Home

Mercedes-Benz 2011 E350 Sedan Automobile User Manual

1. To release the parking brake f l e While pressing the release button pull the handle upward ha to release the brake e Push handle downward to the off position le 95 Driving TRANSAXLES Automatic The normal driving position for the automatic transaxle is the position To move the automatic transaxle gearshift P Park R Reverse N Neutral Overdrive the normal driving position for best fuel economy D Drive more engine braking than L Low more engine braking than D at speeds up to 60 km h 38 mph 96 Driving AN Hold the brake the pedal down while you move the gearshift lever from position to position If you do not hold the brake pedal down your vehicle may move unexpectedly and cause injury Moving a locked gearshift Automatic transaxle vehicles are equipped with a shift lock safety feature that prevents the gearshift from being moved out of P without the brake pedal depressed If you cannot move the gearshift out of P with the brake pedal depressed 1 Continue depressing the brake pedal and remove the shift lock override cap with a 2 5 cm 1 inch or longer screwdriver 2 Insert the screwdriver into the shift lock override opening and push down 97 Driving 3 Push and hold the thumb button 4 Move the gearshift If it is necessary to use the above procedure to move the gearshift it is possible that a fus
2. e the vehicle is raised for service e the sound of the exhaust system changes e the vehicle has been damaged in a collision Improve vehicle ventilation by keeping all air inlet vents clear of snow leaves and other debris 91 Starting If the engine is idling while the vehicle is stopped in an open area for long periods of time open the windows at least 2 5 cm 1 in Adjust the heating or air conditioning if equipped to bring in fresh air If equipped with air conditioning 92 Driving BRAKES Power assisted brakes Apply the brake pedal gradually to avoid locking up the wheels The brakes will adjust automatically as the brake pads or linings wear down Utilize these strategies for maximum braking performance e f driving down a long or steep hill shift to a lower gear and do not apply the brakes continuously Continuously applying the brakes on a hill could overheat them and make them less effective Occasional brake squeal during light to moderate stops is normal Significantly increased squeal is an indicator that brake service is needed Apply the brakes gently several times after driving through standing water or washing your vehicle to dry them Anti lock brake system ABS Apply ABS brakes steadily Do not pump the brakes in a panic stop The brake system will prevent wheel lockup by automatically releasing and reapplying the brakes Even with ABS
3. 110 kPa 16 psi Engine coolant e automatic transaxle 6 0 L 6 3 qt e manual transaxle 5 0 L 5 3 qt LUBRICANT SPECIFICATIONS Item Ford part Ford part Ford name number specification Brake master Ford High C6AZ 19542 AB ESA M6C25 A cylinder Performance DOT 3 DOT 3 Motor Vehicle Brake Fluid Constant CV Joint E43Z 19590 A ESP MIC207 A velocity joints Grease High Temperature Door Silicone weatherstrips Lubricant tube COAZ 19553 AA ESR M13P4 A aerosol D7AZ 19553 AA ESR M13P4 A Engine coolant Ford Premium E2FZ 19549 AA ESE M97B44 A Cooling System B Fluid 180 Capacities and specifications Item Ford part Ford part Ford name number specification Engine oil Motorcraft X0 5W 30 WSS M2C153 F 5W 30 Super Premium Motor Oil Hinges and Ford F5AZ 19G209 AA ESR M1C159 A latches Multi Purpose and Grease Spray ESB M1C93A Aerosol Lock cylinders Penetrating E8AZ 19A501 B N A Lubricant Power steering Premium E6AZ 19582 AA ESW M2C33 F pump Power Steering Fluid Automatic and Motorcraft XT 2 BDX MERCON manual MERCON QDX transaxle Multi Purpose ATF Transmission Fluid Wheel bearings Motorcraft XG 1 C K ESA M1C75 B rear Premium Long Life Grease Windshield Ultra Clear C9AZ 19550 AC ESR M17P5 A washer fluid Windshield or reservoir Washer C9AZ 19550 BC Concentrate 181 Capacities and specifications ENGINE DAT
4. The vehicle identification number VIN is attached to a metal tag and is located in the following areas of your vehicle for maximum theft protection e left and right front fenders e hood e left and right front doors e front and rear bumper e left and right rear quarter panels e decklid e liftgate e engine compartment e transaxle Engine number The engine number is stamped on the engine block 185 Reporting safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying Ford Motor Company If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect existing in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Ford Motor Company To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 202 366 0123 in the Washington D C area or write to NHTSA U S Department of Transportation 400 Seventh Street Washington D C 20590 You can also obtain other information motor vehicle safety from the hotline 186 Aiming headlamps secc 173 Air bag supplemental restraint SYSTEM ea dssvedsavcses cee e a a a 62 description eee 62 63 disposal oo 63
5. To avoid damage or injury follow these directions in the order they are given If in doubt call for road service Before jump starting a vehicle e make sure the booster battery vehicle has a 12 volt starting 120 Roadside emergencies system a 24 volt power supply will cause vehicle damage e park the vehicles close to each other but do not allow the two vehicles to touch e check to make sure neither battery is disconnected e remove any excessive corrosion from the battery terminals e turn on the heater fan in each vehicle to prevent damage from voltage surges To jump start the vehicle 1 Connect the jumper cables in numerical order Disabled battery positive terminal 2 Booster battery positive terminal G Booster battery negative terminal Disabled vehicle engine Do not connect the end of the second cable to the negative terminal of the battery to be jumped A spark may cause an explosion of the gases that surround the battery 2 Start the engine in the vehicle with the booster battery 3 Wait a few minutes and start the engine in the vehicle with the disabled battery 121 Roadside emergencies 4 Disconnect the jumper cables in numerical order Engine 2 Booster battery negative terminal G Booster battery positive terminal Previously disabled battery positive terminal Let the vehicle idle for a few minutes to allow the engine to relea
6. driver air bag weet 64 indicator light wc 7 64 OperatiON sasra aidean asa 63 tone generator cece 64 wearing safety belts 64 Air cleaner filter oo 145 replacing nerisersaaniniiueiia 146 Air conditioning manual heating and air conditioning System seess 19 Anti lock brake system ABS 93 NOISE era 93 see also Brake cece 93 Warning ight eneas 94 Anti theft system ou cece 45 arming the system sesccecssn 50 dESCrIpTON sciidtiidesenanacrais 50 disarming a triggered system 52 disarming an untriggered SV SEO E 51 Warning light assesseer 9 Automatic transaxle esses 96 driving WIth oo eeeeeseeseeseeesseeeees 96 fluid adding ecserin 141 fluid checking esscscrere 140 Batey earann aa 142 Servicing hesiari naani 143 Brakes s sasciraisayiyeli cite tan avin 93 ANUI lOCK evieeunvinedornniedees 93 anti lock brake system ABS warning LIGNt cccceeseeteereeeees 9 fluid checking and adding 133 power braking sacscisiiiiiivii 93 Break in period cccceseeeeees 2 Bulbs replacing escccccceres 160 halogen ou sessecsesesssseeesessesesereees 161 headlamps roris 162 high mount brakelamp 164 rear lamps n e 164 165 167 168 SPECIFICATIONS isinsi 172 Cargo area shade scce 41 Changing a tire wcrc 114 Charging system warning light 9 Child safety seats ANd air bags occ 185 Childproof lOCKS wo eee 33 Cleaning your vehicle ne 175 built in child seat wo 178 engine compart
7. normal range add engine oil by removing the i oil filler cap and pouring in oil 3 Confirm that the oil level is full but be careful not to overfill the engine CG ef AM NO eS ev DVN N Iz Sma See DAA uy Continuous contact with USED motor oil has caused cancer in laboratory rats 132 CHECKING AND ADDING BRAKE FLUID Brake fluid should be checked and refilled as needed at least once a year e Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir Visually inspect the fluid level If necessary add brake fluid until the level reaches MAX e Use only a DOT 3 brake fluid certified to meet Ford specifications Refer to Lubricant specifications in the Capacities and specifications chapter A Brake fluid is toxic AN If you use brake fluid that is not DOT 3 you will cause permanent damage AN Do not let the reservoir in the master cylinder run dry This may cause the brakes to fail Maintenance and care 133 Maintenance and care CHECKING AND ADDING MANUAL TRANSAXLE CLUTCH FLUID The brake fluid reservoir and clutch master cylinder are part of the same unit both are refillable through the brake fluid reservoir with brake fluid During normal operation the fluid level in the brake fluid reservoir will rise slowly For more information on brake fluid maintenance refer to Checking and adding brake fluid in this chapter CHECKING AND
8. 2 With the vehicle running and the brake pedal depressed move the gearshift through each of the gear ranges allowing each gear to engage 3 Move the gearshift to P 140 4 Set the parking brake 5 Remove the dipstick and wipe it with a clean dry rag 6 Install the dipstick 7 Remove the dipstick and inspect the fluid level Your vehicle should not be driven if the fluid level is below the bottom hole in the dipstick and outside temperatures are above 10 C GORE When adding automatic transaxle fluid e Ensure that the correct type is added For automatic transaxle fluid specifications refer to Capacities and specifications in this chapter Maintenance and care Tl 65 C 149 F 20 C 68 F FAOZ 141 Maintenance and care Add the fluid in 250 ml pint increments through the filler tube Do not overfill the automatic transaxle fluid reservoir If this occurs the excess fluid should be removed by a qualified technician Always dispose of used automotive fluids in a responsible manner Follow your community s standards for disposing of these types of fluids Call your local recycling center to find out more about recycling automotive fluids Checking and adding manual transaxle fluid For information on checking and adding manual transaxle fluid refer to Checking and adding clutch fluid in this section WHAT YOU SHOULD KNOW ABOUT YOUR BATTERY
9. High beams IIluminates when the headlamp high beams are on Anti theft if equipped IIluminates when the anti theft system is arming and flashes when the anti theft system is armed Charging IIluminates when there is a problem with the alternator or charging system and the electrical system requires service The light will also briefly illuminate when the ignition key is turned to ON and the engine is off Oil pressure IIluminates when the oil pressure is low not the low oil level However if your engine s oil level is low it could affect the oil pressure Stop the vehicle and check the oil level as soon as possible Do not drive the vehicle if the light remains on The light will also briefly illuminate when the ignition key is turned to ON and the engine is off Instrumentation 485 ac D THEFT Instrumentation Engine coolant IIluminates when there is low coolant level or a problem with the CHECK engine coolant system Stop the COOLANT vehicle and check the engine coolant level as soon as possible The light will also briefly illuminate when the ignition key is turned to ON and the engine is off For more information on engine coolant refer to Checking and adding engine coolant in the Maintenance and care chapter Liftgate ajar if equipped IIluminates when the ignition is in the ON position and the liftgate is aa open Many of the lights illuminate briefly when you start the veh
10. If the original equipment maintenance free battery needs replacing it may be replaced with a low maintenance battery F or information on appropriate replacement batteries refer to Motorcraft part numbers in the Capacities and specifications chapter 142 Maintenance and care AN Batteries normally produce explosive gases that can cause personal injury Do not allow flames sparks or lit smoking materials to come near the battery When charging or working near a battery always cover your face protect your eyes and provide ventilation Batteries contain sulfuric acid that can burn skin eyes and clothing A Applying too much pressure on the ends when lifting a battery could cause acid to spill Lift the battery with a carrier or with your hands on opposite corners Servicing your battery The low maintenance battery has removable vent caps for checking the electrolyte level and adding water Check the electrolyte level every 24 months or 40 000 km 24 000 miles in average temperatures below 32 C 90 F Keep the electrolyte level in each cell up to the level indicator Do not overfill 143 Maintenance and care If the electrolyte level becomes low refill the battery with distilled water If necessary distilled water may be substituted with tap water that is not hard and does not have a high mineral or alkali content If the battery needs water quite often have the charging system checked for
11. Motor Vehicle Safety Standard No 109 Grades A and B represent higher levels of performance on the laboratory test wheel than the minimum required by law 149 Maintenance and care The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat build up and possible tire failure SERVICING YOUR TIRES Checking the tire pressure Check the tire pressure periodically and inflate tires as necessary To check the tire pressure insert the tire pressure gauge into the valve stem The cold pressure amount is listed on the Safety Compliance Certification Label located on the passenger s door inside latch pillar AN Improperly inflated tires can affect vehicle handling and can fail suddenly possibly resulting in loss of vehicle control 150 Rotating your tires Rotate your tires at regular intervals to ensure even wear These intervals are listed in the Service Guide e Four tire rotation e Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads AN When replacing full size tires never mix radial bias belted or bias type tires Use only the tire sizes that are listed on the tire pressure decal Maintenance and care b 151 M
12. OWS cicdveevess dnetardi siden 34 Power steering fluid checking and adding 139 Rear window deoe cenana 24 WaSNE dessini 30 WID Cle ea e Carta astest 30 Refill capacities for fluids 179 Relays tient area r 109 Remote control ssssccccccss 45 Remote entry System oo eee 45 illuminated entry occ 49 locking unlocking doors 46 47 Opening the trunk sssseseres 47 PANIC AAPM v ceessecssessseeesseeeeeens 49 Repairing paint chips seese 176 Reporting safety defects 186 Restraints safety see Safety restraints tansicdncidiainaine 55 ner EEE T cer rtrerrec rere 54 TINFANE siise adinaren ienien 67 Roadside emergencies s 107 Safety chains when towing a trailer sorcerien 104 Safety defects reporting 186 Safety restraints ce 55 adjusting the safety belts 59 automatic locking mode retractor smississaknininsiaa 57 for CHIIDrEN occ 65 lap and shoulder belts 56 59 MAINTENANCE oe ects eteteteeeee 60 proper USE ceeeeeeeseeeeeees 55 56 vehicle sensitive locking MOG iren enn warning light and chime 8 10 8 Safety seats for children 67 automatic locking mode retractor x s cseieecvdenuavs 81 built in Child Seat occ 74 IN Front S at sacininirispnrs 68 IN rear seat ve eeeceessesteesseeeeeeens 70 tether anchorage hardware 71 SEATS piei T 53 adjusting the seat manual 53 child safety seats secc 67 folding rear seats oo 54 Index head
