Quantum 06 edge va Wheelchair User Manual
Contents
1. PROHIBITED Never use an extension to plug in your battery charger Plug the SN charger directly into a properly wired standard electrical outlet PROHIBITED Do not allow unsupervised children to play near the power chair while the batteries charging Pride recommends that do not charge the batteries while the power chair is occupied A MANDATORY Read the battery charging instructions in this manual and in the U manual supplied with the battery charger before charging the batteries WARNING Explosive gases be generated while charging the batteries Keep the power chair and battery charger away from sources of ignition such as flames or sparks and provide adequate ventilation when charging the batteries WARNING You must recharge the power chair batteries with the supplied off board battery charger Do not use an automotive type battery charger WARNING Inspect the battery charger wiring and connectors for damage before each use Contact your authorized Quantum Rehab Provider if damage is found WARNING Do not attempt to open the battery charger case If the battery charger 2 does not appear to be working correctly contact your authorized Quantum Rehab 7 4 Provider WARNING Be aware that the battery charger case may become hot during charging Avoid skin contact and do not place on surfaces that may be affected by heat WARNING If the battery charger is equipped with c2. 3 Check the joystick operation and the brakes before using your power chair again 4 If any inconsistencies found take your power chair to a Quantum Rehab Provider Power chairs that are frequently exposed to sources of water such as incontinence should be inspected often for corrosion and electronic components may need to be replaced frequently Temperature Some of the parts of your power chair are susceptible to extreme changes in temperature Always keep your power chair between the temperatures of 18 F 8 C and 122 F 50 C In extremely cold temperatures the batteries may freeze The specific temperature at which they freeze depends on a number of factors such as battery charge usage and composition of the batteries e g AGM or Gel Cell Temperatures above 122 F 50 C may cause your power chair to operate at a reduced speed This reduced speed is a safety feature built into the controller that helps prevent damage to the motor and other electrical components General Guidelines Avoid knocking or bumping the controller especially the joystick Avoid prolonged exposure of your power chair to extreme conditions such as heat cold or moisture Keep the controller clean Check all connectors to ensure that they are all tight and secured properly Make sure pneumatic tires are inflated to the psi bar kPa air pressure rating indicated on the tire WARNING Make sure your tires are inflated to the psi bar
3. Daily Checks With the controller turned off check the joystick Make sure it is not bent or damaged and that it returns to the neutral position when you release it Check the rubber boot around the base of the joystick for damage Visu ally inspect the boot Do not handle or try to repair it See your Quantum Rehab Provider if there is a problem Visually inspect the controller harness Make sure that it is not frayed cut has any wires exposed See your Quantum Rehab Provider if there is a problem Check for flat spots on solid tires Flat spots could adversely affect stability Inspect the seating system armrests and front riggings for loose hardware stress points or damage See your Quantum Rehab Provider if there is a problem Weekly Checks Disconnect and inspect the controller from the power base Look for corrosion Contact your Quantum Rehab Provider if necessary Ensure that all parts of the controller system are securely fastened to your power chair Do not overtighten any screws Check for proper tire inflation Pneumatic tires should be inflated to the psi bar kPa air pressure rating indi cated on each tire If a tire does not hold air see your Quantum Rehab Provider for replacement of the tube Check the brakes This test should be carried out on a level surface with at least 3 feet 1 meter of clearance around your power chair To check the brakes 1 Turn on the controller and turn down the speed leve
4. Q6 Edge OWNER S MANUAL Pride Mobility Products Corp www pridemobility com SAFETY GUIDELINES IN WARNING A Quantum Rehab Provider or a qualified technician must perform the initial setup of 2 this power chair and must perform all of the procedures in this manual a gt The symbols below are used throughout this owner s manual and on the power chair to identify warnings and important information It is very important for you to read them and understand them completely J WARNING Indicates a potentially hazardous condition situation Failure to follow designated 2 procedures can cause either personal injury component damage or malfunction On the N product this icon is represented as a black symbol on a yellow triangle with a black border N MANDATORY These actions should be performed as specified Failure to perform mandatory actions can cause personal injury and or equipment damage On the product this icon is A represented as a white symbol on a blue dot with a white border or in any circumstances Performing a prohibited action can cause personal injury and or equipment damage On the product this icon is represented as a black symbol with a red circle S PROHIBITED These actions are prohibited These actions should not be performed at any time and red slash INTENDED USE The intended use of the Pride Mobility Products device is to provide mobility to persons limited to a seated posi
5. Locate the two armrest knobs on each side of the armrest receiver bracket See figure 15 2 Loosen the knobs 3 Slide the armrests in or out to the desired width 4 Tighten the knobs Armrest Angle Adjustment To change the armrest angle 1 Lift the armrest straight up so that it is perpendicu lar to the floor See figure 15 2 Loosen the jam nut 3 Turn the adjusting screw to raise or lower the front of the armrest 4 Tighten the jam nut to lock the adjusting screw into place Armrest Height Adjustment To change the armrest height 1 Loosen the two setscrews located on the armrest receiver See figure 15 2 Raise or lower the armrest to the desired height 3 Tighten the setscrews to secure the armrest JAM NUT ARMREST ANGLE ADJUSTING SCREW ARMREST HEIGHT ADJUSTING SETSCREWS SEATBACK ANGLE ADJUSTING SCREW ARMREST KNOB Figure 15 Seatback Armrest Adjustment 18 www pridemobility com Q6 Edge VA V COMFORT ADJUSTMENTS Controller Position You can move the controller in toward or out away from the armrest or change the position of the control ler for either left hand or right hand use WARNING Do not place the controller 2 harness so that it can be pinched in the a seat frame or the power base frame CONTROLLER BRACKET To extend the controller k 1 Flip up the armrest so it is perpendicular to the ASRS floor 2 Loosen the setscrew on the controller brac
