Home

RCA VR646HF VCR User Manual

1. signals you may need to Auto Channel Search again Exit 3 Press 1 to display the AUTO CHANNEL SEARCH menu 10 SETTING UP THE VCR AUTO CHANNEL SEARCH What type of signal are you using 1 Cable TV 2 Antenna 3 gt Detect Automatically 0 Cancel 4 Select one of the three AUTO CHANNEL SEARCH options e Cable TV searches for cable channels e Antenna searches for local broadcast stations e Detect Automatically will make this decision for you AUTO CHANNEL SEARCH Now scanning channel 14 Press any key to cancel The VCR begins scanning for the available channels this takes about one to two minutes When the scan is complete the VCR tunes to the lowest channel number At this point pressing CHAN up or down on the remote control or VCR should only select the active channels To Change the Signal Type 1 Press MENU to display the VCR MAIN MENU 2 Press 4 to display the CHANNELS menu 3 Press 3 to change the Signal Type between CABLE and ANTENNA Adding or Removing Channels You may want to add or remove channels after you Auto Channel Search especially if some of the channels have weak Detect Automatically A strong cable or antenna signal in your area may cause Auto Detect to mis detect If this should happen select 1 or 2 for the system you have 11 12 SETTING UP THE VCR signals or you don t want to watch them 1 Press MENU to display the VCR MAIN MENU 2 Press 4 to disp
2. VR646HF SAFETY INFORMATION WARNING VW TSIN GME TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE To reduce risk of fire or REFER SERVICING TO QUALIFIED SERVICE PERSONNEL DO NOT OPEN shock hazard do not This symbol indicates dangerous expose this product to This symbol indicates voltage inside the product that rain or moisture important instructions presents a risk of electric shock or accompanying the product personal injury Ca utions Caution To reduce the risk of electric shock match the wide blade of plug to wide L slot and fully insert E T Attention Pour viter les chocs lectriques introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusq au fond Refer to the identification rating label located on the back panel of your product for its proper operating voltage FCC Regulations state that unauthorized changes or modifications to this equipment may void the user s authority to operate it Cable TV Installer This reminder is provided to call your attention to Article 820 40 of the National Electrical Code Section 54 of the Canadian Electrical Code Part 1 which provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical Care and Cleaning Use a soft cl
3. e Press 1 to Go To Movie The following screen appears with a blue background MOVIE ADVANCE What type of tape is this 1 Purchased Rented Movie 2 Home Recording 3 Other Press CLEAR to cancel When the movie is found the following screen is displayed MOVIE ADVANCE The movie is ready Press PLAY to start Press STOP to cancel This display will time out after a few minutes and the VCR will enter the Stop mode e Press 2 to Go To Preview The following screen appears with a video background Searching for preview Press SEARCH to reverse Press STOP to cancel When a preview is detected the VCR cues it and begins playing Press SEARCH for next Preview Search Note Any time during the preview search mode pressing SEARCH will reverse the search direction 44 OTHER FEATURES PICTURE SEARCH OPTIONS The most basic way to search during playback is using the FORWARD or REVERSE buttons on the remote This section contains several other options available for searching a tape FORWARD AND REVERSE SEARCH You can search a tape during playback Sound is turned off during picture search Search works well for tapes recorded at either the SP or SLP speed 1 Press FORWARD to search forward or REVERSE to search in reverse 2 Press FORWARD or REVERSE again or press PLAY to return to normal playback SLOW MOTION You can view a tape during play or play pause using slow motion Slow motio
4. 38 8 f 3 CH 4 Switch AUDIO VIDEO OUT Jacks When using the ANT IN and RF OUT jacks to connect your VCR tune your TV to channel 3 or 4 The 3 CH 4 switch on the back of the VCR determines which TV channel is used to see the VCR s output When using the AUDIO VIDEO jacks to connect your VCR tune your TV to the TV s Video Input Channel with the TV and INPUT buttons on your remote control For more information about selecting your video input channel see page 68 FIRST THINGS FIRST STEP 8 ACCESS THE MENUS The MENU and number buttons let you access select and change your VCR s preferences For example to select a different preferred on screen language than the one you selected during the initial set up do the following 1 Press MENU to display the VCR MAIN MENU VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 7 to display the LANGUAGE menu LANGUAGE Select a language 1 gt English 2 Espanol 3 Francais Press MENU to continue 3 On the remote control press 1 for English 2 for Espa ol Spanish or 3 for Fran ais French All other on screen menus are worked within similar ways using the remote control to follow on screen instructions See Additional Set Up Features in the next section for detailed information about accessing menus NEXT SECTION LEARN VCR S MENUS Now that you understand how to move aroun
5. Code WN 0 Exit 3 Select 1 to Create a New Program How often should this program record One time Daily every day Weekdays M F Weekly once per week Timer Recording Information The Clock must be set correctly Cancel Insert a tape with the safety tab in place and enough tape to record 4 Select how often you want the program to record the program PROGRAMS OVERLAP appears if you have entered two programs whose times overlap Program 1 One time Channel Start Time End Time Sat taal Start Date Tape Speed SLP The TIMER indicator appears in the display when you turn off the VCR and a timer recording has been set It flashes if there is no tape in the VCR Press MENU to cancel 5 Enter the data for the program with the number buttons When recording from a cable box or satellite receiver turn on that unit and tune it to the channel you want to record before the recording is to begin The VCR channel should be set to the cable box s output channel usually Channel 3 or 4 The data includes the channel number press INPUT to select the line input start time and end time including AM or PM The start date is automatically entered based on the VCR clock The date and or speed can be changed when flashing 6 Review the information to make sure it is correct and then 29 RECORDING press MENU to save Program 1 One Time Program 1 has b
6. These jacks are used for most audio video connections between components The VCR s AUDIO VIDEO jacks are color coded yellow for video and red and white for audio If your TV only has one input for audio you may need a Y adapter to hear sound from both channels a2 CONNECTIONS CHOOSING A VCR CONNECTION There are several different ways to connect your VCR depending on whether or not you have cable service and if you have a cable box and whether some of the channels are scrambled well you get the picture Three connections are described in this section and one of them should provide you with a VCR connection that works e TV with RF Jack Only e TV with Audio Video Jacks e TV with Audio Video Jacks and Cable Box to Unscramble Pay Channels Only If you need to connect additional components not shown in the diagrams here and are unsure of how to connect them refer to the instruction manual that came with that particular component ADVANTAGES OF AUDIO VIDEO CABLE CONNECTIONS Using a simple coaxial cable connection gives you good picture quality If your television has AUDIO VIDEO jacks though it is highly recommended that you use them to get even better picture quality and Hi Fi stereo sound when recording and playing back videotapes These connections give you more convenient operation by not having to share the TV s antenna signal If you are having a hard time understanding the TV s Video Input Channel refer to
7. for cable box e 2 audio video cables To connect 1 Connect cables as shown 2 Return to First Things First then follow the steps Using This Connection Tune your TV to its Video Input Channel see page 68 for more information Use of TVeVCR button is not required To play a tape 1 Insert a tape 2 If necessary press PLAY CABLE CABLE BOX OR scene To record one program and watch another 1 Begin recording a program using one of the recording features 2 Select a different channel on the TV CABLE ANTENNA 55 CONNECTIONS TV WITH AUDIO VIDEO JACKS AND CABLE BOX TO UNSCRAMBLE PAY CHANNELS ONLY This connection assumes e You are using a cable box only to unscramble premium channels e Your TV has audio video input jacks This connection provides e Hi Fi stereo sound playback from the VCR e Recording a scrambled or unscrambled channel through the cable box while watching an unscrambled channel To use this connection you must have e 3 coaxial cables e 2 audio video cables e 1 splitter All scrambled channels must be viewed through the VCR To connect 1 Connect cables as shown 2 Return to First Things First then follow the steps Using This Connection Tune your TV to its Video Input Channel see page 68 for more information Use of TVeVCR button is not required To play a tape 1 Insert a tape 2 If necessary press PL
8. Cassette ejected e FF Fast forwarding e HI VCR turned on and BYE VCR turned off e PLAY In playback flashes during play pause and slow e REC Recording and RECP For record pause or pause mode e REW Rewinding e RO 30 Express recording in progress e SAFE Pro Tect Plus feature turned on e STILL Play pause e SCH and SCH Forward or reverse search e SP and SLP Tape speed e STOP Tape is stopped Timer Indicator Lights during an express or timer tecording or when the VCR is set for a timer recording and turned off Flashes when a timer recording is set and there is no tape in the VCR VCR Indicator Applies only if the VCR Viewing Channel is 3 or 4 Pess the TV VCR button to turn on or off e VCR indicator on Picture from VCR e VCR indicator off Picture from TV channel 59 APPENDIX REFERENCE BACK PANEL 9 L169 iunio RF RIO Q 3cH 4 3 CH 4 Switch Selects the channel to which you will tune the TV to see the VCR picture if you connect the VCR using one of the basic hookups AUDIO R and L and VIDEO IN Jacks Receives signals from another component like a VCR or camcorder when it is connected to these jacks Use INPUT on the remote to select L1 to record from these jacks AUDIO R and L and VIDEO OUT Jacks Sends signals from VCR to another component like a TV or VCR when it is connected to these jacks ANT IN Jack Receives a signal from an antenna or ca
9. Plus channel list for your viewing area or contact your cable company Using the list may save you some time SETTING UP THE VCR VCR Plus SYSTEM WORKSHEET hatin or VCR Plus System Channel bearing a e TV Channel Number You Receive the Station Name Station On Two Digit VCR Plus System Channel Numbers for Cable TV Canadian List 67 Allarcom Pay Television Superchannel 44 Arts amp Entertainment 72 Cable News Network Headline News 61 Cable News Network 70 Canadian Home Shopping Network 56 Canal Famille 69 Cathay International Television Inc 68 Chinavision Canada Corp 60 Country Music Television 63 Family Channel 62 First Choice 96 First Choice Two 97 First Choice Three 99 First Choice Four 90 House of Commons 91 La Chaine Francaise 51 The Learning Channel 65 MeteoMedia The Weather Network 48 MuchMusic Network 55 MusiquePlus 52 Nashville Network 73 Newsworld CBC 53 Le Reseau des Sports 43 The Sports Network 64 Super Ecran 37 Super Ecran B 98 Super Ecran C 66 Telatino Network 46 TV5 Montreal 92 Viewer s Choice 1 93 Viewer s Choice 2 94 Viewer s Choice 3 95 Viewer s Choice 4 71 Vision TV Canada s Faith Network 38 Youth TV Canada Inc Check your local or cable listings for the channel number you receive this station on Check your local listings for broadcast or VCR Plus channel number assigned 17 18 SETTING UP THE VCR ADDITIONAL SET