13. a possible malfunction Your vehicle is equipped with a battery saver control feature designed to prevent your battery from accidental wear down due to doors left ajar For information on the system and how it works see Interior overhead lamp in this chapter Because your vehicle s engine is electronically controlled some control conditions are maintained by power from the battery When the battery is disconnected or a new battery is installed the computer must relearn its idle conditions before your vehicle will drive properly To begin this process 1 Put the gearshift in P automatic transaxle or N manual transaxle 2 Turn off all accessories and start the vehicle 3 Let the engine idle for at least one minute 4 The relearning process will automatically complete as you drive the vehicle e If you do not allow the engine to relearn its idle the idle quality 144 of your vehicle may be adversely affected until the idle is eventually relearned If the battery has been disconnected or a new battery has been installed the clock and preset radio stations must be reset once the battery is reconnected Always dispose of used automotive batteries in a responsible manner Follow your community s standards for disposal Call your local recycling center to find out more about recycling automotive batteries CHECKING AND CHANGING YOUR AIR FILTER If the vehicle is operated in very dusty
14. adjusted before use e To shorten the belt 59 Seating and safety restraints Buckle the belt Pull the loose end of the belt until snug e To lengthen the belt Tip and pull the tongue The lap belt must fit snugly and as eae low as possible around the hips Do not wear the lap belt around your waist Safety belt maintenance Check the safety belt systems periodically for damage and to ensure that they work properly 60 Seating and safety restraints The short plastic boot on the front safety belt at the passenger inboard buckle location covers an energy absorbing sew pattern on the safety belt In the event of a collision the sew pattern may release and the orange portion of the warning label may become visible If this occurs the safety belt and buckle must be replaced Failure to follow these instructions will affect the performance of the safety belts and increase the risk of personal injury 61 Seating and safety restraints SAFETY BELT INDICATOR LIGHT AND WARNING CHIME A illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts Conditions of operation If Then The driver s safety belt is not buckled before the ignition key is turned to ON The safety belt indicator illuminates for one to two minutes and the warning chime sounds for 4 8 seconds The driver s side safety belt is buckled while the in
15. best airflow 23 Controls and features REAR WINDOW DEFROSTER IF EQUIPPED Press the defroster switch to clear the rear window of thin ice and fog The ignition must be in the ON position to operate the rear window defroster The defroster turns off automatically after fifteen minutes To manually turn off the defroster before fifteen minutes have passed push the switch again 24 Controls and features Ignition LOCK locks the steering wheel and allows the key to be removed from the ignition Push the key in while turning to LOCK on vehicles with manual transaxles LOCK also locks automatic transaxle gearshifts 25 Controls and features ACC allows operation of some accessories without starting the engine ON allows testing of the vehicle s warning lights START cranks the engine The key returns to the ON position after it is released For more information on the vehicle ignition and starting the vehicle refer to Preparing to start the vehicle in the Starting chapter Headlamp switch Rotate the headlamp switch to the desired position ZO Headlamps on O Parking lamps side marker lamps instrument panel lamps license lamps and tail lamps on OFF Lamps off Daytime running light DRL sysiem if equipped The DRL system turns on the high beam headlamps with a reduced light output when e the vehicle is running e the vehicle has a fully released par
16. child safety seats as specified by the manufacturer of your child safety seat should always wear safety belts Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child s face or neck the child should wear the lap and shoulder belt Moving the child closer to the center of the vehicle may help to provide a good shoulder belt fit To improve the fit of lap and shoulder belts on children who have outgrown child safety seats Ford recommends use of a belt positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards Belt positioning booster seats raise the child and provide a shorter firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child A 66 Seating and safety restraints belt positioning booster should be used if the shoulder belt rests in front of the child s face or neck or if the lap belt does not fit snugly on both thighs or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion You may wish to dicuss the specific needs of your child with your pediatrician CHILDREN AND INFANT OR CHILD SAFETY SEATS AN Carefully fol
17. engine block heater if equipped Engine block heaters are strongly recommended if you live in a region where temperatures consistently reach 29 C 20 F or below during the winter months An engine block heater warms the engine coolant which improves starting warms up the engine faster and allows the heater defrost system to respond quickly If your vehicle is equipped with an engine block heater use it whenever the temperature is 23 C 10 F or below To turn the heater on plug it into a grounded 110 volt outlet It is recommended that you use a 110 volt circuit that is protected by a Ground Fault Circuit Interrupter For best results plug the heater in at least three hours before you start your vehicle Using the heater for longer than three hours will not damage the engine so you can 90 Starting plug it in at night to start the vehicle the next morning AN Do not use your heater with ungrounded electrical systems or two pronged cheater adapters You can be injured by an electrical shock if you use an ungrounded connection GUARDING AGAINST EXHAUST FUMES Carbon monoxide although colorless and odorless is present in exhaust fumes Take precautions to avoid its dangerous effects AN If you smell exhaust fumes inside your vehicle have your dealer inspect your vehicle immediately Do not drive if you smell exhaust fumes Have the exhaust and body ventilation systems checked whenever
18. increase the engine coolant concentration above 60 Leave a 50 50 mixture of engine coolant and water in your vehicle year round in non extreme climates 138 CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid at least twice a year by completing the following steps 1 Start the engine 2 When the engine coolant temperature gauge reaches the normal zone turn off the engine 3 Visually inspect the fluid level in the power steering reservoir 4 If necessary add power steering fluid until the fluid level reaches MAX Do not overfill the power steering reservoir e As a maintenance precaution visually inspect the lines and hoses of the power steering system for leaks and damage If new fluid is frequently required consult a qualified service technician CHECKING AND ADDING TRANSAXLE FLUID Checking and adding automatic transaxle fluid Check the automatic transaxle fluid according to the owner maintenance checks in the Service Guide Maintenance and care 139 Maintenance and care It is best to check the transaxle fluid level at the normal operating temperature after approximately 35 km 20 miles of driving If the transaxle fluid level must be checked under different circumstances make sure the outside temperature is above 10 C 50 F to obtain an accurate fluid level check Checking the automatic transaxle fluid 1 Park the vehicle on a level surface
19. is centered when viewed from directly above the bubble 4 Close the hood If the vehicle is on a downward or upward slope of not more than 1 2 the VHAD s bubble level can be used to correct for the effects of the surface slope provided that the slope is accurately known 174 Maintenance and care Each graduation of the bubble level represents 0 19 of downward or upward slope To correct for the effects of surface slope turn the vertical aim adjustment screw until the bubble is centered at a position corresponding to the slope of the surface CLEANING AND CARING FOR YOUR VEHICLE Contact your dealer for more information on recommended cleaners and their availability in your area Washing your vehicle Wash your vehicle regularly with cold or lukewarm water Never use strong detergents or soap If your vehicle is particularly dirty use a quality car shampoo Always use a clean sponge and plenty of water Ve for best results We recommend RRR that you have the underbody of your vehicle washed at the end of the winter to remove deposits left by snow salt and water Wax the body paintwork of your vehicle several times a year This will help to retain the glossy paintwork finish and water droplets will run off more easily A Remove any after dealer accessories such as antennae before entering a commercial car wash 175 Maintenance and care After washing your vehicle apply the brakes sev
20. not properly maintained the engine coolant temperature gauge will not read properly 13 Instrumentation Odometer The odometer gives a six digit reading of how many kilometers miles your vehicle has traveled 50 60 70 m 80 90 tee ae 40 160 Trip odometer The trip odometer gives a four digit reading of how many kilometers miles your vehicle has traveled in an individual trip Press the reset button to begin an individual trip odometer record Tachometer 14 Controls and features INSTRUMENT PANEL DIMMER SWITCH To adjust the instrument panel dimmer switch e Rotate the switch to the right to dim the instrument panel lighting e Rotate the switch to the left to brighten the instrument panel lighting 15 Controls and features POWER OUTSIDE MIRRORS IF EQUIPPED To adjust the outside mirrors 1 Select the mirror you want to adjust L Driver side mirror R Passenger side mirror 2 Move the mirror control in the desired direction 3 Lock the mirror by moving the switch to the center position 16 AUDIO SYSTEM For information on the audio system refer to the Audio Guide CLIMATE CONTROLS Your vehicle has one of the following climate control systems e Manual heating system e Manual heating and air conditioning system In some modes the two systems function similarly in modes where the systems do not function similarly the diffe
21. on Wait for them to reach a vertical position and turn the ignition to LOCK Do not move the wipers manually across the windshield this may cause damage to the wipers Inspect the wiper arm pivots on a regular basis to ensure that the wiper arms move freely Lubricate the pivot points as necessary Replacing wiper blades If the wiper blades do not work properly after cleaning replacement of the blade assembly or the blade element may be necessary There are three different lengths of wiper blades on your vehicle The driver side wiper blade is 51 cm 20 in long and the passenger side wiper blade is 44 5 cm 17 5 in long and the rear window wiper is 35 cm 13 75 in long Ensure that you install the correct length wiper blade in the correct location To replace the wiper blades Maintenance and care 147 Maintenance and care 1 Pull the wiper arm away from the windshield and lock into the service position 2 Turn the blade at an angle from the wiper arm Push the lock pin with a screwdriver to release the blade and pull the wiper blade down toward the windshield to remove it from the arm 3 Attach the new wiper to the wiper arm and press it into place until a click is heard WHAT YOU SHOULD KNOW ABOUT TIRE GRADES The U S Department of Transportation DOT requires Ford to give its customers the following tire information Treadwear The treadwear grade is a comparative rating based on t
22. or sandy areas replace the filter more often than the recommended intervals Do not drive without an air filter this could result in excessive engine wear Maintenance and care 145 Maintenance and care Changing your air filter 1 Unlock the clamp that holds the engine air cleaner assembly in place by releasing the clamp locking clip on the front portion of the assembly e The clamp will spring open and remain attached to the left side of the assembly 2 Swing the left side of the assembly open 3 Remove the air filter element from the open end of the engine air cleaner assembly and replace it with a new element e When replacing the element be sure to align the nubs on both the air cleaner element and the open end of the air cleaner assembly If these nubs are not aligned the new element will not fit properly within the assembly and the assembly may malfunction 4 Swing the left side of the assembly closed and secure the locking clamp CHECKING AND CHANGING YOUR WIPER BLADES Check the windshield wiper blades at least twice a year also check them whenever the wipers seem less effective than usual Substances such as tree sap and some hot wax treatments used by commercial car washes can reduce the effectiveness of wiper blades 146 KA ta jj NLA L h z lt S iN AT NST AA To make reaching the wiper blades easy simply turn the ignition to the ON position and turn the wipers
23. rear passenger side of your vehicle With the sedan model a label marks its location Press the button on the switch to reset the fuel pump e Sedan 43 Controls and features e Wagon 44 Controls and features REMOTE ENTRY AND ANTI THEFT SYSTEM e Sedan e Wagon Remote entry system if equipped The remote entry system is available as a driver door only or as an all door system The remote entry features only operate with the ignition in the OFF position When the ignition is in ON or ACC the system is disarmed If the vehicle is left running and locked the system will not allow reentry using the remote entry transmitter The operating range of the remote entry system may be affected by weather conditions such as very 45 Controls and features cold temperatures or structures around the vehicle buildings other vehicles radio and TV towers etc Typical operating range will allow you to be up to 10 meters 33 ft away from your vehicle Unlocking the doors and wagon liftgate Driver door only system e Press once to unlock the driver side door e Press again within five seconds to unlock the wagon liftgate if equipped e Sedan e Wagon All door system e Press once to unlock the driver side door 46 Controls and features e Press again within five seconds to unlock passenger doors and wagon liftgate if equipped Opening the trunk if equipped Press once
24. the trailer s safety chains to the vehicle To connect the chains cross the chains under the trailer tongue and attach to the vehicle frame or hook retainers not the bumper Make sure there is enough slack to allow the vehicle to turn corners Using trailer lamps See your local trailer dealer or rental agency for the proper instructions and equipment for hooking up trailer lamps Do not hook the trailer lights directly into the vehicle s lighting system wiring If the trailer lamps are not installed properly the warning lights in the instrument cluster may not work properly 104 Driving Driving while towing a trailer Do not drive faster than 88 km h 55 mph while towing a 454 kg 1000 Ib trailer Do not drive faster than 72 km h 45 mph with any weight trailer while towing in hilly country or on hot days Speed control if equipped may not work properly while towing on very long steep grades If driving with an automatic transaxle e use D or L rather than while towing up or down steep hills e anticipate stops and brake gradually If driving with a manual transaxle e select a gear that avoids jerking or excessive engine speed avoid driving excessively in first or second gear In first or second gear the trailer may be too big or too heavily loaded for the vehicle drivetrain shift to a lower gear while towing up or down steep hills anticipate stops and brake gradually Serv
