Philips 26HFL3350D/10 Flat Panel Television User Manual
Contents
1. Note 2 If the SLEEPTIMER is in progress the current SLEEPTIMER countdown timer value appears in the ITV commercial SETUP MENU as well as in the FEATURES MENU The SLEEPTIMER period can of course also be reset from either menu FEATURES MENU 9 MIN SLEEPTIMER Countdown In Progress example SECURITY STANDARD HIGH Special feature for commercial use only 24 105 User s Manual 091105 1833 26HW9100D Dimensions 30 21 19 81 105 User s Manual 091105 1833 30HW9100D Dimensions 33 86 21 73 262. see Note NO TV upon receiving a remote control digit command expects to receive one more successive remote control digit command before tuning the intended channel see Note Note Successive digit commands must occur within two seconds or the TV will interpret the previously received digit s as constituting the intended channel and tune accordingly A CH A V SWITCH NO YES The A CH A V alternate channel A V switch feature provides the choice to use the remote control A CH command to either switch between the current and previously tuned channels inputs or to step successively through all sources e g ANTENNA tuner AUX S VIDEO CVI FRONT presently in the channel ring YES Upon receiving an alternate channel A CH command the TV will tune to the next signal source e g tuner AUX S VIDEO etc if any in the channel ring NO Upon receiving an alternate channel A CH command the TV will switch to the most recently selected channel input CC OFF CC 1 CC 2 CC ON MUTE Closed Captioning Since July 1 1993 television sets with 13 screens or larger must have built in caption decoders Captioning of most broadcast and cablecast programming is mandated under the Telecommunications Act of 1996 except for certain types of programs exempted by the FCC For additional information please visit the U S FCC web site at http ftp fcc gov cgb consumerfacts closedcaption html OFF Regardless of wh
3. V CHIP line item does not appear in the FEATURES MENU YES The V CHIP line item appears in the FEATURES MENU SAVE V CHIP NO YES This feature provides the option to specify whether the current V CHIP SETUP configuration remains in effect after the television is powered down NO The current V CHIP setup configuration reverts to defaults when the television 15 powered down YES The current V CHIP setup configuration remains in effect when the television is powered down V CHIP SETUP gt Configures the V CHIP program content viewing restriction feature Please consult the mainstream consumer product documentation for information about this feature NO current V CHIP setup configuration reverts to defaults when the television 15 powered down YES The current V CHIP setup configuration remains in effect when the television 15 powered down SLEEPTIMER OFF 15 MIN 30 MIN 45 MIN 60 MIN 90 MIN 120 MIN 180 MIN 240 MIN Activates the SLEEPTIMER feature in which the television powers down automatically after the specified period of time Note 1 The SLEEPTIMER feature differs from ESP energy saving programmability in that the SLEEPTIMER countdown timer continues regardless of whether the 25 105 User s Manual 091105 1833 television receives a remote control or front panel command whereas the ESP timer is reset whenever the television receives a command from a remote control or from the front panel
4. 105 User s Manual 091105 1833 TV 26HW9100D 30HW9100D User s Manual PHILIPS 105 User s Manual 091105 1833 SAFETY INFORMATION Disconnect mains plug when the red light below the TV screen is flashing continuously gt a bright white line is displayed across the screen cleaning the TV screen Never use abrasive cleaning agents Use a slightly damp chamois leather or soft cloth there is a lightning storm the set is left unattended for a prolonged period of time No open flame sources such as lighted candles should be placed on or near the TV Do not place your TV set under direct sunlight or heat Leave at least 1 4 around each side of TV set for sufficient ventilation to avoid over heating Avoid placing set where it 1s likely to be exposed to rain or water e g near the window No objects filled with liquids should be placed on top the TV in order to avoid dripping or splashing of liquids into the set USEFUL TIPS Do not leave the television off in standby mode for a prolonged period of time Switch off set to allow the CRT to be de gaussed demagnetized A de gaussed CRT will have optimum picture quality Do not re position the television while it is switched on Nonuniformity in screen color may result Never attempt to repair a defective TV yourself Always consult skilled service personnel 105 User s Manual 091105 1833 Before Calling Service A list of common symptoms is p