10. The VCR has automatic tracking which adjusts the picture when playing back a tape recorded on another VCR Automatic tracking is turned on whenever a tape is inserted or the VCR s power is turned on VCR BASICS TAPE EJECT Press STOPeEJECT on the VCR STOP on remote for a few seconds when it is stopped to eject the tape A tape can be ejected even when the VCR is off RECORDING If you want to record something that you re watching you can use basic recording For more detailed information refer to the Recording section starting on the next page 1 Set the tape speed by pressing TAPE SPEED on the VCR SPEED on the remote 2 Press the RECORD button to begin recording 3 Press STOP to stop recording If you just want to pause the recording for a short time such as during a commercial press PAUSE instead of STOP e For more information about in depth recording features refer to the next section CHECK THE SAFETY TAB No matter which recording option you use you need to make sure there is a tape in the VCR and that the tape s safety tab is in place You cannot record on a tape with the safety tab removed If the safety tab is removed and you want to record over it simply cover the hole with vinyl tape Rccf Es ak E Safety Tab Tape Speeds SP Standard Play Gives the best quality recording but fewer programs can be recorded on the tape Special effects such as pau
11. UP FEATURES IN THE PREFERENCES MENU The features in this section are all accessed through the PREFERENCES menu 1 Press MENU to display the VCR MAIN MENU VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 5 to display the PREFERENCES menu PREFERENCES Remote Control VCR1 Auto Play ON EnergySaver 2 00 Front Panel AUTO Tape Speed SLP Commercial Advance Exit Now you are ready to select an item from the menu to set up REMOTE VCR1 VCR2 OPTION If you own a compatible RCA GE or ProScan remote that has a VCR2 VCR2eLD or VCR2eDVD button this feature allows you to set this VCR to respond to that button In the PREFERENCES menu press 1 to select REMOTE CONTROL With the compatible remote control press the VCR2 VCR2eLD or VCR2eDVD button to change which remote controls the VCR PREFERENCES PREFERENCES Press VCR2 to Change Remote Control 2 Auto Play ON Auto Play EnergySaver 2 00 EnergySaver Front Panel AUTO Front Panel Tape Speed SLP Tape Speed Commercial Advance Commercial Advance 0 Exit Exit The VCR will only respond to the compatible remote s VCR2 VCR2eLD or VCR2 DVD button If the PREFERENCES setting is Remote Control Option Changing the remote option to VCR2 disables the remote that came with your VCR SETTING UP THE VCR changed to VCR2 the remote that came with your VCR will no longer control it To
12. VCR is stopped Searches the picture forward during playback Starts slow motion during play pause and increases slow motion speed PLAY PAUSE Plays a tape Pauses action for viewing during playback Pauses recording to prevent recording of unwanted scenes POWER Turns the VCR on or off RECORD Starts VCR recording Used for express recording Remote Sensor Receives signals from the remote control Aim the remote at this sensor REV Rewinds the tape when the VCR is stopped Searches the picture in reverse during playback Starts slow motion during play pause and decreases slow motion speed TAPE SPEED Selects a recording speed either SP or SLP STOPeEJECT Stops the normal functions such as record playback rewind fast forward or pause Ejects the tape when the VCR is stopped TVeVCR Switches the picture signal so that it either comes from the VCR or the cable antenna system APPENDIX REFERENCE DISPLAY PANEL Time Channel Number Line Input Indicator L1 or L2 Tape Speed Indicator or Status Indicator Channel Number or Line Input Indicator The channel number appears when the VCR is tuned to a channel The line indicator L1 or L2 appears when the VCRS line input is selected Select L1 to record from the back jacks L2 to record from the front jacks Time The current time appears Only an AM indicator appears with the time There is no indicator for PM Status Indicators Show what the VCR is doing e EJCT Eject
13. cables and keep them away from the audio video cables as much as possible e Make sure all antennas and cables are properly grounded Refer to the Safety Tips sheet packed with 6 OTHER FEATURES your unit Protect Your Components from Overheating 7 CONNECTIONS a 3 Bence 51 e Do not block ventilation holes in any of the components Arrange the components so that air can circulate freely Do not stack components Q REFERENCE e Allow adequate ventilation when placing your components in a stand e Place an amplifier or satellite receiver on the top shelf of the stand so heated air rising from it will not flow around other components CONNECTIONS CONNECTING YOUR VCR Refer to these pages to help you connect your VCR JACKS AND CABLES RF Jacks and Coaxial Cables F type The RF jacks provide good picture and mono sound quality and A must be used if audio video connections are not available for your TV RF Jack These jacks are required for antenna or cable TV connections The RF jacks on the VCR are labeled ANT IN and RF OUT The coaxial cable supplied with your VCR is used to connect the VCR s RF OUT jack and your TV s antenna input Audio Video Jacks and Cables RCA type The AUDIO VIDEO jacks provide very good picture quality and oO stereo sound and can be used if your TV has audio video input jacks For more information about the TV s Video Input Channel see page 68 Audio Video Jack
14. change the setting back to VCR1 so the remote which came with your VCR can control the unit use the compatible remote to display the PREFERENCES menu press 1 and then VCR on this VCR s remote AUTO PLAY This feature allows the VCR to automatically start playing a tape when inserting a tape with the safety tab removed In the PREFERENCES menu press 2 to switch between ON and OFF e Select ON if you want a tape with its safety tab removed to start playing automatically when inserted in the VCR e Select OFF if you do not want a tape with its safety tab removed to start playing automatically ENERGYSAVER By default this VCR automatically turns off after two hours of inactivity To change the time delay or to disable the feature Press 3 in the PREFERENCES menu to switch between ON and OFF e OFF means the VCR will remain turned on until you shut it off e 1 00 2 00 or 3 00 means the VCR turns off after one two or three hours of inactivity respectively Thirty seconds before shutting off the VCR will warn you with a screen reading The VCR will turn off in 30 seconds Press any key to cancel If you use the VCR s tuner instead of your TV to tune channels you may want to turn this feature off FRONT PANEL BRIGHTNESS VCR DISPLAY You can change the brightness level of the fluorescent display panel on the front of the VCR In the PREFERENCES menu press 4 to switch between the options PREFERENCES Remote Co
15. e Cleaning of video audio heads e Batteries e AVCR that has been modified or incorporated into other products or is used for institutional or other commercial purposes e AVCR purchased or serviced outside the USA e Acts of God such as but not limited to lightning damage Product Registration e Please complete and mail the Product Registration Card packed with your VCR It will make it easier to contact you should it ever be necessary The return of the card is not required for warranty coverage How state law relates to this warranty e This warranty gives you specific legal rights and you also may have other rights that vary from state to state If you purchased your VCR outside the United States e This warranty does not apply Contact your dealer for warranty information 69 INDEX A Adding removing channels 12 ANT IN jack 5 54 Audio playing back 32 recording 31 Audio Video A V jacks 5 22 31 32 52 54 Auto channel search 10 Auto play feature 19 Automatic rewind 24 Automatic tracking 23 Batteries installing in the remote 4 Broadcast stereo recording SAP 31 C Cable box setup 9 Cables positioning 45 Channel 3 4 switch 5 54 CHANNEL buttons 22 Channel List 28 Channel VCR viewing 5 CHANNELeTRACKING button 52 Channels adding removing 12 CHANNELS menu 9 Cleaning the VCR 61 CLEAR button 22 Clearing programs 30 COMMERCIAL ADVANCE 33 34 35 36 questions and answers 60 70 Connec
16. information Tape plays back in slow motion e Press PLAY to return to normal playback Cannot select channels over 69 e Cable channels over 69 can only be selected if Signal Type CABLE ANTENNA feature is set to CABLE Cassette with safety tab removed does not start to play automatically e Check to make sure the AUTO PLAY ON OFF feature is set to ON 63 64 APPENDIX REFERENCE Timer indicator flashes e The clock is not set e Check to make sure there is a cassette in the VCR when a timer recording is set Time counter disappears during searching e This is normal On screen menus appear in English French or Spanish e Check LANGUAGE feature No stereo sound during playback e Check to make sure the TAPE PLAYBACK feature is set to Hi Fi to hear stereo sound during playback The tape you are paying must be recorded in Hi Fi in order to use the HI FI feature e Must use the AUDIO VIDEO jacks on the back of the VCR to hear stereo sound Stereo audio too noisy e Stereo signal is weak Set reception STEREO SAP MONO feature to MONO e Press one of the TRACKING up or down buttons to minimize the noise Index and Go To search features do not operate e Check to see if MOVIE gt gt ADVANCE feature is activated Cannot access MOVIE gt gt ADVANCE feature e Cassette must have safety tab removed and be recorded in SP speed e Home Recording was selected for the tape type in the menu Eject cass
17. the remote s back panel Match the positive and negative ends of each battery to the diagram inside the battery compartment 3 Replace the cover STEP 3 CONNECT YOUR VCR If you connect your VCR to your home antenna or cable system and then to your TV use the VCR s ANT IN and RF OUT jacks for a good signal as shown to the right If you have a TV with AUDIO VIDEO jacks use the jacks for a better connection Refer to the section Connections toward the back of the manual for additional connection options CABLE CABLE BOX OR m STEP 4 PLUG IN THE VCR Your VCR s power cord has a plastic band strung through the blades Remove plastic band before plugging the cord into the power outlet To remove band cut with a pair of scissors OUT IN ANT IN and pull it free of the blades Once the plastic is removed match _Oyweo the wide blade of the power cord to the wide slot in the AC l 5 Auno mFout outlet Be sure to insert the plug completely 6 mS STEP 5 TUNE THE TV Tune the TV to the VCR viewing channel The VCR viewing channel is channel 3 or 4 or the TV s video input CABLE ANTENNA FIRST THINGS FIRST e If you connect your VCR using the ANT IN and RF OUT connectors with RF coaxial cable set the 3 CH 4 switch to channel 3 or channel 4 the channel you want to use on your TV e If you connect your VCR using the AUDIO VIDEO jacks with audio video cables s
