Pelco IPS-RDPE-2 Marine GPS System User Manual
Contents
1. 8 1 roller with UTP Video Point to Point Configuration 1 roller with UTP Video Home Run Configuration 1 roller with UTP Video Daisy Chain Configuration 5 1 Important Safety Instructions Prior to installation and use of this product the following warnings should be observed 1 Installation and servicing should be done only by qualified service personnel and conform to all local codes Use only replacement parts recommended by Pelco Use stainless steel hardware to fasten the unit to outdoor surfaces If the unit does not have an on off switch the input power circuit must have a circuit breaker Use only installation methods and materials capable of supporting four times the maximum specified load A CCC approved power cord must be used to power this equipment when used in China C2473M C 8 06 Description Pelco s IPS RDPE 2 data port box is an on site service tool designed for Spectra III SE Spectra III Esprit and ExSite Series positioning systems The data port box gives on site access for setup and testing of the positioning system The IPS RDPE 2 can be used to locally view video and control pan tilt zoom functions of a Spectra IIl SE Spectra Ill Esprit or ExSite system The data port box can also upload revised operating software and language files to a Spectra Series Ill SE Spectra IIl2. POSITIONING SYSTEM VC UTP POWER UTP UTP PTZ CONTROL AND SOFTWARE UPLOAD POSITIONING SYSTEM PTZ CONTROL AND SOFTWARE UPLOAD IPS RDPE 2 RX RX TX TX UTP UTP UTP UTP TO POWER SUPPLY VC UTP TX TX RX RX UTP UTP UTP RECEIVER TX TX RX RX UTP UTP CONTROL SYSTEM AT CONTROL SYSTEM UTP UTP dq UTP RECEIVER AT CONTROL SYSTEM RX RX TX TX UTP UTP UTP UTP TO POWER SUPPLY Figure 11 RS 422 D or P Protocol Controller with UTP Video Daisy Chain Configuration Input power for the IPS RDPE 2 is 24 VAC only The maximum wire gauge allowed for power input and output is 12 AWG The maximum wire gauge allowed for UTP is 16 AWG Refer to the manual supplied with the positioning system for wiring distances and coaxial cable requirements C2473M C 8 06 Operation To view video control pan tilt zoom or upload revised operating software and language files to a positioning system do the following 1 2473 8 06 Open the door of the IPS RDPE 2 Opening the door will automatically disconnect the controller at the head end and trigger an audible alert at the IPS RDPE 2 site NOTE The audible alert indicates that the data port is in service mode and also serves as a reminder to close the door after servicing the positioning system Connect the RJ 45 connector of the IPS CABLE not supplied to
3. b Connect the power wires from the positioning system to the 24 VAC OUT positions on the power connector of the IPS RDPE 2 NOTE If preferred separate power supplies can be used for the IPS RDPE 2 and the positioning system Connect the video wires cable from the positioning system to either the BNC VIDEO IN connector if using coaxial or UTP VIDEO IN connector if using UTP of the IPS RDPE 2 Run conduit with wiring from the power supply and wiring from the controller at the head end to the IPS RDPE 2 To connect the wires to the IPS RDPE 2 refer to Figure 3 or to the label attached to the inside lid of the data port box and do the following a Connect the power wires from the power supply to the 24 VAC IN positions on the power connector of the IPS RDPE 2 WARNING Turn off power to the power supply before wiring the power to the IPS RDPE 2 b Connect the wires cable from the controller at the head end to either the FROM CONTROLLER connector D or P control BNC VIDEO OUT connector Coaxitron control or UTP VIDEO OUT connector UTP control of the IPS RDPE 2 C2473M C 8 06 POLE MOUNTING 1 Install the PA402 mount adapter Refer to the instructions supplied with the adapter 2 Open the lid of the IPS RDPE 2 box Install two 3 4 inch 1 91 cm conduit fittings not supplied Close the lid of the IPS RDPE 2 box 3 Attach the IPS RDPE 2 to the PA402 and secure with the hardware supplied with the mount adapter Refer to F
4. or ExSite system The IPS RDPE 2 features an RJ 45 port that provides a communication interface between Pelco s positioning systems and a Windows based PC Palm OS compatible handheld or iPAQ pocket PC Pelco s serial interface cable IPS CABLE is required for data transmission REQUIRED ACCESSORIES One of the following accessory options not supplied is required to view video control pan tilt zoom or upload revised operating software and language files using an IPS RDPE 2 OPTION 1 e Operating software e PS RMK remote monitor kit Kit includes a 5 9 inch TFI LCD monitor Palm OS compatible handheld with serial cable and an IPS CABLE OPTION 2 e Operating software version 1 2 or higher e PS CABLE serial interface cable e Windows based PC Palm OS compatible handheld or iPAQ pocket PC not available through Pelco e Serial interface connectors and matching connections for the PC Palm OS compatible handheld or iPAQ pocket PC not available through Pelco e Hand held monitor not available through Pelco NOTE To upload software the following system software must be installed e Spectra lll dome drive must have software version 1 2 or higher installed e ExSite explosionproof system must have software version 1 13 or higher installed Software cannot be uploaded to an Esprit system C2473M C 8 06 5 Mounting Instructions WALL MOUNTING 1 Open the lid of the IPS RDPE 2 box Install two 3 4 inch 1 91 c
5. the RJ 45 port in the IPS RDPE 2 The audible alert will stop To service and or test the positioning system refer to the manual supplied with IPS CABLE The IPS CABLE manual includes instructions for on site setup testing and software uploads using the RJ 45 port of the IPS RDPE 2 with a Windows based PC Palm OS compatible hand held or iPAQ pocket PC WARNING To prevent damage to the positioning system never cycle power or attempt control of the system during the upload process The upload process is not complete until the system reboots NOTE During software language file upload an icon will appear on the monitor at the head end to indicate data is being transferred to the positioning system refer to Figure 12 The default setting for data transmission is 115 2 kb per second Noisy and long run connections will slow the transmission rate When servicing testing is completed disconnect the IPS CABLE The audible alert is triggered Close the door to the IPS RDPE 2 to stop the audible alert and return control to the head end Figure 12 Upload Icon Specifications ELECTRICAL Input Voltage Power Consumption MECHANICAL Construction Finish Cable Entry Mount Method Latch GENERAL Environment Operating Range Weight Dimensions Rating 24 VAC 1 VA Does not include power required for positioning system Aluminum Gray polyester powder coat Two hole plugs will accommodate 3 4 inch 1 91
6. INSTALLATION OPERATION IPS RDPE 2 Remote Data Port 2473 8 06 Contents Important Safety Instructions Description Required Accessories Mounting Instructions Wall Mounting Pole Mounting Cable Wire Requirements and Connector Locations eens Wiring Diagrams Specifications List of Illustrations 1 2 Mounting to Pole with PA402 IPS RDPE 2 Connections 4 5 6 5 422 D or P Protocol Con 7 RS 422 D or P Protocol Con 8 5 422 D or P Protocol Con 9 5 422 D or P Protocol Con 10 RS 422 D or P Protocol Con 11 RS 422 D or P Protocol Con 12 Uploadicon 13 IPS RDPE 2 Dimension Drawi C2473M C 8 06 Motinting to Ditt rent Wall enn eater taceo RA SAIS eames S efe ndis Coaxitron Controller with te pen DRE OR Eg wea E E Nd Coaxitron Controller with UTP Video Passive Receiver Only 1 roller with Coax Video Point to Point Configuration liliis esses 1 roller with Coax Video Home Run Configuration 0 0 1 roller with Coax Video Daisy Chain Configuration
7. Passive Receiver Only RS 422 D or P Protocol Controller with Coax Video Point to Point Configuration Run Configuration Configuration RS 422 D or P Protocol Controller with UTP Video Point to Point Configuration Run Configuration Daisy Chain Configuration Refer to Figures 4 through 11 and select the desired configuration for your installation Make all equipment connections as illustrated in the drawings PTZ CONTROL AND SOFTWARE UPLOAD POSITIONING SYSTEM NN uw PTZ CONTROL ONLY IPS RDPE 2 RX RX TX UTP UTP UTP UTP VIDEO VIDEO IN OUT Hi SUPPLY VIDEO IN COAXITRON CONTROLLER Figure 4 Coaxitron Controller with Coax Video NOTES 2473 8 06 Input power for the IPS RDPE 2 is 24 VAC only The maximum wire gauge allowed for power input and output is 12 AWG Refer to the manual supplied with the positioning system for wiring distances and coaxial cable requirements PTZ CONTROL AND SOFTWARE UPLOAD POSITIONING SYSTEM VC UTP UTP UTP IPS RDPE 2 RX RX TX TX UTP UTP RX RX TX TX UTP UTP UTP UTP COAXITRON CONTROLLER VIDEO VIDEO IN OUT TO POWER SUPPLY Figure 5 Coaxitron Controller with UTP Video Passive Receiver Only NOTES Input power for the IPS RDPE 2 is 24 VAC only
8. SOFTWARE UPLOAD IPS RDPE 2 RX TX Ban UTP UTP UTP UTP TO POWER SUPPLY TX TX RX RX UTP UTP UTP RECEIVER AT CONTROL SYSTEM CONTROL SYSTEM Figure 9 RS 422 D or P Protocol Controller with UTP Video Point to Point Configuration NOTES e Input power for the IPS RDPE 2 is 24 VAC only The maximum wire gauge allowed for power input and output is 12 AWG e maximum wire gauge allowed for UTP is 16 AWG e Refer to the manual supplied with the back box for wiring distances and coaxial cable requirements C2473M C 8 06 PTZ CONTROL AND SOFTWARE UPLOAD POSITIONING SYSTEM VC UTP UTP UTP PTZ CONTROL AND ga SOFTWARE UPLOAD IPS RDPE 2 RX RX TX TX UTP UTP TO POWER SUPPLY POSITIONING SYSTEM VC UTP UTP UTP UTP RECEIVER POWER UTP UTP TX TX RX RX e CONTROL SYSTEM AT CONTROL SYSTEM IPS RDPE 2 UTP UTP UTP RECEIVER AT CONTROL SYSTEM RX RX TX TX RX RX TX TX UTP UTP UTP UTP SUPPLY Figure 10 RS 422 D or P Protocol Controller with UTP Video Home Run Configuration NOTES Input power for the IPS RDPE 2 is 24 VAC only The maximum wire gauge allowed for power input and output is 12 AWG The maximum wire gauge allowed for UTP is 16 AWG Refer to the manual supplied with the positioning system for wiring distances and coaxial cable requirements
9. The maximum wire gauge allowed for power input and output is 12 AWG The maximum wire gauge allowed for UTP is 16 AWG Refer to the manual supplied with the positioning system for wiring distances and coaxial cable requirements C2473M C 8 06 PTZ CONTROL AND SOFTWARE UPLOAD POSITIONING SYSTEM OR ti uy PTZ CONTROL ONLY IPS RDP UTP UTP RX RX TX TX UTP UTP VIDEO VIDEO IN OUT SUPPLY TX TX RX RX VIDEO IN CONTROL SYSTEM AT CONTROL SYSTEM Figure 6 RS 422 D or P Protocol Controller with Coax Video Point to Point Configuration NOTES e Input power for the IPS RDPE 2 is 24 VAC only The maximum wire gauge allowed for power input and output is 12 AWG The maximum wire gauge allowed for two wire communication is 16 AWG e Refer to the manual supplied with system for wiring distances and coaxial cable requirements 2473 8 06 11 PTZ CONTROL AND SOFTWARE UPLOAD POSITIONING SYSTEM PTZ CONTROL ONLY IPS RDPE 2 UTP UTP RX RX TX TX UTP UTP POWER SUPPLY 24 VAC 24 VAC 24 VAC 24 VAC PTZ CONTROL AND SOFTWARE UPLOAD POSITIONING SYSTEM H AT CONTROL SYSTEM AT CONTROL SYSTEM CONTROL SYSTEM OR ipe gt uy PTZ CONTROL ONLY IPS RDPE 2 UTP UTP UTP UTP RX RX TX TX RX RX TX TX TEENE 5 a a
10. a POWER VIDEO VIDEO SUPPLY IN Figure 7 RS 422 D or P Protocol Controller with Coax Video Home Run Configuration NOTES e Input power for the IPS RDPE 2 is 24 VAC only The maximum wire gauge allowed for power input and output is 12 AWG The maximum wire gauge allowed for two wire communication is 16 AWG e Refer to the manual supplied with the positioning system for wiring distances and coaxial cable requirements 12 C2473M C 8 06 PTZ CONTROL AND SOFTWARE UPLOAD PTZ CONTROL ONLY SOFTWARE UPLOAD PTZ CONTROL AND me POSITIONING SYSTEM PTZ CONTROL ONLY w IPS RDPE 2 UTP UTP UTP UTP VIDEO VIDEO IN OUT TO POWER SUPPLY 9 POSITIONING SYSTEM TX TX RX RX VIDEO IN CONTROL SYSTEM AT CONTROL SYSTEM g AT CONTROL SYSTEM m gt IPS RDPE 2 RX RX TX TX RX RX TX TX UTP UTP UTP UTP 5 5 E sil VIDEO VIDEO SUPPLY Figure 8 RS 422 D or P Protocol Controller with Coax Video Daisy Chain Configuration NOTES Input power for the IPS RDPE 2 is 24 VAC only The maximum wire gauge allowed for power input and output is 12 AWG The maximum wire gauge allowed for two wire communication is 16 AWG Refer to the manual supplied with the positioning system for wiring distances and coaxial cable requirements POSITIONING SYSTEM VC UTP POWER UTP UTP PTZ CONTROL AND
11. ble from the controller at the head end to either the FROM CONTROLLER connector D or P control BNC VIDEO OUT connector Coaxitron control or UTP VIDEO OUT connector UTP control of the IPS RDPE 2 2473 8 06 7 Cable Wire Requirements and Connector Locations Refer to Figure 3 for a layout of the data port box connectors It is important to connect all four communication wires from the IPS RDPE 2 to the Spectra dome system or ExSite system It will not be possible to perform software and language file uploads if the transmit and receive wires are not connected Ne PS CRRAE RR TO POSITIONING FROM SYSTEM CONTROLLER nana nnn CAMERA CONTROLLER EERE 24 VAC POWER 24 VAC 007 24 VAC OUT 24 VAC IN 24 VAC IN POSITIONING SYSTEM CONNECTIONS FROM CAMERA TO CONTROLER NWXS WN NNOXSS DOT Figure 3 IPS RDPE 2 Connections NOTES e Input power for the IPS RDPE 2 is 24 VAC only e maximum wire gauge allowed for power input and output is 12 AWG e maximum wire gauge allowed for two wire communication and UTP is 16 AWG C2473M C 8 06 Wiring Diagrams The IPS RDPE 2 is designed to work in both coaxial cable and unshielded twisted pair UTP video transmission systems Installation configurations include the following Coaxitron Controller with Coax Video Coaxitron Controller with UTP Video
12. cm conduit fittings not supplied Four 0 375 inch 0 95 cm holes on mounting plate One stainless steel link lock latch secured with screw latch also can be secured with padlock not supplied Indoor outdoor 40 to 158 F 40 to 70 C 2 41 Ib 1 09 kg See Figure 13 Meets NEMA Type 4X standards Design and product specifications subject to change without notice 7 32 18 8 NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES Figure 13 IPS RDPE 2 Dimension Drawing C2473M C 8 06 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FR FT FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products hree years on Genex Series products multiplexers server and keyboard hree years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty hree years on PMCL200 300 400 Series LCD monitors wo years on standard motorized or fixed focal length lenses wo years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spec
13. igure 2 IPS RDPE 2 CONDUIT FITTINGS Figure 2 Mounting to Pole with PA402 4 Run conduit with wiring from the positioning system to the IPS RDPE 2 To connect the wires to the IPS RDPE 2 refer to Figure 3 or to the label attached to the inside lid of the data port box and do the following a Connect the communication wires from the positioning system to the communication connector of the IPS RDPE 2 IMPORTANT Connect all four communication wires from the Spectra Ill dome system or ExSite system to the IPS RDPE 2 Transmission and receive wires must be connected to perform software and language file uploads b Connect the power wires from the positioning system to the 24 VAC OUT positions on the power connector of the IPS RDPE 2 c Connect the video wires cable from the positioning system to either the BNC VIDEO IN connector if using coaxial or UTP VIDEO IN connector if using UTP of the IPS RDPE 2 5 Run conduit with wiring from the power supply and wiring from the controller at the head end to the IPS RDPE 2 To connect the wires to the IPS RDPE 2 refer to Figure 3 or to the label attached to the inside lid of the data port box and do the following a Connect the power wires from the power supply to the 24 VAC IN positions on the power connector of the IPS RDPE 2 WARNING Turn off power to the power supply before wiring the power to the IPS RDPE 2 b Connect the wires ca
14. m conduit fittings not supplied Close the lid of the IPS RDPE 2 box Determine the mounting location for the IPS RDPE 2 Use the IPS RDPE 2 box as a template and mark the four fastener positions on the mounting surface Prepare the holes for installation Attach the IPS RDPE 2 securely with four fasteners of appropriate length Fasteners between 1 4 inch and 5 16 inch diameter can be used not supplied Refer to Figure 1 MOUNTING HARDWARE WITH WOOD SCREW MOUNTING ANCHOR OR TOGGLE BOLT NOT SUPPLIED HARDWARE NOT SUPPLIED NOT SUPPLIED DOOR LATCH DOOR LATCH DOOR LATCH RETAINING RETAINING RETAINING SCRI SCREW mm om CONDUIT CONDUIT CONDUIT FITTINGS FITTINGS M x FITTINGS WALLBOARD WALL CONCRETE WALL 6 7 Mounting to Wallboard Mounting to Wall Mounting to Concrete Figure 1 Mounting to Different Wall Types Run conduit with wiring from the positioning system to the IPS RDPE 2 To connect the wires to the IPS RDPE 2 refer to Figure 3 or to the label attached to the inside lid of the data port box and do the following a Connect the communication wires from the positioning system to the communication connector of the IPS RDPE 2 IMPORTANT Connect all four communication wires from the Spectra Ill dome system or ExSite system to the IPS RDPE 2 Transmis sion and receive wires must be connected to perform software and language file uploads
15. ogo Camclosure Esprit Genex Legacy ExSite and Spectra are registered trademarks of Pelco Spectra IIl Endura and ExSite are trademarks of Pelco Palm is a trademark of Palm Inc Windows is a registered trademark of Microsoft Corporation DLP is a registered trademark of Texas Instruments Inc iPAQ Pocket PC is a trademark of the Hewlett Packard Company Copyright 2006 Pelco All rights reserved Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
16. tra Esprit ExSite and PS20 scanners including when used in ontinuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades wo years except lamp and color wheel on Digital Light Processing DLP displays he lamp and color wheel will be covered for a period of 90 days The air filter is not covered under warranty Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product lia bility relating to the Products shall not exceed the price paid b
17. with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Green materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002 95 EC This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment emm REVISION HISTORY Manual Date Comments C2473 2 03 Original version C2473M A 1 03 Revised per ECO 03 9497 for software revision C2473M B 8 05 Added ExSite system information C2473M C 8 06 Revised figures 1 2 and 13 for new design and unit weight per ECO 05 12718 Pelco the Pelco l
18. y the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 p289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified
Download Pdf Manuals
Related Search