25. warning light 64 Seating and safety restraints in the instrument cluster illuminates for approximately six seconds to indicate that the system is functional If you hear a group of five beeps or if the AF warning light does not illuminate stays lit or flashes the air bag system requires immediate service Have the vehicle serviced by your dealer CHILD RESTRAINT PRECAUTIONS You are required by law to use safety restraints for children in the United States and Canada If small children ride in your vehicle generally children who are four years of age or younger and who weigh 18 kg 40 Ib or less you must put them in safety seats made specially for children Check your local and state laws for specific requirements regarding the safety of your children AN Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision Always follow the instructions and warnings that come with any infant or child restraint you might use If possible place children in the rear seat of your vehicle Accident statistics suggest that children are safer when properly restrained in rear seating positions than when 65 Seating and safety restraints they are restrained in front seating positions A Rear facing infant seats should never be placed in the front seat CHILDREN AND SAFETY BELTS Children who are too large for
26. 3 instrument panel eces 111 FUSES gia 109 charts iraa 111 113 checking and replacing 109 Circuit breakers ssssssse 110 Gauges Electronic vo cece 12 Gauges Mechanical seee 12 engine coolant temperature Jage sisirin aienea ara ai 13 fuel gauge scsecccerrcine 13 odometer ssssssccsnerrcrrr 14 speedometer ssccccccrrrr 13 trip odometer crece 14 Gearshift ainiai 36 97 GVWR Gross Vehicle Weight RACING denisonii niii 101 dEfINIT ON oo ceeceessecsssstseeeeessnees 101 Hazard flashers esec 29 107 Head restraints oo 54 Headlamps daytime running lights 26 replacing DUIDS socs 162 turning on and Off ou 26 188 High beams indicator light voces 9 Operation sevieid cis dentdvanne 27 High mount brakelamp replacing the bulb ee 164 HOO misen n 128 prop rod hassei 128 release lever oo eee 128 working under the hood 124 Idle FEICAPNING isininioniiiiinianies 144 Ignition positions of the ignition 25 Inspection maintenance 1 M TOSCING A E E E 158 Instrument cluster 0 E eaa E 6 7 Standardi srir te Enei 6 Instrument panel cecceeeees 15 lighting up panel and interior 6 15 location of components 4 5 Interval WIperS nsessccccccess 30 J ump starting your vehicle 120 attaching cables nsec 121 disconnecting cables s 122 AMPS migrenin 160 bulb replacement specifications Chart 172 daytime running light system ce dome lAMPS occ 170 f
27. 51 km h 32 mph 4to5 66 km h 41 mph Upshift light if equipped The light in the instrument cluster illuminates to indicate when to shift for the best fuel economy The vehicle will not be harmed if the transaxle is not shifted when the light illuminates but the vehicle will use more fuel The light can be ignored when you are e downshifting e driving on steep hills e using the engine to brake the vehicle e seeking more power for a difficult acceleration To maximize gearshift performance 100 Driving Do not drive with your foot resting on the clutch pedal and do not use the clutch pedal to hold the vehicle at a standstill These actions will reduce clutch life Downshift on steep hills to reduce the vehicle s chances of stalling and to prevent unnecessary brake wear LOADING YOUR VEHICLE Before loading a vehicle familiarize yourself with these terms Base curb weight weight of the vehicle including any standard equipment fluids lubricants etc It does not include passengers or aftermarket equipment Payload combined maximum allowable weight of cargo passengers and optional equipment GVW Gross vehicle weight base curb weight plus the payload weight including passengers cargo and optional equipment Remember the GVW is not a limit or a specification GVWR Gross vehicle weight rating maximum total weight of the base vehicle passengers optiona
28. A Engine 2 0 liter 121 CID 4 cylinder in line compression ratio 9 2 1 single overhead cam split port induction SP1 Horsepower 110 at 5 000 rpm Torque 169 Nm 125 Ib ft at 3 750 rpm Required fuel grade 87 R M 2 Firing order 1 3 4 2 Injection timing Spark plug gap 1 3 to 1 4 mm 0 052 to 0 056 Ignition system DIS Valve clearances cold inlet exhaust 0 Maintenance free 0 Maintenance free VEHICLE DIMENSIONS Dimensions cm inches Sedan Wagon Overall length 443 25 cm 174 5 in 439 1 cm 172 9 in Overall width excluding exterior mirrors 168 00 cm 66 2 in 170 cm 67 in G Maximum height 135 00 cm 53 2 in 136 9 cm 53 9 in 4 Wheelbase 250 00 cm 98 4 in 250 cm 98 4 in G Track Front 143 5 cm 56 5 in 143 5 cm 56 5 in Rear 143 5 cm 56 5 in 143 5 cm 56 5 in 182 Capacities and specifications 183 Ze ities and specifications ZA om ls eek E Se gs eee Le L NA Z A_ E O 4 4 gt VARS ene Capacities and specifications IDENTIFYING YOUR VEHICLE Vehicle identification plate The vehicle identification plate is located on the front panel of the engine compartment This plate bears technical information on your vehicle and identifies various components Vehicle identification number
29. ADDING WASHER FLUID What you should know about washer fluid In freezing weather temperatures below 0 C 32 F washer fluid containing a small amount of antifreeze is used State or local regulations on volatile organic compounds may restrict the use of methanol a common type of antifreeze Use a non methanol antifreeze in freezing weather only if the fluid does not damage the paint finish wiper blades or washer system Washer fluid contains methanol and is poisonous Follow all instructions on the bottle of washer fluid 134 Maintenance and care Washer fluid for the windshield reservoir The vehicle s windshield washer fluid reservoir is located on the passenger side of the engine compartment If washer fluid needs to be added to the reservoir e Lift the windshield reservoir cover e Add enough washer fluid to fill the reservoir Washer fluid for the liftgate if equipped The wagon s rear reservoir is located on the passenger side of the storage compartment Remove the access cover to locate the washer reservoir cap The reservoir must be filled slowly to allow trapped air to escape 135 Maintenance and care ADDING ENGINE COOLANT Be careful not to add engine coolant to the windshield washer fluid reservoir If sprayed on the windshield engine coolant could make it difficult to see through the windshield When the engine is cool add a 50 50 mixture of engine coolant and wate
30. BEFORE DRIVING Introduction Instrumentation Controls and F eatures Seating and Safety restraints STARTING AND DRIVING Starting Driving Roadside Emergencies SERVICING Maintenance and Care Capacities and Specifications Reporting Safety Defects Index Contents 15 53 85 93 107 124 179 186 187 Introduction ICONS The following icons appear in this Owner Guide A A indicates a warning Read the following section on Warnings for a full explanation of warnings indicates that vehicle information related to recycling and other environmental concerns will follow Warnings Warnings remind you to be especially careful in those areas where carelessness can cause damage to your vehicle or personal injury to yourself your passengers or others Please read all warnings carefully Breaking in your vehicle Your new vehicle goes through an adjustment or breaking in period during the first 1 600 km 1 000 miles of driving During this period e change your vehicle s speed often as you drive Do not drive at one speed for a long time e use only the type of engine oil Ford recommends Do not use special break in oils e avoid sudden stops The break in period for brake linings lasts for 1 600 km 1 000 miles of highway driving or 160 km 100 miles of city driving Introduction Information about this guide This guide describes equipment and gives specifications for equip
31. Overhead lamp on Map lamps if equipped Press to turn the map lamps on and off DOOR MOUNTED CONTROLS Power door locks if equipped Push to lock or unlock the doors L All doors locked U All doors unlocked Controls and features 31 Controls and features e Driver side e Front passenger side 32 Childproof locks The rear doors can be set to prevent children from opening the doors from the inside To set the rear childproof locks The childproof lock must be set separately for each door Setting the lock on one door will not set the lock for both rear doors To return the rear doors to normal operation return the lever to the raised position Illuminated entry if equipped For more information on the illuminated entry system refer to Illuminated entry under Remote entry system in this chapter Controls and features 33 Controls and features Power windows if equipped Driver side controls Press the appropriate window switch to operate the power windows e Driver window e Front passenger window e Left rear passenger window 34 Controls and features e Right rear passenger window To prevent passengers from operating the power windows press the lock button Press again to unlock and allow the passengers to operate the power windows One touch down feature To open the driver side window completely press and release the lower portion of the driver sid
32. RAILER TOWING DRIVING IN SEVERE DUST POLICE TAXI OR DELIVERY Oil change intervals Refer to the Service Guide booklet for additional information Checking the engine oil Check the engine oil every time you fuel your vehicle 130 Maintenance and care To check the engine oil follow these steps 1 Once the engine is warm turn the engine off Make sure the vehicle is parked on level ground 2 Automatic transaxle e Engage the parking brake e Place the gearshift in P Manual transaxle e Engage the parking brake e Depress the clutch and place the gearshift in first gear 3 Open the hood If you need assistance refer to Opening the Hood in this chapter Protect yourself from engine heat 4 Remove the engine oil dipstick and wipe it clean Insert the dipstick fully then remove it again The oil level should be in the range shown on the dipstick 5 Carefully pull the dipstick out again If the oil level is below the ADD arrow add engine oil as necessary If the engine oil is beyond the FULL arrow engine damage or high oil consumption may occur and some oil must be removed from the engine 6 Put the dipstick back and ensure that it is properly seated 131 Maintenance and care Adding engine oil 1 Check the engine oil For instructions eo PSS refer to L Se Checking the A aS ENG AA engine oil in this chapter 2 If the fluid level is not within the
33. aintenance and care AN Make sure all replacement tires are of the same type load carrying capacity and tread design e g All Terrain as originally offered by Ford Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over IDENTIFYING TIRE TYPES Your vehicle requires the use of the following tire types wagon and sedan 18565R14 tires and T115 70D14 mini spare When purchasing replacemment tires for your vehicle consult your Ford or Lincoln Mercury dealer or qualified service technician to assure that correct tire types are used USING SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires currently on your vehicle The tires on your vehicle have all weather treads to provide traction in rain and snow However in some climates using snow tires and chains may be necessary Follow these guidelines when using snow tires and chains e Use only SAE Class S chains 152 Maintenance and care Install chains securely verifying that the chains do not touch any wiring brake lines or fuel lines Install tire chains on front tires only Drive cautiously If you hear the chains rub or bang against your vehicle stop and retighten the chains If this does not work remove the chains to prevent damage to your vehicle When possible avoid overloading your vehicle Remove the tire chains when the
34. and safety restraints 4 Insert the tongue into the proper buckle 5 Push down on the child safety seat while pulling on the loose part of the lap belt webbing to tighten the belt 6 Before placing the child in the child safety seat forcibly tilt the seat from side to side and forward and back to make sure the seat is securely held in place If the child seat moves excessively repeat steps five and six or properly install the child seat in a different seating position Using a tether strap Contact the manufacturer of your safety seat for information about ordering a tether strap if one is not provided with the seat The tether anchor hardware kit is part number 613D20 Your vehicle has tether anchor attachment locations on the rear package tray behind the back seat sedan or along the rear edge of the roof wagon Carefully follow ue instructions provided with the it 71 Seating and safety restraints Tether anchor hardware Canadian vehicles only All vehicles built for sale in Canada include a tether anchor hardware kit for use with Canadian child safety seats Attachment holes at each rear seating position have been provided in your vehicle to attach the anchor hardware if required Additional kits can be obtained at no charge from any Ford or Lincoln Mercury dealer Tether anchor hardware US vehicles only Vehicles built for sale in the US do not include a tether anchor hardware kit f
35. button to lower the head restraint To raise the head restraint pull without pushing the release button REAR SEATS Stow the built in child seat if equipped in order to fold the rear seatback down Refer to Built in child seat in this chapter for more information Push the seatback back to a raised position and latch for normal seating The full rear seat bench is shown The split folding rear seat if equipped operates in a similar manner Press to unlock the seatback 54 Seating and safety restraints SAFETY RESTRAINTS PRECAUTIONS The use of safety belts helps to restrain you and your passengers in case of a collision In most states and in Canada the law requires the use of safety belts To reduce the risk of serious injury in a collision always drive and ride with your seatback upright and the lap belt snug and low across the hips A Safety belts must be worn by all vehicle occupants to be properly restrained and help reduce the risk of injury in a collision AN To prevent the risk of injury make sure children sit where they can be properly restrained A It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed A Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts 55 Seating and safety restraints A Be
36. ch the socket from the housing and remove the bulb 4 Replace the bulb and ease the socket back into the housing 5 Replace the bulb assembly cover and secure the mounting screws License plate lamps To change the license plate lamp bulbs 1 Carefully remove screws and pull the license plate lamp assembly from the rear bumper 2 Carefully pull the lamp lens from the assembly 3 Remove the bulb to be replaced and install a new bulb 4 Replace the lamp lens the assembly and the screws 165 Maintenance and care e Sedan ac e Wagon 166 Tail lamps Backup lamps sedan The tail lamp assemblies and the backup bulb assemblies are located in the same portion of the vehicle rear one just below the other Follow the same steps to replace either bulb 1 Open the trunk lid to expose the tail lamp assembly Remove the two screws from the front of the lamp 2 The tail lamp has hidden fasteners which can be disengaged by hitting the lamp with your hand toward the side of the vehicle 3 Remove the socket that contains the burned out bulb by rotating it counterclockwise then pulling it out of the lamp assembly 4 Pull the burned out bulb from the socket and replace it with a new bulb Maintenance and care Q e 1 167 Maintenance and care 5 Push the socket into the lamp then secure it by rotating it clockwise 6 Position the tail lamp on the v
