Precor TRM 800 Treadmill User Manual
Contents
1. Do not operate the equipment where aerosol spray products are being used or where oxygen is being administered e Do not use outdoors Do not attempt to service the equipment yourself except to follow the maintenance instructions in this manual e Never drop or insert objects into any opening Keep hands away from moving parts e Do not set anything on the stationary handrails handlebars control console or covers Place liquids magazines and books in the appropriate receptacles e Do not lean on or pull on the console at any time AA CAUTION DO NOT remove the cover or you may risk injury due to electric shock Read the assembly and maintenance guide before operating There are no user serviceable parts inside Contact Customer Support if the equipment needs servicing For use with single phase AC supply only Safety Code The club owner or manager has the option to enable the safety code With the code enabled a user must enter four number keys in the correct order before using the equipment If the user does not press the correct keys within two minutes he or she is denied access to the equipment Assembling and Maintaining TRM 800 Series Treadmills Educating Users Take time to educate users about the Important Safety Instructions found in both the User Reference Manual and Product Owner s Manual Explain to your club or facility patrons that they should observe the following precautions Hold onto2. 213 Figure 8 Cable connections and mounting points in the treadmill base Table 1 Cable connections and mounting points in the treadmill base Component Appearance Lower connection point Base unit data Flat with silver insulation Q cable Ethernet cable Flat with black insulation 2 Assembling the Treadmill 23 Component Appearance Lower connection point Television cable Round with black insulation Q Console power Dual leads with red and O cable black insulation Auto Stop sensor Round with black insulation O cable Power supply Rectangular black 5 x O 214 x 14 CAUTION Be careful not to cut or pinch any wires during the following step 3 Place the left hand upright support into the base frame side bracket 4 Secure the left hand upright support to the side bracket using four socket head screws four black washers and two locknuts Partially tighten the fasteners Figure 9 Upright support attachment left side 5 Lower the treadmill fairing assembly over the upright supports and align it to them Important In the following step take care not to unseat any of the components in the stop switch 6 Feed the upper end of the cable assembly through the fairing so that its upper end extends through the bottom opening in the center column and out the round opening in the console mounting plate 24 Assembling and Maintaining TRM 800 Series Treadmills 7 Route the cable ass
3. Base frame assembly Left and right upright supports Center fairing with handrails Hardware kit Installation Requirements The location where the treadmill is installed must provide power connections that supply the appropriate voltage a 20A dedicated branch circuit and grounding as specified on the treadmill CAUTION Do not use a non grounded outlet or transformer Do not remove or otherwise bypass the plug with an adapter Electrical damage can occur and void the Precor Limited Warranty if the treadmill is connected to an improper power source Required Tools Ya inch hex wrench 52 inch hex wrench ball end is desirable Ye inch box end wrench Bubble level 2 Phillips screwdriver String or fish tape Wire cutter Assembling the Treadmill 17 Hardware Kit not to scale The hardware kit shipped with this equipment contains the fasteners and other hardware components shown in the following table Before you begin assembly make sure that your hardware kit is complete If not please contact Precor Customer Support Fasteners Quantity Power cord clips 6 ed x Y inch socket head 8 SAe inch x Y inch buttonhead 6 screws zinc finish 5Ae inch x Y inch buttonhead 4 screws black finish Flat head hex drive screws inch 4 x Ya inch 46 inch locknuts with star washers 4 Se inch split lock washers 10 46 inch flat washers zinc finish 6 46 inch flat washers black finish 12 Note Retrieve the cable
4. Effective 1 November 2010 P N 36286 114 NPRECOR Precor Incorporated TRM 800 Series PAG OM 300713 341 rev G 20031 142nd Avenue NE Warranty 36286 114 P O Box 7202 14 February 2011 Woodinville WA USA 98072 4002
5. cccccssesssssscsssscscscssssssssescscsssssessseesesessaessees 47 Monthly Maintenance c cccccscscsssssssescssesesssscscscesssesscsessesescaneseeeesess 47 Adjusting the Running Belt ssssssssssssssssirerssssrrrrensssnrnrreesnsnrrrreessss 48 Checking the Alignment of the Running Belt 49 Storing the Chest Strap ccccscscssscsssssssssesssssesssssessssssessssesnsesssneess 50 Moving the Equipment c csccscsseccessessessesssssesssssessssssessssssneesssneees 50 Long Term Storage seinare kien np a E EKT 51 Treadmill Safety Features ssssusssunssunnnnnnnunnnnunnunnnunnnnnnnnnnnnnnnnnn 53 Entering the Safety Cod 4 seta gai niecieed tenis ceatadnr tans 53 Using the Treadmill Safety Clip ccccscsssecsssecssssesesseseesesneess 54 Turning the Treadmill On and Off c cccesssssssessesseesesseesesseeeeens 55 Weight Liita waa eters ieee each bo nate 55 LOCALOM eissnes veceteevticrad oreo vrenss aeisi iisi aaa i oni 55 Commercial Cardiovascular Equipment Limited Warranty 57 Chapter Assembling the Treadmill Important The instructions in the following procedures are described from the perspective of a person standing directly in front of the equipment that is on the opposite side of the control console from a person using the equipment These descriptions may not match the names of certain parts in the parts list because such parts are named relative to the back of the equipment WARNING You will need assistance to
6. 800 347 4404 http www precor com Important Safety Instructions Read the following precautions thoroughly before you begin assembly and save them afterward for future reference Safety Precautions Always follow basic safety precautions when using this equipment to reduce the chance of injury fire or damage Other sections in this manual provide more details of safety features Be sure to read these sections and observe all safety notices These precautions include the following Read all instructions in this guide before installing and using the equipment and follow any labels on the equipment Make sure all users see a physician for a complete physical examination before they begin any fitness program Il est conseill de subir un examen m dical complet avant d entreprendre tout programme d exercise Si vous avez des tourdissements ou des faiblesses arr tez les exercices imm diatement Do not allow children or people unfamiliar with the operation of this equipment on or near it Do not leave children unsupervised around the equipment Make sure all users wear proper exercise clothing and shoes for their workouts and avoid loose or dangling clothing Users should not wear shoes with heels or leather soles and they should check the soles of their shoes to remove any dirt and embedded stones They should also tie long hair back Never leave the equipment unattended when it is plugged in Unplug the equipment f
7. adjust the voltage requirements Failure to follow these instructions might damage the unit and void the Precor Limited Warranty After assembly is complete plug the power cord into an appropriate outlet Important The treadmill requires a 20 amp dedicated branch circuit Refer to Treadmill Grounding Instructions Breaking in the Equipment Precor equipment does not require an actual break in period However moving components such as belts gears and bearings can settle while the equipment is being stored or shipped This can cause the equipment to operate with a small amount of roughness or noise when it starts up for the first time The equipment usually returns to smooth operation after a day or two of normal use If it does not contact your dealer for assistance For more information refer to Obtaining Service 30 Assembling and Maintaining TRM 800 Series Treadmills Chapter 2 Installing the Console To make installation easier all Precor Experience Series consoles use the same mounting hardware and connector locations whenever possible The installation sequence for any of them is as follows e Threading the cable assembly e Connecting cables e Completing the installation tightening the mounting screws and attaching the back cover The following sections describe how to perform these tasks Threading the Cable Assembly P80 Earlier in the installation you threaded the necessary cables through the fram
