Poulan 952711879 Trimmer User Manual
Contents
1. PP3000B Brushcutter PP4000C Pr ner sci so ses ac reson PT carats PP5000P A WARNING Always stop unit and dis connect spark plug before removing or instal ling attachments REMOVING TRIMMER ATTACH MENT OR OTHER OPTIONAL ATTACHMENTS CAUTION When removing or installing at tachments place the unit on a flat surface for stability 1 Loosen the coupler by turning the knob counterclockwise Coupler TIGHTEN 2 Press and hold the locking release button Locking Release Button HOT lt Attachment Coupler Upper Shaft 3 While securely holding the engine and upper shaft pull the attachment straight out of the coupler INSTALLING OPTIONAL ATTACH MENTS 1 Remove the shaft cap from the attach ment if present 2 Position locking release button of attach ment into guide recess of coupler 3 Pushthe attachment into the coupler until the locking release button snaps into the primary hole 4 Before using the unit tighten the knob se curely by turning clockwise Primary Hole Coupler Guide Recess ak Locking Release Attachment Button Upper Shaft WARNING Make sure the locking release button is locked in the primary hole and the knob is securely tightened before op erating the unit All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual Using the2. AWARNING This unit can be dangerous Careless or improper use can cause serious injury AWARNING Read the operator s manual before use Failure to follow instructions could result in serious injury to the operator and or bystanders Save operator s manual Trimmer line can throw objects violently You can be blinded or injured Always wear hearing protection and safety glasses marked Z87 Always wear head protection heavy long pants long sleeves boots and gloves Hazard zone for thrown objects e Trimmer line throws objects violently e You and others can be blinded injured e Keep children bystanders and animals 50 feet 15 meters away Secure hair above shoulder length Do not wear jewelry loose clothing or clothing with loosing hanging straps ties tassels etc They can be caught in moving parts Assist handle to be positioned only below the arrow IDENTIFICATION OF SAFETY SYMBOLS Never allow children to operate this unit Store unit indoors in a high dry place out of the reach of children When servicing unit use only identical replacement parts Always stop unit and disconnect spark plug before clean ing or servicing WARNING Fire hazard Never mix pour or store gasoline or use the unit near a flame or sparks including smoking open flames or work that can cause sparks Use unleaded gasoline and two stroke oil mixed at a ratio of 40 1 2 5 OPTIO
3. Wear hearing protection Never start or run inside a closed room or building Breathing exhaust fumes can kill Keep handles free of oil and fuel Keep handles free of oil and fuel Always keep engine on the right hand side of your body Hold the unit firmly with both hands Keep trimmer head or other optional attachment below waist level and away from all parts of your body Do not raise engine above your waist Keep all parts of your body away from muffler and spinning line or other optional attachment Keep engine below waist level A hot muffler can cause serious burns Keep firm footing and balance Do not overreach or use from unstable surfaces such as ladders trees steep slopes rooftops etc Use only in daylight or good artificial light Use only for jobs explained in this manual or manuals for optional attachments UNIT MAINTENANCE SAFETY Disconnect the spark plug before performing maintenance except carburetor adjustments Look for and replace damaged or loose parts before each use Look for and repair fuel leaks before use Keep in good working condition Replace trimmer head parts that are chipped cracked broken or damaged in any other way before using the unit Maintain unit according to recommended procedures Keep cutting line at proper length Use only 0 095 2 4 mm diameter Poulan PRO brand line Never use wire rope string etc Install required shield properly before using the unit Use
4. Poulan PRO Please do not return product to retailer Por favor no devuelva el producto al lugar de compra Veuillez ne pas retourner le produit au d taillant 1 800 554 6723 Register your product online at Registre su producto en linea en Enregistrez votre produit en ligne l adresse www poulanpro com Instruction Manual Manual de Instrucciones Manuel d Instructions PP125 For Occasional Use Only DANGER Read and follow all Safety Rules and Operating Instructions before using this product Failure to do so can result in serious injury PELIGRO Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad El no hacerlo puede resultar en le siones graves DANGER Lire le manuel d instructions et bien respecter tous les avertisse ments et toutes les instructions de s curit Tout d faut de le faire pourrait entrainer des blessures graves Poulan PRO Poulan PRO 7349 Statesville Road 850 Matheson Blvd West Charlotte NC 28269 Mississauga Ontario L5V 0B4 115273826 Rev 2 3 1 10 BRW m zZ a un T TONVdS43 SIVONVHYS IDENTIFICATION OF SAFETY SYMBOLS ADANG ER Use only specified trimmer head spool and 0 095 inch 2 4 mm recom mended trimmer line Never use blades flailing devices wire rope string etc This attachment is designed for line trimmer use only Failure to follow 9 these instructions may result in serious injury
5. Blade rotates momen tarily after the trigger is released or engine is turned off The blade can seriously cut you or others Allow blade to stop before removing it from the cut Throw away blades that are bent warped cracked broken or damaged in any other way Replace parts that are cracked chipped or damaged before using the unit Do not attempt to remove cut material nor hold material to be cut when the engine is running or when cutting blade is moving Always keep the wheel and depth adjusting skid in contact with the ground Always push the unit slowly over the ground Stay alert for uneven sidewalks holes in the terrain large roots etc BLOWER VACUUM SAFETY A WARNING Inspect area before starting unit Remove all debris and hard ob jects such as rocks glass wire etc that can ricochet be thrown or otherwise cause injury or damage during operation Do not set unit on any surface except aclean hard area while engine is running Debris such as gravel sand dust grass etc could be picked up by the air intake and thrown out through discharge opening damaging unit property or causing serious injury to bystanders or operator Never place objects inside the blower tubes vacuum tubes or blower outlet Always direct the blowing debris away from people animals glass and solid objects such as trees automobiles walls etc The force of air can cause rocks dirt or sticks to be thrown or to ricochet whic
