm clock function as well as a remote activation timer To set the time 1 Press and hold Buttons 2 and 3 for three seconds The remote will beep two times and three bars will be shown indicating time set mode is entered 2 Press Button 2 until the correct hour 15 displayed 3 Press Button 3 until the desired minute is displayed The button may be held down to scroll faster 4 When the desired time is displayed press Button 5 to store remote will beep 3 times to indicate the time has been set Setting The Alarm Clock The alarm clock function can be set to play an alert melody at a specific time of day To set the alarm clock function 1 Press and hold Buttons 2 and 3 until the remote beeps three times The alarm clock bell and three bars will be shown indicating alarm clock set mode is entered 2 Press Button 2 until the desired hour is displayed 3 Press Button 3 until the desired minute is displayed The button may be held down to scroll faster 4 When the desired time is displayed press Button 5 to store remote will beep 3 times to indicate the alarm clock has been se
32. ng as the button is pressed Button 5 is the Page Shift button The Page Shift button will change the function of Buttons 1 through 4 each time it is pressed allowing access to additional features or multiple car operation Each time the Shift Button is pressed the LED on the transmitter will illuminate and the transmitter functions will shift to the next page allowing access to another set of features Once shifted to another page there are 4 pages total the transmitter will remain on that page for 10 seconds or until a button is pressed then return to page 1 Each time a transmitter button is pressed and held the LED will flash a number of times to indicate from which page it is transmitting Under normal operation only pages 1 and 2 are used Pages 3 and 4 are usually used for Two Car Operation see page 3 Shift then Button 1 Arms and Locks the system silently Shift then Button 2 Disarms and Unlocks the system silently If the Optional Keyless Entry Feature is installed Page 16 Astra 777 TC Adding Replacing One Way Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system have all desired transmitters ready and follow the steps below Note Up to 4 one way transmitters can be programmed to operate the system Any previously stored transmitter code will be erased if it is not programed within the following sequence To program the transmitter s 1 Turn the ignition
33. ock 12V UNLOCK Unlock Door Lock wire FACTORY DOOR LOCK MODULE Door Unlock wire DOOR LOCK SWITCH Reverse Polarity Vacuum Green wire 1 LOCK 15A FUSE EnE 86 97 gs W 87 87a fo 86 85 DOOR LOCK 12V th SWITCH 87a 30 Blue wire FACTORY 15A FUSE UNLOCK MOTOR i f W o nm 12V 13 87 CUT gt 30 Blue wire 30 UNLOCK Green wire LOCK CUT DOOR LOCK SWITCH Adding Actuators Green wire AFTER MARKET LOCK MOTORS 15A FUSE A 2 W 12V 86 87 85 87a 30 s Si du 87a 30 Blue wire UNLOCK Page 30 Astra 777 TC VACUUM PUMP Two Sie Doc QI DIACKAINIS The Astra 777 TC is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock operation When connected as shown below disarming the system will unlock only the driver s door Pressing the disarm button again will unlock all doors Two Stage Negative Trigger Door Lock wire Green wire LOCK Door Unlock wire m Blue white wire DOOR LOCK aa T SWITCH Blue wire UNLOCK PASSENGER DOOR 15A FUSE DRIVER DOOR MOTORS TT I MOTOR ln 12V 1 1 FACTORY DOOR LOCK MODULE 87 85 87a 30 Ls Two Stage Positive Trigger Door Lock wire Door Unlock wire Blue wir From Inverter or Relay LOCK
34. on built into the antenna See Page 23 Options and Accessories This ScyTek system includes several optional inputs and outputs allowing the creation of a completely personalized security and convenience system by offering many optional features Such as May require additional parts and or labor see store for details Second Car Operation Remote Car Start Remote Door Locking Power Trunk Hatch Release Two Stage Door Unlocking Glass Breakage Sensor Starter Defeat Radar Sensor Horn Honk Auxiliary Lighting Control Illuminated Entry Back up Battery Siren Remote Window Control PLEASE NOTE Some of the features described in this manual may require additional parts and or labor and may not be included