Home

Mercedes-Benz S 500 Automobile User Manual

1. Mercedes Benz Operator s Manual S 500 S 600 Product information Kindly observe the following in your own best interest We recommend using Mercedes Benz original parts as well as conversion parts and accessories explicitly approved by us for your vehicle model We have tested these parts to determine their reliability safety and their special suitability for Mercedes Benz vehicles We are unable to make an assessment for other products and therefore cannot be held responsible for them even if in individual cases an official approval or authorization by governmental or other agencies should exist Use of such parts and accessories could adversely affect the safety performance or reliability of your vehicle Please do not use them Mercedes Benz original parts as well as conversion parts and accessories approved by us are available at your authorized Mercedes Benz Center where you will receive comprehensive information also on permissible technical modifications and where proper installation will be performed Our company and staff congratulate you on the purchase of your new Mercedes Benz Your selection of our product is a demonstration of your trust in our company name Further it exemplifies your desire to own an automobile that will be as easy as possible to operate and provide years of service Your Mercedes Benz represents the efforts of many skilled engineers and craftsmen To ensure your pleasure of ownership and for y
2. If ice has formed on the road tire traction will be substantially reduced Under such weather conditions drive steer and brake with extreme caution We recommend M S radial ply tires for the winter season for all four wheels to insure normal balanced handling characteristics On packed snow they can reduce your stopping distance as com pared with summer tires Stopping distance however is still considerably greater than when the road is wet or dry Tire Speed Rating Your vehicle is factory equipped with an H rated tire which has a speed rating of 130 mph 210 km h An electronic speed limiter prevents your vehicle from exceeding the speed resting Notwithstanding tire speed rating local speed limits should be obeyed and prudent driving speeds appropriate to prevailing conditions should be employed Warning Never operate a vehicle at speeds greater than the maximum speed rating of the tires with which it is equipped Exceeding the maximum speed for which tires are rated can lead to sudden tire failure causing loss of vehicle control and resulting in personal injury and possible death Parking Warning To reduce the risk of personal injury as a result of vehicle movement before turning off the engine and leaving the vehicle always 1 Keep right foot on brake pedal 2 Firmly depress parking brake pedal Move the selector lever to position P Slowly release brake pedal Turn front
3. Manual Retraction of Trunk Lid Handle The trunk lid handle can be retracted manually should a malfunction occur with the automatic system Push sliding switch down 1 and to the right 2 118 Fa2 0049 813 Replacing Wiper Blades For safety reasons remove key from steering lock before replacing a wiper blade otherwise the motor can suddenly turn on and cause injury Windshield Wiper Blades Removal Pull wiper blade arms upward from the rest position to their stop Replace wiper blades one at a time to prevent the wiper arms from sliding back to the rest position Notes Do not open engine hood with wiper arms folded forward Do not allow wiper arms to contact the windshield glass without wiper blades inserted The glass may be scratched or broken Make certain that the wiper blade is properly installed An improperly installed blade may cause windshield damage Fold wiper arm forward Press safety tab down 1 push wiper blade downward 2 and remove Installation driver s side Press safety tab of new wiper blade down Insert wiper blade between the tabs 3 on the wiper arm and slide into end of wiper arm Then press safety tab upward until it locks in place Installation passenger side Fold wiper arm forward and slide wiper blade into end of wiper arm until safety tab locks in place 119 Headlamp Wiper Blade Removal Fold wiper arm forward Push pin 1 and remov
4. SHES PIDH B13 Storage Compartments in the Door 6 Button for door pocket To open Press button Caution Keep compartment lids closed This will prevent stored objects from being thrown about and injuring vehicle occupants during an accident 64 PRT 019 19 in center console front Ashtrays By touching the top of the cover lightly the ashtray opens automatically Prior to removing the ashtray insert move gear selector lever to position N Warning With the gear selector lever in position N turn off the engine and set The parking brake Otherwise the vehicle might move unintentionally in rear doors To remove ashtray from center console Push sliding knob 1 toward the right to eject the insert To remove ashtray from rear door Hold left and right side of insert and pull up To install ashtray Install insert into ashtray frame and push down to engage Pat dhi20 674 Lighter Turn key in steering lock to position lor 2 Push in lighter 1 it will pop out automatically when hot Warning Never touch the heating element or sides of the lighter hold at knob only 65 p4 PA2 0089 613A Sliding Roof with Rear Pop Up Feature to slide roof open to slide roof closed to raise roof at rear to lower roof at rear hWN TTP al pre cooeata Turn key in steering lock to position 1 or 2 with either front door open the sliding pop up roof can be operated with
5. Always replace wheel bolts that are damaged or rusted Never apply oil or grease to wheel bolt threads Damaged wheel hub threads should be repaired immediately 101 11 12 wo Clean contact surfaces of wheel and wheel hub Install spare wheel on wheel hub Insert wheel bolts and tighten them slightly To avoid paint damage place wheel flat against hub and hold it there while installing first wheel bolt Unscrew the alignment bolt to install the last wheel bolt Lower car Remove jack and insert jack tube cover 13 Unfold wrench and tighten the five bolts evenly following the sequence illustrated above until all bolts are tight Observe a tightening torque of 110 ft lb 150 Nm 14 Correct tire pressure Important When installing new wheels the mounting bolts must be retightened after approx 60 300 miles 100 to 500 km Before storing the jack the jack arm must be lowered almost to the base of the jack Warning Incorrect mounting bolts or improperly tightened mounting bolts can cause the wheel to come off This could cause an accident Be sure to use the correct mounting bolts 102 Tire Inflation Pressure A table see fuel filler flap lists the tire inflation pressures specified for summer and winter tires as well as for the varying operating conditions Important Tire pressure changes by approx 1 5 psi 0 1 bar per 18 F 10 C of air temperature change Ke
6. MAX maximun air flow 9 Economy The function of this setting corresponds to the automatic mode However because the air conditioning compressor will not engage fuel savings it is not possible to air condition in this setting 11 Off EE The fresh air supply to the car interior is shut off While driving use this setting only temporarily otherwise the windshield could fog up Important This vehicle is equipped with an air conditioner system that uses HFC 134a ozone friendly hydro fluorocarbon as a refrigerant Repairs should always be performed by a qualified technician and refrigerant should be collected in a recovery system for recycling 26 Active Charcoal Filter Rear Passenger Compartment Adjustable Air Outlet 1 Switch on Vehicles without rear passenger 2 Switch off compartment climate control Slide switch 1 up to open outlet for fresh cooled air only An active charcoal filter markedly reduces bad odors and removes pollutants from the air entering the passenger compartment When pressing button or HE the filter is automatically switched off Note The active charcoal filter should be switched off when windows fog up on the inside or if the passenger compartment needs to be quickly heated up or cooled down 27 Car Keys Included with your vehicle are e 2 Master keys with infrared remote control e 1 Master key e 1 Valet key e Flat key Infrared Remote
7. it can only be continued by first turning the key to the unlocked position 3 and then again to the locking position 1 and hold 34 Power Closing Assist for Doors and Trunk Lid The doors and trunk lid close automatically if e doors are pushed against the lock e trunk lid is lowered against the lock It is not necessary to slam doors or trunk lid closed a pneumatic power assisted mechanism will latch doors and trunk lid quietly and automatically once the lid or door has been brought to a close When the pneumatic power assisted mechanism has stopped doors and or trunk can be reopened Note If the trunk lid does not close refer to Trunk Lid Manual Closing in Index Warning To prevent possible personal injury always keep hands and fingers away from the door or trunk opening when closing a door or the trunk lid Be especially careful when small children are around The pneumatic power closing assist mechanism cannot be interrupted once it has been engaged To prevent personal injury never activate the closing assist mechanism by tampering with the door or trunk lid latch 35 1 P76 0038 614 Indicator lamp in switch located in center console Anti Theft Alarm System The anti theft alarm is automatically armed or disarmed with any of your vehicle s keys or infrared remote control by locking or unlocking either front door or the trunk A blinking lamp 1 indicates that the alarm i
8. periodically 115 Testing Infrared Remote Control Checking Batteries If the transmit button 1 is pressed longer than 1 second the battery indicator lamp in the transmitter eye 2 briefly illuminates indicating that the batteries are in order Change batteries if the indicator lamp does not come on Changing Batteries Slide release 3 laterally and pull off battery cover 4 Change batteries When inserting new batteries make sure they are correctly installed Slide battery cover onto housing until locked in place Important Batteries contain materials that can harm the environment if disposed of improperly Recycling of batteries is the preferred method of disposal For disposal please follow manu facturer s recommendation on battery package Replacement battery Silver oxide type 76 or Mercury oxide type 675 P76 0004 613 Synchronizing System The system may have to be re synchronized if the transmitter is without voltage for several minutes To synchronize system aim transmitter 2 at a receiver 5 and briefly press transmit button 1 Within approx 30 seconds lock or unlock the car at a door or the trunk using the master key The infrared remote control should once again be operational 116 Front Head Restraints Removal Push button 1 up to bring the head restraint to its highest position P91 0029 649 Depress release button 2 beneath the seat
9. Agent Before the start of the winter season or once a year in the hot southern regions you should have the anticorrosion antifreeze concentration checked The coolant is also regularly checked each time you bring your vehicle to your authorized Mercedes Benz dealer for maintenance service Anticorrosion antifreeze quantity Model Approx freeze protection 35 F 49 F 37 C 45 C S 500 8 2 US qt 9 0 US qt 7 75 1 8 50 1 S 600 10 6US qt 11 6 US qt 10 00 1 11 00 1 134 Consumer Information This has been prepared as required of all manufacturers of passenger cars under Title 49 Code of U S Federal Regulations Part 575 pursuant to the National Traffic and Motor Vehicle Safety Act of 1966 Uniform Tire Quality Grading Refer to the tire sidewall for the specific tire grades for the tires with which this vehicle is equipped All passenger car tires must conform to federal safety requirements in addition to these grades Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and one half 1 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service
10. Check regularly and before a long trip 143 Child restraint 43 48 49 52 54 Cleaning and care of the vehicle 113 Clock setting 69 Combination switch 56 Consumer information 135 Coolant level low Adding coolant 93 Low engine coolant level warning lamp 81 Coolant level checking 93 Coolant temperature gauge 80 81 Coolants 134 Cruise control 76 Drinking and driving 72 Driving instructions 16 Driving off 72 Emergency tensioning retractor ETR 49 Emission control 88 Engine malfunction CHECK ENGINE malfunction indicator lamp 88 Engine oil consumption 79 Engine oil level low Low engine oil level warning lamp 94 Engine oil level checking 94 Engine oil pressure gauge 15 78 Engine oils 130 132 Engine overheating 80 Engine speed limit Overrevving 75 Exterior lamp failure indicator lamp 82 Exterior lamp switch 58 139 First aid kit 96 Fuel Fuel requirements 133 Gasoline additives 133 Premium unleaded gasoline 14 131 132 Fuel consumption gauge 79 Fuel filler flap manual release 121 Fuel reserve warning lamp 80 Fuses 108 Head restraints front 37 Head restraints rear 42 Head restraints removal 117 Headlights 58 Heated seats 41 Hood 92 Identification plates 124 Indicator lamp symbols 13 Instrument cluster 12 Interior lighting 63 Jump starting 110 Keys vehicle 28 Lamps exterior Fog lamps 58 Headlamp adjusting 107 Headlamps 58 82 105 High mounted stop lamp 109 License plate la
11. F 20 C we recommend that an engine block heater be installed Your authorized Mercedes Benz dealer will advise you on this subject 15 Driving Instructions Power Assistance Warning When the engine is not running the brake and steering systems are without power assistance Under these circumstances a much greater effort is necessary to stop or steer the vehicle Brakes Caution When driving down long and steep grades relieve the load on the brakes by shifting into 3 2 or B This helps prevent overheating of the brakes and reduces brake pad wear Do not exceed engine speed limits Refer to Technical Data for downshift points After hard braking it is advisable to drive on for some time rather than immediately parking so the air stream will cool down the brakes faster Warning After driving in heavy rain for some time without applying the brakes or through water deep enough to wet brake components the first braking action may be somewhat reduced and increased pedal pressure may be necessary Be sure to maintain a safe distance from vehicles in front The condition of the parking brake system is checked each time the car is in the shop for the required maintenance Between maintenance checks it is a good practice to apply the parking brake once or twice while driving at approximately 30 mph 50 km h ona dry straight road Apply parking brake lightly while pulling the release handle out until
12. For the removal of the Rear Seat Cushion see Index 43 Adjustable Steering Wheel Turn key in steering lock to position 1 or 2 with the driver s or front passenger s door open the steering wheel can also be operated with the key removed or in steering lock position 0 To lengthen or shorten the steering column push in or pull out switch 1 To raise or lower steering wheel push switch 1 up or down Note The steering wheel position can be stored in memory together with the seat head restraint exterior and inside rear view mirror positions see Index Warning Do not adjust the steering wheel while driving Adjusting the steering wheel while driving could cause the driver to lose control of the vehicle 44 Seat Belts and Supplemental Restraint System SRS Your vehicle is equipped with seat belts for all seats emergency tensioning retractors for the front seats as well as airbags and knee bolsters for driver and front passenger Seat Belts Important Laws in most states and all Canadian provinces require seat belt use All states and provinces require use of child restraints that comply with U S Federal Motor Vehicle Safety Standard 213 and Canadian Motor Vehicle Safety Standard 213 1 We strongly recommend their use Warning Never ride in a moving vehicle with the seat back reclined Sitting in an excessively reclined position can be dangerous You could slide under the seat belt
13. Rapid heating mode Both indicator lamps in the switch light up After approximately 5 minutes in the rapid heating mode the heater automatically switches to normal operation and only one indicator lamp will stay on Turning off heater If one indicator lamp is on press upper half of switch If both indicator lamps are on press lower half of switch If left on the heater automatically turns off after approximately 30 minutes of operation Note When in operation the seat heater consumes a large amount of power It is advisable not to use the seat heater longer than necessary The seat heaters may automatically switch off if too many power consumers are switched on at the same time or if the battery charge is low When this occurs the indicator lamp in the switch will blink both indicator lamps blink during rapid seat heating The seat heaters will switch on again automatically as soon as sufficient voltage is available If the blinking of the indicator lamps is distracting to you the seat heaters can be switched off 41 Switches in center consoles Power Head Restraints Rear Turn key in steering lock to position 1 or 2 with the driver s or passenger s door open the power head restraints can also be operated with the key removed or in steering lock position 0 Activate switch 1 Place head restraint upright 2 Fold head restraint backward Po7 O0s0 013 Switch in front center
14. a slight drag on the wheels is felt Keep applying the brake for about 10 seconds while pulling the release handle out before releasing the parking brake completely This practice will keep the parking brake at maximum efficiency Warning The stop lamps will not come on when applying the parking brake only Perform the procedure in the previous paragraph only when the road is clear of other traffic Resting your foot on the brake pedal will cause excessive and premature wear of the brake pads It can also result in the brakes overheating thereby significantly reducing their effectiveness It may not be possible to stop the car in sufficient time to avoid an accident All checks and maintenance work on the brake system should be carried out by an authorized Mercedes Benz dealer 16 If the parking brake is released and the brake warning lamp in the instrument cluster stays on the brake fluid level in the reservoir is too low Brake pad wear or a leak in the system may be the reason for low brake fluid in the reservoir Have the brake system inspected at an authorized Mercedes Benz dealer immediately Install only brake pads and brake fluid recommended by Mercedes Benz Warning If other than recommended brake pads are installed the braking properties of the vehicle can be degraded to an extent that safe braking is substantially impaired Tires Tread wear indicators TWI are required by law These
15. by using the switch If the seat belt is not buckled within 30 seconds the seat belt extender will return to its rest position This is also the case if the key is turned to steering lock position 1 or if a door is opened Warning The seat belt extender must be in its rest position for the seat belt to provide proper protection If the electrical system fails forcibly push the extender back to its rest position If the seat belt extender cannot be brought to its rest position the seat belt cannot provide proper protection in case of an accident In this case have the system checked at your authorized Mercedes Benz dealer 46 PBG 0026 Bid 1 Latch plate 2 Buckle 3 Release button Fastening of Seat Belts Push latch plate 1 into buckle 2 until it clicks The lap belt should be positioned as low as possible on your hips and not across the abdomen Tighten the lap portion to a snug fit by pulling shoulder portion up Tighten to a snug fit by feeding belt toward retractor fj pas o025 813 Adjust seat belt so that shoulder portion is located as close as possible to the middle of your shoulder Do not twist the belt A twisted seat belt may cause injury The shoulder portion of the seat belt must be pulled snug and checked for snugness immediately after engaging it The height setting for the shoulder portion of the front seat belts are automatically adjusted by the fore aft movement of t
16. in a collision If you slide under it the belt would apply force at the abdomen or neck That could cause serious or even fatal injuries The seat back and seat belts provide the best restraint when the wearer is in an upright position and belts are properly positioned on the body Seat Belt Warning System With the key in steering lock position 2 an audible warning sounds for a short time if the driver s seat belt is not fastened Warning Failure to wear and properly fasten and position your seat belt greatly increases your risk of injuries and their likely severity in an accident You and your passengers should always wear seat belts Warning If you are ever in an accident your injuries can be considerably more severe without your seat belt properly buckled Without your seat belt buckled you can hit the interior of the vehicle or be ejected from it You can be seriously injured or killed In the same crash the possibility for injury or death is lessened with your seat belt buckled 45 Seat Belt Extender When the respective door is closed and the key is in steering lock position or 2 the seat belt extender brings the belt forward within easy reach of the occupant The seat belt extender also brings the belt forward if the seat is not occupied Ups Ott j 141 4 Switch on center console With the doors closed and seat belt not buckled the seat belt extender can also be brought forward