18. 30 seconds of recorded material during playback Each press advances the tape an additional 30 seconds up to five minutes SPEED Selects a recording speed SP or SLP STOP Stops the current VCR function such as record playback rewind or fast forward To eject a tape press and hold the STOP button for three seconds while in STOP mode TRACKING Up or Down Lets you manually reduce the streaks that may appear on the picture during play slow motion or pause Reduces picture jitter during stop action playback TVeVCR Switches the picture signal so that it either comes from the VCR or cable antenna system TV FUNCTION BUTTONS CHAN Up or Down Selects next higher or lower channel in the TV s channel memory CLEAR Removes menus or status displays from the screen GO BACK Switches between two channels Select one channel and then select another using the number buttons Press GO BACK to switch between the two channels INFO Shows the TV s status displays on the TV screen INPUT Selects between the TV s input channel or tuner Press to see the VCR signal if you connected your VCR using the AUDIO VIDEO jacks MUTE Reduces volume to minimum level TV Buttons The TV buttons may not control all features of all models of RCA GE or PROSCAN TVs If you have trouble getting a picture on the TV screen refer to How to Find Your TV s Video Input Channel on page 68 or the Troubleshooting section starting on pa
19. AY To record a scrambled or unscrambled program and watch another unscrambled program 1 Begin recording a scrambled or unscrambled program through the cable box using one of the recording features 2 Select an unscrambled channel on the TV CABLE ANTENNA 56 APPENDIX REFERENCE This section gives you some additional information about the VCR including a description of the unit s controls and displays You will also find the section Troubleshooting Tips and a question and answer section about COMMERCIAL gt gt ADVANCE in this Appendix These areas might help resolve some of those simple problems Finally this section of the manual also contains your warranty information FIRST THINGS FIRST D SETTING UP THE VCR 3 vcr Basics RECORDING 5 PROGRAM THE REMOTE 6 OTHER FEATURES 7 CONNECTIONS Q REFERENCE lt lt lt lt lt lt lt lt lt lt Vi N APPENDIX REFERENCE 58 FRONT PANEL Remote Sensor AUDIO LEFT MONO and RIGHT and VIDEO INPUT Jacks Receives signals from another component like a VCR or camcorder when it is connected to these jacks Use INPUT on the remote to select L2 to record from these jacks CHANNEL TRACKING Up or Down Selects next higher or lower channel in the VCR s channel memory Adjusts tracking when a tape is playing Press both together to recenter tracking FWD Forwards the tape when the
20. Add Remove Channels Signal Type CABLE VCR Plus Channel List Cable Box Setup Exit 3 Press 4 to display the VCR PLUS CHANNEL LIST menu VCR Channel My Channel 4 Use CH to select Press 0 9 to change Press MENU to save 4 Enter the data following the on screen directions using your worksheet VCR Channel My Channel 5 46 4 on 3 gt gt gt 23 2 1 Use CH to select Press 0 9 to change Press MENU to save Screen shown is for an example only VCR Plus system is a registered trademark of Gemstar Development Corporation The VCR Plus system is manufactured under the license from Gemstar Development Corporation Two Digit VCR Plus System Channel Numbers for Cable TV USA List American Movie Classics Arts amp Entertainment Black Entertainment Bravo Cable News Network Cinemax Cinemax 2 The Discovery Channel The Disney Channel Entertainment Television ESPN Sports Network The Family Channel Home Box Office Home Box Office 2 Home Box Office 3 The Learning Channel Lifetime The Movie Channel Music Television The Nashville Network Nickelodeon Nostalgia Television Quality Value Cable Showtime Showtime 2 Sports Channel Turner Network Television USA Network Video Hits 1 Viewer s Choice 1 Viewer s Choice 2 WGN Chicago WTBS Atlanta WWOR New York See next page for Canadian List VCR Plus System Channel List Refer to your local television list for a complete VCR
21. D AUDIO PROGRAM Some TV programs are broadcast with stereo audio or SAP Second Audio Program 1 Turn on the TV and tune it to the VCR viewing channel either 3 4 or TV s video input Insert a tape with safety tab in place If your VCR viewing channel is 3 or 4 make sure the VCR indicator appears in the VCR s display panel If not press TVeVCR to turn it on 4 Use the SPEED button on the remote to select a recording speed The tape speed indicator appears on the TV screen RECORDING 5 Select the channel or line input to be recorded 6 Set the Reception STEREO MONO SAP feature for the type of audio you want to record See Other Features section AUDIO 1 Reception STEREO 2 Tape Playback HI FI Video Input Channel Explained If you re having trouble understanding the TV s Video Input Channel turn to page 68 for more information 7 Press RECORD to start recording 8 Press STOP when you are finished RECORDING AUDIO ONLY You can record audio only from another audio source connected to the AUDIO IN R and L jacks on the back or front of the VCR 1 Press the INPUT button on the remote to select the line input L1 or L2 Select L1 to record from the back jacks or L2 to record from the front jacks The VCR will record audio from the audio equipment connected to the AUDIO IN jacks 2 Use TAPE SPEED on the VCR SPEED on the remote to select THe PECORSING SPEER Recording audio only wil
22. ERCIAL gt ADVANCE marked recordings work in non Commercial Advance VCRs A COMMERCIAL gt ADVANCE marked recording will play in a non commercial advance VCR but commercials will not automatically be skipped APPENDIX REFERENCE SPECIFICATIONS Format Record Playback System Video Signal System Antenna Tuner Type synthesis Power Requirement Power Consumption Dimensions Weight Storage Temperature Range Operating Temperature Range VHS Video 4 head Audio Stereo record playback system EIA standard NTSC color 75 ohm external VHF UHF combined antenna terminal USA 181 channels capability 125 cable channels Canada 178 channels capability 122 cable channels AutoProgramming frequency 120V AC 60 Hz 17 watts 3 54 inches high 90 mm 14 96 inches wide 380 mm 10 94 inches deep 278 mm 7 9 pounds 3 6 Kg 22 F to 149 F 30 C to 65 C 41 F to 104 F 5 C to 40 C Check your cable company s compatibility requirements CLEANING THE VCR Use a soft cloth or dusting attachment of your vacuum cleaner to dust your VCR Remove dust from the ventilation holes on the cabinet Plastic surfaces are easily scratched and can be marred by alcohol and various solvents Avoid excessive use of oil based furniture polishes since the materials used in the cabinet will accumulate more dust We recommend using a nonabrasive antistatic cleaner and polishe
23. MENU VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 5 to display the PREFERENCES menu COMMERCIAL ADVANCE is a registered trademark of SRT Inc 40 OTHER FEATURES PREFERENCES Remote Control VCR1 Auto Play ON EnergySaver 2 00 Front Panel AUTO Tape Speed SLP Commercial Advance Exit 3 Press 6 to display the COMMERCIAL ADVANCE menu COMMERCIAL ADVANCE Marking Playback Display Now you can select one of the COMMERCIAL gt gt ADVANCE features COMMERCIAL gt gt ADVANCE Marking Press 1 to turn commercial marking ON or OFF e Select ON and the VCR will mark commercials within approximately 30 seconds for the following types of recording Timer Timer with VCR Plus or Express Recording Sets the VCR to automatically mark commercials after the power is tuned off Recording Allows the VCR to prompt you to mark the commercials when you ve stop the recording The VCR is waiting to mark commercials in the program you recorded 1 Mark them now 2 Mark them Later 3 Don t mark commercials The VCR will begin marking in 30 seconds e Select OFF and the VCR will not mark the commercials 41 OTHER FEATURES COMMERCIAL gt gt ADVANCE Playback Press 2 to switch between Playback AUTO and MANUAL e Select AUTO to have the VCR automatically advance through the blocks of marked commercials It works with mo
24. PlusCode Number from TV Listing If you receive all channels through your cable box on Channel 3 or 4 you must use the regular Timer Recording method to record programs Press MENU to cancel RECORDING 3 Enter the VCR PlusCode programming number shown in your local television guide VCR PLUS Enter PlusCode Number from TV Listing 12876 Press CLEAR to erase Press MENU when done 4 Press MENU to enter the PlusCode system number How often should this program record 1 One time 2 Daily every day 3 Weekdays M F 4 Weekly once per week 0 Cancel 5 Indicate how often you want the program to be recorded Program 1 One time Channel 03 Cable Start Time 08 00 PM End Time 09 30 PM Start Date 11 18 99 Thu Tape Speed SLP Press CLEAR to adjust Press MENU to save 6 Change the recording speed with the SPEED button on the remote or the program end time with the CLEAR button on the remote if necessary Changing the end time comes in handy when you are recording a program such as a sporting event that may exceed the scheduled broadcast time 7 Press MENU to save the program Program 1 has been saved Remember to insert a recordable tape and turn the VCR off before the program start time Remember to leave your cable box on and tuned to the desired channel PlusCode is a registered trademark of the Gemstar Development Corporation The VCR Plus system is manufact
25. R records the same audio on both Hi Fi and linear tracks on the tape Hi Fi sound is recorded on a separate left and right stereo channels Monaural sound is recorded on the linear track Press 2 to switch between tape playback HI FI LINEAR and MIX To enjoy Hi Fi sound connect your VCR to a stereo television or amplifier receiver using the AUDIO VIDEO jacks The Tape Playback feature lets you select which audio you use during playback e Select HI FI to play back sound recorded on the Hi Fi track and for normal use e Select LINEAR to play back sound recorded on a linear monaural track such as a Second Audio Program SAP or a dubbed voice e Select MIX to play back the sound recorded on both the linear and Hi Fi tracks sound on sound 50O CONNECTIONS THINGS TO KNOW BEFORE CONNECTING COMPONENTS FIRST THINGS FIRST Protect Your Components from Power Surges e Connect all components before plugging any power 2 SETTING UP THE VCR cords into the wall outlet e Always turn off the TV and other components before you connect or disconnect any cables 3 vcr Basics Position Cables Correctly to Avoid Audio Hum or A lt lt lt Interference e Insert all cable plugs firmly into their jacks A Ravaeltiplinie e Place the audio video cables to the sides of the TV s back panel instead of straight down the middle after y you connect your components 5 PROGRAM THE REMOTE e Try not to coil any twin lead
26. Select a language 1 gt English 2 Espanol 3 Francais Press MENU to continue 3 Select English Espa ol Spanish or Fran ais French by pressing the appropriate number on the remote control s key pad CABLE BOX SETUP This setup applies only when all channels are received through On Screen Menus Not all the VCR screens are shown in this manual when explaining the features SETTING UP THE VCR a cable box In this case the VCR will automatically enter the channel used to view cable box programming Your VCR will use this channel for all future timer recordings 1 Press MENU to display the VCR MAIN MENU VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 4 to display the CHANNELS menu CHANNELS Auto Channel Search Add Remove Channels Signal Type CABLE VCR Plus Channel List Cable Box Setup Exit 3 Press 5 to display CABLE BOX SETUP Then select one of the three choices CABLE BOX SETUP Do you use your cable box to receive ALL channels or only SOME channels 1 ALL channels 2 Only SOME channels 3 Cancel setup 4 If you selected ALL channels enter the output channel of your cable box usually 03 or 04 or press INPUT for the VCR s video line input if you use AUDIO VIDEO jacks Then press MENU Cable Box Setup CABLE BOX SETUP On what channel does the VCR receive signals from the cable box Cusually 3 4 or V
27. TRACKING Your VCR has automatic tracking which removes interference like streaks or snow from the picture Automatic tracking is automatically activated when you insert a tape or turn on the VCR Occasionally you may need to manually adjust tracking especially if the tape was recorded on a different VCR Just use the TRACKING buttons to reduce the distortion You can also use tracking when you pause a tape to reduce jittering of the picture When you manually adjust the picture automatic tracking is turned off To turn automatic tracking back on press both TRACKING buttons on the front of the VCR at the same time or eject the tape and re insert it Tracking has no effect during recording only playback If you insert a pre recorded tape with the safety tab removed Index and Go To searches are not available 47 OTHER FEATURES PRO TECT PLUS LOCKING FEATURE To disable the usage of the VCR or to protect your timer Locking Your VCR recordings you can lock the VCR so that the buttons on the VCR or remote won t work If a timer recording is programmed make sure your VCR is turned off e To Lock Press and hold the VCR button on the remote Locking your VCR prevents the VCR for approximately six seconds SAFE appears from being accidentally turned on e To Lock While a Timer Recording is in Progress Press and hold the VCR button on the remote for approximately six seconds e To Unlock Press and hold
28. ake sure the tape is of good quality and not worn out 61 62 APPENDIX REFERENCE Time counter not working or time counter not working in search modes The time counter does not advance during unrecorded portions of tape When an unrecorded segment of tape is encountered the time counter will hold its count until recorded material is detected again A minus will appear in front of the time if you rewind the tape farther back than a counter reading of 0 00 00 The time counter disappears during search this is normal Will not record or play Check to make sure there is a tape in the VCR Try ejecting and reinserting the cassette Check to make sure the tape is not broken Check to make sure the VCR is not in pause mode Press PAUSE or PLAY to return to normal playback Check the ProTect Plus feature Rewind does not operate Check to make sure the tape is not already rewound VCR Plus programming system or timer recording not made or wrong program recorded Check to make sure the correct VCR Plus code is entered Check to make sure the cable box or satellite receiver was turned on when recording was to begin Check to make sure the program was entered correctly wrong channel or times Power interruption Reset the clock Check to see if time and date are correct including AM PM Check to make sure the program did not exceed the tape s length or the tape was not rewound beforehand Check t
29. ape speed a 3 minute commercial break is scanned through in approximately 8 12 seconds In SP it takes about 25 35 seconds Are commercials still recorded if want to watch them Yes The recorded program including commercials can be viewed by setting the Playback feature to MANUAL What if the VCR scans forward through part of my program Simply rewind the tape to just before the skipped segment and press PLAY to view the program Once a recording has been marked does COMMERCIAL gt ADVANCE work each time the tape is played Yes If the Playback feature is set to AUTO the marked commercials should be skipped each time the tape is played in a COMMERCIALP gt ADVANCE VCR After marking commercials is the tape left at the beginning or end of the recording The tape is left at the end of the recording so it is in position to begin additional programmed recordings Does the marking process interfere with other programmed recordings No If two or more recordings are programmed together without sufficient time to mark the first recording marking will take place after all recordings have completed What happens if the marking process is interrupted Marking can be interrupted to allow use of the VCR Marking will resume again when the VCR s power is turned off as long as the tape has not been ejected from the VCR Does COMMERCIAL ADVANCE work in all recording speeds Yes COMMERCIAL ADVANCE works in SP and SLP Will COMM
30. ble system when attached RF OUT Jack Passes signal to TV using the cable supplied 60 APPENDIX REFERENCE TROUBLESHOOTING TIPS No power e Check to make sure it is plugged into an operating outlet e Check to make sure your connections are correct VCR does not respond to remote e Check to make sure there are no objects between the VCR and remote e The batteries may need changing e Make sure the Remote VCR1 VCR2 setting is set to VCR1 so the remote that came packed with your VCR can operate it Poor or no picture for normal TV viewing e Check to make sure the VCR indicator is off e Check to make sure the TV is switched to an active channel e Check to make sure the antenna connections are secure and correct Snowy or no picture during playback e Press TVeVCR to turn VCR indicator on e Check TV channel selected 3 or 4 to make sure it matches the channel selected with 3 CH 4 switch on back of VCR e Check to make sure the TV s fine tuning is correct for the channel you have selected e Check video cable connections between VCR and TV monitor e Check to make sure the TV monitor is set to Video Input see page 68 for more information e Try another tape e Some snow streaks are normal during search stop action frame advance and slow motion playback Streaks in picture during normal playback e Press one of the TRACKING buttons to move streaks up or down for the best picture e Check to m
31. d through menus go to the next section to set up individual menus of your VCR SETTING UP THE VCR ADDITIONAL SET UP FEATURES 1 Below is a list of set up features that you need to set up before using your VCR for the first time FIRST THINGS FIRST e Select a Language Set Up for a Cable Box 2 SETTING UP THE VCR e Set Up aVCR Channel List Auto Channel Search 3 VCR BASICS e Auto Clock Set Feature e Set Time and Date Manually e Set UpVCR Plus Channels A RECORDING e Set the Remote VCRI VCR2 Feature e Set the Auto Play Feature Set the EnergySaver Feature 5 PROGRAM THE REMOTE Set Front Panel Brightness Feature Set the Preferred Tape Speed Feature 6 OTHER FEATURES 7 CONNECTIONS Q REFERENCE N SETTING UP THE VCR USING THE MENU TO SET UP FEATURES You can set up your VCR s features by using the remote control s buttons to enter your choices from on screen instructions Each menu item is explained in this section You can set up features individually by using the menu system Each feature that appears in the initial set up is explained in this section as well as a few others you may want to set up before you begin using your VCR LANGUAGE SELECTION 1 On your remote control press the MENU button to display the VCR MAIN MENU VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 7 to select the LANGUAGE menu LANGUAGE
32. day in October The VCR clock automatically changes from 2 a m to 1 a m back one hour Therefore it can affect your recording length SETTING UP THE VCR VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 3 to display the TIME menu TIME Set Time and Date Auto Clock Set ON Set Time Zone Set Daylight Savings XDS Time Data was not found 0 Exit 3 Press 1 to display the SET TIME AND DATE menu SET TIME AND DATE Time Chh mm Date Press MENU to cancel 4 Enter the data using the number buttons Press 0 before single digit numbers and follow the on screen directions SET TIME AND DATE Time 12 34 PM Date 11 18 99 Thursday Press CLEAR to correct Press MENU to set Time Date Display Pressing INFO on the remote displays the time and date on the screen 15 16 SETTING UP THE VCR VCR Plust SYSTEM CHANNELS Using the VCR Plus system can make programming timer recordings for cable or off air antenna easier but you have to put in a little time right now to set up a channel list A worksheet and abbreviated codes for typical cable services in the United States and Canada are provided 1 Press MENU to display the VCR MAIN MENU VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 4 to display the CHANNELS menu CHANNELS Auto Channel Search
33. e clock or a timer recording F ADV Lets you view one frame with each press of the button when tape is in pause FORWARD Fast forwards the tape when the VCR is stopped Searches forward through a tape during playback Starts slow motion during play pause and increases slow motion speed GO BACK Switches between two channels Select one channel and then select another using the number buttons Press GO BACK to switch between the two channels In menu mode press to go back to a previous menu INFO Shows the status displays on the TV screen INPUT Selects between the VCR s line input or tuner Line input refers to the signal coming from the component connected to the AUDIO VIDEO IN jacks on the back L1 or front L2 of the VCR MENU Brings up VCR MAIN MENU on the TV screen 22 VCR BASICS Numbers 0 through 9 Select a channel up to 99 by pressing two numbers Select a cable channel over 99 by pressing and holding 1 until 1 appears on the screen Then press the other two numbers PAUSE Pauses playback or recording Press PAUSE again to return to playback or recording PLAY Plays a tape RECORD Starts VCR recording Also used for Express recording REVERSE Rewinds the tape when the VCR is stopped Searches backward through a tape during playback Starts slow motion during play pause and decreases slow motion speed SEARCH Displays INDEX and GO TO Search menus on TV screen when VCR is stopped Advances the tape
34. een saved Channel 104 Cable Remember to insert a Start Time 08 00 PM recordable tape and End Time 09 30 PM turn the VCR off before Start Date 11 18 99 Thu the program start time Tape Speed SLP Remember to leave your Press CLEAR to erase cable box on and tuned Press MENU for next prog to the desired channel TIMER RECORDING WITH VCR Plus INTERACTIVE PROGRAM GUIDE SYSTEM You can use the VCR Plus system code numbers to simplify timer programming if you have cable TV and don t receive all channels through a cable box or if you receive your TV signal off air Setting Up the Channel List If you did not set up the VCR Plus programming system channel VCR MAIN MENU i x 1 VCR PL list you can do it now Sette Bo ebalnee 3 Ti 1 Display the CHANNELS menu from the VCR MAIN MENU acehennene 2 Display the VCR Plus Channel List menu CHANNELS Auto Channel Search Add Remove Channels Signal Type CABLE VCR Plus Channel List 3 Goto section four Setting Up Your VCR if you need more information on setting up your VCR Plus programming system channel list FWN VCR Channel My Channel 46 Using the VCR PLUS Programming System 23 1 Press MENU to bring up the VCR MAIN MENU Use CH to select Press 0 9 to change VCR MAIN MENU Press MENU to save VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 1 to display the VCR Plus system menu VCR PLUS Enter
35. elect the TV s video input with the remote control s INPUT button to see the signal If you have trouble understanding the Video Input Channel look to page 68 for a more detailed explanation STEP 6 TURN ON THE VCR Press POWER on the VCR s front panel or the VCR button on the remote control to turn on the VCR The first time you turn the VCR on a menu screen appears This is the start of an initial set up which helps you set different options for your VCR STEP 7 INITIAL SETUP The first on screen menu during the initial set up asks which language you prefer to use for your VCR Use the remote control s number buttons to select options Select a language Seleccione un idioma Choisissez une Langue 1 English 2 Espanol 3 Francais 1 Press 1 for English 2 for Espa ol Spanish or 3 for Fran ais French The remaining menus throughout the set up will appear in the chosen language Just follow the step by step procedures until setup is complete If the menu does not appear e Make sure the TV is tuned to the same channel as the 3 CH 4 switch or the TV s Video Input Channel see page 68 for more information e Make sure the VCR indicator is on in the VCR display if you connected your VCR using the ANT IN and RF OUT jacks e Check your connections If you chose to set up your VCR options individually then go to the next section VCR Viewing Channel OUT IN ANT IN o ore qa A iunio RF OUT R
36. eps 6 9 to copy or edit additional segments Caution The unauthorized recording of satellite broadcasts television programs or other copyrighted materials may infringe the rights of others Two VCR Connection CABLE BOX IN f cn OR ae PLAYBACK VCR RECORDING VCR PROGRAM THE REMOTE CONTROL YOUR TELEVISION FIRST THINGS FIRST mk w Vi The remote can be programmed to control a television It is programmed to control an RCA GE or PROSCAN TV Other manufacturer s brands need to be programmed D SETTING UP THE VCR 3 VCR BASICS RECORDING 5 PROGRAM THE REMOTE 6 OTHER FEATURES 7 CONNECTIONS Q REFERENCE PROGRAM THE REMOTE ABOUT PROGRAMMING THE REMOTE The remote can be programmed to control other brands of remote controllable TVs It is already programmed to operate most RCA GE and PROSCAN televisions PROGRAMMING THE REMOTE TO CONTROL ATV If the TV does not turn on when you press the TV button the remote needs to be programmed Follow these steps to program the remote to control your particular TV 1 Turn on the TV 2 Find your TV brand and code number s on the code list on the next page 3 Press and hold the TV button on the remote 4 Enter the code from the code list 5 Release TV and then press CHAN up or down If the TV responds to the remote commands the remote is programmed 6 If the TV does not r
37. espond repeat these steps using the next code listed for your TV s brand OPERATING THE TV After you set up the remote see which buttons operate your TV 1 Point the remote at the TV and press the TV button If the TV does not turn on press the TV button and then press the ONeOFF button 2 You may want to experiment to see which buttons operate your TV Try pressing buttons such as VOL and MUTE See TV Function Buttons in the VCR Basics Section for details This remote may not operate all models of the brands that are shown Note the difference between the TV and VCR on screen displays to see which one the remote is operating 36 PROGRAM THE REMOTE TV Codes Citizen Philco Colortyme Philips Concerto Pioneer Curtis Mathes Portland Daewoo PROSCAN Daytron Proton Electrohome Quasar Radio Shack Hitachi Infinity J C Penney 00 01 06 09 12 Magnavox Marantz 37 OTHER FEATURES FEATURES TO ENHANCE VCR OPERATION FIRST THINGS FIRST Commercial gt gt Advance Movie gt gt Advance D SETTING UP THE VCR Picture Search Options Tracking 3 vcr Basics e Pro Tect Plus Locking Time Counter On Screen Displays A RECORDING e Audio Reception e Audio Playback 5 PROGRAM THE REMOTE 6 OTHER FEATURES 7 CONNECTIONS Q REFERENCE lt lt lt lt lt lt lt lt w OTHER FEATURES COMMERCIAL gt gt ADVANCE COMMERCIAL gt
38. ess SEARCH to exit INDEX SEARCH 4 Press FWD to search forward or REV to search in reverse The Sede chtnan ker VCR will locate your index mark and begin playback If you unde x number lees did not enter a specific index number the VCR will locate the next index mark and begin playback 5 Press STOP to end index searching Press STOP to cancel Some index marks may be missed by the VCR INDEX SEARCH e A mark too close to your location on the tape eS eee fon P index marks e The mark at the beginning of a recorded segment of five minutes or less e The first index mark on the tape when you start at the beginning of the tape Press STOP to cancel OTHER FEATURES GO TO SEARCH The Go To Search feature enables the VCR to quickly locate a GO TO SEARCH counter reading anywhere on the tape When the VCR locates Current tape counter is 2 17 25 the counter reading it will begin playback Press REV or FWD 1 Press STOP to go to 00 Press SEARCH to exit 2 Press SEARCH on the remote until the GO TO SEARCH menu appears on the screen GO TO SEARCH 3 Press number buttons to enter the hour and or minute of Current tape counter is the counter reading you want the VCR to go to Press 2247225 CLEAR on the remote to correct an entry Press REV or FWD 4 Press FORWARD to search ahead or REVERSE to search re gee behind Press SEARCH to exit 5 Press STOP to end Go To searching
39. ette and reinsert VCR forwards through commercials or momentarily displays a blue screen during playback e Commercial Advance Playback feature is set to AUTO Set it to MANUAL APPENDIX REFERENCE COMMERCIAL gt gt ADVANCE feature does not mark commercials when The Marking feature is set to OFF in the COMMERCIAL ADVANCE menu Set it to ON A recording is less than 15 minutes or the commercial is longer than one minute A single isolated commercial can not be marked Recording started in the middle of a commercial segment A commercial group within the first or last two minutes of a recording Accuracy and effectiveness can vary depending upon program content and the characteristics of the commercials A commercial is between 30 and 45 seconds and 45 and 60 seconds Effectiveness may vary when local television stations insert their own commercials Commercials recorded even though COMMERCIAL gt ADVANCE feature was set to ON COMMERCIAL gt gt ADVANCE is designed to record the commercials mark them and then skip over the marked commercials during playback 65 APPENDIX REFERENCE 66 QUESTIONS AND ANSWERS ABOUT gt gt COMMERCIAL ADVANCE Will commercials be scanned through only on playback of recordings Yes The VCR does not rewind and mark commercial segments until after recording is finished How fast does the COMMERCIAL gt gt ADVANCE VCR scan through the commercial breaks In SLP t
40. ge 69 23 VCR BASICS 24 Numbers 0 through 9 Select a channel up to 99 by pressing two numbers Select a cable channel over 99 by pressing and holding 1 until 1 appears on the screen Then press the other two numbers ONeOFF Turns a compatible TV off and on VOL Up and Down Raises and lowers sound of TV PLAYING A TAPE 1 Tune the TV to your VCR viewing channel 3 4 or TV s video input see page 68 for more about the video input channel Press the VCR button on the remote control to switch to VCR viewing mode The front panel display will indicate VCR 2 Insert a tape in the VCR If the Auto Play feature is set to ON the tape automatically begins playback if the safety tab on the cassette is removed e Press FWD or REV to position the tape e Press PLAY PAUSE if necessary on the VCR PLAY on remote to begin tape play e Press PLAY PAUSE PAUSE on remote for stop action e Press TRACKING up or down to remove any streaks from the picture if necessary e Press STOPeEJECT on VCR STOP on remote to stop playback AUTOMATIC REWIND The VCR automatically rewinds the tape if it reaches the end of the tape during playback While rewinding you can press POWER on the VCR ONe OFF on remote and the VCR will turn off after rewinding Pause If you pause the VCR automatically switches from pause to stop after a few minutes to reduce tape wear Automatic Tracking
41. gt ADVANCE is patented technology that detects and marks most commercials on your tape for any recording that is more than 15 minutes long After recording the VCR rewinds the tape to the beginning of the recording and determines where the commercials are located It then marks the beginning and end of the detected commercial segments and when finished returns the tape to the end of the recording It does not erase commercials from the tape During playback the VCR automatically skips the detected commercial segments or you can chose to manually skip them This feature reduces three minutes of commercials to approximately 8 12 seconds of fast forwarding in the SLP speed You can select a background display of blue or see the video as the commercials are skipped Because television signals do not indicate where commercials are located this feature finds and marks them through a set of formulas based on how television is broadcast today Since television stations broadcast differently and insert their own commercials you may experience some variations in this feature s effectiveness Station promotions identifications and announcements are not considered commercials but might be skipped For more information see Questions and Answers About COMMERCIAL gt gt ADVANCE in the Reference section All of the COMMERCIAL gt gt ADVANCE features are accessed through the Commercial Advance menu 1 Press MENU to display the VCR MAIN
42. hen turn the VCR off If the time does not set within 10 minutes set the time and date manually through the menus Preferences Audio Language Exit 2 Press 3 to display the TIME menu Check your local cable system or TV stations for availability of channels with XDS 13 14 SETTING UP THE VCR TIME Set Time and Date Auto Clock Set ON Set Time Zone Set Daylight Savings XDS Time Data was found on channel 20 0 Exit 3 Press 4 to display the SET DAYLIGHT SAVINGS menu SET DAYLIGHT SAVINGS Does your area observe Daylight Savings Time from April to October DST is observed 3 gt Automatic Press MENU to continue 4 Select one of the options and then press MENU to continue e DST stands for Daylight Saving Time e If you chose Automatic the VCR sets the clock using the DST information broadcast in the signal channel Setting the Time and Date Manually If the Auto Clock Set was unsuccessful set the clock through the TIME menu The Auto Clock Set feature is set to OFF automatically when you set the clock this way 1 Press MENU to display the VCR MAIN MENU Spring forward Fall backward In the Spring daylight saving time begins on the first Sunday in April Because the clock automatically changes from 2 a m to 3 a m forward one hour including the extra hour for timer recording within this time frame is necessary In the Fall Daylight Saving time ends on the last Sun
43. ideo ALL channels enter two numbers for output channel of your cable box or press INPUT if you connect your cable box with AUDIO VIDEO jacks Only SOME channels if you only use the cable box to tune premium channels Enter 01 13 or INPUT Press MENU to cancel Cancel setup select to cancel SETTING UP THE VCR CABLE BOX SETUP On what channel does the VCR receive signals from the cable box Cusually 3 4 or video 04 Press CLEAR to correct Press MENU to continue 5 Once you complete the setup the VCR confirms that the VCR will now receive all signals on the designated channel For example CABLE BOX SETUP The VCR will now receive all signals from the cable box on channel 04 Press MENU to continue VCR CHANNELS LIST If you use a cable box for all channels this step is not necessary Your VCR may come with a channel list preset at the factory but you may want to add or delete some channels depending on whether they are active To Auto Channel Search 1 Press MENU to display the VCR MAIN MENU VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 4 to display the CHANNELS menu pa Auto Channel Search CHANNELS Use the Auto Channel Search feature to place all available channels in memory Auto Channel Search Add Remove Channels Signal Type CABLE VCR Plus Channel List Cable Box Setup If you ever change cable or antenna
44. l erase 3 Start audio source playing and press RECORD to begin anything that was previously recording recorded on the tape 4 Press STOP when you are finished Playing Back Audio Only To get stereo sound connect the AUDIO OUT jacks of the VCR to the appropriate input on your amplifier or receiver Do not use BACK OF VCR the phono input Refer to your amplifier or receiver user s guide Audio Connection USING TWO VCRS FOR COPYING AND EDITING TAPES Use one VCR as the playback VCR and the other as the recording VCR 1 Connect the VCRs using the diagram at the right PHONO TUNER 2 Turn on both VCRs and TV BACK OF AMPLIFIER RECEIVER Continued on Next Page 33 34 RECORDING 3 Tune the TV to the VCR viewing channel either 3 4 or TV s video input See page 68 for more information 4 Ifyou are using coaxial cables for the connection tune recording VCR to channel 3 or 4 the one selected on the playback VCR If you are using audio video cables select the line input on the recording VCR 5 Insert the tape you want to copy into playback VCR Insert a blank tape with its safety tab in place into recording VCR 6 Using visual search locate the segment you want to copy on the playback VCR Pause the tape at this location 7 Press RECORD on the recording VCR then PAUSE 8 Press PAUSE on both VCRs to begin copying 9 Press PAUSE on both VCRs to stop copying 10 Repeat st
45. lay the CHANNELS menu 3 Press 2 to display the ADD REMOVE CHANNELS screen Use the CHAN up or down keys on the remote or number buttons to go to the channels you want to remove or add ADD REMOVE CHANNELS ADD REMOVE CHANNELS Channel 115 Channel 115 is presently ADDED is presently REMOVED Press CLEAR to remove Press INFO to add Press MENU to exit Press MENU to exit 4 When at the channel it will be added if not already on the list or deleted if it was If the channel was added you can press CLEAR to remove it If the channel was deleted you can press INFO to add TIME AND DATE The VCR gives you two ways to set the time and date the Auto Clock Feature or manually The Auto Clock Feature enables the VCR to update the clock each time the VCR is turned off The Auto Clock is advantageous because it updates the time for you automatically Before you set the time and date set the Auto DST Daylight Saving Time feature to ON or OFF for your area Auto Clock Set Feature The Auto Clock Set feature is set to ON at the factory In the ON setting the VCR looks for a channel carrying XDS Extended Data Services information XDS updates the clock using the Coordinated Universal Time To use this automatic feature certain steps are required such as Auto Channel Search setting the time zone and setting the Daylight Saving feature before Selecting Channels the Auto Clock feature works The Channel up and down buttons access
46. n works well for tapes recorded at the SP or SLP speed 1 During playback press PAUSE and then FWD or REV to begin slow motion playback 2 Press FWD to increase or REV to decrease the speed of the search 3 Use TRACKING up or down to remove any streaks from the picture 4 Press PLAY to return to normal playback The VCR switches automatically from slow motion playback to stop after a few minutes 45 46 OTHER FEATURES FRAME ADVANCE Frame advance lets you view recorded action one frame after another during playback Frame advance works well for tapes recorded at the SP or SLP speed e Pressing PAUSE freezes the action e Pressing FADV repeatedly views single frames of the action e Pressing PAUSE or PLAY returns normal playback INDEX SEARCH The VCR has a VHS Index Search System that automatically records an index mark on the tape every time you start a recording During playback you can locate the program you want to play by the number of index marks or by scanning The VCR will search forward or reverse from the location you are on the tape To Search 1 Press STOP INDEX SEARCH 2 Press SEARCH on the remote to display the INDEX SEARCH De bee ae ce nei on screen display OR enter a specific 3 If you want to search through a certain number of index al SE marks press two number buttons to enter the number of marks you want to search Press CLEAR on the remote to correct an entry Pr
47. nnsaanses 9 VCR Channels List siicc ndencsccneeciencieaeds 10 Auto Channel Search ssssssessseessesseeeenn 10 Change the Signal Type ceeeeeeeeee 12 Adding or Removing Channels 5 12 Time and Date sasicissscicsnnncemiiaseconak 12 Auto Clock Set Feature eeceeteeeeeeees 13 Set the Time Zone ccceecceeesseeeeeeteees 13 Set Daylight Saving Time eeeeeee 14 Setting the Time and Date Manually 15 VCR Plus System Channels ccccccccceeee 16 Additional Set up Features ccceccceeeeee 18 Remote VCR1 VCR2 Option sesse 18 Auto Play iein ae e enaa 19 ENIGPOY SAVER ia a ai 19 Front Panel Brightness VCR Display 20 Preferred Tape Speed cc cccessceeeeteeeeeeees 20 WCR BaSiCS iia aaa n eaaa aaa eaka a a ns 21 Remote BUTTONS asiaa airas 22 Component Buttons eseese 22 VCR Function Buttons seee 22 TV Function Buttons seese 23 Playing a Tape snssssssesesssseeessernsserrnnrennresserrnsrrre n 24 Automatic Rewind sssssesssssenssenersseeressrrrrnerrrne 24 Tape Eject naiue e aaae 25 RECOMGING eases cat arannana anaie anae an aeara aoaaa tinaaa 25 Recording onen aaa ri iie aia 27 Recording Features ccccccsccceeeeseceeeeesseeeeeeeees 28 Express Recording XPR cccsssseeeesssseeeeees 28 Timer Recording cscs cscdensratednsssceacestandsiaaasssace 29 Timer Recording with VCR Plus Interactive Program Guide System 30 Se
48. ntrol VCR2 Auto Play ON EnergySaver 2 00 Front Panel AUTO Tape Speed SLP Commercial Advance 0 Exit The PREFERENCES menu allows access to many VCR options including remote control Auto Play and EnergySaver features 19 SETTING UP THE VCR e AUTO brightens the display when the VCR is on and dims the display when the VCR is off e BRIGHT keeps the display bright when the VCR is on or off e DIM keeps the display at a low brightness level at all times PREFERRED TAPE SPEED You can set the preferred tape speed between Standard Play SP and Super Long Play SLP In the PREFERENCES menu press 5 to switch between the options e SP sets the preferred recording speed to SP e SLP sets the preferred recording speed to SLP Tape Speeds SP Standard Play Gives the best quality recording but fewer programs can be recorded on the tape Special effects such as pause slow motion picture search and frame advance work well when you play back tapes recorded in this speed SLP Super Long Play Gives approximately three times the recording time of tapes recorded in SP Special effects such as pause slow motion picture search and frame advance work well when you play back tapes recorded in this speed Approximate Recording Times Cassette SP SLP T 120 2 Hr 6 Hr T 160 2 Hr 40 Min 8 Hr 20 VCR BASICS LEARN THE BASICS TO GET FIRST THINGS FIRST YOU STARTED These VCR basics should be enough for y
49. o make sure the VCR was turned off at the time recording was to start Check to make sure there was a tape in the VCR and the cassette s safety tab was intact VCR ejects cassette when the end of the tape is reached during a timer recording Check to make sure VCR Plus setup was completed correctly APPENDIX REFERENCE Will not record e Check to make sure the safety tab is intact e Check to make sure the VCR is not in the line mode Press INPUT on the remote Clock shows incorrect time or date e Power interruption e Check to make sure the clock is set accurately check AM PM and date e Check Daylight Saving setting The clock may have adjusted for daylight saving time Time did not adjust for Daylight Saving time e Check to make sure daylight saving feature is set correctly VCR makes noise when stopped e VCR is removing tape from heads This is normal The head cylinder inside the VCR will continue to rotate for a few minutes after you put the VCR in the stop mode Will not Auto Channel Search active channels correctly e Check to make sure the antenna connections are secure and correct e Check to make sure the Signal Type CABLE ANTENNA feature is set correctly e If Detect Automatically was selected for the Signal Type in the AUTO CHANNEL SEARCH menu try using either CABLE TV or ANTENNA instead e May not be necessary if using a cable box for all channels Contact your local cable company for more
50. ormation needed in the first three sections To help you along there s even an initial set up feature the first time you turn on your VCR which walks you through several set up steps at once FIRST THINGS FIRST D SETTING UP THE VCR GETTING STARTED Before this first step though learning about the time and date your remote control s features working with channels and basic video tape operations are essential to get all you can out of the VCR Once you are comfortable with these features feel free to refer to other sections because they cover the more detailed information 3 VCR BASICS RECORDING mk lt lt lt lt WHAT REMAINS The final sections of this manual contain playback and recording information a detailed connections section and a reference section including y troubleshooting tips warranty information and an index 6 OTHER FEATURES 5 PROGRAM THE REMOTE 7 CONNECTIONS Q REFERENCE m Benne READ ME These note boxes give you tips for your new video cassette recorder FIRST THINGS FIRST STEP 1 WHAT S IN THE BOX The following items come packed in the box e VCR e Remote control e RF coaxial cable STEP 2 INSTALL BATTERIES IN THE REMOTE CONTROL Follow these steps whenever you need to install or change the batteries in your VCR remote 1 Remove the cover of the battery compartment 2 Place the batteries into
51. oth or the dusting attachment of your vacuum cleaner to dust your VCR Remove dust from the ventilation holes Plastic surfaces are easily scratched and can be marred by alcohol and various solvents Avoid excessive use of oil based furniture polishes since the materials used in the cabinet will accumulate more dust A nonabrasive antistatic cleaner polisher is recommended Product Registration Please fill out the product registration card and return it immediately Returning the card allows us to contact you if needed Keep your sales receipt to obtain warranty parts and service and for proof of purchase Attach it here and record the serial and model numbers in case you need them The numbers are located on the back of the product Model No VR646HF Serial No Purchase Date Dealer Address Phone VCR Plus system and PlusCode are registered trademarks of Gemstar Development Corporation The VCR Plus System is manufactured under the license from Gemstar Development Corporation COMMERCIAL ADVANCE and MOVIE ADVANCE are registered trademarks of SRT Inc a Jerry Iggulden invention licensed in association with Arthur D Little Enterprises TABLE OF CONTENTS First Things First osc ociicecnat eenean eessen rerne 3 Setting Up the VCR naiseta aii 7 Using The Menu To Set Up Features e 8 Language Selection ccceeesseeeeeeeeeeeeeeeees 8 Cable Box Setup ixcchiacnivaOs0ss onacnenctieanaeacie
52. ou to begin enjoying your VCR Learning the remote control functions playing a recorded tape and recording a program should do just that D SETTING UP THE VCR This section shows you the basics of using your VCR It discusses things like using the remote control playing a tape and recording programs 3 vcr Basics RECORDING 5 PROGRAM THE REMOTE 6 OTHER FEATURES 7 CONNECTIONS lt lt lt lt lt lt lt Q REFERENCE VCR Basics tells you what you need to know in order to watch a movie or tape your favorite show 21 VCR BASICS REMOTE BUTTONS The remote control is capable of controlling your VCR and many brands of televisions If you have an RCA GE or PROSCAN TV you may be able to control it without having to program the remote COMPONENT BUTTONS ONeOFF Turns off VCR when remote is set to control the VCR Also turns some compatible components on and off TV Turns on a compatible RCA GE or PROSCAN TV and sets the remote to control the TV Also used with the ONeOFF button to turn on a different brand of TV if programmed and sets the remote to control the TV VCR Turns on a compatible RCA GE or PROSCAN VCR and sets the remote to control the VCR VCR FUNCTION BUTTONS CHAN Up or Down Selects next higher or lower channel in the VCR s channel memory CLEAR Resets time counter to 0 00 00 Allows you to change Y TRACKIN A FADV entries when setting th
53. page 68 for more information 53 54 CONNECTIONS TV WITH RF JACK ONLY This connection assumes e You are connecting antenna cable or cable box system e Your television has only an RF input jack This connection provides e Mono sound playback from VCR e Record one channel while watching another except when using a cable box for all channels To use this connection you must have e 1 coaxial cable for cable or antenna connection 2 for cable box To connect 1 Connect cables as shown 2 Return to First Things First then follow the steps Using This Connection Tune your TV to channel 3 or 4 whichever one you selected with the 3 CH 4 switch on the back of the VCR To play a tape 1 Insert a tape 2 If necessary press PLAY To record one program and watch another 1 Begin recording a program using one of the recording features 2 Press the TVeVCR button and select a different channel on the TV CABLE CABLE BOX OR ae CABLE ANTENNA CONNECTIONS TV WITH AUDIO VIDEO JACKS This connection assumes e You are connecting an antenna cable or cable box system e Your television has audio video jacks This connection provides e Hi Fi stereo sound playback from VCR e Record one channel while watching another except when using a cable box for all channels To use this connection you must have e 1 coaxial cable for cable antenna connection 2
54. prerecorded movies rented or purchased This feature works two ways 1 you can go to the beginning of the movie or 2 you can skip from one preview to the next MOVIE gt ADVANCE works only on cassettes recorded in the SP speed with the safety tab removed 1 To select MOVIE gt gt ADVANCE insert a tape with the safety tab removed and press SEARCH The following menu appears MOVIE ADVANCE What type of tape is this 1 Purchased Rented Movie 2 Home Recording 3 Other Press CLEAR to cancel 2 Press 1 if the tape is a purchased or rented movie press 2 if it s a recording made at home or press 3 if it s something else you don t know or you do not want to select MOVIE gt ADVANCE Pressing 2 or 3 gives the same response and takes you to a different search feature If you accidentally make a wrong selection press STOPeEJECT on the VCR STOP on remote and reinsert the tape Press SEARCH If you press 1 the MOVIE ADVANCE menu appears MOVIE ADVANCE Would you Like to go to the start of the movie or to the next preview 1 Go to movie 2 Go to preview Press CLEAR to cancel 3 Press 1 to advance directly to the beginning of the movie or press 2 to view the first next preview MOVIE gt gt ADVANCE works only on cassettes recorded in the SP speed with the safety tab removed MOVIE ADVANCE is a registered trademark of Aurthur D Little Enterprises Inc 43 OTHER FEATURES
55. r Specifications are subject to change 67 APPENDIX REFERENCE HOW TO FIND YOUR TV S VIDEO INPUT CHANNEL Hy Button You need to tune your TV to the Video Input Channel if you are using the VCR s AUDIO VIDEO OUT jacks to connect to the TV s AUDIO VIDEO INPUT jacks You must select this channel before you can see the VCR s menus the cable or antenna reception and the content that s on a tape The Video Channel on TVs varies for different brands and different models Below are some steps to try e If your TV brand is RCA GE or PROSCAN press the TV button on the remote control that came with the VCR Then press the INPUT button on the remote e If you have another brand of TV consult the section Programming The Remote to see if the VCR s remote control can be set to control your TV If so follow the step above If those options do not work try the following ideas You might access the Video Input Channel by e pressing a button on the remote see table below INPUT Button e selecting the channel from the TV s menu system see table below V TRACKIN a e tuning directly to the channel by selecting a specific channel number see table below e going through all the channels in the channel list by pressing the channel up or down buttons on the TV Some common scenarios are listed in the Video Input Channel Variations table that follows Video Input Channel Variations Button Switch B
56. rame advance 40 go to 41 index 42 slow motion 39 SEARCH button 22 Second Audio Program SAP recording 31 Set up cable box 9 language 8 using menus 8 Signal type changing 12 Skipping commercials 33 SLOW button 23 Slow motion search 39 Specifications 61 Speed SLP 20 SP 20 SPEED button 23 31 Speeds recording 20 STOP button 23 31 STOPeEJECT button 52 72 T Tape eject 24 Tape speeds 20 Time Counter 42 Timer recording 26 stopping 30 with VCR Plus 26 Tips troubleshooting 55 TRACK buttons 23 Tracking 41 Troubleshooting tips 55 TVeVCR button 23 31 vV VCR channel list 9 VCR cleaning 61 VCR indicator 31 VCR MAIN MENU 9 VCR Plus channel list 16 channel list Canada 17 channel list USA 16 recording 29 worksheet for channels 17 VCR viewing channel 5 INDEX Ww Warranty 63 Xx XPR express recording 26 73 If your VCR needs service please contact your dealer or the nearest Servicenter from the yellow pages Please do not send any products to the Indianapolis address listed in this manual or on the carton This will only add delays in service for your product 1 THOMSON CONSUMER ELECTRONICS 10330 North Meridian Street Indianapolis IN 46290 1999 Thomson Consumer Electronics Inc Trademark s Registered Marca s Registrada s Printed in Mexico TOCOM 1540772B mca Ls As an Enercy Star Partner Thomson Consumer Electronics has determined that this product or produc
57. rding automatically starts and stops a recording at a predetermined time e Timer Recording with VCR Plus Systemprogramming the VCR by just entering a PlusCode programming number found in TV guides EXPRESS RECORDING XPR Use express recording when you want to quickly record the remaining portion of the program you are watching 1 Set the tape speed to SP or SLP by pressing TAPE SPEED on the VCR SPEED on the remote 2 Press the RECORD buttonto begin recording 3 Repeatedly press the RECORD button to set up the recording time duration REC CH 36 Record Length 0 00 REC CH 36 Record Length 1 30 Press REC to set length Press REC to set length Each time you press the RECORD button you increase the recording time up to 4 hours The VCR continues to record for the amount of time you indicate and then automatically turns off To stop an express recording press and hold STOP for three seconds 28 Express Recording Express recording is a great way to tape the last quarter of the game or the last part of a movie when you have to leave RECORDING TIMER RECORDING You can set up as many as eight timer recording programs 1 Press MENU to display the VCR MAIN MENU VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 2 to display the TIMER RECORDINGS menu TIMER RECORDINGS Create a New Program Review Existing Progs Use VCR Plus
58. se slow motion picture search and frame advance work well when you play back tapes recorded in this speed SLP Super Long Play Gives three times the recording time of tapes recorded in SP Special effects such as pause slow motion picture search and frame advance work well when you play back tapes recorded in this speed Recording Time Cassette SP SLP T 120 2Hr 6Hr T 160 2Hr 8Hr 40 min 25 RECORDING SEVERAL RECORDING OPTIONS Now that you ve gone through the basic steps necessary to operate your VCR it s time to explain the different advanced recording features available to suit your needs Recording Features on your VCR include Recording explained in the VCR Basics section Express Recording XPR Timer Recording Timer Recording with VCR Plus Interactive Program Guide System Broadcast Stereo or Second Audio Program SAP Audio Only Recording Copying and Editing Tapes FIRST THINGS FIRST D SETTING UP THE VCR 3 ver Basics RECORDING 5 PROGRAM THE REMOTE 6 OTHER FEATURES 7 CONNECTIONS Q REFERENCE lt lt lt lt lt lt lt lt Ww N RECORDING RECORDING FEATURES There are four ways to record programs e Recording pressing one button to start recording a program see VCR Basics section e Express Recording starts recording a program already being watched and automatically stopping recording after a designated period of time e Timer Reco
59. ssesesseseeeseeessserrrreree 49 REGCODUION noceant neee aat aeei 50 Tape Playback csc ipicticsauicrerianadrarantarwecnmtenes 50 Connections a se eee 51 Things to Know Before Connecting 2 00 51 Connecting Your VCR sssssessersssssrerrrirrsssseeee 52 Jacks and Cables icciscccsiee cadaeicinisenmaaiacens 52 RF Jacks and Coaxial Cables 0008 52 Audio Video A V Jacks and Cables 52 Choosing a VCR Connection ccccceeeeeeeeeees 53 Advantages of A V Cable Connections 53 TV with RF jack Only 00 eeceeeeeteeee eee eeeeee 54 TV with A VV jacks sexs desieraetaavarcardancucs oaddustrnaune 55 TV with A V Jacks and Cable Box to Unscramble Pay Channels Only 56 Reference ccccccceccsccccesseeeeeeesseeeeessseeeeesessaeeeeess 57 Front Pane heanin ad Recent 58 Display Panek nerrerianisenie a e 59 Back Panel nannan oi A T 60 Troubleshooting TIP sssssssessseeessrnssesrnnesreenesene 61 Questions and Answers About Commercial Advance cccccccccesssssteeeeeeeeeeeeees 66 Sp cifications edanaren iaa de aae ave aeaaeai aana nean 67 Cleaning the VCRi sic saicaiecandtitineaalaidteee 67 How to Find Your TV s Video Input Channel 68 Limited Warranty vise i cdi ated lian 69 DINO Ka isis veri acca ints T E TA 70 FIRST THINGS FIRST WELCOME TO YOUR NEW VCR To help you get started using your VCR with as little reading as possible we ve put all the basic inf
60. st 30 45 and 60 second commercials A commercial group starting with the first two minutes or last two minutes of a recording will not automatically be skipped A commercial will not be skipped if a recording starts in the middle of a commercial segment one isolated commercial is shown without others or a commercial is longer than one minute Press FWD on the VCR FORWARD on remote to scan through the commercial Part of a recorded program may be skipped if the program segment is between commercials and less than one minute or there are frequent dark and quiet scenes If part of the program is skipped rewind the tape to the beginning of the skipped program segment and press PLAY e Select MANUAL and the VCR won t advance through the blocks of marked commercials until you press SEARCH If you press SEARCH during playback of material other than commercials the VCR advances to the end of the next marked commercial block and resumes playback The VCR resumes playback when it reaches the end of the marked commercials COMMERCIAL gt ADVANCE Display Press 3 to switch between Display BLUE or VIDEO e Select BLUE to display a blue background when the VCR advances through the block of marked commercials e Select VIDEO to display the recorded video when the VCR advances through the block of marked commercials 42 OTHER FEATURES MOVIE gt gt ADVANCE MOVIE gt gt ADVANCE helps you locate certain parts of
61. t model meets the Enercy Star guidelines for energy efficiency
62. the VCR button on the remote for approximately six seconds TIME COUNTER The time counter shows the actual time it takes to record a program or play back a segment of a recorded tape It helps locate the beginning or end of programs you taped The time 0 30 00 counter resets to 0 00 00 whenever the tape is ejected from HOURS _ MINUTES the VCR SECONDS For example if you record a 30 minute program at the beginning of the tape and you want to go to the end of that program to begin another recording you would 1 Press INFO twice to display the time counter Timer Counter on screen display shows hours minutes and seconds 2 Press CLEAR to reset the time counter to 0 00 00 of a segment of tape 3 Press FWD to forward the tape until the time counter reads 0 30 00 4 Press STOP This is the approximate end of the program You may want to press PLAY to verify Now you can begin recording at this spot 5 Press INFO to remove the time counter from the screen and return to the normal display mode 48 OTHER FEATURES ON SCREEN DISPLAYS 1 Stop Ch 05 __ 9 30 00 HOURS J The INFO button shows the status of the VCR STOP PLAY MINUTES SECONI RECORD etc channel number time counter date time and tape speed on the TV screen The date and time must be set before they can be displayed 11 18 99 Thu 01 30PM SLP 1 Press INFO to see the on screen displays Orscreen display aries ut 2 Press INFO again to ha
63. those channels active in your Set the Time Zone VCR channel list 1 Press MENU on the remote control to display the VCR Main You can still access channels not Menu on the channel list by using the number buttons on the remote control SETTING UP THE VCR VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 3 to display TIME menu TIME Set Time and Date Auto Clock Set ON Set Time Zone Set Daylight Savings XDS Time Data was found on channel 20 0 Exit 3 Press 3 to display the SET TIME ZONE screen SET TIME ZONE What is your Time Zone Eastern Central Mountain Pacific Alaska Hawaii 7 gt Automatic Press MENU to continue 4 Select your time zone then press MENU to continue If you chose Automatic for your time zone the VCR sets the clock using the first Coordinated Universal Time information it finds If the time is not correct select another time zone or manually set the time and date through the menu system Auto Clock Information Set Daylight Saving Time With a cable box the VCR will not ac op HERO edin tie ER WUAIN ENG reset the clock after a power outage Ss toalspiay the unless the cable box is set to the channel carrying the XDS signal VCR MAIN MENU VCR Plus Timer Recordings Time Channels If Auto Clock Set is unsuccessful try tuning the VCR or cable box to a channel carrying the broadcast information usually PBS t
64. ting your VCR 4 46 Connections 45 A V cable 47 TV with A V jacks 49 TV with A V jacks cable box unscramble 50 TV with RF jack only 48 two VCRs 32 Copying and editing tapes 32 D Daylight saving time 14 E Eject 24 EnergySaver 19 Express Recording XPR 26 F F ADV button 22 Forward and reverse search 39 Frame advance 40 Front panel diagram 52 Front panel display feature 20 FWD button 52 G GO BACK button 22 Go To Search 41 INDEX Index search 42 Indicator Panel 52 INFO button 22 INPUT button 22 31 J Jacks ANT IN 54 Audio Video A V 54 RF OUT 54 L Language feature 8 LINE indicator 31 Locking feature 42 M MENU button 6 9 22 N Number buttons 6 15 22 O On screen Displays 43 Overheating 45 P PAUSE button 22 Picture search options 39 PLAY button 22 52 Plugging inthe VCR 4 POWER button 24 52 Power surges 45 Pro Tect Plus Locking 42 Problem solving 55 R REC button 22 Reception STEREO MONO SAP 31 RECORD button 31 52 Recording 24 audio only 31 broadcast stereo TV 31 copying and editing tapes 32 Express XPR 26 SAP 31 speeds 20 timer 27 VCR Plus 28 XPR Express 26 Remote installing batteries 4 Remote Control Option 18 Remote sensor 52 Remote VCR1 VCR2 option 18 Removing adding channels 12 REV button 22 52 Reviewing programs 30 Rewind automatic 24 RF OUT jack 5 54 71 INDEX S Safety tab 24 Search forward and reverse 39 f
65. tting Up the Channel List 000 30 Using the VCR Plus System eee 30 Stopping a Timer Recording 0000 32 Reviewing and Clearing Programs 32 Recording Broadcast Stereo TV Or SAP Second Audio Program ccsceeeeeeeeees 33 Recording Audio Only ccceccseeeeeeeeeeeeeeneeeeeees 33 Playing Back Audio Only eeceeeeeeeeeeeeeees 34 Using Two VCRs For Copying and Editing TADGS viscscieetiiecaendesteneneatneathesteetbeces 34 TABLE OF CONTENTS Program the Remote ceeeeeeereeees 35 Programming the Remote to Control a TV 36 Operating the TV icaceccAstt ack 36 OTHER FEATURES ccccssssseeessssteeeeessneeeees 39 COMMERCIAL ADVANCE cccccsssseeeesssteeteesssees 40 Markhor naana eet n R ERRET 41 Playpack aa aaa ean aaa a aieiaa 42 Display erana ai a a a aaa 42 MOVIE ADVANCE nnsssssoesnsosennessoorrnnserensesrrensrrrenne 43 Picture Search Options c ccceeeeeceeeeeeeeeeeeeeees 45 Forward and Reverse Search ccccccseeeee 45 Slow Motio her pnn a cee aie 45 Frame Advance cc cccccceeeesseesenneeeeeeeeseeseees 46 WAGER Searchin renr R 46 GO TO Search naiari ira en eiea 47 TRACKING rii rn a a A Ea EE 47 Pro Tect Plus Locking Feature s es 48 Time COUNTER Asrperastiranieuna annaia NARRE TERRENS 48 On screen Displays c csccceeeeseeceeeeeeeeeeeeeeeeees 49 Audio Set up Features s
66. ured under the license from Gemstar Development Corporation VCR Plus Interactive Program Guide System Recording Clock must be set correctly Insert a tape with the safety tab in place and enough tape to record the program The TIMER indicator appears in the display when you turn off the VCR and a timer recording has been set It flashes if there is no tape in the VCR PROGRAMS OVERLAP appears if you have entered two programs where the times overlap UNRECOGNIZED NUMBER PLEASE RE ENTER appears when the VCR does not recognize the PlusCode programming system number Timer recordings will not be lost in the event of an extended power outage 31 RECORDING 32 STOPPING A TIMER RECORDING To stop or cancel a timer recording in progress even an express recording e Press and hold the STOP button for three seconds REVIEWING AND CLEARING PROGRAMS To review programs that you have already set up 1 Press 2 when the VCR MAIN MENU is displayed to display the TIMER RECORDINGS menu TIMER RECORDINGS 1 Create a New Program 2 Review Existing Progs 3 Use VCR Plus Code 2 Press 2 to display the Review Existing Progs screen Program 1 One Time Channel 104 Cable Start Time 08 00 PM End Time 09 30 PM Start Date 11 18 99 Thu Tape Speed SLP Press CLEAR to erase Press MENU for next prog 3 Press CLEAR to erase or MENU to see the next program RECORDING BROADCAST STEREO TV OR SAP SECON
67. utton on the Channel on the TV TV Remote Number VIDEO VID 1 00 SIGNAL LINE 90 VID 1 VID 91 VID 2 VIDEO 92 S VID S VID 93 S VIDEO INPUT S VIDEO SOURCE AUX 68 APPENDIX REFERENCE LIMITED WARRANTY What your warranty covers e Any defect in materials or workmanship For how long after your purchase e Ninety days for labor charges e One year for parts The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm whichever comes first What we will do e Pay any Authorized RCA VCR Service Center the labor charges to repair your VCR e Pay any Authorized RCA VCR Service Center for the new or at our option refurbished replacement parts required to repair your VCR How you get service e Take your VCR to any Authorized RCA VCR Service Center To identify your nearest Authorized RCA VCR Service Center ask your dealer look in the Yellow Pages or call 1 800 336 1900 e Show the Authorized Service Center Representative your evidence or purchase date or first rental e Pick up your VCR when repairs are completed What your warranty does not cover e Customer instruction Your Owner s Manual clearly describes how to install adjust and operate your VCR Any additional information should be obtained from your Dealer e Installation and related adjustments e Signal reception problems not caused by your VCR e Damage from misuse or neglect
68. ve only the time counter remain 2 0 30 00 on the screen HOURS _ MINUTES 3 Press INFO again to remove the time counter from the screen SECONDS Turning off the VCR also resets the displays AU D l O s ET U P F EATU R E s Time counter only does not time out The audio set up features enhance your tape playback and recordings The features in this section are accessed through the AUDIO menu and are shown in the displays below 1 Press MENU to display the VCR MAIN MENU VCR MAIN MENU VCR Plus Timer Recordings Time Channels Preferences Audio Language Exit 2 Press 6 to display AUDIO menu AUDIO 1 Reception STEREO 2 Tape Playback HI FI Now you are ready to select an item from the menu to set up To receive Hi Fi stereo sound use audio video cables with a compatible TV or receiver Using only the RF OUT jack will not produce stereo sound 49 OTHER FEATURES RECEPTION Some TV programs are broadcast with stereo audio or a Second Audio Program SAP which offers a second language The reception feature lets you select the type of audio you want to record Press 1 to switch between Reception STEREO MONO and SAP e Select STEREO for normal or stereo broadcast TV recording e Select MONO if the stereo signal is weak and the sound is too noisy e Select SAP to record a Second Audio Program instead of normal audio on both the Hi Fi and linear tracks TAPE PLAYBACK The VC

RCA VR646HF VCR User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents