Promise Technology SATA 300 Computer Hardware User Manual
Contents
1. S to use the driver on the floppy disk and then press Enter to continue with installation The Windows Server 2003 Setup screen will appear again saying Setup will load support for the following mass storage devices The list will include Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE Controller NOTE If there are any additional devices to be installed specify them now When all devices are specified continue to the next step From the Windows Server 2003 Setup screen press the Enter Setup will now load all device files and then continue the Windows Server 2003 installation Existing Installation After installing the STAII150 or SATA300 Serial ATA Controller card and rebooting your system Windows Server 2003 setup will show a Found New Hardware dialog box Under Windows 2003 Mass Storage Controller will be displayed 1 Insert the driver diskette into the A drive 10 Step 4 Install Drivers Choose nstall the software automatically and press the Enter key Choose Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE Controller from the list that appears on screen and then press the Enter key If using a driver that has not been digitally signed by Microsoft you will be asked if you want to continue the installation Click Continue anyway When the New Hardware Wizard has finished installing the SATAII150 or SATA300 driver click Finish Confirm Installation f2. diskettes e CD ROM Install Boot from the CD ROM Press F6 after the message Press F6 if you need to install third party SCSI or RAID driver appears When the Windows 2000 Setup window is generated press S to specify an Additional Device s Insert the driver diskette into drive A and press Enter Choose Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE Controller from the list that appears on screen then press Enter 12 Step 4 Install Drivers The Windows 2000 Setup screen will appear again saying Setup will load support for the following mass storage devices The list will include Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE Controller NOTE If there are any additional devices to be installed specify them now When all devices are specified continue to the next step From the Windows 2000 Setup screen press Enter Setup will now load all device files and then continue the Windows 2000 installation Existing Installation After installing the SATAII150 or SATA300 Serial ATA Controller card and rebooting your system Windows 2000 setup will show a New Hardware Found dialog box Under Windows 2000 PCI Mass Storage Controller will be displayed 1 Choose Add New Hardware Wizard from the list and then press Enter 2 Choose Add Troubleshoot a device and click Next The new hardware 10 11 12 wizard will show device list The screen show a Welcome to
3. the Found New Hardware Wizard dialog box Click Next Choose Display a list the known drivers for this device so that can choose a specific driver then click Next Select SCSI and RAID controllers then click Next When the Windows 2000 supported SCSI adapter drivers list appears click Have disk Insert the driver diskette in drive A Type A in the text box then click OK Choose Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE controller from the list that appears on screen then click Next If using a driver that has not been digitally signed by Microsoft you will be asked if you want to continue the installation Click Yes Click Yes to confirm continue the installation and copy the driver to system Remove the diskete and click Finish to restart the system Windows 2000 will then restart for the driver installation to take effect 13 SATAII150 and SATA300 TX Series Quick Start Guide Confirm Installation 13 Right click on the My Computer icon and select Manage from the popup menu From the left panel select Device Manager Click the in front of SCSI controllers Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE Controller should appear RedHat Linux Prepare a driver diskette f 3 Download the RedHat Linux driver from the Promise website at www promise com Extract the contents of the ZIP file on to a formatted floppy disk Use WinZIP in Windows or u