17. indicators are located in six places on the tread circumference and become visible at a depth of approximately 16 in 1 5 mm at which point the tire is considered worn and should be replaced The tread wear indicator appears as a solid band across the tread Warning Do not allow your tires to wear down too far With less than in 1 5 mm of tread the adhesion properties on a wet road are sharply reduced Depending upon the weather and or road surface conditions the tire traction varies widely Specified tire pressures must be maintained This applies particularly if the tires are subjected to high loads e g high speeds heavy loads high ambient temperatures Warning Do not drive with a flat tire A flat tire affects the ability to steer or brake the vehicle You may lose control of the car Continued driving with a flat tire or driving at high speed with a flat tire will cause excessive heat build up and possibly a fire 17 Aquaplaning Depending on the depth of the water layer on the road aquaplaning may occur even at low speeds and with new tires Reduce vehicle speed avoid track grooves in the road and apply brakes cautiously in the rain Tire Traction The safe speed on a wet snow covered or icy road is always lower than on a dry road You should pay particular attention to the condition of the road whenever the outside temperatures are close to the freezing point Warning
18. of batteries is the preferred method of disposal Many states require sellers of batteries to accept old batteries for recycling Warning Never lean over batteries while connecting you might get injured Battery fluid contains sulfuric acid Do not allow this fluid to come in contact with eyes skin or clothing In case it does immediately flush affected area with water and seek medical help A battery will also produce hydrogen gas which is flammable and explosive Keep flames or sparks away from battery avoid improper connection of jumper cables smoking etc 104 Exterior Lamps When replacing bulbs install only 12 volt bulbs with the specified watt rating PSd 0123 B22 Headlamp Assembly 1 2 Headlamp vertical adjustment screw Headlamp horizontal adjustment screw Clamp for high and low beam headlamp bulb cover Bulb socket for turn signal parking side marker and standing lamp bulb Electrical connector for high and low beam headlamp bulb 105 Replacing bulb When replacing halogen bulbs do not touch glass portion of bulb with bare hands Use plain paper or a clean cloth Warning Halogen lamps contain pressurized gas A bulb can explode if you e touch or move it when hot drop the bulb e scratch the bulb Bulb for high and low beam HB2 60 55 W Remove coyer above headlamp Move retaining clamps 5 aside and remove cover Pull off electrical connector 8 resp
19. other accidents without frontal forces the emergency tensioning retractors will not be activated The driver and passengers will then be protected by the fastened seat belts and inertia reel in the usual manner For seat belt and emergency tensioning retractor safety guidelines see Safety Guidelines in Index 49 Pas 0030 52 Airbags The most effective occupant restraint system yet developed for use in production vehicles is the seat belt In some cases however the protective effect of a seat belt can be further enhanced by an airbag The driver airbag 1 is located in the steering wheel hub The passenger airbag 2 is located in the dashboard ahead of the passenger In conjunction with wearing the seat belts with emergency tensioning retractors 4 they provide increased protection for the driver and passenger in certain major frontal and front angled impacts The operational readiness of the airbag system is verified by the indicator lamp SRS 3 in the instrument cluster If no fault is detected the lamp will go out after approximately 4 seconds after the lamp goes out the system continues to monitor the components and circuitry of the airbag system and will indicate a malfunction by coming on again 50 The following system components are monitored or undergo a self check crash sensor airbag ignition circuits driver and passenger seat belt buckles Initially when the key is turned from ste
20. parking and or headlamps on Rear fog lamp pull out to 2nd detent in addition to fog lamps Indicator lamp in lamp switch comes on Standing Lamps When the vehicle is parked on the street the standing lamps right or left side parking lamps can be turned on making the vehicle more visible to passing vehicles The standing lamps cannot be operated with the key in steering lock position 2 Note With the key removed and a front door open an audible warning will sound if the vehicle s exterior lamps except standing lamps are not switched off Fog lamps will operate with the parking lamps and the low or high beam headlamps Fog lamps should only be used in conjunction with low beam headlamps Consult your state Motor Vehicle Regulations regarding allowable lamp operation Fog lamps are automatically switched off when the exterior lamp switch is turned to position O 58 Inside and Exterior Rear View Mirrors Inside Rear View Mirror The mirror is electrically adjustable Use your inside mirror to determine the size and distance of objects seen in the passenger side convex mirror RAK The switch is located on the center console Turn key in steering lock to position 2 with either front door open the mirror can be operated with key removed or in steering lock position 0 or 1 Turn switch to position To adjust move the switch forward backward or to either side Antiglare Night Position
21. sharply increased when you drink and drive Please don t drink and drive or allow anyone to drive after drinking Parking Brake To engage firmly depress parking brake pedal When the key is in steering lock position 2 the brake warning lamp in the instrument cluster should come on brightly To release the parking brake pull handle on instrument panel The brake warning lamp in the instrument cluster should go out Also see Brake Warning Lamp Test in Index Driving Off Test the brakes briefly after driving off Perform this procedure only when the road is clear of other traffic Warm up the engine smoothly Do not place full load on the engine until the operating temperature has been reached Warning Keep driver s foot area clear at all times Objects stored in this area may impair pedal movement T2 Automatic Transmission The automatic transmission selects individual gears automatically dependent upon e Selector lever position e Accelerator position e Vehicle speed Important When parking the car and before working on the vehicle with the engine running firmly depress the parking brake pedal and shift the selector lever into P Driving The selector lever is automatically locked while in position P To move the selector lever out of position P the service brake pedal must be firmly depressed before the shift lock will release Shift selector lever to the desired driving pos
22. vehicle Post production treatment is neither necessary nor recommended by Mercedes Benz because of the possibility of incompatibility between materials used in the production process and others applied later We have selected car care products and compiled recommendations which are specially matched to our vehicles and which always reflect the latest techno logy You can obtain MB car care products at your authorized Mercedes Benz dealer Scratches corrosive deposits corrosion or damage due to negligent or incorrect care cannot always be removed or repaired with the car care products re commended here In such cases it is best to seek aid at your authorized Mercedes Benz dealer The following topics deal with the cleaning and care of your vehicle and give important how to information as well as references to recommended MB car care products Additional information can be found in the booklet titled Car Care 113 Engine Cleaning Corrosion protection such as MB Anticorrosion Wax should be applied to the engine compartment after every engine cleaning Before applying all control linkage bushings and joints should be lubricated The poly V belt and all pulleys should be protected from any wax Car Washing Before washing your vehicle remove insect residues MB Insect Remover is recommended Do not use hot water or wash your car in direct sunlight Use only a mild car wash detergent such as MB Autoshampo
23. wheels towards the road curb Turn the key to steering lock position 0 and remove So i pa Important It is advisable to set the parking brake whenever parking or leaving the vehicle In addition move selector lever to position P When parking on hills always set the parking brake 18 Winter Driving Instructions The most important rule for slippery or icy roads is to drive sensibly and to avoid abrupt acceleration braking and steering maneuvers Do not use the cruise control system under such conditions When the vehicle is in danger of skidding move selector lever to position N Try to keep the vehicle under control by corrective steering action Road salts and chemicals can adversely affect braking efficiency Increased pedal force may become necessary to produce the normal brake effect We therefore recommend depressing the brake pedal periodically when traveling at length on salt strewn roads This can bring road salt impaired braking efficiency back to normal A prerequisite is however that this is done without endangering other drivers on the road If the vehicle is parked after being driven on salt treated roads the braking efficiency should be tested as soon as possible after driving is resumed while observing the safety rules in the previous paragraph Warning If the vehicle becomes stuck in snow make sure that snow is kept clear of the exhaust pipe and from around the vehicle wi
24. windshield washer solvent antifreeze which is formulated for below freezing temperatures see Index e Test battery Battery capacity drops with decreasing ambient temperature A well charged battery ensures that the engine can always be started even at low ambient temperatures e Tires We recommend M S radial tires on all four wheels for the winter season Observe permissible maximum speed for M S radial tires and the legal speed limit Note In winter operation the maximum effectiveness of the acceleration slip control is only achieved with M S radial tires Snow Chains Important Use only snow chains that are tested and recommended by Mercedes Benz Your authorized Mercedes Benz dealer will be glad to advise you on this subject Chains should only be used on the rear wheels Follow the manufacturer s mounting instructions Snow chains should only be driven on snow covered roads at speeds not to exceed 30 mph 50 km h Remove chains as soon as possible when driving on roads without snow For tips on driving on slippery winter roads refer to Index Vehicles with Acceleration Slip Control ASR When driving with snow chains press the snow chain switch refer to Index 89 90 Practical Hints 91 Hood To open To unlock the hood pull release lever 1 under the driver s side of the instrument panel At the same time handle 2 will extend out of the radiator grill it may be nece
25. 0 kW 5200 rpm 320 ft lb 3800 rpm 570 Nm 3800 rpm 6000 rpm 1 12 5 8 3 1 6 7 2 11 4 9 2585 mm 124 mph 200 km h 79 mph 127 km h 46 mph 74 km h Rims Tires Rims light alloy rims Wheel offset or Rear axle Rims light alloy rims Wheel offset Summer tires Radial ply tires 7 2Jx16H2 2 0 in 51 mm 8Jx16H2 1 3 in 34 mm 235 60 ZR 16 100 H Winter tires Radial ply tires 235 60 R 16 100 H M S The quoted data apply only to the standard vehicle See an authorized Mercedes Benz dealer for the corresponding data of all special bodies and special equipment 2 Use Correct wheel bolts 3 Must not be used with winter tires and or snow chains 128 Technical Data S 600 Electrical System Main Dimensions Overall vehicle length 205 2 in 5213 mm Overall vehicle width 74 3 in 1886 mm Overall height 58 9 in 1495 mm Wheel base 123 6 in 3140 mm Track front Track rear Rims 7 4 Jx 16H2 Rims 8 Jx 16H2 63 1 in 1603 mm 62 0 in 1576 mm Alternator 14 V 120 A Starter motor 12 V 1 8 kW Battery 12 V 100 Ah Spark plugs Bosch F9 DCO Beru 14 F 9 DUO Champion S 12 YCC Electrode gap 0 032 in 0 8 mm Tightening torque 15 22 ft lb 20 30 Nm Weights See certification tag Roof load max 220 lb 100 kg Trunk load max 220 Ib 100 kg 129 Fuels Coolants Lubricants etc Capacities Vehicle components and their respective lubricant
26. 2 132 133 134 143 Instruments and Controls For more detailed descriptions see Index SPANK HAN hk WO NY pi p p p p pah pab ph pah oO la AA A WO NY D Adjustable air outlet Exterior lamp switch Parking brake release Hood lock release Parking brake pedal Steering wheel adjustment switch Combination switch Cruise control switch Horn airbag Instrument cluster Steering lock with preglow starter switch Adjustable air outlet Heated air supply button center air outlet Non heated coolant air supply button center air outlet Air volume control for left air outlet Air volume control for left center air outlet Air volume control for right center air outlet Air volume control for right air outlet 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Telephone control unit compartment Lock for telephone control unit compartment and glove box Glove box illuminated with key in steering lock position 2 Rear window defroster switch Switch for rear seat head restrains Active charcoal filter switch Central locking switch Indicator lamp for anti theft alarm system Hazard warning flasher switch Automatic climate control Radio Snow chain switch Ashtray with lighter Adaptive damping system adjustment switch Seat heater switch Mirror adjustment switch Switch for rear window sunshade Power window switch Seat belt extender 10 P63 0054 BI7A 11 I
27. 2 Soft damping program This setting should be used for regular driving Note The firm damping program must be selected again when restarting the engine 87 Emission Control Certain systems of the engine serve to keep the toxic components of the exhaust gases within permissible limits required by law These systems of course will function properly only when maintained strictly according to factory specifications Any adjustments on the engine should therefore be carried out only by qualified Mercedes Benz technicians Engine adjustments should not be altered in any way Moreover the specified service and maintenance jobs must be carried out regularly according to Mercedes Benz servicing requirements For details refer to the Maintenance Booklet Warning Inhalation of exhaust gas is hazardous to your health All exhaust gas contains carbon monoxide and inhaling it can cause unconsciousness and lead to death Do not run the engine in confined areas such as a garage which are not properly ventilated If you think that exhaust gas fumes are entering the vehicle while driving have the cause determined and corrected immediately If you must drive under these conditions drive only with at least one window fully open On Board Diagnostic System S 500 California version only S 600 all The Sequential Multiport Fuel Injection SFI control module monitors emission control components that either provide
28. 5 Reinstall cover above headlamp 107 om PSEOOSE IS Taillamp Assemblies 1 Turn signal lamp 21 W 32 cp bulb Backup lamp 21 W 32 cp bulb Stop side marker lamp 21 4 W 35 1 2 cp bulb Tail parking lamp 5 W bulb 5 Tail parking and standing lamp 21 4 W 35 1 2 cp bulb Driver s side Tail parking standing and rear fog lamp 21 4 W 35 1 2 cp bulb 6 Trunk lamp 10 W bulb To replace bulbs Turn locking lever on lamp cover to vertical position and swing open lamp support Push down on bulb to be changed twist counterclockwise and remove s E E A reparatia iina gea w w v w License Plate Lamps 5 W bulb Loosen both securing screws 1 remove lamp and take out bulb 108 High Mounted Stop Lamp H2 20W bulb To replace the bulb press tabs on both sides arrows to release cover Turn bulb socket with bulb counter clockwise and pull out Press bulb down turn counterclockwise and remove Main fuse box in engine compartment Fuses Before replacing a blown fuse determine the cause of the short circuit Spare fuses are supplied inside the main fuse box Observe amperage and color of fuse Auxiliary fuse box in trunk behind right side cover Always use a new fuse for replacement Never attempt to repair or bridge a blown fuse After replacing a blown fuse close fuse box cover 109 Jump Starting If the battery is discharged the engine shoul
29. 6 100 H Winter tires Radial ply tires 235 60 R 16 100 H M S The quoted data apply only to the standard vehicle See an authorized Mercedes Benz dealer for the corresponding data of all special bodies and special equipment 2 Use Correct wheel bolts 3 Must not be used with winter tires and or snow chains 126 Technical Data S 500 Electrical System Main Dimensions Overall vehicle length 205 2 in 5213 mm Overall vehicle width 74 3 in 1886 mm Overall height 58 9 in 1495 mm Wheel base 123 6 in 3140 mm Track front Track rear Rims 7 4 Jx 16H2 Rims 8 J x 16H2 63 1 in 1603 mm 62 0 in 1576 mm Alternator 14 V 120 A Starter motor 12 V 1 8 kW Battery 12 V 100 Ah Spark plugs Bosch F9 DCO Beru 14 F 9 DUO Champion S 12 YCC Electrode gap 0 032 in 0 8 mm Tightening torque 15 22 ft 1b 20 30 Nm Weights See certification tag Roof load max 220 lb 100 kg Trunk load max 220 lb 100 kg 127 Technical Data S 600 Model Engine Mode of operation No of cylinders Bore Stroke Total piston displacement Compression ratio Output acc to SAE J 1349 Maximum torque acc To SAE J 1349 Maximum engine speed Firing order Poly V belt length Transmission Downshift points D to 3 3 to2 2 to B S 600 140 076 120 4 stroke engine gasoline injection 8 3 50 in 89 00 mm 3 16 in 80 20 mm 365 4 cu in 5987 cm 10 1 389 hp 5200rpm 29
30. Air distribution buttons Defrost Residual engine heat utilization Air recirculation Air volume selector Economy Selection switch Off Patna Ra Right side passenger compartment Temperature selector Temperature display Automatic mode Air distribution buttons 23 The temperature selected with the temperature selector is reached as quickly as possible The temperature selector should be left at the desired temperature setting With the center air outlets open and the system in heating mode switch the outlets to non heated cooled air by pressing the blue button indicator lamp lights up With the center air outlets open and the system in cooling mode switch the outlets to non heated fresh air by pressing the red button indicator lamp lights up The system will not heat or cool any quicker by setting a higher or lower temperature The automatic climate control only operates with the engine running The automatic climate control removes considerable moisture from the air during operation in the cooling mode It is normal for water to drip on the ground through ducts in the underbody 1 12 Temperature Selector The desired interior temperature can be selected separately for the left and right side of the passenger compartment A basic setting in the white field of the selector is recommended and can be used for driving year round The selected temperature can be shown in the display windo
31. Board Diagnostic System Traveling Abroad Winter Driving Snow Chains Practical Hints Hood Checking Coolant Level 80 80 81 92 93 Adding Coolant Checking Engine Oil Level Checking Automatic Transmission Fluid Level Trunk Lamp Spare Wheel Lug Wrench First Aid Kit Stowing Things in the Vehicle Vehicle Jack Vehicle Tools Storage Compartment below Vehicle Tool Box Wheels Changing Wheels Tire Inflation Pressure Battery Exterior Lamps Fuses Jump Starting Towing the Vehicle Cleaning and Care of the Vehicle Testing Infrared Remote Control Front Head Restrains Rear Seat Cushion Manual Closing of Trunk Lid Manual Retraction of Trunk Lid Handle Replacing Wiper Blades Emergency Operation of Sliding Roof Manual Release of Fuel Filler Flap Layout of Poly V Belt Drive Roof Rack Mercedes Benz Spare Parts Service Technical Data Fuels Coolants Lubricants etc Consumer Info Identification Plates Vehicle Data Card Warranty Coverage Technical Data S 500 S 600 Fuels Coolants Lubricants etc Capacities Engine Oils Engine Oils Additives Air Conditioner Refrigerant Brake Fluid Premium Unleaded Gasoline Fuels Requirements Gasoline Additives Coolants Check Regularly and before a long trip 120 121 120 122 122 124 125 125 126 128 130 132 132 132 131 13
32. Control with Foldering Master Key The master key fits all locks on the car The transmitter for the infrared remote control is located in the key holder the receivers are located in the door handles and next to the trunk lock Master Key The master key fits all locks on the car Valet Key The valet key fits only the door locks and the steering lock The valet key will not fit the trunk lock or storage compartments lock in the dashboard Flat Key The flat key fits all locks on the car Notes Do not give the master key to an unauthorized person We recommend that you carry the flat key with you and keep it in a safe place e g your wallet so that it is always handy Never leave the flat key in the vehicle Warning When leaving the vehicle always remove the key from the steering lock Do not leave children unattended in the vehicle Unsupervised use of vehicle equipment may cause serious personal injury Obtaining Replacement Keys Your vehicle is equipped with a theft deterrent locking system requiring a special key manufacturing process For security reasons replacement keys can only be obtained from your authorized Mercedes Benz dealer 28 Master Key in Key Holder 1 Release button for master key Releasing press release button 1 The key unfolds from the holder by itself Storing press release button 1 and fold key back into holder Infrared Remote Control 1 Transm