6. always stop engine and ensure blade chain has stopped moving dis connect spark plug and wear gloves when changing or handling the blade or chain WARNING A coasting blade rotat ing chain can cause injury while it continues to move after the engine is stopped Maintain proper control of the unit until the blade chain has completely stopped moving Keep hands face and feet at a distance from all moving parts Do not attempt to touch or stop the blade or chain when it is moving A WARNING Falling objects can cause severe head injury Wear head protec tion when operating this unit with a pole prun er attachment A WARNING To prevent serious injury do not use more than one boom extension with a pole pruner attachment WARNING Keep the pruner away from power lines or electrical wires Only use for pruning limbs or branches overhead up to 6 inches 15 cm in diameter Do not operate the unit faster than the speed needed to prune Do not run the unit at high speed when not pruning Always stop the unit when work is delayed or when walking from one cutting location to another If you strike or become entangled with a foreign object stop the engine immediately and check for damage Have any damage repaired by an authorized service dealer before attempting further operations Discard blades that are bent warped cracked or broken Stop the unit immediately if you feel excessive vibration Vibration is a sign of
7. only specified trimmer head make sure it is properly installed and securely fastened Make sure unit is assembled correctly as shown in this manual Make carburetor adjustments with lower end supported to prevent line from contacting any object Keep others away when making carburetor adjustments Use only recommended Poulan PRO accessories and replacement parts Have all maintenance and service not explained in this manual performed by an authorized service dealer FUEL SAFETY Mix and pour fuel outdoors Keep away from sparks or flames Use a container approved for fuel Do not smoke or allow smoking near fuel or the unit Avoid spilling fuel or oil Wipe up all fuel spills Move at least 10 feet 3 meters away from fueling site before starting engine Stop engine and allow to cool before removing fuel cap Always store gasoline in a container approved for flammable liquids TRANSPORTING AND STORAGE Allow engine to cool secure unit before storing or transporting in vehicle Empty the fuel tank before storing or transporting the unit Use up fuel left in the carburetor by starting the engine and letting it run until it stops Store unit and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters electric motors or switches furnaces etc Store unit so line limiter blade cannot accidentally cause injury The unit can be hung by the shaft Store unit out of reach of children W
8. performance and durability problems A WARNING Alternative fuels not gas oline such as E 15 15 alcohol E 20 20 alcohol E 85 85 alcohol are NOT classified as gasoline and are NOT approved for use in 2 stroke gasoline engines Use of alternative fuels will cause problems such as improper clutch engagements overheating vapor lock power loss lubrication deficiency deterioration of fuel lines gaskets and internal carburetor components etc Alternative fuels cause high moisture absorption into the fuel oil mixture leading to oil and fuel separation HOW TO STOP YOUR UNIT e Release the throttle trigger e Push and release the engine ON STOP switch The switch will automatically return to engine starts allow the engine to warm up 10 15 seconds then fully squeeze the throttle trigger to deactivate the starting system COUPLER The COUPLER enables optional attach ments to be installed on the unit the ON position Wait 5 seconds before at tempting to restart unit to allow switch to reset a ON STOP Switch HOW TO START YOUR UNIT WARNING Avoid any contact with the muffler A hot muffler can cause serious burns HELPFUL TIP If your engine still does not start after following these instructions please call 1 800 554 6723 STARTING A COLD ENGINE NOTE DO NOT squeeze the throttle trigger until the engine has started and runs 1 Set unit on a flat surface 2 Slowly press the primer bulb 6 ti
9. rust Always wear gloves when servicing or cleaning the tines The tines become very sharp from use Do not run unit at high speed unless cultivating HEDGE TRIMMER SAFETY DANGER RISK oF CUT KEEP HANDS AWAY FROM BLADE Blade moves momentarily after the trigger is released or en gine is turned off Do not attempt to clear away cut material when the blade is in motion Make sure engine is turned off the spark plug wire is disconnected and the blade has stopped mov ing before removing jammed material from the Cutting blade Do not grab or hold the unit by the Cutting blade WARNING Inspect the area before Starting the unit Remove all debris and hard objects such as rocks glass wire etc that can ricochet be thrown or otherwise cause injury or damage during operation Do not use a Cutting blade that is bent warped cracked broken or damaged in any other way Have worn or damaged parts replaced by an authorized service dealer Always keep unit in front of your body Keep all parts of your body away from the cutting blade Keep the cutting blade and air vents clear of debris POLE PRUNER SAFETY WARNING The reciprocating blade rotating chain can cause severe injury In spect the unit before use Do not operate unit with a bent cracked or dull blade or dull chain Keep away from the blade chain A WARNING The reciprocating blade rotating chain is sharp Do not touch To pre vent serious injury
