Miele KFN 9755 IDE Refrigerator User Manual
Contents
1. Depending on the thickness of the niche walls push the appliance in until the spacers touch the walls 5 8 16 mm wall thickness or the front edges of the hinges are flush with the niche wall 3 4 19 mm wall thickness m Use an open ended wrench adjust the height adjustable feet as needed until the appliance is level m Ensure that the plastic bracket is flush with the front edge of the niche walls This ensures that a space of 1 5 8 42 mm to the front edges of the side walls is kept 51 Installing the appliance This space must also be taken into Attaching the appliance to the account with cabinetry that has a installation niche receding base even if it means that the plastic bracket will project beyond the base of the cabinetry m If the cabinetry has door stops i e to protect from slamming pull the appliance forward by distance h so that a space of 1 5 8 42 mm is created The hinges now project by distance h and the plastic bracket 9 lines up with the front edge of the hinge If the required distance of 1 5 8 42 mm from the body of the m Push the hinged side of the appliance to the front side of the appliance to the niche wall cabinetry side wall is not observed m Screw the long screws the appliance door may not close 4 x 19 mm into all of the hinge properly causing malfunctions plates2. The water supply is not open See Plumbing The indicator light on the ice cube maker is flashing A fault has occurred Contact Miele Technical Service 33 Frequently asked questions The appliance is making noises Issue Possible fault Solution Brrrrr Humming noise made by the These noises are not a compressor This noise can fault get louder for brief periods The noise of the when the motor is switching compressor and the on coolant circulating in the Blubb blubb A gurgling noise can be system is unavoidable heard when coolant is circulating through the pipes Click Clicking sounds are made when the thermostat switches the compressor on and off Sssrrrrr On multi zone and frost free appliances you can sometimes just hear the movement of air circulating inside the appliance Rattling vibrating The appliance is uneven Realign the appliance using a level by raising or lowering the screw feet underneath the appliance The appliance is touching another appliance or piece of furniture Move it away Drawers baskets or shelves are unstable or sticking Check all removable items and refit them correctly Bottles or containers are unstable or knocking against each other Separate them The transport cable clips are hanging loose at the back of the appliance Remove the clips 34 After sa
3. The floor of the refrigerator is wet Possible fault Solution The drain hole is blocked Clean the condensate channel and drain hole 31 Frequently asked questions The alarm sounds Possible fault Solution The appliance door s have been Close the door s open for longer than 60 seconds The alarm sounds and the temperature display for the freezer section flashes Possible fault Solution The freezer door has been opened This has caused the temperature in the too frequently freezer to rise above the set temperature Once the temperature has dropped to the correct level again the alarm will stop and the display will stop flashing A large amount of food is being frozen at the same time Bars light up or flash in the temperature displays Only temperatures within the range of the appliance can be shown in the display Check the display again about 6 hours after turning it on A fault code of F0 to F5 appears in one of the temperature displays A fault has occurred Contact Miele Technical Service The Super indicator light for the freezer section and the temperature display are both flashing A fault has occurred Contact Miele Technical Service The Super indicator light for the freezer section is not on but the refrigerator is running Possible fault Solution The indicator light is faulty Contact Miele
4. This is not a fault The suction caused by opening and closing the door too many times in succession prevents it from opening Wait a few minutes then try again It should now open without force The compressor kicks on very frequently and for too long Possible fault Solution The ventilation slits are covered or dusty Clean with a vacuum or brush The doors have been opened too frequently or a large amount of fresh food has been put in at once for freezing Once the fridge freezer gets down to the set temperature the compressor will turn off The door is not closed Check that the doors have been closed properly The compressor runs continuously To save energy the compressor runs at a lower speed but for longer when less cooling is required This is not a fault The appliance will not turn off The safety lock has been activated See Safety Lock The interior lighting of the refrigerator section is not working Possible fault Solution The refrigerator door has been left open for too long The lighting turns itself off automatically after approx 15 minutes If the lighting does not come on when the door is opened briefly but the temperature display is working then the lighting is defective Contact Miele Technical Service The LED lighting should only be repaired replaced by a Miele service technician Danger of injury or damage
5. Do not move the ground plug Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Improper connection of the equipment grounding conductor may result in electric shock If you are in any doubt as to whether the appliance has been properly grounded have the appliance checked by a qualified electrician or service technician Installation repairs and other work by unqualified persons could be dangerous The manufacturer will not be held responsible for damage or injury arising from unauthorized work Before installing the appliance verify that the voltage load and circuit rating information found on the data plate match the household electrical supply If there are any questions regarding the electrical connection of this appliance to the power supply please consult a licensed electrician or call the Miele Technical Service SA 1 800 999 1360 CDN 1 800 565 6435 The appliance comes with a UL listed 3 wire power supply cord The appliance requires a 3 wire receptacle The receptacle must be installed by a licensed electrician only In the case of side by side installations a separate outlet must be used for each appliance Ideally the power outlet should be next to the appliance and easily accessible Do not connect the appliance to the power supply by an extension cord Extension cords do not guarantee the requ
6. m Open the plastic bracket and screw a long screw 2 4 x 19 mm through the middle of the long hole m Close the plastic bracket 52 Installing the appliance Mounting the custom door panels m Set a gap of 5 16 8 mm between the appliance door and the fixing bracket m Slide the mounting aids 2 to the m Screw the screw through the fixing bracket height of the custom door The lower edge X of the mounting aids must be m Push the bracket towards the niche at the same height as the upper edge wall and tighten the screws of the custom door to be mounted m Close the bracket see A in the illustration m Close the appliance doors m Unscrew the nuts 3 remove the fixing bracket and the mounting aids 53 Installing the appliance amp i I HM V Ill iN TEN Ni FA Hd NAI LL UE UV AM BN m With a pencil lightly mark a line down the center of the inside of the custom door m Hang the fixing bracket with the mounting aids on the inside of the custom door Align the bracket centrally m Secure the fixing bracket with at least 6 screws 4 x 14 mm For framed doors use only 4 screws at the edge m Carefully pull the mounting aids up and out m Turn them around and fit them into the middle slots of the fixing bracket
7. Niche height B KFN 9755 iDE 27 3 8 695 mm 69 3 4 70 3 8 1772 mm 1788 mm 44 Adjusting the door hinges The door hinges are pre adjusted so If you would like to cushion the doors that the appliance doors can be for a more gentle opening you can opened wide increase the spring force of the appliance door By adjusting the hinges the doors can be modified so they do not open as far For example when the door is opened if an adjacent wall or piece of furniture is in the way the door angle should be limited to 90 m Insert the pins supplied into the hinges from above This will limit the opening angle of the appliance door to 90 amp To reduce the opening angle m Turn the Allen wrench provided clockwise This will tighten the hinge making it harder to open the door wide 8 To open the door fully m Turn the Allen wrench provided counterclockwise 45 Adjusting the door hinges Before installing the appliance you will need to decide which side of the door you would like hinged For and left handed door hinge follow the instructions below Tools needed a Philips head screwdriver aflathead screwdriver various sizes of Torx screwdrivers an open ended wrench m Open the appliance doors m Using a flathead screwdriver lift and remove the covers and 3 as well as the plugs 46
8. for safe keeping 54 m Hang the custom door on the adjusting bolts 8 m Loosely attached the nuts 3 onto the adjusting bolts m Close the door Check the distance between the custom door and adjacent cabinetry doors m Align the custom door with the adjacent cabinetry doors Side adjustments X are achieved by sliding the cabinetry door Height adjustments Y are achieved by turning the adjustment bolts with a flathead screwdriver m Tighten the nuts Installing the appliance Securing the appliance door to the custom door panel m Secure the fixing bracket using the pre drilled holes using the 4 x 14 mm screws Ensure that the two metal edges are flush symbol Align depth Z on the custom door Loosen the screws at the top of the appliance doors and the bottom of the fixing bracket Adjust the custom door to create a space of 1 16 2 mm between the custom door and the front edge of the niche m Close both the doors and align them with the adjacent cabinetry doors m While holding the adjusting bolts with a screwdriver tighten the nuts on the appliance doors using a wrench The cover strip amp must not protrude it must be completely inside in the niche m Re tighten all the screws m Secure the appliance again at the bottom with a screw 9 through the round hole in the plastic bracket 49 m Close the plastic
9. After your appliance is in operation do not touch the cold surfaces in the machine ice cubes or frozen food particularly when hands are damp or wet Skin may adhere to extremely cold surfaces P Do not refreeze frozen foods which have thawed partially or completely P Do not handle frozen food or ice with wet hands Danger of injury P Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance P Do not use sharp edged objects to remove frost and ice or separate frozen foods and remove ice trays They will damage the evaporator causing irreversible damage to the appliance P Do not use defrosting sprays or de icers as they might contain substances which could damage the plastic parts or which could cause a build up of gases and pose a danger to health P Do not use any oils or grease on the door seal as these will cause the seal to deteriorate and become porous with time P Do not block the ventilation gaps in the plinth or the top of the appliance housing unit as this can impair the efficiency of the appliance increase the electricity consumption and cause damage to the appliance P Never use a steam cleaner to clean the appliance Pressurized steam could damage electrical components and cause a short circuit IMPORTANT SAFETY INSTRUCTIONS Disposal of your old appliance P Before disposing of an old appliance first make the doo
10. 2 38 mm must be provided behind the appliance The air intake to the appliance is made through the base of the installation niche The ventilation cross section must be at least 78 3 4 200 cm to ensure that the warm air can escape without obstruction The air intake and outlet must not be blocked or covered in any way They also need to be dusted cleaned on a regular basis Before installation m Remove the cover strip the sealing strip and other accessories from the inside and from the exterior rear wall of the appliance m Do not remove the spacers from the rear wall of the appliance They ensure that there is enough space between the rear wall of the appliance and the wall m Remove the cable clips from the rear of the appliance m Check that all the parts on the rear the appliance can move freely Bend any parts carefully if needed Did the old appliance have a different hinge system Even if your old appliance had a different hinge system you can still use a custom door panel m Un install the old hinges they are no longer necessary the custom door panel will be mounted on the appliance door All necessary parts are included with the appliance or can be ordered from Miele 43 Dimensions m CN v Fo ES N co VI 2783 4 12 2200 cm Freezer section height A
11. CO ds 3 m Press the main switch on the right side of the control panel 10 The temperature display for the refrigerator section lights up and the interior lighting comes on when the door is opened Bars light up in the freezer section display until the selected temperature is reached The appliance begins cooling Allow the appliance to run for a few hours before placing food in it This will enable it to sufficiently cool Cool pack Place the cool pack in the top freezer drawer The cool pack will be at maximum performance after it has been in the freezer for approx 24 hours Turning the appliance off m Press the main switch on the right side of the appliance until both temperature displays go out If the cooling system does not turn off the safety lock has been activated Before use Turning the appliance On Off Turning the refrigerator section off The refrigerator section can be turned off separately while the freezer section remains on e g during vacation CO Sem gt N m Press the On Off button on the left side of the control panel until the temperature display for the refrigerator section goes out Turning the refrigerator section on m Press the On Off switch on the left side of the control panel until temperature display for the refrigerator section turns on The refrigerator section will begin to cool and the interior lighting will turn on when the door is opened Safety
12. Technical Service 32 Frequently asked questions nA appears in the temperature display for the freezer section Possible fault Solution The temperature in the freezer section has risen too high at some point during the last few days because of a power failure m Press the alarm off button while nA is lit in the display The display will show the warmest temperature reached in the freezer during the power failure for about 1 minute The display will then revert to the current temperature in the freezer section After the power failure the appliance will continue running at the last temperature set there is no need to re set The ice cube maker will not turn on Possible fault Solution The appliance is not plugged in Check that the appliance is connected to the power supply The ice cube maker is not producing any ice cubes Possible fault Solution When the appliance is turned on for the very first time it can take up to 24 hours for the first ice cubes to drop out of the container ice cube maker and collect in the The water supply line was not primed purged of air before the appliance was used for the first time Contact Miele Technical Service The appliance is not turned on Check that the appliance is switched on using the main switch on the right side The ice cube maker is not turned on See Ice cube maker Turning on
13. The temperature can be set as usual with the temperature selection buttons 18 DynaCool should also be selected if the room temperature is high above approx 86 F 30 C and the humidity level is high Turning on DynaCool C 4 oss 3 m Press the DynaCool button the indicator light will turn on Turning off DynaCool m Press the button for DynaCool button the indicator light will go out When the door is open the fan automatically turns off Using the refrigerator efficiently Different storage zones Due to the natural circulation of air in the appliance there are different temperature zones in the refrigerator Cold heavy air sinks to the lowest section of the appliance Make use of these different zones when placing food in the appliance This appliance uses a dynamic cooling feature DynaCool to establish a constant temperature during cooling As a result the differences between temperature zones are less pronounced Leave some space between items so that air can circulate freely around them Do not cover the fan in the rear wall this is important for cooling performance Warmest area The warmest area is in the top section of the door Use this area to store items such as butter and cheese Coldest area The coldest area in the refrigerator section is directly above the fruit and vegetable drawers Use these cold areas in the refrigerator for all highly perishable fo
14. a clean wet cloth then dry with a soft cloth Leave the appliance doors open for a short time so the moisture can evaporate m Clean the stainless steel surfaces with a suitable stainless steel cleaner available from Miele This will help protect the stainless steel and prevent resoiling 27 Cleaning and Care Cleaning the ice cube tray The ice cubes are formed in a tray before they are dropped into the drawer The tray should be cleaned regularly to remove any stale ice or water m Connect the appliance to the electrical supply m Press the On Off button for the ice cube maker the indicator light will turn on m Empty the ice cube drawer m Press the On Off button for the ice cube maker for approx 10 seconds after approx 1 second the ice maker will turn off and the indicator light will go out The indicator light will flash m Push the ice cube drawer in as far as it will go within the next 60 seconds The ice cube tray will then rotate into an angled position for easier cleaning Wait until the ice cube tray has completed this rotation before continuing 28 m Remove the ice cube drawer m Clean the ice cube drawer and tray with a mild solution of warm water and liquid dish soap m Press the On Off button on the ice cube maker The ice cube tray rotates back into its original position m Replace the ice cube drawer and close The ice cube maker will begin producing i
15. at the desired height m Slide in the glass shelves one after the other The glass shelf with the raised edge should be placed at the back Fruit and vegetable drawers on rollers depending on model The fruit and vegetable drawers are mounted on rollers and can be pulled out for loading unloading and cleaning The rollers can also be removed for cleaning 25 Adjusting the interior fittings Moving the adjustable door shelves m Lift the shelf up and out of the stainless steel frame m Push the stainless steel frame up and remove by pulling it forward m Replace the frame at the desired height Ensure that it is securely pushed back into position m Place the shelf into the frame The shelves can be removed for loading unloading cleaning or serving and then replaced 26 Universal container Food can be stored as well as served in the universal container The universal container consists of a deep tray and a shallow tray 2 Both trays can be fit into the stainless steel frame m o use the universal container to serve food place the shallow tray 2 in the stainless steel frame and use the deep container as a lid Moving the divider depending on model The divider can be moved to the left or right to ensure that bottles are held securely in position when the door is opened and closed The divider can be removed completely e g for cleaning m Lift the front e
16. before installation or use Caring for the environment Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable Please recycle Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation 38 Disposal of an old appliance Old appliances contain materials that can be recycled Please contact your local recycling center about the possibility of recycling these materials Before discarding an old appliance disconnect it from the gas and electrical supply and cut off the power cord to prevent it from becoming a hazard Plumbing All plumbing work should be carried out by a suitably qualified and competent person in accordance with all applicable local and national regulations The manufacturer is not liable for damage to property due to an incorrect installation or water connection The water quality must conform to country requirements for drinking water The appliance is only suitable for connection to the cold water supply Water pressure on site Minimum 14 5 psi Maximum 145 psi if higher install a pressure reduction valve A separate shut off valve must be installed so that the water supply can be interrupted as needed If one is not present have a water valve installed by a licensed plumber It must be easily accessible after the appliance has been b
17. bracket 55 Installing the appliance The following confirms that the appliance is installed correctly The doors close properly The doors do not touch the cabinetry The seal at the upper corner of the hinged side contacts tightly m To verify this place a flashlight in the appliance and close the appliance doors Turn off the lights and check whether the light is visible from inside the appliance If light is seen check the individual installation steps again m Replace the upper cover 1 m Replace the side covers 42 and 3 Be sure all of the covers click into place 56 57 58 59 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www miele com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643 5381 905 660 9936 Fax 905 532 2290 www miele ca info miele ca general enquiries professional miele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 service miele ca technical enquiries Alteration rights
18. lock The safety lock can be activated to prevent the appliance from being turned off accidently Activating Deactivating the safety lock S m Press the Super button for the freezer section for approx 5 seconds The Super indicator light flashes and c flashes in the temperature display ESES m Press the Super button for the freezer section again c will appear in the display m Using the temperature selector buttons you can now choose between c Aand 1 0 safety lock deactivated l safety lock activated m Press the Super button for the freezer section to save the setting The safety lock indicator lights up in the display f when it is activated CO Sum S m Press the main switch on the right side on the control panel to exit the settings mode If a button is not pressed within 2 minutes the electronics will return to normal operation Before use Turning off for longer periods of time If the appliance is not going to be used for an extended time for example during a vacation some precautions should be taken m Shut off the water supply line several hours before switching off the appliance m Take all food out of the appliance m Turn the appliance off at the main switch m Unplug the appliance m Discard any ice cubes m Clean the interior m Leave the doors open to prevent odors 12 Setting the temperature Temperature range The temperature can be selected
19. of time in months in which various foods should be stored If the storage time given on the packaging differs follow the advice on the packaging QWs we U a4 R Type of food Length of time months Cakes ice cream 2 3 stews soups Fish mushrooms 3 5 bread Pork veal poultry 6 8 Beef fruits 10 12 vegetables Defrosting Frozen food can be defrosted in different ways in a microwave oven atroom temperature inthe refrigerator the cold given off by the frozen food helps to keep the other food cold in a steam oven Thin pieces of meat and fish can be placed directly in a hot pan without defrosting Poultry It is especially important to observe proper hygiene when defrosting poultry Never save the liquid from defrosted poultry Drain it away and promptly wash the container the sink and your hands Danger of salmonella poisoning Fruit should be defrosted at room temperature in its packaging or in a covered bowl Most vegetables can be cooked while still frozen Simply place directly into boiling water or hot oil 21 Using the freezer efficiently Cooling drinks quickly To cool drinks quickly turn on the Super function for the freezer See Super for more information Do not leave bottles in the freezer for more than 1 hour closed containers could burst Freezer tray The freezer tray can be used to freeze small items su
20. reserved 1308 KFN 9755 iDE For the most updated manual see the Miele web site M Nr 07 270 130 00
21. wait approx 6 hours or 24 hours for a fully loaded appliance for the temperature display to show an accurate reading If after this time the temperature is still too high or low try adjusting it again Setting the temperature Temperature displays During normal operation the temperature display shows the temperature in the middle of the refrigerator section and the temperature in the warmest part of the freezer section If the temperatures in the appliance are not in the possible temperature display range dashes will flash in the temperature displays 14 The temperature displays flash if a different temperature is being set the temperature in the appliance has risen by several degrees indicating that the appliance is warming up too much This short term loss of cooling is not a cause for concern in the following Cases when the door has been left open for a longer period for example to take out or put in a large amount of food when fresh food is being frozen However if the temperature remains above O F 18 C for a longer period of time you will need to check to make sure that any frozen food has not started to thaw Any food that has started to thaw should be cooked as soon as possible Setting the temperature Temperature display brightness CO Sem The brightness of the temperature display is factory set to the lowest setting However when the door is open
22. Miele Operating and Installation Instructions KFN 9755 iDE To prevent accidents en US CA and machine damage read these instructions before installation or use M Nr 07 270 130 Contents IMPORTANT SAFETY INSTRUCTIONS 20020005 4 Guide to the Fridge Freezer combination 005 8 Before use ees dE eR Saeed a hee Passed rec benedi rura 10 Turning the appliance On Off 0 000 erta ee 11 sre c T 11 Turning off for longer periods of time liii iles 12 Setting the temperature llli sili less 13 Setting the temperature in the refrigerator and freezer sections 13 Temperature dIiSplays ue ns dua dae Re wade ae os d 8e dne o 14 Alarm E aie e Pett eee ee a a ean ae ate eee ee E i 16 LOOK AIAN kre cbe s Md dare Re RU det order is uas Soden Pus dee ee ee 16 T rming the alarmff usa ec x ree E p s Er ed eati m ed 16 Using the Super and DynaCool functions 17 SUPEr UNCION MT rr 17 DYNACOGI By MEME C 18 Using the refrigerator efficiently 00 0004 19 Different storage Zones esan oep Ie ele UPS I UMEN deben 19 Using the freezer efficiently 0 00000022 20 Freezing TOO ereditiera pa detto beth ght odd Pee ng dep tiui PES 20 Freezer calendar dde eed ueber E ede x Ip hen etr listet e ea 21 DEOSING CEPR 21 Freezer iray ss v
23. Possible fault Solution The machine is not turned on Check whether the appliance is switched on at the main switch The appropriate temperature display must be lit up The machine is not plugged in Check that the plug is correctly inserted in the power outlet Check that the fuse has not tripped Reset the circuit breaker The temperature in the refrigerator or freezer section is too low Possible fault Solution Select a warmer temperature See Setting the temperature The Super function is still on The Super function automatically turns off after Refrigerator approx 6 hours Freezer approx 30 60 hours depending on the amount of food frozen The door is not closed Check that the doors are closed properly A large amount of food is being frozen at the same time This makes the compressor run longer causing the temperature in the freezer section to fall automatically The freezer section is too warm Possible fault Solution The room temperature is lower than the ambient temperature for which the appliance is designed Raise the temperature of the room Operating the appliance in a room that is too cold will cause the cooling system to turn off for too long causing the freezer section to become too warm 30 Frequently asked questions The door to the freezer section will not open Possible fault Solution
24. an extension cord to connect this appliance to electricity Extension cords do not guarantee the required safety of the appliance e g danger of overheating P Be certain your appliance is properly installed and grounded by a qualified technician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician The manufacturer cannot be held responsible for damages caused by the lack or inadequacy of an effective grounding system P Only connect power to the appliance when all installation and plumbing work is complete IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top heavy and must be secured to prevent it from tipping forward P Before installation or service disconnect the power supply to the work area by unplugging the unit tripping the circuit breaker or removing the fuse P This appliance must be installed and connected in compliance with the installation instructions P Installation and repair work should be performed by a Miele authorized service technician Work by unqualified persons could be dangerous and may void the warranty P Installation must comply with local plumbing regulations and state laws The manufacturer cannot be held liable fo
25. appliance doors is left open for more than 60 seconds the alarm signal will sound 16 Turning the alarm off Once the set temperature is reached in the freezer the alarm signal turns off and the temperature display stops flashing CA Sus 3 m To turn the alarm off early press the alarm off button The alarm signal turns off The temperature display will continue to flash until the set temperature has been reached The display then stops flashing and lights steadily The alarm system is automatically reactivated Using the Super and DynaCool functions Super function The Super function is used to rapidly reduce the temperature in the refrigerator and freezer sections to their lowest settings depending on the room temperature When used with the refrigerator the Super function is ideal for the rapid cooling of drinks and refrigerating large quantities of food When used with the freezer the Super function is ideal for freezing large quantities of unfrozen food The function should be switched on approx 6 hours before the fresh food is placed in the freezer If the max freezing capacity is used allow 24 hours This helps food to freeze quickly retaining its nutrients vitamins flavor and appearance It is not necessary to use the Super function in the freezer if you are loading frozen food or if you are loading less than 4 4 Ibs 2 kg of food Turning on the Super function for the refrigerator fre
26. ce cubes again after a maximum of 6 hours If the ice cube maker has not been used for an extended period of time it is important to clean the ice cube tray before using it again Ventilation slits m Check the ventilation slits regularly Remove any dirt dust with a vacuum cleaner or brush Clean as needed Cleaning and Care Door seal Do not use oil or grease on the door seals This may cause the seals to deteriorate and become porous over time m Clean the door seals with warm water and dry thoroughly After cleaning m Return all shelves drawers and accessories m Place food back in the refrigerator section close the appliance door insert the plug in the power outlet and turn the appliance on m Turn on the Super function for the freezer to cook the freezer section quickly The indicator light will come on m Once the freezer has reached a constant of O F 18 C or colder place the food back in the drawers and replace them in the freezer section and turn off the Super function 29 Frequently asked questions With the aid of the following guide minor problems can be corrected without a service call Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations Unauthorized repairs could cause personal injury or machine damage and may void the warranty The refrigerator or freezer section does not get cold
27. ch as berries herbs and vegetables They are frozen individually and therefore maintain their shape when defrosted m Load the items loosely onto the freezer tray o Be X m Hang the tray on one of the upper freezer drawers Allow 10 12 hours for the items to freeze thoroughly Then transfer them to a suitable container or bag 22 Cool pack The cool pack prevents the temperature in the freezer from rising too quickly in the event of a power failure Place the cool pack in the top freezer drawer directly on top of the food The pack will be at its most effective after approx 24 hours If there is a power failure the cool pack will help keep food cold as long as possible When placing fresh food in the freezer use the cool pack to separate the fresh food from the already frozen food This will prevent the frozen food from beginning to thaw Ice cube maker For the automatic ice cube maker to operate it must be connected to the household water supply See Plumbing Turning on m Turn the appliance on with the main switch m Open the top left drawer of the freezer section dd O ep m Press the On Off button on the ice cube maker The indicator light will turn on m Close the drawer Ice cubes will not be produced unless the drawer is completely closed After the appliance is turned on for the very first time it can take up to 24 hours for the first ice cubes t
28. densate is drained away via a channel and drain hole into an evaporation system at the back of the appliance Be sure that the condensate channel and drain hole are kept clean and are unblocked so that condensate can flow away easily 24 Freezer section The freezer defrosts automatically The moisture generated in the appliance collects on the condenser and is automatically defrosted and dissipated by the condenser from time to time This automatic defrosting system enables the freezer to remain permanently ice free however the food stored remains frozen Adjusting the interior fittings Moving the shelves The shelves can be adjusted according to the height of the food m Lift the shelf pull it forwards slightly until the notch at the side is in line with the shelf support It can now be moved up or down as desired The raised edge at the back of the shelf must face upwards to prevent food from touching the back of the appliance Stops prevent the shelves from unintentionally being pulled out too far Split shelf To accommodate tall items such as tall bottles or containers one of the shelves is divided The front section can be gently pushed under the rear section m Pull the front half of the glass shelf forwards slightly then slide it carefully under the rear half To move the split shelf m Remove both halves of the glass m Fit the brackets onto the support on the left and right sides
29. dge of the divider up and out Cleaning and Care To reduce the risk of electrical shock disconnect the appliance from the power supply by shutting off the power main tripping the circuit breaker or unplugging the power cord before maintenance Never use cleaning agents containing abrasive substances such as sand soda acids chlorides or chemical solvents Non abrasive cleaning agents are also unsuitable as they can cause matte areas to appear Do not allow water to get into the electronic unit or lights Do not allow water to get into the condensate channel and drain hole when cleaning Do not use a steam cleaner to clean this appliance Pressurized steam could penetrate electrical components and cause a short circuit Before cleaning m Turn off the appliance by pressing the main switch on the right side of the control panel m Unplug the power cord m Remove any food from the appliance and store it in a cool place m Take out any removable parts e g shelves trays drawers Cleaning the interior and accessories Use a mild solution of warm water and liquid dish soap Wash all accessories and drawers by hand Do not wash in a dishwasher m Clean the appliance as needed m Clean the condensate channel and drain hole frequently so that condensate can flow away easily Use a straw or similar item to clear the drain if necessary m After washing wipe down the interior and accessories with
30. ed a m Press the main switch on the right setting is changed or an alarm is side on the control panel to exit the triggered the temperature display will settings mode appear very bright If a button is not pressed within 2 minutes the electronics will return to x normal operation m Hold down the Super button for the freezer section for approx 5 seconds The Super indicator flashes and c flashes in the temperature display ems m Tap either of the temperature selection buttons until appears in the display m Press the Super button for the freezer section again h lights up in the display m Using the temperature selector buttons you can now choose a brightness level from 7 to 5 i dimmest setting 5 brightest setting m To save the setting press the Super button for the freezer section Alarm The appliance is equipped with an alarm system to ensure that the temperature does not rise unnoticed The alarm system is always operational it does not need to be turned on If the temperature becomes too warm the alarm sounds and the temperature display for the freezer section will flash The temperature set will determine when the alarm is triggered The alarm will sound and the display will flash if too much warm air flows into the appliance for example when food is being loaded re arranged or removed large amounts of food are being frozen at once Door alarm If one of the
31. ezer m Press the Super button for the refrigerator or freezer section as desired the indicator light will turn on N The appliance will now work at full power to lower the temperature in the refrigerator or freezer section Turning off the Super function for the refrigerator freezer The Super function automatically turns off after Refrigerator approx 6 hours Freezer approx 30 60 hours depending on the amount of food frozen The indicator light will go out and the appliance will run at normal power The Super function can be turned off early once a constant temperature of O F 18 C or colder has been reached in the freezer section or once the food and or drinks are sufficiently chilled in the refrigerator rN N m To turn the function off early press the Super button for the refrigerator or freezer as desired the indicator light will go out The appliance will now run at normal power Using the Super and DynaCool functions DynaCool d If the dynamic cooling function DynaCool is not switched on the natural circulation of air throughout the appliance can create different temperature zones See Using the refrigerator efficiently If you are placing a large amount of food in the refrigerator at one time the DynaCool function is recommended This will help to distribute the temperature evenly throughout the cavity so all food will be chilled to about the same temperature
32. ill provide the food already in the freezer with a protective boost of cold air 20 Placing food in the freezer Food to be frozen can be placed anywhere in the freezer section Large quantities of food should be placed directly on the glass cold plates to freeze the food quickly To do this remove the two top freezer drawers When taking these drawers out be sure not to block the ventilation slits in the back wall of the appliance They are important for trouble free operation of the appliance The lowest freezer drawer should not be removed Each drawer and each glass cold plate can hold a maximum of 55 Ibs 25 kg m Place the food flat in the bottom of the freezer drawers or on the glass cold plates so that it will freeze through to the core as quickly as possible m When placing items in the freezer make sure the packaging and containers are dry to keep them from sticking together when frozen When freezing make sure that already frozen food does not come into contact with fresh food being frozen this could cause the frozen food to defrost Using the freezer efficiently Freezing large items If you would like to freeze large items e g turkey or ham the glass cold plates between the drawers can be removed m Remove the top full width freezer drawer and carefully lift and slide out the glass cold plates Freezer calendar The calendar on the freezer drawers indicates the suggested length
33. imensions 22 5 5 6 445 364456 dhe es ooh EEG MC E P ier er 44 Adjusting the door hinges 0 0 0 eel 45 Installing the appliance iliis leise 49 Custom door panels iiisls eee 49 Installing the appliance as a room divider illii iile 49 Mounting the custom door panels l i 53 IMPORTANT SAFETY INSTRUCTIONS When using the appliance follow basic safety precautions including the following Read all instructions before installation and use to prevent accidents and machine damage This appliance is intended for residential use only Use only as described in this Operating manual Only use this appliance for its intended purpose The manufacturer cannot be held responsible for damages caused by improper use of this appliance This appliance complies with current safety requirements Improper use of the appliance can lead to personal injury and material damage Keep these operating instructions in a safe place and pass them on to any future user Electrical safety P Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond to prevent injury and machine damage Consult a qualified electrician if in doubt P Before installation or use check the machine for any visible damage A damaged machine is dangerous Contact the Miele Service Department P Do not use
34. ired safety of the appliance danger of overheating If any changes are needed to the household wiring or power supply this work must be performed by a qualified electrician 41 Installation Have the appliance installed by a qualified technician according to the enclosed installation instructions The manufacturer is not liable for damage to property due to an incorrect installation or water connection NWARNING This appliance is top heavy and must be secured to prevent it from tipping forward 42 Installation site The appliance should be installed in a dry well ventilated room Do not install the appliance outdoors in an environment with dripping water in rooms that are at risk of frost The installation location should not be exposed to direct sunlight or near a heat source such as an oven radiator etc The ambient temperature should not drop below 50 F 10 C or rise above 110 F 43 C otherwise malfunctions may occur If installation next to a heat source is unavoidable use a suitable insulating plate or observe the following minimum distances from the heat source 1 8 cm from an electric cooktop or oven 12 30 cm from a gas cooktop or oven Installation Ventilation The air at the rear wall of the appliance gets warm Therefore sufficient space must be provided around the appliance for ventilation A ventilation gap of at least 1 1
35. les service In the event of a fault which you cannot easily fix yourself please contact the Miele Technical Service Department at the address on the back of this booklet When contacting the Technical Service department please quote the model and serial number of your appliance given on the data plate inside the appliance MieleCare USA only MieleCare our Extended Service Contract program gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts Only genuine Miele parts installed by factory trained professionals can guarantee the safety reliability and longevity of your Miele appliance Please note that unless expressly approved in writing by the Miele Service department Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthorized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extended Service Contracts please contact your appliance dealer or visit us online at http store miele com 35 36 ser Installation instructions To prevent accidents and machine damage read these instructions
36. lly aligned using a level The cabinetry corners must be at 90 angles otherwise the custom door panels will not be flush with all 4 corners of the cabinetry 49 Installing the appliance Preparing the appliance m Push the appliance two thirds of the way into the installation niche Ensure that the power cord does not get caught m Slide the cover strip D nobs facing downwards into the holder The nobs will fit into the holes m Ensure that the power cord can be easily plugged in once the appliance is installed m For 16 mm cabinetry walls only Clip the spacers and onto the upper and lower hinges m Screw the provided fixing brackets into the pre arilled holes in the appliance door using a hex screw If the custom door panel is large screw on an additional pair of brackets 3 near the door handle 50 Installing the appliance m Open the appliance doors m Using the screws 8 M5 x 22 screw the plastic bracket to the door opening m Using the screws 40 loosely secure the fixing bracket 9 onto the appliance m f necessary shorten the sealing strip to match the height of the niche Remove the protective film m Starting at the bottom edge of the fixing bracket 9 stick the sealing strip on so that it is even with the front of the appliance on the side the door opens Installing the appliance
37. m Slightly loosen the screws 9 at the top middle and bottom m Slide the appliance doors outwards and unhinge them m Completely remove the screws 9 m oosely screw them into the top middle and bottom of the opposite side of the appliance m Pull the pins up and out of the hinges if necessary Adjusting the door hinges Removing the door closing device m With its exterior facing downwards place the appliance door on a stable surface m Leave the hinges open and remove the screw from the mounting Caution When uninstalled the door closing device will snap shut m Loosen the ball joint using an open ended wrench m Remove the door closing device together with the ball joint Do not remove the door closing device from the ball joint This will cause damage m Stand the appliance doors up individually and loosen the hinges on the front hinges remain open m Pull out the plugs from the top middle and bottom if the plugs are not in the doors the are supplied separately in the packaging m Remove the screws from all the hinges m Relocate each hinge diagonally in the opposite corner Do not close the hinges Risk of injury m To tighten the hinges use a power screwdriver the screws 2 are self tapping m Use the plugs to close the holes on the opposite side 47 Adjusting the door hinges Fastening the dampers m Hang the appliance doors on
38. o drop out of the ice cube maker and collect in the drawer Thereafter when the ice cube maker is turned off then on again it will take a maximum of 6 hours for ice cubes to be produced Do not use the ice cubes from the first three ice productions This will ensure that the water supply lines are flushed This applies for the very first use and whenever the appliance has been out of service for an extended period of time Making a large amount of ice cubes The amount of ice cubes produced depends on the temperature in the freezer section The lower the temperature the more ice cubes will be produced in a given period of time The ice cube production is interrupted automatically as soon as the ice cube drawer is full m To produce a larger amount of ice cubes exchange the ice cube drawer with the drawer on the right As soon as the drawer is closed the ice production will continue Turning off the ice cube maker m Press the On Off button on the ice cube maker until the indicator light goes out If the ice cube maker is turned off the ice cube drawer can be used to store food 23 Automatic defrost Refrigerator section The refrigerator defrosts automatically During normal operation condensate and frost can form on the rear wall of the refrigerator and drawers You do not need to remove this build up it will defrost and evaporate automatically with the heat generated by the appliance The con
39. ods such as fish meat poultry deli meats store bought meals dishes or baked goods containing eggs or cream fresh bread dough pastry dough cake batters dairy products Never store explosive materials in the appliance or products with flammable propellants e g spray cans Danger of explosion If storing high proof alcohol make sure it is tightly closed and stored upright Do not store cooking oil in the refrigerator door Traces of oil can cause stress cracks to occur in the plastic components in the door Do not allow food to touch the rear wall of the appliance it may freeze to the wall Using the freezer efficiently Maximum freezing capacity To ensure that food is frozen thoroughly the maximum freezing capacity should not be exceeded See the data plate Freezing capacity Ib kg 24 hrs Freezing food Fresh food should be frozen as quickly as possible This helps maintain the nutritional value vitamin content appearance and taste of the food Never refreeze partially or fully defrosted food Coook defrosted food as soon as possible it will lose its nutritional value and spoil if left for too long Do not refreeze defrosted food unless it has been cooked Before placing food in the freezer m When you are planning to freeze large amounts of food more than 4 1 Ibs 2 kg turn on the Super function for the freezer ahead of time see Super This w
40. or section freezer section DynaCool button dynamic cooling Alarm off button and indicator light Safety lock indicator light Guide to the Fridge Freezer combination D DynaCool fan dynamic cooling x CE m s 2 Hinged door shelf Eje Bottle rack aM IL Adjustable door shelves T 5 Interior lighting 8 Adjustable interior shelves aaa Condensate channel and drain hole i Il d Universal container T Fruit and vegetable drawers Divider amp Bottle shelf 62 Ice cube drawer with automatic ice cube maker 43 Freezer drawers with calendar depending on model Before use Before using for the first time The stainless steel frames of the shelves have a protective plastic coating to prevent scratching during transportation m Do not remove the plastic until the appliance has been installed m After removing the plastic treat the stainless steel with a stainless steel cleaner This will help protect the stainless steel and prevent resoiling m Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap To ensure proper functioning of the appliance let it stand for approx 30 mins to an hour before it is connected to the electrical supply Turning the appliance on With the main switch you can turn the appliance on
41. r damage caused by a faulty connection to the water supply P Do not operate any appliance with a damaged cord or plug or if the appliance has been damaged in any manner Contact Miele s Technical Service Department P This equipment is not designed for maritime use or for use in mobile installations such as recreational vehicles or aircraft P Do not install the fridge freezer in a room with too low an ambient temperature e g a garage as this may lead to the appliance switching off for longer periods so that it cannot maintain the required temperature P In refrigerators with an automatic ice maker avoid contact with the moving parts of the ejector mechanism Do not place fingers or hands on the automatic ice making mechanism while the appliance is plugged in P The ice cube maker is not suitable for connection to a hot water supply P Do not use water that is microbiologically or chemically unsafe or of unknown quality without adequate disinfection or other treatment P Defective parts must only be exchanged with original Miele spare parts Only then can the safety of the unit be guaranteed IMPORTANT SAFETY INSTRUCTIONS Use P Persons who lack physical sensory or mental abilities or experience with the machine should not use it without supervision or instruction by a responsible person P To reduce the risk of injury do not allow children to play in on or near the appliance P
42. r latch or lock unusable P Take off the doors P Leave the shelves and drawers in place so that children may not easily climb inside P Be careful not to damage any part of the pipework while awaiting disposal by puncturing the refrigerant channels in the evaporator bending any pipework scratching the surface coating Splashes of refrigerant can damage the eyes P Your old refrigerator may have a cooling system that used CFC s chlorofluorocarbons CFC s are believed to harm stratospheric ozone If you intentionally release this CFC refrigerant you can be subject to fines and imprisonment under provisions of environmental legislation Make sure the CFC refrigerant is removed and disposed of by a qualified technician The manufacturer cannot be held liable for damage caused by non compliance with these Important Safety instructions SAVE THESE INSTRUCTIONS Guide to the Fridge Freezer combination NO FROST C TE E CD On Off button for the refrigerator Main switch to turn the whole section appliance On Off 2 Temperature display for the Temperature display for the freezer refrigerator section section Temperature selection buttons for the s Temperature selection buttons for the refrigerator section freezer section warmer colder warmer colder Super button and indicator light for the Super button and indicator light for the refrigerat
43. ss phe Ee se dS obe dX E RS AT pU Gem SW Ap e E bas 22 olore EIC TP rcu EMT 22 Ice cube maker eee Rx ERR EE dee RE Ea su 23 Automatic defrost 0 0 0 0 00000 ees 24 Adjusting the interior fittings iles sellis 25 Moving the shelves eux ee oy asset er Erpa RR e REA Rea E Reis a 25 Split Shelp cce att RE qeu rev RP e RR E YU E acc dr pact 25 Fruit and vegetable drawers on rollers llli 25 Moving the adjustable door shelves iilii iilis 26 Universal container s ases scc er aco ex EROGO EY Kc SOUS e Ee Nu qo don E 26 MOWING the dVIQGE 4 esd ad bee Ra Romeo ore n o t De ade p abr cad 26 Contents Cleaning and Care 00 27 Cleaning the interior and accessories iil seien 27 Cleaning the ice cube tray liiis 28 Ventilation slits 0 e 28 Door Seal x astuces eleg xac n4 heed Whe eee Rds Merde ba AG RT RN On aed cs 29 Frequently asked questions iilii lilii leslie 30 After sales service liliis eee 35 Caring for the environment 0 000 0c ess 38 Plumbing 00 0 0 0 02 eee 39 Connecting the water supply s es saaana 39 Electrical connection 0 00 00 0 cc eee 41 Installation oes 3 gag Pood RE A EET EE E Ee E EST REPRISE Y 42 astallatlomltes cuu sedeo i cRE QUERER ORS e der ton Pee eee aa ee 42 Ventilation cte rose hed atur s d RU Reb RU Opes SUE mas pug ie eie a 43 Before installation cse 43 D
44. the m With its exterior facing downwards pre fitted POUSINS ANd DOSIUUUS doare inward again place the appliance door on a stable surface m Screw the ball joint 2 of the door closing device into the new fixing hole m Pull the door closing device apart m Tighten the screws at the top middle and hook the mounting onto the and bottom hinge m Snap on the covers and m Hold the door closing device in this m Replace the plugs position and screw the mounting to the hinge m insert the pins from above if necessary 48 Installing the appliance The following installation instructions are for a right hinged appliance door If you have converted the appliance door to be left hinged you will need to adapt the instructions accordingly Tools needed a Philips head screwdriver various sizes of Torx screwdrivers an open ended wrench Custom door panels The total weight of the panel s must not exceed the following otherwise the hinges may be damaged KFN 9755 iDE Upper door 31 Ibs 14 kg Lower door 27 lbs 12 kg Installing the appliance as a room divider If you wish to install the appliance as a room divider the back of the installation niche must be fitted with a panel so the back of the appliance is not exposed Aligning the installation niche Before installing the appliance the cabinetry must be carefu
45. uilt in Suitable 1 4 tubing or copper piping must be supplied for plumbing To ensure the best ice cube quality the maximum length of the tubing or copper pipe should not exceed 4 ft 11 1 5 m If too much water remains in the tubing the quality could be affected Connecting the water supply Before any installation or maintenance work is performed be sure the appliance is disconnected from the electrical supply Connection to the water supply should include a shut off valve with a 3 4 thread m Remove the cover cap from the solenoid valve m Install the compression fitting with the sealing ring on the solenoid valve m Attach the copper line to the compression fitting m Secure the copper line to the appliance using cable clips 9 39 Plumbing m Open the water supply slowly and check the water system for leaks m The appliance can now be connected to the electrical supply see Electrical connection Before using the appliance for the first time the water pipe should be purged of air by a qualified person m Slide the appliance into the installation niche Be sure not to kink the hose otherwise there is the risk of leaks and water damage After a maximum of 24 hours the first ice cubes will drop out of the ice cube maker and collect in the drawer 40 Electrical connection N Avoid the risk of electrical shock Plug into a grounded 3 prong outlet
46. within the following ranges Refrigerator 39 F 4 C to 48 F 9 C A temperature of 39 F 4 C is recommended in the refrigerator section Freezer 3 F 16 O to 15 26 C To freeze fresh food and store frozen food for an extended period of time a temperature of O F 18 C is suggested Partially or completely thawed food must never be refrozen The room temperature and the installation location can affect the time it takes for the appliance to get to the desired temperature If the room temperature is too high it may not be possible for the appliance to reach the lowest temperature Setting the temperature in the refrigerator and freezer sections The temperatures for the refrigerator and freezer sections can be set independently using the temperature selection buttons C e increases the temperature decreases the temperature button button The temperature being set will flash in the display When pressing the buttons the following information appears in the display When first pressed The last selected temperature flashes Each subsequent press of the button adjusts the temperature in increments of 1 F 1 C Holding down the button will move through the temperature range quickly Approx 5 seconds after releasing the button the current average temperature in the refrigerator or freezer section is automatically shown If the temperature is adjusted
Download Pdf Manuals
Related Search