Raymarine 125 GPS Receiver User Manual
Contents
1. installation This equipment must be installed and operated in accordance with the instructions contained in this handbook Failure to do so could result in poor product performance personal injury and or damage to your boat WARNING Electrical safety Make sure the power supply is switched off before you make any electrical connections WARNING Lithium battery This unit has a lithium battery fitted DO NOT attempt to recharge this battery DO NOT incinerate this battery Ensure you follow local regulations when disposing of this unit Where can install the unit No trip or tread In the 3 ON D the mast Acon the beam O Radar A srove the beam X Clear view of the sky VHF Radio and other antenna A Minimum 1 0 m 3 ft D7472_2 To mount the unit on a pole Securely attach the pole mount base to a suitable pole Pass the cable and connector through either a the center of the pole mount bracket and the pole or b the cable exit hole alongside the center hole Attach the connector securely to the plug in the base of the unit Secure the receiver to the pole mount base using the screws provided Notes 1 To mount the receiver on a pole you will need a pole of suitable length with a 1 inch 14 TPI thread not exceeding 20mm in length 2 To rail mount the receiver you w2. Raystar 125 GPS Receiver Raymarine Owner s Handbook Wwww raymarine com Welcome to the Raystar RS125 GPS Receiver Your handbook contains an explanation of how to install operate and maintain your Raystar RS125 GPS Receiver Intended Use This product is a GPS antenna with a built in position fixing receiver using either NMEA0183 Version 2 3 or later or Raymarine SeaTalk data output The intended application is for leisure marine boats and workboats not covered by IMO SOLAS carriage requirements What s in the box Part No R38103 Part No R38104 Raystar RS125 GPS Receiver 10m 33ft NMEA SeaTalk connection cable Part No E35018 Pole mount kit O Sa Thumb nuts x2 P way Flush mount gasket f g Scotchlok sudh gt connectors x5 The Raystar RS125 GPS Receiver has no user serviceable parts tuds x2 crews x2 What tools do I need to install it 2 1 4 in Drill bit 20mm 13 16 in Drill bit Phillips screwdriver Adhesive tape D7471_2 A Safety notices WARNING Navigation aid Although this product has been designed to be accurate and reliable many factors can affect its performance As a result it should only be used as an aid to navigation and should never replace common sense and navigational judgement Always maintain a permanent watch so you can respond to situations as they develop WARNING Product
3. ddition our policy of continuous product improvement may change specifications without notice As a result Raymarine cannot accept liability for any differences between the product anthe handbook D7476_2 To get Technical Support Www raymarine com United States Raymarine Technical Support 1 800 539 5539 extension 2444 or 603 881 5200 Product Repair and Service Raymarine Product Repair Center 21 Manchester Street Merrimack NH 03054 4801 1 800 539 5539 Opening hours Monday through Friday 0815 1700 Eastern Standard or Eastern Daylight Savings Time Help us to help you Europe Technical Support Services Accessories Raymarine UK Limited Anchorage Park Portsmouth PO3 51D England Tel 44 0 23 9271 4713 Fax 44 0 23 9266 1228 When requesting service please quote the following product information Equipment type Model number e Serial number D74771 Raymarine UK Limited Quay Point Northarbour Road Portsmouth Hampshire England PO6 3TD Tel 44 0 23 9269 3611 Fax 44 0 23 9269 4642 www raymarine com 21 Manchester Street Merrimack NH 03054 USA Tel 603 881 5200 Fax 603 864 4756 Raymarine Incorporated 4801 www raymarine com Raymarine Document No 81247_3 Date April 2005 Raymarine 2005
4. ich this declaration relates is in conformity with the essential requirements of European Parliament and Council Directive 1999 5 EC on radio equipment and on telecommunication terminal equipment and the mutual recognition of their conformity Product name Raystar 125 GPS Receiver Product number E32042 This product has been assessed to Conformity Procedure Annex IV of the Directive The assessment is consistent with a Technical Construction File showing conformity with the essential requirements of the Directive and has been reviewed by Notified Body No 0191 Signed lt td A Abbas International Compliance Manager Raymarine Ltd 21st January 2005 CE conformity This product is labeled with the CE conformity mark CE 0191 SiRF Technology Inc This product uses certain elements of software supplied to Raymarine by SiRF Technologies Inc For full details of their licensing agreement refer to our website at www raymarine com Warranty To register your new Raymarine product please take a few minutes to fill out the warranty card It is important that you complete the owner information and return the card to us to receive full warranty benefits Your product can also be registered via our web site www raymarine com Handbook information To the best of our knowledge the information contained in this hadbook was correct as it wento press Raymarine cannot accept any liability for any inaccuracies or ommissions it may contain In a
5. ill need to purchase a suitable rail mount bracket To flush mount the unit Use the template supplied in this handbook to mark the two fixing holes and the center hole Drill the holes using the drill sizes shown on the template Screw the two fixing studs into the underside of the receiver unit Place the waterproof gasket into position on the underside of the receiver Attach the connector securely to the plug in the base of the unit and pass the cable through the center hole on the mounting surface Carefully position the receiver so that the mounting studs pass through the holes in the mounting surface Secure the receiver to the mounting surface using the two thumb nuts these should be hand tight only D7473_2 To connect the RS125 using Scotchlok connectors Using suitable wire clippers remove the tinned ends from the individual cables Leave the insulation intact Place the wires to be joined into the connectors ensuring correct polarity and that the wires are fully pushed home Using a pair of pliers crimp the connector bulb together ensuring that a secure connection has been made Ensure the cables are secured in a suitable position to prevent the joint being placed under strain To connect to NMEA 0183 Red 12 32 V Yellow NMEA out Brown RTCM in Green NMEA in Shield OV ground NMEA sentence
6. is MEDIUM Adjustment of the SOG COG filter is made from your system display For full details of how to adjust the SOG COG filter refer to the relevant Manufacturer s manual Accessories You can obtain the following accessories to help you quickly and easily connect your RS125 to existing equipment E36013 600mm Antenna conversion cable The antenna conversion cable enables you to connect your RS125 receiver to an existing RS120 RS112 or RS114 cable saving the time and trouble of running a new cable E36014 1000mm Display conversion cable The display conversion cable enables you to quickly connect your RS125 receiver to an existing RC425 or RC420 display saving time and trouble D7687_2 Important Information EMC conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment The design and manufacture of Raymarine equipment and accessories conforms to the appropriate Electromagnetic Compatibility EMC standards but correct installation is required to ensure that performance is not compromised For full details and installation guidelines refer to or web site at www raymarine com Declaration of conformity We Raymarine Limited Quay Point Portsmouth Hampshire England PO6 3TD declare under our sole responsibility that the product identified in this declaration and to wh
7. s Output sentences GPGGA GPGSA GPGSV GPGLL GPRMC GPDTM GPGNS GPVTG PRAYA Input sentences PRAYI PRAYE PRAYA Note If the Brown RTCM and Green NMEA in wires are not used they must be suitably grounded If you do not have a breaker in the power circuit an in line 0 5 A quick blow fuse should be fitted to the positive red lead of the cable To connect to SeaTalk Red 12 V Yellow Sealalk input output Brown RTCM in Green connect with Red 12V wire Shield 0 V ground Note If the Brown RTCM wire is not used it must be suitably grounded to 0 Volts If you do not have a breaker in the power circuit an in line 0 5 A quick blow fuse should be fitted to the positive red lead of the cable D7474_2 To connect to a C Series or E Series display using SeaTalk C Series C Series SeaTalk Pigtail RS125 GPS g Receiver cable Part No R08050 Scotchlok connectors E Series RS125 GPS E Series SeaTalk Pigtail Receiver cable Part No E55054 To external alarm In SeaTalk network installations containing other power devices in addition to your Raystar 125 GPS receiver e g ST series instruments autopilot controllers etc you shoud not fix the red wire on your C Series SeaTalk pigtail to the GPS receiver or overall SeaTalk network If you are not using a land based DGPS antenna on your Raystar 125 GPS receiver most installation
8. s do not you should connect the brown RTCM input to the shield wire ground This will prevent outside RF energy from inadvertently injecting noise into the system To connect to a Personal Computer using NMEA m Scotchlok connectors RS125 GPS Receiver cable 9 pin Serial Cable Part No E86001 If you are connecting your RS 125 GPS receiver to a PC you will need a Serial Data Cable Part No E86001 Connect the Yellow from the RS 125 to the Yellow of the Serial Data Cable Connect the Red from the RS 125 to the positive of your boat s 12 V DC power supply Connect the Brown Green and Shield from the RS 125 and a Black from the Serial Data Cable to your boat s ground D7918_1 What do the lights mean Flashing RED Unit is in bootcode either being upgraded N or unable to boot Flashing ORANGE Unit is running but does not have a fix Flashing GREEN Unit is running and has a fix 1 flash every 2 seconds indicates NMEA connection 1 flash every 4 seconds indicates SeaTalk connection SOG COG filter The integral SOG COG filter fitted to your RS125 compensates for the oscillating motion of your boat to give a clearer indication of the boat s course and speed Slow moving boats or boats sailing in rough seas will benefit from a high filter setting whereas a powerboat that can quickly change speed and direction will benefit from a low setting The default setting for your RS125
Download Pdf Manuals
Related Search