6. SEAT INTERFACE MANDATORY If your power chair is equipped with a transit securement system and any adjustment to the seat height or seat angle is necessary gt contact your Quantum Rehab Provider These comfort adjustment can only be made by a Quantum Rehab Provider HARDWARE To change the seat height 1 Turn off the power to the controller 2 Make sure the power chair is in drive mode Figure 13 Seat Height Angle Adjustment UMS 3 Unplug the controller connector s from the power base See figure 3 4 Flip up the seat latch safety See figure 7 Squeeze the seat latch and release the seat from the front trapeze bar 6 Slide the seat forward and remove it from the power base 16 www pridemobility com Q6 Edge VA V COMFORT ADJUSTMENTS 7 Remove the hardware that attaches the trapeze bars to the seat interface weldments See figure 13 8 Move the trapeze bars up or down to the desired height NOTE Change the seat dump by raising or lowering only one trapeze bar front or rear 9 Reinstall the hardware 10 Reinstall the seat 11 Reconnect the controller to the power base Seat Position You can move the seat forward or rearward by chang ing the extrusion mounting position To change the position 1 Turn off the power to the controller 2 Make sure the power chair is in drive mode 3 Unplug the controller connector s from the power base 4 Remove the seat from the
7. Vil CARE AND MAINTENANCE Storage Your power chair should be stored in a dry place free from temperature extremes When storing disconnect the batteries from the power chair See VI Batteries and Charging Y N WARNING If you fail to store the unit properly the frame can rust and the electronics can be 2 damaged Any corroded electronic connection should be replaced Batteries that are regularly and deeply discharged infrequently charged stored in extreme temperatures or stored without a full charge may be permanently damaged causing unreliable performance and limited service life It is recommended that you charge the batteries periodically throughout periods of prolonged storage to ensure proper performance You may wish to place several boards under the frame of your power chair to raise it off of the ground during periods of prolonged storage This takes the weight off the tires and reduces the possibility of flat spots developing on the areas of the tires contacting the ground Disposal of Your Power Chair Your power chair must be disposed of according to applicable local and national statutory regulations Contact your local waste disposal agency or Quantum Rehab Provider for information on proper disposal of power chair packaging metal frame components plastic components electronics batteries neoprene silicone and polyurethane materials Cleaning and Disinfection Use a damp cloth and mild non ab
8. all controller connections to the power base Make sure they are secured properly Check the brakes See VII Care and Maintenance Check battery charge See VI Batteries and Charging Ensure the manual freewheel levers are in drive mode before sitting on the power chair NOTE If you discover a problem contact your Quantum Rehab Provider for assistance 6 www pridemobility com Q6 Edge VA lll YOUR POWER CHAIR THE Q6 EDGE VA POWER CHAIR Your power chair has two main assemblies the seat assembly and the power base assembly See figure 1 Typically the seat assembly includes the armrests seatback and seat base The power base assembly includes two motor brake assemblies two drive wheels four caster wheels two batteries and wiring harnesses See figures 1 2 and 3 SEATBACK SEAT ASSEMBLY ARMREST ES JOYSTICK CONTROLLER SEAT BASE POWER BASE ASSEMBLY PR 7 TA N X NAS AN SA 9156 25 D A DS CASTER WHEEL a el N MANUAL FREEWHEEL LEVER FRONT RIGGING DRIVE WHEEL NANI spring shockicas FOOT PLATFORM SHOWN DAMPER LOCATION CASTER WHEEL Figure 1 The Q6 Edge VA Power Chair Synergy Seat Shown Q6 Edge VA www pridemobility com 7 lll YOUR POWER CHAIR REAR SHROUD TRAPEZE BARS FRONT COVER ee SUSPENSION SPRING Figure 2 06 Edge VA Power Base PROHIBITED The spring tension on your power chair
9. kPa air pressure rating indicated on the AN tire for pneumatic tires Do not underinflate or overinflate your tires Low pressure may result in S N loss of control and overinflated tires may burst Overinflating tires can cause them to explode WARNING Do not use a high pressure hose to inflate your tires Use arubber conditioner on the tire sidewalls to help preserve them TN Y NW WARNING Never use a rubber conditioner on the tread area of the tires doing so may make the 4 N tires slippery and cause your power chair to skid All wheel bearings prelubricated and sealed They require no subsequent lubrication Q6 Edge VA www pridemobility com 27 Vil CARE AND MAINTENANCE The body shroud has been sprayed with a clear sealant coating You can apply a light coat of car wax to help it retain its high gloss appearance Check all electrical connections Make sure they are tight and are not corroded Batteries must sit flat within the battery tray with the battery terminals facing rearward Refer to the battery wiring label for the correct wiring layout WARNING Even though the power chair has passed the necessary testing AN requirements for ingress of liquids you should keep electrical connections away 2 N S from sources of dampness including direct exposure to water or bodily fluids and N gt M incontinence Check electrical components frequently for signs of corrosion and replace as necessary
10. the vehicle manufacturer WARNING The positioning belt should be secured at all times Never allow the positioning belt to hang or drag on the floor as it may become entangled To install the positioning belt Figure 19 Positioning Belt Adjustment 1 Remove the rearmost screw that holds the seat hinge to the seat base on both the left and right seat hinges 2 Insert the screw through the supplied washer through the positioning belt and into the seat base for each side ofthe power chair seat 3 Tighten both screws To adjust the positioning belt for operator comfort 1 Once seated insert the metal tab on one side of the belt into the plastic housing on the opposite side until you hear a click See figure 19 2 Pull the excess strap attached to the metal tab until it is secure but not so tight as to cause discomfort To release the positioning belt 1 Press the push button mechanism on the plastic housing MANDATORY Make sure the positioning belt is properly secured to the power chair and is adjusted for operator comfort before each use G MANDATORY Inspect the positioning belt for loose parts or damage including tears worn x y spots bent hardware damaged latch mechanisms dirt or debris before each use of the power chair If discover a problem contact your Quantum Rehab Provider for maintenance and repair 22 www pridemobility com Q6 Edge vi BATTERIES AND CHARGING BATTERIES AND CHA