10. your nearest authorized service center call Poulan PRO at 1 800 554 6723 or send e mail correspondence to emission warranty HCOP emission com WHERE TO GET WARRANTY SERVICE Warranty services or repairs shall be provided at all Poulan PRO ser vice centers Call 1 800 554 6723 or send e mail correspondence to emission warranty HCOP emission com _ MAINTENANCE REPLACEMENT AND REPAIR OF EMIS SION RELATED PARTS Any Poulan PRO approved replacement part used in the per formance of any warranty maintenance or re pair on emission related parts will be provided without charge to the owner if the part is under warranty EMISSION CONTROL WARRAN TY PARTS LIST Carburetor air filter covered up to maintenance schedule ignition system spark plug covered up to maintenance sched ule ignition module muffler including catalyst if equipped fuel tank MAINTENANCE STATEMENT The owner is responsible for the performance of all required maintenance as defined in the instruction manual The information on the product label indicates which standard your engine is certified Example Year EPA and or CALIFORNIA EMISSION CONTROL INFORMATION THIS ENGINE MEETS EXH AND EVAP EMISSIONS REGULATIONS FOR SMALL OFF ROAD ENGINES POULAN WEED EATER 2010 US EPA CALIF FAMILY DISP MODELE COMPLIANCE PERIOD HOURS BAR CODE THE AIR INDEX OF THIS ENGINE IS THE LOWER THE AIR INDEX THE LESS POLLUTION REFER TO OWNER S MANUAL FOR MAINTENANC
11. ANTY RIGHTS AND OB LIGATIONS The U S Environmental Protection Agency California Air Resources Board Environment Canada and Poulan PRO are pleased to explain the emissions con trol system warranty on your year 2010 and lat er small off road engine In California all small off road engines must be designed built and equipped to meet the State s stringent anti smog standards Poulan PRO must warrant the emission control system on your small off road engine for the periods of time listed below provided there has been no abuse ne glect or improper maintenance of your small off road engine Your emission control system includes parts such as the carburetor the igni tion system and the fuel tank Where a warrant able condition exists Poulan PRO will repair your small off road engine at no cost to you Expenses covered under warranty include diagnosis parts and labor MANUFACTURER S WARRANTY COV ERAGE If any emissions related part on your engine as listed under Emissions Control Warranty Parts List is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part the part will be repaired or replaced by Poulan PRO OWNER S WARRANTY RE SPONSIBILITIES As the small off road en gine owner you are responsible for the per formance of the required maintenance listed in your instruction manual Poulan PRO rec ommends that you retain all receipts covering maintenanc
12. ARNING The engine exhaust from this product contains chemicals known tothe State of California to cause cancer birth defects or other reproductive harm SAFETY NOTICE Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers hands and joints of people prone to circulation disorders or abnor mal swellings Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people If symptoms occur such as numbness pain loss of strength change in skin color or texture or loss of feeling in the fingers hands or joints discontinue the use of this tool and seek medical attention An anti vibration system does not guarantee the avoidance of these problems Users who oper ate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool SPECIAL NOTICE This unit is equipped with a temperature limiting muffler and spark arresting screen which meets the require ments of California Codes 4442 and 4443 All U S forest land and the states of California Idaho Maine Minnesota New Jersey Ore gon and Washington require by law that many internal combustion engines be equipped with a spark arresting screen Ifyou operate in a locale where such regulations ex ist you are legally responsible for maintaining the operating condition of these parts Failure to do so is a violation of t
13. E SPECIFICATIONS AND ADJUSTMENTS This engine is certified to be emissions compliant for the following use X Moderate 50 hours L Intermediate 125 hours L Extended 300 hours 18
14. ENGINE A WARNING Be sure to read the fuel information in the safety rules before you be gin If you do not understand the safety rules do not attempt to fuel your unit Call 1 800 554 6723 FUELING ENGINE A WARNING Remove fuel cap slowly when refueling HELPFUL TIP To obtain the correct oil mix ratio pour 3 2 ounces of 2 cycle synthetic oil into one gallon of fresh gas This engine is certified to operate on un leaded gasoline Before operation gasoline must be mixed with a good quality synthetic 2 cycle air cooled engine oil designed to be mixed at a ratio of 40 1 Poulan WEED EATER brand synthetic oil is recommended Mix gaso line and oil at a ratio of 40 1 A 40 1 ratio is ob tained by mixing 3 2 ounces 95 ml of oil with 1 gallon 4 liters of unleaded gasoline DO NOT USE automotive oil or marine oil These oils will cause engine damage When mixing fuel follow instructions printed on container Once oil is added to gasoline shake container mo mentarily to assure that the fuel is thoroughly mixed Always read and follow the safety rules relating to fuel before fueling your unit CAUTION Never use straight gasoline in your unit This will cause permanent engine damage and void the limited warranty FUEL REQUIREMENTS This engine requires the use of minimum 87 octane R M 2 clean gasoline IMPORTANT Use of alcohol blended fuels called gasohol or using ethanol or methanol can cause major en gine
15. Fueling Engine in Operation hot section Replace with correct spark plug Contact an authorized service dealer Contact an authorized service dealer 16 LIMITED WARRANTY Poulan PRO a division of Husqvarna Consum er Outdoor Products N A Inc warrants to the original consumer purchaser that each new Poulan PRO brand gasoline tool or attachment is free from defects in material and workman ship and agrees to repair or replace under this warranty any defective gasoline product or at tachment as follows from the original date of purchase 2 YEARS Parts and Labor when used for household purposes 90 DAYS Parts and Labor when used for commercial professional or income producing purposes 30 DAYS Parts and Labor if used for rental purposes This warranty is not transferable and does not cover damage or liability caused by improper handling improper maintenance or alteration or the use of accessories and or attachments not specifically recommended by Poulan PRO for this tool This warranty does not cover tune up spark plugs filters starter ropes cutting line or rotating head parts that will wear and require re placement with reasonable use during the war ranty period This warranty does not cover pre delivery setup or normal adjustments explained in the instruction manual This warranty does not cover transportation costs In the event you have a claim under this warran ty you must retu
16. NAL ATTACHMENTS These attachments used in combination with the specified powerhead have been evaluated to ANSI B175 3 2003 Grass Trimmers and Brushcutters Safety Requirements Powerhead including trimmer attachment PP125 Brushcutter attachment PP4000C These attachments used in combination with the specified powerhead have been evaluated to appli cable ISO and EN safety requirement standards by the Swedish Machinery Testing Institute Edger attachment sisse facta distew eae RE canara on arte Gee ee PP1000E Cultivator attachment 222 PP2000T Blower attachment re nu Net sn heen weasel esky yom enue mr PP3000B Pr ner attachment osu cer diem es CRA SEE Ee Re RE Ree eee baer es PP5000P SAFETY RULES WARNING When using gardening appliances basic safety precautions must al ways be followed to reduce the risk of fire and serious injury Read and follow all instruc tions This power unit can be dangerous Operator is responsible for following instructions and warnings on unit and in manual Read entire instruction manual before using unit Be thor oughly familiar with the controls and the prop er use of the unit Restrict the use of this unit to persons who have read understand and will follow the instructions and warnings on the unit and in the manual Never allow chil dren to operate this unit E
17. NG TRIMMER ATTACH MENT CAUTION When installing trimmer attach ment place the unit on a flat surface for stabil ity H Loosen the coupler by turning the knob counterclockwise Coupler TIGHTEN the locking release button snaps into the primary hole 6 Before using the unit tighten the knob se curely by turning clockwise Primary Hole Guide Recess Coupler ing Upper Pang Attachment Shaft Button WARNING Make sure the locking release button is locked in the primary hole and the knob is securely tightened before op erating the unit All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual Using the wrong hole could lead to seri ous injury or damage to the unit Locking Release Button in Primary Hole For assembly of optional attachments see list on page 11 refer to the ASSEMBLY sec tion of the applicable attachment instruction manual ATTACHING THE SHIELD A WARNING The shield must be prop erly installed The shield provides partial protec tion from the risk of thrown objects to the opera tor and others and is equipped with a line limiter blade which cuts excess line to the proper length The line limiter blade on underside of shield is sharp and can cut you For proper orientation of shield see KNOW YOUR TRIMMER illustration in OPERATION section 1 Remove wing nut from shield 2 Insert bracket
18. T SAFETY INFORMATION ON THE UNIT INSTRUCTION MANUAL A DANGER Never use blades with line trimmer attachment Never use flailing devices with any attachment This unit when used with supplied line trimmer attachment is designed for line trimmer use only Use of any other ac cessories or attachments with line trimmer at tachment will increase the risk of injury If situations occur which are not covered in this manual use care and good judgment If you need assistance contact your authorized service dealer or call 1 800 554 6723 OPERATOR SAFETY Dress properly Always wear safety glasses or similar eye protection when operating or performing maintenance on your unit safety glasses are available Eye protection should be marked Z87 Always wear face or dust mask if operation is dusty Always wear heavy long pants long sleeves boots and gloves Wearing safety leg guards is recommended Always wear foot protection Do not go barefoot or wear sandals Stay clear of spinning line Secure hair above shoulder length Secure or remove loose clothing or clothing with loosely hanging ties straps tassels etc They can be caught in moving parts Being fully covered also helps protect you from debris and pieces of toxic plants thrown by spinning line Stay Alert Do not operate this unit when you are tired ill upset or under the influence of alcohol drugs or medication Watch what you are doing use common sense
19. decals using a damp cloth with a mild deter ent Wipe off unit with a clean dry cloth CLEAN AIR FILTER A dirty air filter decreases engine perform ance and increases fuel consumption and harmful emissions Always clean after every 5 hours of operation 1 Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is removed 2 Remove parts by pressing button to re lease air filter cover NOTE To avoid creating a fire hazard or producing harmful evaporative emissions do not clean filter in gasoline or other flammable solvent 3 Wash the filter in soap and water 4 Allow filter to dry 5 Replace parts INSPECT MUFFLER AND SPARK ARRESTING SCREEN WARNING The muffler on this prod uct contains chemicals known to the State of California to cause cancer As your unit is used carbon deposits build up on the muffler and spark arresting screen and must be removed to avoid creating a fire haz ard or affecting engine performance For normal homeowner use the muffler and spark arresting screen will not require any service After 50 hours of use we recom mend that your muffler be serviced or re placed by an authorized service dealer REPLACE SPARK PLUG Replace the spark plug each year to ensure the engine starts easier and runs better Set spark plug gap at 0 025 inch 0 6 mm Igni tion timing is fixed and nonadjustable NOTE This spark ignition sys