as part of the standard installation of this unit Additionally many features of this security system have selectable options that must be activated or programmed during the system s installation These items will be identified in the following sections Please discuss these features and any questions you may have regarding the installation of this product with Your Authorized Dealer Astra 777 TC 1 2 MINT COLOR REMO SLE OSSIA DESCRI E LU ON date engine run timer time 11 16 3 10P 11 14 10 14 A Button 3 Button 4 Button 5 Battery alarm autostart Button 2 status enabled enabled The 2 way Color remote transmitter is offering increased range and confirmation of any act
35. r if remote start activated 20 min max Battery Status displays remaining battery life Wakeup Alarm displays Wakeup alarm enabled Autostart Remote Start Autostart enabled Transmit Pager transmission in progress date engine run timer time System Status Battery alarm autostart status enabled enabled Astra 777 TC Page 11 2 way LCD Remote Transmitter Description Optional Button 1 Button 2 Button 3 Button 4 Button 5 The Astra s 777 2 way LCD remote transmitter is offering increased range and confirmation of any activated feature Page 1 Button 1 Arms and Locks the system and when held for 5 seconds activates the system s Panic feature Button 1 also locks the doors when the system is in Valet Mode Button 2 Disarms and Unlocks the system Pressing Button 2 again operates the Passenger Unlock feature if installed Button 2 also unlocks the doors when the system 15 in Valet Mode Button 3 Activates the Auxiliary 1 output normally used for trunk release note trunk icon on button Button 4 Activates the Auxiliary 2 output Button 5 is the Confirmation Programming and the Page Shift button Quickly pressing button 5 will activate the Page 2 function Pressing button 5 for 2 seconds activates the system s confirmation feature which will then display the current status of the system armed disarmed engine running etc Page 2 Button 5 then Button 1 Silently Arms and Loc
36. ransmite becera eni Page 2 Remote Transmitter Description Page 2 11 2 way LCD Remote Transmitter Description Page 12 Adding Replacing 2 way LCD Transmitters Page 13 BatteryiREPIAGEMEN xao deus dor bow bese whew oc er oe e einen Page 13 The Tei ta a a EA AA A Page 13 ivi a A aca A de AAN A ca Page 13 ECDUBACKMIOAE atada Vn fep LA Ed ESA dct de Df a d diz Page 14 Systemic ont etab adora riscos rara da ds add Page 14 Transmitter bn vas daa rot 3003 Ic eo Page 14 ECD ICOM duc eod ite an oe E PROS DE 15 3 Remote Pas A setae Rd es AS A A Page 16 Remote Transmitter Description 16 Replacing Transmitters 2 3 49 Robie dc p BO KC eta dC de Page 17 TWO Car era lena FL Page 17 BatteryReplaCEMene a Cte aa Ee e MN MC nn e RE e d Page 17 4 System OP Troto ii A C RU d doe acte a a eee abu d Page 18 BOOTE APO AO seria ei a P dea CAA ence ace Page 18 Remote entitled qoe Wate do arch us dro Sie ene a EO TA Page 18 TAME a
37. ration of any vehicle components such as foot pedals steering column air vents seat rails etc Do not mount the control unit until after setting the internal jumpers and performing a complete operation check of the system After installation is complete and performance verified the control unit can be easily mounted using wire ties through the mounting tabs on the bottom of the unit Mounting the Siren Choose a siren mounting location that is away from heat sources such as exhaust manifolds and where it cannot be easily accessed from underneath the vehicle Be sure to face the siren downward to prevent the collection of water in the siren s housing Always route all wires from the engine compartment into the interior of the vehicle through a proper grommet Mounting the Shock Sensor Choose a suitable interior mounting location for the shock sensor that provides ample coverage of the vehicle Keep the sensor away from the vehicle s ECM or other sources of electrical interference Suggested mounting locations include air conditioning ducts dashboard braces or center console supports During proper operation the shock sensor will detect impacts to the vehicle only and will not usually be triggered by slow rocking movements of the vehicle like those caused by wind Page 24 Astra 777 TC System Wiring 14 Pin Main Harness Pin 1 RED WIRE 12V Battery Input 15A Fuse The RED wire must be connected to a clean source of continuous