33. Rear Armrest Front Armrest Rear Adjustable Steering Wheel Seat Belts and Supplemental Restrain System SRS Seat Belts Emergency Tensioning Retractor ETR Airbags Steering Lock Combination Switch Exterior Lamp Switch Inside and Exterior Rear View Mirrors Sun Visors Vanity Mirrors Interior Lighting 33 Storage Compartments Ashtrays 34 Lighter Sliding Roof with Rear 35 Pop Up Feature 36 Power Windows 37 Rear Window Sunshade 40 _Rear Window Defroster 40 Setting Clock 41 Shelf below Rear Window 42 Antenna 43 Cellular Telephone 43 Driving Drinking and Driving 45 Parking Brake 49 Driving Off Automatic Transmissions 50 Rear Fender Indicators 55 Cruise Control 56 Charge Indicator Lamp 58 Engine Oil Pressure Gauge with Oil Pressure Warning Lamp 59 Low Engine Oil Level 62 _Warning Lamp 62 Engine Oil Consumption 63 Fuel Consumption Gauge Fuel Reserve Warning Lamp Outside Temperature Indicator Coolant Temperature Gauge Low Engine Coolant Level Warning Lamp Low Windshield and Headlamp Washer System Fluid Level Warning Lamp Exterior Lamp Failure Indicator Lamp Seat Belt Warning Lamp Brake Pad Wear Indicator lamp Brake Warning Lamp Antilock Brake System ABS Acceleration Slip Control ASR Driving with Snow Chains Adaptive Damping System ADS Emission Control On
34. With the key in steering lock position 2 the mirror responds to changes in light sensitivity 59 Cl Exterior rear view mirror left m Exterior rear view mirror right Exterior Rear View Mirrors Turn key in steering lock to position 2 with either front door open the mirrors can be operated with key removed or in steering lock position 0 or 1 Turn switch to select the mirror to be adjusted To adjust move the switch forward backward or to either side Note The exterior mirrors have electrically heated glass The heater switches on automatically depending on outside temperature If an exterior mirror housing is forcibly pivoted from its normal position it must be repositioned by applying firm pressure until it snaps into place Warning Exercise care when using the passenger side mirror The passenger side exterior mirror is convex outwardly curved surface for a wider field of view Objects in mirror are closer than they appear Check your inside rear view mirror or glance over your shoulder before changing lanes 60 Exterior Rear View Mirror Multiple Images This vehicle is equipped with anti fogging dual pane side windows to provide extra insulation against heat cold and noise Because of the second pane of glass under certain light and weather conditions a multiple image may become noticeable especially when looking through the side windows at an outside rear view mirror St
35. Your car is covered under the terms of the warranties printed in the Owner s Service and Warranty Policy Booklet and your authorized Mercedes Benz dealer will exchange or repair any defective parts in accordance with the terms of the following warranties New vehicle limited warranty Emission systems warranty Emission performance warranty California emission control system system warranty So Loss of Owner s Service and Warranty Policy Should you lose your Owner s Service and Warranty Policy Booklet have your authorized Mercedes Benz dealer arrange for a replacement It will be mailed to you 125 Technical Data S 500 Model Engine Mode of operation No of cylinders Bore Stroke Total piston displacement Compression ratio Output acc to SAE J 1349 Maximum torque acc To SAE J 1349 Maximum engine speed Firing order Poly V belt length Transmission Downshift points D to 3 3 to2 2 to B S 500 140 051 119 4 stroke engine gasoline injection 8 3 80 in 96 50 mm 3 35 in 85 00 mm 303 5 cu in 4937 cm 10 1 315 hp 5600rpm 235 kW 5600 rpm 347 ft lb 3900 rpm 470Nm 3900 rpm 6000 rpm 1 5 4 8 6 3 7 2 2460 mm 124 mph 200 km h 79 mph 127 km h 46 mph 74 km h Rims Tires Rims light alloy rims 7 Jx16H2 Wheel offset 2 0 in 51 mm or Rear axle Rims light alloy rims 8Jx16H2 Wheel offset 1 3 in 34 mm Summer tires Radial ply tires 235 60 ZR 1
36. ack of the head approximately at ear level The head restraint inclination can also be adjusted manually Note Your car is equipped with power head restraints do not try to raise or lower them manually Power Seats Front Warning Do not adjust the driver s seat while driving Adjusting the seat while driving could cause the driver to lose control of the vehicle Never ride in a moving vehicle with the seat back reclined Sitting in an excessively reclined position can be dangerous You could slide under these at belt in a collision If you slide under it the belt would apply force at the abdomen or neck That could cause serious or even fatal injuries The seat back and seat belts provide the best restraint when the wearer is in an upright position and belts are properly positioned on the body Never place hands under or near any moving parts while a seat is being adjusted 37 F Memory button G Position buttons Storing seat head restraint steering wheel exterior and inside rear view mirror positions in memory Three sets of seat head restraint steering wheel exterior and inside rear view mirror positions may be programmed into memory After the seat head restraint steering wheel exterior and inside rear view mirrors are positioned push memory button F release and within 3 seconds push position button 1 A second and third set of positions for the same seat head restraint steering wheel exteri
37. an 2 3 of maximum permissible speed in each gear as indicated on the speedometer Avoid accelerating by kickdown It is not recommended to brake the vehicle by manually shifting to a lower gear We recommend to select positions 3 or 2 only at moderate speeds for hill driving After 1000 miles 1500 km speeds may be gradually increased to the permissible maximum Maintenance We strongly recommend that you have your vehicle serviced by your authorized Mercedes Benz dealer in accordance with the Maintenance Booklet Failure to have the vehicle maintained in accordance with the Maintenance Booklet may result in vehicle damage not covered by the Mercedes Benz Limited Warranty Introduction Product information Operator s manual Consumer Information Problems with your vehicle Reporting Safety Defects Index Instruments and Controls Instruments and Controls Instrument Cluster Indicator Lamp Symbols Starting and Turning Off the Engine Driving Instructions Operation Air Outlets Automatic Climate Control Rear Passenger Compartment Adjustable Air Outlet Active Charcoal Filter Car Keys Infrared Remote Control Central Locking System Doors 135 136 137 139 Trunk Power Windows and Sliding Pop Up Roof Power Closing Assist for Doors and Trunk Lid Anti Theft Alarm System Power Seats Front Lumbar Support Multicontour Backrest Heated Seats Power Head Restrains
38. an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Mercedes Benz of North America Inc To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 or 366 0123 in Washington D C area or write to NHTSA U S Department of Transportation Washington D C 20590 You can also obtain other information about motor vehicle safety from the Hotline 137 Index 138 ABS 75 84 Acceleration slip control ASR 85 Activated charcoal filter 27 Adaptive damping system ADS 87 ADS 87 130 Air conditioner refrigerant 132 Air outlets 22 Airbag 50 Alarm system 36 Antenna 70 Anti theft alarm system 36 Anticorrosion antifreeze 89 93 131 134 Antilock brake system ABS 84 Armrest front 43 Armrest rear 43 Ashtrays 65 ASR 85 Automatic climate control 23 Automatic transmission 73 Automatic transmission fluid level checking 95 Battery 104 Battery not being charged Charge indicator lamp 15 78 Brake fluid 17 83 113 130 132 Brake pads worn Brake pad wear indicator lamp 82 Brake warning lamp Brake fluid low 83 Brake warning lamp test 83 Brakes 16 18 72 74 75 77 85 112 Capacities Fuels coolants lubricants etc 130 Catalytic converter 14 Cellular telephone 70 Central locking system 32
39. and Warranty Policy The Owner s Service and Warranty Information Booklet contains detailed information about the warranties covering your Mercedes Benz including e New Car Limited Warranty Emission System Warranty e Emission Performance Warranty e State Warranty Enforcement Laws Lemon Laws Important notice for California retail buyers of Mercedes Benz automobiles Under California law you may be entitled to a replacement of your vehicle or a refund of the purchase price if Mercedes Benz USA LLC or its authorized Mercedes Benz Center fails to conform the vehicle to its express warranties after a reasonable number of repair attempts during the period of one year or 12 000 miles from original delivery of the vehicle A reasonable number of repair attempts is presumed for a retail buyer 1 if the vehicle is out of service by reason of repair of substantial nonconformities for a cumulative total of more than 30 calendar days or 2 the same substantial non conformity has been subject to repair four or more times and you have at least once directly notified us in writing of the need to repair the non conformity and have given us an opportunity to perform the repair ourselves Notifications should be sent to the nearest Mercedes Benz Regional Office listed in the Service and Warranty Information Booklet Maintenance The Service Booklet describes all the necessary maintenance work which should be performed at regular intervals Always ha
40. and hold on to it until possible pressure in tank has been released then remove cap Failure to do so could result in personal injury Tire Inflation Pressure Check at least every two weeks For details see Index Coolant Level See Adding coolant in Index Windshield Washer System Headlamp Cleaning System For refilling reservoir see Index Engine Oil Level See Index Brake Fluid See Index Vehicle Lighting Check function and cleanliness For replacement of light bulbs see Index 143 What You Should Know at the Gas Station e Fuel Use premium unleaded gasoline Posted Octane Index 91 Average of 96 RON 86 MON Fuel tank capacity approx 26 4 US gal 100 1 This includes approx 3 3 US gal 12 5 1 reserve Only fill fuel tank until the filler nozzle unit cuts out do not overfill Warning Gasoline is highly flammable It burns violently and can cause serious injury Whenever you are around gasoline extinguish all smoking materials Never allow sparks flame or smoking materials near gasoline e Engine Oil Engine oil level check see Index Fill quantity between upper and lower dipstick marking level 2 1 US qt 2 0 1 Recommended engine oils see Index e Automatic Transmission Automatic transmission fluid For level checks refer to Index Coolant For normal replenishing use water potable water quality For further information e g anticorrosion antifreeze refer to Index Spark P
41. approximately 5 minutes after stopping the engine allowing for the oil to return to the oil pan Wipe the dipstick clean before checking 94 Checking Automatic Transmission Fluid Level Dipstick locking lever 1 Break seal 2 Release 3 Engage Regular automatic transmission fluid level checks are not required For this reason the dipstick opening is sealed When noticing fluid loss or gear shifting malfunctions we recommend to have your authorized Mercedes Benz dealer check the transmission fluid level The transmission fluid level should only be checked with the engine idling parking brake engaged and selector lever in position P The vehicle must be parked on level ground Prior to the check allow engine to idle for approx 1 to 2 minutes To pull dipstick from tube break seal by moving plastic pin 1 sideways Then open cap by releasing locking lever 2 Measure fluid level with the dipstick completely inserted and the locking lever released 2 Extreme cleanliness must be observed To wipe the dipstick use a clean lint free cloth To fill the transmission with fluid pour it through a fine mesh filter into the dipstick opening Even the slightest impurity may cause operational troubles The level of the transmission fluid is dependent upon its temperature Two sets of maximum and minimum fluid level marks on the dipstick are applicable references only if the transmission fluid has either
42. ar wheel brakes Notes With the key in steering lock position 2 the yellow function indicator lamp and the yellow ASR warning lamp in the instrument cluster come on They must go out when the engine is running If the ASR warning lamp comes on with the engine running a malfunction has been detected Pressing the accelerator pedal will require greater effort Only partial engine output is available Have the acceleration slip control checked at your authorized Mercedes Benz dealer as soon as possible Driving the vehicle with varied size tires will cause the wheels to rotate at different speeds therefore the acceleration slip control will activate yellow ASR function indicator lamp in instrument cluster comes on For this reason all wheels including the spare wheel must have the same tire size When testing the parking brake on a brake test dynamometer the key must not be in steering lock position 2 Otherwise the acceleration slip control will immediately be engaged and will apply the rear wheel brakes In winter operation the maximum effectiveness of the acceleration slip control is only achieved with Mercedes Benz recommended M S radial ply tires The brake pad wear warning lamp indicates brake pad wear for the front as well as the rear brakes 85 Snow chain switch Pat 031413 Driving with Snow Chains When driving with snow chains press the upper half of the snow chain switch loc
43. ate gently and never abruptly step on the accelerator To rock a car out of soft ground mud or snow alternately shift from forward to reverse while applying slight partial throttle Rocking a car free in this manner may cause the ABS warning lamp to come on Turn off and restart the engine to clear the malfunction indication Stopping For brief stops e g at traffic lights leave the transmission in gear and hold vehicle with the service brake For longer stops with the engine idling shift into N or P When stopping the car on an uphill incline do not hold it with the accelerator use the brake This avoids unnecessary transmission heat build up Warning Getting out of your car with the selector lever not fully engaged in position P is dangerous When parked on an incline position P alone may not prevent your vehicle from moving possibly hitting people or objects Always set the parking brake in addition to shifting to position P When parked on an incline also turn downhill side of front wheel against curb 75 Rear Fender Indicators When the reverse gear is selected the rear fender indicators will extend upward from the rear corners of the fenders The rear fender indicators retract delayed when shifting out of reverse They retract immediately when turning key in steering lock to position 0 Note Before shifting into reverse gear ensure that the rear fender indicators can
44. ated on the instrument panel the indicator lamp in the switch comes on This mode is effective at speeds up to 25 mph 40 km h It remains stored in memory up to 37 mph 60 km h and automatically engages again when the vehicle speed drops below 25 mph 40 km The mode is canceled in memory above 37 mph 60 km h and the indicator lamp in the switch goes out To switch off press lower half of switch the indicator lamp in the switch goes out 86 Adaptive Damping System ADS Depending upon road surface conditions load driving style ADS will automatically adjust the optimal ride firmness The indicator lamp comes on with the key in steering lock position 2 and goes out when the engine is running If the indicator lamp stays on after the engine is running or comes on while driving then the system has detected a malfunction Pa2 003 B14 We recommend that you visit an authorized Mercedes Benz dealer as soon as possible to have the system checked out Note If the battery was disconnected the indicator lamp will only go out after the engine is started and the steering wheel is turned from full left to full right lock and returned to the center position Adaptive Damping System Adjustment The switch is located in the center console 1 Firm damping program This setting should be used for sporty driving During the setting for sporty driving the indicator lamp in the switch lights up
45. ater or commercially available premixed windshield washer solvent antifreeze depending on ambient temperature see Index at the next opportunity The reservoir for the windshield and headlamp washer system is located in the engine compartment next to the radiator The fluid level can be checked visually at the sight glass located next to the reservoir filler cap 81 Exterior Lamp Failure Indicator Lamp With the key in steering lock position 2 a dim indicator lamp comes on and goes out when the engine is running With the key in steering lock position 2 or with the engine running a bright illumination of this lamp indicates an exterior lamp failure If an exterior lamp fails the indicator lamp will come on only when that lamp is switched on If a brake or turn signal lamp fails the lamp failure indicator will come on when applying the brake or actuating the turn signal and stay on until the engine is turned off Note The indicator lamp will also come on if an incorrect bulb is installed If additional lighting equipment is installed e g auxiliary headlamps etc be certain to connect into the fuse before the failure indicator monitoring unit in order to avoid damaging the system Seat Belt Warning Lamp With the key in steering lock position 2 the warning lamp comes on and an audible warning sounds for a short time if the driver s seat belt is not fastened After starting the engine the warning
46. avoid wearing your seat belt 51 Important The SRS is designed to reduce the potential of injury in certain frontal and front angled impacts which may cause injuries however no system available today can totally eliminate injuries and fatalities The activation of the SRS temporarily releases a small amount of dust from the air bags This dust however is neither injurious to your health nor does it indicate a fire in the vehicle The service life of the airbags extends to the date indicated on the label located on the driver side door latch post To provide continued reliability after that date they should be inspected by an authorized Mercedes Benz dealer at that time and replaced when necessary Warning It is very important for your safety to always be in a properly seated position and to wear your seat belt For maximum protection in the event of a collision always be in normal seated position with your back against the seat back Fasten your seat belt and ensure that it is properly positioned on the body Since the airbag inflates with considerable speed and force a proper seating position will keep you in a safe distance from the airbag e Sit properly belted in an upright position with your back against the seat back e Adjust the driver seat as far as possible rearward still permitting proper operation of vehicle controls Do not lean with your head or chest close to the steering whe
47. ays follow the instructions on the particular container Always open your car s doors or windows when cleaning the inside Never use fluids or solvents that are not designed for cleaning your car In operation your vehicle is subjected to varying external influences which if gone unchecked can attack the paint work as well as the underbody and cause lasting damage Such damage is caused not only by extreme and varying climatic conditions but also by air pollution road salt tar gravel and stone chipping Grease and oil fuel coolant brake fluid bird droppings tree resins etc should be removed immediately to avoid paint damage Frequent washing however reduces and or eliminates the aggressiveness and potency of the above adverse influences More frequent washings are necessary to deal with unfavorable conditions for example near the ocean in industrial areas smoke exhaust emissions or during winter operation You should check your vehicle from time to time for stone chipping or other damage Any damage should be repaired as soon as possible to prevent the start of corrosion In doing so do not neglect the underside of the car A prerequisite for a thorough check is a washing of the underbody followed by a thorough inspection Damaged areas need to be reundercoated Your vehicle has been treated at the factory with a wax base rust proofing in the body cavities which will last for the lifetime of the
