Samsung 173P Computer Monitor User Manual
Contents
1. and all pertinent information supporting the existence of the alleged defect In case of warranty compressor the compressor model tag must be returned to TRUE along with above listed information Any action or breach of these warranty provisions must be commenced within one 1 year after that cause of action has occurred WHAT IS NOT COVERED BY THIS WARRANTY TRUE s sole obligation under this warranty is limited to either repair or replacement of parts subject to the additional limitations below This warranty neither assumes nor authorizes any person to assume obligations other than those expressly covered by this warranty NO CONSEQUENTIAL DAMAGES TRUE IS NOT RESPONSIBLE FOR ECONOMIC LOSS PROFIT LOSS OR SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION LOSSES OR DAMAGES ARISING FROM FOOD OR PRODUCT SPOILAGE CLAIMS WHETHER OR NOT ON ACCOUNT OF REFRIGERATION FAILURE WARRANTY IS NOT TRANSFERABLE This warranty is not assignable and applies only in favor of the original purchaser user to whom delivered ANY SUCH ASSIGNMENT OR TRANSFER SHALL VOID THE WARRANTIES HEREIN MADE AND SHALL VOID ALL WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IMPROPER USAGE TRUE ASSUMES NO LIABILITY FOR PARTS OR LABOR COVERAGE FOR COMPONENT FAILURE OR OTHER DAMAGES RESULTING FROM IMPROPER USAGE OR INSTALLATION OR FAILURE TO CLEAN AND OR MAINTAIN PRODUCT AS SET FORTH IN THE WARRANTY2. 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 12 12 14 14 14 14 14 14 2 12 12 14 14 14 14 14 12 12 12 10 14 14 14 14 12 12 12 10 10 14 14 14 12 12 12 10 10 10 14 14 14 12 12 10 10 10 10 14 14 12 12 10 10 10 8 8 14 14 12 10 10 10 8 8 8 14 12 12 10 10 8 8 8 8 14 12 10 10 8 8 8 8 8 14 12 10 10 8 8 8 6 6 12 10 10 8 8 6 6 6 6 12 10 8 8 6 6 6 6 5 10 10 8 6 6 6 5 5 4 10 8 8 6 6 5 5 4 4 10 8 6 6 6 5 4 4 3 10 8 6 6 5 4 4 3 3 120 14 NN ON WN Www fp RA Wire Gauge for 2 Voltage Drop in Supply Circuits Distance In Feet To Center of Load 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 12 14 14 14 14 14 14 14 12 12 14 14 14 14 14 14 12 12 12 14 14 14 14 14 12 12 12 10 14 14 14 14 12 12 12 10 10 14 14 14 12 12 12 10 10 10 14 14 14 12 10 10 10 10 10 14 14 12 12 10 10 10 10 8 14 12 12 10 10 10 8 8 8 14 12 10 10 10 8 8 8 8 14 12 10 10 8 8 8 6 6 12 10 10 8 6 6 6 6 6 12 10 8 6 6 6 6 6 5 10 10 8 6 6 6 5 5 4 10 8 8 6 6 5 5 4 4 10 8 6 6 5 5 4 4 3 10 8 6 6 5 4 4 3 3 vececcceeeee WWWw trueMfe COM 0006 NNW OC OC NULAR NADA rire PNW HH MW Na ON ON oo rire DON YW INSTALLATION OPERATION INSTRUCTIONS SHELVING INSTALLATION OPERATION SHELF INSTALLATION Step 1 A Hook shelf clips onto shelf standards see illustration B Position all four shelf clips equal in distance from the floor for flat shelves W
3. with door locks are located in warranty packets Glass Door Models Only REMOTE UNITS This section applies to remotes only e Contact True Technical Service for BTU e Remote cabinets must be ordered as remote requirements We do not recommend converting for a standard No wiring necessary between cabinet and self contained to remote system condensing unit All remote cabinets must be hard wired e All remote condensing units purchased from e No castors available True are 208 230 volts single phase e All remote cabinets come standard using 404A If you have any questions regarding this section refrigerant please call True at 1 800 325 6152 e All remote units come standard with expansion valve liquid line solenoid heated condensate pan and defrost timer when applicable c 7 estates www truemfg comM 4 True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS LOCATING Step 2 A Place packing material behind cabinet as a cushion Carefully lay the unit on its back to remove skid When lifting unit remember to leave the cabinet upright for 24 hours before plugging into power source B Remove skid by unscrewing all base rail anchor brackets Place skid to the side C Carefully lift cabinet upright Removing skid from h bottom of cabinet INSTALLATION OF LEGS AND CASTORS Important Safeguard for installation of leg castor Images 1 5 demonstrate p