5. 3 Check line 10 of the menu to see if the TV is in the Commercial or Consumer mode 4 If the TV is in the Commercial mode then proceed to Part B to activate the TV Setup menu Otherwise go to Part C to change the TV mode to Commercial Part B To activate TV Setup menu Press the RECALL key to clear the menu Press MENU to activate the TV Setup menu me Part C To select Commercial mode if the TV 1s in Consumer mode or to select Consumer mode if the TV is in Commercial mode 105 User s Manual 091105 1833 IU gt Press the RECALL key to clear the menu Press 02 4 9 9 5 Press M key and the TV Mode menu appears Press or to select Commercial mode Highlight STORE and press the 4 key to store the change TV will then go to standby mode Press any numeric key to switch on the TV again and follow the procedure in Part B step 2 to activate the TV Setup menu 105 User s Manual 091105 1833 TV Setup Main Menu ENTER DIGITAL MENU DEFAULT FORMAT WIDESCREEN 4 3 ZOOM 14 9 ZOOM 16 9 SUBTITLE ZOOM SUPER ZOOM MIN VOLUME O 100 MAX VOLUME 100 SWITCH ON VOLUME STANDARD IE 100 SWITCH ON CHANNEL STANDARD TV 1 125 AV 1 AV 2 SIDE S VIDEO CVI AV3YC HDMI HD CVI POWER ON SLANDARD FORCED RESTORED CHANNEL DISPLAY NONE NUMBER LABEL ALL SLEEPTIMER OFF 15 MIN 30 MIN 45 MIN 60 MIN 90 MIN 240 MIN SECURITY STANDARD HIGH Only 8 menu items will be d
6. 573GR setup remote control when it 1s in setup mode information similar to the following will appear on the TV screen This information describes the TV chassis firmware version diagnostic codes setup information and other service and technical data regarding the television configuration Line 10 indicates whether the TV 1s in CONSUMER or COMMERCIAL mode and whether it is on line with a SmartPort DCM such as a CLON99BK SmartLoader For more information please refer to the service documentation for the ITV BDS L05 TV chassis 105 User s Manual Source Select To toggle between available video sources DVD PAUSE To Pause DVD nlavback Close Caption To activate Close Caption functionality DVD STOP To Stop DVD playback 1f applicable Menu To call up or exit the menus Vol To adjust the volume Mute Interrupt the sound or restore it 0 9 Digit keys To select a TV channel For a two digit program number enter the second digit before the dash appears Alternate Channe To toggle between alternating channels uest Remote Control Kevs CH Guide To activate Channel Guide functionalitv PLAY UC SOURCE GUIDE PHILIPS 091105 1833 Standby Press to switch the TV off DVD PLAY To Start DVD playback if annlicable DVD Rewind To Rewind DVD nlavhack DVD FAST FORWARD To Fast Forward DVD playback if applicable Smart Keys To select predefined picture and sound setting
7. ENNA In other words TV channel 2 could be used to select the AV 1 video input instead of RF ANTENNA channel 2 Special instructions for mapping digital channels are included below AUTO PROGRAM o When AUTO PROGRAM is selected the TV performs an automatic search for the presence of viable RF signals at its tuner input An AUTO PROGRAMMING ACTIVE message and a table of channel numbers will appear If CABLE TUNING 1s set to NO channels 2 through 69 will be checked If CABLE TUNING 15 set to YES channels 2 through 125 will be checked When a viable signal is detected on a given channel that channel is highlighted in red and is added to the channel ring Any command from a remote control terminates the AUTO PROGRAM session Front panel commands do not cancel auto programming e CHANNEL RING 11 105 User s Manual 091105 1833 o Specify whether the current channel or input 1s to be SAVED to or DELETED from the channel ring 1 list of channels available for selection by means of standard guest remote control LABEL o Input a maximum of 8 characters for the channel s label Cursor to the Right to start the first character Cursor left or right to navigate between character positions within the label field Cursor up or down to select characters from the list A to Z to 9 lt gt or space To edit re input the character at its position To exit cursor left or right to navigate out of the labe
8. NO channel or the channel referred to in the digital channel table USE CHANNEL TABLE YES e MINOR CHANNEL o MINOR CHANNEL refers to the digital sub channel related to the MAJOR CHANNEL specified above e CHANNEL RING o Specify whether the current channel or input is to be SAVED to or DELETED from the channel ring 1 list of channels available for selection by means of standard guest remote control LABEL o Input a maximum of 8 characters for the channel s label Cursor to the Right to start the first character Cursor left or right to navigate between character positions within the label field Cursor up or down to select characters from the list A to Z to 9 lt gt or space To edit re input the character at its position To exit cursor left or right to navigate out of the label editing field VIDEO BLANK o Specify whether video for the current channel is to be displayed VIDEO BLANK NO or not displayed VIDEO BLANK YES AUDIO MUTE o Specify whether audio for the current channel is to be audible AUDIO MUTE NO or muted AUDIO MUTE YES CABLE NO YES Select either standard off air tuning CABLE TUNING NO or cable offset tuning CABLE TUNING YES FACTORY CH RESET gt Cursor Right will reset the channels programmed in memory 13 105 User s Manual 091105 1833 USE CHANNEL TABLE NO YES When NO is selected the MAJOR channel in the Digital channel set