8. and the screws aside Connecting Cables P80 After the console has been seated separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console Refer to the following diagram and table to identify the cables and connectors Figure 19 Cable connections P80 console Table 2 P80 internal cable connections Cable Connector Type Circuit Connector Location Ethernet LAN Eight contact modular on round black cable 34 Assembling and Maintaining TRM 800 Series Treadmills Cable Connector Type Circuit Connector Location TV in F type coaxial O Power Two contact plug 3 polarized and latched Data from base unit Eight contact modular on O flat gray cable Heart rate sensors Four contact strip keyed O Safety key Six contact strip keyed O treadmills only CSAFE Eight contact modular on QO flat gray cable Auto Stop sensor Four contact strip keyed O treadmills only To simplify installation and maintenance route and connect cables 1 through 5 according to the following instructions Note In the illustrations in this section some cables are omitted for the sake of clarity Connecting the Television Cable The console s television tuner is mounted inside the console s back plate The tuner includes a short cable adapter that allows the television cable to be connec
9. at the bottom of the console s back cover with the slots at the bottom of the console case Insert the tabs into the slots Insert the two 8 32 x Y inch Phillips head screws that you removed earlier into the holes at the top edge of the console s back cover Tighten the screws fully Important Use caution not to pinch the cables between the back cover and PVS mounting screw heads Fully tighten the four mounting screws partially tightened in step 3 using a 22 inch hex wrench 42 Assembling and Maintaining TRM 800 Series Treadmills Reassembling the Treadmill Fairing After the console is in place reattach the two cover panels of the treadmill fairing Important In the following procedure do not allow the fasteners to break or pinch any cables To reassemble the fairing 1 Verify that the cable assembly is secure inside the cable clips and that the ferrite bead on the base unit data cable is tied securely into place in the left arm of the treadmill 2 Snap the rear cover into place and attach the seven screws you removed with it earlier Figure 27 Removal and replacement of the rear fairing cover 3 Hold the center column cover in place and attach the two screws you removed with it Figure 28 Removal and replacement of the center column cover Installing the Console 43 Verifying That the Heart Rate Display Is Operational To verify that the heart rate display is operati
10. extra cable back into the neck tube Tilt the control console backward toward yourself until the tab on the top edge of its back plate slides along the top edge of the console mount and the screw holes align properly Insert the four inch flat head screws through the holes in the console mount and thread them into the holes in the back plate on the console Partially tighten the screws using a inch hex wrench Line up the two small tabs at the top of the console s back cover with the slots at the top of the opening in the console case Insert the tabs into the slots Insert the remaining tabs on the back cover with the corresponding slots on the console case Press gently on the edges of the back cover to snap it into place 38 Assembling and Maintaining TRM 800 Series Treadmills Threading the Cable Assembly P30 and P20 Earlier in the installation you threaded the necessary cables through the frame of the base unit and out the passthrough opening in the console mount As you line up the back plate on the console with the console mount you must make sure that the cable assembly passes correctly through the openings in both components Important Before you begin the following procedure remove the rear cover from the control console Set the cover and its mounting hardware aside for later use To thread the cable assembly 1 Make sure that as much of each cable as possible passes through the opening i
11. for Experience Series consoles and Preva Networked Fitness software is available at http www precor com productmanuals You may want to check in for updated information from time to time as the universe of Preva features expands Table of Contents Important Safety Instructions s ssssssusssnnsnnnnnnnnnnnnnunnunnnnnnnnnnnnnnnn 3 Safety Precautions stisssssesiiadaegdeisinindivaaiiindcn anima aie 3 Safety Cod eeu ccasieaiin aia aw ais SNA Rs Se eae 5 Educating USers sonenn a at 6 Hazardous Materials and Proper DispOSal c cccssssessesesseseecen 6 Product Recycling and Disposal c cccccscsesescesessestestssesceseeseeteseeees 7 Regulatory Notices for the RFID Module cccccesesesceeeeeteseeees 7 Regulatory Notices for Cardiovascular ExerciSe EQUIPMENE unanini ii 9 Treadmill Grounding Instructions cccccsessessecseesessessteseestesneeteanes 11 Electrical Recommendations 120 V and 240 V Treadmills vesiccscescsedancgenaticnciea nnna 11 Obtaining Service inset cacte ksi Wah eae ee 12 Obtaining Updated DOCUMENTATION cccsesessessestessestesseeneenees 12 Assembling the Treadmill ssscsssecsssessssesssessseessseeenseneees 15 Installation REQUIFEMENKS ccccsecsesesesessssnesessssesssessnestsessneeteetsnees 16 Unpacking the Cables c cccccsessssessssscssssssessesnsssssnssessseessssensasees 18 Assembling the Frame cceccccscsscsecesesessesssecsssncssseesesssessesesessneeeees 20 Completing Assembly cccccccsssssss
12. is properly grounded Do not modify the plug provided with the treadmill If the plug does not fit the outlet have a proper outlet installed by a qualified electrician Electrical Recommendations 120 V and 240 V Treadmills Note This is a recommendation only NEC National Electric Code guidelines or local region electric codes must be followed You should have received a power cable that meets your local electrical code requirements along with the equipment Precor treadmills must be connected to a 20 amp isolated branch circuit that can be shared only with one PVS If you need additional help with the power connections contact your Precor authorized dealer 12 Assembling and Maintaining TRM 800 Series Treadmills Important An individual branch circuit provides a hot conductor and neutral conductor to a receptacle The conductors must not be looped daisy chained or connected to any other conductors The circuit must be grounded according to NEC guidelines or local region electric codes Figure 2 North American 240 volt 20 amp power receptacle Obtaining Service Do not attempt to service the equipment except for maintenance tasks If any items are missing contact your dealer For more information regarding customer support numbers or a list of Precor authorized service centers visit the Precor web site at http www precor com Obtaining Updated Documentation Current documentation
13. on the right hand side of the fairing position 2 in the preceding illustration Important In the following step make sure that the end of the data cable with the ferrite bead is the upper end Likewise on the automatic stop sensor cable the three conductor socket is the lower end and the four conductor socket is the upper end 20 Assembling and Maintaining TRM 800 Series Treadmills 6 Remove any tape or ties that secure the cables then unwind them and remove any kinks Gather the cables into a single bundle referred to later as the cable assembly Note Arranging the cables so that the connectors are slightly staggered at the bottom end but still within one inch or three centimeters overall can help when feeding the cable assembly through narrow openings in the frame Assembling the Frame DANGER Make sure that the treadmill is not connected to any power source before you begin the following procedures As you add the left hand and right hand upright supports to the treadmill base you will need to make sure that the cable assembly is threaded properly through the left hand support so that the necessary connections are available when you add the control console A fish tape a thin metal strip with a hook or clasp on one end available from professional hardware vendors can be helpful during this procedure To begin assembly of the frame 1 Remove the hood and set it aside Figure 6 Hood r