38. s on The siren will chirp twice and the LED light will turn OFF to confirm the Valet Mode is off 3 Turn off the ignition While in Valet Mode the remote transmitters will continue to lock and unlock the doors and operate the optional auxiliary functions DRIVER CALLI NG PAGE FEATURE The Astra 777 15 equipped with a Driver Calling or Paging feature that allows the system to send a page to the LCD transmitter in the event the transmitter has been misplaced or lost within 1500 feet To activate the Driver Calling Page feature 1 Locate the Valet Emergency Override button in your vehicle Ask your installation shop With the ignition switch OFF press and hold the Valet Emergency override button for 2 seconds then release The LCD transmitter will beep continually and the DRIVER CALLING icon will appear Press and release button 5 to turn off transmitter page Astra 777 TC Page 21 Extended Features Ignition Controlled Door Locks For added safety the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on and unlock the doors after the ignition key is turned off If a door is open when the ignition is turned on the ignition locking feature is disabled to protect against locking the keys inside the vehicle Dome Light Activation If the optional Dome Light Activation feature is installed the dome light will turn on w
39. s Es by the doors or hood trunk the system will alarm for 45 onda the shock sensor optional sensor input the system will alarm or 30 seconds In the event the alarm is triggered and remains triggered continuously by the same sensor or input a single arming cycle that sensor or input will be automatically bypassed until the next time the system Is If the Shock Sensor detects a light mpat to the vehicle or the Optional Sensor s warn away zone is disturbed the siren will chirp 5 times as a warning indication Remote Disarming To Disarm the System Press Button 2 The siren will chirp twice The doors will unlock The parking lights will flash twice and remain on for 30sec The dome light will turn on The LED will turn off During Disarming if the system was triggered while away from the vehicle the siren will chirp 3 times the parking lights will flash 3 times and the LED will flash to indicate triggered zone See Tamper Alert for zone listing f the optional Dome Light Activation Feature is installed Page 18 Astra 777 TC Tamper Alert If the system was triggered while away the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition The LED indication will repeat 8 times LED Flashes 1 flash optional sensor 2 flashes shock sensor 3 flashes not used 4 flashes door 5 flashes trunk 10 flashes main power int
40. t To disable the alarm clock function 1 Press and hold Buttons 2 and 3 until the remote beeps three times The alarm clock bell and three bars will be shown indicating alarm clock set mode is entered 2 Press Button 1 to disable the alarm clock remote will beep 3 times to indicate the alarm clock has been disabled Astra 777 TC Page 13 LCD Backlight Transmitter Button 5 15 used for confirmation transmitter programming as well as activation of the LCD backlighting for use in the dark Press button 5 to activate the LCD backlight System Confirmation The 2 way transmitter s confirmation feature allows the current vehicle status to be displayed at any time To display system status 1 Press and hold Button 5 until the display shows CON The transmitter will beep once 2 Release Button 5 The transmitter will beep once The icon representing the system s current status will be displayed on the LCD panel Transmitter Programming Pressing and holding transmitter button 5 will scroll through several transmitter programmable options that may or may not be available depending on the model of system installed DEG degress Not applicable on this model CHP Sets the siren confirmation chirps ON or OFF 1 Press and hold Button 5 until the display shows CHP The transmitter will beep 3 times 2 Release Button 5 The transmitter will beep once LCD panel will show a siren if the chirps are enabled or off
Download Pdf Manuals
Related Search