Lindy 32969 Switch User Manual
Contents
1. 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation LINDY No 32969 LINDY ELECTRONICS LIMITED amp LINDY ELEKTRONIK GMBH First Edition MAR 20032. 100x30mm 8x4x1 2 inches Power External power adapter 7 5V 0 5A Operating Temperature 32 131 F 0 55 C Operating Humidity 10 95 Noncondensing Physical Description Front and Rear Panel Collision LED Power LED f 9 Port 10Mbps N 8xUTP 1x BAC of sooaccvas Ethernet Hub S PT BNC Port Port 1 provide upulink RJ45 Connectors function by slide switch Power Connector 1 Power Indicator This LED indicator is on when the hub is powered up 2 Collision Indicator This LED indicator blinks when the hub detects a collision on the network 3 Link Activity Indicator These LEDs indicate the state of the data link When the connection is okay these LEDs remain on Blinking indicates data is being received on the segment 4 RJ 45 Ports The hub is equipped with 8 RJ 45 ports for making 10BASE T hub to work station connections 5 BNC Port Provide one BNC port for connect to thin Ethernet 10Base2 6 Slide switch Port1 is designed to provide normal or uplink function by slide switch See picture below 7 AC Adapter Port Insert the AC adapter jack into this port Left side Panel O Normali L uplink Installation 1 Operating Environment This hub must be installed and operated within limits of specified operating temperature and humidity Do not place objects on top of the unit or obstruct any vents at the sides of the hub Do not position the hub near any heating source such
3. 40VAC US 110V AC 7 5V AC 0 5A Size approx 19 x 10 x 4 cm Weight 0 2kg 0 6kg Connectors 8 x RJ 45 STP UTP 1 x BNC This equipment has been tested and found to comply with the limits for a Class B Digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions
4. LINDY COMPUTER CONNECTION TECHNOLOGY 8 1 Port 10Base T 2 Ethernet Hub User Manual English C LINDY No 32969 UNDY ELECTRONICS UMITED amp LINDY ELEKTRONIK GMBH First Edition MAR 2003 Packing List The package should contain the following items e The 8 1 Port Ethernet Hub e One AC AC Power Adapter e This User s Guide If any of the items are missing or damaged please contact your local dealer Introduction With eight UTP ports and one BNC port located at the rear panel this device allows you to network up to at least nine workstations in a standalone configuration An uplink function is designed for connection to another hub to extend your segment rather than a normal port for a workstation For more details about Uplink function refer to the following section Running at 10Mbps with great stability this hub complies with IEEE802 3 standard Features IEEE 802 3 compliant 10Mbps CSMA CD Provide one slide switch to select Port 1 to uplink mode or normal mode Provide one BNC port for connect to thin Ethernet 10Basez2 Port auto partitioning and reconnection to facilitate faulty segment isolation Data collision and jabber handling functions Two LEDs to indicate Power and Collision status Two year warranty Specifications Standards IEEE 802 3 10Mbps Ports RJ 45 x 8 BNC x 1 Hub LEDs Power Collision Port LEDs Link and Activity Dimension 187x
5. as heaters radiators or direct exposure to sun Prevent entering of water and moisture into the unit If necessary use dehumidifier to reduce humidity 2 Connecting to network devices Connect one end of the network cable to any of the RJ45 or BNC connectors on the rear panel and connect the other end of the network cable to the network device with R45 or BNC connectors and the maximum length between the hub and any network devices UTP is 100 meters 300ft and BNC is 200 meter 650ft Once the network cable is connected on both ends and the attached network devices are powered on the CJ Uplink function is designed for the extension of your segment by connecting to another hub See the illustrated figure as below Beware that the port 1 can be select to uplink function by slide switch There are two ways can let you to connect two hubs First you can switch the slide switch to uplink mode then the port1 can be uplink to another hub s normal port by using straight through twisted pair cable Second if you want to uplink to another hub s normal ports please be attention that you have to use one crossover cable Cina ol Network Adapter 100M 3 Uplink to another Hub Port 1 can be selected to normal pooo or uplink function by slide switch PEA 8 Ethernet Hub Another Hub Lietenn TO SZ Normal Port 4 Connecting the power Plug the power cable into the hub and connect it to an electrical o
6. utlet Troubleshooting 1 Power LED is not lit Check if the power cord is properly connected to the external power adapter and the power outlet Make sure the DC power jack is firmly plugged into the power socket of the hub 2 Link Status LED is not lit Check the power switch of the network devices attached to the hub make sure they are turned ON Check the network cables make sure they are properly connected to the hub and the network devices Check the network cables make sure the cables comply with EIA TIA 568 specification Use straight through Category 3 or higher cables for 10Mbps connection 3 Link Status LED is not lit when it is uplinked to another hub Check the network cable make sure it is properly connected to both hubs One end of the cable should be connected to uplink port while the other end of the cable should connected to a regular port Do not connect the cable to both uplink ports Check the network cable make sure the cable complies with EIA TIA 568 specification Use Category 3 or higher cables for 10Mbps hub connection 4 Collision LED flashes constantly Remove all the network cables connect the cables back one by one to isolate the source of the collision Check the network cable inferior cable quality will result in excessive collision and error packets Contact your dealer if problem persist Technical Data 10Base T 2 8 port STP UTP 1 Port BNC Ethernet Hub No 32969 Power Adaptor Europe 2
Download Pdf Manuals
Related Search