9. RES MENU YES The SOURCE line item appears in the FEATURES MENU Note 1 When the SOURCE item is highlighted cursor right or left to step through the signal sources e g tuner AUX S VIDEO etc that are in the CHANNEL RING The SOURCE item in the FEATURES MENU cannot be used to select RF tuner channels Note 2 The SOURCE item can only be used to select signal sources e g tuner AUX S VIDEO etc that are in the CHANNEL RING Note 3 If there are no signal sources in the channel ring other than the presently selected source the SOURCE item 15 for indication only and cannot select any other sources HDMI AUDIO SELECTION HDMI AV1 AV2 AV 3 This menu item allows the user to associate an audio input to the HDMI input Devices with an HDMI output usually have digital audio included on the HDMI output however outputs such as DVI have no audio included on the connector For those devices with a 22 105 User s Manual 091105 1833 DVI output a DVI to HDMI converter is required for the video input to the television and the analog audio can be configured on any of the listed audio inputs V CHIP MENU ITEM NO YES This feature provides the option to specify whether the V CHIP SETUP menu item is present in the FEATURES MENU which appears when the remote control SLEEP or CC command is issued or when a guest mode remote control RECALL command is issued FEATURES MENU Features Menu With V CHIP Menu Item YES NO The
10. e minimal or possibly degraded depending upon various factors ULTRA BASS NO YES When ULTRA BASS is set to YES the audio frequency equalization is modified such that the bass frequencies are significantly emphasized VOLUME BAR NO YES When VOLUME BAR is set to YES an OSD graphic appears that provides visual verification e g 15 during volume adjustment by means of either the remote control or the front panel if it is not locked out MIN VOLUME 0 100 Specify the lowest volume setting possible by means of either the remote control or the front panel if it is not locked out This setting cannot exceed MAX VOLUME see MAX VOLUME Note The MIN VOLUME setting 15 effective whether the volume command is issued from the front panel if it is not locked out a standard guest mode remote control or an RC2573GR setup remote in setup mode 17 105 User s Manual 091105 1833 MAX VOLUME O 100 Specify the highest volume setting possible by means of either the remote control or the front panel if it is not locked out This setting cannot be less than MIN VOLUME see MIN VOLUME Note The MAX VOLUME setting 1s effective whether the volume command is issued from the front panel if it is not locked out a standard guest mode remote control or an RC2573GR setup remote in setup mode SWITCH ON VOLUME STANDARD 0 100 Specify the volume setting that takes effect when th
11. e TV is powered on If STANDARD the volume at power on will be the volume at which the TV was prior to last power down If specified as 0 63 that will always be the volume at power on until SWITCH ON VOLUME is changed SWITCH ON CHANNEL STANDARD TV 1 125 AUX FRONT S VIDEO CVI Specify the channel input to which the TV will be tuned when it is powered on If STANDARD the channel at power on will be that to which the TV was tuned at last power down If specified e g 2 AUX etc then that will always be the channel input at power on until SWITCH ON CHANNEL 15 changed POWER ON STANDARD FORCED RESTORED STANDARD The TV will be in standby mode when AC mains power is first applied after having been disconnected FORCED The TV will turn ON whenever AC mains power is applied This feature allows the TV s power status to be controlled for example from an AC mains breaker RESTORED When AC mains power is first applied after having been disconnected the TV s power status will revert to that when AC mains power was last removed CHANNEL DISPLAY NONE NUMBER LABEL ALL Specifies which of the respective channel properties are displayed by the TV s OSD when a channel or input is first selected If REMINDER see REMINDER is OFF these properties will be displayed for a few seconds then disappear If REMINDER is ON the channel properties remain on screen whenever the TV 15 on KEYBOARD LOCK NO YES NO T
12. ether there 1s a closed captioning signal present on the current source closed captioning will not appear CC 1 CC 1 mode closed captioning will be displayed if it is present on the incoming signal 21 105 User s Manual 091105 1833 CC 2 CC 2 mode closed captioning will be displayed if it is present on the incoming signal CC ON MUTE If the television is in audio mute mode CC 1 mode closed captioning will be displayed if it is present on the incoming signal Note When the television 1s powered down and back on again the closed captioning setting will default to OFF unless SAVE CC see SAVE CC is set to YES SAVE CC NO YES Save closed captioning This feature enables the CC setting see CC to remain in effect after the television 1s powered down NO When the television is powered down and back on again the closed captioning setting will default to OFF YES When the television is powered down and back on again the closed captioning setting last specified in CC see CC will remain in effect SOURCE MENU ITEM NO YES This feature provides the option to specify whether the current signal source e g TV 54 AUX CVI S VIDEO etc item 1s present in the FEATURES MENU that appears when the remote control SLEEP or CC command is issued or when a guest mode remote control RECALL command is issued FEATURES MENU Features Menu With SOURCE MENU ITEM YES NO The SOURCE line item is does not appear in the FEATU
13. he TV s front panel is operational YES The TV s front panel is rendered inoperative Note Even when KEYBOARD LOCK NO not locked out front panel power on off volume or channel controls might have no effect depending upon the settings of POWER ON STANDARD FORCED CHANNEL INSTALL MIN VOLUME and MAX VOLUME 18 105 User s Manual 091105 1833 ESP OFF 1 HR 2 HR 99 HR Energy Saving Programmability This feature enables the TV to automatically power down after a specified period of time if during any such period it receives no commands from the front panel or remote control This 1s an energy saving feature which assumes that the TV after the specified period of inactivity 1s no longer being viewed AUDIO VIDEO MUTE OFF BLACK BLUE Also known as A V muting Suppresses audio and video when the TV tuner is supplied with an inadequate signal level When there is insufficient RF signal level to the TV tuner the options produce the following results OFF Screen displays snow and the audio is white noise static BLACK Screen display is black and the audio is muted BLUE Screen display is blue and the audio is muted AUDIO VIDEO OUT MUTE NO YES When set to YES turns off the audio and video MONITOR OUT signals either demodulated RF input or loop through video Intended to prevent recording of pay per view content MONITOR OUT RF NO YES This features configures the audio and video monito
14. he channel guide appears automatically at power on and remains on screen for approximately 10 seconds or until a remote control command occurs The channel guide also appears when CH GDE on remote is pressed Note 1 To appear in the channel guide an RF tuner channel must be assigned a label and must be saved in the channel ring 20 105 User s Manual 091105 1833 Note 2 Only RF tuner channels will be listed in the channel guide Video inputs AUX S VIDEO CVI FRONT A V will not appear in the channel guide REMINDER NO YES When REMINDER YES the reminder feature provides a constant onscreen indication of the current channel or input e g TV 2 CVI etc that channel s or input s label if a label has been assigned in CHANNEL INSTALL and the current MUTE status 1 e if sound MUTE is active The REMINDER orscreen indication appears near the top of TV screen viewing area When REMINDER NO the reminder information appears only when the channel or input is changed then disappears after approximately ten seconds 3 DIGIT ENTRY NO YES YES The TV upon receiving a remote control digit command expects to receive up to two more successive remote control digit commands e g 123 012 etc before tuning the intended channel The television will display in the upper left hand corner of the screen each digit as it is received followed by a hyphen indicating that the TV is waiting for the next digit
15. heck that the sound is not muted If it is muted press the Mute button on the remote control to restore sound Check the MIN VOLUME MAX VOLUME settings in the setup menu Sound ok but poor color or no picture Check picture adjustments brightness contrast color tint Snowy noisy picture e Check antenna cable and or set top box connections and antenna cable e Possible electrical interference from appliances or other sources Double images ghost images Television does not respond to remote control Check batteries e Aim remote control handset directly at remote control sensor lens on the TV Channel Change to digital channels is slow Channels must be programmed in the Digital OSD menu for the shortest channel change time Note These televisions are shipped in commercial mode with Digital OSD turned ON If pressed while on a digital channel the television will display the digital menu instead of the commercial menu To properly configure the television using the commercial menu it is necessary to be on an analog channel to access the setup menu 105 User s Manual 091105 1833 Basic Television Connection 117 VAC 60 HZ A xut ap se R i 4 a 105 User s Manual 091105 1833 Use And Care of Remote Control To load the supplied batteries into the remote control Remo ve the battery compartment lid from the back of the remote control I
16. isplayed at one time 1 To scroll through the menu press 191 cursor up down on the remote control A highlight indicates that the respective menu item s setting is selected for modification 2 To modify the setting of the selected menu item press lt 4 lt 9 cursor left nght MENU 3 To exit press or RECALL on the RC2573GR setup remote control 10 105 User s Manual 091105 1833 TV Setup Menu and Sub Menus LANGUAGE English Espanol Francais When you first enter the TV SETUP menu LANGUAGE is highlighted You can scroll to the LANGUAGE item Select the desired language with cursor up cursor down CHANNEL INSTALL gt The CANNEL INSTALL menu allows the user to configure the channels that can be accessed When installing the channels different inputs can be mapped to TV channels to allow seamless integration into the channel map The two sections below explain how to install analog channels and AV inputs and how to install digital channels Installing Analog channels When selected CHANNEL INSTALL menu appears as follows Configure the inputs and channels as described CHANNEL INSTALL CHANNEL o Select the channel or input you wish to configure INPUT o Select the input source that you wish to associate with the specified CHANNEL This feature enables you to map re assign a numeric channel number to a video input rather than to its normal RF TV channel i e ANT
17. l editing field VIDEO BLANK o Specify whether video for the current channel is to be displayed VIDEO BLANK NO or not displayed VIDEO BLANK YES AUDIO MUTE o Specify whether audio for the current channel is to be audible AUDIO MUTE NO or muted AUDIO MUTE YES Installing AV Inputs CHANNEL INSTALL CHANNEL o Select the input you wish to configure LABEL o Input a maximum of 8 characters for the channel s label Cursor to the Right to start the first character Cursor left or right to navigate between character positions within the label field Cursor up or down to select characters from the list A to Z 0t09 lt gt or space To edit re input the character at its position To exit cursor left or right to navigate out of the label editing field VIDEO BLANK o Specify whether video for the current channel is to be displayed VIDEO BLANK NO or not displayed VIDEO BLANK YES e AUDIO MUTE o Specify whether audio for the current channel is to be audible AUDIO MUTE NO or muted AUDIO MUTE YES 12 105 User s Manual 091105 1833 Installing Digital Channels CHANNEL INSTALL CHANNEL o Select the channel or input you wish to configure INPUT o When DIGITAL is selected two additional entries are added to the menu to allow for mapping the digital channels MAJOR CHANNEL o MAJOR CHANNEL refers to the either the DIGITAL RF USE CHANNEL TABLE
18. les visible Super Zoom This mode is used to display 4 3 pictures using the full surface of the screen by enlarging the sides of the picture Widescreen This mode restores the correct proportions of pictures transmitted in 16 9 using the full screen display NOISE REDUCTION NO YES Disable or enable the video noise reduction feature in which video noise is reduced with minimum reduction in picture sharpness 16 105 User s Manual 091105 1833 SOUND MODE MONO STEREO Select either STEREO or MONO moraural sound modes Note STEREO has no effect if the current audio signal is monaural When SOUND MODE is changed an onscreen display will appear indicating the actual audio status MONO or STEREO AVL OFF ON Disable or enable the Automatic Volume Leveling feature which minimizes variations in audio playback level BALANCE 31 31 Adjust the respective audio playback setting TREBLE 0 100 Adjust the respective audio playback setting BASS 100 Adjust the respective audio playback setting INCREDIBLE STEREO NO YES When INCREDIBLE STEREO 15 set to YES and the current SOUND MODE is MONO a signal processing technique is applied for the purpose of simulating a stereo like effect Note When INCREDIBLE STEREO 15 set to YES and the current SOUND MODE is STEREO regardless of whether there 1s a stereo signal on the current channel the resultant effect will be imperceptibl
19. nsert the correct type of batteries into the compartment Ensure that the and ends of the batteries are placed in the correct positions Re attach the battery compartment lid Note Always remove the batteries from the remote control if it is not to be used for a long period This can help prevent damage to the remote from possible battery leakage Rear Jack Panel Connections CABLE ANTENNA S Video f AV1 in 2 in LiMono VUES e AUDIO once S Video anges f ah AUDIO UR X 5 3 d R WM COMPONENT VIDEO PUT HDMI 105 User s Manual 091105 1833 REMOTE CONTROLS The following remote controls are applicable to the 105 HW series television products These can be used for setup and configuration purposes e 86 6 y o 0 o o o o 7 oe ele moe dul 3 gt O eee RC2888 01 RC2573GR Guest Remote Setup Remote Optional For the purpose of explanation a guest remote for 1 04 series similar to the illustration is used Remote control RC2573GR is a special and optional remote control specifically for configuring Institutional TV Business Display Solutions features and SmartCard settings and is purchased separately Refer to the documentation for the RC2573GR for detailed information When you press RECALL on the RC2
20. ote If welcome message is enabled and both LINE 1 and LINE 2 are blank or consist entirely of space characters no message will appear e LINE 1 LINE 2 Select message LINE or LINE 2 When you first cursor left or right the gt at the end of the menu line disappears and a blinking hyphen character indicates message edit mode Cursor up or down to select a character at the given position Cursor left or right to move the cursor to the desired character position Note When you cursor to the left or right margins of the edit space the blinking hyphen will disappear and gt will re appear at the very end of the menu line You can then cursor up or down to the next or previous line in the MESSAGE sub menu e CLEAR 2 Erase the entire message CHANNEL GUIDE NO YES POWER ON The channel guide feature provides an on screen summary listing of the RF tuner channels that are currently in the channel ring see CHANNEL INSTALL gt CHANNEL RING and have been assigned labels see CHANNEL INSTALL gt LABEL CHANNEL GUIDE CH GUIDE TO SCROLL DOWN NO Channel guide is not displayed when CH GDE on remote is pressed and a NOT AV AILABLE message appears YES When CH GDE on remote is pressed the channel guide is displayed for approximately 10 seconds or until a remote control command occurs RF tuner channels that are in the channel ring and have labels will appear in the channel guide list POWER ON T
21. picture setting using left and right cursor TINT 31 31 Adjust the respective picture setting using left and right cursor ROTATION IH 0 100 Adjust the respective picture setting using left and right cursor DEFAULT FORMAT WIDESCREEN 4 3 ZOOM 14 9 ZOOM 16 9 SUBTITLE ZOOM SUPER ZOOM Set the default screen format of the television at Power On The pictures you receive may be transmitted in 16 9 format wide screen or 4 3 format conventional screen 16 9 pictures sometimes have a black band at the top and bottom of the screen letterbox format This function allows you to optimize the picture display on screen 15 105 User s Manual 091105 1833 Using the different formats Select the preferred format from the DEFAULT FORMAT menu item in the setup screen or if applicable use the Format button on the Remote Control to select the different modes 4 3 Zoom 14 9 Zoom 16 9 Subtitle zoom Super Zoom and Widescreen 4 3 The picture is reproduced in 4 3 format and a black band is displayed on either side of the picture Zoom 14 9 The picture is enlarged to 14 9 format a thin black band remains on both sides of the picture Zoom 16 9 The picture is enlarged to 16 9 format This mode is recommended when displaying pictures that have black bands at the top and bottom letterbox format Subtitle Zoom This mode is used to display 4 3 pictures using the full surface of the screen leaving the subtit
22. r outputs provided that AUDIO VIDEO OUT MUTE is not set to YES NO The signals that are present at the monitor outputs are the same as those of the currently selected channel or video input In other words the monitor outputs track what 1s viewed and heard on the TV YES The signals that are present at the monitor outputs are always the tuner output see NOTE below regardless of whether the currently selected TV source is the tuner or video 1 e AUX S VIDEO CVI input Note When MONITOR OUT RF is initially changed from its current setting the monitor out signal source depends upon the previous MONITOR OUT setting until a different TV source is selected From that point until it is changed the new MONITOR OUT setting will perform as described WELCOME MESSAGE 2 A welcome message two lines 20 characters can appear on screen when the set 1s powered on The message remains on screen until the TV receives a command from the remote or front panel When the WELCOME MESSAGE setup menu item is highlighted cursor right or left to invoke the MESSAGE sub menu Cursor up or down to select the desired MESSAGE sub menu item Press RECALL or MENU to return to the SETUP main menu WELCOME MESSAGE lt E LT 5 29 va WO YES Ls im a 19 105 User s Manual 091105 1833 e DISPLAY NO YES Cursor right or left to select NO to disable the WELCOME MESSAGE or YES to enable it N
