MicroBoards Technology CWL-6200 Microcassette Recorder User Manual
Contents
1. Copying a Disc To copy a disc all you need to do is place a blank disc in one drive and the master disc in the other drive It does not matter which drive contains the master and which drive contains the blank Press the Disc Copy button on the CopyWriter Live front panel and the copy process will begin Please follow these steps to copy a disc 1 Place your master disc you wish copied into either of the two recorders The display for that drive will change to read the type of disc it is such as Data CD or Audio CD 2 Place your blank CD R or CD RW disc into the other recorder The display will change to CD RW or CD R depending on the type of blank disc you are using It will also display the total time available on that disc 3 Press the Disc Copy button on the front panel 4 The copy process will now start The display will show you the progress of the copy job NOTE If your master disc is larger than your blank disc you will see the message SPACE NOT ENOUGH If you see this message you will need to use a higher capacity blank disc CopyWriter Live Menu Options Pressing the Yes Setup button while no recording or playback is taking place will take you into the Setup menu Pressing the Yes Setup button at each displayed item will allow you to make changes to the specified setting Input This menu option allows you to switch the default input selection Note that you can change the input selection at any time except during re2. Power Supply AC 90V 264V Dimensions 11 38 x 16 69 x 4 56 4 38 without feet Weight 12 3 Ibs 14
3. immediately You can have up to 99 tracks on a single CD Pressing Disc Change during the recording process will switch the recording from the original drive to the other drive provided that it contains a blank disc The disc in the original drive will be closed automatically Press the Pause button to pause the recording process Press Record to begin recording again to a new track Note that you cannot start the next track until the last track information has been completed during which time the display will read Close Track Recording can begin again once that message clears While paused the input selection can be changed Press and hold the STOP button for 2 seconds while recording live to finalize the disc The disc MUST be finalized in order to play the CD in any other system If the Pause button was used to end the last recorded track the disc has not been finalized and you will need to do so from the CD Tools menu before the disc will be playable see pg 11 CD Tools Close Disc Playing a Disc 1 2 Confirm you have your Audio Out connected to a playback device Audio Receiver etc or have headphones connected to the front panel Place the disc you wish to play back into either of the CD R W drives Press the Play button on the front panel Use the playback buttons on the front panel to control playback If using headphones adjust the volume using the knob next to the headphone jack Microboards CopyWriter Live
4. the flexibility of cassette tapes with the quality and longevity of CDs in one low cost easy to use unit You can record from practically any audio source including live feed from a microphone a cassette deck a mixer and many others Make a high quality CD on the first try every time You can even span from disc to disc to record non stop for hours on end e Audio Audio CD playback is possible on virtually any player e Audio Track Creation Just by pressing the RECORD button you can create your next track on your audio CD e Audio Gap Size You can select how long the silence will be in between tracks This value ranges from 1 75 of a second to 2 seconds e Ease of Use With an easily navigable display and intuitive interface the CopyWriter Live requires very little training to use effectively e Duplication Function The CopyWriter Live works as a duplicator too Simply drop your master in one drive and a blank in the other and hit Disc Copy e Multiple Sources The CopyWriter Live features RCA and XLR inputs so virtually any audio source live or pre recorded can be burned to a CD e Spanning Capable Recording more than 80 minutes is not a problem The Copy Writer Live will continuously record by utilizing both its recorders when one disc reaches capacity it starts recording on the other What s Included The CopyWriter Live system comes with the following items CopyWriter Live system AC Power Cord RCA cabl
5. CopyWriter Live CWL 6200 Audio Disc Recorder Instruction Manual Microboards Technology LLC 8150 Mallory Court Chanhassen MN 55317 Version 2 1 www microboards com Microboards CopyWriter Live Microboards CopyWriter Live Table of Contents IntrodUctlOn 2 iiereiececo reco ote ota tente sess onera aora ee acaso d ep a tense aoaeeoo sso essee seo ceee tronet e E What s Included 5 Controls sesesdsssd sscsadecedesccdseseleccscedsccdesseseccccsdsccdsocesacescecdsededsessteceasesstsecsobescsdsscdessessteset etetsese O LG TT U IDIOT Back Panel XLR RCA Output RCA Input 1 and Power eene 7 Front Panel MIC Input 2 and Headph ner ir a ie eae d eda 7 Rack Mount Install aten sanken System Operation anreisen ac III W D E PCR TRAE Recording Procedure for Audio CD urn see a 9 Playing a DII nr D Copying a DISC CopyWriter Live Menu Options sssesssnseossnsesnonnusnonnunsnnsnssnnnsesnnssssnnsnssnsnussnsnusenenesene L0 Input a cec ioter ce oci ea Meuse eec Seal ra man Secr aad 10 System U pe oc oni o p tee tm teu ase lp mend deat cunt ter eu one akan es 12 Auto Track Ind x are aaa et 13 CVAD SIDS SG dec tati ale a E deer e E us das 13 Setup PR T 13 Troubleshooting see ED haces cnc Vk wanes ieee udo LO Contact Information Technical Specifications eee ioo ee enn br ero cconccedsenessdscteteeccsncen
6. Playback of this disc is only possible on the CopyWriter Live system If you press Pause while recording a project and then decide you do not want to record any additional information to that CD you can close the disc by selecting Close Disc in the CD Tools Menu Press the No button until you reach the drive you wish to close either the left or right drive Press Yes Setup to start the process The message Closing Disc will flash until the disc is closed After the closing of the disc is complete press the Yes Setup screen to return back to the CD Tools menu Quick Erase Full Erase The CW Live can erase CD RW media You have the choice of doing a quick erase or a full erase Just place the CD RW disc in either or both drives and press the Yes Setup button at the left or right drive The message Erasing CD will flash on the display until the process is complete Once the erase is completed press the Yes Setup button to go back to the CD Tools menu Track Extraction This menu option allows you to extract tracks from one master and burn them to a blank disc To use this feature follow the directions below 1 Press Yes Setup at the Track Extraction menu selection in the Setup menu to begin 2 The display will read Extraction OK Press Yes Setup and the drives will eject Place the master disc in one drive and a blank in the other and close the drive trays The master will run through a track analysis It does not matter in which drive
7. The center caption indicates the input method currently selected During duplication the display will show the audio levels of the disc currently being burned as horizontal lines above the input with the left channel above the right An 08 16 lt INPI DISC will appear on the right if levels are too high RECO2 Creating a Disc Creating an Audio CD is easy with the CopyWriter Live The first step is to make sure you have your audio source connected see page 7 for more on the available connections Once you have completed your connections select the appropriate input source on the CopyWriter Live The input level can be monitored by reading the meter displayed on the screen The following is a step by step description on how to create a disc e Connect your audio source to the CopyWriter Live e Place a blank disc in either of the two CD R W recorders If your recording will be longer than one CD place blank media in both recorders Wait for the media to spin up in the recorder The ICON on the display will change to CD R W or CD R depending on the type of blank disc you are using It will also list the total recording time available on that disc e Confirm your Input Selection is correct Input 1 Input 2 MIC or XLR It is important to make sure you have selected the correct input e The MIC input selection is used to create Audio CD s directly from a connected microphone only Microboards CopyWriter Live Recording Proc
8. cording by pressing the Input button but this will not change the selection that first appears when the CopyWriter Live is turned on The CopyWriter Live default for input selection is Input 1 Choices for the input selection are INPUT 1 INPUT 2 XLR and MIC Volume You can control the input volume for each input selection of the CopyWriter Live system A different volume level can be saved for each input selection Press the Yes Setup button to change the volume for the displayed input selection or No to move to the next selection After pressing Yes Setup use the Vol Up and Vol Down buttons to change the volume setting for the input selection Press Yes Setup again to save the new volume level and return to Volume in the Setup menu Pressing No will discard the changes The input volume can also be controlled during recording by using the Vol Up and Vol Down buttons 10 Microboards CopyWriter Live CD Tools The CD Tools menu item allows you to close an open Audio CD It also allows you to erase a CD RW disc Press Yes Setup when you have selected the CD Tools entry on the Setup Menu There are 3 options under the CD Tools menu Close Disc In order for a recorded disc to play back correctly in other players the disc must be closed If you press Stop to stop your recoding then the disc is closed and can be played on other playback devices If you press Pause while recording a disc recording will stop but the disc is not closed
9. dphones Plug a microphone into the 1 inch input port on the front of the CopyWriter Live Left Right RCA Input 2 is available as an input source on the front panel The Headphone jack can be used to monitor the audio either during recording or playback It is recommended that you set the headphone volume at a comfortable level before changing the input volumes during recording Headphone Jack Left Right RCA Input 2 Microboards CopyWriter Live Rack Mount Installation To mount the rack mount brackets on your CopyWriter Live system please follow these steps 1 If you system is turned on turn off power and unplug the power cord from the back of the system 2 Turn the system over and remove the four feet from the bottom of the CopyWriter Live 3 With the system upside down mount the brackets in place The L shape of each bracket will wrap around the side and bottom of the CopyWriter Live 4 Secure the brackets on the bottom with two screws for each bracket 5 Flip the CopyWriter Live system over and secure the side of the bracket with a screw in the upper corner on each side 6 Each bracket should now have three screws installed two on the bottom and one on the side 7 The CopyWriter Live is now ready to be placed in your rack System Operation After powering on the system the following screen is NO NO displayed DISC lt INPI DISC The left and right captions indicate the contents of the left and right drives
10. dsseteuvdesvgesecssnevebeccvevensepwes 14 Advanced Features u natal sd di DE eed d 14 DU LIC ALLO Suis re este due ds 14 SuUpporled Formats LES 14 Mechanical 7 Eleetrical uucun ana an 14 Microboards CopyWriter Live Important Safety Instructions e Read the User s Manual completely e Observe all warnings e Do not connect or disconnect the power cord when your hands are wet e Keep unit and power cord aware from any heat source such as radiators stoves or heat registers e Do not attempt to repair the AC cord in any way e Do not modify the AC plug The grounding plug is designed for your safety e Do not remove or otherwise modify the power cord for any reason e Protect the power cord from being walked on or pinched e Keep away from water Do not place this unit near water including flower vases tubs sinks etc e Clean this unit only with a dry cloth e Unplug this unit during lightning storms or when unused for long periods of time e Do not stack heavy objects on top of this unit Place the player in a horizontal position only e Avoid placing the player in direct sunlight areas of excessive dust high temperature or vibration e Use only attachments and accessories specified by the manufacturer e Do not insert any foreign object into the unit or on to the drive trays e Refer all servicing to qualified service personnel Microboards CopyWriter Live Introduction The CopyWriter Live combines
11. ed tracks in order on the new disc first followed by the odd numbered tracks in order You would need to select the even numbered tracks from the master the first pass then burn to the blank disc When asked for the next master press Yes Setup but keep the master in the tray Select the odd numbered tracks burn the tracks then answer No at the next master prompt to close the disc Beep This setting allows you to turn on or off the button beep Use the Vol Up or Vol Down button to turn the beep on or off Press Yes Setup when done System Info System Info allows you to view the current firmware version installed on the Copy Writer Live Press Yes Setup at the System Info menu selection in the Setup menu to review the Firmware Version and Hardware Version Press No to review the drive make model and firmware Press No to have the option of returning to the Setup menu System Update The CopyWriter Live system can be updated with a CD If there are changes in the firmware such as improved features bug fixes etc the system can be updated using the System Update feature In the Setup menu press the No button until System Update is selected Press the Yes Setup button and the left drive will eject prompting you to place the firmware disc in the drive with the message Insert Program Disc Place the disc in the drive and close the tray The new firmware will be read by the system and then copied into the CopyWriter Live After t
12. edure for Audio CD 1 If you are creating an Audio CD with multiple tracks set your Gap value to determine how long the silence will be between tracks See page 12 fora description of how to set the Gap value Determine the input level of your recording This can be done by playing a sample of your input audio The input meter will show the level of the audio If your audio source volume is too low the meter may show little or no activity In that case you should increase your input volume by pressing the Vol Up button If your audio source volume is too high the meter will indicate this by displaying an asterisk as the right bar symbol and the input volume should be reduced by pressing the Vol Down button Once you have your input volume set for your particular source you are ready to record Start playing your source If you are recording a live session wait for the program to begin Press Record on the CopyWriter Live This will start the recording If your recording is longer than CD it will span to the second disc The second CD will start to record up to 30 seconds before the first CD ends so this amount of time will be recorded on both discs Once the second disc is full it will span back to the first CD assuming you have a blank disc in the drive Recording volume from the input can be changed during recording by using the Vol Up and Vol Down buttons Press the Record button to start creating your next track
13. es Users Manual CD R media e Rack Mount brackets and screws If any of these items are missing please contact Microboards Technical Support at 952 556 1639 or by email at support microboards com Microboards CopyWriter Live Controls 1 Left CD Recorder Drive 2 Eject for Left CD Recorder Drive 3 Right CD Recorder Drive 4 Eject for Right CD Recorder drive 5 Power Button 6 Disc Change Button 7 Yes Setup Button 8 No Button 9 Volume Up 10 Volume Down 11 Input Button 12 Play Mode Button 13 Display Screen 14 Display Button 15 Previous Button 16 Next Button Playback Controls 17 Play Pause Button 18 Stop Button 19 Record Button 20 Disc Copy button 21 Headphone Volume Microboards CopyWriter Live Connections Important Note Make sure the power is turned off to the CopyWriter Live system when connecting or disconnecting any cables Back Panel XLR RCA Output RCA Input 1 and Power Input connections can be made to the XLR connection on the back or to the RCA Input 1 connection The power connection is also on the back Audio monitoring can be done either from the Headphone jack on the front of the CopyWriter Live or from the Output RCA jacks on the back RCA Input to Tape or CD Player Left amp Right XLR Connection to External Source Power Connection 100 Left Right RCA Output 240V AC Auto Detect to Audio Receiver Front Panel MIC Input 2 and Hea
14. he firmware is updated you will need to shut the CopyWriter Live off and restart it Once the system boots back up it is ready to use with the new firmware installed Input Volume and Gap Sizes will be returned to the default values 12 Microboards CopyWriter Live Auto Track Index This feature allows you to have the Copywriter Live automatically create tracks based on the time period you select Press Yes Setup button when the Setup menu display reads AUTO Trk INDEX The first selection is No which will not create tracks automatically The choices which will allow auto tracking are 3 minutes 5 minutes 7 minutes and 70 minutes Press No until the correct interval appears then press Yes Setup to select that interval You can still manually index tracks even with the Auto Track Index feature turned on by pressing the Record button The next auto track will be the length you have specified in the Auto Track Index Note that the gap between tracks will be set based on the Gap Size setting see below Gap Size The length of silence in between audio tracks can be set by changing the Gap Size value The Gap Size value ranges from 001 to 150 At 150 the gap is 2 seconds At 001 the gap is approximately 1 75 of a second The default value is 001 Use the Vol Up and Vol Down buttons to change the Gap size Setup Exit Press Yes Setup to leave the Setup menu or No to cycle through the options again Troubleshooting Playback is n
15. ot appearing on the screen Confirm the RCA connections are correct No Audio playback Confirm the RCA connections are correct Check the playback volume and make sure it is not too low Disc will not play back on other player Confirm the recorded disc is Closed Check compatibility of player Supports CD Recordable media Playback volume too high or too low on burned CD Check input volume Default settings for Input 1 and Input 2 are 22 Default settings for MIC and XLR are 25 Check this number in the setup menu and adjust accordingly 13 Microboards CopyWriter Live Contact Information For technical questions or support issues please contact Microboards Technology technical support at PH 952 556 1639 FAX 952 556 1628 by email at support microboards com or on the web at http www microboards com Technical Specifications Advanced Features Standalone CD Duplication with automatic format detection Record and Pause to create multiple tracks for playback Black set top configuration Play back Audio discs on PC or Mac Specifications LCD system display 2 pairs of RCA inputs 1 rear 1 front 1 pair of XLR inputs rear 1 pair of RCA outputs rear 1 inch Microphone input front 1 inch Headphone output front Supported Formats CD ROM Mode 1 amp 2 CD DA Red Book Audio CD ROM XA Mixed Mode Multisession HFS CD Bridge CD Extra Mechanical Electrical Signal to Noise Ratio 90dB
16. the master is placed 3 After the master is analyzed the display will read EXTRACT THE TRK followed by TRACK 01 XX where XX is the number of tracks on the master Press Yes Setup to select the track or No to not select the track 4 Repeat step 3 until all tracks on the master have been offered for extraction 5 After the last track on the master the display will read End Extraction Press Yes Setup to begin burning the selected tracks to the blank disc Press No if you wish to change your selections you will run through steps 3 5 again 11 Microboards CopyWriter Live 6 After the selected tracks have been burned the display will read Next Master Press Yes Setup and the master drive will be ejected to allow you to insert a new master Close the tray and repeat steps 3 5 for the new master 7 When you have burned the last track to the disc answer No to the Next Master query The disc will then be closed automatically ejecting when complete You cannot put more tracks on the disc than the disc will hold If the capacity of the disc will be exceeded by selecting a track you will not be able to select that track Note If you wish to rearrange the tracks on a single master you can do so by selecting tracks off the same master multiple times You will need to plan the order of the tracks as you cannot reverse the orders of tracks during a single master track extraction sequence For example you wish to place all the even number
Download Pdf Manuals
Related Search