37. d for cleaning upholstery or carpets Do not bleach or dye the belts this may weaken the belt webbing Check the safety belt system periodically to ensure there are no nicks wear or cuts If the vehicle has been involved in an accident have all the safety belts and child seat anchoring brackets if equipped examined by a qualified technician 178 Capacities and specifications MOTORCRAFT PART NUMBERS Component Ford part number 2 0 liter SPI engine Air filter F7CX 9601 AA Battery BX 58C Fuel filter FG 862 Oil filter FL400 A PCV valve EV 229 Spark plug AGSF 34 E Refer to the Vehicle Emission Control Information VECI decal located on the underside of the hood for gap specifications REFILL CAPACITIES Your vehicle s fuel capacity The fuel capacity for your vehicle is 48 0 L 12 7 gallons e To avoid overspill from the filler neck stop fueling at the second automatic shut off e For more information on fueling your vehicle refer to Choosing the right fuel in the Maintenance and care chapter 179 Capacities and specifications Capacities liters quarts 2 0 liter SPI engine Engine Oil including filter excluding filter 3 8 L 4 0 qt 3 3L 3 5 qt Manual transaxle 3 35 L 3 55 qt Automatic transaxle full torque 3 9 L 4 1 gt 6 3L 6 7 qt converter empty torque converter Radiator filler cap
38. dicator light is illuminated and the warning chime is sounding The safety belt indicator light and the warning chime turn off The driver s safety belt is buckled before the ignition key is turned to ON The safety belt indicator light and warning chime remain off AIR BAG PRECAUTIONS Your vehicle is equipped with an air bag supplemental restraint system SRS designed to work with the safety belts to help protect you and your right front seat passenger in the event of a collision AN All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided 62 Seating and safety restraints A Do not place objects or mount equipment on or near the air bag cover on the steering wheel or in front seat areas that may come into contact with a deploying air bag Failure to follow this instruction may increase the risk of personal injury in the event of a collision Do not attempt to service repair or modify the air bag SRS or its fuses See your Ford or Lincoln Mercury dealer AIR BAG SYSTEM DESCRIPTION The air bags and their corresponding warning and information labels are found in the following locations The air bag system activates in collisions more severe than hitting a parked vehicle of similar size and weight head on at approximately 20 km h 13 mph This activation speed may vary if your vehicle is involved in a collis
39. e window switch To stop the window while it is in motion press the switch again Passenger controls Press the window switch to operate the power window at each door position 35 Controls and features e Front passenger side e Rear passengers CONSOLE CONTROLS Gearshift For information about the gearshift on vehicles with automatic or manual transaxles refer to the Transaxles section of the Driving chapter 36 e Automatic e Manual Controls and features 37 Controls and features Parking brake For information on the parking brake refer to Preparing to start the vehicle in the Driving chapter 38 Controls and features FLOOR CONTROLS Floor mat hook if equipped Fasten the floor mat to the floor to prevent the mat from shifting 39 Controls and features TRUNK LIFTGATE CONTROLS Compact disc changer if equipped For information on compact disc changer refer to the Audio Guide Wagon liftgate lamp Press the switch to turn the liftgate lamp on or off 40 Wagon sliding shade Pull the shade to cover the cargo area Hook the shade into the notches in the rear trim panels Rewinding the sliding shade If the shade is damaged or loses its spring tension from excessive use manual rewind of the shade may be necessary The following procedure is a two person operation Controls and features 41 Controls and fea
40. e has blown and the vehicle s brakelamps may not be operating properly F or more information on fuses and fuse replacement refer to Fuses and relays in the Roadside emergencies chapter A Do not drive your vehicle until you verify that the brakelamps are working If an automatic transaxle vehicle gets stuck in mud or snow it may be rocked out of the spot To rock the vehicle out shift between forward and reverse gears in a steady rhythm Press lightly on the accelerator in each gear Do not rock the vehicle for more than a few minutes this could damage the vehicle TIN Do not spin the wheels at over 55 km h 35 mph The tires may fail and injure a passenger or bystander 98 Manual To move the manual transaxle gearshift e Depress the brake pedal and then the clutch e Move the gearshift to the selected gear Always come to a complete stop before shifting into R Shift through the neutral position in the center before moving the gearshift into R If R is not engaged move the gearshift lever back to the neutral position release the clutch and try again Driving 99 Driving Upshifting For normal acceleration Upshift from At the following speed 1 to 2 22 km h 14 mph 2 to 3 40 km h 25 mph 3 to 4 58 km h 36 mph 4to5 72 km h 45 mph For cruising Upshift from At the following speed 1 to 2 18 km h 11 mph 2 to 3 35 km h 22 mph 3 to 4
41. e interior overhead lamp is located on the center of the ceiling of the vehicle To replace the bulbs 1 Remove the lamp lens by applying pressure to both tabs at the top of the lamp assembly and pulling the lens down and off 2 Pull the bulb to remove it and secure a new bulb 3 Replace the lamp lens by applying pressure to both sides of the lamp lens and popping the lens up and on to the lamp assembly I Goon L ly Oe AY 170 Maintenance and care The interior overhead lamp is equipped with a battery saver control system designed to prevent excessive wear on the battery When a door is not closed properly the battery saver control system timer is activated The timer will give you between eight and ten minutes to close the door before it automatically turns off the interior overhead lamp If the door is left open closed and then left open again the timer will automatically reset The battery saver control system is not activated when the headlamps are left on A warning chime will sound when the engine is turned off to draw your attention to headlamps left on Map lamp The map lamps are located in the rear portion of the interior overhead lamp assembly Replacement of the two bulbs requires removal of the bulb assembly cover and the use of several different tools See a qualified service technician or your dealer for replacement of the map lamp bulbs Hazard flasher For more informati
42. e is off Air bag readiness IIluminates when the air bag system requires servicing The light will also briefly illuminate when the ignition key is turned to ON Instrumentation LOW FUEL SERVICE ENGINE SOON As Instrumentation Safety belt The safety warning light chime is a reminder to fasten your safety belt One of the following will take place e If the lap shoulder belt is not buckled before the key is turned to the ON position the amp will illuminate for approximately one minute or until the safety belt is buckled If the lap shoulder belt is buckled while amp is illuminated and the chime is sounding both will turn off If the lap shoulder belt is buckled before the key is turned to the ON position neither light or chime will activate Upshift if equipped IIluminates when it is best to shift to the next highest manual transaxle gear for the maximum fuel economy Brake IIluminates when the parking brake is activated and the ignition is keyed to ON or the brake fluid level is low In addition with the parking brake off the light will illuminate when the engine is cranked t BRAKE OO Anti lock brake system ABS IIluminates when the ABS needs service The light will also briefly illuminate when the ignition key is turned to ON and the engine is off Turn signal IIluminates when the left hand or right hand turn signal or the hazard lamps are illuminated
43. ed by a qualified Dealer technician after any collision If the child seat was in use during a collision Ford recommends replacing it However if the collision was minor and a qualified technician finds that the child restraints do not show damage and continue to operate properly they do not need to be replaced Built in child seats not in use during a collision should also be inspected and replaced if either damage or improper operation is noted For information on cleaning your built in child seat refer to Cleaning the built in child seat in the Maintenance and care section 84 Starting A computer system controls the engine s idle revolutions per minute RPM When the engine starts the idle RPM runs higher than when the engine is warm If the engine idle speed does not slow down automatically have the vehicle checked Do not allow the vehicle to idle for more than ten minutes Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system creating the risk of fire or other damage A Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire A Do not start your vehicle in a closed garage or other enclosed area Never sit in a stopped vehicle for more than a short period of time with the engine running Exhaust fumes are toxic For more informat
44. ed trailer when figuring the total weight AN Towing trailers beyond the maximum recommended gross trailer weight exceeds the limits of the vehicle and could result in engine damage transaxle axle damage structural damage loss of control and personal injury Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle See your dealer or a reliable trailer dealer if you require assistance Auxiliary coolers are recommended for the power steering system and automatic transaxle system if equipped if you are planning on e traveling farther than 80 km 50 miles e towing in hilly terrain e towing frequently Using a hitch Do not use hitches that clamp onto the vehicle bumper Use a load carrying hitch Distribute the load so that only 10 to 15 of the total weight of the trailer is on the tongue Tie down the load so that it does not shift 103 Driving and change the weight on the hitch Using trailer brakes Use electric brakes or manual automatic or surge type hydraulic brakes that meet federal and local regulations Install and adjust the brakes according to the manufacturer s instructions AN Do not connect a trailer s hydraulic brake system directly to your vehicle s brake system Your vehicle may not have enough braking power and your chances of having a collision greatly increase Using safety chains Always connect
45. een involved in a collision or major jolt If the vehicle does not start it is possible that the fuel pump shut off switch needs to be reset AN If you see or smell fuel do not reset the switch or try to start your vehicle Have all passengers get out of the vehicle and call the local fire department or a towing service To reset the fuel pump press the button on the switch The switch is located immediately below the hole in the trunk side trim 107 Roadside emergencies xe oO N e e Wagon 108 Roadside emergencies FUSES AND RELAYS If electrical components in the vehicle are not working a fuse may have blown Blown fuses are identified by a broken wire Check the appropriate fuses before replacing any electrical components Use the fuse puller tool provided on the passenger compartment fuse panel cover to replace fuses AN Always replace a fuse with one that has the specified amperage rating Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire 109 Roadside emergencies Even after a fuse is replaced it will continue to blow if the cause of the overload is not identified and corrected If a fuse continues to blow have the vehicle s electrical system checked The POWER WIND 30A on the instrument panel fuse panel cover represents a circuit breaker that contols the vehicle s power windows The circuit breaker is located just ab
46. ehicle and gently hit the lens to engage the clips Replace the screws Tail lamps Backup lamps wagon To replace the tail lamp bulbs 1 Open the liftgate to expose the tail lamp assembly Remove the lens screws and pull the lens aside 2 Remove the socket that contains the burned out bulb by rotating it counterclockwise then pulling it out of the lamp assembly 3 Pull the burned out bulb from the socket and secure a new bulb 4 Push the socket into the lamp then secure it by rotating clockwise 5 Position the lamp on the vehicle and replace the screws 168 The side marker lamp assemblies are accessible through the interior of the vehicle The right assembly when facing the front of the vehicle is behind the same interior panel as the liftgate washer fluid the left assembly is located behind a similar looking interior panel directly opposite the right panel Both access panels are directly below the rear side windows To replace the backup lamp bulbs 1 Open the liftgate and lean inside the vehicle Access the backup bulb assemblies by carefully pulling open the interior panel Maintenance and care ia 169 Maintenance and care 2 Remove the bulb assembly form the interior recess 3 Twist the bulb counterclockwise to remove it and secure a new bulb 4 Replace the bulb assembly in the interior recess and replace the access panel Interior overhead lamp Th
47. emote entry transmitter if equipped The illuminated entry function illuminates the interior overhead lamp for approximately 20 seconds until the key is inserted into the ignition and turned to ON or until the LOCK button is pressed on the remote entry transmitter The interior overhead lamp must be set to the DOOR position in order for the 49 Controls and features illuminated entry system to activate Anti theft system if equipped The anti theft system protects against unauthorized entry into an armed and locked vehicle When an unauthorized entry occurs the system activates and e flashes the parking lamps and anti theft indicator light e sounds the horn The horn and parking lamps shut off after approximately three minutes The lights and horn will remain off unless another unauthorized entry is attempted Arming the system The anti theft system can be armed when e the ignition is in the LOCK position and the key is removed e the panic alarm is off e all doors are closed 50 Controls and features Press once to arm the anti theft system The THEFT light in the instrument cluster illuminates until the arming procedure is complete After the arming procedure is complete the THEFT light flashes Disarming an untriggered system Press once to disarm the untriggered anti theft system If the driver armed the system but did not exit the vehicle the system can also be disarmed by insertin
48. eral times to dry them Repairing paint chips Minor scratches or paint damage from road chippings may be camouflaged with Ford exterior lacquer touch up paint AL81 XXXX B or ALBZ 19500 XXXXA XXXX indicates the code meeting Ford specification ESR M2P100 C Follow the application instructions on the product Be sure to remove aggressive particles such as bird droppings tree resins insect remains tar spots and road salt that may damage your paint Cleaning the wheels Wash the wheels with the same detergent used to clean the body of your vehicle Do not use acid based wool cleaners steel wool fuel or strong detergents Never use abrasives that will damage the finish of special wheel surfaces Use a tar and road oil remover to remove grease and tar Cleaning plastic parts Some of the vehicle s trim parts are plastic Clean with a tar and road oil remover if necessary Use a vinyl cleaner for routine cleaning Do not clean plastic parts with thinners solvents or petroleum based cleaners 176 Cleaning the instrument panel Any cleaner or polish that increases the gloss of the upper portion of the instrument panel should be avoided The dull finish in this area is to help protect the driver from windshield reflection Cleaning the exterior lamps Do not use dry paper towels chemical solvents or abrasive cleaners to clean the lamps these products may cause scratches or crack the lamps Cleaning t
49. f a child safety seat refer to Children and infant or child safety seats later in this chapter 57 Seating and safety restraints Using the automatic locking mode The automatic locking mode must be used when installing an aftermarket child safety seat in any outboard passenger seat 1 Buckle the combination lap and shoulder belt 2 Grasp the shoulder belt portion and pull downward until the entire belt is extracted 3 Allow the belt to retract As the belt retracts you will hear a clicking sound This indicates that the safety belt is now in the automatic locking mode Canceling the automatic locking mode Disconnect the combination lap and shoulder belt and allow it to completely retract This will cancel the automatic locking mode and activate the vehicle sensitive emergency locking mode 58 Seating and safety restraints Front seat safety belt height adjustment Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder e To lower the height of the shoulder belt Push the button down Slide down e To raise the height of the shoulder belt Slide up Pull down on the height adjustment assembly to make sure it is locked in place Lap belt A lap belt is located in the center of the rear seat Adjusting the lap belt Because the lap belt does not have a retractor to automatically adjust itself during vehicle movement the lap belt should be
50. ft side of the engine compartment The catalytic converter enables the vehicle s emission control system to operate properly Follow these guidelines to ensure proper emission system operation e Use only unleaded fuel e Avoid running out of fuel e Do not turn off the ignition while your vehicle is in motion e Have maintenance performed according to the intervals in the Service Guide If you notice one or more of the following the emission system may not be working properly have the vehicle serviced as soon as possible e fluid leaks 571 E E lights illuminate in the instrument cluster and remain lit e strange odors 157 Maintenance and care e engine runs more than five seconds after shut off or engine misfires surges stalls or backfires e loss of oil pressure Important emission control information By law anyone who manufactures repairs services sells leases or trades vehicles or who supervises a fleet of vehicles is not permitted to intentionally remove an emission control device or prevent it from working Do not make any unauthorized changes to the vehicle or engine Changes that cause more unburned fuel to reach the exhaust system can increase the temperature of the engine or exhaust system When your vehicle is serviced never use a metal exhaust collector The use of a metal collector may melt or deform plastic parts A Do not park idle or drive your vehicle i
51. g the key and turning the ignition to ON The system will not disarm by using the key in any door trunk lock cylinder 51 Controls and features Disarming a triggered system Press either the UNLOCK or PANIC button to disarm a triggered anti theft system A triggered system can also be disarmed by Inserting the key and turning the ignition to ON This device complies with Part 15 of the FCC rules Operation is subject to the two following conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Replacement batteries for the remote entry and or anti theft system transmitters can be purchased at pharmacies watch stores or at authorized dealers If a transmitter is lost a new one may be programmed by your dealer Take any remaining transmitters with you to the dealer so they may be reprogrammed The system will work with up to four transmitters Your vehicle comes equipped with two transmitters additional transmitters can be ordered from your dealer It will be necessary to have all of the transmitters programmed to the remote entry system by the dealer at the same time 52 FRONT SEATS Lift handle to slide the seat forward or backward Lift to adjust the seatback Seating and safety restraints 53 Seating and safety restraints Head restraints Push the release
52. g or servicing your vehicle Here are some general precautions for your safety 124 e Never get under a vehicle that is supported only by a jack If you must work under a vehicle use safety stands Keep all lit cigarettes and other smoking materials away from the battery and all fuel related parts Working with the engine off 1 Set the parking brake and make sure that the gearshift is securely latched in P automatic transaxle or first gear manual transaxle 2 Turn the engine off and remove the key from the ignition Maintenance and care 125 Maintenance and care 3 Block the wheels to prevent the vehicle from moving unexpectedly 126 Maintenance and care Working with the engine on 1 Set the parking brake and make sure that the gearshift is securely latched in P automatic transaxle or N manual transaxle 2 Do not work on a vehicle in an enclosed space with the engine running 127 Maintenance and care 3 Block the wheels to prevent the vehicle from moving unexpectedly 4 If work must be done with the engine running avoid wearing loose clothing or jewelry that could get caught in moving parts Take appropriate precautions with long hair Opening the hood 1 Inside the vehicle pull the hood release handle located under the bottom left corner of the instrument panel 2 Outside the vehicle release the auxiliary latch located under the center of the ho
53. gasolines labeled as regular in high altitude areas that are sold with octane ratings of 86 or even less Do not be concerned if your vehicle sometimes knocks lightly However if it knocks heavily under most driving conditions on the recommended octane fuel see your dealer or a qualified service technician to prevent any engine damage Fuel Quality If you are experiencing starting rough idle or hesitation problems try a different brand of fuel If the condition persists see your dealer or a qualified service technician The American Automobile Manufacturers Association AAMA issued a gasoline specification to provide information on high quality fuels that optimize the performance of your vehicle We recommend the use of gasolines that meet the AAMA specification if they are available It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high quality fuel Cleaner Air Ford approves the use of gasolines to improve air quality including reformulated gasolines that contain oxygenates such as a 156 Maintenance and care maximum of 10 ethanol or 15 MTBE There should be no more than 5 methanol with cosolvents and additives to protect the fuel system WHAT YOU SHOULD KNOW ABOUT THE EMISSION CONTROL SYSTEM For more information on your vehicle s emission control system see the Vehicle Emission Control Information Decal located on the inside le
54. he wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear 12 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate 148 Maintenance and care Traction AB C The traction grades from highest to lowest are A B and C they represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance N The traction grade assigned to this tire is based on braking straightahead traction tests and does not include cornering turning traction Temperature A B C The temperature grades are A the highest B and C they represent the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life Excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal
55. he engine A clean engine is more efficient than a dirty one because a buildup of grease and dirt acts as an insulator and keeps the engine warmer than normal Follow these guidelines to clean your engine e Take care when using a power washer to clean the engine The high pressure fluid could penetrate sealed parts and cause damage In order to avoid cracking the engine block or fuel injection pump do not spray these components with cold water The alternator and air intake must be covered to prevent water damage when cleaning the engine Never wash or rinse the engine while it is running water in a running engine may cause internal damage Maintenance and care 177 Maintenance and care Cleaning the wiper blades If the blades do not wipe properly clean both the windshield and the wiper blades using undiluted windshield washer solution or a mild detergent Rinse thoroughly with clean water Do not use fuel kerosene paint thinner or other solvents to clean the wiper blades these fluids will damage the blades Cleaning the built in child seat Clean the built in child seat with mild soap and water Do not use household cleaning products because they may weaken the safety belt webbing or damage the vinyl parts of the seat The child seat liner is removable and may be machine washed and air dried Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommende
56. he wagon is similar although the bulb replacement process differs For more information see Tail lamps Backup lamps in this section In addition the headlamp assembly includes the headlamp and the turn signal parking lamp assemblies Do not remove lamp bulbs unless they may be replaced immediately with new ones If a bulb is removed for an extended period of time contaminants may enter the lamp housings and affect performance A Handle a halogen bulb carefully and keep out of children s reach Grasp the bulb only by its plastic base and do not touch the glass the oil from your hand could cause the bulb to break the next time that the headlamps are operated 161 Maintenance and care Headlamps To change the headlamp bulbs 1 Be sure that the headlamp knob is in the OFF position 2 Open the hood and find the headlamp socket 3 Remove the protective dust shield housing by turning the shield counterclockwise 4 Remove the bulb retaining ring by rotating it counterclockwise when viewed from the rear 5 Disconnect the electrical connector and remove the bulb by pulling it straight out 6 Replace the bulb by pushing a new one straight in with the bulb s plastic base facing upward You may need to turn the bulb slightly to align the grooves in the plastic base with the tabs in the bulb socket 7 Slip the bulb retaining ring over the plastic base and lock the ring by rotating it clockwise until i
57. headlamp may be properly aimed in the horizontal direction and the vertical direction by performing the following steps The horizontal aim must be adjusted first This procedure requires the use of a 4 mm box wrench or open end wrench Position the vehicle on a surface that is level in the front to rear direction If the vehicle cannot be placed on a true level surface the headlamps still can be adjusted using the VHAD if the slope of the surface is accurately known and does not differ by more than 30 5 mm 1 2 in from true level 173 Maintenance and care Adjusting the horizontal aim 1 With the hood open locate the horizontal indicator and adjusting screw 2 Use a 4 mm wrench to turn the horizontal adjusting screw until the reference mark on the reflector extension aligns with the O reference mark on the horizontal indicator when viewed directly from above 3 When the horizontal aim has been adjusted close the headlamp access panel Adjusting the vertical aim 1 Do not adjust the vertical aim until after adjusting the horizontal aim 2 With the hood open locate the bubble level vertical aim indicator It is visible when viewed from above the rear of the headlamp 3 With the vehicle on a level surface use a 4 mm wrench to turn the vertical aim adjustment screw outboard screw located on the back of the lamp assembly clockwise or counterclockwise until the bubble in the spirit level
58. icing while towing If you tow a trailer for long distances your vehicle requires more frequent service than a vehicle not used for towing Refer to the Service Guide for more information 105 Driving Towing behind a recreational vehicle RV Do not tow your vehicle behind another vehicle such as an RV unless front wheel dollies are used Luggage rack if equipped Load luggage as far back as it will safely go on the rack without causing the vehicle to exceed the gross vehicle weight rating GVWR or gross axle weight rating GAWR FUEL CONSUMPTION Fuel economy can be improved by avoiding e lack of regular scheduled maintenance excessive speed rapid acceleration driving with the brake pedal depressed sudden stops extended engine idling use of speed control in hilly terrain e extended use of the air conditioner defroster rear window defroster and other accessories e underinflated tires e heavy loads e aftermarket add ons such as bike ski or luggage racks bug deflectors etc 106 Roadside emergencies USING THE HAZARD SWITCH Use the hazard flashers to warn traffic of vehicle problems e Slide the hazard switch to the right to activate the hazard flashers e Slide the hazard switch to the left to deactivate the continuously blinking flashers RESETTING THE FUEL PUMP SHUT OFF SWITCH The fuel pump shut off switch stops the fuel pump when the vehicle has b
59. icle For more information on warning light illumination refer to Preparing to start the vehicle in the Starting chapter Warning chimes Safety belt warning chime For information on the safety belt warning chime refer to the Seating and safety restraints chapter Supplemental restraint system SRS warning chime For information on the SRS warning chime refer to the Seating and safety restraints chapter 10 Instrumentation Key in ignition warning chime A warning chime sounds when the key is left in the ignition and any door is opened Headlamps on warning chime A warning chime sounds when the headlamps are on the ignition is off and a door is opened 11 Instrumentation Instrument cluster gauges Base cluster gauges 140 100100 olololololo Sport cluster gauges 12 Instrumentation Speedometer Fuel gauge When the fuel gauge needle is on the E empty portion of the yw 7 gauge there are between E F approximately 2 L 6 gallons and 4 L 1 gallon of usable fuel left in the tank Engine coolant temperature gauge If the engine coolant temperature gauge moves into the H zone gx 1 Pull off the road as soon as is safely possible 2 Turn off the engine and let it cool 3 Check and add engine coolant as necessary Refer to Checking and adding engine coolant in the Maintenance and care chapter If the coolant level and mixture is
60. ing the air 19 Controls and features conditioning can only function if the air temperature outside the vehicle is about 10 C 50 F or higher Select A C and turn the temperature dial to the left for recirculated cooled airflow through these vents Using the panel mode e This brings in outside air and can be used for heating and ventilating Select Av for airflow through these vents Using the floor mode In the OFF mode outside air is shut out and the fan will not operate Using the panel floor mode Manual heating system e This mode brings in outside air and can be used for heating and ventilating Manual heating and air conditioning system lt P e This mode brings in outside air and can be used for heating ventilating or air conditioning the air conditioning can only 20 Controls and features function if the air temperature outside the vehicle is about 10 C 50 F or higher Select this mode for airflow through these vents Using the floor mode In this mode with the temperature control knob between full cool and full hot ranges slightly warmer air will be directed toward your feet and cooler air toward your chest In the full cool or full hot ranges the airflow toward both feet and chest will be the same temperature e This allows for maximum heating but can also be used for ventilating Select for airflow through the rear seat floor ducts and the
61. ion and instructions refer to Guarding against exhaust fumes in this chapter 85 Starting PREPARING TO START THE VEHICLE Engine starting is controlled by the spark ignition system This system meets all Canadian Interference Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise Before starting the vehicle 1 Make sure all vehicle occupants have buckled their safety belts F or more information on safety belts and their proper usage refer to the Seating and safety restraints chapter 2 Make sure the headlamps and vehicle accessories are off If starting a vehicle with an automatic transaxle e Make sure the parking brake is set 86 Starting If starting a vehicle with an automatic transaxle e make sure that the gearshift is in P If starting a vehicle with a manual transaxle e push the clutch pedal to the floor e place the gearshift in the neutral position 87 Starting 4 Turn the key to the ON position without turning the key to START Make sure the following lights illuminate briefly If a light fails to illuminate have the vehicle serviced If the driver s safety belt is fastened the A light does not illuminate STARTING THE VEHICLE After completing the steps under Preparing to start the vehicle 1 Turn the key to START and release Do not press the accelerator e The key will return to the ON pos