4. www truemfg comM 13 7 TL LE True Food Service Equipment Inc MAINTENANCE CARE amp CLEANING Stainless Steel Equipment Care and Cleaning Recommended cleaners for certain situations environments of stainless steel 14 A Soap ammonia and detergent medallion applied with a cloth or sponge can be used for routine cleaning B Arcal 20 Lac O Nu Ecoshine applied provides barrier film for fingerprints and smears C Cameo Talc Zud First Impression is applied by rubbing in the direction of the polished lines for stubborn stains and discoloring D Easy off and De Grease It oven aid are excellent for removals on all finishes for grease fatty acids blood and burnt on foods E Any good commercial detergent can be applied with a sponge or cloth to remove grease and oil F Benefit Super Sheen Sheila Shine are good for restoration passivation NOTE The use of stainless steel cleaners or other such solvents is not recommended on plastic parts Warm soap and water will suffice TEREE www truemfg comM 14 TRUE REFRIGERATION MADE IN Ure U S A ske oe WARRANTY INFORMATION U S A amp CANADA ONLY ONE YEAR PARTS amp LABOR WARRANTY TRUE warrants to the original purchaser of every new TRUE refrigerated unit the cabinet and all parts thereof to be free from defects in material or workmanship under normal and proper use and maintenance service as specified by TRUE and upo
5. you to be sure electrical wiring and installation are correct and no shipping damage has occurred Remember our factory warranty does not cover product loss REPLACEMENT PARTS TRUE maintains a record of the cabinet serial number for your freezer If at any time during the life of your cooler a part is needed you may obtain this part by furnishing the model number and serial number to the company from whom you purchased the cooler Call Toll Free 800 424 TRUE Direct to Parts Department 800 325 6152 U S A amp Canada only or call 636 240 2400 Defrost Time Periods Smaller freezer Worktop and Undercounter units have an automatic defrost As soon as the unit is plugged into a power source a defrost will automaticly start in eight hours A defrost period will occur every eight hours after connecting to power source Larger Worktop amp Undercounter freezers have a different defrost timer See instructions on the next page for operation information Ure DEFROST TIMER INSTRUCTIONS Defrost Time Clock Operation Instructions for TUC 60 32F 67F 93F TWT 60 32F 67F and 93F models RECOMMENDED DEFROST SETTINGS True Manufacturing has factory set your defrost time clock to a recommended time and duration defrost scenario Your True equipment has been designed for three defrost periods 6 00 a m 2 00 p m and 10 00 p m If you decide to deviate from these defrost time settings please follow the
6. ING Always follow the manufacturers recommended settings when programming the amount and duration of the defrost cycles 1 1 putettiy H R k i ty ha aire 5 p j oe MINS Defrost Timer Image 2 hy F t rj STEP 1 The white tabs located on the outmost area of the time clock have been factory set for 6 00 a m 2 00 p m and 10 00 p m Each tab represents 15 minutes of defrost time Notice that at each defrost time two white tabs are set for 15 minutes each for a total of 30 minutes of defrost STEP 2 In order to program the time to begin the defrost cycle flip the white tabs out to set the defrost time To eliminate a defrost time flip the white tabs back toward the center of the Defrost Timer STEP 3 True recommends a 30 minute defrost cycle three times per day sully Ri S sii Ds i po O CS ar a H a I i d 2 om a 1 ak ed 5 sid sm tj A ah r _ a he a es fy ef Wey ey Defrost Timer Box Image 1 Outer most dial White tabs represent 15 minutes of defrost time Time of day Inner most dial True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS CONDUCTORS AND CIRCUITS 115 Volt Amps Nn BW WN 230 Volts Amps O OANNN Wire Gauge for 2 Voltage Drop in Supply Circuits Distance In Feet To Center of Load 20 30 40 50 60 70 80 90 100 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14
7. IRE SHELVES Wire shelves are oriented so that cross support bars are facing down Step 2 Place shelves on shelf clips making sure all corners are seated properly AMISIT Uy A Veron TATAN LIGHT SWITCH LOCATION Light switch location depends upon the TUC amp TWT freezer glass door models Most models will have the light switch located inside the unit above the door Most instances the switch is located next to the light on the ceiling 1 enegneenoaene www truemfg comM 10 True Food Service Equipment Inc MAINTENANCE CARE amp CLEANING MAINTENANCE CARE amp CLEANING CLEANING THE CONDENSER COIL When using electrical appliances basic safety precautions should be followed including the following REQUIRED TOOLS e Phillips Screwdriver e Stiff Bristle Brush e Adjustable Wrench e Vacuum Cleaner Step 1 Disconnect power to unit Step 2 Remove the rear grill by backing out two screws See image 3 Step 3 Remove bolts anchoring compressor assembly to frame rails and carefully slide out tube connections are flexible Step 4 Clean off accumulated dirt from the condenser coil and the fan with a stiff bristle brush See image 1 Step 5 Lift cardboard cover above fan at plastic plugs and carefully clean condenser coil and fan blades Step 6 After brushing condenser coil vacuum dirt from coil and interior flo