14. 1 489 3 V1 4 1 e EN 301489 1 V1 8 1 e EN 60950 1 Regulatory Notices for Cardiovascular Exercise Equipment The regulatory information in this section applies to the exercise equipment and its control console Safety Approvals for Cardiovascular Equipment Precor equipment has been tested and found to comply with the following applicable safety standards Cardiovascular Type Equipment e CAN CSA IEC EN 60335 1 Household and similar electrical appliances Safety e EN 957 Stationary training equipment class S B compliant equipment PVS and P80 Regulatory Notice This Precor equipment has been tested and found to comply with the following applicable safety standards e CAN CSA UL IEC EN 60065 Audio video and similar electronic apparatus Safety 10 Assembling and Maintaining TRM 800 Series Treadmills Radio Frequency Interference RFI This Precor exercise equipment conforms to the following national standards defining acceptable limits for radio frequency interference RFI Federal Communications Commission Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a commercial installation The equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the owner s manual instr
15. AUTION Take special care when aligning the running belt Turn OFF the treadmill while adjusting or working near the rear roller Do NOT wear loose clothing or allow your hair to hang loose during this procedure Be very careful to keep your fingers and any other object clear of the belt and rollers especially in front of the roller and behind the deck The treadmill will not stop immediately if an object becomes caught in the belt or rollers To align the running belt 1 Make sure that the running surface is as level as possible If necessary adjust the rear feet as shown in the Assembly Guide to level the treadmill Note Adjusting the rear feet cannot compensate for extremely uneven surfaces If you cannot make the running surface level and stable move the treadmill 2 Turnthe treadmill ON 3 Standing beside the treadmill not on it press GO on the console 4 If necessary enter the safety code by pressing the number keys in sequence The running belt starts automatically after a 3 second countdown appears on the console 5 Press the SPEED UP key until the console shows a speed of 3 mph 5 kph CAUTION If you hear any chafing or the running belt appears to be getting damaged stop the running belt immediately by pressing the red STOP button Contact Precor Customer Support 50 Assembling and Maintaining TRM 800 Series Treadmills 6 Observe the belt from the rear of the treadmill for a few minutes The belt sho
16. Assembling and Maintaining TRM 800 Series Treadmills NPRECOR Assembling and Maintaining TRM 800 Series Treadmills MPRECOR Edition Information ASSEMBLING AND MAINTAINING TRM 800 SERIES TREADMILLS P N 300713 341 rev G Copyright February 2011 Precor Incorporated All rights reserved Specifications subject to change without notice Trademark Note Precor AMT and EFX are registered trademarks and Preva is a trademark of Precor Incorporated Other names in this document may be the trademarks or registered trademarks of their respective owners Intellectual Property Notice All rights title and interests in and to the software of the Preva Business Suite the accompanying printed materials any copies of such software and all data collected via the Preva Business Suite are exclusively owned by Precor or its suppliers as the case may be Precor is widely recognized for its innovative award winning designs of exercise equipment Precor aggressively seeks U S and foreign patents for both the mechanical construction and the visual aspects of its product design Any party contemplating the use of Precor product designs is hereby forewarned that Precor considers the unauthorized appropriation of its proprietary rights to be a very serious matter Precor will vigorously pursue all unauthorized appropriation of its proprietary rights Precor Incorporated 20031 142nd Ave NE P O Box 7202 Woodinville WA 98072 4002 1
17. PRESS WARRANTIES GIVEN ABOVE FOR THOSE SAME PARTS PRECOR HEREBY DISCLAIMS AND EXCLUDES THOSE WARRANTIES THEREAFTER Some States do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you PRECOR ALSO HEREBY DISCLAIMS AND EXCLUDES ALL OTHER OBLIGATIONS OR LIABILITIES EXPRESS OR IMPLIED ARISING BY LAW OR OTHERWISE WITH RESPECT TO ANY NONCONFORMANCE OR DEFECT IN ANY PRODUCT INCLUDING BUT NOT LIMITED TO A ANY OBLIGATION LIABILITY RIGHT CLAIM OR REMEDY IN TORT WHETHER OR NOT ARISING FROM THE NEGLIGENCE OF PRECOR OR ITS SUPPLIERS WHETHER ACTIVE PASSIVE OR IMPUTED AND B ANY OBLIGATION LIABILITY RIGHT CLAIM OR REMEDY FOR LOSS OF OR DAMAGE TO ANY EQUIPMENT This disclaimer and release shall apply even if the express warranty set forth above fails of its essential purpose Exclusive Remedies For any product described above that fails to conform to its warranty Precor will provide at their option one of the following 1 repair 2 replacement or 3 refund of the purchase price Precor Limited Warranty service may be obtained by contacting the authorized dealer from whom you purchased the item Precor compensates Servicers for warranty trips within their normal service area to repair commercial equipment at the customer s location You may be charged a trip charge outside the service area THESE SHALL BE THE SOLE AND EXCLUSIVE REMEDIES OF THE BUYER FOR ANY BREACH OF WARRANTY 60 Ass
18. a stationary handrail or handlebar while assuming the starting position on the equipment Face the console at all times On treadmills straddle the running belt and attach the safety clip to clothing at waist level before touching the control console Important For safety make sure users step onto the running belt while it is moving at or below 1 mile per hour 1 6 kilometers per hour Hold on to a stationary handrail or handlebar with one hand whenever you operate the console keys with the other hand Hazardous Materials and Proper Disposal The batteries within self powered equipment contain materials that are considered hazardous to the environment Federal law requires proper disposal of these batteries If you plan to dispose of your equipment contact Precor Commercial Products Customer Support for information regarding battery removal Refer to Obtaining Service Important Safety Instructions 7 Product Recycling and Disposal This equipment must be recycled or discarded according to applicable local and national regulations Product labels in accordance with European Directive 2002 96 EC concerning waste electrical and electronic equipment WEEE determine the framework for the return and recycling of used equipment as applicable throughout the European Union The WEEE label indicates that the product is not to be thrown away but rather reclaimed upon end of life per this Directive In accordance with the Europe
19. an WEEE Directive electrical and electronic equipment EEE is to be collected separately and to be reused recycled or recovered at end of life Users of EEE with the WEEE label per Annex IV of the WEEE Directive must not dispose of end of life EEE as unsorted municipal waste but use the collection framework available to customers for the return recycling and recovery of WEEE Customer participation is important to minimize any potential effects of EEE on the environment and human health due to the potential presence of hazardous substances in EEE For proper collection and treatment refer to Obtaining Service Regulatory Notices for the RFID Module When equipped with a control console as described in this document this equipment may include a radio frequency identification RFID module The RFID module has been certified to operate at temperatures between 20 C and 85 C 4 F and 185 F 8 Assembling and Maintaining TRM 800 Series Treadmills Radio Frequency Interference RFD The RFID module conforms to the following national standards defining acceptable limits for radio frequency interference RFI Federal Communications Commission Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a commercial installation The equipment generates uses