48. back covering material and pull head restraint up sharply holding it by the left head restraint post viewed in driving direction Pull out head restraint completely with both hands Installation Push button 1 up for approximately 5 seconds Insert the head restraint and push it down to the stop Adjust head restraint to the desired position Warning For your protection drive only with properly positioned head restraints Do not drive the vehicle without the seat head restraints Head restraints are intended to help reduce injuries during an accident For positioning of head restraints refer to sections Power Seats Front and Head Restraints Rear in Index 117 Rear Seat Cushion Removal Push in locking tabs 1 on left and right side of seat and pull up seat at the front Installation Slide rear edge of cushion under the backrest so that both wire loops under the backrest engage at the seat cushion Push front of cushion down until it locks in place Caution Watch out for sharp edges when removing or installing the rear seat cushion and make sure that it is securely locked in place again to prevent injury Manual Closing of Trunk Lid The trunk lid can be closed manually should a malfunction occur on the power closing system With the trunk lid open push sliding switch to position 1 press eye of latch in 2 push sliding switch to position 3 Close trunk lid Ese
49. can be removed from the steering lock only with the selector lever in position P With the key removed the selector lever is locked in position P R Reverse gear Shift to reverse gear only with the car stopped N Neutral No power is transmitted from the engine to the rear axle When the brakes are released the vehicle can be moved freely pushed or towed Do not engage N while driving except to coast when the vehicle is in danger of skidding e g on icy roads see Winter Driving Instructions in Index Important Coasting the vehicle or driving for any other reason with selector lever in N can result in transmission damage that is not covered by the Mercedes Benz Limited Warranty D The transmission automatically upshifts to 5th gear Position D provides optimum driving characteristics under all normal operating conditions 4 Upshift to 4th gear only Suitable for performance driving 3 Upshift to 3rd gear only Suitable for moderately steep hills Since the transmission does not shift higher than 3rd gear this gear selection will allow use of the engine s braking power downhill B Upshift to 2nd gear only For driving in mountainous regions or under extreme operating conditions This gear selection will allow use of the engine s braking power when descending steep grades Important With selector lever in position D 4 or 3 upshifting from 2nd to 3rd gear is delayed depending on ve
50. cessive heat build up and possible tire failure 135 Problems with your Vehicle If you should experience a problem with your vehicle particularly one that you believe may affect its safe operation we urge you to immediately contact your authorized Mercedes Benz dealer to have the problem diagnosed and corrected if required If the matter is not handled to your satisfaction please discuss the problem with the dealership management or if necessary contact the Owner Service Manager at the Mercedes Benz Regional Office nearest you see Owner s Service and Warranty Information booklet for addresses You may also write directly to us at the following addresses In the U S A Owner Service Department Mercedes Benz of North America Inc One Mercedes Drive Montvale NJ 07645 0350 In Canada Owner Service Department Mercedes Benz Canada Inc 849 Eglinton Avenue East Toronto Ontario M4G 2L5 136 For the U S A only The following text is published as required of manufacturers under Title 49 Code of U S Federal Regulations Part 575 pursuant to the National Traffic and Motor Vehicle Safety Act of 1966 Reporting Safety Defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying Mercedes Benz of North America Inc If NHTSA receives similar complaints it may open
51. cking the vehicle or when opening either front door However there will be no delay when the key is in steering lock position 2 B Interior lamps switched off 2 Interior Lamps Entrance Lamps Exit Lamps A a B The lamps are switched on and off by aa the door contact switches A Interior lamps switched off B Interior lamps switched on Note 3 Rear Courtesy Lamps To prevent the vehicle battery from being discharged do not leave doors A B open for a long period of time A Courtesy lamps switched off B Courtesy lamps switched on Note The courtesy lamps cannot be switched off as long as a rear door is open 4 Reading Lamps Front A Reading lamp switched off B Reading lamp switched on 63 Storage Compartments in the Dashboard 1 2 AU Storage eyeglasses compartment Button for storage eyeglasses compartment Glove box Button for glove box Lock Storage Eyeglasses Compartment To open Press button 2 Glove Box The glove box lid is equipped with a container for coins and small accessories To open Press button 4 Note The storage compartments may be locked and unlocked by using the master key in lock 5 Locking Turn master key in lock 5 to the right and remove Unlocking Turn master key back to vertical position Storage Compartment between Rear Seats Lock only when compartment is fully closed otherwise the lock may get damaged OLEA ON EPRE SO
52. console Both head restraints together can be placed in either upright or fold down position Switches in rear center console The head restraints can be placed individually in either upright or fold down position Inclination of head restraints The head restraint inclination can be adjusted manually Important For safety reasons always drive with the rear head restraints in the upright position when the rear seats are occupied Keep area around head restraints clear of articles e g clothing to not obstruct the folding operation of the head restraints 42 Armrest with Compartment for Telephone Handset Front Seats 1 Armrest folded down 2 Normal use 3 comfort positions 3 Armrest folded up Folding down Raise armrest past top comfort position and push down Adjusting height Raise armrest to desired position Press button 4 to open cover Warning The armrest does not suffice as a child restraint system In case of a frontal collision a child can be catapulted forward over the locked armrest Infants and small children should always be seated in a properly secured restraint system that complies with U S Federal Motor Vehicle Safety Standard 213 and Canadian Motor Vehicle Safety Standard 213 1 HE iP QE 1915 Armrest with integrated Storage Compartment Rear Seats Pull down the armrest by its strap Before storing the armrest in the backrest close its storage compartment lid
53. d leather as its underside should not become wet Paintwork Painted Body Components MB Gloss Preserver should be applied when water drops on the paint surface do not bead up normally in 3 to 5 months depending on climate and washing detergent used MB Paint Polish should be applied if paint surface shows signs of dirt embedding i e loss of gloss MB Fine Polishing Paste must be used when the paint surface shows signs of excessive fading chalking due to lack of care etc Do not apply any of these products or wax if your car is parked in the sun or if the hood is still hot Use the appropriate MB Touch Up Stick for quick and provisional repairs of minor paint damage i e chips from stones car doors etc Light Alloy Wheels MB Autoshampoo should be used for regular cleaning of the light alloy wheels If possible clean wheels once a week with MB Autoshampoo using a soft sponge and an ample supply of lukewarm water If the MB Autoshampoo does not satisfactorily clean the wheels use MB Protective Agent for Light Alloy Wheels for normal cleaning and MB Cleaner for Light Alloy Wheels for heavier dirt accumulation Follow instructions on container Ornamental Moldings For regular cleaning and care of very dirty chrome plated parts use a chrome cleaner Automatic Antenna and Rear Fender Indicators For trouble free operation of the automatic antenna and rear fender indicators we recommend to clean them
54. d be started with jumper cables and the 12 V battery of another vehicle The battery is located in the trunk behind the right hand cover panel Warning Failure to follow these directions will cause damage to the electronic components and can lead to a battery explosion and personal injury Read all instructions before proceeding Proceed as follows 1 Position the vehicle with the charged battery so that the jumper cables will reach but never let the vehicles touch Make sure the jumper cables do not have loose or missing insulation 2 On both vehicles Turn off engine and all lights and accessories except hazard flashers or work lights e Apply parking brake and shift selector lever to position P Important 3 Clamp one end of the first jumper cable to the positive terminal of the discharged battery and the other end to the positive terminal of the charged battery Make sure the cable clamps do not touch any other metal parts Clamp one end of the second jumper cable to the grounded negative terminal of the charged battery and the final connection to the negative terminal of the discharged battery 110 Important 5 Start engine of the vehicle with the charged battery and run at high idle Then start engine of the disabled vehicle in the usual manner 6 After the engine has started remove jumper cables by exactly reversing the above installation sequence star
55. des Benz dealer or write to In the USA In Canada Mercedes Benz USA Mercedes Benz Canada Inc LLC European Delivery Department European Delivery Department One Mercedes Drive 849 Eglinton Avenue East Montvale NJ 07645 Toronto Ontario M4G 2L5 We continuously strive to improve our product and ask for your understanding that we reserve the right to make changes in design and equipment Therefore information illustrations and descriptions in this Operator s Manual might differ from your vehicle Optional equipment is also described in this manual including operating instructions wherever necessary Since they are special order items the descriptions and illustrations herein may vary slightly from the actual equipment of your vehicle If there are any equipment details that are not shown or described in this Operator s Manual your authorized Mercedes Benz Center will be glad to inform you of correct care and operating procedures The Operator s Manual and Service Booklet are important documents and should be kept with the vehicle Check Regularly and Before a Long Trip See Index The First 1000 Miles 1500 km The more cautiously you treat your vehicle during the break in period the more satisfied you will be with its performance later on Therefore drive your vehicle during the first 1500 km 1000 miles at moderate vehicle and engine speeds During this period avoid heavy loads full throttle driving and high RPM no more th
56. dow is completely closed and hold for additional 2 seconds Repeat procedure for each window The automatic full opening and closing procedure of the windows should now be restored Rear Window Sunshade 1 Raising 2 Lowering The switches are located on the center console and between the single rear seats The sunshade should always be either fully raised or fully lowered 68 Rear Window Defroster The switch is located in the center console Turn key in steering lock to position 1 or 2 When activating the rear window defroster the indicator lamp in the switch will come on Note The rear window defroster uses a large amount of power To keep the battery drain to a minimum turn off the defroster as soon as the window is clear The defroster is automatically turned off after a maximum of 20 minutes of operation Heavy accumulation of snow and ice should be removed before activating the defroster If several power consumers are turned on simultaneously or the battery is only partially charged it is possible that the defroster will automatically turn itself off When this happens the indicator lamp inside the switch starts blinking As soon as the battery has sufficient voltage the defroster automatically turns itself back on Setting Clock Adjusting clock one minute ahead or back Pull out adjustment knob 1 briefly turn to the right respectively left and release knob Adjust
57. driving in stop and go traffic This precaution helps to avoid draining of the battery Unnecessary strain on the battery and charging system may be minimized by turning off the following power consumers for example Heated seats rear window defroster In addition the automatic climate air volume control should be set to MIN Caution To prevent accelerated battery discharge and a possible dead battery always remove the key from the steering lock Do not leave the key in steering oock position 0 55 Pa2 0075 613 Combination Switch 1 Low beam exterior lamp switch position 2 High beam exterior lamp switch position 2 High beam flasher high beam available independent of exterior lamp switch position Turn signals right Turn signals left T pag o006 B13 To signal minor directional changes such as changing lanes on a highway move combination switch to the point of resistance only and hold it there To operate the turn signals continuously move the combination switch past the point of resistance up or down The switch is automatically canceled when the steering wheel is turned to a large enough degree 6 Press switch briefly One wipe without washer water select only if window is wet Press switch past resistance point Windshield washer windshield wiper headlamp cleaning system only in exterior lamp switch positions or 2D 7 Windshield wiper 0 Wiper off I Intermi
58. e lamp comes on when the engine is running it indicates a malfunction of the fuel injection system or emission control system In either case we recommend that you have the malfunction checked as soon as possible See Index 13 Catalytic Converter Your Mercedes Benz is equipped with monolithic type catalytic converters an important element in conjunction with the O2 sensor to achieve substantial control of the pollutants in the exhaust emissions Keep your vehicle in proper operating condition by following our recommended maintenance instructions as outlined in your Maintenance Booklet Caution To prevent damage to the catalytic converters use only premium unleaded gasoline in this vehicle Any noticeable irregularities in engine operation should be repaired promptly Otherwise excessive unburned fuel may reach the catalytic converter causing it to overheat Warning As with any vehicle do not idle park or operate this vehicle in areas where combustible materials such as grass hay or leaves can come into contact with the hot exhaust system as these materials could be ignited 14 Starting and Turning Off the Engine Before Starting Engage parking brake and ensure selector lever is in position P or N Turn key in steering lock to position 2 The charge indicator lamp should come on Cold Engine Do not depress accelerator Turn key in steering lock clockwise to the stop Release key only when th
59. e natural laws of physics from acting on the vehicle The ABS cannot prevent accidents including those resulting from excessive speed in turns following another vehicle too closely or aquaplaning Only a safe attentive and skillful driver can prevent accidents The capabilities of an ABS equipped car must never be exploited in a reckless or dangerous manner which could jeopardize the user s safety or the safety of others Note To alert following vehicles to slippery road conditions you discover operate your hazard warning flashers as appropriate 84 Acceleration Slip Control ASR The acceleration slip control will engage at all vehicle speeds if one or both drive wheels begin to lose traction and spin While engaged the yellow function indicator in the speedometer lights up With the acceleration slip control engaged the brake is applied to the spinning drive wheel until it regains sufficient traction If both drive wheels lose traction and spin the brake is applied to both drive wheels and simultaneously engine torque is limited As traction on the road surface increases the allowable engine torque also increases again and the brake is no longer applied to drive wheels Caution If the vehicle is towed with the front axle raised see Towing the vehicle in Index the key must not be in steering lock position 2 Otherwise the acceleration slip control will immediately be engaged and will apply the re
60. e engine is firing regularly Hot Engine Do not depress accelerator Turn key in steering lock clockwise to the stop If the engine has not fired after approx 4 seconds depress accelerator and continue cranking until the engine is firing regularly Release key and back off accelerator At very high coolant temperatures the engine starting time can be shortened if the accelerator is depressed slowly at the beginning of the starting process Turning Off Turn the key in the steering lock to position 0 to stop the engine The key can only be removed with the selector lever in position P If the coolant temperature is very high e g after hard driving on mountain roads do not shut off the engine immediately but allow it to run for 1 2 minutes at increased idle speed with selector lever in position P or N Important Due to the installed starter non repeat feature the key must be turned completely to the left before attempting to start the engine again Observe the oil pressure gauge immediately after starting the engine In a very cold engine the oil pressure will rise slowly after the engine has started Do not speed up the engine before pressure is registered on the pressure gauge If you do not see the gauge register oil pressure stop the engine and have it checked The charge indicator lamp should go out as soon as the engine has started In areas where temperatures frequently drop below 4
61. e wiper blade Installation Place wiper blade on wiper arm and press in pin 1 Emergency Operation of Sliding Roof The sliding roof can be opened or closed manually should an electrical malfunction occur Fold back access cover in left side panel of trunk with a screwdriver Insert socket wrench from tool kit through opening in panel and place on the hex drive of the electric motor Turn socket wrench manually to open or close roof as desired To slide the roof closed or to raise the roof at the rear turn clockwise To slide the roof open or to lower the roof at the rear turn counterclockwise 120 PATOSE IS Manual Release of Fuel Filler Flap The manual release knob is located behind the right side trunk panel and felt pad In case the central locking system does not release the fuel filler flap pull the manual release knob while simultaneously opening the fuel filler flap S 500 Layout of Poly V belt Drive 1 Automatic belt tensioner 2 Crankshaft 3 Air conditioning compressor 4 Fan 5 Air pump S 600 6 Alternator 7 Idler pulley 8 Power steering pump 9 Coolant pump For dimensions of the poly V belt see Technical Data in Index 121 Roof Rack Use only those roof racks approved by Mercedes Benz to avoid damage to the vehicle Follow manufacturer s installation instructions Mount supports only between markings on border of roof which are visible when d
62. ectively 9 Unhook clamping ring and pull out bulb together with clamping ring Remove bulb Insert new bulb seating properly in cutouts of bulb socket mount clamping ring Reinstall and push electrical connector on securely Reinstall cover and fasten with retaining clamps 3 Turn Signal Parking Side Marker and Standing Lamp 2357 NA 28 5 8 3 W 30 2 2 cp bulb Replacing bulb Twist bulb socket 4 counterclockwise and pull out Push bulb into socket turn counterclockwise and remove Insert new bulb in socket and twist clockwise Reinstall bulb socket twist clockwise 106 Adjusting Headlamp Correct headlamp adjustment is extremely important To check and readjust a headlamp do the following e Park unloaded vehicle on level surface Check with carpenter s level e Remove cover above head lamp Move retaining clamp 3 aside and remove cover Note Horizontal headlamp aim normally never changes and needs readjustment only after repair to the body or a headlamp unit Therefore do not turn the horizontal adjustment screw 2 if pins in sight glasses 7 and 8 show the same value Pod 0t25 Boda Vertical headlamp aim Turn adjusting screw 1 until bubble in level 6 is in center of the marking bold line Horizontal headlamp aim Turn adjustment screw 2 until pins in sight glasses 7 and 8 show the same value 4 Reinstall cover and fasten with retaining clamp 3
63. el or dashboard e Adjust the passenger seat as far as possible rearward from the dashboard e Infants and small children should only be seated in a rear seat and be properly secured in a child restraint system e Rear facing child restraints must not be used in a front seat with a passenger side airbag Failure to follow these instructions can result in severe injuries to you or other occupants 52 Safety Guidelines for the Seat Belt Emergency Tensioning Retractor and Airbag Warning e Damaged belts or belts that were highly stressed in an accident must be replaced and their anchoring points must also be checked Use only belts installed or supplied by an authorized Mercedes Benz dealer e Do not pass belts over sharp edges e Do not make any modification that could change the effectiveness of the belts The SRS is designed to function on a one time only basis An airbag or emergency tensioning retractor ETR that was activated must be replaced No modifications of any kind may be made to any components or wiring of the SRS This includes the installation of additional trim material badges etc over the steering wheel hub or front passenger airbag cover and installation of additional electrical electronic equipment on or near SRS components and wiring Several airbag system components at the steering wheel get hot after the airbag has inflated Don t try to touch them Improper work on
64. eling abroad 89 Trunk lamp 96 Trunk lid Manual closing 118 Manual retraction of handle 118 Trunk separately locked 33 Turn signals 56 57 Vanity mirrors 62 Vehicle data card Vehicle jack 97 Vehicle tools 97 Warranty coverage 125 Washing the car 114 Wheels Alloy wheels 115 Rims and tires 98 Wheels changing 100 Windshield headlamp washer system Fluid level low 81 Washer fluid mixing ratio 57 Winter driving 89 Winter driving instructions 19 Wiper blades replacing 119 141 Service and Literature Your authorized Mercedes Benz dealer has trained technicians and original Mercedes Benz parts to service your vehicle properly For expert advice and quality service see your authorized Mercedes Benz dealer If you are interested in obtaining service literature for your vehicle please contact your authorized Mercedes Benz dealer We consider this to be the best way to obtain accurate information for your vehicle Warning To help avoid personal injury be extremely careful when performing any maintenance work or repairs Improper or incomplete service may damage the vehicle or its equipment which may in turn result in personal injury If you have any question about carrying out some service turn to the advice of an authorized Mercedes Benz dealer 142 Check Regularly and Before a Long Trip The engine compartment of model S 600 is illustrated 1 Fuel Supply To add fuel turn cap to the left
65. ep this in mind when checking tire pressure inside a garage especially in the winter Example If garage temperature approx 68 F 20 C and ambient temperature approx 32 F 0 C then the adjusted air pressure specified air pressure 3 psi 0 2 bar Tire pressures listed for light loads are minimum values offering high driving comfort Increased inflation pressures for heavy loads produce favorable handling characteristics with lighter loads and are perfectly permissible The ride of the vehicle however will become somewhat harder Tire temperature and pressure increase with the vehicle speed Tire pressure should therefore only be corrected on cold tires Correct tire pressure in warm tires only if pressure has dropped be low the pressure listed in the table and the respective operating conditions are taken into consideration An under inflated tire due to a slow leak e g due to a nail in the tire may cause damage such as tread separation bulging etc Regular tire pressure checks including the spare tire at intervals of no more than 14 days are therefore essential If a tire constantly loses air it should be inspected for damage Warning Do not over inflate tires Over inflating tires can result in sudden deflation blowout because they are more likely to become punctured or damaged by road debris potholes etc Follow recommended inflation pressures Do not overload the tire
66. ering lock position 0 to positions 1 or 2 malfunctions in the crash sensor are detected and indicated the SRS indicator lamp stays on longer than 4 seconds In the operational mode after the indicator lamp has gone out following the initial check interruptions and short circuits in the airbag ignition circuit and in the driver and passenger seat belt buckle harnesses and low voltage in the entire system are detected and indicated In the event a malfunction of the SRS is indicated as outlined above the SRS may not be operational We strongly recommend that you visit an authorized Mercedes Benz dealer immediately to have the system checked otherwise the SRS may not be activated when needed Important The airbags are designed to activate only in certain frontal and front angled impacts within the shaded area shown in the illustration on page 48 Only during these types of impacts will they provide their supplemental protection The driver and passenger should always wear the seat belts otherwise it is not possible for the airbags to provide their intended supplemental protection In cases of other frontal impacts roll overs certain side impacts rear collisions or other accidents without sufficient frontal forces the airbag will not be activated The driver and passengers will then be protected by the fastened seat belts We caution you not to rely on the presence of an airbag in order to
67. extend freely Cruise Control Any given speed above approximately 25 mph 40 km h can be maintained with the cruise control by operating the lever 1 Accelerate and set Lift lever briefly to set speed Hold lever up to accelerate 2 Decelerate and set Depress lever briefly to set speed Hold lever down to decelerate Normally the vehicle is accelerated to the desired speed with the accelerator Speed is set by briefly pushing the lever to position 1 or 2 The accelerator can be released The speed can be increased e g for passing by using the accelerator As soon as the accelerator is released the previously set speed will be resumed automatically If a set speed is to be increased or decreased slightly e g to adapt to the traffic flow hold lever in position 1 or 2 until the desired speed is reached or briefly tip the control lever in the appropriate direction for increases or decreases in 0 6 mph 1 km h increments When the lever is released the newly set speed remains 76 3 Canceling To cancel the cruise control briefly push lever to position 3 When you step on the brake or the vehicle speed drops below approx 25 mph 40 km h for example when driving upgrade the cruise control will be canceled If the cruise control cancels by itself and remains inoperative until the engine is restarted have the system checked at your authorized Mercedes Benz dealer as soon as possible 4 Res
68. he front seat For safety reasons avoid adjusting the seat or seat back into positions which could affect the correct seat belt position Unfastening of Seat Belts Push the release button 3 in the belt buckle 2 Allow the retractor to completely rewind the seat belt by guiding the latch plate 1 Notes Operation The inertia reel stops the belt from unwinding during sudden vehicle stops or when quickly pulling on the belt The locking function of the reel may be checked by quickly pulling out the belt 47 Warning USE SEAT BELTS PROPERLY Each occupant should wear their seat belt at all times because seat belts help reduce the likelihood of and potential severity of injuries in accidents including rollovers SRS driver airbag passenger airbag ETR seat belt emergency tensioning retractors and knee bolsters are designed to enhance the protection offered to properly belted occupants in certain frontal impacts which exceed preset deployment tresholds e Improperly positioned seat belts do not provide maximum protection and may cause serious injuries in case of an accident e Never wear the shoulder belt under your arm against your neck or off your shoulder In a crash your body would move too far forward That would increase the chance of head and neck injuries The belt would also apply top much force to the ribs which could severely injure internal organs such as your liver or s
69. hicle can be equipped with tether anchorages for a top tether strap Consult your authorized Mercedes Benz dealer for installation of these anchorages In compliance with Canadian Motor Vehicle Safety Standard 210 1 child restraint tether anchorage hardware is attached to the tool kit located in the trunk 54 Steering Lock 0 The key can be withdrawn in this position only The steering is locked with the key removed from the steering lock The key can be removed only with the selector lever in position P After removing the key or with the key in steering lock position 0 the selector lever is locked in position P 1 Steering is unlocked If necessary move steering wheel slightly to allow the key to be turned clockwise to position 1 Most electrical consumers can be operated For detailed information see respective subjects 2 Driving position 3 Starting position Refer to Index for Starting and turning off the engine Warning When leaving the vehicle always remove the key from the steering lock Do not leave children unattended in the vehicle Unsupervised use of vehicle equipment may cause serious personal injury Notes A warning will sound when the driver s door is opened with the key in steering lock position 1 or 0 With the engine at idle speed the charging rate of the alternator output is limited It is therefore recommended to turn off unnecessary electrical consumers while
70. hicle speed and engine temperature This allows the catalytic converter to heat up more quickly to operating temperatures During the brief warm up period this delayed upshift and increased engine noise might be perceived as a malfunction However neither the engine nor transmission are negatively affected by this mode of operation 74 The delayed up shift is effective with vehicle speeds below 31 mph 50 km h at partial throttle and engine temperatures below 95 F 35 C Do not exceed the vehicle speed limits for individual gear selections Overrevving the engine when selector lever is moved to a lower driving range could result in serious damage to the engine that is not covered by the Mercedes Benz Limited Warranty Refer to Technical Data for downshift points Warning On slippery road surfaces never downshift in order to obtain braking action This could result in rear wheel slip and reduced vehicle control Your vehicle s ABS will not prevent this type of loss of control This applies particularly for position To prevent the engine from laboring at low RPMs do not allow the engine speed to drop too low on uphill gradients Depending on the degree of the incline shift selector lever to a lower gear early enough to maintain engine RPM within the best torque range Maneuvering To maneuver in tight areas e g when pulling into parking space control the car speed by gradually releasing the brakes Acceler
71. ing clock more than one minute ahead or back Pull out adjustment knob 1 turn to the right respectively left and hold until the desired time is set Within the first 2 seconds the minute hand advances 8 minutes and advances another 8 minutes every additional second thereafter 69 Shelf below Rear Window Warning The shelf below the rear window should not be used to carry objects This will prevent such objects from being thrown about and injuring vehicle occupants during an accident or sudden Antenna The antenna extends when switching on the radio and or telephone Note To retract the antenna e g when entering a car wash both radio and telephone must be switched off Cellular Telephone The vehicle is prepared for the installation of a cellular telephone For further information and installation contact your authorized Mercedes Benz dealer Warning Some jurisdictions prohibit the driver from using a cellular telephone while driving a vehicle Whether or not prohibited for safety reasons the driver should not use the cellular telephone while the vehicle is in motion Stop the vehicle in a safe location before answering or placing a call 70 Driving 71 Drinking and Driving Warning Drinking and driving can be a very dangerous combination Even a small amount of alcohol or drugs can affect your reflexes perceptions and judgement The possibility of a serious or even fatal accident is
72. input signals to or receive output signals from the control module Malfunctions resulting from interruptions or failure of any of these components are indicated by the CHECK ENGINE mal function indicator lamp in the instrument cluster and are simul taneously stored in the SFI control module If the CHECK ENGINE malfunction indicator lamp comes on have the system checked at your authorized Mercedes Benz dealer as soon as possible An on board diagnostic connector with pushbutton and light emitting diode LED is located on the engine compartment firewall allowing the accurate identification of system malfunctions through the readout of diagnostic trouble codes 88 Traveling Abroad Abroad there is a widely spread Mercedes Benz service network at your disposal If you plan to travel into areas which are not listed in the index of your dealer directory you should request pertinent information from your authorized Mercedes Benz dealer Winter Driving Have your car winterized at your authorized Mercedes Benz dealer before the onset of winter e Change the engine oil if the engine contains an oil which is not approved for winter operation For viscosity SAE class and filling quantity see Capacities Fuels Coolants Lubricants etc in Index e Check engine coolant anticorrosion antifreeze concentration e Additive for the windshield washer and headlamp cleaning system Add MB Concentrate S to a premixed
73. it button Transmitter eye and battery check The vehicle can be centrally locked and unlocked as well as the windows and sliding roof closed with infrared remote control The transmitter is located in the key holder the receivers are located in the door handles and next to the trunk lock 3 Receiver in door handle Unlocking Aim transmitter eye 2 at a receiver 3 and press transmit button 1 Distance to receiver max 20 ft 6 m The green indicator lamps on the receivers should blink They stop blinking when the vehicle is unlocked Note If the trunk was previously locked separately it will remain locked see Index 29 Receiver next to trunk lock Locking Aim transmitter eye 2 at a receiver 3 and press transmit button 1 Distance to receiver max 20 ft 6 m The red indicator lamps on the receivers should blink They stop blinking after approximately 3 seconds when the vehicle is properly locked Notes If a door or the trunk is not properly closed after you attempt to lock the car by remote control the red indicator lamps will continue to blink max 10 seconds Open the door or trunk lid close it properly and lock the car again If the vehicle cannot be locked or unlocked by pressing the transmit button 1 then it may be necessary to change the batteries in the transmitter if ok battery indicator lamp in transmitter will light briefly when transmitting or to synchronize
74. ition only when the engine is idling and the service brake is applied Do not release the brake until ready to drive The vehicle may otherwise start creeping when the selector lever is in drive or reverse position Warning It is dangerous to shift the selector lever out of P or N if the engine speed is higher than idle speed If your foot is not on the brake pedal the car could accelerate quickly forward or in reverse You could lose control of the car and hit someone or something Only shift info gear when the engine is idling normally and when your right foot is firmly on the brake pedal Important After selecting any driving position from N or P wait a moment to allow the gear to fully engage before accelerating especially when the engine is cold Accelerator position Partial throttle early up shifting normal acceleration Full throttle later up shifting rapid acceleration Kick down depressing the accelerator beyond full throttle downshifting to next lowest gear maximum acceleration Once the desired speed is attained ease up on the accelerator the transmission shifts up again 173 Selector Lever Positions The automatic gear shifting process can be adapted to specific operating conditions using the selector lever P Parking lock The parking lock is an additional safeguard to the parking brake when parking the vehicle Engage only with the car stopped Note The key
75. jury during a collision or sudden maneuver exercise care when stowing things Put luggage or cargo in the trunk if possible Do not pile luggage or cargo higher than the seat backs Do not place anything on the shelf below the rear window 96 coll Vehicle Jack m u l LAN SET eT ese 1 papooid 3 1 Jack arm 2 Jack base See illustration for proper storage of jack Before storing the jack on the felt in the spare wheel well the jack arm 1 must be lowered almost to the base 2 of the jack Warning The jack is designed exclusively for jacking up the vehicle at the jack tubes built into either side of the vehicle Use the jack only to lift the vehicle during a wheel change Never get beneath the vehicle while it is supported by the jack Keep hands and feet away from the area under the lifted vehicle Always firmly set parking brake and block wheels before raising vehicle with jack Do not disengage parking brake while the vehicle is raised Be certain that the jack is always vertical when in use especially on hills Always try to use the jack on level surface Be sure that the jack arm is fully inserted in the jack tube Lower the vehicle onto sufficient capacity jack stands before working under the vehicle Vehicle Tools Storage Compartment below Tool Box 1 Lock tool box lid 2 Unlock tool box lid To open the storage compartment Lift out tool box To insert the tool box Positi
76. key removed or in steering lock position 0 The switch is illuminated when the exterior lamps are switched on except standing lamps Glass Sliding Roof with Rear Pop Up Feature An additional screen can be slid into the roof opening to guard against sun rays When sliding the roof open the screen will also retract Warning When closing the sliding roof be sure that there is no danger of anyone being harmed by the closing procedure Notes The sliding roof can be opened or closed manually should an electrical malfunction occur refer to Emergency Operation in Index The sliding roof can also be closed with the key or infrared remote control while locking the vehicle doors see Central Locking System in Index 66 in center console front Power Windows Switches for left front left rear right front right rear safety switch individual switches rear doors Ant WN in rear doors Turn key in steering lock to position l or2 Press switch in to resistance point to close to open Release switch when window is in desired position Express Opening and Closing Press switch Bd or past re sistance point and release window opens or closes completely Tg inte procedure briefly press gt ae If the upward movement of the window is blocked during the closing procedure the window will stop during the last few inches before closure and open slightly When pressing and ho
77. l not activate if the engine coolant temperature is below 122 F 50 C or if the battery charge level is insufficient To cancel e Press button indicator lamp goes out e Turn key in steering lock to position 2 The system will automatically shut off e after approx 30 minutes e ifthe engine coolant temperature drops below 122 F 50 C e ifthe battery voltage drops 7 Air Recirculation Outside air is not supplied to the car s interior This mode can be selected to prevent annoying odors or dust from entering the car s interior To select Press button indicator lamp lights up To cancel Press button indicator lamp goes out The system will automatically switch from aa ee air to fresh air if button is pressed e after approx 5 minutes at outside temperatures below approx 40 F 5 C e after approx 20 minutes at outside temperatures above approx 40 F 5 C If button is pressed after approx 5 minutes Notes If the windows should fog up from the inside switch from recirculated air back to fresh air At high outside temperatures the system automatically engages the recirculated air mode thereby increasing the cooling capacity performance switching to partially fresh air within 20 minutes 25 8 Air Volume Selector The air volume is automatically regulated in AUTO Normal setting and all intermediate positions except when selecting MIN minimum air flow
78. l stop or before a long trip See Index Engine Oil Consumption Engine oil consumption checks should only be made after the break in period During the break in period higher oil consumption may be noticed and is normal Frequent driving at high engine speeds results in increased consumption Fuel Consumption Gauge While driving current fuel consumption is indicated in miles per gallon mpg or in Canada liters per 100 kilometers 1 100 km With the engine switched off the needle reads 0 Due to system design maximum consumption is indicated at engine idle speed 79 Fuel Reserve Warning Lamp With the key in steering lock position 2 the fuel reserve warning lamps come on and should go out when the engine is running If the warning lamps do not go out after starting the engine or if they come on while driving it indicates that the fuel level is down to the reserve quantity of approx 3 3 gal 12 5 liters Outside Temperature Indicator The temperature sensor is located in the front bumper area Due to its location the sensor can be affected by road or engine heat during idling or slow driving This means that the accuracy of the displayed temperature can only be verified by comparison to a thermometer placed next to the sensor not by comparison to external displays e g bank signs etc Adaptation to ambient temperature takes place in steps and depends on the prevailing driving conditions