11. was factory set to meet the needs of the demographic majority of users Do not adjust the tension of any spring on your power chair Electrical Components The electrical components consist of the controller assembly the batteries and the motors The batteries motors and controller power module if equipped are located on the power base assembly The controller is located on the seat assembly Connectivity between the controller and the motors batteries and the battery charger is pro vided by one or more wiring harnesses See figure 3 Controller Harness Connector The controller harness connector is where the controller plugs into the power base Each controller uses a different type of harness Regardless of which type of controller is used the harness must be secured to the seat assembly and not allowed to drag on the floor Motor Connectors This is where the controller connects to the motors Battery Connector This is where the controller connects to the batteries Controller Power Module This enables the controller to communicate with the batteries and the motors 8 www pridemobility com Q6 Edge VA lll YOUR POWER CHAIR Main Circuit Breaker located on the rear main frame The main circuit breaker is a safety feature built into your power chair When the batteries and the motors are heavily strained e g from excessive loads the main circuit breaker trips to prevent damage to the motors and the electronics If the cir
12. NING sure tighten the fasteners so that the connections secure 8 Connect the battery harness to the new rear battery according to the battery wiring diagram See figure 23 9 Install the new batteries and connect the quick release battery connectors 10 Reinstall the front cover and foot platform 11 Charge the batteries See VI Batteries and Charging SET CONFIGURATION POSITIVE RED TERMINAL POST NEGATIVE BLACK TERMINAL POST CONNECT RED WIRES TO RED POSITIVE TERMINAL POSTS CONNECT BLACK WIRES TO BLACK NEGATIVE TERMINAL POSTS FRONT COVER QUICK RELEASE BATTERY CONNECTORS REAR BATTERY FRONT BATTER Figure 23 Battery Installation Q6 Edge VA www pridemobility com 31 Vil CARE AND MAINTENANCE When to See Your Quantum Rehab Provider for Service The following symptoms could indicate a serious problem with your power chair If necessary contact your Quantum Rehab Provider When calling have the model number serial number nature of the problem and the error code if available Motor noise Frayed harnesses Cracked or broken connectors Uneven wear on any of the tires Jerky motion Pulling to one side Bent or broken wheel assemblies Does not power up Powers up but does not move Loose seat or seating components Corrective Maintenance Ifthe battery condition meter does not light up when you tur
13. Q6 Edge VA Vil CARE AND MAINTENANCE CARE AND MAINTENANCE Your 06 Edge is a sophisticated power chair Like any motorized vehicle it requires routine maintenance checks You can perform some of these checks but others require assistance from your Quantum Rehab Provider Preventive maintenance is very important If you follow the maintenance checks in this section as scheduled you can help ensure that your power chair gives you years of trouble free operation If you have any doubt as to your power chair s care or operation contact your Quantum Rehab Provider 2 WARNING Do not service the power chair when the seat is occupied 7 ti j Your power chair like most electrical equipment is susceptible to damage from the elements Avoid damp areas of any kind a WARNING Direct or prolonged exposure to water or dampness could cause the power y N R de chair to malfunction electronically mechanically Water cause electrical 2 N components to corrode and the chair s frame to rust Power chairs should examined N y periodically for signs of corrosion caused by water exposure bodily fluid exposure or incontinence Damaged components should be replaced treated immediately Should your power chair come in contact with water 1 Dry your power chair as thoroughly as possible with a towel 2 Allow your power chair to sit in a warm dry place for 12 hours to allow unseen water to evaporate
14. RGING Edge VA uses two long lasting 12 volt deep cycle batteries These batteries are sealed and maintenance free Since they are sealed there is no need to check the electrolyte fluid level Deep cycle batteries are designed to handle a longer and deeper discharge Though they are similar in appearance to automotive batteries they are not interchangeable Automotive batteries are not designed to handle a long deep discharge and also are unsafe for use in power chairs MANDATORY Battery posts terminals and related accessories contain lead and lead compounds Wear goggles and gloves when handling batteries and wash hands e 20 after handling WARNING Contact your Quantum Rehab Provider if you have any questions 2 2 regarding the batteries in your power chair PROHIBITED Always use two batteries of the exact same type chemistry and amp san san Ah hour Ah capacity Refer to specifications table in this manual and in the manual supplied with the battery charger for recommended type and capacities The battery charger is essential in providing long life for your power chair batteries It is designed to optimize your power chair s performance by charging the batteries safely quickly and easily necessary properly install an approved 3 pronged adapter to an electrical outlet amp PROHIBITED Removal of grounding prong can create electrical hazard If having 2 pronged plug access
15. Y Battery posts terminals and related accessories contain lead and iaa Y lead compounds Wear goggles and gloves when handling batteries and wash hands ea after handling WARNING The batteries in your power chair should only be serviced or replaced by an authorized Quantum Rehab Provider or a qualified technician WARNING Do not replace batteries when seat is occupied y WARNING Power chair batteries are heavy See specifications table If K S unable to lift that much weight be sure to get help Use proper lifting techniques and avoid lifting beyond your capacity WARNING Do not mix old and new batteries Always replace both batteries at the same time M NI PROHIBITED Keep tools and other metal objects away from the battery terminals j Contact with tools can cause electrical shock 4 30 www pridemobility com Q6 Edge VA Vil CARE AND MAINTENANCE To replace the batteries 1 Turn off the power to the controller 2 Make sure that the power chair is in drive mode See Your Power Chair 3 Remove the front cover by squeezing the release handles see figure 23 and lifting the foot platform bracket up and away from the power base Disconnect the quick release battery connectors See figure 23 Remove the batteries Disconnect the battery harness from each battery Connect the battery harness to the new front battery according to the battery wiring diagram See figure 23 WAR
16. arger from the electrical outlet and then from the controller Battery Break in To break in new batteries for maximum efficiency 1 Fully recharge any new battery prior to its initial use This brings the battery up to about 90 of its peak performance level 2 Operate your power chair throughout the house and yard Move slowly at first and do not travel too far until you become accustomed to the controls and break in the batteries 3 Give the batteries another full charge of at least 8 to 14 hours and operate your power chair again The batteries will now perform at over 90 of their potential 4 After four or five charging cycles the batteries will top off at 100 charge and last for an extended period Frequently Asked Questions FAQs How does the charger work The battery charger takes the standard electrical outlet voltage of 120 VAC alternating current and converts it to 24 VDC direct current The power chair batteries use direct current to run your power chair When the battery voltage is low the charger works harder to charge the battery As the battery voltage approaches full charge the charger does not work as hard to complete the charging cycle When the battery is fully charged the amperage from the charger is nearly at zero This is how the charger maintains a charge but does not overcharge the battery Can I use a different battery charger You should use the charger supplied with the power chair It is the safest
17. cuit trips allow your power chair to rest for approximately one minute Next push in the circuit breaker button turn on the controller and con tinue normal operation If the main circuit breaker continues to trip repeatedly contact your Quantum Rehab Provider CONTROLLER POWER MODULE CONTROLLER CONNECTOR TO BATTERY CONNECTORS TO MOTOR MAIN CIRCUIT CONNECTOR BREAKER TO MOTOR CONNECTOR QUICK RELEASE BATTERY CONNECTORS Figure 3 Q6 Edge VA Electrical Components Q6 Edge VA www pridemobility com 9 lll YOUR POWER CHAIR Manual Freewheel Levers For your convenience your power chair is equipped with a manual freewheel lever mounted on each motor The levers allow you to disengage the drive motors and maneuver the chair manually WARNING The power chair could roll unintentionally when the drive motors are 8 ES disengaged on an incline Property damage severe injury or death can occur WARNING This chair IS EQUIPPED with an audible or visible warning system to alert the user when one or both drive motors are disengaged WARNING The power chair can drive in circles when only one drive motor is engaged DO NOT ATTEMPT TO DRIVE IN THIS CONDITION Property damage severe injury or death can occur WARNING Ensure both drive motors are engaged before turning on power to the controller or attempting to drive the power chair WARNING Do not attempt to use the power chair or occupy the cha
18. dth or seat depth The two main components are alu minum extrusions mounted to the seat base These extrusions attach to a pair of trapeze bars that are mounted to the power base See figure 7 For occupied transit power chairs the seat plate is secured to the four seat mounting brackets on the power base The seat plate is located on the bottom of the seat See figure 9 NOTE If your power chair is equipped with a Spe cialty Seat Synergy Seat or a TRU Balance Power Positioning System refer to the information provided in separate manuals A WARNING Do not pick up the seat 2 frame by the armrests They are free to 2 N pivot and you may lose control of the seat if they do so To install the seat UMS 1 Tilt the seat back and slide the rear extrusion onto the rear trapeze bar See figure 7 2 Lower the front extrusion onto the front trapeze bar until the seat locks into place 3 Flip the seat latch safety down 2 safety is flipped down before using your power chair AN WARNING Make sure the seat latch 4 Install the controller and route the harness to the back of the power base See figures 8 or 10 SEAT LATCH SAFETY REAR EXTRUSION gt Q6 Edge www pridemobility com FRONT EXTRUSION TRAPEZE BARS Figure 8 Controller Harness Routing on a Synergy Seat 13 IV ASSEMBLY MANDATORY Prevent controller harness damage Avoid routing the controller harness on the out
19. e VA www pridemobility com 3 1 INTRODUCTION SAFETY WELCOME to Quantum Rehab a division of Pride Mobility Products Pride The power chair you have pur chased combines state of the art components with safety comfort and styling in mind We are confident that these design features will provide you with the conveniences you expect during your daily activities Once you understand how to safely operate and care for your power chair it should give you years of trouble free operation and service Read and follow all instructions warnings and notes in this manual before attempting to operate your power chair for the first time You must also read all instructions warnings and notes contained in any supplemental instruc tional booklets for the controller front riggings and or seating system that accompanied your power chair before initial operation Your safety depends upon you as well as your provider caretaker or healthcare professional in using good judgement If there is any information in this manual which you do not understand or if you require additional assistance for setup or operation please contact your Quantum Rehab Provider Failure to follow the instructions in this manual and those located on your power chair can lead to personal injury and or damage to the power chair including voiding the warranty PURCHASER S AGREEMENT By accepting delivery of this product you promise that you will not change alter or modify t
20. e user and has assisted the prescribing healthcare professional and or the Quantum Rehab Pro vider in the instruction process for the use of the product There are certain situations including some medical conditions where the power chair user will need to practice operating the power chair in the presence of a trained attendant A trained attendant can be defined as a family member or care professional specially trained in assisting a power chair user in various daily living activities As you begin using your power chair during daily activities you will probably encounter situations in which you will need some practice Simply take your time and you will soon be in full and confident control as you maneuver through doorways on and off of elevators up and down ramps and over moderate terrain Below are some precautions tips and other safety considerations that will help you become accustomed to oper ating your power chair safely Pre Ride Safety Check Get to know the feel of your power chair and its capabilities Pride recommends that you perform a safety check before each use to make sure your power chair operates smoothly and safely Perform the following inspections prior to using your power chair Check for proper tire inflation Maintain but do not exceed the psi bar kPa air pressure rating indicated on each tire if equipped with pneumatic tires Check all electrical connections Make sure they are tight and not corroded Check
21. equipped with a power ele vating seat option While the seat itself may be any one of the styles offered for this model the way the seat base attaches to the power base is different SEAT PLATE INTERFACE BRACKET To install the power elevating seat l Place the seat plate interface bracket onto the actu ator See figure 11 2 Insert the supplied hardware into the actuator and tighten the hardware 3 Place the seating system onto the seat plate and secure 4 Plug in the power seat toggle switch harness if equipped ACTUATOR Transit Securement System Optional If your power chair is equipped with a transit securement system it is equipped with manufacturer installed front and rear securement brackets and positioning belt anchoring brackets See figure 12 Refer to the supplement provided with your power chair for information on how to use the transit securement system ANCHORING BRACKET LOCATIONS 1 OF 2 SHOWN Le SECUREMENT BRACKETS 3 OF 4 SHOWN Figure 12 Transit System Securement Brackets Synergy Seat Shown Q6 Edge VA www pridemobility com 15 V COMFORT ADJUSTMENTS COMFORT ADJUSTMENTS After becoming familiar with your power chair s operation you may find the need to make some adjustments to increase your comfort such as seat height and angle armrest width armrest angle and height foot platform height depth and angle and controller position NOTE If your power chair is equi
22. es are specifically designed to provide power drain down their charge and then accept a relatively quick recharge AGM and Gel Cell batteries should be charged as often as possible They do not have a memory like nickel cadmium batteries We work closely with our battery manufacturer to provide a battery that best suits your power chair s specific demands Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge During shipping the batteries encounter temperature extremes that may influence initial performance Heat robs the charge from the battery and cold slows the power available and extends the time needed to recharge the battery just as with a car battery It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature More importantly it will take a few charging cycles a partial drain then a full recharge to establish the critical chemical balance that is essential to the battery s peak performance and long life It will be well worth it to take the time to break in your battery properly Q6 Edge VA www pridemobility com 25 VI BATTERIES AND CHARGING How can I ensure maximum battery life A fully charged deep cycle battery will provide reliable performance and extended battery life Keep your power chair s batteries fully charged whenever possible Batteries that are regularly and deeply discharged infrequently charged or st
23. form bracket and tighten Foot Platform Depth Adjustment You can adjust the depth of the foot platform To adjust the foot platform depth 1 Remove the hardware from the foot platform bracket See figure 17 2 Move the foot platform in or out to the desired depth 3 Reinstall the hardware into the foot platform bracket and tighten Foot Platform Angle Adjustment You can adjust the angle of the foot platform To adjust the foot platform angle 1 Flip up the foot platform and locate the screw See figure 17 2 Turn the screw to raise or lower the front of the foot platform PLATFORM BRACKET Figure 17 Foot Platform Adjustment 20 www pridemobility com Q6 Edge VA V COMFORT ADJUSTMENTS Power Elevating Seat Optional If your power chair is equipped with a power elevating seat you can change the seat height either through the controller or through a toggle switch mounted to one of the armrests To change the seat height through toggle switch 1 Press forward on the toggle switch to raise the seat See figure 18 2 Pull back on the toggle switch to lower the seat R WARNING Do not allow the motor to A run more than few seconds after the J mechanism reaches the top or bottom limit NOTE For more information on operating the power elevating seat through the controller contact your Quantum Rehab Provider WARNING The power elevating seat option is intended for use on a leve
24. formance and battery life How can get maximum range or distance per charge Rarely do you have an ideal driving situation such as smooth flat hard terrain with no wind hills or curves More often you are presented with hills sidewalk cracks uneven and loosely packed surfaces curves and wind All of these factors will affect the distance or running time per battery charge Below are a few suggestions for obtaining the maximum range per charge Always charge the batteries fully prior to your trip Plan your trip in advance to avoid inclines if possible Limit baggage weight to essential items Try to maintain an even speed and avoid stop and go driving Pride recommends charging your batteries for at least 48 continuous hours once per month to improve battery performance and battery life What type of batteries should I use We recommend deep cycle batteries that are sealed and maintenance free Both AGM and Gel Cell are deep cycle batteries that are similar in performance Refer to the specifications table for more information regarding the batteries used with your power chair WARNING Corrosive chemicals contained in batteries Use only AGM or Gel Cell batteries to reduce the risk of leakage or explosive conditions Why do o my new batteries seem weak Deep cycle batteries employ a much different chemical technology than that used in car batteries nickel cadmium nicads or in other common battery types Deep cycle batteri
25. freewheel mode before performing this procedure WARNING When changing a tire remove only the five lug nuts then remove the wheel If any further disassembly is required deflate the tire completely or it may explode Q6 Edge VA www pridemobility com 29 Vil CARE AND MAINTENANCE FRONT RIM WARNING Completely deflate the tire before attempting repair Figure 21 06 Edge VA Drive Wheel Figure 22 Q6 Edge VA Drive Wheel Disassembled Follow these easy steps for a quick and safe repair for both pneumatic and solid tires Turn off the power to the controller Set the power chair up on blocks If you are changing a pneumatic tire completely deflate it before removing the wheel Remove the 5 lug nuts from the wheel hub See figure 21 Pull the wheel off of the hub Remove the screws and separate the front and rear rim See figure 22 Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid tire 8 Screw together the two rim halves 9 Slide the wheel back onto the hub 10 Reinstall the five 5 lug nuts onto the wheel hub and tighten 11 Inflate the pneumatic tire to the psi bar kPa air pressure rating indicated on each tire 12 Remove the power chair from the blocks AA DS Battery Replacement A battery wiring diagram is printed on a decal located on the front cover See the specification table for correct battery specifications Pb Y MANDATOR
26. his product or remove or render inoperable or unsafe any guards shields or other safety features of this product fail refuse or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product SHIPPING AND DELIVERY Before using your power chair make sure your delivery is complete as some components may be individually packaged If you do not receive a complete delivery please contact your Quantum Rehab Provider immediately Where damage has occurred during transport either to the packaging or content please contact the delivery com pany responsible Pride Mobility Products Corporation Attn Customer Care Department 182 Susquehanna Avenue Exeter PA 18643 2694 info pridemobility com NOTE If you ever lose or misplace your copy of this manual contact us and we will be glad to send you a new one immediately 4 www pridemobility com Q6 Edge VA 11 SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the power chair to identify warnings mandatory actions and prohibited actions It is very important for you to read and understand them completely NOTE There are more warnings identified and explained in the Consumer Safety Guide that is included with your power chair Please become familiar with all the warnings and safety information found in the Consumer Safety Guide and refer to this resource often Read and follow the information in the owner
27. ir when the drive motors are disengaged To operate the manual freewheel levers 1 Push down both manual freewheel levers for freewheel mode drive motor disengaged See figures 4A and 4B 2 Pull up both manual freewheel levers for drive mode drive motor engaged See figures 5A and 5B NOTE You must turn off the power before disengaging the drive motors otherwise you may get an error code on the controller To clear this code turn off the controller and place the power chair in drive mode Then turn on the controller The error message should be cleared If it is not contact your Quantum Rehab Provider NOTE The power chair will be significantly easier to push with the power off WARNING Avoid applying excessive force to the manual freewheel levers manual freewheel levers Applying excessive force to the manual freewheel levers may result in AN WARNING Do not use your foot to operate the manual freewheel levers Do not stand on the 2 damage to the freewheel levers motors and brakes WARNING Do not use the freewheel lever handles as tie down points to secure this product EN De lt DA MA U A m 224 74 Figure 4 Freewheel Mode Right Drive Motor Disengaged Disengaged 10 www pridemobility com Q6 Edge VA lll YOUR POWER CHAIR 2 E LD 7 er MANUAL FREEWHEEL LEVER Figure 5A Drive Mode Left Drive Motor Engaged Figure 5B Drive Mode Right Dri
28. ket See figure 16 3 Slide the controller into or out of the armrest to the desired position 4 Tighten the setscrew to secure the controller To change the controller position 1 Turn off the power to the controller 2 Unplug the controller connector s from the power base Remove any wire ties securing the controller har ness to the armrest Flip up the armrest so it is perpendicular to the floor Loosen the setscrew on the controller bracket Slide the controller out of the armrest Loosen the setscrew in the other armrest Place the controller in the other armrest Tighten the setscrews in both armrests 0 Route the controller harness to the back of the power base and plug in the controller 11 Secure the controller harness to the armrest with wire ties See figure 10 p Figure 16 Underside of Armrest eo SON Mig NOTE If your power chair is equipped with a Spe cialty Seat Synergy Seat or TRU Balance Power Positioning System refer to the information provided in supplemental manuals provided with your seating system Q6 Edge VA www pridemobility com 19 V COMFORT ADJUSTMENTS Foot Platform Height Adjustment The foot platform height is easily adjusted to several different heights To raise or lower the foot platform 1 Remove the hardware from the foot platform bracket See figure 17 2 Raise or lower the foot platform to the desired height 3 Reinstall the hardware into the foot plat
29. l surface only Never raise the seat from its lowest position on an inclined surface Failure to heed this warning can result in the power chair tipping over Figure 18 Power Elevating Seat Toggle Switch WARNING Never raise the seat from its lowest position when operating your power chair on bumpy or uneven surfaces Failure to heed this warning can result in the power chair tipping over WARNING Never raise the power elevating seat while your power chair is in the freewheel mode WARNING Always fasten the positioning belt when operating the power elevating seat NOTE The power elevating seat option is equipped with a system that reduces the speed of the power chair to one quarter when the seat is elevated Always check to be sure this system is operating properly before using your power chair Q6 Edge VA www pridemobility com 21 V COMFORT ADJUSTMENTS Positioning Belt Your power chair may be equipped with a positioning belt that can be adjusted for operator comfort See fig ure 19 The positioning belt is designed to support the operator so that he she does not slide down or forward in the seat The positioning belt is not designed for use as a restraining device WARNING The positioning belt is not designed for use as a seat belt in a motor vehicle Nor is your power chair suitable for use as a seat in any vehicle Anyone traveling in a vehicle TAN should be properly belted into seats 2 approved by
30. l of your power chair 2 After one second check the battery condition meter Make sure that it remains on 3 Slowly push the joystick forward until you hear the electric brakes click Immediately release the joystick You must be able to hear each electrical brake operating within a few seconds of joystick movement Repeat this test three times pushing the joystick backwards then left and then right Monthly Checks Check for drive tire wear See your Quantum Rehab Provider for repair Check the caster wheels for wear Replace them as necessary Check the caster forks for damage or fluttering which indicates that they may need to be adjusted the bearings replaced See your Quantum Rehab Provider for repair Check the entire power chair for loose hardware and changes in the function or performance of the power chair See your Quantum Rehab Provider for service or repair Keep your power chair clean and free of foreign material such as mud dirt hair food drink etc Spring shocks and gas dampers should be visually checked for any abnormality structure damage or bent rods See your Quantum Rehab Provider for repair Yearly Checks Take your power chair to your Quantum Rehab Provider for yearly maintenance especially if you use your power chair on a daily basis This helps ensure that your power chair is functioning properly and helps prevent future complications 28 www pridemobility com Q6 Edge VA
31. most efficient tool to charge the batteries We do not recommend using other types of chargers e g an automotive battery charger NOTE Your power chair s charger will not operate after the batteries have been discharged to nearly zero voltage Ifthis happens call your Quantum Rehab Provider for assistance How often must I charge the batteries Many factors come into play when deciding how often to charge the batteries You may use your power chair all day on a daily basis or you may not use it for weeks at a time 24 www pridemobility com Q6 Edge VA VI BATTERIES AND CHARGING Daily Use If you use your power chair on a daily basis charge the batteries as soon as you are finished using your power chair Your power chair will be ready each morning to give you a full day s service It is recommended that you charge the batteries at least 8 to 14 hours after daily use Pride recommends that you charge the batteries for an additional 4 hours after the battery charger indicates that charging is complete E Infrequent Use If you use your power chair infrequently once a week or less you should charge the batteries at least once per week for at least 24 hours NOTE Keep your batteries fully charged and avoid deeply discharging your batteries Refer to the manual supplied with the battery charger for charging instructions Pride recommends charging your batteries for at least 48 continuous hours once per month to improve battery per
32. n on the power Check the harness connections Make sure they are tight Check the circuit breaker Reset it if necessary Check the battery connections If the above conditions prove normal you can load test the batteries with a battery load tester These testers are available at automotive parts stores Disconnect both batteries before load testing and follow the directions that come with the load tester If either one of the batteries fails the load test replace both of them If your power chair still does not power up contact your Quantum Rehab Provider 32 www pridemobility com Q6 Edge VA Q6 Edge www pridemobility com 33 34 www pridemobility com Q6 Edge VA Q6 Edge U 4 4 09 Product Serial
33. ooling slots then do not attempt to insert objects through these slots u WARNING If your battery charger has not been tested and approved for outdoor Y IN use then do not expose it to adverse or extreme weather conditions If the battery fa charger is exposed to adverse or extreme weather conditions then it must be N allowed to adjust to the difference in environmental conditions before use indoors Refer to the manual supplied with the battery charger for more information Q6 Edge VA www pridemobility com 23 VI BATTERIES AND CHARGING To charge the batteries using the off board charger 1 Position your power chair next to a standard electrical outlet 2 Be certain the controller power is turned off and the power chair is in drive mode 3 Plug the off board charger into the off board charger programming socket on the controller See figure 20 4 Plug the off board charger into the electrical outlet WARNING The LED lights on the charger indicate different charger conditions at various times charger power on charging in progress and charging complete If the y N LED does not indicate that charging is 2 complete within 24 hours unplug the 4 2 charger from the outlet and contact your Quantum Rehab Provider Refer to the manual supplied with the charger for a complete explanation of these indicators Figure 20 Battery Charging 5 When the batteries are fully charged unplug the off board ch
34. ored without a full charge may be permanently damaged causing unreliable power chair operation and limited battery life NOTE The useful life of a battery is quite often a reflection of the care it receives How should I store my power chair and its batteries If you do not use your power chair regularly we recommend maintaining battery vitality by charging the batteries at least once per week If you do not plan on using your power chair for an extended period fully charge the batteries prior to storage Disconnect the battery harnesses and store the power chair in a warm dry environment Avoid temperature extremes such as freezing and excessively hot conditions and never attempt to charge a frozen battery A cold or frozen battery should be warmed for several days prior to recharging What about public transportation AGM and Gel Cell batteries are designed for application in power chairs and other mobility vehicles These batteries are Federal Aviation Administration FAA approved allowing safe transportation on aircraft buses and trains as there is no danger of spillage or leakage We suggest you contact the carrier s ticket counter in advance to determine that carrier s specific requirements What about shipping If you wish to use a freight company to ship your power chair to your final destination repack your power chair in the original shipping container and ship the batteries in separate boxes 26 www pridemobility com
35. power base 5 Remove both extrusions from the bottom of the seat 6 Reposition the extrusions on a different set of mounting holes You must move both extrusions the same number of holes either forward or back wards See figure 14 7 Fasten the extrusions back onto the bottom of the seat 8 Reinstall the seat 9 Reconnect the controller to the power base SEAT MOUNTING HOLES Figure 14 Seat Position Adjustment Manual Recline Seatback Adjustment If your power chair is equipped with a reclining seat you can adjust the seatback angle with the seatback release lever The lever is located on the right side of the seat base To adjust the recline angle 1 Pull up on the seatback release lever 2 Lean forward or backwards to the desired position 3 Release the lever Q6 Edge VA www pridemobility com 17 V COMFORT ADJUSTMENTS Seatback Angle Adjustment If your power chair is equipped with an adjustable seat back you can adjust it to four 4 different angles 90 102 105 or 107 To adjust the seatback angle 1 Remove the adjusting screws from each seat hinge See figure 15 2 Set the seatback at the desired angle 3 Reinstall the adjusting screws to each seat hinge and tighten Armrest Width Adjustment You can change each armrest s width independently of the other NOTE Changing the armrest width may increase the overall width of your power chair To change the armrest width 1
36. pped with a Specialty Seat Synergy Seat or TRU Balance Power Position ing System refer to the seat adjustment information contained in separate manuals If your power chair is equipped with a contoured seating system refer to the following information WARNING The center of gravity of your power chair was factory set to a position that meets the needs of the demographic majority of users Your Quantum Rehab Provider has evaluated your power chair and made any necessary adjustments to suit your specific requirements Do not change your seating configuration without first contacting Pride Mobility Products or your AN Quantum Rehab Provider IS WARNING Some power chair components heavy You need assistance to lift or carry them Please refer to the specifications table for specific component weights before you disassemble the power chair G WARNING Remove the occupant from the power chair before making any adjustments You may need the following to make comfort adjustments metric standard socket set and ratchet TRAPEZE BARS adjustable wrench metric standard hex key set thread lock Seat Height and Seat Angle Adjustment If your power chair is not equipped with a transit securement system you can change the seat height to one of three positions by raising the front and rear tra peze bars If you raise or lower only one trapeze bar front or rear you can also change the seat base angle dump
37. rasive cleanser to clean the plastic and metal parts of your power chair Avoid using products that may scratch the surface of your power chair If necessary clean your product with an approved disinfectant Make sure the disinfectant is safe for use on your product before application WARNING Follow all safety instructions for the proper use of the disinfectant and or cleaning agent before applying it to your product Failure to comply may result in skin irritation or premature deterioration of upholstery and or power chair finishes IN WARNING Never hose off your power chair or place it in direct contact with water Your power 4 Chair has a painted ABS plastic body shroud that allows it to be easily wiped clean with a damp i cloth WARNING Never use any chemicals to clean a vinyl seat as they may cause the seat to become slippery or dry out and crack Use soapy water and dry the seat thoroughly Wheel Replacement If you have pneumatic tires and you have a flat tire you can replace the tube If your chair is equipped with a solid tire insert then you must replace the entire wheel assembly Replacement tires tubes and wheel assemblies are readily available through your Quantum Rehab Provider WARNING The wheels on your power chair should only be serviced or replaced by a Quantum Rehab Provider or a qualified technician WARNING sure that the controller s power is turned off and the power chair is not in 2
38. s manual Locked and in drive mode Place unit on level ground and stand to one side when changing from drive mode to freewheel mode or freewheel mode to drive mode Unlocked and in freewheel mode Indicates power chair securement points Indicates that power chair with similarly labeled seating system conforms to ANSI RESNA WC Vol 4 Section 19 for transport of an occupied power chair in a motor vehicle Indicates that power chair with a similar label is not rated for occupied transit Class Equipment p Manufactured XXXXXXX QUANTUM www pridemobility com Power chair information label Q6 Edge VA www pridemobility com 9 11 SAFETY GENERAL GUIDELINES Ve MANDATORY Do not operate your new power chair for the first time without completely reading and understanding this owner s manual I Your power chair is a state of the art life enhancement device designed to increase mobility Pride provides an extensive variety of products to best fit the individual needs ofthe power chair user Please be aware that the final selection and purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user who is capable of making such a decision and his her healthcare professional i e medical doctor physical therapist etc The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair to th
39. side of the armrest pad Route the harness 7 N under the armrest or toward the inside of the armrest pad Use correct tie N A down points for controller harness to prevent the harness from getting caught in the drive tires pinched in the seat frame or damaged when passing through doorways 5 Plug the controller connector into the rear of the power base See figure 3 6 Secure the controller harness to the armrest receiver with wire ties See figure 10 HARDWARE To install the seat Transit Securement System 1 Attach the seat plate to the four mounting brackets on the power base and ensure all hardware is prop i erly installed and tightened securely See figure 9 NZ MOUNTING 2 Install the controller and route the harness to the A BRACKETS back of the power See figure 10 HARDWARE MANDATORY Prevent controller harness damage Avoid routing the controller harness on the outside of the armrest pad Route the harness ge under the armrest or toward the inside of the armrest pad Use correct tie A y down points for controller harness to prevent the harness from getting caught in the drive tires pinched in the seat frame or damaged when passing through doorways gt B gt a TO POWER BASE R Figure 10 Controller Harness Routing on a Contour Seat 14 www pridemobility com Q6 Edge VA IV ASSEMBLY Power Elevating Seat Option Your power chair may be
40. tion that have the capability of operating a powered wheelchair Quick Reference Information Quantum Rehab Provider Address Phone Number Purchase Date NOTE This owner s manual is compiled from the latest specifications and product information available at the time of publication We reserve the right to make changes as they become necessary Any changes to our products may cause slight variations between the illustrations and explanations in this manual and the product you have purchased The latest current version of this manual is available on our website NOTE This product is compliant with WEEE RoHS and REACH directives and requirements NOTE This product meets IPX4 classification IEC 60529 NOTE The Q6 Edge VA and its components are not made with natural rubber latex Consult with the manufacturer regarding any after market accessories Copyright 2013 Pride Mobility Products Corp INFMANU4409 Rev B September 2013 CONTENTS E INTRODUCTION er 4 Il SAFETY ee era near 5 IL YOUR POWER CHAIR u a en 7 IV ASSEMBLY 0000 a A AA 12 V COMFORT ADJUSTMENTS 16 VI BATTERIES AND CHARGING 23 VII CARE AND MAINTENANCE 27 EA ss zrx ETGTI Yw _ _he r P P c c _ Q6 Edg
41. ve Motor Engaged AT nz ww N Q6 Edge www pridemobility com 11 IV ASSEMBLY INITIAL ASSEMBLY Your power chair may require some assembly either before initial use or after transportation It may also require disassembly to make some comfort adjustments Figure 6 details those parts of the power chair that are designed to be disassembled and assembled by an end user or by a qualified caregiver before using the product or making comfort adjustments NOTE Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be replaced with a new nut Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert resulting in a less secure fit Replacement nylon insert lock nuts are available at local hardware stores or through your Quantum Rehab Provider ARMREST ANGLE ADJUSTMENT CONTROLLER POSITION SEAT HEIGHT ANGLE ADJUSTMENT FOOT PLATFORM ANGLE ADJUSTMENT FOOT PLATFORM HEIGHT DEPTH ADJUSTMENT Figure 6 Q6 Edge VA Assembly View Synergy Seat Shown 12 www pridemobility com Q6 Edge VA IV ASSEMBLY Seat Installation It may be necessary to install the seat either prior to initial operation or after transporting your power chair For unoccupied transit power chairs contour seats are attached to the power base with the Universal Mount ing System UMS The UMS consists of universal parts that may be attached to the seat regardless of seat wi
Download Pdf Manuals
Related Search