20. and can radiate radio frequency energy and if not installed and used in accordance with the owner s manual instructions can cause harmful interference to radio communications Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation WARNING Per FCC rules changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment Industry Canada This device complies with RSS 210 2007 of the Spectrum Management amp Telecommunications Radio Standards Specification Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada ATTENTION Haute Tension D branchez avant de r parer Important Safety Instructions European Applications CE compliance is claimed to the following directives e 1999 5 EC R amp TTE Directive e 2006 95 EC LVD Directive e 2002 95 EC RoHS Directive Directive compliance has been verified to the following standards e N55022 e EN 300 330 1 V1 5 1 e EN 300 330 2 V1 3 1 e EN 30
21. assemble this unit DO NOT attempt assembly by yourself To prepare the treadmill for assembly I Have your assistant help place the shipping carton close to the location where you plan to use the treadmill Break down the sidewalls of the shipping carton so that they lie flat Remove the loose contents of the carton CAUTION Use safe lifting techniques throughout the following steps To prevent injury to yourself or damage to the equipment obtain appropriate assistance before removing the unit from the pallet With the help of as many assistants as necessary lift the treadmill off of the pallet and roll it gently onto the floor Make sure that the power switch is OFF Check the ON OFF power switch on the front of the treadmill Place the switch in the O OFF position Make sure that the treadmill is not plugged into a power source Note In the following step do not roll the treadmill over its power cord Lift the unit by placing hands on opposite sides of the rear cross brace found under the treadmill s running belt Roll the treadmill on its front wheels to the area where it will be used 16 5 6 Assembling and Maintaining TRM 800 Series Treadmills Remove the shipping fasteners from the front panel using a Ys inch hex key and a 12 inch box end wrench Remove any tape or wire ties securing the console cable to the side of the unit Before you begin verify that you have received the following parts
22. bor 1 year 880 Line Commercial Cardiovascular Products superseding the coverage above where applicable Labor on the P80 console 2 years High wear items on the P80 console including headphone jack USB connector and iPod connector 90 days 58 Assembling and Maintaining TRM 800 Series Treadmills Options Accessories Many options or accessories have components that are connected internally or mounted inside the electronic console The following guidelines determine the warranty for these components If the internal components are installed by the factory or by an authorized dealer as part of the original sale and delivery they have a warranty that is identical to the warranty of the equipment in which they are connected or mounted If the internal components are not installed by the factory or by an authorized dealer as part of the original sale and delivery they have a 90 days parts and labor limited warranty All components that are not internally connected have a 90 days parts only limited warranty Satisfactory proof of purchase is required in all cases Conditions and Restrictions This warranty is valid only in accordance with the conditions set forth below 1 The warranty applies to the Precor product only while a it remains in the possession of the original purchaser and proof of purchase is demonstrated b it has not been subjected to accident misuse abuse improper service or non Precor modification c c
23. ccording to the manufacturer s instructions for more information visit www daleyinternational com 46 Assembling and Maintaining TRM 800 Series Treadmills Alternatively you can clean the equipment with Athletix fitness equipment cleaning wipes for more information visit www athletixproducts com CAUTION Read and follow the manufacturer s instructions particularly dilution instructions before using any cleaner on Precor fitness equipment Do not use concentrated cleaners at full strength or acidic cleaners of any kind such cleaners weaken the protective finish on the equipment and void the Precor Limited Warranty Never pour water or spray liquids onto any part of the equipment Allow the equipment to dry completely before using Vacuum the floor underneath the equipment frequently to prevent the accumulation of dust and dirt that can interfere with its operation Use a soft nylon scrub brush to clean the running belt CAUTION On treadmills as you clean the hood or side rails remain aware of the handrail extensions to avoid injury Daily Inspection At least once every day examine the equipment for the following problems e Slipping belts e Loose fasteners e Unusual noises e Worn or frayed power cords e Worn damaged or missing safety lanyards or clips e Any other indication that the equipment may be in need of service Important If you determine that the equipment needs service disconnect all power connec
24. e of the base unit and out the passthrough opening in the console mount As you line up the back plate on the console with the console mount you must make sure that the cable assembly passes correctly through the openings in both components 32 Assembling and Maintaining TRM 800 Series Treadmills Important Before you begin the following procedure remove the rear cover from the contro console To remove the cover use your fingernails to pry the lower edge loose then swing the cover up and out as shown in the following illustration Figure 17 Removing the access cover from the P80 console To thread the cable assembly 1 Make sure that as much of each cable as possible passes through the opening in the middle of the console mount on the base unit 2 Position the console over the console mount 3 Rest the console on the console mount so that the notch on the bottom of the console s back plate rests on the rectangular hook at the bottom of the console mount as shown in the following figure Figure 18 Console positioning on base unit Installing the Console 33 4 Tilt the console forward until it stops Use one hand to steady the console in this position or ask your assistant to do so 5 Using a 2 Phillips screwdriver remove the two 8 32 x Ya pan head machine screws securing the upper back cover of the fairing as shown in the previous figure Set the cover
25. embling and Maintaining TRM 800 Series Treadmills EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES PRECOR AND OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY WHETHER ARISING IN CONTRACT INCLUDING WARRANTY TORT INCLUDING ACTIVE PASSIVE OR IMPUTED NEGLIGENCE AND STRICT LIABILITY OR OTHERWISE FOR DAMAGE TO THE EQUIPMENT PROPERTY DAMAGE LOSS OF USE REVENUE OR PROFIT COST OF CAPITAL COST OF SUBSTITUTE EQUIPMENT ADDITIONAL COSTS INCURRED BY BUYER BY WAY OF CORRECTION OR OTHERWISE OR ANY OTHER INCIDENTAL SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE MISUSE OR INABILITY TO USE THE PRODUCT This exclusion applies even if the above warranty fails of its essential purposes and regardless of whether such damages are sought for breach of warranty breach of contract negligence or strict liability in tort or under any other legal theory Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Complete this portion and keep for your records Purchased From Example Dealer or store name Phone Number Example Dealer or store telephone number Product model Example AMT 885 or EFX 883 Serial number The serial number is found on the shipping container
26. embly through the cable guides in the fairing then wrap the guides around the cable assembly to secure it Push any extra cable into the upright support Note In the following step use the zinc finish buttonhead screws and flat washers from the hardware kit Important Do not wrench tighten the fasteners in the following step until the unit has been fully assembled Make sure the fasteners do not pinch any cables The Precor Limited Warranty does not cover cables damaged by improper installation Secure the fairing assembly using six buttonhead screws and six washers Partially tighten the fasteners Figure 10 Handrail and console assembly attachment Position the ferrite bead on the lower unit data cable inside the left arm of the fairing and secure it in place using a plastic tie Assembling the Treadmill 25 Completing Assembly After the upright supports and the fairing are in place replace the hood on the treadmill base and finish securing the fasteners CAUTION Be aware of the handrail extensions when you are working around the front of the unit It is easy to bump your head or sustain other injuries if you ignore the location of the handrail extensions To secure the fasteners 1 Using an alternating order tighten the eight fasteners that secure the upright supports to the treadmill base 2 Fully tighten the six screws that secure the console fairing to the upright supports To complete asse
27. emoval 2 Place the right hand upright support into the base frame side bracket Assembling the Treadmill 3 21 Secure the right hand upright support to the side bracket using four socket head screws four black washers and two locknuts Partially tighten the fasteners Figure 7 Upright support attachment right side Using the fabric connectors provided attach the power supply to the right hand side of the front crossmember on the treadmill base The gray rectangle in the following illustration shows where you should mount the power supply Route the DC output cable of the power supply through the clips between the power supply and the belt motor Pass the end of the cable under the mounting bracket for the lift motor Connect the black three conductor plug on the AC wiring harness to the socket on the power supply 22 Assembling and Maintaining TRM 800 Series Treadmills To thread cables through the frame 1 Feed the cable assembly downward through the left hand upright support and out through the opening in the lower end of the support Drape the remaining cable over the front of the support and tape it into place if necessary to secure it temporarily Feed the cable assembly through the grommet in the left hand side bracket of the base frame Connect the individual cables as shown in the following illustration and table Q
28. ence heart rate acquisition Except in Canada Precor does not pay labor outside the United States Warranties outside the United States and Canada may vary Please contact your local Dealer for details NO Commercial Cardiovascular Equipment Limited Warranty 59 This Limited Warranty shall not apply to 1 Software version upgrades 2 Software defects that do not materially and negatively affect the normal performance of the product under normal conditions of use 3 Consumable goods or cosmetic items of the product the exterior of which has been damaged or defaced as a result of abuse misuse accident improper service or installation mishandling or modification in design or construction not authorized by Precor 4 Repairs performed on Precor equipment missing a serial number or with a serial tag that has been altered or defaced 5 Service calls to correct installation of the equipment or instruct owners on how to use the equipment 6 Pickup and delivery involved with repairs 7 Any labor costs incurred beyond the applicable labor warranty period Disclaimer and Release The warranties provided herein are the exclusive warranties given by Precor and supersede any prior contrary or additional representations whether oral or written ANY IMPLIED WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT APPLY TO ANY PARTS DESCRIBED ABOVE ARE LIMITED IN DURATION TO THE PERIODS OF EX
29. er and moisture Avoid dropping anything on or spilling anything inside the equipment to prevent electric shock or damage to the electronics Do not operate electrically powered equipment in damp or wet locations Never operate this equipment if it has a damaged cord or plug if it is not working properly or if it has been dropped damaged or exposed to water Call for service immediately if any of these conditions exist Maintain the equipment to keep it in good working condition as described in the Maintenance section of the assembly and maintenance guide Inspect the equipment for incorrect worn or loose components and then correct replace or tighten prior to use Important Safety Instructions 5 e When using the treadmill always attach the safety clip to your clothing before beginning your workout Failure to use the safety clip may pose a greater risk of injury in the event of a fall e Also verify that the running belts on treadmills are clean and running smoothly e Do not allow runners over 350 pounds 160 kg or walkers over 500 pounds 225 kg to use the treadmill e If you plan to move the equipment obtain help and use proper lifting techniques Refer to the Moving the Equipment section of the assembly and maintenance guide e Use the equipment only for its intended purpose as described in this manual Do not use accessory attachments that are not recommended by Precor Such attachments may cause injuries
30. h Instruct users on how important it is to use the safety clip while exercising on the treadmill and demonstrate how they should attach it to their clothing near the waistline Treadmill Safety Features 55 If the restart switch trips during exercise perform the following steps 1 Reattach the safety clip if necessary 2 Press the restart switch down until it clicks returning it to its normal position Note If the restart switch trips all information about the current workout is deleted 3 Start the workout from the beginning reducing the time as needed to account for the amount of exercise that has been completed Figure 31 Attaching the safety clip Turning the Treadmill On and Off To turn the treadmill ON and OFF use the power switch located beneath the hood near the power cord receptacle Important When the treadmill is not being used turn it OFF Weight Limit Do not use the treadmill if you weigh more than 500 pounds 225 kg If you weigh more than 350 pounds 160 kg do not run on the treadmill Location The area around the treadmill must remain open and free of interference from objects such as other equipment at all times In addition for user safety and proper maintenance an area three feet one meter wide by six feet two meters long must remain open and free of interference directly behind the running belt 56 Assembling and Maintaining TRM 800 Series Treadmills Cha
31. he console You must make sure the deck is level before allowing anyone to use the treadmill Important Observe the following precautions throughout this procedure e Adjust only one rear foot at a time e Do not raise the unit beyond 3 4 inch 2 cm e Install the unit only on an absolutely even surface Adjusting the rear feet cannot compensate for variations in the surface under the unit To level the treadmill 1 Place a bubble level across the running belt to see whether the treadmill is level Figure 15 Bubble level placement on running belt If the treadmill Then Is level Skip to the next procedure Is not level Continue with step 2 2 Position yourself next to the adjustable rear feet Important Be sure that your assistant uses proper lifting techniques in the following step 3 Aska capable assistant to lift the rear portion of the treadmill using proper lifting techniques Assembling the Treadmill 29 4 Adjust the rear feet as needed gt Figure 16 Leveling foot adjustment 5 Repeat steps 1 through 4 until the treadmill is level 6 If necessary adjust the rear feet so that the user s weight is distributed evenly on the treadmill Plugging In the Power Cord CAUTION Use the supplied power cord Do not remove or otherwise bypass the 3 prong plug with an adapter to use a non grounded outlet Do not plug the unit into a power transformer in an attempt to
32. he treadmill use the power cord clips to secure it to the side rail To attach the power cord clips 1 Wrap the clip around the power cord near the power switch at the front of the treadmill and clamp it shut 6 Figure 12 Clip placement on power cord Assembling the Treadmill 27 2 Insert the serrated portion of the clip into the hole located under the front of the unit on either side of the power switch Figure 13 Power cord placement under front of treadmill 3 Place the clips along the length of the power cord as needed while you direct the cord to the power outlet The holes found in the frame beneath the side rail are spaced 12 inches 31 cm apart along the length of the side rail Figure 14 Power cord placement under side of treadmill Checking Treadmill Alignment and Adjusting the Running Belt Before you allow anyone to use the treadmill you must check the alignment of the running belt and adjust it as needed For more information refer to Checking the Alignment of the Running Belt and Adjusting the Running Belt in the Maintenance chapter 28 Assembling and Maintaining TRM 800 Series Treadmills Leveling the Unit The treadmill deck must be absolutely level from side to side to keep the belt in alignment and ensure proper operation If the load is not equally distributed across the treadmill deck users may feel excessive vibration or observe it at t