8. PACKET PROVIDED WITH THE UNIT ALTERATION NEGLECT ABUSE MISUSE ACCIDENT DAMAGE DURING TRANSIT OR INSTALLATION FIRE FLOOD ACTS OF GOD TRUE is not responsible for the repair or replacement of any parts that TRUE determines have been subjected after the date of manufacture to alteration neglect abuse misuse accident damage during transit or installation fire flood or act of God IMPROPER ELECTRICAL CONNECTIONS TRUE IS NOT RESPONSIBLE FOR THE REPAIR OR REPLACEMENT OF FAILED OR DAMAGED COMPONENTS RESULTING FROM ELECTRICAL POWER FAILURE THE USE OF EXTENSION CORDS LOW VOLTAGE OR VOLTAGE DROPS TO THE UNIT NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THERE ARE NO OTHER WARRANTIES EXPRESSED IMPLIED OR STATUTORY EXCEPT THE ONE 1 YEAR PARTS amp LABOR WARRANTY AND THE ADDITIONAL FOUR 4 YEAR COMPRESSOR WARRANTY AS DESCRIBED ABOVE THESE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES INCLUDING IMPLIED WARRANTY AND MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF OUTSIDE U S This warranty does not apply to and TRUE is not responsible for any warranty claims made on products sold or used outside the United States REMOTE CONDENSERS True warrants the original purchaser of the remote cabinet one year parts and labor coverage for all cabinet parts thereof to be free from defects in material or workmanship under no
9. TRUE FOOD SERVICE EQUIPMENT INC 2001 East Terra Lane P O Box 970 O Fallon Missouri 63366 636 240 2400 FAX 636 272 2408 INT L FAX 636 272 7546 800 325 6152 Parts Department 800 424 TRUE Parts Department FAX 636 272 9471 INSTALLATION MANUAL FOR UNDERCOUNTER FREEZERS amp WORKTOP FREEZERS TABLE OF CONTENTS TUC 27FG Safety Information Safety Precautions Proper Disposal Connecting Electricity Adapter Plugs OWN Installation Operation Instructions Ownership Required Tools Uncrating Locating amp Installation of Leg Castors Leveling Cabinet Electrical Instructions Start up Defrost Timer Instructions Wire Gauge Chart _ Shelving Install Operation amp Light Switch OONDOoFR AA Maintenance Care amp Cleaning Cleaning Condenser Coil 11 12 Cabinet Cleaning _ 13 14 Warranty U S A amp Canada Only 15 TWT 44F HD Spanish German French and Dutch versions included CONNU TUN ONNI You have just purchased the finest commercial freezer available You can expect many years of trouble free operation TWT 60F UNDERCOUNTER amp WORKTOP FREEZERS 11 3 08 3k SB 912633 True Food Service Equipment Inc TWHLLLE NOTICE TO CUSTOMER 2E a Loss Or Spoilage Of Products In Your Refr
10. WARNING HOW TO CONNECT ELECTRICITY Do not under any circumstances cut or remove the third ground prong from the power cord For personal safety this appliance must be properly grounded The power cord of this appliance is equipped with Never unplug your freezer by pulling on the power a 3 prong grounding plug which mates with a cord Always grip plug firmly and pull straight out standard 3 prong grounding wall outlet to from the outlet minimize the possibility of electric shock hazard Repair or replace immediately all power cords that from this appliance have become frayed or otherwise damaged Do not Have the wall outlet and circuit checked by a use a cord that shows cracks or abrasion damage qualified electrician to make sure the outlet is along its length or at either end properly grounded When removing the freezer away from the wall be If the outlet is a standard 2 prong outlet it is your careful not to roll over or damage the power cord personal responsibility and obligation to have it replaced with the properly grounded 3 prong wall outlet The freezer should always be plugged into it s own individual electrical circuit which has a voltage rating that matches the rating plate This provides the best performance and also prevents overloading building wiring circuits which could cause a fire hazard from overheated wires USE OF ADAPTER PLUGS NEVER USE AN ADAPTER PLUG Because of potential safety hazards und
11. ace Leveling Shim Ure True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS LEVELING Step 4 A Set unit in its final location Be sure there is adequate ventilation in your room Under extreme heat conditions 100 F 38 C you may want to install an exhaust fan Warning Warranty is void if ventilation is insufficient B Proper leveling of your True freezer is critical to operating success for non mobile models Effective condensate removal and door operation will be effected by leveling C The freezer should be leveled from inside the cabinet Place a level on the inside floor of the unit front to back and side to side D Ensure that the drain hose or hoses are positioned in the pan E Free plug and cord from inside the lower rear of the cooler do not plug in F The unit should be placed close enough to the electrical supply so that extension cords are never used Warning Compressor warranties are void if the unit is more than 7 ft 2 1m from plug in connection TRUE will not warranty any units that are connected to an extension cord ELECTRICAL INSTRUCTIONS Step 5 A Before your new unit is connected to a power supply check the incoming voltage with a voltmeter If anything less than 100 of the rated voltage for operation is noted correct immediately B All units are equipped with a 7 ft 2 1m service cord and must be powered at proper operating voltage
12. at all times Refer to cabinet data plate for this voltage True requires that a sole use circuit be dedicated for the unit Failure to do so voids warranty WARNING Compressor warranties are void if compressor burns out due to low voltage WARNING Power supply cord ground should not be removed NOTE To reference wiring diagram Remove front louvered grill wiring diagram is positioned on the inside cabinet wall True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS STARTUP Step 6 A The compressor is ready to operate Plug in the cooler B Temperature control set at No 4 position gives freezers an approximate temperature of 10 F Allow unit to function several hours completely cooling cabinet before changing the control setting C Excessive tampering with the control could lead to service difficulties Should it ever become necessary to replace temperature control be sure it is ordered from your True dealer or recommended service agent D Good air flow in your True unit is critical Be careful to load product so that it neither presses against the back wall nor comes within four inches of the evaporator housing Refrigerated air off the coil must circulate down the back wall NOTE If the freezer is disconnected or shut off wait five minutes before starting again RECOMMENDATION Before loading product we recommend you run your True unit empty for two to three days This allows
13. dirt adequately please call your refrigeration service company The Condenser looks like a group of vertical fins You need to be able to see through the condenser for the unit to function at maximum capacity Do not place filter material in front of condensing coil This material blocks air flow to the coil similar to having a dirty coil THE CLEANING OF THE CONDENSER IS NOT COVERED BY THE WARRANTY HOW TO CLEAN THE CONDENSER 1 Disconnect the electrical power to the unit 2 Remove the louvered grill 3 Vacuum or brush the dirt lint or debris from the finned condenser coil 4 If you have a significant dirt build up you can blow out the condenser with compressed air CAUTION MUST BE USED to avoid eye injury Eye protection is recommended 5 When finished be sure to replace the louvered grill The grill protects the condenser 6 Reconnect the electrical power to the unit If you have any questions please call True Manufacturing at 636 240 2400 or 800 325 6152 and ask for the Service Department Service Department Availability Monday Friday 7 30 a m to 5 30p m and Saturday 7 45 a m to 11 45 a m CST Condenser o ONBSeegwrastcn www truemfg comM 12 MAINTENANCE CARE amp CLEANING Stainless Steel Equipment Care and Cleaning CAUTION Do not use any steel wool abrasive or chlorine based products to clean stainless steel surfaces E Stainless Steel Opponents 1 2 3 There are three bas
14. e or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance E Keep fingers out of the pinch point areas clearances between the doors and between the doors and cabinet are necessarily small be careful closing doors when children are in the area True Food Service Equipment Inc SAFETY INFORMATION DANGER RISK OF CHILD ENTRAPMENT PROPER DISPOSAL OF THE FREEZER Child entrapment and suffocation are not problems of the past Junked or abandoned freezer are still dangerous even if they will sit for just a few days If you are getting rid of your old freezer please follow the instructions below to help prevent accidents Before You Throw Away Your Old Refrigerator or Freezer E Take off the doors E Leave the shelves in place so that children may not easily climb inside Refrigerant Disposal Your old refrigerator may have a cooling system that uses Ozone Depleting chemicals If you are throwing away your old refrigerator make sure the refrigerant is removed for proper disposal by a qualified service technician If you intentionally release any refrigerants you can be subject to fines and imprisonment under provisions of the environmental regulations USE OF EXTENSION CORDS NEVER USE AN EXTENSION CORD TRUE will not warranty any refrigerator that has been connected to an extension cord True Food Service Equipment Inc SAFETY INFORMATION
15. er certain conditions we strongly recommend against the use of an adapter plug North America Use Only NEMA plugs TRUE uses these types of plugs If you do not have the right outlet have a certified electrician install the correct power source 115 60 1 NEMA 5 15R 7 IT LLE True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS INSTALLATION OPERATION INSTRUCTIONS OWNERSHIP To insure that your unit works properly from the Before you start to install your True unit carefully first day it must be installed properly We highly inspect it for freight damage If damage is recommend a trained refrigeration mechanic and discovered immediately file a claim with the electrician install your True equipment The cost of delivery freight carrier a professional installation is money well spent True is not responsible for damage incurred during shipment REQUIRED TOOLS E Adjustable Wrench E Phillips Head Screwdriver E Level UNCRATING Step 1 The following procedure is recommended for uncrating the unit A Remove the outer packaging cardboard and bubbles or styrofoam corners and clear plastic Inspect for concealed damage Again immediately file a claim with the freight carrier if there is damage B Move your unit as close to the final location as possible before removing the wooden skid C Remove door bracket on swing glass door models See image 1 2 Note Keys for coolers
16. h chlorides the industry is providing an ever increasing choice of non chloride cleaners If you are not sure of your cleaner s chloride content contact your cleaner supplier If they tell you that your present cleaner contains chlorides ask if they have an alternative Avoid cleaners containing quaternary salts as they can attack stainless steel Causing pitting and rusting Water Treatment To reduce deposits soften the hard water when possible Installation of certain filters can remove corrosive and distasteful elements Salts in a properly maintained water softener can be to your advantage Contact a treatment specialist if you are not sure of the proper water treatment Maintaining the cleanliness of your food equipment Use cleaners at recommended strength alkaline alkaline chlorinated or non chloride Avoid build up of hard stains by cleaning frequently When boiling water with your stainless steel equipment the single most likely cause of damage is chlorides in the water Heating any cleaners containing chlorides will have the same damaging effects Rinse When using chlorinated cleaners you must rinse and wipe dry immediately It is better to wipe standing cleaning agents and water as soon as possible Allow the stainless steel equipment to air dry Oxygen helps maintain the passivity film on stainless steel Hydrochloric acid Gnuriatic acid should never be used on stainless steel Regularly restore passivate stainless steel eT Te
17. ic things which can break down your stainless steel s passivity layer and allow corrosion to rear its ugly head Scratches from wire brushes scrapers and steel pads are just a few examples of items that can be abrasive to stainless steel s surface Deposits left on your stainless steel can leave spots You may have hard or soft water depending on what part of the country you live in Hard water can leave spots Hard water that is heated can leave deposits if left to sit too long These deposits can cause the passive layer to break down and rust your stainless steel All deposits left from food prep or service should be removed as soon as possible Chlorides are present in table salt food and water Household and industrial cleaners are the worst type of chlorides to use E 8 steps that can help prevent rust on stainless steel 1 13 Using the correct cleaning tools Use non abrasive tools when cleaning your stainless steel products The stainless steel s passive layer will not be harmed by soft cloths and plastic scouring pads Step 2 tells you how to find the polishing marks Cleaning along the polish lines Polishing lines or grain are visible on some stainless steels Always scrub parallel to visible lines on some stainless steels Use a plastic scouring pad or soft cloth when you cannot see the grain Use alkaline alkaline chlorinated or non chloride containing cleaners While many traditional cleaners are loaded wit
18. igerator Freezer Is NOT Covered By Warranty In Addition To Following Recommended installation Procedures You Must Run The Refrigerator Freezer 24 Hours Prior To Usage True Manufacturing Company Inc SAFETY INFORMATION How to Maintain Your DLE Freezer to Receive the Most Efficient and Successful Operation You have selected one of the finest commercial freezer units made It is manufactured under strict quality controls with only the best quality materials available Your TRUE freezer when properly maintained will give you many years of trouble free service WARNING Use this appliance for its intended purpose as described in this Owner Manual SAFETY PRECAUTIONS When using electrical appliances basic safety precautions should be followed including the following E This freezer must be properly installed and NOTE We strongly recommend that any located in accordance with the Installation servicing be performed by a qualified Instructions before it is used individual E Do not allow children to climb stand or hang E Unplug the freezer before cleaning and on the shelves in the freezer They could making repairs damage the freezer and seriously injure E Setting temperature controls to the 0 position themselves does not remove power to the evaporator fans E Do not touch the cold surfaces in the freezer compartment when hands are damp or wet Skin may stick to these extremely cold surfaces m Do not stor
19. n proper installation and start up in accordance with the instruction packet supplied with each TRUE unit TRUE s obligation under this warranty is limited to a period of one 1 year from the date of original installation or 15 months after shipment date from TRUE whichever occurs first Any part covered under this warranty that are determined by TRUE to have been defective within one 1 year of original installation or fifteen 15 months after shipment date from manufacturer whichever occurs first is limited to the repair or replacement including labor charges of defective parts or assemblies The labor warranty shall include standard straight time labor charges only and reasonable travel time as determined by TRUE ADDITIONAL FOUR YEAR COMPRESSOR WARRANTY In addition to the one 1 year warranty stated above TRUE warrants its hermetically and semi hermetically sealed compressor to be free from defects in both material and workmanship under normal and proper use and maintenance service for a period of four 4 additional years from the date of original installation but not to exceed five 5 years and three 3 months after shipment from the manufacturer Compressors determined by TRUE to have been defective within this extended time period will at TRUE s option be either repaired or replaced with a compressor or compressor parts of similar design and capacity The four 4 year extended compressor warranty applies only to hermetically and
20. or See image 2 Step 7 Replace cardboard cover Carefully slide compressor assembly back into position and replace bolts Step 8 Reinstall rear grill assembly onto unit Tighten all SCrews Step 9 Connect unit to power and check to see if compressor is running a 6 6 Oatnekateaans www truemfg com was SA O pgrge 2 060 0 89 g0 TST ed of YAYOI Dg 08 og o8 of oS of S090 oF og 08 08 08 08 08 08 8 08 68 OR Of 11 7 ITLL A True Food Service Equipment Inc MAINTENANCE CARE amp CLEANING IMPORTANT WARRANTY INFORMATION Condensers accumulate dirt and require cleaning every 30 days Dirty condensers result in compressor failure product loss and lost sales which are not covered by warranty If you keep the Condenser clean you will minimize your service expense and lower your electrical costs The Condenser requires scheduled cleaning every thirty days or as needed Air is pulled through the Condenser continuously along with dust lint grease etc A dirty Condenser can result in NON WARRANTEED part amp Compressor Failures Product Loss and Lost Sales Proper cleaning involves removing dust from the Condenser By using a soft brush or vacuuming the Condenser with a shop vac or using CO2 nitrogen or pressurized air If you cannot remove the
