Oricom 50 Baby Monitor User Manual
Contents
1. alarm beep sounds 797 7 recharging ha Note The parent unit can be used on or off the charger pod When on the charger pod the batteries will be recharged at the same time However the time it takes to charge the batteries to full will be longer when the unit is charged and used at the same time The Parent Unit can t be operated on the charging cradle without batteries Rechargeable batteries in the Parent unit give up to 10 hours continuous usage Please note however that new batteries do not reach full capacity until they have been in normal use for several days Running rechargeable batteries right down at least once a week will help them last as long as possible The charge Capacity of rechargeable batteries will reduce with time as they age so reducing the performance time of the parent unit Eventually they will need to be replaced The red power lights do not turn on when you plug 1 Check if the units are properly connected to the power supply in the power 2 Check if the power is turned on If not Press to turn on the power The green Link light on the Parent Unit is flashing i ken fb cm A e a a AOUE Cisse To R E A and cannot hear the sounds from your baby s l OOT 2 You may need to re establish the Link between the two units Turn both units off by pressing and holding the d and then turn on again by pressing the d Can t hear your baby on the Parent Unit but the Link light is stil2. be heard from the units feedback Check if the Parent and Baby Units are too close together Move them further apart Operating Frequency DECT 1 8 GHz Up to 300m under optimum conditions The range is Range reduced in buildings up to 50m as a result of walls doors etc Input 240 Vac 50Hz Output 6 Vpc 200 mA Non rechargeable batteries babv unit Type AA 1 5 V Alkaline not included in the package contents Input 240 Vic 50Hz Output 6 Vpc 200 mA Rechargeable batteries parent unit 9 p Type AAA 1 2 V 800 mAh NiMH included in the package contents Operating time with charged battery Approx 10 hours Power supply baby unit Power supply parent unit Warranty Information Australia Oricom makes no other warranties or conditions express or implied including as to merchantability and fitness for a particular purpose except as stated in this Warranty Any implied warranties that may be imposed by law are limited in duration to the Warranty Period Oricom warrants that the product is free from defects in materials or workmanship during the Warranty Period This Warranty in no way affects your statutory warranty rights under the Trade Practices Act 1974 or any other similar legislation This Warranty does not extend to any product from which the serial number has been removed was purchased outside of Australia or that has been damaged or rendered defective 1 asa result of lightning over
3. more audio is picked up the more lights will be lit When no audio is picked up all 8 lights will be off e If the volume of the Parent Unit is turned off an alert will sound when the audio reaches the second red led Note Do not position the baby unit and the parent unit close to each other as feedback may be generated Adjusting Volume You can adjust the volume at which you hear your baby There are 5 volume levels and an Off setting on the Parent Unit Press L A to increase the volume and to decrease the volume When adjusting the volume the 5 green sound sensor lights will illuminate to indicate the volume level Paging If the Parent Unit is misplaced you can use X button on the Baby Unit to locate the Parent Unit e Press and hold X on the Baby Unit The Parent Unit will automatically reset to mid volume and the paging alert will sound e To stop the Page alert press any button on the Parent Unit or press l 2 l again on the Baby Unit Note If no button is pressed the paging tone will stop after 30 seconds If the Parent Unit volume is off the Parent Unit volume will reset to mid volume Night light The Baby Unit has a one touch night light which emits a soft starry glow providing comfort and reassurance for your baby and allowing you to see them in a darkened room Press Jon the top of the baby unit A soft light will turn on gently Press again and the light
4. or skin It can be toxic and fatal if swallowed If there is any sign of poisoning immediately call emergency 000 When your Baby Monitor is not in use it is recom mended that you disconnect it from the mains supply and remove the batteries Observe the proper polarity or direction of any battery Reverse insertion of the battery cell can result in leakage or explosion and in turn harm or even death e The Ni MH batteries supplied with this product may be able to be recycled once they are unable to recharge during normal operation Always observe your local Council State regulations regarding the disposal of your packaging materials exhausted batteries and old equipment e Always recycle where possible Do not use your baby monitor in an explosive hazard area such as where there is gas leaking e As there is a slight chance that the product could be damaged by an electrical storm it is recommended that users unplug from the mains supply during an electrical storm Cleaning and care The surface of the case can be cleaned with a dry soft lint free cloth Never use cleaning agents particularly aggressive solvents Apart from occasional cleaning of the case no other care is necessary Thank you for choosing this monitor from Oricom Your Secure 50 Baby Monitor offers the best Digital Technology INTERFERENCE Gai FREE FREQUENCY Nae DECT Digital Enhanced Cordless Telecommunications is the most widely use
5. will fade away Out of Range When the baby and parent units have no link with each other eg Out of range parent unit or Baby unit is not powered on the green Link light flashes The link break alert will be heard from the Parent Unit once only When the units are linked the green Link light will be steadily lit Low Battery Baby Unit When the battery power is low the power light will flash Parent Unit When the batteries are low the red power light will flash And also the battery low warning beep will be heard The unit still can be used for 30 minutes You should put the parent unit on the charger pod to recharge the batteries Note Low battery alert can be suppressed by pressing any button Charging the Battery The Parent Unit will work for up to 10 hours with fully charged batteries If a battery low warning beep is heard and the red Power light on the Parent Unit is flashing you should put the parent unit on the Charger Pod to recharge the batteries You can still use your Parent Unit from the Charger Pod When charging the red power light on the charger will light steadily When you switch on your Parent Unit the green and red sensor lights will briefly indicate the current charge level of the batteries in the following way fully charged 6 lights illuminated a half charged battery is running 4 lights illuminated low 2 lights illuminated f o batteries need
6. Q icolli Babv Monitor Secure 50 WP ADVANCED N DECT 185 IN TECHNOLOGY _ A User Guide WARNINGS AND SAFETY INFORMATION GETTING STARTED YOUR BABY MONITOR BASIC OPERATION TROUBLESHOOTING PRODUCT SPECIFICATIONS GUARANTEE 11 12 13 AND oA Oe 1 IMPORTANT Please read this user guide thoroughly before use Your ORICOM Baby Monitor is designed to be an aid and should not be used as a substitute for responsible and proper adult supervision of a child The Baby Monitor has been designed to provide some added reassurance in the form of sound transmission for those times when you are not in the same room as your baby provided you always stay within hearing range of the baby monitor during use Your Baby Monitor is not a medical device nor a device to prevent cases of Sudden Infant Death Syndrome SID S or cot death and you should not rely on it for your baby s wellbeing It is important that you regularly check on your baby personally Make sure the Baby unit Parent unit and mains adaptor cables are kept out of reach of your baby and other young children within the house at all times at least one metre away from the baby s cot Never place the baby unit inside your baby s cot bed or playpen Never cover the Parent or baby units with clothes towels or blankets or any other item Do not place the cord in a high wear and tear location Never use a frayed
7. aced in the Charger Pod the 12 Battery Noise Level Indicators red charger light comes ON to indicate the batteries are charging Light will remain ON to ensure optimum charge Is maintained Indicates the battery level or Noise level 13 Link Light Green light ON indicates Linked to Baby Unit Flashing light indicates Link is lost 8 Once you have set up your Baby Monitor you will be able to hear the sounds in your baby s room through the Parent Unit And also see the green and red sensor lights around the top of the Parent Unit rise and fall with the sound levels Note If the connection between the Parent and Baby Units is broken at any time the green Link light on the Parent Unit will flash slowly the parent unit will beep to alter you that the link has been lost and the green and red sensor lights will cease to react to any sounds Move closer to the baby unit or follow the directions in Troubleshooting chapter to re establish the link Power On Off Once connected to the power supply e Press amp on each Unit to turn on the power e To switch off press and hold the amp Monitoring e Position the baby unit accordingly It should be placed 1 metre to 1 5 metres away from the baby s cot on a flat surface e Take the parent unit to monitor e Audio picked up by the baby unit microphone is depicted on the 8 lights on the parent unit 5 green and 3 red The
8. actices Act 1974 applies to this Warranty and which may not be so excluded restricted or modified For warranties that cannot be excluded restricted or modified Oricom limits the remedies available to those specified in the relevant legislation Customer Support If you Suspect your product is not functioning to specification before making a warranty claim please use the following resources Troubleshooting Guide in this user guide Online Frequently Asked Questions www oricom com au Email our customer support team on support oricom com au Contact Oricom Customer Support team on 1300 889 785 or 02 4574 8888 Monday to Friday 9am to 50m EST Please retain your purchase receipt and attach to the back page of this user guide Visit www oricom com au to register your product online Australia Customer Support Oricom International Pty Ltd Email support oricom com au Locked Bag 658 Web www oricom com au South Windsor NSW 2756 Phone 1300 889 785 Fax 02 4574 8898 Qricom
9. be located in separate rooms To prevent feedback do not take the parent unit into the nursery baby s room Baby unit Sender i Night light Kev Press to turn On the night light Press again to turn off the Light Power On Off Kev Press to turn the Unit ON Press and hold to turn the Unit OFF Page Kev Press and hold this kev Parent unit makes an audible alert Useful to call for assistance or to locate a missing Parent Unit Power light Red light glows when the power is On A slow flashing light indicates batteries are low Microphone Picks up the sounds from your baby s room Left view of baby unit 6 DC 6V input Connecting to Power Adapior Parent unit Receiver 7 Battery Cover Rechargeable batteries 8 Belt Clip 9 Volume Up Down Keys Adjust the Volume at which you hear the sounds in your baby s room 10 Power Key Press and release to turn it ON Press and hold to turn it OFF VLOEKE 7 11 Power Light Charger Pod Red light when the power is ON Flashing light indicates rechargeable batteries need 14 Charging Light recharging When Parent unit is pl
10. d worldwide digital cordless technology offering amazingly clear sound long range and maximum voice security DECT operates on the 1 8Ghz frequency which eliminates potential interference from other common wireless devices such as cordless telephones wireless networks Wi Fi Bluetooth and cordless computer devices Pack Contents e Parent unit receiver e Baby unit Sender e Mains adaptor with charger pod e 2x NiMH rechargeable batteries type AAA 800mAh e Mains adaptor with power cord N Installation For the Parent Unit 1 Remove the Belt Clip by lifting the clip at the top and sliding it downwards Then remove the battery cover on the back of the Parent Unit by switching the OPEN switch Insert the rechargeable batteries Supplied as marked on the unit and close the cover again Place the Parent Unit into the Charger Pod Plug the mains adaptor into a mains power socket clip battery cover The red charger light on the charger pod will illuminate indicating that the Parent Unit is charging the light will remain on to ensure optimum charge is maintained WARNING DO NOT USE STANDARD ALKALINE BATTERIES IN THE PARENT UNIT AS THERE IS A RISK OF EXPLOSION AND OR INJURY USE ONLY Ni MH RECHARGEABLE BATTERIES AS SUPPLIED 4 5 Press to turn the Parent Unit on e Before first use or if it has bee
11. ecurring failure Oricom at its discretion may elect to provide you with a replacement product of its choosing that is at least equivalent to your product in performance Oricom does not warrant that the operation of the product will be uninterrupted or error free Oricom is not responsible for damage that occurs as a result of your failure to follow the instructions that came with the product These terms and conditions together with any specific terms and conditions contained in the user guide to the product purchased constitute the complete and exclusive agreement between you and Oricom regarding the product No change to the conditions of this Warranty is valid unless it is made in writing and signed by an authorised representative of Oricom Oricom is not liable for any damages caused by the product or the failure of the product to perform including any lost profits or savings or special incidental or consequential damages Oricom is not liable for any claim made by a third party or made by you on behalf of a third party This limitation of liability applies whether damages are sought or a claim made under this Warranty or as a tort claim including negligence and strict product liability a contract claim or any other claim However this limitation of liability will not apply to claims for personal injury Nothing in this Warranty excludes restricts or modifies any condition warranty right or remedy which pursuant to the Trade Pr
12. l glowing steadily Check if the volume is turned up on the Parent Unit ee four re chargeable batteries are running low Return the Parent Unit to the The Red Power light is flashing on the Parent Unit Charger Pod to recharge them 1 The batteries in the parent unit are not fully charged Charge the parent unit for 14 hours before use 2 The power to the baby unit may be turned off or disconnected and or the Baby unit may be turned off Reconnect the AC power adaptor to the baby unit and or turn on the baby unit You may have to re establish the link between the two units You will need to remove the batteries from the parent unit and register the parent unit back to the baby unit by following the instructions below A Ensure batteries are removed from the Parent unit and baby unit if fitted and the IMO DA E PAGA AC power plug is disconnected from the Baby unit Press and hold the cd on the BABY unit then plug in the AC power plug after 2 seconds when the baby unit night lights flash release the d button Press and hold the d on the PARENT unit then insert the batteries after 2 seconds the parent unit will sound an alert and the level indication red LED s will flash then release the 5 button C After a few seconds the PARENT unit will give a confirmation tone and the units will be re linked and ready to use NOTE Steps A and B need to be performed within 50 secs A high pitched ear piercing noise will
13. n out of use for a long time the Parent Unit will need to be charged for 15 16 hours During this time the Parent Unit will operate from the Charger pod when switched on Note that the Parent Unit cannot be used without batteries even if it is placed in the charger 4 Press to turn on the Baby Unit e The Baby Unit should be placed about 1 metre to 1 5 metres away from the baby s cot on a flat surface Never place the Baby Unit inside the cot bed or playpen Make sure the unit cords and mains adaptor are out of reach of the baby and other young children Never place either Unit on antique or polished surfaces as slippage or scuffing may For the Baby Unit occur The unit may cause harm if it falls onto baby 1 In the event of a power failure your Baby Monitor can or other young children switch to battery power It is therefore recommended that Note you insert non rechargeable batteries in the Baby Unit 2 Remove the battery cover on the back of the Baby Unit by switching the OPEN switch Insert 3 alkaline batteries of the type AA not provided as marked on the unit and close the cover again Do not use rechargeable batteries in the Baby Unit 3 Plug the power cord into the power input at the side of the Baby Unit and plug the adaptor plug into a mains power socket If you place the Parent and Baby units too close together you will hear a high pitched noise called feedback this is normal The units are designed to
14. or compromised cord Never use or place your Parent or Baby units in or near moisture or water e g near bath or pool Immersing in water can cause electric shock and even death Power requirements In Australia this product requires an electrical supply of 220 240 volts single phase alternating current CAUTION Use only the mains power adaptors supplied with this equipment Incorrect adaptor polarity or voltage can seriously damage the unit and or cause physical harm and even death The adaptors may become warm during use please take care when handling AC Adaptor Baby unit Input 240V4c 50Hz Output 6Vrc 200mA AC Adaptor Parent unit Input 240V4c 50Hz Output 6Vpc 200mA If you plan to use your Baby monitor whilst travelling overseas make sure that the voltage shown on the mains power adaptor is the same as the local mains power before connecting to the power supply Do not use any voltage converter with the monitor 2 BURNIN AND SA NEORMATION Battery requirements Each parent unit requires two rechargeable Ni MH batteries size AAA 1 2V 800mAh HR10 44 Do not dispose of the batteries in a fire as they can explode Do not open unscrew or temper with any of your baby monitor units or battery Always carry out repairs through your authorised ORICOM representative or other duly qualified tradesperson Released electrolyte from the battery is corrosive and can cause damage to the eyes
15. voltage accident misuse abuse or other external causes 2 the operation outside the normal use of the product by the use of parts not manufactured or sold by Oricom or 4 by modification or service by anyone other than a Oricom or b an Oricom authorised service provider The Warranty Period will be 36 months from the date of purchase of the product evidenced by your dated sales receipt You are required to provide proof of purchase as a condition of receiving warranty services You are entitled to a replacement or repair according to the terms and conditions of this document if your product is found to be faulty within the Warranty Period This Warranty extends to the original purchaser only and is not transferable Batteries if supplied with this product are covered under this warranty for a period of 90 days Oricom products are manufactured using new materials or new and used materials equivalent to new in performance and reliability Spare parts may be new or equivalent to new Spare parts are warranted to be free from defects in material or workmanship for thirty 80 days or for the remainder of the Warranty Period of the Oricom branded product in which they are installed whichever is longer During the Warranty Period Oricom will replace and where possible repair the defective product All component parts removed under this Warranty become the property of Oricom In the unlikely event that your Oricom product has a r
Download Pdf Manuals
Related Search