Mustang Survival MD0450 22 Life Jacket User Manual
Contents
1. 9 Fold the cover panel down so that it covers the lobe Fig 32 Inflatable Vest with LIFT Owner s Manual 20 FIGURE 32 Velcro Tab 10 Mustang Survival uses advanced 2 step zippers SecurezIP Find the right zipper tail on the right lobe and ZIP 1 Reset the 2 step zipper by pulling the slider to the Velcro tab Figs 33 and 34 NOTE Fasten the Velcro tab to prevent the zipper from re opening ZIP 2 Close by pulling slider in the opposite direction to the end the zipper Fig 34 Ensure that the Inflatable cell does not get caught by the zipper when closing FIGURE 33 FIGURE 34 11 Find the left zipper tail on the right lobe and ZIP 1 Reset the 2 step zipper by pulling the slider to the Velcro tab Fig 35 21 MUSTANG SURVIVAL NOTE Fasten the Velcro tab to prevent the zipper from re opening ZIP 2 Close by pulling slider in the opposite direction to the end the zipper Fig 36 Ensure that the Inflatable cell does not get caught by the zipper when closing FIGURE 35 FIGURE 36 12 Tuck in the zipper tail so it is not exposed Fig 37 FIGURE 37 Zipper Tail 13 The right lobe should now be fastened closed and the inflator should be visible through the clear window Ensure the beaded handle is placed through the opening and is attached to the Velcro tab on the ou2. Instructions iv Perform the Oral Inflation Valve Test See the Oral Inflation Valve Test section 2 ii in the Care and Maintenance Instructions MUSTANG SURVIVAL v Ensure the current date is not past the date on the inflator If it is replace the inflator see Re arming Your PFD p 11 vi Ensure the single point status indicator is green Fig 2 Repack the Inflatable PFD as outlined in the Repacking section p 17 WARNING If you are not confident in the self inspection and servicing of your Inflatable Vest with LIFT in accordance with these instructions take your Inflatable Vest with LIFT to a Mustang dealer for professional servicing or contact Mustang Survival see contact information on back of manual Cleaning and Storing To avoid inflation do not submerge the Inflatable Vest with LIFT or directly spray the inflator Hand wash or sponge down the Inflatable PFD in warm soapy water Rinse the PFD and inflator with clean water using a clean rinse cloth Hang the Inflatable Vest with LIFT to dry ona plastic coat hanger Do not dry clean Always store your Inflatable Vest with LIFT in a warm dry place out of direct sunlight HOW AND WHY TO TEST YOUR PFD Inflate your Inflatable Vest with LIFT and try it out in the water to Make sure it floats you e Comfortably when worn properly e Adequately for expected wave conditions body shapes densities affect performance Make sure it wo
3. non emergency situation To orally inflate the PFD first locate the oral inflation tube by opening the wearer s right front panel cover of the PFD Then remove the dust cap from the end of the oral tube and blow into the tube until the PFD is fully inflated It may be neccessary to manually release the Velcro tabs located at the bottom of the left and right panel covers for full inflation because oral inflation may not provide sufficient pressure to open the tabs CAUTION CO inflation could over pressurize and damage your PFD if already orally inflated FIGURE 8 Inflatable Vest with LIFT Owner s Manual 8 In water Adjustments Follow these instructions to adjust the waist belt when wearing the Inflatable Vest with LIFT in the water To tighten a Grasp the loose end with the left hand Pull the webbing to your right side away from the buckle Fig 9 b Simultaneously grasp the waist belt along the body with the right hand approximately 6 inches to the right of the buckle and feed the webbing into the buckle FIGURE 9 To loosen a Simultaneously grasp and hold the waist belt with the left hand as you grasp the lobe on the right side with the right hand and pull away from the center Fig 10 FIGURE 10 9 MUSTANG SURVIVAL Special Considerations for Automatic Devices The PFD might not be armed when needed either knowingly or unknow ingly P
4. water just deep enough that you can stand with your head above the surface If you are a weak swimmer or non swimmer inflate the Inflatable Vest with LIFT partially so that you are supported well enough to Inflatable Vest with LIFT Owner s Manual 28 be able to complete inflation without touching bottom either orally or manually Note this level of inflation because it is the minimum needed for you to safely use this Inflatable Vest with LIFT 5 Fully inflate the Inflatable Vest with LIFT using the oral inflator It may be neccessary to manually release the Velcro tabs for full inflation because oral inflation may not provide sufficient pressure to open the tabs 6 See if the Inflatable Vest with LIFT will float you on your back or just slightly back of vertical In a relaxed floating position verify that your mouth is well above the water s surface Note the effect of where you hold your legs and how you float 7 Get out of the water and remove the Inflatable Vest with LIFT Completely deflate the Inflatable Vest with LIFT using the oral inflator see Deflation p 10 8 Let the Inflatable Vest with LIFT dry thoroughly Re arm p 11 and Repack the PFD p 17 Re assemble inflation system parts and repack the Inflatable Vest with LIFT WEAR YOUR PFD In approximately 80 percent of all boating fatalities the victims were not wearing a PFD Most fatal accidents happen on calm sunny days This in
5. G SURVIVAL 7 Now check the new manual automatic cap as follows Fig 18 1 Is the single point status indicator showing green 2 Is the expiry day OK If YES is the answer to both questions then proceed as follows If the answer is NO to either question get a new cap FIGURE 18 Single Point Indicator 8 Hold the CO cylinder through the fabric of the Inflatable Vest with LIFT Fig 19 Position the replacement cap with the water inlet valve pointing to the right and press firmly onto the inflator body and sealing ring Fig 20 FIGURE 19 FIGURE 20 Inflatable Vest with LIFT Owner s Manual 14 9 While pressing FIRMLY onto the inflator body turn the BLACK locking ring clockwise into the locked position Fig 21 Pull on the cap to make sure it has locked onto the inflator body FIGURE 21 10 Check To see that the single point status indicator on the cap is green the pull to inflate lanyard is present and that the locking ring is locked 11 Ensure the beaded handle is fed through the pocket opening and fastened to the Velcro tab Fig 39 12 Refold the Inflatable Vest with LIFT in accordance with the Repacking section p 17 Auto Manual Conversion Cap MA7219 Instructions These instructions apply only when the MA7219 is used with a MD0450 22 with an armed Hammar M1 inflator green status indicator CONVERSION
6. INSTRUCTIONS This will convert the MD3196 from an automatic inflation device to a manual inflation device The device may be changed back to an automatic inflation device by removing the conversion cap CAUTION A manual inflation device will not inflate on water contact unless the wearer activates the inflator 1 Completely unzip the right lobe zipper inflator side 15 MUSTANG SURVIVAL 2 Fasten by tying the conversion cap lanyard to the loop in the pocket immediately in front of the inflator after passing it through the opening in the cover Fig 22 FIGURE 22 Opening i UM Right Lobe Conversion Cap 3 Position the conversion cap over the inflator s hydrostatic valve opening The conversion cap s metal clip should be placed along the top of the inflator s hydrostatic valve Fig 23 FIGURE 23 4 Secure the conversion cap to the inflator s hydrostatic valve by applying pressure to the cap at the metal clip FIGURE 24 Inflatable Vest with LIFT Owner s Manual 16 CONVERSION CAP REMOVAL Once the conversion cap is removed the MD3196 becomes an automatic inflation device Firmly pull the conversion cap lanyard to remove the conversion cap Fig 25 NOTE Do not pull inflation lanyard when removing conversion cap FIGURE 25 To remove the c
7. MUSTANG SURVIVAL INFLATABLE VEST WITH LIFT Owner s Manual MD0450 22 Inflatable Vest with LIFT Hydrostatic Inflation Model Manual with Automatic Backup SecureZIP US Patent No 6 832 415 and Patents Pending CONTENTS Page 1 Introduction 1 Why are PFDs Required Safety Equipment 2 What is an Inflatable PFD 3 Instructions for Use 3 Component Inspection Instructions 4 Readiness Checklist 5 Donning Instructions 6 Inflation 8 In water Adjustments 9 Special Considerations for Automatic Devices 10 Deflation 10 Usage Below Freezing 11 Re arming Your PFD 15 Auto Manual Conversion Cap MA7219 Instructions 15 Conversion Instructions 17 Repacking 23 Is Your PFD in Good and Serviceable Condition 24 Care and Maintenance Instructions 26 Cleaning and Storing 26 How and Why to Test Your PFD 27 How Do You Test Your PFD Using the Automatic Inflator 27 How Do You Test Your PFD Using the Manual Inflator 28 How Do You Test Your PFD Using the Oral Inflator 29 Wear Your PFD 30 Hypothermia 31 Each of These Devices is Intended to Help You Save Your Life 32 Safety Accessories 32 Do Not Attach PFDs to Your Boat 32 Airline Operator Policy on Carriage of Inflatable PFDs Inflatable Vest with LIFT Owner s Manual INTRODUCTION The MD0450 22 requires user involvement to ensure a level of safety equal to other inflatable PFDs Knowledgeable users increase their safety significantly by wearing and using these PFDs as prescribed in thi
8. Vest with LIFT you will need your fully armed Inflatable Vest with LIFT and re arming kit approved for your Inflatable Vest with LIFT MA7218 22 2 Put on the Inflatable Vest with LIFT 27 MUSTANG SURVIVAL Actuate the inflation system by jerking firmly downward on the beaded handle The Inflatable Vest with LIFT should fully inflate within 5 seconds Get into shallow water just deep enough that you can stand with your head above the surface See if the Inflatable Vest with LIFT will float you on your back or just slightly back of vertical In a relaxed floating position verify that your mouth is well above the water s surface Note the effect of where you hold your legs and how you float Get out of the water and remove the Inflatable Vest with LIFT Completely deflate the Inflatable Vest with LIFT using the oral inflator see Deflation p 10 Let the Inflatable Vest with LIFT dry thoroughly Re arm p 11 and Repack the PFD p 17 HOW DO YOU TEST YOUR PFD USING THE ORAL INFLATOR This test is not mandatory however may be conducted using the following procedure WARNING Use only a previously fired hydrostatic inflator to perform this test DO NOT test with a fully armed hydrostatic inflator as double inflation may occur possibly resulting in cell damage No spare parts or re arming kits are needed to test your Inflatable PFD Put on the Inflatable Vest with LIFT Get into shallow
9. become incapacitated due to hypothermia the PFD will keep you afloat and greatly improve your chances of rescue 2 Do not attempt to swim unless it is to reach a nearby craft fellow survivor or a floating object on which you can lean or climb Swimming increases the rate of body heat loss In cold water drown proofing methods that require putting your head in the water are not recommended Keep your head out of the water This will greatly Inflatable Vest with LIFT Owner s Manual 30 lessen heat loss and increase your survival time 3 Use the standard H E L P position when wearing an inflatable PFD drawing the legs up to a seated position because doing so will help you conserve body heat Fig 36 4 Keep a positive attitude about your survival and rescue This will improve your chances of extending your survival time until rescued Your will to live does make a difference 5 If there is more than one person in the water huddling is recommended while waiting to be rescued This action tends to reduce the rate of heat loss and thus increase the survival time FIGURE 36 EACH OF THESE DEVICES IS INTENDED TO HELP YOU SAVE YOUR OWN LIFE For your PFD to function properly follow these suggestions to verify that it fits floats and remains in good condition 1 Check the inflation mechanism status indicator before each use 2 Get in the habit of re arming the inflation mechanism immediately after each CO in
10. e cartridge may be carried by a passenger or crew as checked baggage Please refer to the governing body s documentation found online at http www phmsa dot gov Inflatable Vest with LIFT Owner s Manual 32 WE SAVE LIVES FOR A LIVING www mustangsurvival com 3870 Mustang Way TOLL FREE 1 800 526 0532 Bellingham WA EMAIL mustangusa mustangsurvival com USA 98226 WEB www mustangsurvival com Mustang Survival and seahorse design are registered trademarks of Mustang Survival Corp Our commitment to quality has earned our Richmond facilities ISO 9001 registration the highest of all international standards This is our guarantee you re receiving the ultimate in design and manufacturing Printed in Canada Rev 30 Mar 07
11. eft and right panel covers for full inflation because oral inflation may not provide sufficient pressure to open the tabs Re arming Your PFD NOTE A valid re arm kit MA7218 22 is required for this procedure 1 Place the Inflatable Vest with LIFT on a smooth flat surface and wipe off any water Access the inflator by reaching under the cover and fully expose the inflator for re arming Hold the CO cylinder through the fabric using one hand Fig 12 FIGURE 12 N 11 MUSTANG SURVIVAL 2 Insert the metal key between the black locking ring and labeled yellow cap Turn the key counter clockwise Fig 13 Locking Ring Key 3 Turn the black locking ring counter clockwise and lift off the cap yellow inflator operating head Fig 14 Dispose of the used cap FIGURE 14 Cap 4 Squeeze the sealing ring to elongate and remove the inflator body Fig 15 Inflatable Vest with LIFT Owner s Manual 12 FIGURE 15 Red Indicator Inflator Body Sealing Ring FIGURE 16 6 Check that the new inflator body indicator is green Insert the new inflator body with CO cylinder pointing upward inside the Inflatable PFD Fig 17 Let the sealing ring rest on the adapter around the four lugs FIGURE 17 Green Indicator gt Caution Do not turn the center shaft 13 MUSTAN
12. flatable PFD is much more comfortable to wear than other PFD types Get into the habit of wearing this PFD Non swimmers and children especially should wear a hybrid or non inflatable PFD at all times when on or near the water 29 MUSTANG SURVIVAL HYPOTHERMIA Prolonged exposure to cold water causes a condition known as hypothermia a substantial loss of body heat which leads to exhaustion and unconsciousness Most drowning victims first suffer from hypothermia The following chart shows the effects of hypothermia how hypothermia affects most adults How hypothermia affects most adults Water Exhaustion or Expected Temperature C F Unconsciousness Time of Survival 0 3 33 Under 15 min Under 15 45 min 0 3 4 33 40 15 30 min 30 90 min 4 10 40 50 30 60 min 1 3 hrs 10 16 50 60 1 2 hrs 1 6 hrs 16 21 60 70 2 7 hrs 2 40 hrs 21 27 70 80 2 12 hrs 3 hrs to Indefinite Over 27 over 80 Indefinite Indefinite PFDs can increase survival time because they allow you to float without using energy treading water and because of their insulating properties Naturally the warmer the water the less insulation you will require When operating in cold waters below 60 F 15 6 C you should consider using a coat or jacket style PFD or a Type V Thermal Protective PFD as they cover more of the body than the vest or belt style PFDs Some Points to Remember About Hypothermia Protection 1 Always wear your PFD Even if you
13. flation be sure the inflator is dry before re arming 3 Try your wearable PFD on and adjust it until it fits comfortably in and out of the water 4 Mark your PFD with your name if you are the only wearer 5 Do not alter your PFD If it doesn t fit properly get one that does 6 Your PFD is not intended for use as a fender or kneeling pad 31 MUSTANG SURVIVAL 7 If your PFD is wet allow it to dry thoroughly before storing it Store it in a well ventilated area 8 Do not dry your PFD in front of a radiator or other source of direct heat SAFETY ACCESSORIES For the MD0450 22 use a MA7218 22 Re arm Kit which includes a 38 gram CO replacement cylinder inflator body and beaded handle DO NOT ATTACH PFD S TO YOUR BOAT Each PFD has straps hooks buckles or other means for securing the device in place on the wearer Some PFDs also incorporate decorative D rings or tabs Such items are not to be used to attach the device to the boat Attaching the device to the boat will not permit it to perform as intended AIRLINE OPERATOR POLICY ON CARRIAGE OF INFLATABLE PFDS AND CO CARTRIDGES Please be aware that the following regulations apply to the air transport of this product According to U S Department of Transportation DOT PHMSA the Pipeline and Hazardous Materials Safety Administration Title 49 CFR 75 10 a 25 With the approval of the aircraft operator one small carbon dioxide cylinder not installed plus one spar
14. maximum mobility with minimum bulk The Inflatable Vest with LIFT can be inflated either automatically during immersion manually by pulling a beaded handle or by mouth It is imperative that you familiarize yourself with the procedures outlined in INSTRUCTIONS FOR USE p 3 Inflatable Vest with LIFT Owner s Manual INSTRUCTIONS FOR USE This manual supplies instructional maintenance and safety information for model MD0450 22 unless specified otherwise The model number is listed on the label FIGURE 1 MD0450 Unpacked FOLD 1 FoLb 2 Beaded f Waist Belt Foi 2 eo Handle L q Pees Front Buckle Left Lobe Right Lobe FIGURE 2 Hydrostatic Inflator Cap Water Inlet Valve Black Locking Ring cee wa E telae C m Yellow Inflator Cap iia Cap Locking Ring FR abs ing Point Lanyard Status Indicator Inflator Body Expiry Beaded Date Handle Component Inspection Instructions 1 Examine the single point indicator through the window panel Ensure the single point indicator is green If the single point indicator is red the mechanism has been fired or is incorrectly fitted Fig 2 See 3 MUSTANG SURVIVAL RE ARMING YOUR PFD p 11 NOTE The single point indicator must be green before proceeding Open the cover at wearer s right hand side of the chest and lay the device flat Ensure the oral inflati
15. nflatable Vest with LIFT Owner s Manual 6 firmly downward The PFD should fully inflate within 5 seconds Fig 6 NOTE Deflation may occur if the CO cylinder is removed while the Inflatable Vest with LIFT is inflated FIGURE 6 2 Fasten the chest straps Fig 7 and adjust to a snug fit Important Ensure the chest buckle is fastened when inflated FIGURE 7 Fastened Chest Strap Automatic Backup Inflation Inflation will occur automatically within 5 seconds after the inflator is immersed in water Hydrostatic pressure opens the water inlet valve allowing the water sensing element to disintegrate triggering a spring loaded plunger which punctures the CO cylinder inflating the Inflatable Vest with LIFT Fig 7 7 MUSTANG SURVIVAL NOTE Hydrostatic inflator must be submerged in at least 4 inches of water to activate the inflator NOTE When inflated the carbon dioxide CO gas used to inflate PFDs will slowly escape through the cell over time A slight reduction of pressure will be observed after several hours of inflation Topping up by oral inflation may be required in the event of prolonged immersion Oral Inflation Properly armed and inspected Inflatable Vest with LIFT PFDs will inflate when manually or automatically activated However you can fully inflate the PFD by mouth Fig 8 should inflation not occur or if you are in a
16. o that the Inflatable Vest with LIFT is laid out flat Fig 27 shows the right lobe as worn FIGURE 27 FOLD 1 FOLD 2 Right Lobe Inflatable Vest with LIFT Owner s Manual 18 4 Lay out flat the right lobe as it is worn Shift the left lobe as it is worn on the waist belt to fully extend the right lobe for folding NOTE The numbered fold lines on the diagram are provided to assist with packing Make each fold towards yourself 5 Fold the right lobe as it is worn over on the Fold 1 dashed line Fig 28 Note that the right lobe has the inflator with cylinder FIGURE 28 Right Lobe 6 Continuing with the right lobe fold it over on the Fold 2 dashed line Fig 29 Ensure that the bladder is tucked under the inflator to prevent it from blocking the indicator window Point A FIGURE 29 19 MUSTANG SURVIVAL 7 Fold the bottom portion of the lobe over Fig 30 a Position the lobe so it does not cover the inflator Point A b Put the inflator beaded handle through the opening in the cover Point B and attach to the Velcro tab c Position the chest buckle under the cover Point C FIGURE 30 8 Fold the lobe over on the Fold 3 dashed line Fig 31 a Position the folded lobe so it does not cover the inflator Point A FIGURE 31
17. on dust cap is in the stowed position Fig 22 Ensure the single point indicator is green and the beaded handle is attached to it s Velcro tab secure the zippers on the Inflatable Vest with LIFT see Repacking p 17 Ensure the date on the inflator is not five years or older Fig 2 If it is replace the inflator see Re arming Your PFD p 11 Readiness Checklist Check your Inflatable Vest with LIFT and ensure all of the checkpoints listed below are true before each use Single point indicator is green Ensure the current date is not past the date on the inflator If it is replace the inflator see Re arming Your PFD p 11 All zippers Velcro and waist buckle are securely fastened Inflatable Vest with LIFT is not twisted Oral inflation dust cap is in the stowed position Fig 22 Ensure the beaded handle is placed through the opening and is attached to the Velcro tab on the outside of the vest Fig 35 No rips tears or holes all seams are securely sewn and the fabric straps and hardware are still strong Your Inflatable Vest with LIFT is ready for use if all boxes are checked NOTE Contact your Mustang Dealer if you have any concerns about the readiness of your Inflatable Vest with LIFT Inflatable Vest with LIFT Owner s Manual Donning Instructions It is important that the PFD is properly adjusted to fit the person wearing it An inco
18. onversion cap when packed pull the conversion cap lanyard out from the opening of the cover of the LP s right lobe Visually confirm the conversion cap has been removed from the valve opening Place the conversion cap in the anti chafing cover in the front pocket when not in use Repacking IMPORTANT Carefully read the entire Repacking instructions to achieve a properly packed Inflatable Vest with LIFT If your Inflatable Vest with LIFT has been used and or the hydrostatic inflator replaced always inflate through the oral tube and check that it stays inflated at least overnight With the dust cap in the top of the oral tube gently squeeze the Inflatable Vest with LIFT until all air or gas has been expelled Fig 11 Do not wring or twist the Inflatable Vest with LIFT Put the oral tube dust cap back in its stowed position on the oral tube Fig 26 Let the life jacket dry before packing 17 MUSTANG SURVIVAL 1 Before repacking Completely deflate the Inflatable Vest with LIFT see Deflation p 10 NOTE Before following the repacking sequence be sure to properly re arm your Inflatable Vest with LIFT See Re arming Your PFD p 11 2 Ensure the oral inflation dust cap is fitted in the stowed position Fig 26 FIGURE 26 Dust cap Dust cap in stowed position for position deflation 3 Open both front panel covers Adjust the waist belt and chest belt buckles to their full lengths s
19. ot exhibit deterioration that could diminish its performance such as broken or deformed hardware detached webbing rotted structural components air leaks or nonfunctional inflators Unless worn inflated this PFD must also be properly armed with a cylinder installed in the inflator and single point status indicator showing green See Page 3 for instructions Failure to follow these instructions rigorously could result in a non functioning PFD causing injury or death Check the following at the intervals listed below 1 Before Each Use i Examine the single point status indicator through the window panel ensuring it is green If the indicator is red the mechanism requires service See Re arming Your PFD p 11 ii Ensure the manual beaded handle is accessible iii Visually examine your Inflatable Vest with LIFT for damage or excessive abrasion wear tear or contamination Particular attention must be paid to the stitching straps and hardware If in doubt send it to your Mustang dealer for evaluation and or servicing 2 Every Six 6 Months i Leak Test The Inflatable Vest with LIFT should be tested for general leakage by orally inflating your Inflatable Vest with LIFT Inflatable Vest with LIFT Owner s Manual 24 25 until firm and let stand 2 hours A leaking Inflatable Vest with LIFT will not hold its firmness and should be replaced If your Inflatable Vest with LIFT leaks take it to your Mustang dealer fo
20. r evaluation and or servicing Repack the Inflatable Vest with LIFT as outlined in the Repacking section p 17 ii Oral Inflation Valve Test To check the oral inflation valve fully inflate the Inflatable Vest with LIFT using the oral inflator and hold valve under water If bubbles appear deflate and re inflate to test again Should the leak persist take your Inflatable Vest with LIFT to your Mustang dealer for evaluation and or servicing CAUTION To avoid accidental inflation don t allow the water to contact the hydrostatic inflator iii Perform a thorough visual examination See Readiness Checklist p 4 Perform these tests more often if exposed to potential damage or used in extreme conditions After Each Inflation Re arm the Inflatable Vest with LIFT See Re arming Your PFD p 11 Annually Perform the following at the beginning of each boating season after inflation or whenever the integrity of the Inflatable Vest with LIFT is in doubt i Check all components for dirt or corrosion Clean or replace as neccessary See Readiness Checklist p 4 ii Visually examine your Inflatable Vest with LIFT for damage or excessive abrasion wear tear or contamination Particular attention must be paid to the stitching straps and hardware If in doubt send it to your Mustang dealer for evaluation and or servicing iii Perform the Leak Test See the Leak Test section 2 i in the Care and Maintenance
21. remature automatic inflation causes several risks that you must address to avoid drowning Much less common but also important are Double inflation CO cylinder inflation after full oral inflation could damage the PFD Inflation when stored in a tight space could damage the PFD and The PFD could inflate when you are in an awkward place or position If this PFD should inflate a re arm kit MA7218 22 with a valid install by date is required to re arm the device IMPORTANT The PFD should be re armed according to the Re arming Your PFD instructions p 11 Deflation 1 To deflate the Inflatable Vest with LIFT reverse the oral inflation tube dust cap and insert it into the valve or depress valve with a fingertip The dust cap will not lock in the deflate position so it is necessary to hold it in place Fig 11 Gently squeeze the Vest until all air or gas has been expelled Fig 11 Do not ring or twist see Re arming Your PFD p 11 and Repacking p 17 sections of this manual FIGURE 11 L oral inflation tube Inflatable Vest with LIFT Owner s Manual 10 Usage Below Freezing When the temperature is below freezing a fully discharged cylinder may not adequately inflate your Inflatable Vest with LIFT Under these conditions use the oral inflator to top up the Inflatable Vest with LIFT It may be neccessary to manually release the Velcro tabs located at the bottom of the l
22. rks e A flow of bubbles should not appear see CARE AND MAINTENANCE INSTRUCTIONS for leak tests p 24 It should inflate quick and easily Learn how it works by Inflatable Vest with LIFT Owner s Manual 26 e Activating the CO inflation system e Re arming the CO inflation system e Using the oral inflator tube HOW DO YOU TEST YOUR PFD USING THE AUTOMATIC INFLATOR To test your Inflatable Vest with LIFT you will need your fully armed Inflatable Vest with LIFT and re arming kit MA7218 22 approved for your Inflatable Vest with LIFT Put on the Inflatable Vest with LIFT Get into shallow water just deep enough that you can stand with your head above the surface Once the inflator is underwater 4 inches or so the Inflatable Vest with LIFT should fully inflate automatically within 5 seconds See if the Inflatable Vest with LIFT will float you on your back or just slightly back of vertical In a relaxed floating position verify that your mouth is well above the water s surface Note the effect of where you hold your legs on how you float Get out of the water and remove the Inflatable Vest with LIFT Deflate the Inflatable Vest with LIFT by depressing the oral inflator valve see Deflation p 10 Remove the used inflator Let the Inflatable Vest with LIFT dry thoroughly Re arm p 11 and Repack the PFD p 17 HOW DO YOU TEST YOUR PFD USING THE MANUAL INFLATOR 1 To test your Inflatable
23. rrect fit or improper fastening of attachments could reduce its effectiveness 1 Put the Inflatable Vest with LIFT on just like a jacket Fig 3 If the Inflatable Vest with LIFT is already inflated prior to donning it may be excessively tight while donning If so expel some air by depressing the oral tube valve don the Inflatable Vest with LIFT and refill Inflatable Vest with LIFT by mouth using the oral tube 2 Fasten the front waist belt buckle Fig 3 Adjust the waist belt to a secure fit using the front adjuster on the belt WARNING Do not wear the Inflatable Vest with LIFT under other clothing or harness systems as the inflation could be restricted and you could be injured FIGURE 3 NOTE Heavy objects in the pockets may cause the PFD to sink if dropped overboard when not inflated 5 MUSTANG SURVIVAL 3 Fasten the middle buckle Fig 4 Adjust the middle belt to a secure fit using the front adjuster on the belt FIGURE 4 IMPORTANT Ensure the chest buckle is fastened when inflated Fig 4 4 Feed the loose end of the waist belt into the belt opening in the storage pocket Fig 5 FIGURE 5 Inflation It is recommended that the following procedures be followed to inflate your Inflatable Vest with LIFT Manual Inflation 1 Activate the inflation system by grasping the beaded handle and jerk I
24. s owner s manual General This Inflatable PFD will turn most wearers from a face down to a face up position and provide support suitable for offshore conditions See page 11 for re arming instructions This Inflatable PFD was designed to be more comfortable and less restrictive to wear than inherently buoyant PFDs When worn used and serviced according to this owner s manual this PFD can greatly increase your chances of survival in the water Not recommended for non swimmers or weak swimmers To be considered serviceable this PFD shall not exhibit deterioration that could diminish its performance such as broken or deformed hardware detached webbing rotted structural components air leaks or nonfunctional oral inflation tube Unless worn inflated this PFD must also be properly armed with a full CO cylinder inflation system status indicator and a manual inflation beaded handle accessible outside the user s right front panel cover Fig 1 The chest buckle on the Inflatable Vest with LIFT must be fastened after inflation WHY ARE PFDS REQUIRED SAFETY EQUIPMENT Drownings are the leading cause of fatalities involving recreational and commercial vessels A PFD provides flotation to help keep your head above water help you to stay face up in the water and increase your chances for survival and rescue Most adults only need an extra 7 to 12 kg 3 2 to 5 5 pounds of flotation to keep their heads above water The proper size PFD
25. tside of the vest Fig 39 Ensure the zipper is closed to the stop located under the Velcro tab NOTE Ensure the chest buckle does not extend outside of the Inflatable Vest with LIFT Owner s Manual 22 lobe it should sit under the cover 14 Repeat steps 3 12 for the left lobe as it is worn Note that the left lobe does not have an inflator or indicator window 15 Turn over the Inflatable Vest with LIFT and fold the back flap up and fasten the three 3 Velcro tabs Fig 38 FIGURE 38 b 16 Use the adjustable waist belt to size to fit When complete the garment should appear as shown Fig 39 and be secure for use or storage FIGURE 39 909000909 90009002 Po2o20900 080208054 faoedd 393800020 02000900 00090009 20009090 1020908020 23 MUSTANG SURVIVAL IS YOUR PFD IN GOOD AND SERVICEABLE CONDITION Check your PFD between outings to be sure that it is properly armed as shown by green single point indicator that it is free of rips tears or holes that all seams are securely sewn and that the fabric straps and hardware are still strong Inspect the inflatable portion of the PFD in accordance with the CARE AND MAINTENANCE INSTRUCTIONS p 24 CARE AND MAINTENANCE INSTRUCTIONS It is the responsibility of the wearer to be sure this PFD is in serviceable condition To be considered serviceable this PFD shall n
26. will properly support the weight of the wearer Since this Inflatable PFD does not have inherent buoyancy it provides flotation only when inflated Familiarize yourself with the use of this 1 MUSTANG SURVIVAL Inflatable PFD so you know what to do in an emergency WHAT IS AN INFLATABLE PFD Congratulations on the purchase of your Inflatable Vest with Patent Pending LIFT Life saving Inflatable Flotation Technology LIFT is different from all other inflatable PFD s In general inflatable PFD s are designed to suspend a user s head above water to prevent drowning The Inflatable Vest with LIFT provides freeboard that far exceeds the minimal 3 generally provided LIFT elevates you to an upright safe position and delivers up to 9 of freeboard the highest ever seen in a PFD keeping your mouth high above the water line to minimize the risk of mouth immersions Not only is LIFT one of the world s best performing PFD s in wave conditions but it s comfortable too Light and ergonomically designed you can t even tell you re wearing it until you need it While traditional PFDs are inherently buoyant inflatable PFDs like the Inflatable Vest with LIFT rely entirely upon inflation for buoyancy Uninflated the Inflatable Vest with LIFT is comfortable and can be inflated at any time with a 38 gram CO gas cylinder The Inflatable Vest with LIFT is designed to meet the demands of a full protection PFD offering
Download Pdf Manuals
Related Search