4. PROMISE SATAIITSO AND SATA 300 TA SERIES Quien START GUIDE SATAII150 and SATA300 TX Series Quick Start Guide SATAII150 TX Series Task List Installation and setup consists of the following steps 1 Unpack Your SATAII150 or SATA300 Card below 2 Install the SATAII150 or SATA300 Card page 3 3 Install the Disk Drives SATAII150 TX2plus or SATA300 TX2plus page 4 SATAII150 TX4 page 5 SATA300 TX4 page 7 4 Install Driver page 9 Step 1 Unpack Your SATAII150 or SATA300 Card When you receive the SATAII150 or SATA300 TX2plus card the package should contain the items listed below SATAII150 or SATA300 TX2plus Serial ATA Controller card e Quick Start Guide e Two 0 65 m 26 inch Serial ATA data cables 1 5 Gb cables for SATAII150 3 0 Gb cables for SATA300 e One 80 wire 40 pin ATA cable e CD with drivers and SATAII150 and SATA300 TX Series User Manual When you receive the SATAII150 or SATA300 TX4 card the package should contain the items listed below SATAII150 or SATA300 TX4 Serial ATA Controller card e Quick Start Guide e Four 0 65 m 26 inch Serial ATA data cables 1 5 Gb cables for SATAII150 3 0 Gb cables for SATA300 e CD with drivers and SATAII150 and SATA300 TX Series Manual If ANY of the contents are missing or appear to be damaged please contact your dealer or distributor immediately Warning Before installing the adapter into an existing system backup any important or useful data Failur
5. Right click on the My Computer icon and select Manage from the popup menu 2 From the left panel select Device Manager 3 Click the in front of SCSI and RAID controllers Windows Promise SATAII150 SATA300T X2plus or TX4 tm IDE Controller should appear Windows XP New Installation The following details the installation of the SATAII150 or SATA300 Serial ATA Controller drivers while installing Windows XP di Start the installation e Floppy Install Boot the computer with the Windows XP installation diskettes e CD ROM Install Boot from the CD ROM Press F6 after the message Press F6 if you need to install third party SCSI or RAID driver appears When the Windows XP Setup window is generated press S to specify an Additional Device s Insert the driver diskette into drive A and press Enter Choose Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE Controller from the list that appears on screen and then press the Enter Press S to use the driver on the floppy disk and then press Enter to continue with installation The Windows XP Setup screen will appear again saying Setup will load support for the following mass storage devices The list will include Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE Controller NOTE If there are any additional devices to be installed specify them now When all devices are specified continue to the next step 11 SATAII150 an
6. Then attach the other ends of the cables to the connectors on the SATA300 TX4 card below Port 1 Channel 1 Individual LED Aggregate LED Connectors Connectors Port 2 Channel 2 Management Connector SEE ONL LOD Z Port 3 Channel 3 SATA300 TX4 SATA 300 ONY TOKIO Port 4 Sl 1 Channel 4 SATA300 TX4 Serial ATA Controller card Step 4 Install Drivers Step 4 Install Drivers Make a Driver Installation Diskette Windows below Windows Server 2003 New page 10 e Exsting page 10 e Confirm page 11 Windows XP e New page 11 e Exsting page 12 e Confirm page 12 Windows 2000 e New page 12 e Exsting page 13 e Confirm page 14 RedHat Linux e New page 14 e Exsting page 15 SuSE Linux e New page 15 e Exsting page 16 Following are driver installation procedures for the Windows operating systems that support the SATAII150 and SATA300 TX Series Serial ATA Controller cards The drivers for Windows are included on the CD Drivers and installation instructions for Linux operating systems are downloadable from the Promise website at www promise com Make an Installation Floppy Diskette Windows This procedure requires one write enabled blank 3 5 inch diskette 4 5 P
7. d SATA300 TX Series Quick Start Guide 7 From the Windows XP Setup screen press the Enter Setup will now load all device files and then continue the Windows XP installation Existing Installation After installing the SATAII150 or SATA300 Serial ATA Controller card and rebooting your system Windows XP setup will show a Found New Hardware dialog box 1 2 3 Insert the driver diskette into the A drive Choose Install the software automatically and press the Enter key Choose Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE Controller from the list that appears on screen and then press the Enter key If using a driver that has not been digitally signed by Microsoft you will be asked if you want to continue the installation Click Continue anyway When the New Hardware Wizard has finished installing the SATAII150 or SATA300 driver click Finish Confirm Installation LE Right click on the My Computer icon and select Manage from the popup menu 2 From the left panel select Device Manager 3 Click the in front of SCSI and RAID controllers Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE Controller should appear Windows 2000 New Installation The following details the installation of the SATAII150 or SATA300 Serial ATA Controller drivers while installing Windows 2000 il Start the installation e Floppy Install Boot the computer with the Windows 2000 installation
8. e to follow this accepted PC practice could result in data loss Step 2 Install the SATAII150 or SATA300Card Warning The SATAII150 or SATA300 TX Series Serial ATA Controller cards like other parts of your system are subject to damage by A static electricity Be sure that you re properly grounded Promise recommends that you wear an anti static strap or touch a grounded object and that you unplug your system before installing the SATAII150 or SATA300 TX2plus and TX4 Step 2 Install the SATAII150 or SATA300Card The SATAII150 or SATA300 TX2plus or TX4 Serial ATA Controller card fits into any available PCI slot on your PC s motherboard below e 32 bit PCI slot must be PCI 2 2 or 2 3 compliant e The 32 bit portion of a 64 bit PCI or PCI X slot Attaching screw System frame Bracket SATAII150 or SATA300 Controller card Motherboard PCI slots e Remove the cover of your system SATAII150 and SATA300 TX Series Quick Start Guide Remove the inside slot cover of an available 32 bit PCI slot on the motherboard Install the SATAII150 or SATA300 card into the open PCI slot Secure the bracket to the system s frame Attach your system case s 2 or 4 pin LED cable to the LED connector on the SATAII150 or SATA300 card see nstall the Disk Drives below Make sure that pin 1 on the connector is aligned with pin 1 of t
9. following commands mount dev fd0 floppy cd floppy sh install Note At the prompt answer Yes to load SATAII 150 driver every time Linux boots cd umount floppy 16
10. he cable Fasten the controller card bracket to the system case Note The SATAII150 or SATA300 TX2plus and TX4 Controllers are PCI Plug n Play PnP devices No changes are necessary in the Motherboard CMOS Setup for resources or drive types in most applications Step 3 Install the Disk Drives SATAII150 or SATA300 TX2plus The SATAII150 or SATA300 TX2plus supports up to two Serial ATA drives and up to two Parallel ATA drives 1 2 Caution Use of removable disk drive enclosures other than Promise Technology s SuperSwap is not supported and may result in performance loss or other undesired results Note If you are using a Promise SuperSwap 1100 or 4100 enclosure in your PC e Connect the power cables to the SuperSwap enclosure Attach a SMBus cable from the Management Connector on the SATAII150 or SATA300 TX2plus card to the Management Connector on the first enclosure These actions are described in Chapter 2 of the SuperSwap User Manual Install the disk drives into the drive bays of your system Attach the power cables to the disk drives Step 3 Install the Disk Drives Attach one Serial ATA data cable to each Serial ATA disk drive Then attach the other ends of the cables to the connectors on the SATAII150 or SATA300 TX2 plus card below Individual LED Connectors Parallel Port Port 3 Ch 13 Aggregate LED bi anne Connector
11. lace your blank diskette in the appropriate drive Insert the Promise CD into your CD ROM drive The display screen should open automatically If the display screen does not open click on MyComputer gt CD Drive D and double click on the Launch exe icon Click on the Windows Driver button The Disk Copy Utility opens SATAII150 and SATA300 TX Series Quick Start Guide 9 10 Click the Create button in the Utility A confirmation box appears Click the Yes button in the confirmation box The utility prepares your driver installation diskette When the utility is finished it displays a message In the message click the OK button Click the Exit button to close the Promise CD Windows Server 2003 New Installation The following details the installation of the SATAII150 or SATA300 Serial ATA Controller drivers while installing Windows Server 2003 i Start the installation Floppy Install Boot the computer with the Windows Server 2003 installation diskettes e CD ROM Install Boot from the CD ROM Press F6 after the message Press F6 if you need to install third party SCSI or RAID driver appears When the Windows Server 2003 Setup window is generated press S to specify an Additional Device s Insert the driver diskette into drive A and press Enter Choose Windows Promise SATAII150 SATA300TX2plus or TX4 tm IDE Controller from the list that appears on screen and then press the Enter Press
12. nzip in Linux Label the disk SATAII 150 Driver Disk New Installation 1 Boot the Linux system from the Red Hat Linux Installation with CD At the Welcome to Red Hat linux installation screen a prompt labeled boot will appear at the bottom of the screen At the boot prompt type expert and press the Enter key See the Note below At the Devices dialog box insert the SATAII 150 Driver Disk in the floppy drive and then select OK or Yes Continue with the installation as normal When installation is at the Congratulations menu press Ctrl Alt F2 to switch screens Insert the SATAII 150 Driver Disk into the floppy drive Type the following commands to load SATAII 150 driver umount tmp fdO if this command fails ignore it and go to the next one chroot mnt sysimage mount dev fd0 mnt cd mnt sh setup ut cd umount mnt exit Please Press Ctrl Alt F7 and click the Exit button to finish the installation 14 Step 4 Install Drivers NOTE Red Hat Linux will not provide onboard IDE as standard ide0 and ide1 on some mother boards To solve this condition append the boot parameters as follows ide0 0x1f0 0x3f6 14 ide1 0x170 0x376 15 ide2 0 ide3 0 ide4 0 ide5 0 ide6 0 ide7 0 ide8 0 ide9 0 Existing Installation 1 2 3 Boot the Linux system and log in as root Insert SATAII 150 Driver Disk In a terminal window enter the following commands mount de
13. s UIL Port 2 0000 OOOO PROMISE Channel 2 ji DNOO0ODO pL Port 1 an T Channel 1 E E E SATAISO SATAN50 i U DOVOIITTTTTTTTTTTKKKKKKKKK ll Management Connector SATAII150 or SATA300 TX2plus Serial ATA Controller card Attach a black connector of the Ultra ATA cable to each Parallel ATA hard drive Verify that the Master and Slave drives each have the appropriate pin settings Check the drive manufacturer s documentation for more information Attach the blue cable connector to the Port 3 Parallel connector on the SATAII150 or SATA300 TX2plus controller card The colored edge of the cable s indicates pin 1 SATAII150 TX4 The SATAII150 TX4 supports up to four Serial ATA drives Caution Use of removable disk drive enclosures other than Promise Technology s SuperSwap is not supported and may result in performance loss or other undesired results SATAII150 and SATA300 TX Series Quick Start Guide Note If you are using a Promise SuperSwap 1100 or 4100 enclosure in your PC e Connect the power cables to the SuperSwap enclosure Attach a SMBus cable from the Management Connector on the SATAII150 TX4 card to the Management Connector on the first enclosure These actions are described in Chapter 2 of the SuperSwap User Manual Install the disk drives into the drive bays of your system 2 Attach the power cables to the disk drives 3 Attach one Serial ATA data cable to each Serial ATA di
14. sk drive Then attach the other ends of the cables to the connectors on the SATAII150 TX4 card below Individual LED Aggregate LED Port 1 Port 3 Connectors Connectors Channel 1 Channel 3 noong Management Connector e OOOOH Oooo LI OOOO moona T TUTTO Port 2 Port 4 Channel 2 Channel 4 SATAIS0 ES ANN NS RSI OY LC TX4 SATA1150 PROMISE To na SATAII150 TX4 Serial ATA Controller card Step 3 Install the Disk Drives SATA300 TX4 The SATA300 TX4 supports up to four Serial ATA drives Caution Use of removable disk drive enclosures other than Promise Technology s SuperSwap is not supported and may result in performance loss or other undesired results Note If you are using a Promise SuperSwap 1100 or 4100 enclosure in your PC Connect the power cables to the SuperSwap enclosure Attach a SMBus cable from the Management Connector on the SATA300 TX4 card to the Management Connector on the first enclosure These actions are described in Chapter 2 of the SuperSwap User Manual 1 Install the disk drives into the drive bays of your system 2 Attach the power cables to the disk drives SATAII150 and SATA300 TX Series Quick Start Guide 3 Attach one Serial ATA data cable to each Serial ATA disk drive
15. v fd0 mnt floppy cd mnt floppy sh install Note At the prompt answer Yes to load SATAII 150 driver every time Linux boots cd umount dev fd0 SuSE Linux Prepare a driver diskette f 3 Download the RedHat Linux driver from the Promise website at www promise com Extract the contents of the ZIP file on to a formatted floppy disk Use WinZIP in Windows or unzip in Linux Label the disk SATAII 150 Driver Disk New Installation 1 2 Boot the Linux system from the SuSE Linux Installation with CD When system boots press F3 for Driver Disk and select the Installation option See the Note below When Please insert the Driver Update floppy displays insert the SATAII 150 Driver Disk into the floppy drive When Driver Update Menu appears select OK then select back to return to the installer Continue with the installation as normal If you are using SMP system add a parameter acpi off to kernel boot parameters in the Booting menu of Installation Settings 15 SATAII150 and SATA300 TX Series Quick Start Guide NOTE There is a SMP issue on the SuSE Linux SMP kernel If you encounter problems on SuSE with SMP system append acpi off parameters into boot loader or select Installation ACPI Disabled on SuSE Linux SMP Existing Installation 1 Bootthe Linux system and log in as root 2 Insert SATAII 150 Driver Disk 3 Ina terminal window enter the
Download Pdf Manuals
Related Search