33. laims are made within the warranty period 2 This warranty does not cover damage or equipment failure caused by electrical wiring not in compliance with electrical codes or Precor owner s manual specifications or failure to provide reasonable and necessary maintenance as outlined in the owner s manual 3 Precor is not responsible for Internet connectivity to its products This restriction applies to services such as those provided by an Internet service provider ISP and also to hardware related to Internet connectivity such as Ethernet cabling routers servers and switches 4 Precor is not responsible for the quality of television video audio or other media supplied to its products This restriction applies to services such as those provided by a cable or satellite television provider to signal strength and clarity and also to hardware related to the reception and delivery of television video audio and other media Such hardware can include but is not limited to audio video and radio frequency RF cabling connectors receivers modulators combiners distribution amplifiers splitters and so on 5 Precor cannot guarantee that the heart rate measurement system on its products will work for all users Heart rate measurement accuracy varies based on a number of factors including the user s physiology and age the method in which the heart rate measurement system is used external interference and other factors that may influ
34. mbly of the treadmill base Important Use your fingers to align and thread the four hood fasteners properly Then use a wrench to tighten the hood fasteners completely as described in the following step 1 Thread the four black buttonhead screws with black washers into their holes leaving gaps of about inch between the heads of the screws and the surface of the treadmill frame 2 Place the front of the hood on the two front screws Make sure the screws are aligned with the notches in the hood and the washers are outside the hood 3 Lower the back of the hood until the side screws rest inside the notches in the internal wall of the hood Make sure the washers are outside the internal wall on the same side as the screw heads 4 Tighten all four screws securely starting with the front screws 26 Assembling and Maintaining TRM 800 Series Treadmills Note Using a hex wrench reach through the openings in the outer sides of the hood to tighten the side screws Figure 11 Hood and fastener placement Attaching the Power Cord Clips This treadmill includes a set of clips that hold the power cord away from the incline lift movement and other potential sources of wear and damage Use these clips to secure the power cord to the base frame beneath the hood Important When attaching the power cord clips keep users safety and the placement of the power cord in mind If the power cord runs along the length of t
35. n the middle of the console mount on the base unit Position the console over the console mount Rest the console on the console mount so that the notch on the bottom of the console s back plate rests on the rectangular hook at the bottom of the console mount as shown in the following figure Figure 24 Console positioning on base unit Tilt the console forward until it stops Use one hand to steady the console in this position or ask your assistant to do so Pull all cables upward and forward until you can drape them over the top of the console s back plate Installing the Console 39 Connecting Cables P30 After the console has been seated separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console Refer to the following diagram and table to identify the cables and connectors Figure 25 Cable connections P30 console Table 3 P30 internal cable connections Cable Connector Type Circuit Connector Location Safety key Six contact strip keyed Q treadmills only Auto Stop sensor Four contact strip keyed 2 treadmills only Data from base unit Eight contact modular 3 on flat gray cable Heart rate sensors Four contact strip keyed 4 40 Assembling and Maintaining TRM 800 Series Treadmills Connecting Cables P20 After the console ha
36. onal i 2 Begin exercising on the equipment Grasp both touch sensitive handlebars Note The heart rate is read within ten seconds During that time the heart on the display flashes Look at the HEART RATE display After a few seconds a number appears indicating your heart rate If a number does not appear in the HEART RATE display check the cable connection to make sure it is properly connected 44 Assembling and Maintaining TRM 800 Series Treadmills Chapter 5 Maintenance To keep the equipment functioning properly perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklist Failure to maintain the equipment as described in this section could void the Precor Limited Warranty DANGER To reduce the risk of electrical shock always disconnect the equipment from its power source before cleaning it or performing any maintenance tasks If the equipment is self powered but also uses the optional power adapter disconnect the adapter Daily Cleaning Precor recommends that you clean the equipment before and after each exercise session To remove dust and dirt from the equipment wipe all exposed surfaces with a soft cloth that you have moistened with one of the following cleaners e A solution of 30 parts of water to 1 part of Simple Green for more information visit www simplegreen com e ENVIR O SAFE oxygen enhanced cleaner or multi task cleaner concentrate diluted a
37. pter Commercial Cardiovascular Equipment Limited Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR PRECOR INCORPORATED PRODUCT BY USING THE EQUIPMENT YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS Limited Warranty Precor Incorporated warrants all new Precor products to be free from defects in materials and manufacture for the warranty periods set forth below The warranty periods commence on the invoice date of the original purchase This warranty applies only against defects discovered within the warranty period and extends only to the original purchaser of the product Parts repaired or replaced under the terms of this warranty will be warranted for the remainder of the original warranty period only To claim under this warranty the buyer must notify Precor or your authorized Precor dealer within 30 days after the date of discovery of any nonconformity and make the affected product available for inspection by Precor or its service representative Precor s obligations under this warranty are limited as set forth below Warranty Periods and Coverage All Commercial Cardiovascular Products excluding StretchTrainer Strength Products and coverage specific to certain models and options as defined below Frame 7 years Treadmill drive motor 5 years Items subject to wear 1 year Allother parts including mechanical parts and electronic parts 2 years La
38. rom its power source when it is not in use before cleaning it and before providing authorized service Note The optional power adapter is considered a power source for self powered equipment Assembling and Maintaining TRM 800 Series Treadmills Use the power adapter provided with the equipment Plug the power adapter into an appropriate grounded power outlet as marked on the equipment Care should be taken when mounting or dismounting the equipment Read understand and test the emergency stop procedures before use Keep the power cord or optional power adapter and plug away from heated surfaces Route power cables so that they are not walked on pinched or damaged by items placed upon or against them including the equipment itself Ensure the equipment has adequate ventilation Do not place anything on top of or over the equipment Do not use ona cushioned surface that could block the ventilation opening Assemble and operate the equipment on a solid level surface Proper Location for Equipment a For all equipment other than treadmills Locate at least 40 inches 1 meter away from walls or furniture on either side of the equipment and 40 inches 1 meter away from objects behind the equipment 2 For treadmills Locate at least 40 inches 1 meter away from walls or furniture on either side of the treadmill and at least 80 inches 2 meters away from objects behind the treadmill Keep equipment away from wat
39. s and other hardware shipped with the console before you begin installation 18 Assembling and Maintaining TRM 800 Series Treadmills Unpacking the Cables To connect the console to the base unit you may need up to five cables as follows e Ethernet P80 only e Television P80 only e Power P80 only e Base unit data e Automatic stop sensor Auto Stop The first three of these cables are shipped with the P80 console The remaining two are shipped inside the treadmill fairing To unpack the cables 1 Open the box containing the P80 console Retrieve the Ethernet television and power cables 2 Remove the two screws holding the center column cover in place Remove the cover and set it aside along with the two screws Figure 3 Removal and replacement of the center column cover Assembling the Treadmill 19 3 Remove the seven screws holding the back cover in place Snap the back cover loose and set it aside along with the seven screws Figure 4 Removal and replacement of the rear fairing cover 4 Remove the two ends of the base unit data cable from the left arm of the fairing position 1 in the following illustration Route the shorter of the two cable ends into the fairing and extend the long end outward Figure 5 Cable storage locations in the treadmill fairing base unit data cable 1 and Auto Stop cable 2 5 Remove the Auto Stop cable from the tube
40. s been seated separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console Refer to the following diagram and table to identify the cables and connectors Figure 26 Cable connections P20 console Table 4 P20 internal cable connections Cable Connector Type Circuit Connector Location Data from base unit Eight contact modular on flat gray cable Heart rate sensors Four contact strip keyed Safety key Six contact strip keyed 3 treadmills only Auto Stop sensor Four contact strip keyed O treadmills only Installing the Console 41 Completing the Console Installation P30 and P20 Before you complete the final installation steps double check the connections you have made Make sure that all cables are fully and securely connected and that any unneeded cables are tied back properly To complete the installation 1 2 Feed extra cable back into the neck tube Tilt the control console backward toward yourself until the tab on the top edge of its back plate slides along the top edge of the console mount and the screw holes align properly Insert the four inch flat head screws through the holes in the console mount and thread them into the holes in the back plate on the console Partially tighten the screws using a inch hex wrench Line up the two small tabs
41. sition for moving 1 Press GO on the console 2 Increase the incline level to 4 or more 3 While the treadmill is running turn the main power switch OFF 4 Disconnect the treadmill s power cord Maintenance 51 Long Term Storage If you do not expect anyone to use the equipment for a long time perform the following tasks to prepare it for storage e Turn it OFF e If it has a power cord disconnect the cord e If it has an optional power adapter connect the adapter to prevent damage to the internal battery e Position it so that it will not become damaged and will not interfere with people or other equipment 52 Assembling and Maintaining TRM 800 Series Treadmills Chapter 4 Treadmill Safety Features Before allowing users on Precor equipment review the Important Safety Instructions in this manual You should also teach your patrons how to use the equipment safely according to the guidelines on Entering the Safety Code When the equipment is shipped from the factory safety code protection is not active After you have activated the safety code you must inform your patrons that the equipment requests a safety code to prevent unauthorized use They must complete the following steps to use the equipment To enter the safety code and start the treadmill 1 Assume the starting position with one hand free to enter the code and the other hand holding a handrail Important Hold the handrail securely
42. ssessesssssessessessesssssessseseesnsesesneess 25 Attaching the Power Cord Clips w cccsecssssssssesssssesssesesssssesneesesnes 26 Checking Treadmill Alignment and Adjusting the Rein mine Peline ERA E kal diele atthe 27 Leveling the Unit oc cccccsesessssessessssesseesssesseesssnsseesssnsssesssnsseesseess 28 Plugging In the Power Cord ieccssssssssscsessesssssesssssecssssssssssssneessaneees 29 Breaking in the Equipment uu ccesessesssceesesscsestssessssseseeseseseaneseees 29 Installing the Console sssssssssunueunnnunnnnnnnunnnunnnunnnunnnunnnnnnnnnnnnnnnnnnn 31 Threading the Cable Assembly P80 cccccssssssssessessesesseeseens 31 Connecting Cables P80 ccccsssssssssessecessssssssesssssesseessssnessesneess 33 Completing the Console Installation P80 wc cesses 37 Threading the Cable Assembly P30 and P20 veces 38 Connecting Cables P30 ssss sssssssssrrsrsnssssrrersnssssrrresnsnrnrrrrsnsnnnn 39 Connecting Cables P20 cccssssssesssssesesssssssssseesssseeesssessaseensens 40 Completing the Console Installation P30 and P20 41 Reassembling the Treadmill Fairing c ccccccccsescessssesceesseeceseeees 42 Verifying That the Heart Rate Display Is Operational 43 Assembling and Maintaining TRM 800 Series Treadmills Maintenance ssssccssssccsssessseeesseesssseeenseeesnnenseeesnssaeensneensneesenees 45 Dail Cleaning irane eeren saestecs dens ehaessnest canaries N 45 Daily INS pectinea a a a 46 Weekly Maintenance
43. ted outside the back plate To connect the television cable 1 2 Pull the cable out through the lower right corner of the back plate Route the cable counterclockwise around the outside of the back plate Attach the connector on the cable to the connector on the tuner cable and tighten the two connectors securely using two e inch open end wrenches Position both connectors above the upper right corner of the back plate Use a plastic tie to secure the connectors to the top of the back plate Pass the tie through the two small holes near the upper right corner of the back plate then wrap it around the connectors and tighten it securely Cut off and remove the protruding end of the tie Installing the Console 35 The following illustration shows how the cable is positioned once it is installed Figure 20 Connecting the television cable Connecting the Ethernet and Base Unit Data Cables Both the Ethernet and base unit data cables pass through the cutaway opening at the upper right corner of the back plate and connect to nearby modular jacks in the console Because of this it is important to exercise caution when connecting the cables The black Ethernet cable connects to a jack just underneath the perforated metal bracket at the very top of the opening in the console The gray base unit data cable connects to a lower jack closer to the back plate Refer to
44. the treadmill before making any adjustments Do not adjust the running belt when someone is standing on it Important This procedure uses the terms left and right as they would appear to a person standing behind the treadmill and facing the console Make all belt adjustments on the adjusting bolts at the rear corners of the treadmill using the hex key provided and do not turn either bolt more than turn before checking the alignment of the running belt again Overtightening the adjusting bolts can damage the treadmill To adjust the running belt 1 Locate the adjusting bolts in the end caps at the rear corners of the treadmill as shown in the following diagram Figure 29 Location of the adjustment bolt 2 Using the hex key move one of the adjusting bolts turn counterclockwise to loosen it Maintenance 49 If the belt tracks off center Then loosen To the left The right adjusting bolt To the right The left adjusting bolt 3 Recheck the belt position as described under Checking the Alignment of the Running Belt Note If slippage occurs tighten both adjusting bolts evenly until it stops Do not overtighten the belt Checking the Alignment of the Running Belt Proper alignment allows the belt to remain centered and ensures smooth operation Realigning the belt takes a few simple adjustments If you are unsure about this procedure call Precor Customer Support refer to Obtaining Service C
45. the following illustration for the correct position of both cables CAUTION If you connect the base unit data cable to the wrong jack the equipment will not function Figure 21 Connecting the Ethernet and base unit data cables 36 Assembling and Maintaining TRM 800 Series Treadmills Connecting the Heart Rate Sensor Cable The heart rate sensor cable passes through the cutaway opening at the upper left corner of the back plate then down to the small circuit board at the lower left of the console The following illustration shows how the cable should look once it is installed j Figure 22 Connecting the heart rate cable Connecting the Power Cable Like the tuner the console s upper circuit board is equipped with a cable adapter that relieves you of attempting to attach a cable to a recessed jack To connect the power cable route it through the cutaway opening at the upper left corner of the back plate and plug it in to this adapter The following illustration shows how the cable should look once it is installed Figure 23 Connecting the power cable Installing the Console 37 Completing the Console Installation P80 Before you complete the final installation steps double check the connections you have made Make sure that all cables are fully and securely connected and that any unneeded cables are tied back properly To complete the installation 1 2 Feed
46. tions television Ethernet and power and move the equipment away from the exercise area Place an OUT OF SERVICE sign on the equipment and make it clear to all patrons and other users that they must not use it To order parts or to contact a Precor authorized service provider in your area refer to Obtaining Service Maintenance 47 Weekly Maintenance Perform the following maintenance tasks every week 1 Elevate the tread to maximum incline then turn off the power switch or circuit breaker and unplug the unit from the wall outlet Clean the floor under the equipment using a vacuum cleaner or a damp mop When the floor is completely dry reconnect the power and return the treadmill to the level position Inspect the power cord to verify that it is not pinched under the equipment or between any two moving parts Test all console functions including heart rate monitoring features Verify that the unit sits squarely on the floor All of its feet should be touching the floor and the unit should not rock or wobble when in use If not re level it as described in Leveling the Unit Monthly Maintenance DANGER USE EXTREME CAUTION when the rear cover of any EFX is removed Serious injury could result if fingers are pinched between the flywheel spokes cranks movable arms and the drive weldment Securing the movable arm to the crank with a clamp is recommended Be aware of other people within your work area who might ca
47. uctions may cause harmful interference to radio communications WARNING Per FCC rules changes or modifications not expressly approved by Precor could void the user s authority to operate the equipment Industry Canada This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada ATTENTION Haute Tension D branchez avant de r parer European Applications CE compliance is claimed to the following directives e 2004 108 EC EMC Directive e 2006 95 EC LVD Directive e 2002 95 EC RoHS Directive Directive compliance has been verified to the following standards e EN 55022 e EN 55024 e EN 60335 1 e EN 60065 P80 and PVS Important Safety Instructions 11 Treadmill Grounding Instructions The treadmill must be grounded If the equipment malfunctions or breaks down grounding draws off electric current and reduces the risk of electric shock The power cord on the treadmill is equipped with a grounding conductor and a three pin grounding plug This plug must be inserted into an outlet that is properly installed and grounded in accordance with all local codes and ordinances Failure to ground the treadmill properly may void the Precor Limited Warranty DANGER Improper connection of the grounding conductor can result in a risk of electric shock Check with a qualified electrician or service person if you are not sure whether the equipment
48. uld remain centered along the running bed If it drifts off center adjust it Refer to Treadmill Adjusting the Running Belt Important Failure to align the belt may cause the belt to tear or fray which is not covered by the Precor Limited Warranty 7 Press the red STOP button to stop the belt 8 Turn the treadmill OFF Storing the Chest Strap If you purchased the optional heart rate chest strap store it in a place where it remains free of dust and dirt for example in a closet or drawer Be sure to protect the chest strap from extremes in temperature Do not store it in a place that may be exposed to temperatures below 32 F 0 C To clean the chest strap use a sponge or soft cloth dampened in mild soap and water Dry the surface thoroughly with a clean towel Moving the Equipment The equipment is very heavy If you plan to move it to a new location obtain the help of an adult assistant and use proper lifting techniques If the equipment includes roller wheels on one end use the wheels to reduce the load on yourself and your assistant Important The plastic end caps on Precor treadmills are designed specifically for lifting Working with your assistant place a hand under each side of the end cap Then using proper lifting techniques lift the rear of the treadmill so that it rolls on its front wheels The treadmill can be easier to move if it is in an inclined position To put the treadmill into an inclined po
49. use the arm to move Perform the following maintenance tasks every month 1 2 Clean the frame cover and arms with water or an approved cleaner Wipe the exterior of the console with a damp sponge or soft cloth and dry with a clean towel Keep water away from electronic components to prevent electrical shock or damage Clean the touchscreen using a soft lint free cloth dampened with a 91 isopropyl alcohol solution either as sold or diluted with an equal amount of water Remove the rear cover Vacuum out any debris being careful not to bring the vacuum cleaner nozzle too close to any circuit board unless your vacuum cleaner is protected against static buildup 48 Assembling and Maintaining TRM 800 Series Treadmills 5 Check the belt tension of the step up and drive belts 6 Clean and lubricate the lift motor screw with an approved grease such as SuperLube with Teflon or Mobil 1 synthetic grease adjustable ramp models only 7 Check all fasteners for proper tightness and torque Replace all covers 9 Verify that the unit sits squarely on the floor All of its feet should be touching the floor and the unit should not rock or wobble when in use If not re level it as described in Leveling the Unit oo Adjusting the Running Belt If you are unsure about adjusting the running belt call Precor Customer Support refer to Obtaining Service CAUTION For your safety use the power switch to turn OFF
50. with at least one hand throughout the following steps 2 When you see the banner text on the console select a program or press GO 3 When you are prompted to enter the safety code and unlock the treadmill press the 1 2 3 and 4 keys in order If you have entered the code correctly the workout begins Otherwise the equipment pauses for two seconds and then prompts you to enter the code again Pressing five or more keys returns you to the initial safety code prompt Note On a treadmill a 3 second countdown appears on the console before the running belt starts to move 54 Assembling and Maintaining TRM 800 Series Treadmills Using the Treadmill Safety Clip The treadmill is equipped with two different stop functions which behave as follows If the user Then the And the console treadmill belt Presses down onthe red Slowstoa Shows that the exercise STOP button stop workout is paused Pulls on the lanyard Slows toa Shows the words PUSH TO attached to the safety stop RESET SWITCH and an clip and trips the restart arrow pointing to the switch Restart switch O The restart switch is located just below the console and immediately behind the red STOP button as shown in the following illustration When it is tripped the bar pops up displaying the words PUSH TO RESET SWITCH on its front side The treadmill does not operate while these words are visible Figure 30 Restart switc
Download Pdf Manuals
Related Search