62. ion nsssccccreece 11 Safety belt oo cee 10 Washer fluid cceeseesereeeees 134 I 1 1 gt 10 seiak inariana 135 windshield sssscccccceress 30 Windows One tOUCN GOWN oo eeeeeeeeeees 35 power windows operating 34 Windshield WASNING cceeeceteteeeeteettettetetees 30 Windshield washer fluid and wipers checking and adding fluid 134 checking and replacing wiper Blades serrano 146 liftgate reservoir escccces 135 Operation miiia 30 Wrecker towing eseese 123 Filling station information Fuel UNLEADED FUEL ONLY Octane 87 Fuel tank capacity 48 0 L 12 7 gallons Engine oil Use only engine oil displaying the American Petroleum Institute Certification Mark SAE 5W30 is preferred Tire size amp pressure Refer to Tire Pressure Decal on passenger s door pillar Hood release Pull handle under the left side of the instrument panel 192
63. ion with something that will move or deform and according to the angle of impact The air bag is not designed to inflate in rollovers side impacts or rear impacts Air bags and air bag equipped vehicles should be disposed of only by qualified service personnel using Ford approved procedures The system consists of two parts 63 Seating and safety restraints The driver air bag in the middle of the steering wheel and the passenger air bag above the glove compartment The electrical system made up of impact sensors a diagnostic module and a backup power supply The air bags inflate within a fraction of a second after air bag sensors detect a severe frontal collision Gas generators within the air bags fill the air bags with a non toxic non flammable gas After the vehicle occupants have impacted the air bags the gas empties through holes in the air bags and the air bags deflate You may notice smoke and smell the escaping gas after the air bags deflate This is normal You and your passenger must wear your safety belts in order for the air bag system to operate effectively AIR BAG WARNING LIGHT AND WARNING CHIME When you turn the ignition key to the ON position the air bag system performs a self check of the e air bag sensors e air bag module e air bag inflators e available battery power e air bag warning light Following a successful system self check the Af
64. ition 2 After idling for a few seconds apply the brake and release the parking brake 88 Starting Special conditions when starting Starting a cold engine At temperatures 12 C 10 F and below do not hold the key in the START position longer than 15 seconds If the engine does not start on the first attempt 1 Turn the ignition key to LOCK and wait approximately ten seconds 2 Try starting the engine again At temperatures above 12 C 10 F do not hold the key in the START position longer than five seconds If the engine does not start on the first attempt 1 Turn the ignition key to LOCK and wait approximately five seconds 2 Try starting the engine again Starting a warm engine Do not hold the key in the START position longer than five seconds If the engine does not start on the first attempt 1 Turn the ignition key to LOCK and wait a few seconds until the starter stops 2 Try starting the engine again Starting the engine after two failed attempts If the engine does not start after two attempts 1 Turn the key to LOCK and wait about two minutes 89 Starting 2 Press the accelerator all the way to the floor and hold 3 Turn the key to START Release it once the engine starts 4 Release the accelerator gradually as the engine speeds up If the engine still does not start refer to Fuel pump shut off switch in the Roadside emergencies chapter Using the
65. king brake e the headlamp system is in the OFF position 26 Controls and features The daytime running light DRL system will not illuminate the tail lamps and parking lamps Turn on your headlamps at dusk Failure to do so may result in a collision High beams and flash to pass Push for high beam headlamp A operation Pull and release quickly for flash to pass operation Ba lt a gt Foglamps if equipped Rotate the switch to turn the foglamps on and off gt DH DED Cie o Speed control if equipped Maintain vehicle speed at least 50 km h 30 mph to operate the speed control system 27 Controls and features Press the ON portion of the ON OFF button to turn on Press the OFF portion of the ON OFF button to turn off Press the RSM button to resume a set speed Hold the SET ACC portion of the SET ACC CST button to set the desired speed Hold SET ACC to increase speed tap to increase speed in 1 6 km h 1 mph increments Hold the CST portion of the SET ACC CST button to decrease speed tap to decrease speed tap to decrease speed in 1 6 km h 1 mph increments Speed control can be canceled by pressing the brake pedal or clutch pedal if equipped Do not shift into N automatic transaxle or neutral manual transaxle with the speed control on Use only Federal Communications Commission FCC or Canadian Radio and Telecommunications Commission CRTC a
66. l equipment and cargo The GVWR is specific to each vehicle and is listed on the Safety Compliance Certification Label on the driver s door pillar 101 Driving e GAWR Gross axle weight rating carrying capacity for each axle system front and rear This amount is specific to each vehicle and is listed on the Safety Compliance Certification Label on the driver s door pillar Payload Gross vehicle weight rating Base curb weight To obtain correct weights try taking your vehicle to a shipping company or an inspection station for trucks Do not use replacement tires with lower weight capacities than the originals because they may lower the vehicle s GVWR and GAWR limitations Replacement tires with a higher weight limit than the originals do not increase the GVWR and GAWR limitations If the GVWR or the GAWR specified on the Safety Compliance Certification Label is exceeded your vehicle may be damaged or you may lose control and cause injury Trailer towing Your vehicle is capable of towing a trailer up to 454 kg 1000 Ib gross trailer weight with a maximum tongue load of 45 kg 100 Ib The trailer should have 18 6 m 20 ft or less frontal area Do not exceed the maximum loads stated on the Safety Compliance Certification Label For load 102 Driving specification terms found on the label refer to Loading your vehicle in this chapter Remember to figure in the tongue load of your load
67. low all of the manufacturer s instructions included with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision When installing a child safety seat e use the correct safety belt buckle for that seating position e make sure the tongue is securely fastened in the buckle e keep the buckle release button pointing up and away from the safety seat with the tongue between the child seat and the release button to prevent accidental unbuckling place seatbacks in the upright position 67 Seating and safety restraints put the safety belt in the automatic locking mode Refer to Using the automatic locking mode in this chapter Installing child safety seats in combination lap and shoulder belt seating positions 1 Position the child safety seat in p a seat with a combination lap and shoulder belt G If you choose to install a child N safety seat in the front passenger LN seat move the seat as far back as SOT possible 2 Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together 68 Seating and safety restraints 3 While holding the shoulder and lap belt portions together route the tongue through the child seat according to the child seat manufacturer s instructions Be sure the belt webbing is not twisted 4 Insert the belt tongue into the proper buckle until yo
68. luggage compartment lamp safety belt warning chime radio power 14 Engine 15 amp Engine control system 15 Mirrors 5 amp Power mirrors 16 Not used 17 Not used 18 Fog 10 amp Daytime running lamps fog lamps 19 Not used 20 Cigar 20 amp Cigar lighter 21 Radio 15 amp Radio Premium sound 112 Roadside emergencies Engine compartment fuse panel ia or a2 USE THE DESIGNATED FUSES ONLY Number Fuse amperage rating Circuits protected 1 Fuel injection 30 amp Fuel injection system air bags 2 Defog 30 amp Rear window defroster 3 Main 100 amp Overall circuit protection 113 Roadside emergencies Number Fuse amperage Circuits protected rating 4 BIN 40 amp Passenger compartment fuses 1 2 6 12 13 7 5 ABS 60 amp Anti lock brake system ABS 6 Cooling fan 40 amp Cooling fan 7 Head Head lamp relay 8 Not used 9 OBD II 10 amp On board diagnostics 10 Fuel pump 20 amp Fuel pump 11 Head RH 20 amp Passenger side headlamps 12 Head LH 20 amp Driver side headlamps CHANGING THE TIRES Temporary spare tire information The temporary spare tire for your vehicle is labeled as such It is smaller than a regular tire and is designed for emergency use only AN If you use the temporary spare tire continuously or do not follow these precautions the tire could fail causing you to lose co
69. ment s 177 OXEONOM es cseaiateiseeheedeecniess 177 instrument panel ou 177 plastic parts woe 176 Safety belts cece 178 WASIING oeren 175 WAXING cssecceccsccsecsssrssesssersersenes 175 Wheels sce chisdotiensidas 176 wiper blades c eee 178 Climate control system 17 air conditioning cseeseceseesseeees 19 air distribution dial 0 0 19 temperature dial lessees 18 Clutch iUe E E E ibeextsels 134 CONOIS sdrisieie ects 15 31 36 39 40 steering COLUMN scce 25 Daytime running light system 26 Defects reporting escenes 186 Disabled vehicle see Towing 123 Driving under special conditions towing a trailer 105 Emergencies roadside n 107 Emission control system 157 158 ENGINE heisser 129 182 check engine warning light 7 Engine block heater 91 Engine coolant checking and adding 5 136 low coolant warning light 10 Index ENGine Ol s isiivsaviiiwincinies 130 check oil warning light se 9 checking and adding 4 130 oa TUIMOS wis ccetertasieastencesvetes 91 ENSE fuentes ste 18 Fasting the lights ccceeeeeen 27 Floor MALS veces 39 FOQIAIMPS saina 27 163 Fuel GaPaCity soora ia 179 improving fuel economy 106 low fuel warning light seses 7 safety information relating to automotive fuels oc 153 Fuel pump shut off switch 43 107 starting after a collision 43 Fuse panels engine compartment ness 11
70. ment that was in effect when this guide was approved for printing Ford may discontinue models or change specifications or design without any notice and without incurring obligation Instrumentation Exterior lamps and Engine coolant Tachometer if turn signal lever temperature gauge equipped pg 26 and pg 1 Speedometer P9 14 pg 9 Fuel gauge Foglamp switch pg 13 Pea 09 27 Warning lights Pa Wiper washer Instrument panel lever 30 dimmer switch Rear con te pg 15 Power mirrors p control if Speed control f equipped pg equipped if equipped pg 16 pg 27 Instrumentation Refer to Audio Guide electronic stereo radio with cassette shown others available pg 17 Vents pg 18 Rear window defroster if Climate controls equipped pg 24 pg 17 if equipped with air conditioning Instrumentation INSTRUMENT CLUSTERS Instrument cluster lights Base cluster lights Sport cluster lights Base cluster lights Sport cluster lights Low fuel IIluminates when the fuel tank is almost empty approximately 8 liters 2 gallons remain The lights will also briefly illuminate when the ignition key is turned to ON and the engine is off Service engine soon IIluminates when the engine s emissions control system requires service The light will also illuminate and will remain illuminated when the ignition key is turned to ON and the engin
71. n dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Preparing your vehicle for inspection maintenance I M testing In some localities it may become a legal requirement to pass an I M test of the on board diagnostic 158 Maintenance and care OBD II system If the vehicle s powertrain system or battery has just been serviced the OBD II system is reset to a not ready for I M testing condition To ready the OBD II system for I M testing the law specifies that a minimum of 30 minutes of city and highway driving is necessary as described below e At least twenty minutes driving in stop and go city type traffic with at least four idle periods e At least ten minutes of driving on an expressway or highway Before completing the above driving modes the engine must be warmed up and at operating temperature Once started the vehicle must not be turned off during these modes 159 Maintenance and care EXTERIOR LAMPS REPLACING THE EXTERIOR BULBS Check the operation of the following lamps frequently e headlamps e foglamps if equipped e high mount brakelamp e license plate lamp e tail lamps backup lamps e interior overhead lamp 160 Maintenance and care e hazard flasher The overview of your vehicle s exterior lamps shows the tail lamp backup lamp assembly for the sedan model only The lamp assembly for t
72. n snugly against the child s shoulders Canceling the automatic locking mode on the built in child seat 1 Disconnect the chest clip Press the buckle release button and remove both safety belt tongues from the buckle 2 Slide both shoulder belts from the child s shoulders and arm and allow them to retract fully 81 Seating and safety restraints Removing your child from the built in child seat 1 Disconnect the chest clip by squeezing the release tabs together and pulling the two sides apart 82 Seating and safety restraints 2 Press the release button on the buckle 3 Slide the shoulder belts off the child s shoulders and remove the child 4 Return the child seat cushion to the stowed upright position 5 Ensure the shoulder belts are in the center of the built in child seatback and connect the cushion retention clip 6 Fold the child seat into the seatback and tuck the top of the child seat under the rear seat flap 7 Press firmly on the center of the built in child seat to ensure it is stowed properly When not in use the built in child seat can be stowed so that the rear center seat position may be used or the rear seatback can be folded down 83 Seating and safety restraints Inspecting the built in child seat after a collision All built in child restraints including seats buckles retractors seat latches interlocks and attaching hardware should be inspect
73. ndow on each tongue is green to ensure proper safety belt connections 79 Seating and safety restraints If both tongues do not latch in the buckle do not use the child seat See your dealer for repairs 8 Fasten the left and right chest clip halves together to hold the shoulder belts in place comfortably on the child s shoulders Verify that the indicator window on the chest clip is green to ensure a proper chest clip connection e When either of the tongues or the chest clip is unbuckled the red color appears in the window The chest clip is designed to pull apart easily in the event of collision The clip helps keep the belts on the shoulders of a squirming or sleeping child 9 Pull on the safety belt tongues to ensure they are both securely latched If they are not latched repeat steps seven and eight If necessary the shoulder belts can be put in the automatic lock mode to limit the child s movement in the child seat The mode may be used if the child is sleeping or attempting to get out of the child seat If not placed in an automatic locking mode the child seat shoulder belts are in the vehicle sensitive emergency locking mode which locks the shoulder belt in the event of a crash hard braking or hard cornering 80 Seating and safety restraints Activating the automatic locking mode on the built in child seat 1 Fully pull out both shoulder belts 2 Allow the belts to tighte
74. ntrol of the vehicle possibly injuring yourself or others When driving with the temporary spare tire do not 114 Roadside emergencies exceed 80 km h 50 mph under any circumstances load the vehicle beyond the maximum vehicle load rating listed on the Safety Compliance Certification Label use tire chains drive through an automatic car wash because of the vehicle s reduced ground clearance try to repair the temporary Spare tire or remove it from its wheel use the wheel for any other type of vehicle Tire changing procedure I 2 3 4 automatic transaxle or R manual transaxle Park on a level surface Activate the hazard flashers Set the parking brake Place the gearshift in P e Automatic 115 Roadside emergencies e Manual 5 Block the diagonally opposite wheel e Remove the lug wrench first Use the lug wrench to remove the hold down bolts on the spare tire and jack 116 y Roadside emergencies 6 Remove the jack jack handle and spare tire from the vehicle s rear cargo area e Locate the wheel cover hold down lug nut Completely remove this lug nut Use the lug wrench provided with the jack to loosen the retention bolts on the spare tire Do not attempt to remove the wheel cover until lug nuts are removed 117 Roadside emergencies 7 Loosen the remaining wheel lug nuts with the lug wrench about one half turn counterclockwise 8 Posi
75. od 3 Lift the hood and secure it in the open position with the prop rod 4 To close the hood remove the prop rod and shut so that the auxiliary latch is closed After closing the hood try to lift it to be sure that it is closed securely 128 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT WOMWNHUBRWNE i b Z Orea eG NSS J al CREENA O SRRA SSSA Tow CUNT PA i N P Y Xz Y A RAS een A M a AS Q pms D A CRE NS lA g Paar VA y A SD Engine oil dipstick Engine oil filler cap Brake fluid reservoir Windshield washer fluid Coolant reservoir Steering fluid reservoir Automatic transmission dipstick Battery Air filter assembly 129 Maintenance and care CHECKING AND ADDING ENGINE OIL Use SAE 5W 30 motor oil CERTIFIED FOR GASOLINE ENGINES by the American Petroleum Institute Look for the certification Ford specification WSS M2C153 F Additional engine oil additives oil treatments or engine treatments are never needed and could under certain conditions lead to engine damage which is not covered by your Warranty Changing the engine oil and oil filter Change the engine oil and oil filter per the following whichever occurs first 5 000 MILES 8 000 KM OR 6 MONTHS NORMAL SCHEDULE 3 000 MILES 5 000 KM OR 3 MONTHS SEVERE DUTY SCHEDULE EXTENSIVE IDLING T
76. og IAMPS peresan 27 163 headlamps nsee 26 162 Nigh DEAMS pisima 27 high mount brakelamp 164 illuminated entry system 33 interior AMPS veces 31 170 map LAMPS users 31 171 replacing DUIDS oo 160 tail IAMPS oo cesses 167 168 License plate lamps nesese 165 Liftgate ee eceseeeeeeeseeeereees 40 164 warning MORE serisinin 10 Lights warning and indicator 6 OMe DAG E E E 7 64 anti lock brakes ABS nsss 9 anti theft scrii iiinis 9 EEE EE 8 charging System 0 cee 9 checkcoolant ssssssrssre 10 high beani saisaitia 9 liftgat amp djar saci cissccacaseaccecsssesazaves 10 MONE e AE T 7 Oil PFESSULE sirmonissnisiinisin 9 Safety Delt oo eeeeseseeeteeeeees 8 service ENGINE SOON nesese 7 turn signal indicator eses 9 upshift indicator oo 8 Load liMItS scssiiiisisiwrisrreriesa 101 GVWR scesnsainosinnasinian 101 trailer tOWING sescscscreres 102 Lubricant specifications 180 LUGGAGE LACK psasirrarsiis 106 Manual transaxle cece 99 ANNIN rcason 99 fluid checking and adding 134 shifting GOALS eecesesseeeeeeeeees 100 Mirrors side view mirrors power 16 Motorcraft parts scerenieiuenis 179 National Highway Traffic Safety Administration ss 186 Parking Drake ceecceeseesseeeees 94 automatic release oe 38 operation ireira asan 94 warning light ssreiserunaias 8 Parts see Motorcraft Parts 179 Power door IOCKS wissen 31 Power features COOP OGKS serenita 31 WINK
77. on on the hazard flasher and hazard switch refer to Using the hazard switch in the Roadside emergencies chapter For bulb replacement see your dealer or a qualified service technician 171 Maintenance and care BULB SPECIFICATIONS Function Number of Trade number bulbs Exterior illumination Front park turn lamps 2 3457 Foglamps if equipped 2 881 Headlamps aero high and low 2 9007 beam Rear license plate lamp 2 168 High mount brakelamp 1 921 Notchback Backup lamp 2 3156 Notchback Brakelamp 2 3157 Notchback Rear turn side 2 3157 marker Liftgate wagon rear side marker 2 168 lamp 1 each side Interior illumination Cargo lamp liftgate wagon 1 12V 5W Interior overhead lamp 2 12V 10W Luggage compartment lamp if 1 5W equipped PRNDL illumination 1 197 Heater control nomenclature 1 14V 3 0 High beam indicator 1 W Instrument panel gauge cluster 4 194 Sport cluster w tachometer 2 194 Turn signal indicator 1 194 Upshift indicator if equipped 1 each 194 Warning lights all 194 172 Maintenance and care Function Number of Trade number bulbs Anti theft LED 1LED See your dealer to order replacement assembly service part 57Z13B765 A Aiming the headlamps Your vehicle is equipped with a variable headlamp aiming device VHAD on each headlamp reflector extension and headlamp housing Each
78. or any engine coolants mixed with alcohol or methanol antifreeze Do not use supplemental coolant additives in your vehicle These additives may harm your engine cooling system The use of an improper coolant may void the warranty of your vehicle s engine cooling system Recycled Engine Coolant Ford Motor Company recommends that Ford and Lincoln Mercury dealers use recycled engine coolant produced by Ford approved processes Not all coolant recycling processes 137 Maintenance and care produce coolant which meets Ford specification ESE M97B44 A and use of such coolant may harm engine and cooling system components Always dispose of used automotive fluids in a responsible manner Follow your community s regulations and standards for recycling and disposing of automotive fluids Coolant Refill Capacity To find out how much fluid your vehicle s cooling system can hold see Refill capacities for fluids in the Index Have your dealer check the engine cooling system for leaks if you have to add more than a quart liter of engine coolant per month Severe Winter Climate If you drive in extremely cold climates less than 34 F 36 C it may be necessary to increase the coolant concentration above 50 Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in which you drive during winter months Never
79. or use with child safety seats However attachment holes at each rear seating position have been provided in your vehicle to attach the anchor hardware if required Kits can be obtained at no charge from any Ford or Lincoln Mercury dealer A Only use the tether attachment hole locations shown The tether anchor may not perform properly if the wrong mounting location is used Ford recommends using child safety seats with a top tether strap designed to secure an aftermarket child safety seat in the front or rear seating position Follow the child safety seat manufacturer s instructions for installing a child safety seat with a tether strap 72 Seating and safety restraints Ford recommends you attach tethered safety seats in a rear seating position with the tether strap attached to the tether anchoring bracket as shown in the instructions provided with the tether anchor kit If a tethered seat must be installed in the front passenger seat 1 Install the child safety seat in the front passenger seat For instructions on how to install the seat refer to Installing child safety seats in combination lap and shoulder belt seating positions in this chapter 2 Hook the tether strap clip to the tongue of the rear center lap belt and ensure that the belt is pulled tight To install a child safety seat using a tether strap in the back seat 1 Install the child safety seat in the rear right left or center seat po
80. ove the fuse panel cover To reset a circuit breaker press the reset button The HEATER 30A circuit breaker controls the vehicle s heater The circuit breaker is located just above and to the left of the instrument panel fuse panel To reset a circuit breaker press the reset button 110 Roadside emergencies Fuse rating Color 10 amp Red 15 amp Blue 20 amp Yellow 30 amp Light Green 30 amp fuse link Pink 40 amp Green 60 amp fuse link Yellow 80 amp fuse link Black 100 amp fuse link Blue Instrument panel fuse panel Number Fuse amperage Circuits protected rating 1 Stop 15 amp Brakelamps shift lock 2 Tail 15 amp Instrument cluster illumination license plate lamp parking lamps side marker lamps tail lamps radio climate control illumination 3 Sun roof Not used 4 ASC 10 amp Speed control y Not used 6 Door lock 30 amp Power door locks 7 Horn 15 amp Horn 8 Air Conditioning 15 amp AIC clutch 111 Roadside emergencies Number Fuse amperage Circuits protected rating 9 Meter 10 amp Backup lamps shift lock gauges speed control turn signals key in ignition reminder chime 10 Wiper 20 amp Windshield wipers and washer 11 Rear wiper 10 amp Rear wiper and washer 12 Hazard 15 amp Hazard flashers turn signals 13 Room 10 amp Clock interior lamp
81. pproved radio transmitting equipment in your vehicle to prevent speed control malfunctions 28 Tilt steering if equipped Pull the lever down to adjust the steering column angle Push the lever back up to lock the steering wheel in position AN Never adjust the steering wheel when the vehicle is moving You could lose control of the vehicle and injure someone Hazard flasher switch For information on the hazard flasher switch refer to the Roadsi de emergencies chapter Controls and features 29 Controls and features Windshield wipers and washer Wipers Rotate the windshield wiper switch to the desired interval position Push up and release to wipe the windshield only once Pull down to select the wipers on continuously Washer Pull toward you for windshield washer fluid operation Rear window wipers and washer if equipped Wipers For rear operation rotate the rear window wiper and washer switch to the desired position Select ON Rear wiper on OFF Rear wiper and washer off Washer For rear window washer fluid operation pull toward you Select Top lt 5 Rear washer on Bottom lt 5 Brief rear wiper and washer operation for quick cleaning 30 a IST FF ON ce INT OFF 7 orr A OVERHEAD CONTROLS Overhead Lamps Move the overhead lamp switch to the desired position OFF Overhead lamp off DOOR Overhead lamp illuminates when a door is opened ON
82. r to the engine coolant recovery reservoir DO NOT ADD DIRECTLY TO THE RADIATOR Add straight water only in an emergency but you should replace it with a 50 50 mixture of coolant and distilled water as soon as possible Check the coolant level in the coolant recovery reservoir the next few times you drive the vehicle If necessary add enough of a 50 50 mixture of coolant and water to bring the liquid level to the fill line on the reservoir Never remove the coolant recovery cap while the engine is running or hot If you must remove the coolant recovery cap follow these steps to avoid personal injury caused by escaping steam or engine coolant 1 Before you remove the cap turn the engine off and let it cool 136 Maintenance and care 2 When the engine is cool wrap a thick cloth around the cap and turn it slowly counterclockwise to the first stop 3 Step back while the pressure releases 4 When you are sure that all the pressure has been released use the cloth to press the cap down turn it counterclockwise and remove it Use Ford Premium Engine Coolant E2F Z 19549 AA in Canada Motorcraft CXC 8 B or an equivalent premium engine coolant that meets Ford Specification ESE M97B44 A Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for 4 years or 50 000 miles 80 000 km Do not use alcohol or methanol antifreeze
83. rent functions are noted If equipped with air conditioning Controls and features 17 Controls and features Vents The airflow from the vents may be adjusted by moving the horizontal lever or by moving the vent up and down according to your airflow preference Operating the climate control Turn the fan speed dial to the desired speed Turn the temperature dial to the desired mix of warm and cool air left for cooler and right for warmer 18 Controls and features Turn the air distribution dial to the a desired airflow position For x DEN vehicles with manual heating OFF 7 systems the modes can only be used for heating or ventilating A C A except OFF ae te MAX To prevent humidity buildup inside A C E of the vehicle always drive with the climate control system turned on CHV Do not put objects under the front seats that interfere with the flow of air to the back seat area If equipped with air conditioning Using the MAX A C mode e MAX A C mode if equipped can be used for air conditioning or heating This mode is noisier but more economical than A C it will only function if the air temperature outside the vehicle is about 10 C 50 F or higher Select MAX A C and turn the temperature dial to the left for recirculated cooled airflow through these vents Using the A C mode e A C mode if equipped can be used for heating ventilating or air condition
84. restraints eccerre 54 split folding rear Seat wo 54 Servicing your vehicle precautions when servicing 124 servicing when you tow 105 Special driving conditions 89 Specification chart lubricants 180 Speed control vo ceeecseeeeeeeeeees 27 Starting your vehicle sss 88 preparing to start your VENICE parainen 86 starting a cold engine 89 starting a warm engine 89 Steering wheel UENO erea 29 Tail lamps bulb replacement s s s 167 168 Tilt steering wheel veces 29 Tire types sisedssicescdadeseatevtescectses 152 Tires 3 4 senancticiinancunenes 148 CHANGING snieman 114 checking the pressure 150 repla irig oo eeeeeteteeeesetetsetetsees 151 rotat esini 151 snow tires and chains 152 tire QradeS oo 148 treadWear isinsin 148 Trailer tOWING cscs 102 Safety Chains oo cece 104 UPS as osoenean 105 trailer brakes cee 104 trailer lamps diiseni 104 Tran5aXl Enararen 96 fluid checking and adding automatic ascisiisnnineissrs 139 Turn signal indicator lights asesoris 9 Upshift indicator light 8 100 Upshift speeds occ 100 Vehicle dimensions nesses 182 Vehicle headlamp aiming device VHAD ncsniararsnia 173 190 Vehicle Identification Number VIN csavcetlevchastatatiieienttacdetad 185 Ventilating your vehicle see Climate control ww 18 19 23 Warning CHIMES esseere 10 headlamps ON wees 11 key in ignit
85. rn the proper idle conditions Avoid using unneccessary electrical accessories for a short while to let the battery recharge A battery charger may be necessary to fully recharge the battery 122 Roadside emergencies WRECKER TOWING If towing is necessary it is recommended that your vehicle be towed with wheel lift or flatbed equipment Do not tow with slingbelt equipment Ford Motor Company has not developed or approved a T hook or slingbelt towing procedure 123 Maintenance and care SERVICE RECOMMENDATIONS Whenever possible Ford has designed parts that do not require servicing However when servicing is required Ford s goal is to make servicing your vehicle as easy as possible To help you e We highlight do it yourself items in the engine compartment for easy location Often parts such as the headlamp bulbs may be replaced without tools We provide you with a Service Guide that makes tracking routine service of your vehicle easy If your vehicle requires professional servicing your dealership can provide the necessary parts and service Check the Warranty Information Guide to find out what parts and services are covered Use only recommended fuels lubricants fluids and service parts conforming to Ford specifications Motorcraft parts are designed and built to provide the best performance in your vehicle Precautions for servicing your vehicle Be particularly careful when inspectin
86. se vents Using the defrost floor mode Manual heating system e This brings in outside air and can be used for heating or ventilating 21 Controls and features Manual heating and air conditioning system lt 7 e This brings in outside air and can be used for heating ventilating or air conditioning in order to dehumidify the windshield the air conditioning can only function if the air temperature outside the vehicle is about 10 C 50 F or higher Select Y for airflow through these vents Using the defrost mode Manual heating system GY e This brings in outside air and can be used for heating and ventilating and will clear ice or fog from the windshield and front side windows Manual heating and air conditioning system e This brings in outside air and can be used for heating ventilating or air conditioning in order to dehumidify the windshield the air conditioning can only function if the air temperature outside the vehicle is about 10 C 50 F or higher 22 Controls and features Select Q for airflow through these vents Special features For slightly warm airflow toward your feet and slightly cool airflow toward your chest at the same time If equipped with air conditioning For about the same temperature airflow toward your chest and feet If equipped with air conditioning For better airflow Remove snow ice and leaves from the intake vents for the
87. sition For instructions on how to install the seat refer to Installing child safety seats in lap belt seating positions in this chapter e Sedan 73 Seating and safety restraints e Wagon 2 Refer to the instructions provided with the tether anchor kit 3 Refer to the instructions provided with your child safety seat to securely attach the child safety seat by tether to the tether strap anchor location Failure to follow these precautions could increase the risk and or severity of injury in a collision BUILT IN CHILD SEAT IF EQUIPPED The rear seat may include a built in child seat This child seat conforms to all federal and Canadian motor vehicle safety standards Read the labels located on the child seat cushion and the shoulder belt for information on the built in child seat Use the built in child seat only under the following conditions At least one year old 10 27 kg 22 60 Ib Shoulders must be below the shoulder harness slots on the built in child seat Children not meeting these requirements should be secured in an approved aftermarket child seat Refer to Children and infant or child safety seats in this chapter 74 Seating and safety restraints Regularly inspect the lap and shoulder belt system of your child seat If there is any damage to the system or if it is not functioning properly see your dealer Placing your child in
88. sure everyone in your vehicle is in a seat and using a safety belt properly USING THE SAFETY RESTRAINTS PROPERLY Combination lap and shoulder belts Insert the tongue into the slot to fasten Push the red release button and remove the tongue from the slot to unfasten N The lap belts should fit snugly and as low as possible around the hips not around the waist The outboard safety restraints in the vehicle are combination lap and shoulder safety belts The front and rear seat passenger outboard safety belts have the two types of locking modes 56 Seating and safety restraints Vehicle sensitive emergency locking mode The vehicle sensitive mode is the normal retractor mode which locks the belts in response to vehicle movement For example if the driver brakes suddenly or turns a corner sharply the combination safety belts will lock to restrain forward movement of the driver and passengers The retractor can be made to lock by pulling sharply on the belt Automatic locking mode In this mode the occupant is locked in a certain position by the shoulder belt and the belt does not adjust tightness during vehicle movement The automatic locking mode is not available on the driver safety belt When to use the automatic locking mode e When a tight lap and shoulder belt fit is desired e Any time a child safety seat is installed in the vehicle For more information on the proper use o
89. t snaps 8 Reconnect electrical connector 9 Replace the housing protective dust shield and lock the shield by rotating clockwise until it locks into position 162 Maintenance and care Foglamps if equipped To change the foglamp bulbs 1 Disconnect the electrical connector from the back of the foglamp assembly 2 Twist then pull the bulb from the foglamp assembly and twist in a replacement bulb 3 Connect the electrical connector to the back of the foglamp assembly 163 Maintenance and care High mount brakelamp sedan The high mount brakelamp is located on the rear of your vehicle The brakelamp will be mounted with two fastener clips and an assembly cover on the package tray 1 Remove the push pins and cover from the package tray 2 Detach the socket from the housing and remove the bulb 3 Replace the bulb and ease the socket back into the housing 4 Replace the housing cover and secure with the push pins Liftgate lamp wagon The wagon liftgate lamp is located on the rear of the vehicle Follow these steps to replace the liftgate lamp bulb 1 Open the liftgate 164 Maintenance and care 2 To remove the liftgate lamp bulb assembly cover mounted on the liftgate s interior rear window e press in the inner portion of the two mounting screws on either oy side of the cover ey Ss e pull out the outer portion of the J mounting screws 3 Deta
90. the brakes could lock up on roads with alternating slippery and dry patches or with loose surfaces such as snow or gravel Be careful when braking 93 Driving The ABS brake system conducts a self test each time the vehicle is driven A mechanical noise may be heard while the system conducts its self test ABS warning light The light in the instrument cluster illuminates and remains illuminated if an ABS fault is detected Have your vehicle serviced by a qualified service technician as soon as possible Normal braking operation is still effective unless the 6 light is also illuminated Parking brake The parking brake should be used whenever the vehicle is parked To set the parking brake The parking brake is not designed to stop a moving vehicle However if the normal brakes fail the parking brake can be set to stop the vehicle The vehicle s stopping distance will increase greatly and vehicle steering response will be limited When the ignition is turned to ON the ey light in the instrument cluster illuminates and remains illuminated until the parking brake is released 94 Driving A If the parking brake is fully released but the Q Warning light remains on have the brakes checked immediately They may not be working properly AN Always set the parking brake fully and make sure that the gearshift is securely latched in P automatic transaxle or first gear manual transaxle
91. the built in child seat Failure to follow all of the instructions on the use of this child restraint system can result in your child striking the vehicle s interior during a sudden stop or crash Never use the built in child seat as a booster cushion with the adult safety belts A child using the adult belts could slide forward and out from under the safety belts AN The rear seatback must be fully locked before operating the child restraint system 75 Seating and safety restraints Ensure that the latch release buttons are in the full up locked position When the latch release buttons are in full up locked position and the built in child seat is open the rear seatback cannot be unlocked or folded down 1 Pull down the top portion of the child seat 76 Seating and safety restraints 2 Release the cushion retention clip 3 Lower the child seat cushion If the child seat cannot be opened return it to the dealer for repair 77 Seating and safety restraints 4 Fold the end portion of the child seat under the child seat cushion 5 Disconnect the chest clip if connected Squeeze together the release tabs on the top and bottom of the chest clip 78 Seating and safety restraints 6 Place the child in the seat and position the shoulder belts 7 Insert the left safety belt tongue into the left side of the buckle Repeat for the right side Verify that the indicator wi
92. tion the jack at the jack notch closest to the wheel 9 Insert the jack handle and raise the vehicle until the tire just clears the ground 10 Remove the wheel lug nuts and flat tire and install the spare with the temporary use label facing outward 11 Install the same metric wheel lug nuts as removed and tighten until snug 118 Roadside emergencies Installation of an English thread nut on a metric stud or vice versa will not properly secure the wheel to the hub Damaged studs may result in wheel separation and possible injury 12 Lower the vehicle and tighten the wheel lug nuts in the pattern O shown ON 13 Unblock the wheels and put the tire jack jack handle and lug wrench away 119 Roadside emergencies JUMP STARTING A DISABLED VEHICLE AN The gases around the battery can explode if exposed to flames sparks or lit smoking materials An explosion could result in injury or vehicle damage AN To protect yourself when charging a battery always shield your face and eyes Make sure that you can breathe fresh air Batteries contain sulfuric acid which burns skin eyes and clothing If the battery acid touches someone s skin eyes or clothing immediately flush the area with water for at least fifteen minutes If someone swallows acid have him or her drink lots of milk or water first then Milk of Magnesia a beaten egg or vegetable oil Consult a physician immediately
93. to open the trunk e Sedan Locking the doors Driver door only system e Press once to lock only the driver s door e Press again within five seconds to verify system has attempted to lock the door horn will sound once and parking lamps will flash The remote opens and locks the driver s door only it will not activate the other three doors A bright yellow key fob and DRIVER S DOOR ONLY label are provided with your remote entry system They provide an additional reminder that the remote entry system locks and unlocks only the driver s door If the other doors are unlocked they will remain unlocked even after the system has locked the 47 Controls and features driver s door The other doors must be locked manually e Sedan e Wagon All door system e Press once to lock all doors e Press again within five seconds to verify doors are locked horn will sound once and parking lamps will flash If a door is ajar the horn will sound twice when the LOCK button is pressed a second time with the all door system 48 Controls and features Sounding a panic alarm Press once to sound an alarm with either the driver door only or all door system e Sedan e Wagon The parking lamps flash the horn sounds and the illuminated entry system turns on Press a second time to turn off the alarm Illuminated entry Interior lamps illuminate when the UNLOCK button is pressed on the r
94. tures 1 Remove the shade from the mounting brackets by detaching the safety clip and pressure fit plastic knobs from either side of the shade Extend the shade fully with the smooth grain facing you 2 Wrap the vinyl around the tube twice by twisting the tube away from you Tuck the edges of the vinyl inside the end cap with each wrap 3 Fold the vinyl toward the center making sure the edges clear the end cap slots Use tape or a rubber band to hold the vinyl on the left side of the tube 4 Push in the right end cap marked R about 6 mm 1 4 inch to disengage the clutch and hold in while turning the tube toward you fourteen times 5 Let go of the right end cap and unfold the vinyl Place the vinyl into the end cap slots 6 Place the shade back in the vehicle A To avoid possible injury during a sudden stop or collision the cover should be attached to the brackets when not in use 42 Controls and features Fuel pump shut off switch The fuel pump shut off switch stops the fuel pump when the vehicle has been involved in a collision or substantial jolt If the vehicle does not start it is possible that the fuel pump shut off switch needs to be reset AN If you see or smell fuel do not reset the switch or try to start your vehicle Have all the passengers get out of the vehicle and call the local fire department or a towing service The fuel pump shut off switch is located in the
95. u hear and feel the latch engage Make sure the tongue is latched securely by pulling on it 5 To put the retractor in the automatic locking mode grasp the shoulder portion of the belt and pull downward until all of the belt is extracted 6 Allow the belt to retract The belt will click as it retracts to indicate it is in the automatic locking mode 69 Seating and safety restraints 7 Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down on the child seat to tighten the belt as much as possible 8 Allow the safety belt to retract to remove any slack in the belt 9 Before placing the child in the seat forcibly tilt the seat from side to side and forward and back to make sure the seat is securely held in place 10 Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode you should not be able to pull more belt out If the retractor is not locked unbuckle the belt and repeat steps two through nine e Check to make sure the child seat is properly secured before each use Installing child safety seats in the rear center seating position 1 Tip the tongue and pull to lengthen the lap belt Se Pad 2 Place the child safety seat in the A center seating position 3 Route the lap belt through the child safety seat according to the child seat manufacturer s instructions 70 Seating
96. verfill the fuel tank The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire N If you do not use a proper fuel cap the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision 154 Maintenance and care AN If the fuel cap is venting vapor or you hear a hissing sound wait until it stops before completely removing the cap CHOOSING THE RIGHT FUEL Use only UNLEADED FUEL The use of leaded fuel is prohibited by law and could damage your vehicle The damage may not be covered by your warranty Your vehicle was not designed to use fuel containing manganese based additives such as MMT Additionally vehicles certified to California emission standards indicated on the underhood Vehicle Emissions Control Information label are designed to operate on California reformulated gasolines If California reformulated gasoline is not available when you refuel your vehicle can be operated on non California fuels However even though your engine will perform adequately on other gasolines the performance of the emission control devices and systems may be adversely affected Repair of damage caused by using a fuel that your vehicle was not designed for may not be covered by your warranty 155 Maintenance and care Octane Recommendation Your vehicle is designed to use regular gasoline with an R M 2 octane rating of 87 We do not recommend
97. y are no longer needed Do not use tire chains on dry roads The suspension insulation and bumpers will help prevent vehicle damage Do not remove these components from your vehicle when using snow tires and chains WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUEL Automotive fuels can cause serious injury or death if misused or mishandled Observe the following guidelines when handling automotive fuel e Extinguish all smoking material and any open flames before fueling your vehicle e Automotive fuels can be harmful or fatal if swallowed If fuel is swallowed call a physician immediately even if no 153 Maintenance and care symptoms are apparent The toxic effects of fuels may not be evident for many hours Fuels can also be harmful if absorbed through the skin If fuel is splashed on the skin promptly remove contaminated clothing and wash skin thoroughly with soap and water If fuel is splashed in the eyes remove contact lenses flush eyes with water for fifteen minutes and seek immediate medical attention Be particularly careful if you are taking Antabuse or other forms of disulfiram for the treatment of alcoholism Breathing gasoline vapors or skin contact with fuel could cause an adverse reaction Consult a physician immediately If you replace your fuel cap with an aftermarket fuel filter cap the customer warranty may be void if any damage to the fuel tank and or fuel system occurs A Do not o

Mercedes-Benz 2011 E350 Sedan Automobile User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents