Pelco CC3700H-2X Camcorder User Manual
Contents
1. without lens 1 3 inch 510 H x 492 V 768 H x 494 V 6mm diagonal AC line lock or internal oscillator 330 TV lines 480 TV Lines Electronic passive 0 5 lux at 50 IRE f1 2 with 80 scene reflection 0 7 lux at 50 IRE f1 2 with 80 scene reflection 52 dB AGC Off Automatic Adjustable 0 120 Selectable by DIP switch setting Selectable by DIP switch setting 525 lines 2 1 interlace DSP DC video control 1 Vp p 75 ohms 1 60 to 1 100 000 second 2500 9500 K 11 40 VDC or 14 30 VAC Less than 6 5 watts 2 pin terminal strip push in type with screw lock BNC 4 pin connector miniature square C CS mount adjustable Use 1 4 20 screw top or bottom of camera housing 14 to 122 F 10 to 50 C 14 to 158 F 10 to 70 C 2 48 W x 2 67 H x 4 33 D inches 6 3 x 6 8 x 11 cm 0 77 lb 0 35 kg Design and product specifications subject to change without notice Pelco Manual C1986M B 11 03 15 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on Pelco manufactured cameras CC3500 CC3600 CC3700 and MC3500 MC3600 Series two years on all other cameras Three years on Genex Series multiplexers server and keyboard and 090 Series Camclosure Camera System Two y2. PELLO Installation Operation CC3700 Series Color Camera C1986M B 11 03 LISTED Pelco World Headquarters 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 2 Pelco Manual C1986M B 11 03 CONTENTS IMPORTANT SAFEGUARDS AND WARNINGS Regulatory Notices DESCRIPTION Models CAMERA LAYOUT isc ea 6 INSTALLATION pia 6 Lens Mounting Camera Mounting POWER AND VIDEO CONNECTIONS III au nia 8 EENS SETUP AND FOCUS PROCEDURES cccisnssicccccsspssasccrssasesccccsenstiaeratnpsicecarensstasecrtsgnedacensunstaconetanaieararttsatcdes 10 BACK FOCUS ADJ USTMEN T ccoo 11 SWITCHASETTIN OS cias 12 CAMERA SYNCHRONIZATION UL sara oir 14 SPECIFICATIONST u L as 15 WARRANTY AND RETURN INFORMATION LLL LIL nata 16 LIST OF ILLUSTRATIONS Figure 1 Camera Layout Figure 2 AID AIV Lens Connector Figure 3 Camera Mounting Figure 4 Power Supply Connections Figure 5 AGC and ESC Switch Settings Figure 6 Back Focus Adjustment Figure 7 Switch Settings LIST OF TABLES Table A Recommended Wire Gauge and Wiring Distances Table B Video Coaxial Cable Requirements Pelco Manual C1986M B 11 03 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product the following WARNINGS should be observed 1 Read these instructions Keep these instruc
3. ct a camera and synchronize it to the reference camera by turning the phase adjustment control clock wise and or counterclockwise 3 Each time an adjustment is made switch back and forth between the camera you are adjusting and the refer ence camera Repeat this process as many times as necessary until the roll between the cameras is no longer noticeable 4 Adjust the phase of all other cameras by repeating steps 2 through 3 Always adjust to the reference camera selected in step 1 NOTE The preferred method for camera phase adjustment is to use a dual trace oscilloscope to align the vertical sync pulses of the reference camera to the selected camera s 14 Pelco Manual C1986M B 11 03 SPECIFICATIONS GENERAL CCD Sensor Picture Elements CC3700S 2 CC3700H 2 Sensing Area Synchronization System Horizontal Resolution CC3700S 2 CC37005 2X CC3700H 2 CC3700H 2X Iris Control Minimum Illumination CC3700S 2 CC37005 2X CC3700H 2 CC3700H 2X Signal to Noise Ratio Gain Control Vertical Phase Automatic Gain Control Backlight Compensation Scanning System Signal Processing Auto Iris Lens Type Video Output lris Control Range Auto White Balance Range ELECTRICAL Power Requirements Power Consumption Power Connector Video Connector Lens Jack MECHANICAL Lens Mount Camera Mount ENVIRONMENTAL Operating Temperature Storage Temperature PHYSICAL Physical Dimensions Weight
4. cur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device many not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada DESCRIPTION The CC3700 Series is a compact color video camera with a 1 3 inch CCD imager All cameras have a direct drive auto iris lens connector and adjustable back focus and they accept C and CS lenses Models CC3700S 2 Standard resolution 330 TV lines SuperHAD CCD 0 5 lux 50 IRE f1 2 NTSC CC3700H 2 High res
5. d Ship to the appropriate address below f you are located within the continental U S Alaska Hawaii or Puerto Rico fyou are located outside the continental U S Alaska Hawaii or Puerto Rico Service Department Intermediate Consignee Ultimate Consignee Pelco American Overseas Air Freight Pelco 3500 Pelco Way 320 Beach Road 3500 Pelco Way Clovis CA 93612 5699 Burlingame CA 94010 Clovis CA 93612 5699 USA USA 0 Pelco the Pelco logo Spectra Genex Legacy Esprit and Camclosure are registered trademarks of Pelco TM HyperHAD and EXview HAD CCD are trademarks of the Sony Corporation Copyright 2002 Pelco All rights reserved REVISION HISTORY Manual Date Comments C1986M 3 02 Original version C1986M A 7 02 Revised the lens connector wiring chart C1986M B 8 02 Revised Important Safeguards and Warnings 11 03 Revised instructions for setting DIP switches to match Baxall version of manual
6. drive and auto iris lenses BLC will still function even though the Electronic Sensitivity Control feature is switched off Following are the BLC switch settings BLC Enables the BLC mode OFF Default setting Disables the BLC mode w O ANWAR NWA n mn Flickerless Switch Settings 4 3 and 1 The Flickerless setting can reduce the flicker caused by certain lighting conditions The Electronic Sensitivity Control setting must be off for correct operation of the Flickerless function Choose between the following settings FLK Enables the Flickerless mode OFF Default setting Disables the Flickerless mode n pL A NWA anwa Q T mn Pelco Manual C1986M B 11 03 13 CAMERA SYNCHRONIZATION When using more than one camera power supply a brief vertical roll may occur on the monitor when a camera view is switched To eliminate vertical roll adjust the phase control by synchronizing or line locking the cameras to one another Set the INT LL DIP switch to LL and use the phase potentiometer located on the side of the camera refer to Figure 1 to make adjustments It may be necessary to have two people in communication when synchronizing the cameras one person at the camera and another person at the monitor to observe the vertical roll and the effect of any adjustments made at the camera To synchronize the cameras do the following 1 Choosea reference camera to which all other cameras will be phased 2 Sele
7. ears on 100 150 200 and 300 Series Camclosure Camera Systems Two years on all standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM8500 CM9500 CM9740 CM9760 Matrix DF5 and DF8 Series Fixed Dome products Two years on Spectra Esprit and PS20 Scanners including when used in continuous motion applications Two years on Esprit and WW5700 series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no e
8. he Switch Settings section Switch setting is determined by the type of lens used Screw the lens onto the lens mount Be careful to prevent dust from entering the space between the lens and the CCD element If necessary use clean compressed air to remove any foreign matter Thread the lens cable through the cosmetic trim ring Connect the auto iris lens to the 4 pin iris drive connector located on the side of the camera Pin connections for the iris drive connector are as follows Pelco Manual C1986M B 11 03 3 4 PIN DC AID AUTO IRIS LENS VIDEO AIV AUTO IRIS LENS 1 Control coil negative Lens positive supply 2 Control coil positive Not used 1 2 3 Drive coil positive Video drive signal 4 Drive coil negative Ground Figure 2 AID AIV Lens Connector Camera Mounting Use a standard 1 4 20 screw provided with a maximum thread length of 3 8 inch 10 mm for top or bottom camera mounting The mount adapter may be fitted to the top or bottom of the camera The camera is shipped with the mount adapter located on the top of the camera To change the mount adapter position O Remove the four screws from the mount adapter located on the top of the camera 2 Remove the trim cover from the bottom of the camera by prying it loose Place the trim cover on the top of the camera where the mount adapter was removed Press into place 3 Install the mount adapter to the bottom of the camera Secure
9. l of the cameras the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras Table A Recommended Wire Gauge and Wiring Distances The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10 percent voltage drop Ten percent is generally the maximum allowable voltage drop for AC powered devices Wire Gauge Total 20 18 16 14 12 10 VA 0 5 mm 1 0 mm 1 5 mm 2 5 mm 4 0 mm 6 0 mm 10 283 451 716 1142 1811 2880 86 137 218 348 551 877 EXAMPLE A camera that requires 10 VA and is installed 283 feet 86 m from the transformer would require a minimum wire gauge of 20 AWG NOTE Distances are calculated in feet values in parentheses are meters Table B Video Coaxial Cable Requirements Cable Type Maximum Distance RG59 U 750 ft 229 m RG6 U 1 000 ft 305 m RG11 U 1 500 ft 457 m Minimum cable requirements 75 ohms impedance All copper center conductor All copper braided shield with 95 braid coverage Pelco Manual C1986M B 11 03 9 LENS SETUP AND FOCUS PROCEDURES Video Drive Auto Iris Lens When a video drive auto iris lens is used the lens mode selector switch must be set to AIV Switch the ESC and AGC OFF Refer to the lens instructions and adjust the lens for the optimum picture video output level of 1V peak to peak Swi
10. lens b Counterclockwise Moves the CCD sensor away from the back of the lens 3 When the back focus adjustment is satisfactory tighten the locking screws Do not over turn or force the back focus adjustment ring SE gao count BACK FOCUS ADJUSTMENT BACK FOCUS LOCKING SCREW ADJUSTMENT RING Figure 6 Back Focus Adjustment Pelco Manual C1986M B 11 03 11 SWITCH SETTINGS COLO PHASE LEVEL NOR OFF AIV INT ESC ESC BLC OFF NOTE White represents switch position Figure 7 Switch Settings Defaults NOTE Under most conditions no setting of switches will be required Please read the details of each switch before making any adjustments Gamma NORILIN Switch Switch Setting 8 Sets the Gamma level to one of the following NOR Default setting Increases visibility in dark areas of the picture 8 OE NOR LIN Linear response increases overall contrast 8 mO LIN Automatic Gain Control AGC Off Switch Switch Setting 7 Automatically adjusts the image to compensate for changes in light levels when us ing fixed or manual iris lenses Following are the AGC switch settings ON Default setting Enables the AGC mode 7 0 AGC ON OFF Disables the AGC mode 7 DI AGC OFF Lens Mode Selector AIV AID Switch Switch Setting 6 The AIV AID switch setting is determined by the type of lens used AIV Video drive auto iris lens 6 DI AIV AID Default
11. o not perform any servicing other than that contained in the operating instruc tions unless you are qualified to do so 16 Use only installation methods and materials capable of supporting four times the maximum specified load 17 Use only UL listed class 2 power supply 18 AID AIV Lens Connector The maximum load for a direct drive lens must not exceed 25 mA The maximum load for an auto iris lens must not exceed 50 mA The product and or manual may bear the following marks This symbol indicates that dangerous voltage constituting a risk of electric shock is present CAUTION within this unit RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol indicates that there are important operating and maintenance instructions in the lit erature accompanying this unit Please thoroughly familiarize yourself with the information in this manual prior to installation and operation 4 Pelco Manual C1986M B 11 03 REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio commu nications However there is no guarantee that the interference will not oc
12. olution 480 TV lines SuperHAD CCD 0 7 lux 50 IRE f1 2 with 80 scene reflection NTSC CC3700S 2X Standard resolution 330 TV lines SuperHAD CCD 0 5 lux 50 IRE f1 2 PAL CC3700H 2X High resolution 480 TV lines SuperHAD CCD 0 7 lux 50 IRE f1 2 with 80 scene reflection PAL Pelco Manual C1986M B 11 03 5 CAMERA LAYOUT BACK FOCUS ADJUSTMENT LOCKING MOUNT ADAPTER r PHASE ADJUSTMENT m LENS LEVEL ADJUSTMENT ncaa CONNECTOR ANG TRIM N IDN ADJUSTMENT RING BACK FOCUS BNC VIDEO CONNECTOR LENS CONNECTOR DIP SWITCHES COVER REMOVED Figure 1 Camera Layout NOTE The cosmetic trim ring conceals the LED light for more discreet surveillance operations The trim ring also hides the power connectors and protects the DIP switches INSTALLATION Lens Mounting The CC3700 Series camera can use fixed iris manual iris auto iris or direct drive lenses Cameras are factory set for CS mount lenses but easily adjust for C mount lenses 1 6 C Mount Lens Only Loosen the two back focus locking screws Rotate the back focus adjustment ring fully counterclockwise before installing the C mount lens refer to the section on Back Focus Adjustment Remove the cosmetic trim ring from the back of the camera refer to Figure 1 Set the lens mode selector switch on the side of the camera to AIV auto iris video drive lens or AID auto iris DC drive lens Refer to t
13. setting Direct drive lens 6 BIO AID Synchronization LL INT Switch Switch Setting 5 Locks the frame rate to the power supply frequency Eliminates vertical roll caused by multiple cameras connected to the same switching device Each camera output is synchronized to the frequency of the power supply Set the camera synchronization mode to one of the following Line Lock LL Default setting Line locks frame rate of cameras sO LL Internal INT Disables line lock use with DC power or noisy AC power 5 O INT 12 Pelco Manual C1986M B 11 03 Shutter Speed Selection Switch Settings 4 3 2 and 1 o o 1 250 1 1 000 1 4 000 1 125 1 500 1 2 000 1 10 000 NWA aNWa NWA ANWA NWA ANUAR NWA NWA 00014 ESC Electronic Sensitivity Control Switch Settings 4 3 and 1 The ESC feature compensates for an excessive light level by automatically adjust ing shutter speed Following are the ESC switch settings ESC Default setting Enables the Electronic Sensitivity Control mode OFF Disables the Electronic Sensitivity Control mode m O O KAAN AAEE x BNW NWA BLC Backlight Compensation Switch Settings 4 2 and 1 The BLC Backlight Compensation feature compensates for backlit scenes by enhancing objects in the center of the scene that would previously have been in silhouette BLC will only function with a manual iris lens when the Electronic Sensi tivity Control feature is switched on For direct
14. tch the AGC ON To focus fully open the iris by covering the lens with a suitable neutral density ND filter If the viewed scene is 6 5 feet 2 m away or farther set the lens focus to infinity far Use the back focus adjustment ring refer to the Back Focus Adjustment section and focus on the selected scene Remove the ND filter and set the lens focus as required Direct Drive DC Auto Iris Lens When a direct drive lens is used the lens mode selector switch must be set to AID Switch the ESC and AGC OFF Use an appropriate screwdriver to turn the lens level potentiometer refer to Figure 1 fully clockwise Next slowly adjust the potentiometer counterclockwise until the optimum picture is obtained video output level of 1V peak to peak Switch the AGC ON To focus fully open the iris by covering the lens with a suitable neutral density ND filter Select the scene to be viewed If the viewed scene is 6 5 feet 2 m away or farther set the lens focus to infinity far Use the back focus adjustment ring refer to the Back Focus Adjustment section and focus on the selected scene Remove the ND filter and set the lens focus as required Fixed Lens Set the ESC switch and AGC switch to ON To focus set the lens focus to infinity and view a scene greater than 6 5 feet 2 m away Focus the image with the back focus adjustment ring refer to the Back Focus Adjustment section Set the lens focus as required Manual Iris Lens Set the ESC s
15. tions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions o nN O oO A WO N Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Only use attachments accessories specified by the manufacturer 10 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the appara tus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 11 Referall servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture the apparatus does not oper ate normally or the apparatus has been dropped 12 Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 13 Warning To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture 14 Caution Danger of explosion if battery is replaced incorrectly Replace only with the same or equivalent type 15 To reduce the risk of shock d
16. vent will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise he above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide he following information Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with he product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepai
17. witch and AGC switch to ON To focus open the iris fully and set the lens focus to infinity View a scene greater than 6 5 feet 2 m away Focus the image with the back focus adjustment ring refer to the Back Focus Adjust mentsection Adjust the lens focus and set the iris for the best picture quality The largest aperture gives the best light sensitivity the smallest aperture the greatest depth of field Zoom Lens Set the lens focus to infinity far and fully open the iris by covering the lens with a suitable neutral density ND filter Zoom out to the widest field of vision and view a distant object Adjust the back focus adjustment ring until the object is in focus refer to the Back Focus Adjustment section Next zoom fully in and adjust the lens focus until the object is again focused Repeat these steps until the full zoom range may be viewed with the minimum loss of focus 4 O 4 ON TER AGC ON 3 DI Esc 3 mO OFF 7 OM AGC OFF A a DIP SWITCH SETTINGS WHITE REPRESENTS SWITCH POSITION Figure 5 AGC and ESC Switch Settings NOTE For best results outdoors use an ND3 filter 10 Pelco Manual C1986M B 11 03 BACK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case To adjust the back focus 1 Loosen the two back focus locking screws one on each side 2 Tum the back focus ring a Clockwise Moves the CCD sensor assembly towards the back of the
18. with the four screws removed in step 1 Figure 3 Camera Mounting Pelco Manual C1986M B 11 03 7 POWER AND VIDEO CONNECTIONS The CC3700 Series camera is designed to operate from a 12 VDC or 24 VAC power supply The power supply connections are shown in Figure 4 The LED on the back panel of the camera indicates that power is connected Use only a UL Listed Class 2 isolated power supply Power consumption is less than 6 5 watts UL LISTED UL LISTED CLASS 2 CLASS 2 ISOLATED ISOLATED POWER POWER SUPPLY SUPPLY Figure 4 Power Supply Connections To connect the camera power and video 1 Remove the rear cosmetic trim ring from the camera refer to Figure 1 Thread cabling through the trim ring 2 Connect the power cable to the two pin power connector on the back of the camera using the terminal block connector provided Refer to Table A for the recommended wire gauge and wiring distances 3 Connect a video cable to the SIGNAL OUT connector BNC on the back of the camera Refer to Table B for the type of video coaxial cable to use 4 Reattach the trim ring to the back of the camera 8 Pelco Manual C1986M B 11 03 AC Operation Only If you are wiring more than one camera to the same transformer connect one side of the transformer to the same terminal on all cameras and connect the other side of the transformer to the remaining terminal on all cameras Failure to connect al
Download Pdf Manuals
Related Search