Nissan 2006 Altima Automobile User Manual
Contents
1. food ers CAMEL You can also set the display to remind you that maintenance needs to be performed CLOCK SET ADJUSTMENT Press the SETTING button select the Clock key and press the ENTER button to access the following clock settings On screen clock When this item is turned to ON a clock is always displayed in the upper right corner of the screen The clock is automatically adjusted by the GPS system Clock format Choose either the 12 hour clock display or the 24 hour clock display Offset adjust Adjust the time by increasing or decreasing per minute E Daylight Savings Time Turn this item to ON for daylight savings time application Time Zone Choose the time zone Refer to your Owner s Manual and Navigation System Owner s Manual for additional information on your navigation system SCREW IN RECOVERY HOOK Your vehicle is supplied with a screw in recovery hook for pulling the vehicle forward For example Pulling the vehicle onto a flat bed for towing The screw in recovery hook tool is located in the right rear luggage compartment area under the cover along with the vehicle jack To install the recovery hook Remove the recovery hook cover from the front bumper Install the recovery hook as shown in the photo Turn it clockwise until securely tightened AUTOMATIC TRANSMISSION Manual Shift Mode E When the shift selector lev2. AGINS MOINO JOSE 4006 INSTRUMENT BRIGHTNESS CONTROL TRIP COMPUTER MODE SETTING BUTTONS See your Owner s Manual fpr more information HEADLIGHT AND TURN SIGNAL CONTROL STEERING WHEEL SWITCH FOR AUDIO CONTROL CRUISE CONTROL WINDSHIELD WIPER WASHER SWITCH SOFT TOP OPERATING SWITCH Roadster Models TCS VDC OFF SWITCH FUEL FILLER DOOR RELEASE HOOD RELEASE STEERING WHEEL TILT ADJUSTMENT CONTROL PANEL DISPLAY AUDIO SYSTEM CLIMATE CONTROLS _ _ HEADLIGHT AND TURN SIGNAL CONTROL HEADLIGHT SWITCH Turn the headlight switch to the DdE position to turn on the front parking side marker tail license plate and instrument panel lights Turn the headlight switch to the ZO position to turn on the headlights All other lights remain on HIGH BEAM Push the headlight switch forward to select the high beam function The blue O indicator light illuminates Pull the headlight switch back to the original position to select the low beam The blue ZO indicator light goes off Pull and release the headlight switch to flash the headlight high beams and off TURN SIGNAL SWITCH Move the headlight control switch up or down to signal the turning direction When the turn is completed the turn signals cancel automatically To signal a lane change move the headlight control switch up or down to the point where the indicator light begins to flash but
3. approximately 60 seconds when the key 15 turned on After 60 seconds the light will remain on Have the system checked by a NISSAN dealer CRUISE CONTROL if so equipped STEERING WHEEL SWITCHES FOR AUDIO CONTROL if so equipped To activate the cruise control push the ON OFF switch The indicator light in the instrument panel will illuminate To set cruising speed accelerate the vehicle to the desired speed push the COAST SET switch and release it The SET indicator light in the instrument panel will illuminate To reset at a faster cruising speed push and hold the ACCEL RES switch When the vehicle reaches the speed you desire release the switch To reset at a slower cruising speed push and hold the COAST SET switch Release the switch when the vehicle slows to the desired speed To resume a preset speed push and release the ACCEL RES switch The vehicle returns to the last set cruising when the vehicle speed is over 25 MPH 40 km h To cancel cruise control push the CANCEL switch or tap the brake pedal The SET indicator light in the instrument panel will go out To turn off cruise control push the ON OFF switch Both the CRUISE indicator light and the SET indicator light in the instrument panel will go out With the ignition switch turned to the ACC or ON position push the PWR Power on off switch to turn the audio system on or off Push the MODE select switch to change the mode e Without satel
4. assenger Refer to the Owner s Manual for detailed information regarding seat belt usage FRONT SEAT ADJUSTMENTS WITH MANUAL SEATS WITH POWER SEATS if so equipped Pull up on the lever under the front of the seat and slide backward or forward to the desired position Release the lever to lock the seat in position Lift the lever on the side of the seat to adjust your seatback backward or forward release the lever when you have found a comfortable angle and the seat belt fits properly Turn either dial to adjust the angle and height of the seat cushion to the desired position Move the sliding switch forward backward to adjust seat cushion to desired position Move the reclining switch LA forward or backward to adjust the seatback to the desired angle Turn either to adjust the angle and height of the seat cushion to the desired position REMOTE KEYLESS ENTRY SYSTEM LOCK DOORS Press the button to lock all doors UNLOCK DOORS Press the button once to unlock the driver s door only Press the button again within 5 seconds to unlock all doors RELEASING HATCH TRUNK LID Press and hold the trunk release button for longer than 0 5 seconds to open the trunk lid USING THE PANIC ALARM Press and hold the button for longer than 0 5 seconds The panic alarm will sound and the headlights will stay on for 25 seconds The panic alarm stops when it has run for 25 seconds o
5. er is shifted from D Drive to the manual shift gate the transmission enters the manual shift mode In the manual shift mode shift range 15 displayed on the position indicator in the meter When shifting up move the shift selector lever to the up side Shifts to higher range When shifting down move the shift selector lever to the down side Shifts to lower range In manual shift mode the transmission automatically shifts down to M1 first before the vehicle comes to stop When accelerating again it is necessary to shift to the desired range When canceling the manual shift mode return the shift selector lever to the D Drive position The transmission returns to the normal driving mode MANUAL TRANSMISSION Reverse Gear Lock out In 6 speed manual transmission equipped vehicles the shift lever is equipped with a reverse lock out feature that prevents accidental selection of R Reverse instead of 6th gear Shifting to Reverse Depress the shift lever down then move it to the right and back into R reverse NOTE When shifting always depress the clutch pedal fully to avoid noise and gear grind MIRROR ADJUSTMENT The rear view mirror has two pivot points for adjustments Adjust the rear view mirror height at the rear pivot and tilt the mirror at the front pivot Position the mirror to provide the best visibility through the rear window bees SS SS SOFT TOP OPERATION Before openin
6. g or closing your soft top refer to the Owner s Manual for detailed Warnings and Cautions regarding soft top operation Open the top 1 Make sure the area is clear of obstructions and that there is at least 6 feet of clearance above the vehicle 2 Apply the parking brake and make sure the transmission is in the P Park position automatic transmission or the N Neutral position manual transmission 3 Step on the brake pedal 4 Start the engine 5 Push the safety switch black located in the center of the top latch lever Push the top latch lever silver forward to unlatch the top 6 Press and hold the OPEN side of the soft top operating switch until the top is fully open and stowed and the indicator light turns off Close the top 1 Make sure the area is clear of obstructions and that there is at least 6 feet of clearance above the vehicle 2 Apply the parking brake and make sure the transmission is in the P Park position automatic transmission or the N Neutral position manual transmission 3 Step on the brake pedal 4 Start the engine 5 Press and hold the CLOSE side of the soft top operating switch until the top is fully closed and the indicator light begins to flash 6 Securely latch the top with the top latch lever The indicator light turns off If the top does not close when using the operating switch refer to the Owner s Manual for the procedure to manually close
7. lash Press the SEEK TRACK button to adjust the hour Press the TUNE button to adjust the minutes To change the play pattern of the CD press the RPT button STATION AND CD SELECT BUTTONS To store a radio station preset you must first tune to the desired station Then press and hold the desired station select button until a beep is heard The channel indicator will come on indicating memorization is complete AUDIO BUTTON Adjust the BASS TREBLE FADE BALANCE and AUDIO PILOT by pressing the AUDIO button until the desired mode appears in the display SAT presets are only available on SAT equipped vehicles AUTOMATIC CLIMATE CONTROL AUTO MODE Turn both the fan speed control dial and the air flow control dial to the AUTO positions Then turn the temperature control to the desired temperature This will allow the fan speed air flow distribution and temperature to be automatically maintained TEMPERATURE CONTROL DIAL Turn the temperature control dial left for cold air or right for hot air AIR FLOW CONTROL DIAL Turn the dial to select the following air flow outlets A Air flows from the center and side vents Air flows from the center side and foot vents 2 Air flows mainly from the foot vents 01 Air flows from the defroster and foot vents 947 Air flows mainly from the defroster vents AUTO air flow distribution of the passenger compartment will be maintained auto
8. lite radio AM FM1 FM2 and CD or CD changer e With satellite radio AM FM1 FM2 SAT1 SAT2 and CD changer The SEEK switch can be used to perform the following e Radio memory change Push the switch for less than 1 5 seconds to change the radio frequency e Radio tuning Push and hold the 4 switch for more than 1 5 seconds to seek the next or previous radio station e CD track change Push the 4 switch for less than 1 5 seconds to return to the beginning of a CD track or skip to the next track e disc change Push and hold the switch for more than 1 5 seconds to change the playing disc e folder change Push and hold the 4 switch up or down for more than 1 5 seconds to change the folders if folders exist wi R Uan e ois 1043 FM AM SAT RADIO WITH CD CHANGER if so equipped LOAD BUTTON LOAD A SINGLE DISC Press the LOAD button for less than 1 5 seconds Select the loading slot by pressing the CD insert select button 1 6 then insert the CD LOAD UP TO 6 DISCS Press and hold the LOAD button for more than 1 5 seconds The slot numbers 1 6 will illuminate on the display when CDs are loaded into the changer RADIO BAND SELECT Press the RADIO band select button to change the band as follows Without satellite radio gt 1 gt 2 gt With satellite radio gt 1 gt 2 gt SAT1 2 gt SCAN BUTTON To scan quickly thr
9. matically when the control dial is turned to the AUTO position FAN SPEED CONTROL DIAL Turn the fan speed control dial to the left slower or right faster to manually control fan speed Turn the dial to the AUTO position to automatically control fan speed DEFROSTING DEFOGGING FRONT AND SIDE WINDOWS Turn the air flow control dial to the front window defroster mode W The A C automatically turns on when the defroster mode is selected Turn the temperature control dial left or right to set the desired temperature set the defroster on high turn the fan speed dial all the way to the right DEFROSTING DEFOGGING REAR WINDOW AND OUTSIDE HEATED MIRROR Push the rear window defroster switch W on Push the switch again to manually turn the defroster off This function automatically turns off in approximately 15 minutes A C ON OFF BUTTON Press the A C button to manually turn the A C on or off AIR RECIRCULATION FRESH AIR BUTTON Press the air intake button to alternate between air recirculation and CS fresh air The air recirculation mode cannot be selected if the air flow control dial is in the defrost position W NOTE When the center button is pressed to recirculate the interior air the A C will automatically turn on if not already on This is done to help reduce window fogging TRACTION CONTROL SYSTEM TCS OFF SWITCH if so equipped The vehicle should be driven with the Tractio
10. n Control System TCS on for most driving conditions TCS reduces the engine output to reduce wheel spin The engine speed will be reduced even if the accelerator is depressed to the floor If maximum engine power is needed to free a stuck vehicle such as from mud or snow turn the TCS off To turn off the TCS push the TCS OFF switch The indicator light will illuminate Push the switch again or restart the engine and the system will operate normally FRONT PASSENGER AIR BAG STATUS LIGHT This vehicle is equipped with the Nissan Advanced Air Bag system Under some conditions depending on the type of occupant or object detected in the front passenger seat by the occupant classification sensor the front passenger air bag 15 designed to automatically turn OFF When the front passenger air bag is OFF the front passenger air bag status light will illuminate For example When the system detects that the front passenger s seat is occupied a small adult child or child restraint as outlined in the Owner s Manual the will illuminate to indicate that the front passenger air bag is OFF and will not inflate in a crash When front passenger s seat is occupied and the passenger meets the conditions outlined in the Owner s Manual the will not illuminate to indicate that the front passenger air bag is operational When the system detects that the front passenger s seat is unoccupied passe
11. nger air bag status light will not illuminate even though the front passenger air bag is OFF Refer to the Owner s Manual for detailed information regarding the Nissan Advanced Air Bag System SEATBACK TILT CANCEL SWITCH Roadster only The passenger seat of the 350Z Roadster automatically tilts forward when operating the soft top This function can be cancelled by pushing the seatback tilt cancel switch to the CANCEL position Push the seatback tilt cancel switch to the AUTO position to reactivate the power seatback tilt switch lf the seatback tilt cancel switch is in the CANCEL position the seatback tilt paddle switch located on the back of the passenger seat will not work In this situation tilt the passenger seatback forward using the power seat position switch SEAT BELT WARNING LIGHT AND CHIME The light and chime remind you to fasten your seat belts The f light illuminates whenever the ignition key is turned to the ON or START position and remains illuminated until the driver s seat belt is fastened At the same time the chime sounds for about 6 seconds unless the driver s seat belt is securely fastened The seat belt warning light may also illuminate if the front passenger s seat belt is not fastened when the front passenger s seat is occupied if so equipped For 5 seconds after the ignition switch is in the ON position the system does not activate the warning light for the front p
12. ough each broadcasting station press the SCAN button The tuner will pause for 5 seconds on each broadcasting station When the SCAN tuning button is pushed while a CD is being played the beginning of all the tracks of the CD will be played for 10 seconds in sequence PTY Program BUTTON Use the PTY Program button to search for certain program types such as ROCK COUNTRY JAZZ CLASSICAL etc SEEK TRACK BUTTON To find the next broadcasting station press the SEEK TRACK button To skip from one track to another on a CD press the SEEK TRACK button Each time the button is pressed the CD will advance or skip back one track DISP Display BUTTON Pressing the DISP button will display additional information for example Title Artist name PLAYBACK if so equipped In addition to playing audio CDs this audio system can play MP3 files recorded on CD ROM CD R and CD RW discs Each disc can have a maximum of 8 folder levels and 255 folders A total of up to 512 MP3 files can be played back During MPS playback some recorded ID3 tag information can be displayed by pressing the DISP button TUNE REW FF BUTTON To fast forward or rewind a CD track press the REW FF button The CD will play at an altered speed until the button is released To manually tune the radio press the TUNE button RPT BUTTON To adjust the digital clock display press and hold the RPT button for more than 1 5 seconds until the clock display starts to f
13. r when any button is pressed on the keyfob POWER WINDOWS The power windows operate when the ignition key is in the ON position and for about 45 seconds after the ignition key is turned to the OFF position Automatic Adjusting Function The front door power windows have an automatic adjusting function This ensures the windows close completely to help seal against wind noise and weather leaks When the front doors are being opened the windows automatically lower slightly to avoid contact between the Per windows and the side roof panels When the doors are closed the windows automatically raise 2 slightly SECONDARY REAR HATCH RELEASE Your vehicle is equipped with a secondary rear hatch release mechanism This allows opening of the rear hatch in the event of a discharged battery or in an emergency The secondary rear hatch release is located under the strut tower bar Coupe or inside the storage bin compartment Roadster upper right side open the rear hatch from the inside firmly pull the release handle to the left towards the passenger side until the lock releases CONTROL PANEL DISPLAY WITH NAVIGATION SYSTEM if so equipped INFO BUTTON z When the INFO button is pressed the ae fi Maintenance screen will be displayed To set the maintenance interval for the Engine Oil or Oil Filter choose an item Peers m using the joystick and press the ENTER ina a aaa button
14. reset adjust the various mode selections RPM SHIFT INDICATOR Manual transmission only The engine RPM shift indicator light REV is located in the tachometer During driving it indicates shift point or time to up shift KATTIS 5 x1000n min The shift indicator light will begin flashing about 500 RPM before a pre set engine RPM is reached in any gear Then when the actual pre set RPM is reached the shift indicator light will stop flashing and remain on The engine RPM shift point may be set by the driver using the Trip Computer display Or it may be deactivated also using the Trip Computer display TIRE PRESSURE MONITORING SYSTEM TPMS This system monitors tire pressure Please remember this system does not detect a sudden drop in tire pressure for example a blowout while driving It also does not monitor the air pressure in 1 the spare tire Tire pressure 15 affected by temperature Low outside temperature causes lower tire pressure This may cause the low tire pressure warning light to illuminate If the low tire pressure warning light illuminates check the tire pressure in all four tires To turn the low tire pressure warning light off adjust the low tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label located in the door opening If TPMS is not functioning properly the low tire pressure warning light will flash for
15. the headlight control switch does not latch WINDSHIELD WIPER WASHER SWITCH The ignition switch must be in the ON position to activate the windshield wipers 2 Move lever to the following positions to 05 operate the windshield wipers Intermittent INT Front wipers operate intermittently and can be further adjusted by twisting the time control ring operation of front wipers Q api Low Speed LO Continuous low speed 02 4 High Speed HI Continuous high speed operation of front wipers Mist MIST Lift the lever up for one sweep of the front wipers Rear Wipers REAR Twist the end section to operate the first INT or second ON speed settings for the rear wipers The washer function activates the washer fluid and several sweeps of the wipers e For FRONT WASHER pull lever toward you e For REAR WASHER push lever away from you Coupe only TRIP COMPUTER The trip computer may be used to check items such as speed outside air temperature distance to empty fuel average mileage and speed elapsed time and distance traveled Additionally it can function as a stopwatch or be used to operate the RPM shift feature REV Manual transmission only To operate the Trip Computer Turn the ignition switch on Then press the side of the buttons Press the button 01 toward left to scroll through each mode E Press the button 02 toward left to
16. the top REAR FLOOR BOX Rear floor storage is located behind the passenger s seat Fold the passenger s seatback forward to access the rear floor box e Coupe Pull up on the lever e Roadster Push the upper portion of the passenger power seat switch Pull up on the lever J to open the rear floor box NOTE The rear floor storage box has additional space under the bottom plate Using the master key lock the storage box turn key to the right or unlock the storage box turn key to the left Return the passenger s seatback to a locked position after using the rear floor box e Coupe Pull up on the lever to return seatback to Original position e Roadster Push lower portion of the passenger power seat switch FZ to return seatback to original position This easy to use Quick Reference Guide is intended to help you more fully appreciate some of the unique features and functions of your new vehicle However it is not intended to replace your Owner s Manual The Owner s Manual contains more detailed information to help you better understand the important safety warnings features operation and maintenance of your vehicle Nissan the Nissan Brand Symbol SHIFT_ tagline Z and Nissan model names are Nissan trademarks 2006 Nissan North America Inc QR7E 0Z33U0 Printing November 2006 12
Download Pdf Manuals
Related Search