Philips HD8752 Coffeemaker User Manual
Contents
1. E This icon is displayed during preheating time required by the machine Ca Yellow al The following icon will be displayed during the dispensing phase Dispense water from the Automatic Milk Frother until clear water flows out Press the button to stop dispensing MEMO Green Clean the suction tube with a damp cloth Weekly Cleaning of the Machine El Clean the seat of the drip tray Clean the pre ground coffee compartment with the brush purchased separately or the handle of a utensil ENGLISH 33 Weekly Cleaning of the Brew Grou The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week E Turn off the machine by pressing the I button and remove the plug from the socket Remove the coffee grounds drawer Open the service door EJ Remove and clean the coffee residues drawer EJ To remove the brew group press the PUSH button and pull it by the handle E Thoroughly wash the brew group with fresh lukewarm water and care fully clean the upper filter BEB caution Do not use detergent or soap to clean the brew group 34 ENGLISH fl Let the brew group air dry thoroughly Thoroughly clean the inside of the machine using a soft dampened cloth EJ Make sure the brew group is in the off position the two reference signs must match If they do no match up proceed as described in st2. The machine should not be used by children younger than 8 years old The machine can be used by children of 8 years and upwards if they have previously been instructed on the correct use of the machine and made aware of the associ ated dangers or if they are supervised by an adult Cleaning and maintenance should not be carried out by children unless they are more than 8 years old and super vised by an adult Keep the machine and its power cord out of reach of chil dren under 8 years old The machine may be used by persons with reduced physi cal sensory or mental capabilities or lacking sufficient experience and or skills if they have previously been instructed on the correct use of the machine and made aware of the associated dangers or if they are supervised by an adult Children should be supervised to ensure that they do not play with the machine Never insert fingers or other objects into the coffee grinder 5 6 ENGLISH Caution The machine is for household use only and is not intended for use in environments such as canteens staff kitchens of shops offices farms or other work environments Always put the machine on a flat and stable surface Do not place the machine on hot surfaces directly next to a hot oven heater or similar source of heat Only put coffee beans into the coffee bean hopper If ground coffee instant coffee or any other substance is put in the coffee bean hopper it may damage th
3. At the end fill the water tank again up to the MAX level Now the ma chine is ready for coffee brewing The display to the left will be shown mm Note When you haven t used the machine for 2 or more weeks the machine will automatically perform an automatic rinse self cleaning cycle after you switch it on Following this you need to initiate a manual rinse cycle as described above The automatic rinse self cleaning cycle starts automatically when the ma chine has been in stand by mode or turned off for more than 15 minutes At the end of the cycle it is possible to brew a coffee 16 ENGLISH Intenza Aroma System Machine Water Hardness Setting Yellow Measuring and Programming Water Hardness Water hardness measuring is very important in order to define the descal ing frequency and to install the INTENZA water filter for more detail on the water filter see next chapter To measure the water hardness follow the steps below E Immerse the water hardness test strip supplied with the machine in water for 1 second Note The test strip can only be used for one single measurement FJ Wait for one minute EJ Check how many squares have changed the colour to red and then refer to the table Note The numbers on the water hardness test strip correspond to the water hardness adjustment settings More precisely 1 1 very soft water 2 2 soft water 3 3 hard wat
4. In this case wait until the machine performs a self adjusting operation as described in Saeco Adapt ing System chapter 56 ENGLISH ENERGY SAVING Stand b The Saeco fully automatic espresso machine is designed for energy saving proven by the Class A energy label After 30 minutes of inactivity the machine turns off automatically If a product has been brewed the machine performs a rinse cycle In stand by mode the energy consumption is below 1Wh To turn on the machine press the I button if the power button on the back of the machine is set to I If the boiler is cold the machine performs a rinse cycle Black Disposal Do not throw away the machine with the normal household waste at the end of its life but hand it in at an official collection point for recycling By doing this you help to preserve the environment Packaging materials can be recycled Machine unplug the machine and cut the power cord Deliver the appliance and power cord to a service centre or public waste disposal facility This product complies with EU Directive 2002 96 EC The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negat
5. then remove plug from wall outlet 12 Do not use appliance for other than intended use 13 Save these instructions SAVE THESE INSTRUCTIONS CAUTION This appliance is for household use only Any servicing other than cleaning and user maintenance should be performed by an authorized service center Do not immerse machine in water To reduce the risk of fire or electric shock do not disassemble the machine There are no parts inside the machine serviceable by the user Repair should be done by authorized service personnel only 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage Never use warm or hot water to fill the water tank Use cold water only Keep your hands and the cord away from hot parts of the appliance during operation Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water For optimal taste of your coffee use purified or bottled water Periodic descaling is still recommended every 2 3 months Do not use caramelized or flavored coffee beans INSTRUCTIONS FOR THE POWER SUPPLY CORD A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may used if care is exercised in their use Ifa long detachable power sup
6. Ceramic Coffee Grinder Ceramic coffee grinders always guarantee accurate and perfect grinding and coarseness for every coffee speciality This technology provides for full aroma preservation delivering the truly Italian taste in every cup PN warning The ceramic coffee grinder contains moving parts that may be danger ous Do not insert fingers or other objects Only adjust the ceramic coffee grinder using the grinder adjustment key You can adjust the ceramic grinders to set the coffee grinding to your personal taste PN warning Only turn the grinder adjustment knob inside the coffee bean hopper when the ceramic coffee grinder is in use This adjustment can be carried out by pressing and turning the grinder adjustment knob inside the coffee bean hopper using the coffee grinder adjustment key provided with the machine Green Green ENGLISH 21 El Press and turn the grinder adjustment knob one notch at a time You will taste the difference after brewing 2 3 cups of coffee The reference marks inside the coffee bean hopper indicate the grind setting There are 5 different grind settings to choose from position 1 for coarse grind lighter taste to position 2 for fine grind bolder taste When you adjust the ceramic coffee grinder to a finer setting your coffee will taste stronger For a milder coffee taste adjust the ceramic coffee grinder to a coarser setting Adjusting the Aroma Coffee
7. Strength Choose your favourite coffee blend and adjust the amount of coffee to be ground according to your personal taste You can also select the pre ground coffee function mm Note Selection must be made prior to selecting coffee Four choices are possible by pressing the 2 button Each time the 2 button is pressed the aroma changes by one degree according to the selected amount MOO mild aroma medium aroma M strong aroma ie amp pre ground coffee 22 ENGLISH Adjusting the Dispensing Spout The height of the dispensing spout can be adjusted to better fit the dimen sions of the cups that you wish to use Move the dispensing spout up or down with your fingers to adjust its height as shown in the image The recommended positions are For the use of small cups For the use of large cups Two cups can be placed under the dispensing spout to brew two coffees at the same time ENGLISH 23 Adjusting the Coffee Length The machine allows you to adjust the amount of brewed coffee according to your taste and or the size of your cups Each time the or button is pressed the machine brews a pre set amount of coffee Each button may be individually programmed for a specific brew setting The following procedure describes the programming of the button E Place a cup under the dispensing spout FJ Press and hold the button until t
8. YES rio 4 DEFAULT SETTINGS d Yellow Yellow Yellow Yellow Yellow Yellow Coffee Temperature This function adjusts the coffee brewing temperature Timer stand by This function adjusts the time taken for the machine to go into stand by mode after the last brewing Contrast This function allows you to adjust the contrast of the display to better view the messages Water Hardness This function adjusts the water hardness setting according to the area where you live 1 very soft water 2 soft water 3 hard water 4 very hard water For more details please see the Measuring and Programming Water Hard ness chapter INTENZA Water Filter This function manages the INTENZA water filter For more details see the chapter about filter handling Descaling cycle This function activates the descaling cycle Factory Settings This function allows you to reset all factory values ENGLISH 49 Programming Example Display contrast d Green In this example it is shown how to program the display contrast Proceed in the same way to program the other functions The programming menu can only be accessed when the machine is on and shows this display El Press the tEm button to access programming The first page is displayed EJ Press the 0 button to scroll the functions pages until the display contrast function is displ
9. new one the following icon is displayed E Replace the filter as described in the previous chapter z L Press the mamm button and scroll through the options by pressing the ON z button until the following icon is displayed OFF 2 zs PRESEM V EJ Select the RESET option Press the O button to confirm EJ To exit press the button The machine shows this display and is l p 5 ready to brew i 0 5 The machine is now programmed to manage a new filter imal Note If the filter is already installed and you want to remove but not replace it select the OFF option instead ESC ATER wi ON FILTER b OFF 4 Yellow If there is no INTENZA water filter installed insert the small white filter previously removed into the water tank 20 ENGLISH ADJUSTMENTS The machine allows for certain adjustments so that you can brew the best tasting coffee possible Saeco Adapting System Coffee is a natural product and its characteristics may change according to its origin blend and roast The machine is equipped with a self adjusting system that allows the use of all types of coffee beans available on the market not for caramelized beans The machine automatically adjusts itself after brewing several cups of cof fee to optimise the extraction of the coffee in relation to the compactness of the ground coffee Adjusting the
10. objects to clean the machine Donot dry the machine and or its components using a microwave and or standard oven E Empty and clean the coffee grounds drawer daily with the machine turned on Other maintenance operations can only be carried out when the machine is turned off and unplugged EJ Empty and clean the coffee residues drawer located inside of the ma chine Open the service door remove the coffee residues drawer and empty the coffee grounds ENGLISH 31 EJ Empty and clean the drip tray Perform this operation also when the full drip tray indicator is raised Daily Cleaning of the Water Tank E Remove the small white filter or the INTENZA water filter if installed from the water tank and wash the tank with fresh water Put the small white filter back or the INTENZA water filter if installed in its housing by gently pressing and turning it at the same time EEJ Fill the water tank with fresh water Daily Cleaning of the Automatic Milk Frother For hygienic reasons and to ensure a perfect milk froth consistency it is im portant that the Automatic Milk Frother be cleaned daily or after each use After each milk frothing you always need to Hl Insert the suction tube in a container filled with fresh water Place an empty container under the Automatic Milk Frother EJ Press the amp 4 button This icon will be displayed Green Press the button to select steam WENO
11. see Us ing the Machine for the First Time chapter The brew group is dirty Clean the brew group see the Weekly Cleaning of the Brew Group chapter The circuit is not primed Prime the circuit see Using the Machine for the First Time chapter This might occur when the machine is automatically adjusting the dose Brew a few cups of coffee as described in the Saeco Adapting System chapter The dispensing spout is dirty This might occur when the machine is automatically adjusting the dose The coffee grind is too fine Clean the dispensing spout Brew a few cups of coffee as described in the Saeco Adapting System chapter Change coffee blend or adjust the grind as explained in chapter Adjusting the Ceramic Coffee Grinder The circuit is not primed Prime the circuit see Using the Machine for the First Time chapter The brew group is dirty The dispensing spout is clogged The Automatic Milk Frother is inserted too deep No milk is being suctioned The cups are cold Note Clean the brew group see the Weekly Cleaning of the Brew Group chapter Clean the dispensing spout and its holes Leave the Automatic Milk Frother to cool down Move it slightly downwards Reposition it in its correct seat Preheat the cups with hot water These problems can be considered normal if the coffee blend has been changed or if the machine has just been installed
12. the button to quit MEMO Fal Remove the water tank and pour the entire content of the Saeco des caling solution Fill the water tank with fresh water up to the MAX level Place the water tank back into the machine EJ Place a large container 1 51 under the steam hot water wand and the dispensing spout 46 ENGLISH OK ESC a bescacer lls E Red Red Red Red Red Red El Press the button to start the descaling cycle E The machine will start dispensing the descaling solution at regular intervals The bar on the display shows the cycle progress Note The descaling cycle may be paused by pressing the lt button To resume the cycle press the button again This allows you to empty the container or to leave the machine unattended for a short time EE When this icon is displayed the water tank is empty Remove the water tank rinse it and fill it up to the MAX level with fresh water Place it back into the machine EEJ Empty the drip tray and place it back EE Empty the container and place it back under both the steam hot water wand and the dispensing spout IE When inserting the water tank into the machine this icon is displayed button to start the rinse cycle fq When this icon is displayed the water tank is empty Repeat steps 12 to 15 Then continue w
13. ENZA Water Filter ADJUSTMENTS 00eseeee Saeco Adapting System Adjusting the Ceramic Coffee Grinder Adjusting the Aroma Coffee Strength Adjusting the Dispensing Spout Adjusting the Coffee Length ESPRESSO AND COFFEE BREWING Espresso and Coffee Brewing Using Coffee Beans Espresso and Coffee Brewing Using Pre Ground Coffee CAPPUCCINO BREWING HOT WATER DISPENSING scsssssssessssssssessssssesscsssssesscsssosecssessesssasessesssesesesen CLEANING AND MAINTENANCE Daily Cleaning of the Machine Daily Cleaning of the Water Tank Daily Cleaning of the Automatic Milk Frother Weekly Cleaning of the Machine Weekly Cleaning of the Brew Group Monthly Cleaning of the Automatic Milk Frother Monthly Lubrication of the Brew Group Monthly Cleaning of the Brew Group with Coffee Oil Remover 41 Monthly Cleaning of the Coffee Bean Hopper 2 DESCALING PROGRAMMING Adjustable Parameters Programming Example MEANING OF THE DISPLAY ICONS TROUBLESHOOTING cccssssssssesssesssessssssssssssessecssecssecssesssecssessseresesesereserers 54 ENERGY SAVING Stand by Disposal na TECHNICAL SPECIFICATIONS cccssssssssssssssssesscsssssesscsssesecsssssesessesesecssessesecees 57 WARRANTY AND SERVICE Warranty Service ORDERING MAINTENANCE PRODUCTG ccsssssossssssssessssssesesssessesss
14. Register your product and get support at www philips com welcome INTELLA EVO Type HD8752 HD8881 USER MANUAL PLEASE READ THIS USER MANUAL CAREFULLY BEFORE USING THE MACHINE Saeco IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 2 3 8 9 Read all instructions Do not touch hot surfaces Use handles or knobs To protect against fire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid Close supervision is necessary when the appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons Do not use outdoors Do not let cord hang over edge of table or counter or touch hot surtaces 10 Do not place on or near a hot gas or electric burner or in a heated oven 11 Always attach plug to appliance first then plug cord into wall outlet To disconnect turn any control to off
15. ally grinds and doses the correct amount of coffee Brewing two espressos or two coffee requires two grinding and brewing cycles automatically carried out by the ma chine al After the prebrewing cycle coffee begins to pour out of the dispensing spout Coffee brewing stops automatically when the pre programmed level is reached it is however possible to stop earlier by pressing the button ENGLISH 25 Espresso and Coffee Brewing Using Pre Ground Coffee This function allows you to use pre ground and decaffeinated coffee With the pre ground coffee function you can only brew one coffee at a time Green Ell Press the button to select the pre ground coffee function Lift the pre ground coffee compartment lid and add one measuring scoop of pre ground coffee to the compartment Use only the measur ing scoop supplied with the machine Then close the pre ground coffee compartment lid WN warning Add only pre ground coffee to the pre ground coffee compartment Other substances and objects may cause severe damage to the ma chine Such damage will not be covered by warranty ll ie MEMO EJ Press the button for an espresso or the button for a coffee The brewing cycle starts E After the prebrewing cycle coffee begins to pour out of the dispensing spout E Coffee brewing stops automatically when the pre programmed level is reached it is however possible to s
16. ayed EJ Press the and buttons to increase or decrease the value of the function 50 ENGLISH ESC Display contrast Yellow e display value is changed the OK message appears Press button to confirm the change E Wheng the KA Press the lY button to exit the programming menu Note The machine will exit the programming mode if the user does not do any thing for 3 minutes The values that have been changed but not confirmed won t be saved ENGLISH 51 MEANING OF THE DISPLAY ICONS This machine is equipped with a colour coded system to make the user s understanding of the display signals easier The icons are colour coded according to the traffic light principle Ready Signals Green Colour The machine is ready to brew products 2 2 U 0g The machine is ready to brew pre ground coffee LP F gt Steam or hot water selection ESC sop Hot water dispensing ee ep STOP Steam dispensing f amp STOP The machine is brewing one cup of espresso TOF The machine is brewing one cup of coffee STOP The machine is brewing two cups of espresso The machine is brewing two cups of coffee 52 ENGLISH Ready Signals Green Colour STOF MEMO STOP LP gt The machine is programming the amount of coffee to be brewed Coffee brewing using pre ground coffee
17. bare hands Use the appropriate protective handle only Before dispensing hot water make sure that the machine is ready to use and the water tank is filled 2 2s Green El Remove the Automatic Milk Frother as shown in the figure Green Yellow Green ENGLISH 29 Place a container under the steam wand EJ Press the 4 button The following icon is displayed 4 Press the button to start dispensing hot water E This icon is displayed during preheating time required by the machine KA Pour the desired amount of hot water To stop the hot water dispens ing press the button Insert the Automatic Milk Frother until it locks in place in the steam wand seat 30 ENGLISH CLEANING AND MAINTENANCE Daily Cleaning of the Machine BEB caution Timely cleaning and maintenance of your machine is very important as it prolongs the life of your machine Your machine is continuously exposed to moisture coffee and limescale The activities you need to perform and their frequency are described in detail in this chapter Not doing this will ultimately make your machine stop working properly This repair is NOT covered by your warranty Note Use a soft dampened cloth to clean the machine Do not wash any removable part in the dishwasher Donot immerse the machine in water Do not use alcohol solvents and or abrasive
18. e machine Let the machine cool down before inserting or removing any parts Never use warm or hot water to fill the water tank Use cold non sparkling drinking water Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water Descale your machine regularly The machine indicates when descaling is needed Not doing this will make your appliance stop working properly In this case repair is not covered under your warranty Do not keep the machine at temperature below 0 C Residue water in the heating system may freeze and cause damage Do not leave water in the water tank when the machine is not used over a long period of time The water can be contaminated Use fresh water every time you use the machine ENGLISH 7 Compliance with Standards The machine complies with art 13 of the Italian Legislative Decree dated 25 July 2005 no 151 Implementation of the Directives 2005 95 EC 2002 96 EC and 2003 108 EC on the restriction of the use of certain hazardous substances in electri cal and electronic equipment as well as waste disposal This machine complies with EU Directive 2002 96 EC This Philips appliance complies with all the applicable stand ards and regulations relating to the exposure to electromag netic fields INSTALLATION Product Overview ENGLISH 9 General Description Ey My R WON E 19 20 21 22 23 24 25 26 27 28 29 30 Grind
19. eps 9 10 E Gently pull down the lever until it is in contact with the brew group base and the two reference signs on the side of the brew group match E Make sure the hook to lock the brew group is in the correct position by firmly pressing the PUSH button until it locks into place Check if the hook is at the top end position If it is not please try again E Insert the brew group in its seat again until it locks into place without pressing the PUSH button ENGLISH 35 Insert the coffee residues drawer and close the service door EE Insert the coffee grounds drawer Monthly Cleaning of the Automatic Milk Frother Every month you need to perform a more thorough cleaning of the Auto PHILIPS matic Milk Frother using the Saeco Milk Circuit Cleaner The Saeco Milk Circuit Cleaner can be purchased separately Please refer to the mainte nance product page in this user manual for further details Milk circuit cleaner E Make sure that the Automatic Milk Frother is correctly installed Pour the milk circuit cleaner into a container Add litre of lukewarm water and wait for the product to dissolve completely EJ Insert the suction tube into the container 36 ENGLISH STOP Green Yellow Green EJ Place a large container 1 51 under the Automatic Milk Frother H Press the 4 button This icon will be displayed Fal Press
20. er 4 4 very hard water The letters correspond to the references that are located at the base of the INTENZA water filter see next chapter EJ Now you can program the water hardness setting Press the tW button and scroll the pages by pressing the 0 button until the fol lowing icon is displayed p The machine is supplied with standard water hardness setting suitable for most types of water PHILIPS Yellow Green ENGLISH 17 E Press the button to increase the value or the button to MEMO decrease the value KA Press the 9 button to confirm the setting Press the button to exit the programming MENU The machine shows this display and is ready to brew INTENZA Water Filter Installation We recommend installing the INTENZA water filter as this prevents limescale build ups and preserves a more intense aroma to your espresso coffee The INTENZA water filter can be purchased separately Please refer to the maintenance product page in this user manual for further details Water is a crucial part of every espresso so it s most important to always have it professionally filtered Using the INTENZA water filter will prevent mineral deposits from building up and improve your water quality E Remove the small white filter from the water tank and store it in a dry place Remove the INTENZA water filter from its packagin
21. er adjustment knob Pre ground coffee compartment Coffee bean hopper Coffee bean hopper lid Control panel Coffee dispensing spout Cup holder grill Full drip tray indicator Drip tray Coffee grounds drawer Brew group Service door Grease for the brew group to be purchased separately Power cord Automatic Milk Frother Suction tube Water tank Power cord socket Steam wand rubber grip for Automatic Milk Frother Coffee grinder adjustment key Pre ground coffee measuring scoop Cleaning brush to be purchased separately Coffee residues drawer Water hardness test strip Espresso brew button Coffee brew button Hot water steam selection button ON OFF button Aroma Pre ground coffee button MENU button Descaling solution to be purchased separately 10 ENGLISH PREPARING FOR USE Machine Packaging The original packaging has been designed and constructed to protect the machine during transport We recommend keeping the packaging material for possible future transport Machine Installation E Remove the drip tray with grill from the packaging Remove the machine from the packaging EJ For best use it is recommended to Choose a safe level surface where there will be no danger of over turning the machine or being injured Choose a location that is sufficiently well lit clean and near an eas ss somm ily reachable socket fomm gt T Allow for a minimum distance from the sides
22. es less than a minute EJ Place a container under the coffee dispensing spout to catch the small amount of water which will be dispensed E The machine shows this display Wait for the cycle to finish automati cally Yellow E Note You can stop dispensing by pressing the button When the above steps are complete the machine shows this display Cc 2 2s Green 14 ENGLISH Manual Rinse Cycle During this process you activate the coffee brewing cycle and fresh water flows through the steam hot water circuit This takes a few minutes E Place a container under the coffee dispensing spout Check that the machine shows this display Q 2s Green EJ Select the pre ground coffee brewing function by pressing the 2 button The machine shows this display Note Do not add pre ground coffee into the compartment Green EJ Press the button The machine starts dispensing water MEMO E When the dispensing has finished empty the container Repeat the operations from step 1 to step 4 twice then continue with step 6 KA Place a container under the steam wand Green Red Green ENGLISH 15 Press the amp button The following icon is displayed EJ Press the button to start dispensing hot water E Dispense water until the no water icon appears E
23. g immerse it ver tically with the opening positioned upwards in cold water and gently press the sides so as to let the air bubbles out 18 ENGLISH ESC WOTER E gt PONA OFF ESC WATER E d Yellow Yellow Green EJ Set the filter according to the measurements performed see previous chapter and indicated on the base of the filter A soft water equals 1 or 2 on the test strip B hard water standard equals 3 on the test strip C very hard water equals 4 on the test strip EJ insert the filter into the empty water tank Press it down until it cannot move any further EEJ Fill the water tank with fresh water and reinsert it into the machine ll Dispense all the water of the tank by using the hot water function see Hot Water Dispensing chapter Fill the water tank again EJ Press the qagmm button and scroll the pages by pressing the but ton until the following screen is displayed EJ Press the button to select ON and press the U button to confirm a HID To exit press the button The machine shows this display and is ready to brew In this way the machine has been programmed to inform the user of the need to replace the INTENZA water filter ENGLISH 19 Replacing the INTENZA Water Filter When the INTENZA water filter needs to be replaced with a
24. ged Clean the hole of the steam wand using a pin Make sure that the machine is off and has cooled down before performing this operation Automatic Milk Frother is dirty if supplied Clean the Automatic Milk Frother Coffee does not have enough crema The blend is unsuitable coffee is not freshly Change coffee blend or adjust the grind as See note roasted or the grind is too coarse explained in the section Adjusting the Ceramic Coffee Grinder The machine takes a long time to warm The machine circuit is clogged by limescale Descale the machine up or the amount of water dispensed from the wand is too little The brew group cannot be removed The brew group is out of place Turn on the machine Close the service door The brew group automatically returns to the initial position The coffee grounds drawer is inserted Remove the coffee grounds drawer before removing the brew group There is a lot of ground coffee under Coffee is not suitable for automatic machines It may be necessary to change the type of coffee the brew group or the coffee grinder settings Machine actions The machine grinds the coffee beans but no coffee comes out See note Coffee is too weak See note Coffee is brewed slowly See note Coffee leaks out of the dispensing spout Milk does not froth Frothed milk is too cold Causes There is no water ENGLISH 55 Solutions Fill the water tank and prime the circuit
25. he MEMO icon is displayed Then release the button The machine has now entered programming mode The machine starts brewing coffee Green EJ When the STOP icon is displayed press the button as soon as the desired amount of coffee is reached Green Now the button is programmed each time it is pressed the machine will brew the same amount of espresso that was just programmed To program the w brew button the same steps should be followed You should always use the button to stop brewing coffee when the desired amount of coffee is reached even when you are programming the brew button 24 ENGLISH ESPRESSO AND COFFEE BREWING Before brewing coffee make sure that there are no warnings shown on the display and that the water tank and coffee bean hopper are filled Espresso and Coffee Brewing Using Coffee Beans Green Green El Place 1 or 2 cups under the dispensing spout EA To brew an espresso or a coffee press the 2 button to select the desired aroma EJ Press the button for an espresso or the button for a coffee MEMO EJ To brew 1 cup of espresso or coffee press the desired button once This icon will be displayed E To brew 2 cups of espresso or coffee press the desired button twice consecutively This icon will be displayed f Note In this operating mode the machine automatic
26. in progress Warning Signals Yellow Colour i R MEMO e STOP S LPs p 0 START The machine is in warm up phase to brew beverages or dispense hot water The machine is in warm up phase during beverages programming The machine is performing the rinse phase Wait until the machine has com pleted the cycle The machine needs the INTENZA water filter to be replaced The brew group is being reset due to machine reset Refill the coffee bean hopper with coffee beans and restart the cycle Prime the circuit The machine needs to be descaled Press the button to enter the descal ing menu Follow the steps described in the descaling chapter of this manual If you want to descale later press the l button to continue using the ma chine Please note that not descaling your machine will ultimately make it stop working properly In this case repair is NOT covered under your warranty ENGLISH 53 Warning Signals Red Colour Close the service door Fill the coffee bean hopper The brew group must be inserted into the machine Insert the coffee grounds drawer Empty the coffee grounds drawer and the coffee residues drawer Fully insert the coffee grounds drawer before turning the machine off Fill the water tank Turn off the machine Turn it back
27. in the figure Wash all the components with lukewarm water Note These components can also be put into the dishwasher for cleaning Attach the lid by pressing in the middle and ensure that it is firmly in place ENGLISH 39 Attach the Automatic Milk Frother to the fitting and ensure it is locked into place in its seat Install the suction tube q G Insert the rubber grip back on the steam wand Insert the Automatic Milk Frother on the rubber grip until it locks into place Ei caution Do not insert the rubber grip further than the seat shown In this case the Automatic Milk Frother would not function correctly as it would not be able to draw up milk 40 ENGLISH Monthly Lubrication of the Brew Grou Lubricate the brew group after approximately 500 cups of coffee or once a month You can purchase the Saeco grease used to lubricate the brew group separately Please refer to the maintenance product page in this user manual for further details BEB caution Before lubricating the brew group clean it with fresh water and let it dry as described in the Weekly Cleaning of the Brew Group chapter E Apply the grease evenly on both side guides Also lubricate the shaft ENGLISH 41 EJ Insert the brew group in its seat until it locks into place see Weekly Cleaning of the Brew Group chapter Insert the coffee residues drawer E Close the service door In
28. indicates when descaling is needed Descaling is required when the machine display shows the CALC CLEAN icon BEB caution Not doing this will ultimately make your machine stop working prop erly and in this case repairing is NOT covered by your warranty Yellow Always use Saeco descaling product only since it has been designed to e optimize machine performance x saeco You can purchase separately the SAECO descaling solution Please refer to j the maintenance product page in this user manual for further details FN warning Never drink the descaling solution or any products dispensed until the cycle has been carried out to the end Never use vinegar as a descaling solution Ji Note Do not turn off the machine during the descaling cycle Otherwise you will need to restart the descaling cycle from the very beginning To execute the descaling cycle follow the steps below Before descaling E Empty the drip tray START ESC OK DEScALER I Yellow Red ENGLISH 45 Remove the Automatic Milk Frother from the steam hot water wand EJ Remove the INTENZA water filter if supplied from the water tank if it was installed E Press the qa button Press the _ button until the following display is shown H Press the button to enter the descaling menu Note If you press the button by mistake press
29. ith step 17 Red Yellow Yellow ENGLISH 47 When the water tank is empty remove it rinse it and fill it up to the MAX level with fresh water Place it back into the machine EE Empty the container and place it back under the dispensing spout GE When the amount of water needed for the rinse cycle has been com pletely dispensed this icon on the side is displayed Press the _ button to quit the descaling cycle The machine automatically primes the circuit The machine now carries out the warm up and automatic rinse cycle to prepare for product brewing Empty the drip tray and place it back Remove and empty the container The descaling cycle is now complete Place the INTENZA water filter if fitted back in the water tank and reinsert the Automatic Milk Frother Note At the end of the descaling cycle wash the brew group as described in the Weekly Cleaning of the Brew Group chapter The two rinse cycles are performed in order to have the circuit cleaned with a pre set amount of water to ensure proper machine performance If the water tank is not filled up to MAX level the machine might require three or more cycles 48 ENGLISH PROGRAMMING The user can change some of the machine operating parameters to suit his her needs Adjustable Parameters Display contrast ESG WATER FILTER EX
30. ive consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product ENGLISH 57 TECHNICAL SPECIFICATIONS The manufacturer reserves the right to make changes to the technical specifications of the product Nominal Voltage Power Rating Power Supply See label on the inside of the service door Housing material Thermoplastic material Size w x hx d Weight 265 5 x 341 x 449 mm 9kg Control panel Front panel Automatic Milk Frother Special for cappuccino Cup size 110mm Water tank 1 5 litres Removable type Coffee bean hopper capacity 300g Coffee grounds drawer capacity 10 Pump pressure 15 bar Boiler Stainless steel type Safety devices Thermal fuse WARRANTY AND SERVICE Warranty For detailed information on your warranty and related conditions please read the warranty booklet supplied separately Service We want to ensure that you remain satisfied with your machine If not done already please register your purchase at www philips com welcome This will enable us to stay in contact with you and send you cleaning and descaling reminders If you need service or support please visi
31. nto the socket located on the back of the machine EE Insert the plug at the other end of the power cord into a wall socket with suitable power voltage 12 ENGLISH IP The display shows the stand by icon Black E EE To turn on the machine simply press the button The display indi cates that the circuit must be primed Yellow USING THE MACHINE FOR THE FIRST TIME When using the machine for the first time the following activities need to happen 1 You need to prime the circuit 2 The machine will perform an automatic rinse self cleaning cycle 3 You need to initiate a manual rinse cycle Circuit Primin During this process fresh water flows through the internal circuit of the machine and the machine warms up This takes a few minutes E Place a container under the steam wand ENGLISH 13 Press the button to start the cycle The machine starts the auto MEMO matic priming of the circuit by dispensing some water through the steam wand EJ The bar under the icon shows the operation progress When the pro cess is completed the machine stops dispensing automatically E1 Then the display shows the machine warm up icon Automatic Rinse Self Cleaning Cycle Yellow Yellow When warm up is completed the machine automatically performs a rinse self cleaning cycle of the internal circuit with fresh water This tak
32. of the machine as 6inches E E i p shown in the illustration 150 mm K 6inches E Insert the drip tray with grill into the machine Make sure it is fully inserted um Note The drip tray collects the water that comes out of the dispensing spout during each rinse self cleaning cycle as well as coffee that might be spilled during beverage preparation Empty and wash the drip tray daily and each time the full drip tray indicator is raised Ei caution NEVER remove the drip tray when the machine has just been turned on Wait a couple of minutes for the machine to carry out a rinse self cleaning cycle ENGLISH 11 EJ Remove the water tank Ql Rinse the water tank with fresh water Fill the water tank with fresh water up to the MAX level and reinsert it into the machine Make sure it is fully inserted BE caution Never fill the water tank with warm hot sparkling water or any other liquid as this may cause damage to the water tank and the machine EJ Remove the coffee bean hopper lid and slowly pour the coffee beans into the coffee bean hopper Note Do not pour too many coffee beans into the coffee bean hopper as this will reduce the grinding performance of the machine BEB caution Only coffee beans must be put into the coffee bean hopper Ground coffee instant coffee caramelized coffee or any other object may damage the machine EJ Put the lid on the coffee bean hopper G Insert the plug i
33. on after 30 seconds Try this 2 or 3 times If the machine does not start contact the Philips SAECO hotline in your country The contact details can be found in the warranty booklet packed separately or on www philips com support 54 ENGLISH TROUBLESHOOTING This chapter summarizes the most common problems you could encoun ter with your machine If you are unable to solve the problem with the information below visit www philips com support for a list of frequently asked questions or contact the Philips Saeco hotline in your country The contact details can be found in the warranty booklet packed sepa rately or on www philips com support Machine actions Causes Solutions The machine does not turn on The machine is not connected to the electric Connect the machine to the electric network network The drip tray gets filled although no Sometimes water is drained automatically by This is a standard operating procedure water is drained the machine into the drip tray to manage the rinsing of the circuits and ensure optimum machine performance The red y icon is always displayed on The coffee grounds drawer was emptied with The coffee grounds drawer must always be emp the machine the machine off tied with the machine on Wait until the L icon is displayed before refitting the drawer Coffee is not hot enough The cups are cold Preheat the cups with hot water No hot water or steam is dispensed The hole of the steam wand is clog
34. ply cord or extension cord is used 1 The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 If the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over Congratulations on your purchase of a Saeco Intelia EVO Class fully automatic coffee machine To fully benefit from the support that Saeco offers please register your product at www philips com welcome This user manual applies to HD8752 and HD8881 The machine is made for preparing espresso coffee using whole coffee beans and for dispensing steam and hot water In this user manual you will find all the information you need to install use clean and descale your machine ENGLISH 3 CONTENTS IMPORTANT ccsscsseseeee Safety Instructions Warning Cautions Compliance with Standards INSTALLATION Product Overview General Description PREPARING FOR USE Machine Packaging 10 Machine Installation USING THE MACHINE FOR THE FIRST TIME Circuit Priming Automatic Rinse Self Cleaning Cycle Manual Rinse Cycle esesessseccccseeessees Measuring and Programming Water Hardness INTENZA Water Filter Installation Replacing the INT
35. r until it locks in place in the steam wand seat Green Yellow Green ENGLISH 27 EJ Insert the suction tube into the milk container BEB caution for hygienic reasons make sure that the suction tube is clean on the outside EJ Place a cup under the Automatic Milk Frother IKA Press the 4 button The following icon is displayed Press the button to start dispensing steam This icon is displayed during preheating time required by the machine EJ When this icon is displayed the machine dispenses frothed milk directly in the cup El Press the button to stop dispensing HX Place the milk container back in the fridge for correct storage 28 ENGLISH Gi After use store the suction tube as shown in the figure Note After having pressed the button it will take a few seconds before the machine stops dispensing steam completely BEB caution After frothing the milk a small quantity of hot water must be dis pensed into a container See chapter Daily Cleaning of the Automatic Milk Frother for detailed cleaning instructions uP Note After dispensing steam it is possible to brew an espresso or dispense hot water straight after HOT WATER DISPENSING FPN warning Danger of burning Dispensing may be preceded by small jets of hot water The Automatic Milk Frother may reach high temperatures Never touch it with
36. sert the coffee grounds drawer Monthly Cleaning of the Brew Group with Coffee Oil Remover Besides weekly cleaning we recommend running the cleaning cycle with Coffee Oil Remover after approximately 500 cups of coffee or once a month This operation completes the maintenance process for the brew group You can purchase separately the Coffee Oil Remover Please refer to the maintenance product page in this user manual for further details BE caution The Coffee Oil Remover tablets are to be used for cleaning only and do not have a descaling function For the descaling procedure use the Saeco descaling solution and follow the procedure described in the Descaling chapter E Place a container under the dispensing spout Make sure the water tank is filled with fresh water up to the MAX level 42 ENGLISH EJ Put a Coffee Oil Remover tablet in the pre ground coffee compart ment J ae BD M El Press the eA button one or more times to select the pre ground cof fee function without adding ground coffee to the compartment CG Green H Press the button to start a coffee brewing cycle MEMO Fal Wait until the machine has dispensed half a cup of water Remove the plug of the power cord from the wall socket EJ Let the solution take effect for approximately 15 minutes Make sure you discard the dispensed water E Reinsert the plug of the power cord in
37. sssosssesenees 58 4 ENGLISH IMPORTANT Safety Instructions This machine is equipped with safety features Nevertheless read the safety instructions carefully and only use the ma chine as described in these instructions to avoid accidental injury or damage Keep this user manual for future reference yN The term WARNING and this icon warn against possible severe injuries danger to life and or damage to the machine K The term CAUTION and this icon warn against slight injuries and or damage to the machine Warnin e Connect the machine to a wall socket with a voltage matching the technical specifications of the machine e Do not let the power cord hang over the edge of a table or counter or touch hot surfaces e Never immerse the machine mains plug or power cord in water danger of electrical shock e Never direct the hot water jet towards body parts danger of burns e Do not touch hot surfaces Use handles and knobs e Remove the mains plug from the wall socket lfa malfunction occurs Ifthe machine will not be used for a long time Before cleaning the machine ENGLISH Pull on the plug not on the power cord Do not touch the mains plug with wet hands Do not use the machine if the mains plug the power cord or the machine itself is damaged Do not make any modifications to the machine or its power cord Only have repairs carried out by a service centre authorised by Philips to avoid a hazard
38. t the Philips website at www philips com support or contact the Philips Saeco hotline in your country The contact number can be found in the warranty booklet packed sepa rately or on www philips com support 58 ENGLISH ORDERING MAINTENANCE PRODUCTS For cleaning and descaling use Saeco maintenance products only You can purchase the products at the Philips online shop if available in your country at www shop philips com service from your local dealer or authorised service centres If you have any difficulties obtaining maintenance products for your ma chine please contact the Philips Saeco hotline in your country The contact details can be found in the warranty booklet packed sepa rately or on www philips com support Overview of maintenance products Descaling solution CA6700 2 PHILIPS _ Saeco S p Intenza water filter CA6702 PHILIPS Saeco Grease HD5061 PHILIPS Milk circuit cleaner Coffee Oil Remover CA6704 Milk Circuit Cleaner CA6705 Maintenance Kit CA 6706 ENGLISH 59 PHILIPS The manufacturer reserves the right to make changes without prior notice www philips com saeco 421946007621 Rev 00 del 15 11 13
39. the button to dispense steam MEMO This icon is displayed during preheating time required by the machine EJ The following icon will be displayed during dispensing When the solu tion is finished press the button to stop dispensing PN warning Never drink the solution dispensed during this step EJ Rinse the container thoroughly and fill it with litre of fresh water to be used for the rinse cycle E Insert the suction tube into the container Green Yellow Green ENGLISH 37 EK Empty the container and place it back under the Automatic Milk Frother Press the YA button This icon will be displayed GE Press the button to dispense steam EMO EE This icon is displayed during preheating time required by the machine EB The following icon will be displayed during dispensing When the water is finished press the button to stop dispensing MEMO EA Wash all the Automatic Milk Frother components by following the instructions below Remove the Automatic Milk Frother from the machine EE Remove the rubber grip from the steam wand BEB caution The steam wand may be hot if the same has been recently used 38 ENGLISH GE Remove the suction tube To detach the Automatic Milk Frother press the sides and remove it by applying light lateral movements as shown in the figure Remove the rubber lid as shown
40. to the wall socket Turn on the machine by pressing the ly button Wait for the automatic rinse cycle to be completed E Remove the coffee grounds drawer and open the service door Remove the coffee residues drawer and then the brew group ENGLISH 43 EE Wash the brew group thoroughly with fresh water After rinsing the brew group insert it again in its seat until it locks into place see Weekly Cleaning of the Brew Group chapter Insert the cof fee residues drawer and the coffee grounds drawer Close the service door IE Press the button to select the pre ground coffee function without adding ground coffee to the compartment G Green EE Press the button to start a coffee brewing cycle MEMO IE Repeat steps 13 to 14 twice Make sure you discard the dispensed water I To clean the drip tray place Coffee Oil Remover tablet inside and fill it 2 3rds full with hot water Let the cleaning solution take effect for about 30 minutes then rinse thoroughly Monthly Cleaning of the Coffee Bean Hopper Clean the coffee bean hopper once a month when it is empty with a damp cloth to remove coffee oil Thereafter refill it with coffee beans 44 ENGLISH DESCALING The descaling process takes approx 35 minutes Limescale builds up inside the machine during use It needs to be removed regularly as it may clog the water and coffee circuit of your machine The machine
41. top earlier by pressing the 4 button After brewing the product the machine returns to the main menu Repeat the steps described above to brew more coffees using pre ground coffee If no pre ground coffee is poured into the pre ground coffee compart ment only water will be dispensed If the dose is excessive and 2 or more scoops of pre ground coffee are used the machine will not brew the product and any ground coffee will be discharged into the coffee grounds drawer 26 ENGLISH CAPPUCCINO BREWING PN warning Danger of burning Dispensing may be preceded by small jets of hot water The Automatic Milk Frother may reach high temperatures Never touch it with bare hands Use the appropriate protective handle only E Fill 1 3 of a container with cold milk Note Use cold 5 C 41 F milk with a protein content of at least 3 to ensure optimum results when preparing a cappuccino Whole milk or skimmed milk may be used depending on individual taste Notes When you plan to dispense steam right after switching on the machine or after brewing a coffee some water still present in the circuit may need to be dispensed first For this press the Gy button and then the button to dispense steam for a few seconds Thereafter press the button to stop dispens ing Then continue with step 2 MEMO FA Insert the suction tube into the Automatic Milk Frother EJ Insert the Automatic Milk Frothe
Download Pdf Manuals
Related Search