23. resented as follows Before you call for service perform these simple checks Some of these symptoms can be readily corrected Note Please become familiar with the commercial features as described in TV Installation Setup because the effects of several of these features if they are not thoroughly understood might appear as faulty operation Symptom Possible Corrective Action TV does not respond to commands volume Check commercial TV setup TV installation channel power or cannot be turned on if it is off setup menu settings including power forced on or cannot be turned off if it is on front keypad lockout channel ring volume minimum maximum features turns off by itself TV automatically turns off after approx 5 minutes when no RF signal is present Check Energy Saving Programmability setting see ESP in TV installation setup Lack of color uniformity color unevenness Switch off the TV using the mains power button Wait approximately 20 minutes before switching on again Ensure that the TV is not placed near speakers or magnetic objects Verify that the TV s AC power cord is plugged into the mains socket If there 1s still no power disconnect plug Wait for 60 seconds and re insert plug Switch on the TV again No picture Check antenna connection at rear of the TV Check CABLE TUNING setting NO YES Possible TV station problem Try another channel Picture ok no sound Try increasing the volume C
24. s Sleep Activates the sleep timer Press repeatedly to increment the countdown time with 15 minutes CH Channel Selection To move up or down a TV channel 16 9 Formats To adjust TV screen formats 105 User s Manual 091105 1833 Consumer vs Commercial Mode The television is shipped in Commercial mode however at times it may be necessary to operate the set in Consumer mode To switch between Commercial Mode and Consumer Mode the following sequence should be followed MENU e With the RC2573GR Master setup remote enter 024995 and press the key e Use the Right cursor button to switch the Mode of the set between Consumer and Commercial e With the proper mode selected cursor down and use the Right cursor button to store the selected mode e After the mode is stored the television will power itself off At this point disconnect AC and perform a cold start on the television e The set should now be in the selected mode Accessing TV Setup Menus With remote control RC2888 01 only when SECURITY in the TV SETUP menu is set to LOW To activate TV Setup menu 1 Select a channel number 2 Keyin319753 MENU 3 Press The above sequence should be performed within 20 seconds and the TV SETUP menu will appear With remote control RC2573GR only in TV Commercial mode Part A To check the television s mode 1 Set the remote control selectable switch to SETUP Press RECALL key and the TV Status menu will appear
25. up in the CHANNEL INSTALLATION menu refers to an RF channel frequency When YES is selected the Major channel refers to the Major channel listed in the Digital Channel Map DIGITAL OSD NO YES Specify whether the consumer digital version of the OSD is displayed when MENU MENU is pressed from a digital channel ENTER DIGITAL MENU gt Cursor RIGHT will bring up the Consumer DIGITAL Menu below The primary use of this menu is to program the digital channels using the Auto Program function of the digital module in the television To program the digital channels cursor down to Install and Cursor Right This will display the Install Menu From The Install menu select Auto Program and Cursor Right to start the Auto Programming INSTALL Auto Program Install Channel Edit char 14 105 User s Manual 091105 1833 Auto scan Tuner input Air Autoscanning Digital 6 Note The digital channels must be programmed using the Digital Menu to allow for the fastest possible channel change times MENU To exit the digital menu press the key on the setup remote twice BRIGHTNESS HEIN 0 100 Adjust the respective picture setting using left and right cursor COLOR O 100 Adjust the respective picture setting using left and right cursor CONTRAST O 100 Adjust the respective picture setting using left and right cursor SHARPNESS 0 100 Adjust the respective
Download Pdf Manuals
Related Search