Pelco FR8301A Network Card User Manual
Contents
1. 9 3 Rear Panel of FT8301A Transmitter and FR8301A 10 4 Mounting the FT8301A Transmitter FR8301A Receiver Using the Wall Clip 13 5 FT8301A Transmitter 14 8301 Receiver Connections 15 List of Tables A Troubleshooting with Front Panel Indicators 16 C1679M 1 06 3 Important Safety Instructions 20 m SO ema SIS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has wo blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the points whe2. Red Incoming video signal Optical signal is not Refer to the Optic Fault LED isnot present onthe being received from troubleshooting section channel the transmitter Optic below Fault LED is also red Video source is not Check power connection to powered on the video source Video source is not Check BNC connections connected to the transmitter Coaxial cable Replace cable connected to the transmitter is defective Continued on next page 16 C1679M 1 06 Table A Troubleshooting with Front Panel Indicators Continued Indicator Color Possible Cause Corrective Action Optic Fault LED Transmitter not being received from the transmitter powered on Green Laser is operating action required properly Flashing red Laser has shut down Transmitter is Ensure that transmitter operating in extreme operates according to conditions for operating conditions stated example operating in the Specifications section temperature is below and then cycle the power If or above recommended problem persists contact range as stated in the Product Support the Specifications section Laser has reached end Cycle the power If problem of life persists contact Product Support Optic Fault LED Receiver Green The optical signal is action required being received from the transmitter Red The optical signal is Transmitter is not Check power connections
3. PHILLIPS amp WALL CLIP FLANGE PAN HEAD WITH LOCK WASHER 2 amp Figure 4 Mounting the FT8301A Transmitter FR8301A Receiver Using the Wall Clip C1679M 1 06 CONNECTIONS Connections to the FT8301A transmitter and the FR8302A receiver are made on the rear panel of the modules and consist of the following Power connection NOTES A12VDC or 24 VAC power supply can be used to power the transmitter receiver when used as a standalone module A 12 VDC power supply is provided If a 24 VAC power supply is used the power supply must be a Listed Direct Plug In Power Unit marked as Class 2 and rated as 24 VAC 200 mA minimum output In extreme temperature conditions it is recommended that industrial rated outdoor power supply such as the Pelco WCS1 4 power supply be used Fiber connection Video connection UTP or BNC NOTE When connecting to the UTP connector it is recommended that solid UTP wire rather than stranded UTP wire be used If stranded UTP wire is used it is recommended that you tin the stranded wire Figure 5 illustrates 01 transmitter connections Figure 6 illustrates FR8301A receiver connections 4 POWER ALARM CONNECTION FOR RACK MOUNTED MODULE POWER CONNECTION Hm FOR STANDALONE MODULE E M FIBER OPTIC CABLE _ oOo OCOC OOL UTP WIRES OR Eo COAXIAL CABLE Figure 5 FT8301A Transmitter Co
4. Replace power supply if necessary Fiber optic cable is not connected Check fiber optic connections Fiber optic cable connectors are dirty or are damaged Clean polish or replace fiber optic cable connectors as necessary Fiber optic cable is defective Replace cable A problem exists with he optical power budget Verify that losses in fiber optic cable do not exceed the optical power budget specification of the fiber optic link If the losses do exceed the optical power budget contact Product Support C1679M 1 06 Specifications VIDEO Number of Channels Modulation Type Video Input 8301 Video Output FR8301A Bandwidth Gain Differential Gain Differential Phase Tilt Signal to Noise Ratio GENERAL Operating Temperature Input Power Requirements LED Indicators Dimensions Unit Weight MECHANICAL Connectors Video Rack Power Alarm Standalone Power Fiber Optic 1 Pulse code modulation 8 bit resolution BNC 1 0 Vp p 75 ohms or UTP 100 ohms NTSC PAL and SECAM 6 5 MHz Unity lt 2 1 196 60 dB CCIR weighted 40 to 167 F 40 to 75 C 12 VDC or 24 VAC 170 mA Power Video Present Optic Fault 85 D x 1 08 W x 4 81 H 22 23 x 2 74 x 12 22 cm 1 54 Ib 0 70 kg BNC UTP 2 pin connector spring cage terminal 4 pin connector 2 pin connector screw terminal ST for multimode fiber ST or FC for si
5. energy and if not installed and used in ruction manual may cause harmful interference to radio communications Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission s rules This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada C1679M 1 06 Product Overview DESCRIPTION The FT8301A FR8301A fiber transmitter and receiver provide the ability to transmit one composite video channel over one optical fiber refer to Figure 1 ONE ONE VIDEO VIDEO I FT8301A COMPATIBLE 2 TRANSMITTER ONE RECEIVER FIBER ONE ONE VIDEO VIDEO diei COMPATIBLE FR8301A 22 1 TRANSMITTER ONE RECEIVER FIBER Figure 1 Single Channel Video FT8301A Transmitter and FR8301A Receiver In addition to compatibility with each other the FT8301A transmitter and the FR8301A receiver are compatible with other fiber models The FT8301A transmitter is compatible with the FR8302A receiver and is also backward compatible with the FR8301 receiver In addition to compatibility with the rack mountable FT8301A transmitter discussed in this manual the FR8301A receiver is compatible with the miniature FT8301A transmitter and is also backward compatible with the FT8301 transmitter Features of the FT8301A FR830 8 bi
6. module slots and a power supply RK5000 3U rack mount chassis provides 14 module slots a power supply is not included Power to the modules can be supplied using the optional external power supply EPS5000 120 For additional information refer to the RK5000PS 3U RK5000 3U Fiber Rack Mount Chassis Installation manual RK5000PS 5U Designed to accommodate Endura modules but can also accommodate fiber optic modules with the use of the RK5001 1UEXP adapter kit The RK5001 1UEXP adapter kit is required for installation of the FT8301A transmitter FR8301A receiver into the RK5000PS 5U chassis For information about the RK5000PS 5U chassis refer to the RK5000PS 5U Rack Mount Chassis Installation manual C1679M 1 06 11 MOUNTING THE TRANSMITTER RECEIVER TO A WALL The FT8301A transmitter FR8301A receiver can be mounted to a wall in the fol Using the supplied wall clip for attachment of a single module to a wall lowing ways For installation instructions refer to the Mounting the Transmitter Receiver Using the Wall Clip section Using the optional WM5001 wall mount kits which are designed for mou nting of single width fiber optic modules The WM5001 3U base kit allows mounting of a single module to the wall The WM5001 3UEXP expansion kit allows mounting of an additional module It is recommended that a maximum of three expansion kits be used with the base kit allowing a maximum of four single width modu
7. or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clovis CA 93612 5699 USA South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 REVISION HISTORY Manual Date Comments C1679M 1 06 Original version Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco Copyright 2006 Pelco DLP is a registered trademark of Texas Instruments Inc All rights reserved PELCO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
8. INSTALLATION FT8301A FR8301A Fiber Transmitter and Receiver Single Channel Digitally Encoded Video C1679M 1 06 Contents Important Safety 5 8 4 Regulatoryi Notices 5 VERE RUE I VE Va petendi a tena 6 Product OVBIVIGW r tte tt Nette Ht En Rule alle tite dtp ette sare uud 7 DOSCHIPLON es dert tricis obs verunt d Cd dan AN ita Pa ae eA 7 Models euet rm 8 Optional 8 Front 9 ee eee cigar de tans WE DUAE BILD 10 Installation ei at ad ese oon Sai dave Da eR o adr Reed bie wales 1 Package Gontents vas SEDE ee RE ERRARE IE PRIEST A RERUM ees 1 MOUDEI saa e trees tenor Ot SIR DER ode AR beo euis Reb a Ret d 11 Mounting the Transmitter Receiver into a 1 Mounting the Transmitter Receiver to a 2 OR 14 Troubleshooting e 16 Specifications s ce Mati Me waded elaine a DEUS 8 List of Illustrations 1 Single Channel Video FT8301A Transmitter and FR8301A Receiver 7 2 Front Panel of FT8301A Transmitter and FR8301A Receiver
9. f third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state Pa If a warranty repair is required the Dealer must contact Pelco at 800 p289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information Model and serial number 2 Date of shipment PO number Sales Order number or Pelco invoice number 3 Details of the defect or problem there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 2096 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii
10. hassis C1679M 1 06 FRONT PANEL The front panel of the FT8301A transmitter and the FR8301A receiver provides LED indicators that allow you to monitor signal status laser status and operating power refer to Figure 2 0 0 20000000 7909090909 8301 FR8301A TRANSMITTER RECEIVER Figure 2 Front Panel of FT8301A Transmitter and FR8301A Receiver o VIDEO PRESENT LED 2 OPTIC FAULT LED 3 POWER LED Pelco badge For detailed information about the front panel indicators refer to the Troubleshooting section C1679M 1 06 REAR PANEL Connections to the FT8301A transmitter and FR8301A receiver are made to the rear panel of the modules refer to Figure 3 FT8301A FR8301A TRANSMITTER RECEIVER Figure 3 Rear Panel of FT8301A Transmitter and FR8301A Receiver RACK POWER ALARM CONNECTOR 4 pin connector for power alarm connection of rack mounted module STANDALONE POWER CONNECTOR 2 pin connector for power connection of standalone module removable mating connector with screw terminals not shown FIBER OPTIC CONNECTOR ST or FC dependent on FT8301A FR8301A model UTP UNSHIELDED TWISTED PAIR CONNECTOR 100 ohm differential analog video input FT8301A output FR8301A 2 pin connector removable mating connector with spring cage terminals not shown o BNC CONNECTOR 75 ohm analog
11. l only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so 01679 1 06 The product and or manual may bear the following marks AN This symbol indicates that dangerous voltage constituting a risk of electric shock is present CAUTION su dnd RISK OF ELECTRIC SHOCK AN This symbol indicates that there are important DO NOT OPEN operating and maintenance instructions in the literature accompanying this unit C1679M 1 06 5 Regulatory Notices This devi ce complies wi conditions 1 this devic interfere nce received in h Part 15 of the FCC Rules Operation is subject to the following two e may not cause harmful interference and 2 this device must accept any cluding interference that may cause undesired operation RADIO AND TELEVISION INTERFERENCE This equi pursuant pment has bee n tested and found to comply with the limits of a Class A digital device to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipme accordance with the ins Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense nt generates uses and can radiate radio frequency
12. les to be mounted to the wall NOTE The WM5001 wall mount kits can be used with the WM5002 wall mount kits which are designed for mounting of double width fiber optic modules If mounting a mix of single width and double width modules is desired it is recommended that a maximum of two single width modules and one double width module be mounted in combination with one another For mounting instructions using the wall mount kits refer to the WM500 Kit Installation manual 0 Series Wall Mount Mounting the Transmitter Receiver Using the Wall Clip NOTE Before mounting the FT8301A transmitter FR8301A receiver to a wall adequate space at both ends for viewing the front panel LEDs and for making cable connections To attach the FT8301A transmitter FR8301A receiver to a wall using the suppl Figure 4 and do the following 1 Using the two vertical or horizontal wall mounting holes attach the wal two screws not provided ensure that there is he various rear panel ied wall clip refer to clip to a wall using 2 Slide the module into the clip until the two holes on the bottom of the m two holes on the lower flange of the clip odule align with the 3 Attach the module to the clip using the two Phillips pan head screws provided for the clip C1679M 1 06 lt FLANGE Q VERTICAL MOUNTING HOLE 2 Q amp HORIZONTAL MOUNTING HOLE 2 TRANSMITTER RECEIVER 4 LOWER SCREW
13. letter C The conformal coated version of FT8301AMSTR for example is CT8301AMSTR For models with higher optical power budgets contact the factory C1679M 1 06 19 OPTICAL POWER BUDGET TRANSMISSION DISTANCE AND LASER CLASS 1 LIMIT FR8301A RECEIVER AND COMPATIBLE TRANSMITTERS The conformal coated version of FR8301AMSTR for example is CR8301AMSTR For models with higher optical power budgets contact the factory Optical Maximum Laser FR8301A Compatible Power Transmission Class 1 Receiver Transmitters Wavelength Budget Distance Limit Multimode 62 5 125 FR8301AMSTR FT8301 AMSTR 850 nm 20 dB 2km 12mi 0 78 mW FT8301 AMST FT8301MST Multimode Extended Distance 62 5 125 um FR8301AMSTRE FT8301 AMSTRE 1310 nm 2648 6km 37 mij 15 6 mW FT8301AMSTE FT8301MSTE Single Mode 9 125 FR8301ASSTR FT8301ASSTR 1310 nm 28dB 46 km 28 6 mif 15 6 mW FT8301 ASST FT8301SST FR8301ASFCR FT8301ASFCR 1310 nm 28dB 46 km 28 6 mif 15 6 mW FT8301ASFC FT8301SFC The FR8301A receiver and compatible transmitters are classified by the FDA as Class 1 laser products When using 50 125 um multimode fiber subtract 3 dB from the optical power budget Maximum transmission distance is limited by fiber bandwidth Maximum transmission distance is based on attenuation of 0 5 dB km plus a 5 dB buffer for connector and splice losses NOTES For confo
14. ngle mode fiber C1679M 1 06 OPTICAL POWER BUDGET TRANSMISSION DISTANCE AND LASER CLASS 1 LIMIT FT8301A TRANSMITTER AND COMPATIBLE RECEIVERS Optical Maximum Laser FT8301A Compatible Power Transmission Class 1 Transmitter Receivers Wavelength Budget Distance Limit Multimode 62 5 125 FT8301AMSTR FR8301AMSTR 850 nm 20 4 2 km 1 2 mi 0 78 mW FR8302AMSTR 2 FR8301MSTR 850 nm 15 dBt 2 km 1 2 mij 0 78 mW Multimode Extended Distance 62 5 125 FT8301 AMSTRE FR8301 AMSTRE 1310 nm 26 dB 6 km 3 7 mi 15 6 mW FR8302AMSTRE 2 FR8301MSTRE 310 nm 20 4 6 km 3 7 mi 15 6 mW Single Mode 9 125 FT8301ASSTR FR8301ASSTR 310 nm 28dB 46 km 28 6 15 6 mW FR8302ASSTR 2 FR8301SSTR 310 nm 20 dB 30 km 18 6 15 6 mW FT8301ASFCR FR8301ASFCR 310 nm 28dB 46 km 28 6 15 6 mW FR8302ASFCR 2 FR8301SFCR 310 nm 20 dB 30 km 18 6 15 6 mW The FT8301A transmitter and compatible receivers are classified by the FDA as Class 1 laser products When using 50 125 um multimode fiber subtract 3 dB from the optical power budget Maximum transmission distance is limited by fiber bandwidth Maximum transmission distance is based on attenuation of 0 5 dB km plus a 5 dB buffer for connector and splice losses NOTES For conformal coated models replace the first letter F in the model number with the
15. nnections 14 C1679M 1 06 C1679M 1 06 POWER ALARM CONNECTION FOR RACK MOUNTED MODULE POWER CONNECTION FOR STANDALONE MODULE t m FIBER OPTIC CABLE UTP WIRES OR lt Sm ceu Figure 6 FR8301A Receiver Connections Troubleshooting LED indicators on the front panel of the FT8301A transmitter FR8301A receiver refer to Figure 2 allow you to monitor signal status laser status and operating power Table A provides information about the front panel indicators and associated troubleshooting guidelines Table A Troubleshooting with Front Panel Indicators Indicator Color Possible Cause Corrective Action Power LED Pelco badge Blue Pelco logo lights Power is being applied to the module 0 action required Blue Pelco logo does not light Power is not being applied to the module Power connection is faulty Check power connection f module is rack mounted reseat module or power supply as necessary Power supply has failed Replace power supply Loss of power occurs due to tripped circuit breaker s blown fuse s or faulty electrical service Check circuit breaker s use s or electrical service as necessary Video Present LED Green Incoming video signal No action required is present on the channel
16. re they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Installation should be done only by qualified personnel and conform to all local codes Unless the unit is specifically marked as a NEMA Type 3 3R 35 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture Use only installation methods and materials capable of supporting four times the maximum specified load A CCC approved power cord must be used to power this equipment when used in China CAUTION These servicing instructions are for use by qualified service personne
17. rmal coated models replace the first letter Fin the model number with the letter C 20 C1679M 1 06 C1679M 1 06 This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment 21 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard e Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Three years on PMCL 200 300 400 Series LCD monitors Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications e Two years on Esprit and WW5700 Series window wiper excluding wiper blades Two years except lamp and color
18. smission FI8301AMSTRE Single channel fiber optic video transmitter multimode ST connector FR8301AMSTRE Single channel fiber optic video receiver distance up to 6 km extended distance Single Mode Models FR8301ASSTR Single channel fiber optic video receiver FR8301ASFCR Single channel fiber optic video receiver For conformal coated models replace the first letter F in the mo The conformal coated version of FT8301AMSTR for example is OPTIONAL ACCESSORIES The following optional accessories are available WM5001 3U Wall mount base kit for single width mo transmission distance up to 6 km extended distance multimode ST connector transmission FT8301ASSTR Single channel fiber optic video transmitter single mode ST connector single mode ST connector FT8301ASFCR Single channel fiber optic video transmitter single mode FC connector single mode FC connector del number with the letter C CT8301AMSTR dule WM5001 3UEXP Wall mount expansion kit single width module RK5000 3U 19 inch rack mount chassis for 14 slots no power 3 RUs RK5000PS 3U 19 inch rack mount chassis for 12 slots with power 3 RUs EPS5000 120 External rack power supply 1 RU dual 120 W power outputs RK5001B 3U Blank filler panel single width RK5002B 3U Blank filler panel double width RK5001 1UEXP Adapter kit that allows a 3 RU single width fiber module to be used in RK5000PS 5U rack mount c
19. t digitally encoded video for high quality video transmission over a single fiber 1A fiber optic transmission system include the following Multimode fiber support for distances up to 6 km 3 7 mi Single mode fiber support for distances up to 46 km 28 6 mi Exceeds all requirements for the RS 250C Medium Haul Transmission specification Compatible with NTSC PAL and SECAM video standards Designed to meet NEMA TS 2 and Caltrans traffic signal control equipment standards for ambient operating temperature mechanical shock and vibration humidity with condensation high line low line voltage conditions and transient voltage protection NOTE Conformal coating is required for operation in environments with relative humidity above 95 condensing No performance adjustments required 12 VDC or 24 VAC power supply LED indicators for monitoring of signal status laser status and operating power The FT8301A transmitter FR8301A receiver is a Class 1 laser product that complies with FDA radiation performance standard 21CFR Subchapter J and with IEC 60825 1 Edition 1 2 2001 08 C1679M 1 06 MODELS The FT8301A FR8301A fiber transmitter and receiver consist Multimode Models of the following series of models FT8301AMSTR Single channel fiber optic video transmitter multimode ST connector transmission distance up to 2 km FR8301AMSTR Single channel fiber optic video receiver distance up to 2 km multimode ST connector tran
20. video input FT8301A output FR8301A NOTE The FT8301A transmitter FR8301A receiver provides two video connectors UTP connector and one BNC connector Only one of the connectors can be used at one time For additional information about rear panel connections refer to the nstallation section C1679M 1 06 Installation PACKAGE CONTENTS The following items are supplied 1 FT8301A transmitter or FR8301A receiver 1 Regulated switching power supply with four plug adapters North American Australian U K and European configurations 100 240 VAC 50 60 Hz input 12 VDC output 1 Wallclip with two 4 40 x 250 inch Phillips pan head screws with lock washers for attachment of single module to wall 1 FT8301A FR8301A Fiber Transmitter and Receiver Installation manual this manual MOUNTING The FT8301A transmitter FR8301A receiver can be mounted into a rack or can be used as a standalone module As a standalone module the unit can be placed on a desktop or can be mounted to a wall MOUNTING THE TRANSMITTER RECEIVER INTO A RACK The FT8301A transmitter FR8301A receiver can be installed into an RK5000 Series rack mount chassis which can be mounted into an industry standard 19 inch 48 26 cm equipment rack The RK5000 Series rack mount chassis includes the following models RK5000PS 3U and RK5000 3U Designed to accommodate fiber optic modules as follows RK5000PS 3U rack mount chassis provides 12
21. wheel on Digital Light Processing DLP displays The lamp and color wheel will be covered for a period of 90 days The air filter is not covered under warranty Eighteen months on DX Series digital video recorders NVR300 Series network video recorders Endura Series distributed network based video products and TW3000 Series twisted pair transmission products e One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products hall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential amages including loss of use loss of profit and claims o
Download Pdf Manuals
Related Search