79. lamp blinks for a brief period to remind the driver and passengers to fasten seat belts before driving off Brake Pad Wear Indicator Lamp The brake pad wear indicator lamp in the instrument cluster comes on when the key in the steering lock is turned to position 2 and goes out when the engine is running If the indicator lamp lights up during braking this indicates that the front wheel brake pads are worn down Have the brake system checked at your authorized Mercedes Benz dealer as soon as possible 82 Brake Warning Lamp The brake warning lamp will come on with the key in steering lock position 2 and should go out when the engine is running The brake warning lamp will come on e when there is insufficient brake fluid in the reservoir engine running and parking brake released e when the parking brake is set engine running Warning Driving with the brake warning lamp on can result in an accident Have your brake system checked immediately if the brake warning lamp stays on Don t add brake fluid before checking the brake system Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire You can be seriously burned When the minimum mark on the reservoir is reached have the brake system checked for brake pad thickness and leaks To test the brake warning lamp turn key in steering lock to position 2 The brake warning lamp come
80. lding the switchegjto close the window and upward movement of the window is blocked during the last few inches before closure it will stop but not open slightly Blocking of Rear Door Window Operation If no operation of the rear windows by switch 6 for instance by children is desired slide safety switch 5 to right symbol EJ becomes visible 67 Warning When closing the windows be sure that there is no danger of anyone being harmed by the closing procedure In case of obstruction the automatic reversal will not operate if a window is being closed by pressing the switch to its resistance point and holding it there or when using a key or the remote control The closing procedure can be immediately reversed by either pressing the switch isg turning the key to the unlocking position or releasing and pressing the transmit button and holding it The power windows can also be closed with the key or infrared remote control while locking the vehicle doors see Central Locking System in Index Warning When leaving the vehicle always remove the key from the steering lock Do not leave children unattended in the vehicle Unsupervised use of vehicle equipment can cause serious personal injury Note If the side windows cannot be fully opened or closed automatically by pressing the button past the point of resistance e g after ma battery change press down side of power window switch until the win
81. lts Position shoulder belt across chest and shoulder not face or neck A booster seat may be necessary to achieve proper belt positioning Adjust the front passenger seat as far as possible rearward from the dashboard when a child restraint is installed Supplemental Restraint System SRS The SRS uses two crash severity levels thresholds to activate either the ETR or airbag or both Activation depends on exceeding the thresholds and fastening of the seat belt Seat belt fastened e first threshold exceeded ETR activates e second threshold exceeded airbag also activates Seat belt not fastened e first threshold exceeded airbag activates but not ETR Driver and front passenger systems operate independently from each other Emergency Tensioning Retractor ETR The seat belts for the front seats are equipped with emergency tensioning retractors These tensioning retractors are located in each belt s inertia reel and become operationally ready with the key in steering lock position 1 or 2 The emergency tensioning retractors are designed to activate only when the seat belts are fastened during frontal and front angled impacts exceeding the first threshold of the SRS They remove slack from the belts in such a way that the seat belts fit more snugly against the body restricting its forward movement as much as possible In cases of other frontal impacts roll overs certain side impacts rear collisions or
82. lugs Approved spark plugs refer to Technical Data Bulbs High and low beams HB2 60 55 W fog lamps YC H3 55 W turn signal standing side marker and parking lamps front 2357 NA 28 5 8 3 W 30 2 2 cp tail parking standing and driver s side rear fog lamp 21 4 W 35 1 2 cp turn signal lamps rear 21 W 32 cp tail and parking lamps 5 W stop lamps 21 W 32 cp high mounted stop lamp H2 20 W license plate lamps 5 W Tire Pressure For tire pressure refer to tire pressure inside the fuel filler flap Air Conditioner R 134a refrigerant and special lubricant refer to Technical Data also see Index 144
83. lus additional cosolvents Using mixtures of Ethanol and Methanol is not allowed Gasohol which contains 10 Ethanol and 90 unleaded gasoline can be used These blends must also meet all other fuel requirements such as resistance to spark knock boiling range vapor pressure etc Gasoline Additives A major concern among engine manufacturers is carbon build up caused by gasoline Mercedes Benz recommends to use only quality gasoline containing additives that prevent the build up of carbon deposits After an extended period of using fuels without such additives carbon deposits can build up especially on the intake valves and in the combustion area leading to engine performance problems such as warm up hesitation unstable idle knocking pinging misfire power loss Do not blend other specific fuel additives with fuel They only result in unnecessary cost and may be harmful to the engine operation Damage or malfunctions resulting from poor fuel quality are not covered by the Mercedes Benz Limited Warranty 133 Coolants The engine coolant is a mixture of water and anticorrosion anti freeze which provides corrosion protection e freeze protection e boiling protection by increasing the boiling point The cooling system was filled at the factory with a coolant providing freeze protection to approx 22 F 30 C and corrosion protection The coolant solution must be used year round t
84. m also locks or unlocks the fuel filler flap Note If the fuel filler flap cannot be opened refer to Fuel Filler Flap Manual Release see Index Doors Opening pull handle Unlocking Locking Individual door from inside hWN e Push lock button down to lock e Pull lock button up to unlock Central locking switch When you lock the car all door lock buttons should move down If any one stays up the respective door is not properly closed You should then unlock the car open and reclose this door and lock the car again Each individual door can be locked with door lock button the driver s door can only be locked when it is closed 32 The doors can only be locked with the central locking switch if the front doors are closed The doors cannot be unlocked with the central locking switch if car was previously locked from outside When opening a front door the entire car is unlocked if it was previously locked with the central locking switch If the car has previously been locked from the outside only the door being opened from the inside will unlock the remaining doors the trunk lid and fuel filler flap remain locked Trunk Neutral position push to open Unlocking Locking detent Separate locking of trunk remove key in this position hRWONe When the trunk is separately locked it remains locked when unlocking any door To deny any unauthorized person acces
85. mbination switch to wiper setting II Have the system checked at your authorized Mercedes Benz dealer as soon as possible Signaling Turns with Hazard Flasher in Use For example when the vehicle is being towed key in steering lock turned to position 2 With hazard flasher on activate combination switch for left or right turn signal only the selected turn signal will blink Upon canceling the turn signal the hazard flasher will operate again Turn Signal Failure If one of the turn signals fails the turn signal indicator system flashes and sounds at a faster than normal rate In addition the exterior lamp failure indicator will come on 57 Exterior Lamp Switch Canada only When the engine is running the low beam includes parking lamps side marker lamps tail lamps license plate lamps and instrument panel lamps are automatically switched on Note For nighttime driving the exterior lamp switch should be turned to position 22 to permit activation of the high beam headlamps wn gQ A E off Parking lamps also side marker lamps taillamps license plate lamps instrument panel lamps Canada only When the engine is running the low beam is additionally switched on Parking lamps plus low beam or high beam headlamps combination switch pushed forward Standing lamps right turn left one stop Standing lamps left turn left two stops Fog lamps pull out one stop with
86. me caution when opening the hood if there are any signs of steam or coolant leaking from the cooling system Do not remove pressure cap on coolant reservoir if engine temperature is above 194 F 90 C Allow engine to cool down before removing cap The coolant reservoir contains hot fluid and is under pressure Using a rag turn cap to first notch to relieve excess pressure If opened immediately scalding hot fluid and steam will be blown out under pressure possibly causing personal injury Do not spill antifreeze on hot engine parts Antifreeze contains ethylene glycol which may burn if it comes into contact with hot engine parts You can be seriously burned Adding Coolant If coolant has to be added a 50 50 mixture of water and MB anticorrosion antifreeze should be added The drain plugs for the cooling system are located on the right and left sides of the engine block and at the bottom of the radiator Anticorrosion antifreeze see Coolants in Index 93 S 500 Checking Engine Oil Level 1 Oil dipstick 2 Oil filler cap To check the engine oil level park vehicle on level ground with engine at normal operational temperature Add oil if needed only to the upper mark max Do not overfill engine PD1 0078 Be4 For viscosity and capacity see Capacities Fuels Coolants Lubricants etc in Index For low engine oil level warning lamp see Index S 600 Check engine oil level
87. mp 58 108 Taillamps 58 108 114 Layout of poly V belt drive 121 Lighter 65 Low engine oil Level warning lamp 79 Lumbar support 40 Maintenance 4 8 Memory 38 Mirrors adjusting 59 60 Multicontour backrest 40 Outside temperature indicator 80 Parking brake 15 18 65 72 75 83 85 95 97 100 110 Power closing assist for doors and trunk lid 35 Power seats 37 Power windows 67 Problems with your vehicle 136 Reading lamps 63 Rear fender indicators 76 Rear passenger compartment adjustable air outlet 27 Rear seat cushion 118 Rear view mirrors Exterior rear view mirrors 60 Inside rear view mirror 38 39 44 59 61 Rear window defroster 69 Rear window sunshade 68 Remote control infrared 29 116 Replacing bulbs 106 Roadside assistance 5 Roof rack 122 140 Safety guidelines for the seat belt emergency tensioning retractor and airbag 53 Seat belt warning lamp 82 Seat belts and warning system 45 Shelf below rear window 70 Sliding roof Emergency operation 120 Sliding roof operation 66 Snow chains 86 89 Spare parts service 122 Spare wheel 96 SRS malfunction 50 Starting and turning off the engine 15 Steering lock 55 Steering wheel adjustable 44 Storage compartments 64 Stowing things in the vehicle 96 Sun visors 62 Supplemental restraint system SRS 45 49 Technical data 126 Tire inflation pressure 103 Tires 17 18 85 89 98 99 103 126 128 135 Towing the vehicle 112 Trav
88. n off engine immediately and contact an authorized Mercedes Benz dealer Do not operate the car until the condition is repaired There is no need for concern should the oil pressure warning lamp light up briefly for example in sharp turns or hard braking provided the lamp goes out immediately We recommend you to drive to the nearest service station where the engine oil should be topped to the full mark on the dipstick with an approved oil 78 Low Engine Oil Level Warning Lamp With the key in steering lock position 2 the oil level warning lamp comes on and should go out when the engine is running If the warning lamp comes on with the engine running and at operating temperature the engine oil level has dropped to approximately the minimum mark on the dipstick When this occurs the warning lamp will first come on intermittently and then stay on if the oil level drops further If no oil leaks are noted and there is no loss in engine oil pressure continue to drive to the nearest service station where the engine oil should be topped to the full mark on the dipstick with an approved oil The low engine oil level warning light should not be ignored Extended driving with the light illuminated could result in engine damage that is not covered by the Mercedes Benz Limited Warranty In addition to the warning lamp the engine oil level should be periodically checked with the dipstick for example during a fue
89. n using any infant or child restraint system be sure to carefully read and follow all manufacturer s instructions for installation and use Warning According to accident statistics children are safer when properly restrained in the rear seating positions than in the front seating positions Rear facing child restraints must not be used in the front passenger seat They could be struck by the airbag when it inflates in a crash If this happens a child in the restraint could be seriously injured Infants and small children should never be held on the lap while the vehicle is in motion During an accident they would be almost impossible to hold and could be crushed between the adult and the dashboard Infants and small children should never share a seat belt with another occupant During an accident they could be crushed between the occupant and seat belt Children too big for child restraint systems should ride in rear seats using regular seat belts Position shoulder belt across chest and shoulder not face or neck A booster seat may be necessary to achieve proper belt positioning When the child restraint is not in use remove it from the car or secure it with the seat belt to prevent the child restraint from becoming a projectile in the event of an accident U S A Models only Since 1986 all U S child restraints comply with U S regulations without the use of a tether strap Canada Models only This ve
90. nstrument Cluster SAA M bh WON Fuel gauge with reserve warning lamp yellow See Index Index Coolant temperature gauge See Index Fuel consumption gauge See Index Engine oil pressure gauge bar with warning lamp red See Index Left turn signal indicator lamp green Knob for instrument lamps and trip odometer See Index Speedometer ASR function indicator lamp yellow See Index 9 10 11 13 14 15 16 54066 Bada Trip odometer Main odometer Outside temperature indicator See Index Right turn signal indicator lamp green Knob for setting clock to adjust pull knob out Tachometer Red marking on tachometer Excessive engine Clock See Index 12 Indicator Lamp Symbols Function Indicator Lamp High beam Warning Lamps should go out with the engine running unless Battery not being charged properly See Index Fluid level for windshield and headlamp washer system low See Index Coolant level low See Index Engine oil level low See Index Exterior lamp failure See Index ADS malfunction See Index ASR malfunction See Index i B B E a BRAKE R CHECK ENGINE Ww A i f TA ABS malfunction Brake pads worn down See Index Brake fluid low except Canada Parking brake engaged See Index Brake fluid low Canada only Parking brake engaged See Index SRS malfunction See Index Fasten seat belts See Index Engine malfunction California only If th
91. o Thoroughly spray the car with a diffused jet of water Direct only a very weak spray towards the ventilation intake Use plenty of water and rinse the sponge and chamois frequently Rinse with clear water and thoroughly wipe dry with a chamois Do not allow cleaning agents to dry on the finish Before running the vehicle through an automatic car wash fold back the outside mirrors to prevent them from getting damaged If the vehicle has been run through an automatic car wash in particular one of the older installations rewipe the reces sed sections in the tail lamps designed to prevent soiling if necessary No solvents fuels thinners etc must be used In the winter thoroughly remove all traces of road salt as soon as possible When washing the underbody do not forget to clean the inner sides of the wheels Tar Stains Quickly remove tar stains before they dry and become more difficult to remove MB Tar Remover is recommended Headlamp Cleaning System The condition of the wiper blades is important for satisfactory cleaning of the headlamp lenses We therefore recommend that the blades be inspected regularly Replace damaged wiper blades Window Cleaning Use a window cleaning solution on very dirty or oil stained windows Wiper Blades Clean the wiper blade rubber with a clean cloth and detergent solution Replace blades twice a year once before and once after winter Plastic Parts Headline
92. o position P and turn off engine Prevent vehicle from rolling away by blocking wheels with wheel chocks not supplied with vehicle or sizable wood block or stone When changing a wheel on a hill place chocks on the downhill side blocking both wheels of the other axle On a level road place one chock in front of and one behind the wheel that is diagonally opposite to the wheel being changed 4 Unfold wrench loosen but do not yet remove the wheel bolts 100 F40 0008 E13 Pad DOF ita 5 Remove the protective cover from the jack support tube opening by inserting a screwdriver in the opening and prying it out The tube openings are located directly behind the front wheel housings and in front of the rear wheel housings Insert jack arm fully into the tube hole up to the stop Place jack on firm ground Position the jack so that it is always vertical plumb line as seen from the side see arrow even if the vehicle is parked on an incline Jack up the vehicle until the wheel is clear of the ground Never start engine while vehicle is raised Unscrew wheel bolts completely Keep bolt threads protected from dirt and sand While removing the last bolt hold wheel against hub to avoid paint damage on rim Remove wheel Grip wheel from the sides Keep hands from beneath the wheels 10 Screw the alignment bolt 1 supplied in the tool kit into the upper most threaded hole Warning
93. o provide the necessary corrosion protection and increase in the boil over protection You should have it replaced every 3 years To provide the important corrosion protection the solution must be at least 45 anticorrosion antifreeze equals a freeze protection to approx 22 F 30 C If you use a solution that is more than 55 anticorrosion antifreeze freeze protection to approx 49 F 45 C the engine temperature will increase due to the lower heat transfer capability of the solution Therefore do not use more than this amount of anti corrosion antifreeze If the coolant level is low water and MB anticorrosion antifreeze should be used to bring it up to the proper level have cooling system checked for signs of leakage The water in the cooling system must meet minimum requirements which are usually satisfied by normal drinking water If you are not sure about the water quality consult your authorized Mercedes Benz dealer Anticorrosion antifreeze Your vehicle contains a number of aluminum parts The use of aluminum components in motor vehicle engines necessitates that anticorrosion antifreeze coolant used in such engines be specifically formulated to protect the aluminum parts Failure to use such anticorrosion antifreeze coolant will result in a significantly shortened service life Therefore the following product is strongly recommended for use in your car Mercedes Benz Anticorrosion Antifreeze
94. on rear end of tool box press down its front end 97 OERD Wheels 1 Wheel bolt for 7 J x 16 H 2 wheel rim 2 Wheel bolt for 8 J x 16 H 2 wheel rim Replace rims or tires with the same designation manufacturer and type as shown on the original part See your authorized Mercedes Benz dealer for further information Important The spare wheel rim size is 7 hJx16H2 In the case of a flat tire or breakdown you may temporarily use a 7 2 J x 16 H 2 instead of the 8 J x 16 H 2 wheel rim on the rear axle when observing the following restrictions e Use only the wheel bolts supplied in the vehicle tool kit e Do not exceed vehicle speed of 50 mph 80 km h e Drive to the nearest repair facility For additional information refer to Technical Data Warning Do not mix different tire con struction types i e radial bias and bias belted on your car because handling may be adversely affected and may result in loss of control See your authorized Mercedes Benz dealer for information on tested and recommended rims and tires for summer and winter operation They can also offer advice concerning tire service and purchase Tire Replacement Front tires should be replaced in sets Furthermore in the event of tire replacement the spare wheel if possible should be used on the rear axle Rims and tires must be of the same size and type For dimensions see Technical Data We recommend tha
95. oors are opened Spare Parts Service All authorized Mercedes Benz dealers maintain a stock of original spare parts required for maintenance and repair work In addition strategically located parts distribution centers provide quick and reliable parts service More than 300 000 different spare parts even for older models are available Mercedes Benz original spare parts are subjected to the most stringent quality inspections Each part has been specifically developed manufactured or selected for and adapted to Mercedes Benz vehicles Therefore Mercedes Benz original spare parts should be installed 122 Technical Data 123 Identification Plates When ordering spare parts please specify vehicle Identification and engine numbers AAS Certification Tag left door pillar Identification Tag lower edge of windshield Vehicle Identification No on cross member beneath front passenger seat Engine No S 320 only front right Body No and Paintwork No Emission Control Tag Information Tag California version Vacuum line routing for emission control system 124 POH 0001 B1Z Vehicle Data Card The vehicle data card contains all important data pertaining to the vehicle It should be kept in the maintenance booklet where indicated and it is needed when obtaining replacement or additional keys at your authorized Mercedes Benz dealer Warranty Coverage
96. or and inside rear view mirrors can be programmed into memory by pushing first button F and then 2 respectively 3 Note See Index for instructions on adjustment of steering wheel and mirrors Recalling seat head restraint steering wheel exterior and inside rear view mirror positions stored in memory To recall a seat head restraint steering wheel exterior and inside rear view mirror position push and hold position button 1 2 or 3 until seat head restraint steering wheel exterior and inside rear view mirror movement has stopped The seat head restraint steering wheel exterior and inside rear view mirror movement stops when the position button is released Caution Do not remove head restraints except when mounting seat covers For removal and installation refer to Head Restraints Removal in Index Whenever restraints have been removed be sure to reinstall them before driving 38 Important Bring seat backrest to upright position before recalling a stored seat head restraint steering wheel exterior and inside rear view mirror position otherwise the front seats could get forced against a rear seat and be damaged Prior to operating the vehicle the driver should adjust the seat height for proper vision as well as fore aft placement and seat back angle to insure adequate control reach operation and comfort The head restraint should also be adjusted for proper height Both the inside and
97. oring Mirror Positions in Memory The exterior and inside rear view mirror positions are stored in memory with the seat head restraint steering column position and can be recalled when necessary see Index Note If the inside rear view mirror was adjusted separately the originally stored position remains in memory To recall position press the desired position button Folding the mirrors in Turn switch to point rearward Press switch rearward until the mirrors are folded in Important Before running the vehicle through an automatic car wash fold mirror in otherwise they may get damaged Folding the mirrors out Turn switch to point rearward Press switch forward until the mirrors are folded out Important Do not fold mirrors out forcing them by hand This will damage the operating mechanism of the mirrors 61 Sun Visors Swing sun visors down to protect against sun glare If sunlight enters through a side window disengage visor from inner mounting and pivot to the side From this position the visor can slide forward and backward on its shaft Illuminated Vanity Mirrors Front seats With the visor engaged in its inner mounting the lamp can be switched on by opening the cover Warning Do not use the vanity mirror while driving 62 Interior Lighting 1 Interior Lamps Door contact ee A Interior lamps are switched on and off delayed when unlocking or lo
98. ound and the selector lever in position N for distances up to 30 miles 50 km and at a speed not to exceed 30 mph 50 km h To positively avoid a possibility of damage to the transmission however we recommend to disconnect the drive shaft at the rear axle drive flange on any towing beyond a short tow to a nearby garage Do not tow with sling type equipment Towing with sling type equipment over bumpy roads will damage radiator and supports Use wheel lift or flat bed equipment Warning With the engine not running there is no power assistance for the braking and steering systems In this case it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle Note To signal turns while being towed with hazard flasher in use turn key in steering lock to position 2 and activate combination switch for left or right turn signal in usual manner only the selected turn signal will operate Upon canceling the turn signal the hazard flasher will operate again Vehicles with Acceleration Slip Control ASR Caution If the vehicle is towed with the front axle raised the key must not be in steering lock position 2 Otherwise the acceleration slip control will immediately be engaged and will apply the rear wheel brakes 112 Cleaning and Care of the Vehicle Warning Many cleaning products can be hazardous Some are poisonous others are flammable Alw
99. our safety and that of your passengers we ask you to make a small investment of your time e Please read this manual carefully before putting it aside Then return it to your vehicle where it will be handy for your reference e Please abide by the recommendations contained in this manual They are designed to acquaint you with the operation of your Mercedes Benz e Please abide by the warnings and cautions contained in this manual They are designed to help improve the safety of the vehicle operator and occupants We extend our best wishes for many miles of safe pleasurable driving DaimlerChrysler AG Operator s manual This Operator s Manual contains a great deal of useful information We urge you to read it carefully and familiarize yourself with the vehicle before driving For your own safety and longer service life of the vehicle we urge you to follow the instructions and warnings contained in this manual Ignoring them could result in damage to the vehicle or personal injury to you or others Vehicle damage caused by failure to follow instructions is not covered by the Mercedes Benz Limited Warranty Your vehicle may have some or all of the equipment described in this manual Therefore you may find explanations for optional equipment not installed in your vehicle If you have any questions about the operation of any equipment your authorized Mercedes Benz Center will be glad to demonstrate the proper procedures Owner s Service
100. outside rear view mirrors should be adjusted for adequate rearward vision Fasten seat belts Infants and small children should be seated in a properly secured restraint system that complies with U S Federal Motor Vehicle Safety Standard 213 and Canadian Motor Vehicle Safety Standard 213 1 All seat head restraint and rear view mirror adjustments as well as fastening of seat belts should be done before the vehicle is put into motion Backrest lock 1 Release button When a door is open the backrests can be folded forward without pushing the button With doors closed and key in steering lock position 2 the backrests are locked The lock can be released by pushing button 1 Entering Rear Passenger Compartment With the door open fold front seat backrest forward Automatically the seat will slide forward and the head restraint move down When folding the seat backrest back seat and head restraint return to their previous positions To interrupt the automatic process activate the power seat switch Warning Never place hands under seat or near any moving parts during the seat adjustment procedure 39 P ga Lumbar Support 1 Pressure regulator The seats have an inflatable air cushion built into the backrest to provide additional lumbar support The inflation pressure of the air cushion can be continuously varied between position 0 without pressure and position 5 maximum press
101. peed 77 Charge Indicator Lamp Should the charge indicator lamp fail to come on prior to starting when the key is in steering lock position 2 or should it fail to go out after starting or come while the engine is running this indicates a fault which must be repaired at an authorized Mercedes Benz dealer immediately If the charge indicator lamp comes on while the engine is running this may indicate that the poly V belt has broken Should this condition occur the poly V belt must be replaced before continuing to operate the vehicle Otherwise the engine will overheat due to an inoperative water pump which may result in damage to the engine Do not continue to drive the vehicle with the charge indicator lamp illuminated Doing so could result in engine damage that is not covered by the Mercedes Benz Limited Warranty Oil Pressure Gauge with Oil Pressure Warning Lamp With the key in steering lock position 2 the oil pressure warning lamp comes on and should go out when the engine is running The oil pressure at idle speed may drop if the engine is at operating temperature This will not jeopardize the engine s operational reliability Pressure must however rise immediately upon acceleration Note If the oil pressure warning lamp does not go out after starting the engine or comes on while driving and the oil pressure gauge needle drops to 0 then damage to the engine may occur with continued operation Tur
102. pleen Position the lap belt as low as possible on your hips and not across the abdomen If the belt is positioned across your abdomen it could cause serious injuries in a crash Each seat belt should never be used for more than one person at a time Do not fasten a seat belt around a person and objects Belts should not be worn twisted In a crash you wouldn t have the full width of the belt to take impact forces The twisted belt against your body could cause injuries e Pregnant women should also use a lap shoulder belt The lap belt portion should be positioned as low as possible on the hips to avoid any possible pressure on the abdomen USE CHILD RESTRAINTS PROPERLY e Infants and small children must be seated in an infant or child restraint system which is properly secured by a lap belt or lap belt portion of a lap shoulder belt Children could be endangered in an accident if their child restraints are not properly secured in the vehicle e Rear facing child restraints must not be used in the front seat with a passenger side airbag They could be struck by the airbag when it inflates in a crash If this happens a child in the restraint could be seriously injured 48 According to accident statistics children are safer when properly restrained in the rear seating positions than in the front seating positions Children too big for child restraint systems should ride in rear seats using regular seat be
103. practices and differences in road characteristics and climate Traction A B Ign The traction grades from highest to lowest are A B and C and they represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance Warning The traction grade assigned to this tire is based on braking straight ahead traction tests and does not include cornering turning traction Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive tempera ture can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law Warning The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause ex
104. r and Rubber Parts Do not use oil or wax on these parts See separate subject for additional information Seat Belts The webbing must not be treated with chemical cleaning agents Use only clear lukewarm water and soap Do not dry the webbing at temperatures above 176 F 80 C or in direct sunlight Warning Do not bleach or dye seat belts as this may severely weaken them In a crash they may not be able to provide adequate protection 114 Instrument Cluster Use a gentle dish washing detergent or mild detergent for delicate fabrics as a washing solution Wipe with a cloth moistened in lukewarm solution Do not use scouring agents Steering Wheel and Gear Selector Lever Wipe with a damp cloth and dry thoroughly or clean with MB Leather Cleaner Hard Plastic Trim Items Pour MB Plastic Cleaner onto soft lint free cloth and apply with light pressure Headliner and Shelf below Rear Window Clean with soft bristle brush or use a dry shampoo cleaner in case of excessive dirt Leather Upholstery Using aftermarket seat covers or wearing clothing that have the tendency to give off coloring e g when wet etc may cause the upholstery to become permanently discolored By lining the seats with a proper intermediate cover contact discoloration will be prevented Wipe leather upholstery with a damp cloth and dry thoroughly or clean with MB Leather Cleaner Exercise particular care when cleaning perforate
105. reached its normal operating temperature of 176 F 80 C or its temperature is 86 F 30 C Important The fluid level must not exceed the dipstick maximum mark Drain or siphon excess fluid if required Then push dipstick all the way in and swing locking lever downward 3 Note Damage to transmission caused by contamination of transmission fluid or overfilling of transmission may result in serious transmission damage which is not covered by the Mercedes Benz Limited Warranty 95 EEUE A EACLE AE TEAL ALAR TE EAE P5a 0070 B13 Trunk Lamp 1 Switching off 2 Switching on Switch off trunk lamp if the trunk is to remain open for along period of time This prevents the vehicle battery from being discharged The lamp switches on automatically when you open the trunk again the next time When you switch off the trunk lamp the trunk lid handle will also retract To close the trunk lid by its handle first switch on the trunk lamp Spare Wheel Lug Wrench 1 Trunk floor 2 Strap 3 Luggage bowl 4 Lug wrench Roll back the floor mat Lift the trunk floor 1 and engage strap 2 in the eyelet on the edge of the trunk lid To remove the spare tire turn luggage bowl 3 to the left and remove Pab t0e4 819 First Aid Kit 1 Opening lid The first aid kit is stored in the shelf below the rear window Stowing Things in the Vehicle Warning To help avoid personal in
106. rection of vehicle forward movement Note Thoroughly clean the inner side of the wheels any time you rotate the wheels or wash the vehicle underside The use of retread tires is not recommended Retread tires may adversely affect the handling characteristics and safety of the vehicle Dented or bent rims can cause tire pressure loss and damage to the tire beads For this reason check rims for damage at regular intervals The rim flanges must be checked for wear before a tire is mounted Remove burrs if any 99 Warning Changing Wheels The jack is designed exclusively for Move vehicle to a level area which is a jacking up the vehicle at the jack safe distance from the roadway tubes built into either side of the vehicle Use the jack only to lift the 1 vehicle during a wheel change Never get beneath the vehicle while it is supported by the jack Keep hands 2 and feet away from the area under the lifted vehicle Always firmly set parking brake and block wheels 3 before raising vehicle with jack Do not disengage parking brake while the vehicle is raised Be certain that the jack is always vertical when in use especially on hills Always try to use the jack on level surface Be sure that the jack arm is fully inserted in the jack tube Lower the vehicle onto sufficient capacity jack stands before working under the vehicle Set parking brake and turn on hazard warning flasher Move selector lever t
107. s armed Now the engine cannot be started The anti theft alarm is disarmed when unlocking either front door or the trunk with any of your vehicle s keys or infrared remote control Operation Once the alarm system has been armed the exterior vehicle lamps will flash and the horn will sound intermittently when someone opens a door opens the trunk opens the hood e removes the radio e switches on or bridges the ignition circuit e steps on the brake pedal The alarm will last approximately 150 seconds in the form of blinking exterior lamps At the same time an additional horn will sound intermittently for 60 seconds pause for 30 seconds and repeat for another 60 seconds The alarm will stay on even if the activating element a door for example is immediately closed Note Do not give the master key to an unauthorized person We recommend that you carry the flat key safely with you so that it is always handy The flat key has the same functions as the master key 36 P91 0023 613 The slide switches are located in each front door Turn key in steering lock to position 1 or 2 with the driver s or front passenger s door open the power seats can also be operated with the key removed or in steering lock position 0 Seat and head restraint adjustment A Seat fore aft up down B Seat tilt C Seat cushion depth D Backrest tilt E Head restraint Adjust head restraint to support the b
108. s by exceeding the specified vehicle capacity weight as indicated by the label on the driver s door latch post Overloading the tires can overheat them possibly causing a blowout 103 Battery The maintenance free battery is located in the trunk under the right hand wheel well cover panel The service life of the battery is dependent on its condition of charge The battery should always be kept sufficiently charged in order to last an optimum length of time Therefore we strongly recommend that you have the battery charge checked frequently and corrected if necessary especially if you use the vehicle less than approximately 200 miles 300 km per month mostly for short distance trips or if it is not used for long periods of time Only charge a battery with a battery charger after the battery has been disconnected from the vehicle electrical circuit When removing and connecting the battery always make sure that all electrical consumers are off and the key is in steering lock position 0 While the engine is running the battery terminal clamps must not be loosened or detached otherwise the alternator and other electronic components would be damaged Battery Recycling Batteries contain materials that can harm the environment with improper disposal Large 12 Volt storage batteries contain lead and smaller watch type batteries such as in the Infrared Remote Control Unit may contain mercury Recycling
109. s must match Therefore use only brands tested and recommended by us Inquire at your authorized Mercedes Benz dealer Engine with oil filter Automatic transmission Rear axle Model S 500 S 600 Capacity 8 5 US qt 8 0 1 10 7 US qt 10 0 1 Initial fill 9 1 US qt 8 6 1 Fluid change 8 1 US qt 7 7 1 1 5 US qt 1 41 Fuels coolants lubricants etc Recommended engine oils Automatic transmission fluid Hypoid gear oil SAE 90 85 W 90 Hydraulic system for adaptive dumping System ADS approx 2 1 US qt 2 0 1 MB Hydraulic fluid Power steering approx 1 4 US qt 1 3 D MB Power steering fluid Front wheel hubs approx 2 1 oz 60 g each High temperature roller bearing grease Accelerator control Hydraulic fluid Brake system approx 0 7 US qt 0 5 1 MB Brake fluid DOT 4 130 Model Capacity Fuels coolants lubricants etc Windshield washer and headlamp cleaning system approx 5 3 US qt 5 0 1 S 500 Cooling system S 600 Fuel tank including a reserve of Air conditioner system approx 15 3 US qt 14 5 D approx 16 4 US qt 15 5 1 approx 26 4 US qt 100 1 approx 3 3 US qt 12 5 1 MB Windshield washer concentrate S MB Anticorrosion antifreeze Premium unleaded gasoline Posted Octane 91 Avg of 96 RON 86 MON R 134a refrigerant and special lubricant Never R 12 1 Use MB Windshield Washer Concentra
110. s on and should go out when the engine is running 83 Antilock Brake System ABS The ABS prevents the wheels from locking up above a vehicle speed of approximately 2 mph 3 km h independent of road surface conditions It is necessary however that the vehicle speed reaches at least 5 mph 8 km h before commencing to brake At the instant one of the wheels is about to lock up a slight pulsation can be felt in the brake pedal indicating that the ABS is in the regulating mode On slippery road surfaces the ABS will respond even with only slight brake pedal pressure The pulsating brake pedal can be an indication of hazardous road conditions and functions as a reminder to take extra care while driving The ABS warning lamp in the instrument cluster comes on with the key in steering lock position 2 and should go out when the engine is running If the charging voltage falls below 10 volts the warning lamp comes on and the ABS is switched off When the voltage is above this value again the warning lamp should go out and the ABS will be operational If the ABS warning lamp does not go out or comes on while driving it indicates that the ABS has detected a malfunction and has switched off In this case the brake system functions in the usual manner but without antilock assistance Have the system checked at your authorized Mercedes Benz dealer as soon as possible Warning Even the ABS cannot prevent th
111. s to the trunk lock it separately Leave only the valet key with the vehicle Notes In case of a malfunction in the central locking system the doors and trunk can be locked and unlocked individually To lock turn key to position 3 or push down lock buttons To unlock turn key to position 2 or pull up lock buttons The trunk lid can be lowered by using the recessed grips in the trunk lid liner and closed with the dirt free retracting handle If the trunk lid cannot be closed refer to Trunk Lid Manual Closing see Index 33 eet 78 0022613 Door lock left and trunk lock Power Windows and Sliding Pop Up Roof 1 Closing 2 Interrupting 3 Opening So a Door lock right When locking doors or trunk turn key in door lock or trunk lock to position 1 and hold The windows and the sliding pop up roof begin to close automatically after approximately 1 second To interrupt the closing procedure turn key to position 2 Warning Never close the windows or sliding pop up roof if there is the possibility of anyone being harmed by the closing procedure In case the closing procedure causes potential danger the closing procedure can be immediately reversed by turning the key to the unlocking position 3 within 10 seconds The sliding pop up roof and windows will open again The sliding pop up roof will only open if it was not fully closed Note If the closing procedure is interrupted
112. ssary to lift the hood up slightly Caution To avoid damage to the windshield wipers or hood open the hood only with wipers in the parked position ee PRA DOGG 11 Pull handle 2 completely out of radiator grill and open hood do not pull up on handle To close Lower hood and let it drop into lock from a height of approx 1 ft 30 cm assisting with flat hands placed only on edges of hood 3 To avoid hood damage if hood is not fully closed repeat closing procedure Warning To help prevent personal injury stay clear of moving parts when the hood is open and the engine is running Be sure the hood is properly closed before driving The engine is equipped with a transistorized ignition system Because of the high voltage it is dangerous to touch any components ignition coil distributor spark plug sockets ignition cables diagnostic socket of the ignition system e with the engine running e while starting the engine e if the ignition is on and the engine is turned manually We recommend that you do not open the hood if you see flames or smoke coming from the engine compartment 92 Coolant reservoir of S 600 shown Checking Coolant Level To check the coolant level the vehicle must be parked on level ground and the engine stopped Check coolant level only when coolant is cold The coolant should reach the marking inside the filler neck Warning Use extre
113. stop and go or moderate constant driving and amount of temperature change Warning The outside temperature indicator is not designed to serve as an Ice Warning Device and is therefore un suitable for that purpose Indicated temperatures just above the freezing point do not guarantee that the road surface is free of ice Coolant Temperature Gauge If the antifreeze mixture is effective to 22 F 30 C the boiling point of the coolant in the pressurized cooling system of your vehicle is approx 266 F 130 C During severe operating conditions and stop and go city traffic the coolant temperature may rise close to the red marking The engine should not be operated with the coolant temperature in the red zone Doing so may cause serious engine damage which is not covered by the Mercedes Benz Limited Warranty Warning Driving when your engine is badly overheated can cause some fluids which may have leaked into the engine compartment to catch fire You could be seriously burned Turn off the engine and get out of the car until it cools down Steam from an overheated engine can cause serious burns and can occur just by opening the engine hood Stay away from the engine if you see or hear steam coming from it Turn off the engine and do not stand near the car until it cools down 80 Low Engine Coolant Level Warning Lamp With the key in steering lock position 2 the warning lamp comes on and goes out
114. t you break in new tires for approx 60 miles 100 km at moderate speed It is imperative that the wheel mounting bolts be retightened after approx 60 300 miles 100 500 km 98 On new vehicles retightening is carried out during the 1st inspection Retightening is also necessary whenever wheels are fitted e g when the spare wheel is used for the first time or when a set of wheels with M S tires is installed Tightening torque 110 ft Ib 150 Nm For rim and tire specifications refer to Technical Data Warning Worn old tires can cause accidents If the tire tread is badly worn or if the tires have sustained damage replace them When replacing rims use only genuine Mercedes Benz wheel bolts identified by Mercedes star specified for the particular rim type Failure to do so can result in the bolts loosening and possibly an accident Rotating Wheels Tire rotation is permissible only if all four wheel rims are of the same size The wheels can be rotated according to the degree of tire wear while retaining the same direction of travel Rotating however should be carried out at the scheduled maintenance intervals before the characteristic tire wear pattern shoulder wear on front wheels and tread center wear on rear wheels becomes visible as otherwise the driving properties deteriorate Important Unidirectional snow tires must always be mounted with arrow on tire sidewall pointing in di
115. te S and water for temperatures above freezing or MB Windshield Washer Concentrate S and commercially available premixed windshield washer solvent antifreeze for temperatures below freezing Follow suggested mixing ratios see Windshield Headlamp Washer System in Index 131 Engine Oils Engine oils are specifically tested for their suitability in our engines Therefore use only engine oils recommended by Mercedes Benz Information on recommended brands is available at your authorized Mercedes Benz dealer Please follow maintenance booklet recommendations for scheduled oil changes Failure to do so could result in engine damage not covered by the Mercedes Benz Limited Warranty Engine Oil Additives Do not blend oil additives with engine oil They may be harmful to the engine operation Damage or malfunctions resulting from blending oil additives are not covered by the Mercedes Benz Limited Warranty Air Conditioner Refrigerant Ozone friendly HFC 134a refrigerant and special lubricating oil is used in the air conditioner system Never use R 12 CFC or mineral based lubricating oil otherwise damage to the system will occur Brake Fluid During vehicle operation the boiling point of the brake fluid is continuously reduced through the absorption of moisture from the atmosphere Under extremely hard operating conditions this moisture content can lead to the formation of bubbles in the system thus red
116. th engine running Otherwise deadly carbon monoxide CO gases may enter vehicle interior resulting in unconsciousness and death To assure sufficient fresh air ventilation open a window slightly on the side of the car that is out of the wind Passenger Compartment Warning Always fasten items being carried as securely as possible In an accident during hard braking or sudden maneuvers loose items will be thrown around inside the vehicle and cause injury to vehicle occupants unless the items are securely fastened in the vehicle 19 20 Operation 21 Air Outlets 1 2 Air volume control for left air outlet turn left open Air volume control for left center air outlet turn left open Air volume control for right center outlet turn left open Air volume control for right air outlet turn left to open o0 Left center air outlet adjustable Right center air outlet adjustable Side air outlet left and right adjustable Push button for center air outlets Heated air supply red indicator Non heated cooled air supply blue indicator Basic mode None of the push buttons 8 or 9 is pressed Dust Filter Dust particles down to a Certain and pollen are filtered Out before outside air enters the passenger compartment through the air distribution system 22 Automatic Climate Control Left side passenger compartment hwWON eS Temperature selector Temperature display Automatic mode
117. the system see Remote Control Infrared in Index 30 Closing Windows and Sliding Pop Up Roof from Outside Continue to press transmit button 1 after locking car Distance to receiver max 10 ft 3 m The windows and sliding pop up roof begin to close after approx 1 second Warning Never close the windows or sliding pop up roof if there is the possibility of anyone being harmed by the closing procedure In case the closing procedure causes potential danger the closing procedure can be immediately reversed by releasing and pressing the remote control button again until the green indicator lamp at the receiver blinks The sliding pop up roof and windows will open again The sliding pop up roof will only open if it was not fully closed Note If the side windows and sliding pop up roof cannot be closed automatically by using the key or by pressing the transmit button of the infrared remote control e g after a battery change press side of power window switch in center console until the window is completely closed and hold for additional 2 seconds Repeat procedure for each window The automatic closing procedure of the windows and sliding pop up roof should now be restored 31 TS pregare Central Locking System The entire vehicle may be locked or unlocked by either using the master key in the door or trunk locks or central locking switch located in driver s door The central locking syste
118. the system including incorrect installation and removal can lead to possible injury through an uncontrolled activation of the SRS In addition through improper work there is the risk of rendering the SRS inoperative Work on the SRS must therefore only be performed by an authorized Mercedes Benz dealer When scrapping the airbag unit or emergency tensioning retractor it is mandatory to follow our safety instructions These instructions are available at your authorized Mercedes Benz dealer When you sell the vehicle we strongly urge you to give notice to the subsequent owner that it is equipped with an SRS by alerting him to the applicable section in the Owner s Manual 53 Infant and Child Restraint Systems We recommend that all infants and children be restrained at all times while the vehicle is in motion Important The use of infant or child restraints is required by law in all 50 states and all Canadian provinces Infants and small children should be seated in an infant or child restraint system which is properly secured by a lap belt or lap belt portion of a lap shoulder belt and that complies with U S Federal Motor Vehicle Safety Standard 213 and Canadian Motor Vehicle Safety Standard 213 1 A state ment by the child restraint manufacturer of compliance with this standard can be found on the instruction label on the restraint and in the instruction manual provided with the restraint Whe
119. ting with the last connection made first When removing each clamp make sure that it does not touch any other metal while the other end is still attached Warning Never lean over batteries while connecting or jump starting you might get injured Battery fluid contains sulfuric acid Do not allow this fluid to come in contact with eyes skin or clothing In case it does immediately flush affected area with water and seek medical help A battery will also produce hydrogen gas which is flammable and very explosive Keep flames or sparks away from battery avoid improper connection of jumper cables smoking etc Important A discharged battery can freeze at approx 14 F 10 C In that case it must be thawed out before jumper cables are used A frozen battery can explodes and cause personal injury Jumper cable specifications Minimum cable cross section of 25 mm or approx 2 AWG Maximum length of 11 5 ft 3 5 m 111 Towing the Vehicle The rear towing eye is located at the right below the bumper The front towing eye is located on the passenger side behind a flap in the bumper panel Flap removal Insert finger in recess of flap and pull flap out Flap installation Engage flap at bottom and press in top securely We recommend that the vehicle be transported using flat bed equipment This method is preferable to other types of towing The vehicle may be towed with all wheels on the gr
120. ttent wiping Il Normal wiper speed Ill Fast wiper speed When coming to a stop or driving slower than approx 16 mph 25 km h the wiper speed automatically switches to the next lower setting In setting I the interval between wipes is lengthened Upon accelerating again the wiper speed returns to the previous setting Note The windshield washer reservoir hoses and nozzles are automatically heated 56 Windshield Washer Fluid Mixing Ratio For temperatures above freezing MB Windshield Washer Concentrate S and water 1 part S to 100 parts water 40 ml S to 1 gallon water For temperature below freezing MB Windshield Washer Concentrate S and commercially available premixed windshield washer solvent antifreeze 1 part S to 100 parts solvent 40 ml S to 1 gallon solvent Windshield Wiper Smears If the windshield wiper smears the windshield even during rain activate the washer system as often as necessary The fluid in the washer reservoir should be mixed in the correct ratio Blocked Windshield Wiper If the windshield wiper becomes blocked for example due to snow switch off the wiper motor For safety reasons before removing ice or snow remove key from steering lock Remove blockage Activate combination switch again key in steering lock position 1 Emergency Operation of Windshield Wiper In case of windshield wiper malfunction in switch positions I or III turn co
121. ucing the system s efficiency The brake fluid must therefore be replaced every two years preferably in the spring It is recommended to use only brake fluid approved by Mercedes Benz Your authorized Mercedes Benz dealer will provide you with additional information Premium Unleaded Gasoline Caution To maintain the engine s durability and performance premium unleaded gasoline must be used If premium unleaded is not available and low octane fuel is used follow these precautions have the fuel tank filled only partially with unleaded regular and fill up with premium un leaded as soon as possible avoid full throttle driving and abrupt acceleration do not exceed an engine speed of 3000 rpm if the vehicle is loaded with a light load such as two persons and no luggage do not exceed 7 3 of maximum accelerator pedal position if the vehicle is fully loaded or operating in mountainous terrain 132 Fuel Requirements Use only Premium unleaded meeting ASTM standard D 439 The octane number posted at the pump must be 91 min It is an average of both the Research R octane number and the Motor M octane number R M 2 This is also known as ANTI KNOCK INDEX Unleaded gasoline containing oxygenates such as Ethanol IPA IBA and TBA can be used provided the ratio of any one of these oxygenates to gasoline does not exceed 10 MTBE not to exceed 15 The ratio of Methanol to gasoline must not exceed 3 p
122. ume If the lever is briefly pushed to position 4 when driving at a speed exceeding approx 25 mph 40 km h the vehicle resumes the speed which was set prior to the cancellation of the cruise control The last memorized speed is canceled when the key in the steering lock s turned to position 1 or 0 Note If the engine does not brake the vehicle sufficiently while driving on a downgrade the speed you set on the cruise control may be exceeded and you may have to step on the brake pedal to slow down As soon as the grade eases the cruise controlled speed will again be maintained as long as the brakes were not previously applied or the lever may be used to resume the previously set speed if the brakes were applied Caution When driving with the cruise control the transmission selector lever must not be shifted to position N as otherwise the engine will overrev Warning Only use the cruise control if the traffic and weather conditions make it advisable to travel at a steady speed The use of cruise control can be dangerous on winding roads or in heavy traffic because conditions do not allow safe driving at a steady speed The use of cruise control can be dangerous on slippery roads Rapid changes in tire adhesion can result in wheel spin and loss of control The Resume function should only be operated if the driver is fully aware of the previously set speed and wishes to resume this particular preset s
123. ure by changing the pressure regulator 1 setting Multicontour Backrest Bottom Center Top Pressure regulator Side bolster adjustment nah WN Some models may be equipped with orthopedic seats These seats have inflatable air cushions built into the backrest to provide additional lumbar and side support The amount of cushion height and curvature may be adjusted after turning the key in steering lock to position 2 The center section 2 can be selected together with bottom section 1 or top section 3 The inflation pressure of the air cushion can be continuously varied between position 0 without pressure and position 5 maximum pressure by changing the pressure regulator 4 setting The side bolsters of the backrest can be adjusted with push button 5 e pushing forward increase side support e pushing backward decrease side support If the engine is turned off the last cushion setting is retained in memory and automatically adjusts the cushion to this setting when the engine is restarted 40 P97 0073 Bt3 Heated Seats The front seat heater switches are located to the left and right side of the center console ashtray The front seat heaters can be switched on with the key in steering lock positions 1 or 2 the rear seat heaters only in steering lock position 2 Press switch to turn on heater 1 Normal heating mode One indicator lamp in the switch lights up 2
124. ve the Service Booklet with you when you take the vehicle to your authorized Mercedes Benz Center for service The service advisor will record each service in the booklet for you Roadside assistance The Mercedes Benz Roadside Assistance Program provides factory trained technical help in the event of a breakdown Calls to the toll free Roadside Assistance number 1 800 222 0100 in the USA only will be answered by Mercedes Benz Client Assistance Representatives 24 hours a day 365 days a year For additional information refer to the Mercedes Benz Roadside Assistance Program brochure in your glove box Change of address or ownership If you change your address be sure to send in the Change of Address Notice found in the Owner s Service and Warranty Policy Booklet It is in your own interest that we can contact you should the need arise If you sell your Mercedes please leave all owner s literature with the vehicle to make it available to the next owner If you bought this vehicle used be sure to send in the Notice of Purchase of Used Car found in the Owner s Service and Warranty Policy Booklet Operating your vehicle outside the USA or Canada If you plan to operate your vehicle in foreign countries please be aware that service facilities or replacement parts may not be readily available Certain Mercedes Benz models are available for delivery in Europe under our European Delivery Program For details consult your authorized Merce
125. w 2 in either F or C 3 14 Automatic Mode This is the normal setting Air volume and distribution are controlled automatically To select Press button indicator lamp lights up To change selection E Aaa button indicator lamp of selected button lights up The indicator lamp for button goes out Note If the Automatic Climate Control is in the Diagnosis Mode turn key in steering lock to position 0 to return it to its normal operation 5 Defrost Maximum heated and automatically controlled amount of air is directed to the windshield and side windows As the engine coolant temperature increases the air volume is auto matically increased thereby defrosting as quickly as possible Open and direct air outlets 7 towards the side windows Note Press KM once again to return to previous setting Defogging Windows Switch off or switch on left and right side or switch on Note To quickly defog the inside of the windshield select the largest air volume and air distribution button 24 6 Residual Engine Heat Utilization Fix With the engine switched off it is possible to continue heating the interior for a short while The rear passenger compartment air outlet must be closed Air volume and distribution are controlled automatically To select Turn key in steering lock to position 1 or 0 or remove key Press button indicator lamp lights up This function selection wil
126. when the engine is running If the warning lamp does not go out after starting the engine or if it comes on while driving then the coolant level has dropped below the required level If no leaks are noticeable and the engine temperature does not increase continue to drive to the nearest service station and have coolant added to the coolant system See Index The low engine coolant level warning light should not be ignored Extended driving with the light illuminated may cause serious engine damage not covered by the Mercedes Benz Limited Warranty In cases of major or frequent minor coolant loss have the cooling system checked at your authorized Mercedes Benz dealer as soon as possible Note Do not drive without coolant in the cooling system The engine will overheat causing major engine damage Monitor the coolant temperature gauge while driving Warning Do not spill antifreeze on hot engine parts Antifreeze contains ethylene glycol which may burn if it comes into contact with hot engine parts You can be seriously burned Low Windshield and Headlamp Washer System Fluid Level Warning Lamp With the key in steering lock position 2 the warning lamp comes on and goes out when the engine is running If the warning lamp comes on with the engine running the level of the reservoir has dropped to approx of the total volume The reservoir should be refilled with MB Windshield Washer Concentrate S and w

Mercedes-Benz S 500 Automobile User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents