Navman FUEL 2100 Automobile Parts User Manual
Contents
1. Hold down during power up 5 Release the 3 key Display will flash current total log value NI ly 7 I 6 Use the 3 or amp keys to make the display indicate the actual volume of fuel used 7 Press both keys simultaneously for 1 sec to exit Press and hold for 1 second The fuel flow meter is now calibrated NAVMAN FUEL 2100 Installation and Operation Manual 3 Installation WARNING ITIS VERY IMPORTANT TO INSTALLA FUEL FILTER BETWEEN THE FUEL FLOW TRANSDUCER AND THE FUEL TANK THIS FILTER WILL CATCH LARGER PARTICLES OF DIRT FROM THE FUEL TANK AND PREVENT THE FINE GAUZE FILTER IN THE FUEL FLOW TRANSDUCER FROM BECOMING BLOCKED AS THIS MAY DAMAGE THE ENGINE Location Mounting The FUEL 2100 is designed for above or below deck The instrument panel must be 3mm to 19mm installation Select a position that is 1 to 3 4 in thickness Ona flat surface BDrilla 51mm 2 hole in the instrument panel Atleast 300mm 12 from a compass Remove brackets and insert the instrument so Atleast 500mm 20 from any radio the back is flush with the instrument panel Easy to read by the helmsman and crew Slide the bracket over the instrument and Protected from physical damage tighten the mounting nut until secure Accessible to electrical cable connections NAVMAN Instrument 51mm 2 Hole Mounting Bracket Instrument bog S Sealing Gasket FUEL 2100 Instal2. 1 Operati m 4 Fuel Flow 4 Other Fuel Functions Changing the fuel remaining value Setting the low fuel alarm Alarm activation Resetting the TRIP LOG or the TOTALLOG Puis Selecting units of measure Calibration SINStANAION E r E E Location Mounting Wiring Connection Installation of the fuel flow transducer Appendix A Specifications l u u uu Appendix B Troubleshooting Chart 10 Appendix C How to contact US u u 59 Important It is the owner s sole responsibility to install and use the instrument and transducer s in a manner that will not cause accidents personal injury or property damage The user of this product is solely responsible for observing safe boating practices NAVMAN NZ LIMITED DISCLAIMS ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN AWAY THAT MAY CAUSE ACCIDENTS DAMAGE OR THAT MAY VIOLATE THE LAW This manual represents the FUEL 2100 as at the time of printing Navman NZ Limited reserves the right to make changes to specifications without notice Governing Language This statement any instruction manuals user guides and other information relating to the product Documentation may be translated to or has been translated from
3. a whistling noise will indicate the turbine is rotating Low flow reading indicated 1 Check that the gauze filter is clean If the filter is not installed fine strands may clog up the turbine 2 Check calibration is correct High or erratic reading Check fuel connections are well made Air in fuel lines will cause erratic or high readings 10 NAVMAN FUEL 2100 Installation and Operation Manual Appendix C How to contact us NORTH AMERICA NAVMAN USA INC 18 Pine St Ext Nashua NH 03060 Ph 1 603 577 9600 e mail sales navmanusa com OCEANIA New Zealand Absolute Marine Ltd Unit B 138 Harris Road East Tamaki Auckland Ph 649273 9273 e mail navman absolutemarine co nz Papua New Guinea Lohberger Engineering Lawes Road Konedobu PO Box 810 Port Moresby Ph 675 321 2122 e mail loheng online net pg Australia NAVMAN AUSTRALIA PTY Limited Unit 6 5 13 Parsons St Rozelle NSW 2039 Australia Ph 61 2 9818 8382 e mail sales navman com au SOUTH AMERICA Argentina Costanera UNO S A Av Presidente R Castillo y Calle 13 1425 Buenos Aires Argentina Ph 5411 4312 4545 e mail purchase costanerauno com ar Website www costanerauno ar Brazil REALMARINE Estrada do Joa 3862 CEP2611 020 Barra da Tijuca Rio de Janeiro Brasil Ph email vendas marinedepot com br 55 21 2483 9700 Equinautic Com Imp Exp de Equip Nauticos Ltda Av Diario de Not
4. another language Translation In the event of any conflict between any Translation of the Documentation the English language version of the Documentation will be the official version of the Documentation Copyright 2002 Navman NZ Limited New Zealand All rights reserved NAVMAN is a registered trademark of Navman NZ Limited NAVMAN FUEL 2100 Installation and Operation Manual 3 1 Operation Fuel Flow Press the key to display the current fuel flow Other Fuel Functions Press the key to cycle through the possible functions Each time the key is pressed the display will show an identifier for 2 seconds before the value is displayed Er Pl Fuel used on trip Fuel used in total Low luel alarm setting t Fuel remaining in tank Changing the fuel remaining value To change the value of fuel remaining in the tank press the key until the display indicates 15 for two seconds and then displays the current value J 6 bh a gt an aD rum Press and hold both keys for three seconds and the displayed value will begin to flash lt 3 Press and hold for 3 seconds Nl ly n S Use the 3 and keys to change the value Press and hold both keys for one second to save this new value to memory and to exit this function The display will indicate EAS and then the new value NAVMAN FUEL 2100 Installation and Ope
5. Depth behind face plate 95mm max Display 3 character LCD Colour Black with texture on bezel Backlighting Red coloured diffused lighting for display Water Integrity Front will withstand direct water spray Alarm Audio and visual alarm indicates remaining fuel total has dropped below a preset alarm value Flow 2 5 to 160 litres per hour 0 5 to 43 US gallons per hour 0 4 to 36 imperial gallons per hour Logs Logs record fuel used up to 999 display units Total Log is saved in memory at power down Both Trip Log and Total Log can be reset via the keypad Display is backlit for Night Operation Fuel Remaining User enters a fuel value into memory via the key pad The quantity of fuel used is automatically subtracted from this total This value remains in memory at power down Operating Voltage 8 V DC to 16 5 V DC Operating Temperature 0 to 50 32 to 122 F Current Drain 70 mA max RF Interference lt 6 dB quieting on any marine radio channel with 3 dB gain antenna within one metre of the instrument Complies with CE EMC standards EN50081 1 and EN50082 1 Change Value Up FUEL 2100 Installation and Operation Manual Change Value Down Appendix B Troubleshooting Chart No display 1 Check DC power connections and DC polarity with voltmeter 2 Check fuse No flow reading indicated 1 Check connection to flow transducer 2 Remove transducer from fuel line blow through transducer
6. FUEL 2100 English 3 Francais 11 Espanol 19 Deutsch 27 Nederlands 35 Svenska 43 Suomi 51 FUEL 2100 NAVMAN www navman com FCC Statement Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a normal installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an output on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced technician for help e Ashielded cable must be used when connecting a peripheral to the serial ports NAVMAN FUEL 2100 Installation and Operation Manual
7. ceeds 999 then both it and the trip log will be reset to zero 2 Instrument Setup Selecting units of measure The FUEL 2100 will indicate fuel values in Litres Imperial gallons or US gallons To change the current setting perform the following steps 1 Power up the unit while holding down the Hold down during power up 2 When the unit is on release the key The display will indicate the current display unit with Imperial Gallons US Gallons Litres 3 To select the display unit desired use the 3 and keys to change the value 4 To exit this mode press and hold both the 3 and keys simultaneously for one second 3 Press and hold to exit Information will now be indicated in the selected display unit Calibration The fuel transducer supplied with the fuel flow meter will provide readings at better than 5 accuracy Individual calibration will increase this level of accuracy to better than 2 over a fuel flow range of 10 0 to 120 litres per hour Use the following steps to calibrate your fuel flow meter 1 Resetthe total log value to zero see previous page 2 Use a known amount of fuel The larger the amount the more accurate the calibration will be 3 Take note of the actual volume of fuel used and the fuel used indicated by the total log If these two totals are different the instrument may require calibration 4 Press and hold the key while applying power
8. icias 1997 CEP 90810 080 Bairro Cristal Porto Alegre RS Brasil Ph 55 51 3242 9972 e mail equinautic equinautic com br ASIA China Peaceful Marine Electronics Co Ltd Hong Kong Guangzhou Shanghai Qindao Dalian E210 Huang Hua Gang Ke Mao Street 81 Xian Lie Zhong Road 510070 Guangzhou China Ph 86 20 3869 8784 e mail sales c peaceful marine com Website www peaceful marine com India Access India Overseas Pvt A 98 Sector 21 Noida India Ph 91 120 244 2697 e mail vkapil del3 vsnl net in Indonesia Polytech Nusantara Graha Paramita 2nd Floor Jln Denpasar Raya Blok D2 Kav 8 Kuningan Jakarta 12940 Tel 021252 3249 Korea Kumhomarine Technology Co Ltd 604 842 2F 1118 15 Janglim1 Dong Saha Gu Busan Korea Ph 82 51 293 8589 e mail info kumhomarine com Website www kumhomarine com Maldives Maizan Electronics Pte Ltd 8 Sosunmagu Male Ph 4 960 78 2444 e mail ahmed maizan com mv Singapore RIQ PTE Ltd 81 Defu Lane 10 Hah Building 02 00 Singapore 539217 Ph 65 6741 3723 e mail riq postone com Taiwan Seafirst International Corporation No 281 Hou An Road ien Chen Dist Kaohsiung Taiwan R O C Ph 886 7 831 2688 e mail seafirst seed net tw e Thailand Thong Electronics Thailand Company Ltd 923 588 Thaprong Road Mahachai Muang Samutsakhon 74000 Thailand Ph 66 34 411 919 e mail thonge cscoms com Vietnam Haidang C
9. ingdom PLASTIMO Mfg UK Ltd School Lane Chandlers Ford ndustrial Estate EASTLEIGH HANTS S053 ADG Ph 4423 8026 3311 e mail sales plastimo co uk Website www plastimo co uk Sweden Denmark or Finland PLASTIMO NORDIC AB Box 28 Lundenvagen 2 47321 HENAN Ph 46 304 360 60 mail info plastimo se ebsite www plastimo se o pain LASTIMO ESPA A S A venida Narc s Monturiol 17 8339 VILASSAR DE DALT Barcelona h 3493 750 75 04 e mail plastimo plastimo es Website www plastimo es lt G gt x Portugal PLASTIMO PORTUGAL Avenida de India N 40 300 299 Lisbon Ph 351 21 362 04 57 e mail plastimo siroco nautica pt Other countries in Europe PLASTIMO INTERNATIONAL 15 rue Ing nieur Verri re BP435 56325 Lorient Cedex France Ph 332 97 87 36 59 e mail lastimo international plastimo fr Website www plastimo com REST OF WORLD MANUFACTURERS Navman NZ Limited 13 17 Kawana St Northcote Box 68 155 Newton Auckland New Zealand Ph 649 481 0500 e mail marine sales navman com Website www navman com c sS 9 N z o o 2 N e N Q Q e NAVMAN Lat 36 48 404 S F C CE AGES vv
10. lation and Operation Manual 7 Wiring Connection Keep electrical and transducer cables away from alternator or other noise generating electrical cables Avoid connecting the instrument to power circuits that share loads with ignition alternators inverters and radio transmitters Electrical power supply connections should always be as short as possible BRACKET FUJI 5 PIN CONNECTOR Installation of the fuel flow transducer The fuel flow transducer is designed for installation in Coast Guard approved 9 5mm 3 flexible fuel line The transducer MUST be installed AFTER the main fuel filter It should be located well away from any area where it will be effected by excessive heat or vibration from the engine It is preferable to mount the transducer in a vertical position 8 Connect the red wire to the positive supply via 1 amp fuse or a 1 amp circuit breaker Connect the black wire to the electrical ground Connect the fuel flow transducer to the five pin transducer inlet cable BUZZER 600mm 24 POWER CORD N BLACK TERMINAL RED TERMINAL Drain all the fuel from the flexible fuel line Cut the fuel line and using the fuel hose fixing clips provided install the transducer so that the FUEL IN side of the transducer connects to the fuel tank NAVMAN FUEL 2100 Installation and Operation Manual Appendix A Specifications NAVMAN Size Mount 51mm diameter hole
11. o Ltd 6A ALE Ba thang hai St District 10 Hochiminh City Ph 848 8632159 e mail sales haidangvn com Website www haidangvn com MIDDLE EAST Lebanon and Syria Letro Balco Stores Moutran Street Tripoli VIA Beirut Ph 961 6 624512 e mail balco cyberia net lb United Arab Emirates Kuwait Oman Iran amp Saudi Arabia Abdullah Moh d Ibrahim Trading opp Creak Rd Baniyas Road Dubai Ph 971 4 229 1195 e mail mksq99 email com AFRICA South Africa Pertec Pty Ltd Coastal Division No 16 Paarden Eiland Rd Paarden Eiland 7405 Postal Address PO Box 527 Paarden Eiland 7420 Cape Town South Africa Ph 27 21 511 5055 e mail info kfa co za EUROPE France Belgium and Switzerland PLASTIMO INTERNATIONAL 5 rue Ing nieur Verri re BP435 56325 Lorient Cedex Ph 33 2 97 87 36 36 e mail plastimo plastimo fr Website www plastimo fr Germany PLASTIMO DEUTSCHLAND 5 rue Ing nieur Verri re BP435 56325 Lorient Cedex Ph 49 6105 92 10 09 49 6105 92 10 10 49 6105 92 10 12 e mail plastimo international plastimo fr Website www plastimo de Italy PLASTIMO ITALIA Nuova Rade spa Via del Pontasso 5 116015 CASELLA SCRIVIA GE Ph 39 1096 8011 e mail info nuovarade com Website www plastimo it Holland PLASTIMO HOLLAND BV ndustrieweg 4 6 2871 RP SCHOONHOVEN Ph 31 182 320 522 mail info plastimo nl Website www plastimo nl United K
12. ration Manual Setting the low fuel alarm Use the key to select the alarm function The LCD will indicate RL for two seconds and will then display the present alarm value If no alarm value has been entered the LCD will indicate GFF Press and hold both keys for three seconds and the displayed value will begin to flash 3 Press and hold for 3 seconds Nl ly ie N Use the and amp keys to select the desired alarm value Press and hold both keys for one second to save this new value to memory and to exit this function The display will indicate RL and then the new value Q The arrow pointing at the alarm bell will be activated NAVMAN FUEL 2100 Installation and Operation Manual Alarm activation If the fuel remaining value drops below the fuel alarm value the alarm will sound and the alarm arrow will flash Press any key to mute the alarm The alarm arrow will continue to flash as long as the alarm condition remains Resetting the TRIP LOG or the TOTAL LOG To reset a log press the key until the display indicates the name of the log to be reset Press and hold both keys for three seconds Display will show E P or k gk for 2 seconds before resetting to zero Press and hold for 3 seconds The trip log value may be reset without changing the total log value If the total log is reset to zero then the trip log will automatically reset to zero Note If the total log ex
Download Pdf Manuals
Related Search