Pioneer DJM-300S Musical Instrument User Manual
Contents
1. PIONEER The Art of Entertainment DJ MIXER TABLE DE MIXAGE DJ M DJ M Operating Instructions Mode d emploi Fran ais Thank you for buying this Pioneer product Please read through these operating instructions so you will Know how to operate your model properly After you have finished reading the instructions put them away in a Safe place for future reference WARNING To PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION To PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE IMPORTANT NOTICE The serial number for this equipment is located on the rear panel Please write this serial number on your en closed warranty card and keep it in a secure area This is for your security CAUTION This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment To prevent electromagnetic interference with electric appliances such as radios and televisions use shielded cables and connectors for connections Nous vous remercions pour cet achat d un produit PIO NEER Nous vous demandons de lire soigneusement ce mode d emploi vous serez ainsi a m me de faire correctement fonctionner l appareil Apr s avoir bien lu le mode d emploi le ranger dans un endroit s r pour pouvoir s y r2. ously cold surroundings or when the room temperature rises sharply condensation may form inside and the unit may not be able to attain its full performance In cases like this allow the unit to stand for about an hour or raise the room temperature gradually Cleaning the unit e Use a polishing cloth to wipe off dust and dirt e When the surfaces are very dirty wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water and wrung out well then wipe again with a dry cloth Do not use furniture wax or cleaners e Never use thinners benzene insecticide sprays or other chemicals on or near this unit since these will corrode the surfaces 4 lt DRB1206 gt En Fr Emplacement Installer l appareil dans un endroit bien ventil a l abri d une temp rature ou d une humidit lev e Ne pas installer l appareil dans un endroit qui est expos aux rayons directs du soleil ni prees d appareils de chauf fage ou de radiateurs Une chaleur excessive peut affecter le coffret et les composants internes Une installation dans un environnement humide ou opussi reux peut provoquer un fonctionnement d fectueux ou un accident Eviter ga lement une installation pr s de cuisini res etc ou le lec teur peut tre expos de la fum e graisseuse de la va peur ou la chaleur Lorsque le lecteur est transport d un endroit froid dans une pi ce chaude ou si la temp rature de la pi ce augmente
3. 1 MM Output Lecteur Analogique2 Lecteur Analogique 1 CONNEXION Avant d effectuer les raccordement ou de les modifier veillez couper l alimentation et d brancher la fiche du cordon d alimentation 1 Connexion des appareils d entr e CDJ 500 CDJ 5001 Commercially available cord with mini plug no resistor By connecting to CDJ 500 CDJ 5001 the fader start function can be used Cordon commercialement disponible avec mini prise sans r sistor En raccordant le mat riel une installation CDJ 500 ou CDJ 5001 il est possible d utiliser la fonction d activation de la mise en veille Microphone Microphone Cassette deck etc Lecteur de cassette etc sortie MM Connecting audio cords Use cords with red and white pin plugs Connect the white plug to L and the red plug to R Be sure to insert completely Connexion des c bles audio Utilisez des c bles munis de fiches rouge et blanche Raccordez la fiche blanche sur L et la fiche rouge sur R Veillez les enfoncer compl tement White plug L CE blanche Red plug R De i Fiche rouge CONNECTIONS CONNEXION 2 Connection of Outputs 2 Connexion des sorties Headphone Casque d coute Stereo Amplifier Cassette Deck For recording Amplificateur Stereo Lecteur de Cassettes Pour les enregistrements O OO e OO A O02 2000 7 lt DRB1206 gt En Fr DENOMINATION ET FON
4. 1 CH 2 MASTER When the button of the desired source is pressed the sound of the channel selected will be output to the headphone terminal For CH 1 and CH 2 the sound before the channel fader is set will be output For MASTER the sound after the master control is set will be output Two sources can be selected simultaneously When MAS TER is pressed when CH 1 and CH 2 are selected simulta neously only MASTER will be selected When only one of the channels and M ASTER are selected simultaneously the one channel and MASTER will be selected Three sources cannot be selected simultaneously Relation between Monitor Select Switch and Headphone Output Monitor Select Switch Headphone Output ON OFF OFF CH1 L CH1 R OFF ON OFF CH2 L CH2 R OFF OFF ON MASTER L MASTER R ON ON OFF CHI L CH2 L CH1 L CH2 R ON OFF ON CH1 MONO MASTER MONO OFF ON ON CH2 MONO MASTER MONO Headphone Terminal PHONES DENOMINATION ET FONCTION DES ELEMENTS Commutateur du curseur de volume crois CH CROSS CH en cas de mixage partir du curseur de volume de canal Mixage direct Lorsque le bouton de d marrage de mise en veille est en position ON marche la mise en veille doit tre initialis e par la mise en veille de canal CROSS en cas de mixage partir du curseur de volume crois Mixage crois Lorsque le bouton de d marrage de mise en veille est en position ON
5. Customer Service Department at the above listed number for assistance PIONEER ELECTRONICS SERVICE INC CUSTOMER SUPPORT DIVISION P O BOX 1760 LONG BEACH CA 90801 1760 U S A For warranty information please see the Limited Warranty sheet included with your product Should this product require service in Canada please contact a Pioneer Canadian Authorized Dealer to locate the nearest Pioneer Authorized Service Company in Canada Alternatively please contact the Customer Service Department at the following address Pioneer Electronics of Canada Inc 300 Allstate Parkway Markham ON L3R OP2 905 479 4411 For warranty information please see the Limited Warranty sheet included with your product Si ce produit doit tre r par au Canada veuillez vous adresser un distributeur autoris e Pioneer au Canada pour obtenir le nom de la Soci t de Service Autoris e Pioneer le plus pr s de chez vous Ou encore veuillez vous communiquer avec le Service de Client le de Pioneer Pioneer lectroniques du Canada Inc 300 Allstate Parkway Markham ON L3R OP2 905 479 4411 Pour obtenir des renseignements sur la garantie veuillez vous reporter au feuillet sur la Garantie Limit e gui accompagne le produit Published by Pioneer Electronic Corporation Copyright 1996 Pioneer Electronic Corporation All rights reserved PIONEER ELECTRONIC CORPORATION 4 1 Meguro 1 Chome Meguro ku Tokyo 153 8654 J apan PIONEER NEW ME