21. procedures for adjustment below NOTE Defrost timer will need to be set at current time of day before plugging unit into power supply The defrost times have been set from the factory If you want to change defrost times please read through the defrost timer instructions REQUIRED TOOLS e Phillips Screwdriver e 1 4 Nut Driver or Socket TUC TWT Defrost Timer Location Defrost timer can be found by removing the rear screen Setting the timer UNPLUG UNIT FROM POWER SUPPLY Turn the clock outer dial clock wise until the correct time of day on the outer dial is aligned with the marker of the inner dial See image 2 8 acce WWW truemfg cOm 0066 True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS Adjusting The Defrost Timer time initiated time terminated Your True equipment contains a defrost system that is time initiated and time terminated While True requires a minimum 3 defrost periods not to exceed 30 minutes the procedure on this page should be followed to customize your specific needs Notice If timer is not set for a minimum of 3 defrost per day for 30 minutes each the coil may develop excessive frost This may lead to system failure and product loss which is not covered under warranty The following procedure may be followed to customize your needs High usage high temperature and high humidity may require 4 defrost settings per day WARN
22. rmal and proper use and maintenance service as specified by True This warranty is limited to the cabinet only True assumes no liability for remote condensing units 15 vececceeeeee WWWw trueMfE COM 0066 15
23. rocedure Step 3 Securing Castors and Legs To obtain maximum strength and stability of the unit it is important that you make sure each castor is secure Legs are hand tightened securely against the lower rail assembly The bearing race on the castor of the top edge of the leg must make firm contact with the rail Unit leveling Four leveling shims have been provided for leveling castored units positioned on uneven floors Shims must be positioned between rail end and bearing race True requires a four shim limit to each individual castor Thread castor into the underside of cabinet frame The end of the leg is adjustable to easy leveling 5 For leveling insert the shim between the castor and frame rail tighten the castor into place A Turn the bearing race counter clockwise until the cabinet is level Level front to back and side to side diagonally B Install the desired number of shims making sure the slot of the shim is in contact with the threaded stem of the castor C If more than one shim is used turn the slot at a 90 angle so they are not in line D Turn the bearing race clockwise to tighten and secure the castor by tightening the anchoring bolt with a 3 4 inch open end wrench or the tool provided CAUTION To avoid damage to lower rail assembly slowly raise unit to upright position Thread leg into cabinet bottom frame rail Use the tool provided to j X Bearing R
24. semi hermetically sealed parts of the compressor and does not apply to any other parts or components including but not limited to cabinet paint finish temperature control refrigerant metering device driers motor starting equipment fan assembly or any other electrical component etcetera 404A 134A COMPRESSOR WARRANTY The four year compressor warranty detailed above will be voided if the following procedure is not carefully adhered to 1 This system contains R404A or R134A refrigerant and polyol ester lubricant The polyol ester lubricant has rapid moisture absorbing qualities If long exposure to the ambient conditions occur the lubricant must be removed and replaced with new For oil amounts and specifications please call True technical service department 800 325 6152 Failure to comply with recommended lubricant specification will void the compressor warranty 2 Drier replacement is very important and must be changed when a system is opened for servicing A drier using XH 7 desiccant or an exact replacement solid core drier must be used The new drier must also be the same capacity as the drier being replaced 3 Micron level vacuums must be achieved to insure low moisture levels in the system 500 microns or lower must be obtained WARRANTY CLAIMS All claims for labor or parts must be made directly through TRUE All claims should include model number of the unit the serial number of the cabinet proof of purchase date of installation
Download Pdf Manuals
Related Search