20. dust cup with the hole in the side of the gearbox by rotating the dust cup 2 Insert a small screwdriver into aligned holes This will keep the shaft from turning while removing and installing trimmer head 3 While holding the screwdriver in position remove trimmer head by turning clockwise 14 4 Thread replacement trimmer head onto the shaft by turning counterclockwise Tighten until secure 5 Remove the screwdriver CARBURETOR IDLE SPEED ADJUSTMENT WARNING Keep others away when making idle speed adjustments The trimmer head blade or any optional attachment will be spinning during most of this procedure Wear your protective equipment and observe all safe ty precautions After making adjustments the trimmer head blade or any optional attachment must not move spin at idle speed The carburetor has been carefully set at the factory Adjustments may be necessary if you notice any of the following conditions e Engine will not idle when the throttle is released e The trimmer head blade or optional attachment moves spins at idle Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object Hold the unit by hand while running and making ad justments Keep all parts of your body away from the cutting attachment and muffler To adjust idle speed Allow engine to idle Adjust speed until engine runs without trimmer head blade or optional attach
21. e bent warped cracked broken or damaged in any other way Install required shield properly before using the unit Use the metal shield for all metal blade use Only use brushcutter attachments that provide a metal shield with proboscis nose Proboscis Use only specified blade and make sure itis properly installed and securely fastened Cut from your right to your left Always use the handlebar and a properly adjusted shoulder strap with blade see ASSEMBLY instructions in brushcutter attachment instruction manual CULTIVATOR SAFETY A WARNING Rotating tines can cause serious injury Keep away from rotating tines Stop the engine and disconnect the spark plug before unclogging tines or making repairs AX WARNING Inspect the area to be cultivated before starting the unit Remove all debris and hard and sharp objects such as rocks vines branches rope string etc e Avoid heavy contact with solid objects that might stop the tines If heavy contact occurs stop the engine and inspect the unit for damage Never operate the cultivator without the tine cover in place and properly secured Keep the tines and guard clear of debris After striking a foreign object stop the engine disconnect the spark plug and inspect the cultivator for damage Repair before restarting Disconnect attachment from the drive engine before cleaning the tines with a hose and water to remove any build up Oil the tines to prevent
22. e on your small off road engine but Poulan PRO cannot deny warranty solely for the lack of receipts or for your failure to en sure the performance of all scheduled main tenance As the small off road engine owner you should be aware that Poulan PRO may deny you warranty coverage if your small off road engine or a part of it has failed due to 17 abuse neglect improper maintenance un approved modifications or the use of parts not made or approved by the original equip ment manufacturer You are responsible for presenting your small off road engine to an Poulan PRO authorized repair center as soon as a problem exists Warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If you have any questions regarding your warranty rights and responsi bilities you should contact your nearest autho rized service center call Poulan PRO at 1 800 554 6723 or send e mail correspon dence to emission warranty HCOP emission com WARRANTY COMMENCE MENT DATE The warranty period begins on the date the small off road engine is pur chased LENGTH OF COVERAGE This warranty shall be for a period of two years from the initial date of purchase or until the end of the product warranty whichever is lon ger WHAT IS COVERED REPAIR OR RE PLACEMENT OF PARTS Repair or re placement of any warranted part will be performed at no charge to the owner at an ap proved Poulan PRO servicing center If you have any
23. engine disconnect spark plug and inspect the snowthrower for damage and repair if necessary before restarting unit Never operate the snowthrower near glass enclosures automobiles and trucks Never attempt to use the snowthrower ona roof Never operate the snowthrower near window wells dropoffs etc Never discharge snow onto public roads or near moving traffic Clear snow from slopes by going up and down never across Use caution when changing directions Never clear snow from steep slopes Let snowthrower run for a few minutes after clearing snow so moving parts do not freeze Look behind and use care when backing up Exercise caution to avoid slipping or falling especially when operating in reverse Know how to stop quickly ASSEMBLY 2 Remove shipping protector from coupler A WARNING If received assembled 3 Remove the shaft cap from the trimmer at repeat all steps to ensure your unit is properly tachment if present assembled and all fasteners are secure 4 Position locking release button of attach Examine parts for damage Do not use dam ment into guide recess of coupler aged parts 5 Push the attachment into the coupler until NOTE If you need assistance or find parts missing or damaged call 1 800 554 6723 It is normal for the fuel filter to rattle in the empty fuel tank Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer INSTALLI
24. essage la beled IMPORTANT regarding the use of ga sohol in your engine Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage Add stabilizer to the gasoline in the fuel tank or fuel storage container Follow the mix instructions found on stabilizer container Run engine at least 5 minutes after adding stabilizer HELPFUL TIP During storage of your gas oil mixture the oil will sepa rate from the gas We recommend that you shake the gas can weekly to insure proper blending of the gas and oil ENGINE Remove spark plug and pour 1 teaspoon of 40 1 2 cycle engine oil air cooled through the spark plug opening Slowly pull the starter rope 8 to 10 times to distribute oil Replace spark plug with new one of recom mended type and heat range Clean air filter Check entire unit for loose screws nuts and bolts Replace any damaged broken or worn parts At the beginning of the next season use only fresh fuel having the proper gasoline to oil ratio OTHER e Do not store gasoline from one season to another e Replace your gasoline can if it starts to rust 15 TROUBLESHOOTING TABLE A WARNING Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit carburetor 5 Carburetor requires adjustment TROUBLE CAUSE REMEDY Engine will not 1 Eng
25. formance and mini mum line wear by not crowding the line into the cutting area The right and wrong ways are shown below Tip of the line does the cutting Line crowded into work area Right The line will easily remove grass and weeds from around walls fences trees and flower beds but it also can cut the tender bark of trees or shrubs and scar fences For trimming or scalping use less than full throttle to increase line life and decrease head wear especially e During light duty cutting e Near objects around which the line can wrap such as small posts trees or fence wire For mowing or sweeping use full throttle for a good clean job TRIMMING Hold the bottom of the trimmer head about 3 inches 8 cm above the ground and at an angle Allow only the tip of the line to make contact Do not force trimmer line into work area Trimming above ground 12 SCALPING The scalping technique removes unwanted vegetation down to the ground Hold the bottom of the trimmer head about 3 in 8 cm above the ground and at an angle Allow the tip of the line to strike the ground around trees posts monuments etc This technique in creases line wear Scalping MOWING Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach In the mowing position keep the line parallel to the ground Avoid pressing the head into the ground as this can scalp the ground and damage the tool Mowi
26. h can hurt people or animals break glass or cause other damage Never run unit without the proper equipment attached When using your unit as a blower always install blower tubes Check air intake opening blower tubes or vacuum tubes frequently always with engine stopped and spark plug disconnected Keep vents and discharge tubes free of debris which can accumulate and restrict proper air flow Never place any object in air intake opening as this could restrict proper air flow and cause damage to the unit Never use for spreading chemicals fertilizers or other substances which may contain toxic materials To avoid spreading fire do not use near leaf or brush fires fireplaces barbecue pits ashtrays etc BRUSHCUTTER SAFETY A DANGER Blade can thrust violently away from material it does not cut Blade thrust can cause amputation of arms or legs A WARNING Do not use trimmer head as a fastening device for the blade WE WARNING The blade continues to spin after the trigger is released or engine is turned off The coasting blade can throw ob jects or seriously cut you if accidentally touched Stop the blade by contacting the left hand side of the coasting blade with material already cut WARNING Inspect the area to be cut before each use Remove objects rocks broken glass nails wire etc which can be thrown or become entangled in the blade or trimmer line Throw away and replace blades that ar
27. he law For normal homeowner use the muffler and spark arrest ing screen will not require any service After 50 hours of use we recommend that your muffler be serviced or replaced by your autho rized service dealer LINE TRIMMER SAFETY WARNING Inspect the area before each use Remove objects rocks broken glass nails wire etc which can be thrown by or become entangled in line Hard objects can damage the trimmer head and be thrown causing serious injury e Use only for trimming scalping mowing and sweeping Do not use for edging pruning or hedge trimming e Cut from your left to your right Cutting on right side of the shield will throw debris away from the operator ADDITIONAL SAFETY RULES FOR OPTIONAL ATTACHMENTS WARNING For each optional at tachment used read entire instruction manu al before use and follow all warnings and in structions in manual and on attachment WARNING Ensure handlebar is installed when using brushcutter attachment Attach handlebar above arrow on safety label on the upper shaft engine end of unit If your brushcutter attachment does not include a handlebar a handlebar accessory kit 530071451 is available from your autho rized service dealer Handlebar AT EDGER SAFETY WARNING Inspect the area to be edged before each use Remove objects rocks broken glass nails wire etc which can be thrown by the blade or can wrap around the shaft A WARNING
28. ine flooded 1 See Starting a Flooded Engine in start Operation Section 2 Fuel tank empty 2 Fill tank with correct fuel mixture 3 Spark plug not firing 3 Install new spark plug 4 Fuel not reaching 4 Check for dirty fuel filter replace Check for kinked or split fuel line repair or replace Contact an authorized service dealer muffler outlet screen Engine will 1 Carburetor requires 1 See Carburetor Idle Speed Adjustment not idle adjustment in Service and Adjustments Section properly 2 Crankshaft seals worn 2 Contact an authorized service dealer 3 Compression low 3 Contact an authorized service dealer Engine will not 1 Air filter dirty 1 Clean or replace air filter accelerate 2 Spark plug fouled 2 Clean or replace plug lacks power and regap or dies under 3 Carburetor requires 3 Contact an authorized service dealer a load adjustment 4 Carbon build up on 4 Contact an authorized service dealer Spark plug incorrect Carburetor requires adjustment 4 Carbon build up on muffler outlet screen On 5 Compression low 5 Contact an authorized service dealer Engine 1 Fuel mixture incorrect 1 Empty fuel tank and refill with smokes correct fuel mixture excessively 2 Air filter dirty 2 Clean or replace air filter 3 Carburetor requires 3 Contact an authorized service dealer adjustment Engine runs 1 Fuel mixture incorrect 1 See
29. into slot as shown 3 Pivot shield until bolt passes through hole in bracket 4 Securely tighten wing nut onto bolt Wing Nut Bracket Shield ADJUSTING THE HANDLE A WARNING When adjusting the han dle be sure it remains above the safety label and below the mark or arrow on the shaft 1 Loosen wing nut on handle 2 Rotate the handle on the shaft to an up right position retighten wing nut OPERATION KNOW YOUR UNIT READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments Save this manual for future reference Trimmer Head Line Limiter Blade ON STOP Switch ON STOP SWITCH The ON STOP switch is located on the trigger handle and is used to stop the engine To stop the engine push and release the engine ON STOP switch Coupler PRIMER BULB The PRIMER BULB removes air from the car buretor and fuel lines and fills them with fuel This allows you to start the engine with fewer pulls on the starter rope Activate the primer bulb by pressing it and allowing it to return to its original form START LEVER The START LEVER helps to supply fuel to the engine to aid in starting Activate the starting system by moving the start lever to the START position DO NOT squeeze the throttle trigger until the engine has started and runs After the BEFORE STARTING
30. ment moving or spinning idle too fast or stalling idle speed too slow Turn idle speed screw clockwise to increase engine speed if engine stalls or dies Turn idle speed screw counterclockwise to decrease engine speed if trimmer head blade or optional attachment moves or spins at idle WARNING Recheck the idle speed after each adjustment The trimmer head blade or optional attachment must not move or spin at idle speed to avoid serious injury to the operator or others If you require further assistance or are unsure about performing this procedure contact an authorized service dealer or call 1 800 554 6723 STORAGE WARNING Perform the following steps after each use Allow engine to cool before storing or trans porting Store unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters electric motors or switches furnaces etc Store unit with all guards in place Position unit so that any sharp object cannot acci dentally cause injury Store unit and fuel well out of the reach of children SEASONAL STORAGE Prepare unit for storage at end of season or if it will not be used for 30 days or more If your unit is to be stored for a period of time e Clean the entire unit before lengthy storage e Store in a clean dry area e Lightly oil external metal surfaces FUEL SYSTEM Under FUELING ENGINE in the OPERA TION section of this manual see m
31. mes 3 Move the start lever to the START position Primer Bulb 10 4 Pull starter rope handle sharply until en gine starts and runs 5 Allow unit to run for 10 15 seconds then fully squeeze the throttle trigger to disen gage the starting system STARTING A WARM ENGINE 1 Squeeze and hold the throttle trigger Keep throttle trigger fully squeezed until engine runs smoothly 2 Pull starter rope sharply while squeezing throttle trigger until engine runs NOTE Normally the warm starting proce dure can be used within 5 10 minutes after the unit is turned off If the unit sits for more than 10 minutes without being ran it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit STARTING A FLOODED ENGINE Flooded engines can be started by placing the start lever to the RUN position Fully squeeze throttle trigger Pull the starter han dle repeatedly while squeezing throttle trigger until engine starts and runs This could re quire pulling the starter handle many times depending on how badly the unit is flooded If the unit still doesn t start refer to TROUBLESHOOTING TABLE or call 1 800 554 6723 OPERATING THE COUPLER This model is equipped with a coupler which enables optional attachments to be installed The optional attachments are MODEL Edger eo RE eeee PP1000E Cultivator PP2000T Blower
32. mmer line will advance approximately 2 inches 5 cm each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle The most efficient line length is the maximum length allowed by the line limiter Always keep the shield in place when the tool is being oper ated To advance line e Operate the engine at full throttle e Hold the trimmer head parallel to and above the grassy area e Tap the bottom of the trimmer head lightly on the ground one time Approximately 2 inches 5 cm of line will be advanced with each tap Always tap the trimmer head on a grassy area Tapping on surfaces such as concrete or as phalt can cause excessive wear to the trimmer head If the line is worn down to 2 inches 5 cm or less more than one tap will be required to ob tain the most efficient line length WARNING Use only 0 095 2 4 mm diameter line Other sizes of line will not advance properly and can cause serious injury Do not use other materials such as wire string rope etc Wire can break off dur ing cutting and become a dangerous missile that can cause serious injury CUTTING METHODS WARNING Use minimum speed and do not crowd the line when cutting around hard objects rock gravel fence posts etc which can damage the trimmer head become entangled in the line or be thrown causing a serious hazard e The tip of the line does the cutting You will achieve the best per
33. ng SWEEPING The fanning action of the rotat ing line can be used to blow away loose debris from an area Keep the line parallel to and above the area surface and swing the tool from side to side Sweeping MAINTENANCE WARNING Disconnect the spark plug before performing maintenance except for carburetor adjustments HELPFUL TIP IMPORTANT Have all repairs other than the rec ommended maintenance described in the instruction manual performed by an authorized service dealer If any dealer other than an authorized service dealer performs work on the product Poulan PRO may not pay for repairs under warranty It is your re sponsibility to maintain and perform general maintenance CHECK FOR LOOSE FASTENERS AND PARTS Spark Plug Boot Air Filter Housing Screws Assist Handle Screw Debris Shield CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for re placement of damaged or worn parts ON STOP Switch Ensure ON STOP switch functions properly by pushing and releasing the switch Make sure engine stops Wait 5 seconds before attempting to restart unit to allow switch to reset Restart engine and continue Fuel Tank Discontinue use of unit if fuel tank shows signs of damage or leaks e Debris Shield Discontinue use of unit if debris shield is damaged INSPECT AND CLEAN UNIT AND DE CALS e After each use inspect complete unit for loose or damaged parts Clean the unit and
34. questions regarding your warranty rights and responsibilities you should contact your nearest authorized service center call Poulan PRO at 1 800 554 6723 or send e mail correspondence to emission warranty HCOP emission com WARRANTY PE RIOD Any warranted part which is not scheduled for replacement as required main tenance or which is scheduled only for regu lar inspection to the effect of repair or replace as necessary shall be warranted for 2 years Any warranted part which is scheduled for re placement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part DIAGNOSIS The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is de fective if the diagnostic work is performed at an approved Poulan PRO servicing center CONSEQUENTIAL DAMAGES Poulan PRO may be liable for damages to other en gine components caused by the failure of a warranted part still under warranty WHAT IS NOT COVERED All failures caused by abuse neglect or improper maintenance are not covered ADD ON OR MODIFIED PARTS The use of add on or modified parts can be grounds for disallowing a warranty claim Poulan PRO is not liable to cover failures of warranted parts caused by the use of add on or modified parts HOW TO FILE A CLAIM If you have any questions regarding your warran ty rights and responsibilities you should contact
35. rn the product to an authorized service dealer Should you have any unanswered questions concerning this warranty please contact Poulan PRO a division of Husqvarna Consumer Outdoor Products N A Inc 7349 Statesville Road Charlotte NC 28269 1 800 554 6723 In Canada contact Poulan PRO 850 Matheson Blvd West Mississauga Ontario L5V 0B4 Giving the model number serial number and date of purchase of your product and the name and address of the authorized dealer from whom it was purchased THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTH ER RIGHTS WHICH VARY FROM STATE TO STATE NO CLAIMS FOR CONSEQUENTIAL OR OTHER DAMAGES WILL BE ALLOWED AND THERE ARE NO OTHER EXPRESS WARRANTIES EXCEPT THOSE EX PRESSLY STIPULATED HEREIN SOME STATES DO NOT ALLOW LIMITA TIONS ON HOW LONG AN IMPLIED WAR RANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSE QUENTIAL DAMAGES SO THE ABOVE LIM ITATIONS OR EXCLUSION MAY NOT APPLY TO YOU This is a limited warranty within the meaning of that term as defined in the Magnuson Moss Act of 1975 The policy of Poulan PRO is to continuously improve its products Therefore Poulan PRO reserves the right to change modify or dis continue models designs specifications and accessories of all products at any time without notice or obligation to any purchaser U S EPA CALIFORNIA ENVIRONMENT CANADA EMISSION CONTROL WARRANTY STATEMENT YOUR WARR
36. tem complies with the Canadian standard ICES 002 1 Twist then pull off spark plug boot 2 Remove spark plug from cylinder and discard 3 Replace with Champion RCJ 6Y spark plug and tighten securely with a 3 4 inch 19 mm socket wrench 4 Reinstall the spark plug boot SERVICE AND ADJUSTMENTS REPLACING THE LINE 1 Press the tabs on the side of the trimmer head and remove cover and spool 2 Remove any remaining line 3 Clean dirt and debris from all parts Re place spool if it is worn or damaged 4 Replace with a pre wound spool or re place line using a 15 feet 4 5 meters length of 0 095 inch 2 4 mm diameter Poulan PRO brand line 5 When installing new line on an existing spool hold the spool as shown in the il lustration below 6 Bend the line at the midpoint and insert the bend into the slot in the center rim of the spool Ensure line snaps into position in the slot 7 With your finger between the lines wrap the lines evenly and firmly around the spool in a clockwise direction 8 Position the lines in the guide slots Guide Slot 9 Insert the ends of the lines through exit holes in the sides of the cover 10 Place the spool in the cover 11 Make sure the lines are not caught be tween the rim of the spool and the wall of the cover 12 Reinstall the spool and cover onto the trimmer head Push until cover snaps into place REPLACING THE CUTTING HEAD 1 Align hole in the
37. trouble Inspect thoroughly for loose nuts bolts or damage before continuing Contact an authorized service dealer for repair or replacement of affected parts as necessary SNOW THROWER SAFETY WARNING Keep hands and feet away from the rotor when starting or running the engine Never attempt to clear the rotor with the engine motor running Stop engine and disconnect spark plug before unclogging snow or debris from discharge chute or when adjusting vanes DS WARNING Never lean over dis charge chute Rocks or debris could be thrown into the eyes and face and cause seri ous injury or blindness A WARNING inspect the area where the unit is to be used Remove objects that could be thrown or damage the unit Some objects may be hidden by fallen snow be alert for the possibility e Direct material discharge away from glass enclosures automobiles etc Do not run engine at high speed while not removing snow Be attentive when using the snowthrower and stay alert for holes in the terrain and other hidden hazards Make sure the rotor will spin freely before attaching the snowthrower to the powerhead If the rotor will not rotate freely due to frozen ice thaw the unit before thoroughly before attempting to operate under power Keep the rotor clear of debris Do not throw snow near other people The snow thrower could propel small objects at high speed causing injury After striking a foreign object stop the
38. wrong hole could lead to seri ous injury or damage to the unit Locking Release Button in Primary Hole OPERATING INSTRUCTIONS It is recommended that the engine not be operated for longer than 1 minute at full throttle 11 OPERATING POSITION ALWAYS WEAR Hearing gt Protection Cut only from vour left to vour right g A WARNING Always wear eye protec tion Never lean over the trimmer head Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury When operating unit stand as shown and check for the following Wear eye protection and heavy clothing Hold trigger handle with your right hand and assit handle with left hand Keep unit below waist level Cut only from your left to your right to ensure debris is thrown away from you Without bending over keep line near and parallel to the ground and not crowded into material being cut Do not run the engine at a higher speed than necessary The cutting line will cut efficiently when the engine is run at less than full throttle At lower speeds there is less engine noise and vibration The cutting line will last longer and will be less likely to weld onto the spool Always release the throttle trigger and allow the engine to return to idle speed when not cutting To stop engine e Release the throttle trigger e Push and release the engine ON STOP switch TRIMMER LINE ADVANCE The tri
Download Pdf Manuals
Related Search