6. ON marche En appuyant sur le bouton une seconde fois l indicateur s teint et l interrupteur de mode de mise en veille adopte sa position OFF arr t Quand le lecteur CD optionnel CDJ 500 ou CDJ 500I est connect l unit l aide du cordon mini fiche sans r sistance disponible dans le commerce le bouton ON OFF Marche Arr t est utilis pour un d marrage automatique du lecteur CD l aide des commandes de mise en veille de canal ou de mise en veille crois e NAME AND FUNCTION OF PARTS Cross Fader Switch CH CROSS CH Select when mixing sounds using the channel fader vol ume Direct mix When the fader start switch is ON fader should be started by the channel fader CROSS Select when mixing sounds using the cross fader Cross fader mix When the fader start switch is ON fader should be started by the cross fader Master Volume Level Adjustment MASTER LEVEL Used to adjust the level of the master output volume The signal mixing the CH1 and CH2 channel fader levels and microphone inputs will be output Headphone Monitor Section Monitor Level Knob MONITOR LEVEL Used for adjusting the headphone monitor volume Monitor Select Switch CH 1 CH 2 MASTER and indicators When pressed the indicator lights up and the fader start switch turns ON When pressed another time the indica tor goes off and the fader start switch turns off Used for selecting the headphone monitor sources CH
7. brusquement de la condensation risque de se former l int rieur du lecteur et il peut ne pas r aliser toutes ses performances Dans ce cas ne pas utiliser l appareil pen dant une heure environ ou augmenter progressivement la temp rature de la pi ce Entretien des surfaces ext rieurs Se servie d un linge polir or d un chiffon sec pour enle ver la poussi re ou les souillures Si les surfaces sont tr s sales les frotter avec un linge doux tremp dans un d tergent neutre dilu dans cing or six fois son volume d eau puis essuyer convenable ment les surfaces Ne pas utiliser de cire ou de produit pour meubles Ne jamais utiliser de diluant pour peinture de benzine ou d insecticide en atomiseur sur or proximit de l ap pareil car ses surfaces en seraient endommag es CHECKING ACCESSORIES CONTROLE DES ACCESSOIRES e Operating instructions FEATURES BPM Counter The auto BPM counter provided allows the tempo of songs to be checked visually This counter can be switched be tween real time and average 3 Band Equalizer amp Kill A 3 band equalizer corresponding to the HI MID and LOW channels The attenuation level also serves as a kill func tion which can decrease the level to 26 dB Peak Level Meter The peak level meter provided is equipped with 9 bit LED indicators for each channel This meter can be switched to display the master level or channel level Fader Start The CD player can b
8. et retirez le Retirez les deux vis ainsi que le panneau du curseur D tachez de l appareil l ensemble du curseur du volume et d branchez le connecteur Retirez les deux vis et remplacez la commande du curseur de volume par une nouvelle Fixez les vis le connecteur le panneau du curseur les vis et le bouton du curseur de volume dans l ordre inverse du d montage Ins rez fond le connecteur dans l ensemble du curseur de volume S il n est pas correctement ins r l appareil ne fonctionnera pas REMARQUES e Ne touchez pas les composants internes et ne glissez pas la main dans l appareil car vous risqueriez de l endom mager et de vous blesser Vous pouvez commander un nouveau curseur de volume e Veillez ce que les vis et les pi ces d tach es ne tombent T U76 aupr s de votre revendeur le plus proche ou d un pas dans l appareil centre de service apr s vente PIONEER 17 lt DRB1206 gt Fr SPECIFICATIONS Audio Section Input terminal Input level impedance CD A EA A 14 dBV 200 mV 22 kQ CINE E nee 14 dBV 200 mV 47 kQ PHONE ne re 54 dBV 2 mV 47 KQ ME E E 60 dBV 1 mV 3 kQ Output terminal Output level impedance MASTER OUT RCA ccisvsserrinercaniteniwaiadons 0 dBV 1V 1kQ PHOMES sr aus 4 dBV 0 63 V 150 Q Frequency characteristics COLINE aaraa Ea 20 Hz to 20 kHz ONCE en 20 Hz to 20 kHz nm 20 Hz to 20 kHz SN ratio CDN
9. excessive force and uneven surfaces may cause the product and cart combination to overtum 5 3 Y VENTILATION Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to POWER SOURCES This product should be operated only fromthe type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company LOCATION The appliance should be installed in a stable location NONUSE PERIODS The power cord of the appliance should be unplugged from the outlet when left un used for a long period of time GROUNDING OR POLARIZATION e If this productis equipped with a polarized altemating current line plug a plug having one blade wider than the other it will fitinto the outlet only one way This is asafety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the Safety
10. f rer ult rieurement ATTENTION AFIN DE PREVENIR TOURS RISQUES DE CHOC ELECTRIQUE OU DE DEBUT D ENCENDIE NE PAS EXPO SER CET APPAREIL A L HUMIDITE OU ALA PLUIE ATTENTION pour PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT REMARQUE IMPORTANTE Le num ro de s rie de cet appareil est inscrit sur le panneau arri re Veuillez noter ce num ro sur la carte de garantie qui accompagne le lecteur et conserver celle ci en lieu s r Cette pr caution peut tre utile en cas de vol IMPORTANT The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO PREVENT THE RISK OF ELECTRIC SHOCK DO NOT REM OVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance IMPORTANT SAFETY INSTRUCTIONS READ INSTRUCTIONS All the sa
11. it is too late this manufacturer and the Electronic Industries Association s Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise This list of sound levels is included for your protection Decibel Level Example 30 Quiet library soft whispers 40 Living room refrigerator bedroom away from traffic 50 Light traffic normal conversation quiet office 60 Air conditioner at 20 feet sewing machine 70 Vacuum cleaner hair dryer noisy restaurant 80 Average city traffic garbage disposals alarm clock at two feet THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE 90 Subway motorcycle truck traffic lawn mower 100 Garbage truck chain saw pneumatic drill 120 Rock band concert in front of speakers thunderclap 140 Gunshot blast jet plane 180 Rocket launching pad Information courtesy of the Deafness Research Foundation 3 lt DRB1206 gt En Fr CONTENTS CAUTIONS REGARDING HANDLING sssss a CHECKING ACCESSORIES csssscssssecnssecnssesnsseees 5 FEATURES ame ananas antenne 5 CONNECTIONS wisi sisiinsstisevsssticcustsavassiuanesasnessnnsscnanians 6 1 Connection of Input Equipment 6 2 Connection Of OUtpUts 7 NAME AND FUNCTION OF PARTS murs 8 MEASURING BPM ccsssscnssscnsssecnssecnssecnssesnsseens 12 USING THE FADER START FUNCTION 14 Starting the Cross Fader 1 eeeesseeeeeeeeesesseaeeeees 14 Starting the Chan
12. marche la mise en veille doit tre initialis e par la mise en veille crois e Ajustement du volume de la m lodie principale MASTER LEVEL Utilisation pour ajuster le niveau de volume de sortie de la m lodie principale Le signal de mixage des niveaux de mise en veille des canaux CH1 et CH2 et des entr es microphone sera interrompu Section de Commande du Microphone Bouton du niveau du moniteur MONITOR LEVEL Utilisation pour ajuster le volume du moniteur du casque d coute Bouton de S lection de Moniteur CH 1 CH 2 MASTER et indicateurs En appuyant sur ce bouton l indicateur s allume et l interrupteur de mode de mise en veille adopte sa posi tion ON marche En appuyant sur le bouton une seconde fois l indicateur s teint et l interrupteur de mode de mise en veille adopte sa position OFF arr t Servent la s lection de la source de commande du casque d coute CH 1 CH 2 MASTER Lorsque le bouton de la source d sir e est enfonc Le son du canal s lectionn sera transmis au terminal du casque d coute Pour CH 1 et CH 2 le son avant r glage de la mise en veille de canal sera transmis Pour MASTER le son apr s la commande principale sera transmis Il est possible de s lectionner deux sources simultan ment En appuyant sur MASTER quand CH 1 et CH 2 sont s lectionn s simultan ment seul MASTER sera retenu Quand un canal est s lectionn avec l un quelconque des canaux et MASTER
13. of the channel CH1 or CH2 connected to the player to be controlled Tum down the channel fader volume fully 4 Set the cue point of the player and set the player to standby at this cue point To start playing raise the cross fader volume at the desired time The cue point may be preset in the CD 5001 In this case there is no need for the player to standby at the cue point After playing starts if the fader control is completely re turned to the original position the player will return to the cue point and set into the standby state NOTE The player may start playing when the cord with mini plug without resistor is inserted disconnected or when the power of the main unit is turned off with the player power on UTILISATION DE LA FONCTION DE DEMARRAGE PAR CURSEUR DE VOLUME Fader Start D marrage par curseur de volume crois Placer la commande de mise en veille crois e sur CROSS Enclenchez le commutateur du curseur de volume CH 1 ou CH 2 du canal raccord au lecteur commander D placer la mise en veille crois e enti rement vers le c t oppos au canal activer Dans l exemple le lecteur CH 1 s active Exemple CROSS FADER D 4 Placez le lecteur au point de signal et mettez le lecteur en pause ce point de signal Pour d marrer la lecture d placer la commande de mise en veille crois e vers le canal activer au moment du d but de la lecture D marrage par c
14. purpose of the polarized plug e f this product is equipped with a three wire grounding type plug aplug having athird grounding pin it will only fitinto a grounding type power outlet This is asafety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the Safety purpose of the grounding type plug POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles andthe point where they exit from the product OUTDOOR ANTENNA GROUNDING If an outside antennaorcable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements forthe grounding electrode See Figure A LIGHTNING For added protection for this product duringalightning storm or when itis left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or ca
15. une prise de terre s re 4 CH1 CH2 Section de Commande d Entr e S lecteur d entr es INPUT SELECTOR Celui ci s lecte le son provenant d un des deux appareils connect s chaque CH utiliser CHI Commutation entre PHONO 1 LINE 1 et CD1 CH2 Commutation entre PHONO 2 LINE 2 et CD2 TRIM Utilis pour ajuster le niveau du signal d entr e Tournez vers la droite pour augmenter le niveau J usque 6 dB Tournez vers la gauche pour diminuer le signal J usque ce EQ Equaliseur HI Utilis pour ajuster les sons aigus Centre de la port e avec d clic Tournez vers la droite pour augmenter Tournez vers la gauche pour diminuer MID Utilis pour ajuster les sons de hauteur moyenne Centre de la port e avec d clic Tournez vers la droite pour augmenter Tournez vers la gauche pour diminuer LOW Utilis pour ajuster les sons graves Centre de la port e avec d clic Tournez vers la droite pour augmenter Tournez vers la gauche pour diminuer Affichage BPM R f rez vous a la page 12 Compteur e Affiche en chiffres la valeur BPM Bits Par Minute de l entr e source de CH1 et CH2 Affiche lorsque la mesure n a pas t possible pendant plus de 5 secondes ou quand l installation est en mode d arr t Affichage en mode r el la mise sous tension du syst me Bouton de s lection mode r el mode des moyennes et indicateur REAL AVERAGE A chaque pression du bouton le t moin lumineux d
16. 300 fader start play can be performed even when combined with CD 500 and CDJ 500I However back cue play can be performed only when combined with CDJ 5001 commercially avail able cord with mini plug no resistor CH2 B CDJ 5001 CH1 A CDJ 5001 CROSS FADER P En Cross Fader Start Play and Back Cue Play CHI A can be started just by moving the cross fader con trol from right to left during standby when CHI A is at the cue point Likewise CH2 B can also be started just by moving the cross fader control from left to right during standby when CH2 B is at the cue point When moved to the right end CH2 A will back cue re turn to the cue point 14 lt DRB1206 gt En Fr iyo volume crois H25 Cross fader control Commande par curseur de vo lume crois D marrage par curseur de volume En amplifant la commande de mise en veille mixte la pause du lecteur est d sactiv e et le morceau de musique commence imm diatement et automatiquement Le curseur de volume crois peut galement tre utilis pour effectuer ce d marrage par curseur de volume Le passage de s quences peut aussi avoir lieu en ramenant le curseur de volume sa position initiale ainsi le lecteur reviendra son point de signal signal de retour Le d marrage par curseur de volume du DJ M 300 peut tre utilis en connexion aux CDJ 500 et CDJ 500I N an moins l
17. CTION NAME AND FUNCTION OF PARTS DES ELEMENTS Control panel Panneau de commande 2 and shows the rear view while shows the front et O montrent la partie arri re alors que montre la view partie frontale SIGNAL 3 LINE PHONO GND DJ MIXER DJ M 300 CH 2 INPUT SELECTOR PHONO 2 LINE 2 TRIM INPUT SELECTOR PHONO 1 LINE 1 AUTO BPM COUNTER AUTO BPM COUNTER 888 888 O O 7 INPUT LEVEL cH1 Q MASTER LEVEL vty NY a a Mi 00 B 00 OdB MONITOR SELECTOR O FR N W B UI O NN N y P O5 N OF NW BU D N CH 1 CH 2 MASTER Ul CH 1 Q FADER START Q H 2 Jeg CROSS FADER b wv D 1 Microphone Input Control Section 1 Section de Commande d Entr e Microphone MIC Level Niveau MIC Used for adjusting the volume of the microphone Utilis pour ajuster le volume du microphone MIC EQ Microphone Equalizer MIC EQ Equaliseur Microphone Used for adjusting the sound quality of the microphone Sert au r glage de la qualit du son du microphone Flat at center click Centre de la port e avec d clic Emphasizes the high tone treble when rotated to the Intensifie les
18. Cette fonction n est utilisable que lorsqu un lecteur CD Pioneer des s ries CDJ 500 est connect Commande d Allocation Permet de r partir les entr es canaux et les sorties principales sur les couteurs de gauche et de droite et de les g rer Cela permet d activer des musiques des heures pr cises Connexions d entr e et de sortie am lior es Equip d un total de 7 entr es 2 entr s CD 2 entr es LINE ligne 2entr es PHONES casque pour MM seulement ainsi qu une entr e et 2 sorties microphone 5 lt DRB1206 gt En Fr CONNECTIONS Before making or changing the connections switch off the power switch and disconnect the power cord from the AC outlet 1 Connection of Input Equipment DAT etc DAT etc 60 To an AC wall socket Prise secteur murale Analog Player 2 MM Output sortie MM NOTE When connecting the analog players to PHONOI LINE I and PHONOZ2 LINE2 terminals set the input source selection switch on the rear panel to PHONO REMARQUE Lors de la connexion de lecteurs analogiques sur PHONO1 LINE1 et PHONO2 LINE2 placer le s lecteur de source d entr e du panneau arri re sur PHONO LINE PHONO When not using the analog player set the switch to LINE See page 9 En n utilisant pas de lecteurs analogiques placer ce s lecteur sur LINE Voir page 9 6 lt DRB1206 gt En Fr CDJ 500 CDJ 5001 Analog Player
19. DIA TECHNOLOGIES INC Headquarters 2265 East 220th Street Long Beach Califomia 90810 U S A TEL 310 952 2111 PIONEER ELECTRONICS OF CANADA INC Toronto Head Office 300 Allstate Parkway Markham Ontario L3R OP2 Canada TEL 905 479 4411 lt 98G00ZF0Z00 gt Printed in J apan lt DRB1206 B gt
20. En Fr For Canadian model This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Pour le modele Canadien Cet appareil numerique dela Classe B respecte toutes les exigences du Reglement sur le material brouilleur du Canada Information to User Alteration or modifications carried out without appropriate authorization may invalidate the user s right to operate the equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the d
21. a es rs ou 80 dB ONCE rer er re nn ene Oren ee ee 75 dB PO EEA A T 67 dB Total harmonic distortion rate CD LINE PHONO MIC PEIE EET E ET Below 0 05 In 3 Vrms output COS AR OE EE me eer E on T 70 dB Channel equalizer LOV e 12 dB 26 dB 70 Hz D cee eer tere eee 12 dB 26 dB 1 kHz a E 12 dB 26 dB 13 kHz Microphone equalizer ccccccceseeeeeeeees 12 dB 10 kHz 18 lt DRB1206 gt En Electrical Section Others Power supply voltage cccceeeeeeeeeeeeeeeeeees AC 120 V 60 Hz Power consumption Us 16 W Operating temperature 5 C to 35 C 419F to 95 F Operating AUMIQEE a en 5 to 85 External dimensions 308 W x 220 D x 107 4 H mm 12 1 8 W x 8 11 16 D x 4 1 4 H in LES 3 5 kg 7 15 12 07 Accessories e Operating INStructions 8 ms esters 1 NOTE Specifications and the design are subject to possible modi fications without notice due to improvements Published by Pioneer Electronic Corporation Copyright 1996 Pioneer Electronic Corporation All rights reserved FICHE TECHNIQUE Partie audio Prise d entr e Niveau d entr e imp dance D ns 14 dBV 200 mV 22 kQ ONE alec 14 dBV 200 mV 47 kQ PRON oraninin O 54 dBV 2 mV 47 KQ N OE 60 dBV 1 mV 3 KQ Prises de sortie Niveau de sortie imp dance MASTER OUT RCA eeen 0 dBV 1V 1kQ P ONESS a 4 dBV 0 63 V 150 Q Caract ristiques de fr quence SEL E E T T T 20 Hz 20 kHz PONS n
22. aigus lorsqu il est tourn vers la droite right Intensifie les basses lorsqu il est tourn vers la gauche Emphasizes the low tone bass when rotated to the left 8 lt DRB1206 gt En Fr NAME AND FUNCTION OF PARTS 2 Rear Panel Input Source Selection Switch Used for selecting the device connected to PHONO 1 LINE 1 and PHONO 2 LINE 2 input terminals PHONO Analog player MM output LINE Audio equipment whose output level is the line level NOTE Do not switch with the power ON When switched the master output will be muted 3 Ground Terminal SIGNAL GND Connects to the GND cord of the analog player This terminal is for only an analog player not for a safety ground 4 CH1 CH2 Input Control Section Input selection switch INPUT SELECTOR Selects which one of the two units connected to each CH to use CH1 Switches between PHONO 1 LINE 1 and CD1 CH2 Switches between PHONO 2 LINE 2 and CD2 TRIM Used for adjusting the level of the input signal The level increases when rotated to the right To 6 dB The level decreases when rotated to the left To c EQ Equalizer HI Used for adjusting the high tone Flat at center click Increases when rotated to the right Decreases when rotated to the left MID Used for adjusting the middle tone Flat at center click Increases when rotated to the right Decreases when rotated to the left LOW Used for adjusting the low tone Flat at center cli
23. ar exemple Display when BPM of CH1 126 and BPM of CH2 126 match Affichage lorsque le BPM du CHI 126 et le BPM du CH2 126 s accordent AUTO BPM COUNTER AUTO BPM COUNTER REAL AVERAGE Goes off S arr te 13 lt DRB1206 gt En Fr USING THE FADER START FUNC TION By connecting the optional CD players CDJ 500 and CDJ 5001 to the unit the player can be started using the chan nel fader or cross fader controls The commercially avail able cord with mini plug no resistor must be connected Channel fader controls Commande du curseur UTILISATION DE LA FONCTION DE DEMARRAGE PAR CURSEUR DE VOLUME Fader Start En connectant le lecteur CD optionnel CDJ 500 ou CD 5001 l unit le lecteur peut tre d marr l aide des commandes de mise en veille de canal ou de mise en veille crois e Le cordon mini fiche sans r sistance doit tre branch de volume de canal Fader start switches Commutateur de d marrage Cross fader switch Commutateur du curseur de par curseur de volume lt cH 1 Fader Start Play By increasing the mixer fader control the pause of the player will be released and the song starts immediately automatically The cross fader can also be used to per form fader start play By returning the fader to the origi nal position as the player will be returned to the cue point back cue sampler playing can also be performed DJ M
24. ate normally by following the operating instructions Adjust onlythose controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or damaged in any Way e When the product exhibits a distinct change in performance this indicates a need for service REPLACEMENT PARTS When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may resultin fire electric shock or other hazards SAFETY CHECK Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition WALL OR CEILING MOUNTING The product should not be mounted to a wall or ceiling HEAT The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat ANTENNA LEAD IN WIRE GROUND DISCHARGE UNIT NEC SECTION 810 20 GROUNDING CONDUC TORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE 2 lt DRB1206 gt
25. ble system This will prevent damage to the product due to lightning and power line surges POWER LINES An outside antenna system should not be located in the vicinity of overhead powerlines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal OVERLOADING Do not overload wall outlets extension cords orintegral convenience receptacles as this can result in a risk of fire or electric shock OBJ ECT ANDLIQUIDENTRY Never push objects of ELECTRIC SERVICE EQUIPMENT Fig A any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product SERVICING Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel DAMAGE REQUIRING SERVICE Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions e When the power supply cord or plug is damaged e If liquid has been spilled or objects have fallen into the product e Ifthe product has been exposed to rain or water e Ifthe product does not oper
26. ck Increases when rotated to the right Decreases when rotated to the left BPM Display Refer to Page 12 Counter e Displays the BPM of the source input to CH1 and CH2 dig itally Displays when BPM could not be measured for more than 5 seconds or when switched off Displays in real mode when the power is turned on Real mode average mode selection button and indicator Each time the button is pressed the display mode and in dicator light switch as follows REAL AVERAGE fr a When REAL is selected Displays the measured BPM value at real time The measurement error is greater than AVERAGE Blinks while measuring When AVERAGE is selected The display timing becomes slower but the display will be stabilized by the averaging process While measuring the previous value will remain dis played DENOMINATION ET FONCTION DES ELEMENTS 2 Interrupteur de S lection de la Source d Entr e du Panneau Arri re Sert a la s lection des terminaux d entr es raccord s a PHONO 1 LINE 1 et PHONO 2 LINE 2 PHONO Lecteur analogique sortie MM LINE Equipement audio dont le niveau de sortie est le niveau de ligne REMARQUE Ne pas mettre sous tension ON Lors de la mise sous tension la sortie principale est d sactiv e 3 Prise de terre SIGNAL GND Connexion au c ble de masse du lecteur analogue Cette prise est r serv e un lecteur analogique mais ne constitue pas
27. e started by increasing the level of the cross fader or channel fader which is selected using the cross fader switch This function can be used only when the Pioneer CD player CDJ 500 series is connected Allocation Monitor Enables channel inputs and master outputs to be divided into the left and right headphones and monitored As a result music can be joined accurately Enhanced Input Output Terminals Equipped with a total of 7 inputs 2 CD Inputs 2 LINE in puts 2 PHONO inputs for MM only and 1 microphone input and 2 outputs e Mode d emploi CARACTERISTIQUES PRINCI PALES Compteur BPM Le compteur auto BPM incorpor permet de v rifier visuel lement le tempo de la musique Ce compteur peut afficher des valeurs en temps r el ou des valeurs moyennes Egaliseur 3 bandes et suppression L galiseur a 3 bandes correspond aux canaux HI MID et LOW Le niveau d att nuation peut galement servir de fonction de suppression qui peut diminuer le niveau de 26 dB Mesure du niveau de pic sonore L indicateur de niveau maxi est quip d indicateurs LED de 9 bits pour chaque canal Cet indicateur peut tre programm pour indiquer le niveau principal ou le niveau du canal D marrage par curseur de volume Le lecteur CD peut tre d marr en augmentant le niveau du curseur de volume crois ou du curseur de canal ceuxci peuvent tre s lectionn s l aide du commutateur du curseur de volume crois
28. e unit and disconnect the connector Remove the two screws and replace the cross fader volume control with a new one Attach the screws connector slider panel screws and knob of the cross fader in the reverse order of the above Fully insert the connector into the cross fader assembly If itis not fully inserted the unit will not work correctly ONO NOTES e Do not touch the internal parts of the unit or put your hand inside the unit as this may cause injuries and dam age to the unit e Be careful not to drop removed parts and screws inside Order the cross fader assembly T U 76 from your nearest the unit dealer or PIONEER authorized service center 16 lt DRB1206 gt En DEPISTAGE DES PANNES Des erreurs de manipulation sont souvent prises pour une d faillance ou un mauvais fonctionnement En pr sence d une difficult apparente v rifier les points suivants Comme la difficult peut galement provenir d un autre l ment v rif r ceux ci ainsi que les autres appareils lectriques utilis s en m me temps Si le probl me ne peut pas tre r solu s adresser au centre de service ou au concessionnaire PIONEER le plus proche L alimentation lectrique Le c ble d alimentation n est pas branch Raccordez la prise d alimentation ne s enclenche pas Aucun son ou son trop La position de l interrupteur du s lecteur d en e S lectionnez l appare
29. ealer or an experienced radio TV technician for help Selecting fine audio equipment such as the unit you ve just purchased is only the start of your musical enjoyment Now it s time to consider how you can maximize the fun and excitement your equipment offers This manufacturer and the Electronic Industries Association s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level One that lets the sound come through loud and clear without annoying blaring or distortion and most importantly without affecting your sensitive hearing Sound can be deceiving Over time your hearing comfort level adapts to higher volumes of sound So what sounds normal can actually be loud and harmful to your hearing Guard against this by setting your equipment at a safe level BEFORE your hearing adapts To establish a safe level Start your volume control at a low setting Slowly increase the sound until you can hear it comfortably and clearly and without distortion Once you have established a comfortable sound level e Set the dial and leave it there Taking a minute to do this now will help to prevent hearing damage or loss in the future After all we want you listening for a lifetime We Want You Listening For A Lifetime Used wisely your new sound equipment will provide a lifetime of fun and enjoyment Since hearing damage from loud noise is often undetectable until
30. fety and operating instructions should be read before the product is operated RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference HEED WARNINGS All warnings on the product and in the operating instructions should be adhered to FOLLOW INSTRUCTIONS All operating and use instructions should be followed CLEANING Unplug this product from the wall outlet before cleaning The productshould be cleaned only with a polishing cloth or a soft dry cloth Never clean with furniture wax benzine insecticides or other volatile liquids since they may corrode the cabinet ATTACHMENTS Do not use attachments not recommended by the product manufactureras they may cause hazards WATER AND MOISTURE Do not use this product near water for example near a bathtub wash bowl kitchen sink orlaundry tub in awet basement or near a swimming pool and the like ACCESSORIES Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer CART A product and cart combination should be moved with care Quick stops
31. il en cours de lecture faible tr e est incorrecte partir du commutateur du s lecteur d entr e e Le cable de connexion n est pas raccord cor e Raccordez correctement rectement ou est d connect e La prise ou la fiche est sale e Nettoyez et raccordez e Le niveau d entr e est trop lev e Ajustez avec le bouton de r glage TRIM Le curseur de volume Placer la commande de mise en veille crois e Placer la commande de mise en veille crois e crois ne fonctionne pas sur CH sur CROSS La s lection de volume du Le commutateur de d marrage par curseur de Enclenchezle commutateur de d marrage par lecteur CD ne fonctionne volume est sur OFF curseur de volume pas eLa fiche de commande du lecteur l arri re Connecter les terminaux de contr le du lecteur n est pas raccord e CD et l unit muni du cordon mini fiche sans r sistance disponible dans le commerce Cette unit et le lecteur CD ne sont pas Connecter l aide d un cordon audio connect s par un cordon audio L appareil ne peut fonctionner correctement cause de l lectricit statique et des effets ext rieurs Remplacement de la commande du curseur de volume La structure de cet appareil permet le remplacement de son curseur de volume Proc dez de la mani re suivante D branchez la fiche d alimentation de l appareil au ni veau de la prise secteur Tirez sur le bouton du curseur de volume
32. l first be set to the master level display 7 Cross Fader Section Cross Fader Volume CROSS FADER Operates when the cross fader switch is at the CROSS Side Controls and outputs the CH1 and CH2 signals When the control is set to the left side the CH1 signal increases To 0 dB and the CH2 signal decreases To c When set to the right side the CH2 signal increases To 0 dB and the CH1 signal decreases To ce Fader Start Switch FADER START and indi cator Refer to Page 14 When pressed the indicator lights up and the fader start switch turns ON When pressed another time the indica tor goes off and the fader start switch goes off When the optional CD player CDJ 500 or CD 5001 is connected to the unit using the commercially available cord with mini plug no resistor this ON OFF switch is used to start automatic playing of the CD player using the channel fader or cross fader 10 lt DRB1206 gt En Fr DENOMINATION ET FONCTION DES ELEMENTS Curseur de volume de canal Afin d ajuster le volume de CH1 a CH2 Interrupteur d alimentation POWER Mise en MARCHE ARRET de cette unit Lorsque le mat riel est mis sous tension l unit est d sactiv e pendant environ 2 secondes afin de prot ger les unit s connect es 6 Section de Commande Principale Indicateur de niveau L interrupteur de s lection de mode d affichage de l indicateur de niveau permet l affichage de deux niveaux Lorsque l i
33. nd CH2 Rotate the TRIM control and adjust the input level so that the display lights up without the input level meter swinging to the other end Select the BPM display mode using the real mode average mode selection button e Each time the button is pressed the display mode and indicator lit switch as follows REAL t AVERAGE off _ y e Real display Displays the measured BPM value at real time The measurement error is greater than AVERAGE e Average display The display timing becomes slower but the display will be stabilized by the averaging process While measuring the previous value will remain dis played e Off Both REAL and AVERAGE go off The BPM coun ter displays and BPM is not displayed 12 lt DRB1206 gt En Fr MESURE DU BPM Compteur auto BPM AUTO BPM COUNTER Mesure automatiquement la valeur BPM Bits Par Minute Facteur d indication de la vitesse de la musique du morceau et l affiche de mani re num rique 1 Il ne s agit pas uniquement d un comptage des battements des sons graves mais galement d un calcul par ordina teur du BPM d origine de la m lodie dont les Disc ockeys ont besoin et d un affichage digital Ceci permet ainsi d appr cier le BPM non plus uniquement l oreille comme par le pass mais galement visuelle ment ce qui offre la possibilit de mixer plus rapidement et plus ais ment des m lodies de tempos diff rents Le mode de mesure consis
34. ndicateur de mode d affichage de niveau est d sactiv le niveau principal est affich Lorsqu il est allum les niveaux d entr e de CH1 et CH2 sont affich s Le niveau maxi est maintenu pendant 2 secondes La port e de l affichage s tend de 20 dB 6 dB Bouton de S lection de Mode d Affichage de l Indicateur de Niveau et Indicateur Servent l activation du mode d affichage de l indicateur de niveau chaque pression du bouton le mode alterne entre l affichage du niveau principal et l affichage du niveau d entr e CH1 CH2 l indicateur de niveau d entr e INPUT LEVEL reste allum pendant l affichage du niveau d entr e En mettant l installation sous tension le mode d affichage du niveau principal est automatiquement activ 7 Section de mise en veille crois e Curseur de volume crois CROSS FADER Activ e lorsque le bouton de mise en veille crois e est plac du c t CROSS Contr le et permet la sortie de signaux CH1 et CH2 Quand la commande est plac e sur la gauche le signal CH1 augmente jusqu OdB et le signal CH2 d cro t jusqu co Quand la commande est positionn e droite le signal CH2 augmente J usqu a O dB et le signal CH1 diminue J usqu a co Interrupteur d Activation Mise en Veille FADER START et indicateur R f rez vous a la page 14 En appuyant sur ce bouton l indicateur s allume et l interrupteur de mode de mise en veille adopte sa posi tion
35. nel fader cceceeeeeeeeeeeeeeeeeees 14 TROUBLESHOOTING ssccsssccnssscnsssensssecnssesnsseses 16 SPECIFICATIONS scsitcctivescaccccacnscscssticsciananantecncssnnis CAUTIONS REGARDING HANDLING TABLE DES MATIERES PRECAUTIONS CONCERNANT LA MANIPULATION 4 CONTROLE DES ACCESSOIRES cssscsnscenssenssees 5 CARACTERISTIQUES PRINCIPALES sm 5 CONNEXION a a nain 6 1 Connexion des appareils d entr e ereen 6 2 Connexion des sorties DENOMINATION ET FONCTION DES ELEMENTS 8 MESURE DU BPM aan anneau 12 UTILISATION DE LA FONCTION DE DEMARRAGE PAR CURSEUR DE VOLUME Fader Start 14 D marrage par curseur de volume crois 14 D marrage par curseur de volume de canal 14 DEPISTAGE DES PANNES cssccssscnsscessecnssenseens 17 FICHE TECHNIQUE nssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn PRECAUTIONS CONCERNANT LA MANIPULATION Install the unit in a well ventilated location where it will not be exposed to high temperatures or humidity Do not install the unit in a location which is exposed to direct rays of the sun or near stoves or radiators Exces sive heat can adversely affect the cabinet and internal com ponents Installation of the unit in a damp or dusty envi ronment may also result in a malfunction or accident Avoid Installation near cookers etc where the unit may be ex posed to oily smoke steam or heat When this unit is brought into a warm room from previ
36. o 20 Hz 20 kHz A D a a TT 20 Hz 20 kHz Rapport SN COINS a EE 80 dB PHONO nn 75 dB MI aatsuatsee Ge otiinectnb a nerssdeusienstiss 67 dB Degr total de distorsion harmonique CD LINE PHONO MIC EEE E A TE Inf rieur 0 05 Sortie 3 Vrms COS OR E A A E A OE E wu Masten 70 dB Egaliseur de canal LONN See er te een enter 12 dB 26 dB 70 Hz D E 12 dB 26 dB 1 kHz in ee cere err 12 dB 26 dB 13 kHz Egaliseur de microphone 12 dB 10 kHz Partie lectrique Autres Tension d alimentation Ro AC 120 V 60Hz Consommation de courant 16 W Temp rature de fonctionnement 668 5 C 35 C Degr d humidit en fonctionnement 5 85 Dimensions ext rieures 308 L x 220 P x 107 4 H mm OS E E T 3 5 kg Accessoires e Mode d emplois a a eee 1 REMARQUE Les sp cifications et le design peuvent tre modifi s sans autre avis pour y apporter des am liorations Publication de Pioneer Electronic Corporation 1996 Pioneer Electronic Corporation Tous droits de reproduction et de traduction r serv s 19 lt DRB1206 gt Fr Should this product require service in the U S A and you wish to locate the nearest Pioneer Author ized Independent Service Company or if you wish to purchase replacement parts operating instruc tions service manuals or accessories please call the number shown below 800 872 4159 Please do not ship your product to Pioneer without first calling the
37. out repair work The power does not tum on The power cord is not connected e Connect to the power outlet No sound or soft sound e The position of the input selector switch is wrong Select the device currently playing with the input selector switch e The connection cord is not connected properly or dis e Connect properly connected e The terminal or plug is dirty e Clean and connect Noses e The input level is too high e Adjust with the trim knob e Set the cross fader switch to CH e Set the cross fader switch to CROSS The fader of the CD player The fader start switch is off e Turn on the fader start switch does not start e The player control terminal at the rear is not con Connect the control terminals of the nected CD player and the unit with the com mercially available cord with mini plug no resistor e This unit and the CD player are not connected by Connect by an audio cord an audio cord Abnormal functioning of this unit may be caused by static electricity or other external interference To restore normal opera tion turn the power off and then on again Replacement of Cross Fader Volume Control The unit has a structure which allows its cross fader to be replaced Replace as follows Disconnect the power plug of the unit from the outlet Pull up the knob of the cross fader and remove Remove the two screws and remove the slider panel Remove the cross fader assembly from th
38. s lectionn s simultan ment le dernier canal s lectionn et MASTER seront retenus Trois sources ne peuvent pas tre s lectionn es simultan ment Relation entre Bouton de S lection de Moniteur et Sortie Casque d coute Bouton de S lection de Moniteur Sortie Casque d coute CH 1 CH 2 MASTER R ON OFF OFF CH1 L CH1 R OFF ON OFF CH2 L CH2 R OFF OFF ON MASTER L MASTER R ON ON OFF ON OFF ON OFF ON ON CHI L CH2 L CH1 L CH2 R CH1 MONO MASTER MONO CH2 MONO MASTER MONO 9 Prise pour casque d coute PHONES 11 lt DRB1206 gt En Fr MEASURING BPM Auto BPM Counter AUTO BPM COUNTER Automatically measures the BPM Beats per minute Fac tor indicating music speed of the song and displays it dig itally 1 It not only counts the beat of bass sounds but also calcu lates using a computer the original BPM of the song re quired by DJ s and displays it digitally This allows the BPM to now be checked not only with the ear as done previously but also visually thereby enabling songs with different tempos to be mixed more quickly and simply The measurement mode consists of the real mode which displays the data in real time and the average mode which displays the average value calculated 1 Able to calculate the BPM of most songs but not of some e g acapella ad lib etc Example Displays the BPM of the song input to CH1 a
39. te en un mode r el qui affiche les donn es en temps r el et un mode moyenne qui affiche la valeur moyenne calcul e 1 Capacit calculer le BPM de la plupart des m lodies l exception de certaines comme par ex a capella ad lib etc Exemple Affiche la valeur BPM de l entr e du morceau vers CH1 et CH2 Faire toumer la commande TRIM et ajuster le niveau d entr e de sorte que l afficheur s allume sans que l indicateur de niveau ne bascule vers l autre c t S lectionner le mode d affichage BPM en utilisant le bouton de s lection mode r el mode des moyennes e A chaque pression du bouton le t moin lumineux du mode d affichage et de l indicateur suit le cheminement suivant en p MOYENNE d sactivation a e Mode r el Affiche la valeur BPM mesur e en temps r el L erreur de mesure est sup rieure MOYENNE Affichage de moyenne La s quence d affichage sera plus lente mais l affichage sera stabilis par le calcul de la valeur moyenne Durant la mesure la valeur pr c dente demeure affich e e D sactivation REEL et MOYENNE s arr tent Le compteur BPM Bits Par Minute indique et la valeur BPM n est pas affich e USING THE EFFECT FUNCTION UTILISATION DE LA FONCTION D EFFET Adjust the play tempo speed using the R gler le tempo de lecture la vitesse en player of CH1 and CH2 Eg CD player utilisant le lecteur CH1 et CH2 Lecteur CD p
40. u mode d affichage et de l indicateur suit le cheminement suivant nen p MOYENNE d sactivation a Lorsque REAL est s lectionn Affiche la valeur BPM mesur e en temps r el L erreur de mesure est sup rieure MOYENNE Clignote lors de la mesure Lorsque AVERAGE est s lectionn La s quence d affichage sera plus lente mais l affichage sera stabilis par le calcul de la valeur moyenne Durant la mesure la valeur pr c dente demeure affich e 9 lt DRB1206 gt En Fr NAME AND FUNCTION OF PARTS Channel Fader Volume Used for adjusting the volume of CHI to CH2 5 Power Supply Switch POWER Turns ON OFF the power of this unit When the power is turned ON the unit will be muted for about 2 seconds to protect the connected units 6 Master Control Section Level meter The level meter display mode selection switch enables two levels to be displayed When the level meter display mode indicator is off the master level is displayed When It is lit the CH1 and CH2 input levels are displayed The peak level is held for 2 seconds The display range is 20 dB to 6 dB Level Meter Display Mode Selection Button and Indicator Used for switching the level meter display mode Each time the button is pressed the mode will be switched between the master level display and input level display CH1 CH2 The INPUT LEVEL indicator is lit during the input level display When the power is turned on the mode wil
41. urseur de volume de canal Placer la commande de mise en veille crois e sur CH Activer la mise en veille de canal CH1 ou CH2 connect e contr ler R duire au minimum le volume de mise en veille de canal 4 Placez le lecteur au point de signal et mettez le lecteur en pause ce point de signal Pour d marrer la lecture augmentez le cur seur de volume crois au moment o le d marrage est d sir Le point de signal peut tre pr enregistr pour les CD 5001 Dans ce cas il n est pas n cessaire de mettre le lecteur en pause ce point de signal Apr s le d marrage de la lecture le lecteur retournera son point de signal et se placera en pause si la com mande de volume est ramen e dans sa position initiale REMARQUE Le lecteur peut d marrer lorsque le cordon mini fiche sans r sistance est raccord d connect ou lorsque l unit principale est mise hors tension alors que le lecteur reste sous tension 15 lt DRB1206 gt En Fr TROUBLESHOOTING Incorrect operations are often mistaken for trouble and malfunctions If you think that there is something wrong with this component check the points below Sometimes the trouble may lie in another component Investigate the other components and electrical appliances being used If the trouble cannot be rectified even after exercising the checks listed below ask your nearest PIONEER authorized service center or your dealer to carry
42. utilisation du signal de retour n est possible qu en connexion aux CDJ 5001I Cordon mini fiche sans r sistance disponible dans le CH1 A commerce CH2 B CDJ 5001 CDJ 5001 D marrage par curseur de volume crois et signal de retour Le lecteur CH1 A peut tre d marr en d pla ant sim plement la commande du curseur de volume crois de la droite vers la gauche au cours d une pause et lorsque CH1 A se trouve au point de signal Semblablement CH2 B peut galement tre d marr en d pla ant la commande du curseur de volume crois de la gauche vers la droite au cours d une pause et lorsque CH2 B se trouve au point de signal Plac l extr mit de droite CH1 A effectue un retour d entr e un retour vers le point d entr e USING THE FADER START FUNCTION Starting the Cross Fader Set the cross fader switch to CROSS Tum on the fader start switch CH 1 or CH 2 of the channel connected to the player to be controlled Move the cross fader fully to the opposite side of the channel to be started In the example the CH 1 player is fading in Example CROSS FADER i H gt 4 Set the cue point of the player and set the player to standby at this cue point To start playing move the cross fader con trol to the channel to be started at the de sired time Starting the Channel fader Set the cross fader switch to CH Tum on the fader start switch
Download Pdf Manuals
Related Search