Q-Logic 5800V SERIES Switch User Manual
Contents
1. 2 SWITCH STACK 5 SWITCH STACK uem gmmg Burger i Tal ET ea H 1 z TT ESL ILL Spm slept Fees Pees eo ERANT Bay Oke FE Be ey Tee TERMIN I A T MR 3 SWITCH STACK BEBE SEHE mm mem Tipit e mmm Sri EE ten 4 SWITCH STACK Step 4 Install Transceivers An SFP transceiver is required for each SFP port that will be connected to a device or another switch The SFP ports support 2 Gbps 4 Gbps and 8 Gbps transmission The XPAK ports support 10 Gbps transmission and can be upgraded to 20 Gbps with a license key The standard switch model activates SFP ports 0 7 plus the XPAK ports 20 23 You can activate ports 8 19 in four port increments with the purchase of a Port Activation license key Contact your authorized reseller for information about license keys NOTE If your SANbox 5802V switch came with 20 SFPs and a 3 inch stacking cable ports 0 23 are active L To install an SFP transceiver insert the transceiver into the switch port and gently press until it snaps in place The transceiver will fit only one way If the tran2. FIBRE CHANNEL SWITCH INSTALLATION XX oLocic Please feel free to contact your QLogic approved reseller or QLogic Technical Support at any phase of integration for assistance QLogic Technical Support can be reached by the following methods Web http support glogic com E mail support qlogic com The QLogic knowledge database contains troubleshooting information for the QLogic HBAs Access the data base from the QLogic Support Web page http support glogic com Use the Support Center search engine to look for specific troubleshooting information Quick Start Guide Installation Instructions Congratulations on your purchase of the SANbox 5800V Series Stackable Fibre Channel Switch This guide describes the steps to install and activate your new switch using a Windows workstation For advanced options and instructions including Solaris Linux and Mac OS X installations refer to the SANbox 5800V Series Stackable Fibre Channel Switch Installation Guide which is available at www qlogic com NOTE Do not apply power to the switch until instructed in Step 5 Step 1 Verify the Package Contents The SANbox 5800V Series Fibre Channel Switch is shipped with the following items SANbox 5800V Series Stackable Fibre Channel Switch AC Power cord 5800V AC Power cords 5802V Rubber feet Enterprise Fabric Suite 2007 CD free 30 day trial _ h L2 Depending on which SANbox 5800V switch you ordered it may also inc
3. log in to and manage the switch using the command line interface or the QuickTools web applet This guide will describe the use of QuickTools C Open an Internet browser and enter the default IP address 10 0 0 1 to start the QuickTools web applet L Login to the switch using the default user name admin and password password Step 9 Run the Configuration Wizard C Obtain the IP address and subnet mask from your network administrator C Open the QuickTools Wizards menu and select Configuration Wizard Follow the instructions to set network parameters and the password The default user name is admin the default password is password Changing the IP address will terminate the QuickTools session C Open an Internet browser and start a new QuickTools session Enter the new IP address to log in to switch Step 10 Connect Devices L1 Connect fiber optic cables between the installed transceivers and their corresponding devices Each port auto negotiates the proper port type with the connected device Congratulations You have successfully installed your QLogic SANbox 5800V Series Switch 2009 QLogic Corporation QLogic the QLogic logo SANbox and Enterprise Fabric Suite 2007 are trademarks or registered trademarks of QLogic Corporation Microsoft Windows and Internet Explorer are registered trademarks of the Microsoft Corporation MacOS X is a registered trademark of Apple Computer Inc Linux is a registered trademark of Lin
4. lude Small Form factor Pluggable SFP transceivers and or XPAK switch stacking cables XPAK switch stacking cables connect SANbox 5800V Series switches together through the XPAK ports NOTE fyou ordered SFPs and XPAK switch stacking cables separately they will arrive in a different package XPAK switch stacking cables connect SANbox 5800V Series switches together through the XPAK ports Step 2 Mount the Switch Q Fora surface mount attach the rubber feet to the locations on the bottom of the switch For a rack mount install the SANbox 3000 5000 series rail kit and the switch in a standard 19 rack as described in the SANbox 3000 5000 Series Fibre Channel Switch Rack Mounting Guide Step 3 Stack Switches You can connect up to six switches together through the XPAK ports using XPAK switch stacking cables Stacking provides performance and fail over while preserving ports for devices a a a a a For a 2 switch stack use two 3 inch stacking cables For a 3 switch stack use two 3 inch stacking cables and one 9 inch stacking cable For a 4 switch stack use three 3 inch stacking cables and three 9 inch stacking cables For a 5 switch stack use four 3 inch stacking cables and four 9 inch stacking cables For a 6 switch stack use two 3 inch stacking cables and six 9 inch stacking cables Q Remove the XPAK port covers according to the instructions provided with the stacking cables Connect 2 3 4 5 or 6 switches into stacks
5. sceiver does not install under gentle pressure flip it over and try again Step 5 Apply Power to the Switch C Attach the AC power cord s to the switch and wall outlet or power strip For greater availability connect the power cords to separate power circuits Verify that the Input Power LED is illuminated L The switch runs its self tests and begins normal operation this may take a few minutes Verify that the Heartbeat LED is blinking once per second and the System Fault LED is NOT illuminated Step 6 Verify Workstation Requirements QO Verify that your workstation can support the QuickTools application with the following minimum requirements L Windows 2003 and XP SP1 SP2 512 MB memory minimum 1 GB recommended 1 GHz processor Video card with 256 colors RJ 45 Ethernet port Internet Browser Microsoft Internet Explorer 6 0 and later Netscape Navigator 6 0 and later Firefox 1 5 and later or Mozilla 1 5 Q The default IP address of a new switch is 10 0 0 1 Ensure that your workstation is configured to communicate with the 10 0 0 subnet Ooooo Step 7 Connect the Workstation to the Switch L1 Connect the workstation to the switch using an Ethernet cable the switch automatically recognizes both straight and cross over Ethernet cables If you are using a Windows workstation you must have a live Ethernet connection when the workstation powers up Step 8 Log In to the Switch You can
6. us Torvalds Mozilla and Firefox are trademarks or registered trademarks of the Mozilla Foundation Netscape Navigator is a registered trademarks of Netscape Communications Corporation Java and Solaris are registered trademarks of Sun Microsystems Inc All other brands and product names are trademarks or registered trademarks of their respective owners Information supplied by QLogic is believed to be accurate and reliable QLogic Corporation assumes no responsibility for any errors in this brochure QLogic Corporation reserves the right without notice to makes changes in product design or specifications XKX QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo CA 92656 949 389 6000 www qlogic com QLOGIC 50861 02 B The Ultimate in Performance
Download Pdf Manuals
Related Search