KitchenAid 9743822 Dishwasher User Manual
Contents
1. Keep cardboard shipping base or hardboard under dishwasher until it is installed The shipping base or hardboard will help to protect floor covering when dishwasher is moved across the floor during installation Introduction cont from page 2 Product dimensions Side view Vue de c t A 24 61cm 24 1 4 61 6 cm 61 6 cm 24 1 4 po 25 1 4 64 1 cn 64 1 cm 25 1 4 po does not include insulation blanket ne comprend pas Pisolant 19 3 4 50 2cm Built in opening Opening for electrical drain and water supply lines e Must be installed within the shaded area as specified e Should be located as close to the rear wall as possible Electrical outlet must be installed in an adjacent cabinet Wiring should not contact the motor or dishwasher legs Water line Cut 1 2 1 3cm diameter opening Water line Must Not contact the motor or dishwasher legs Drain line and power supply cord Cut 1 1 2 3 8cm diameter opening Direct wire electrical supply Cut 3 4 1 9cm diameter opening Install a grommet Part No 302797 in opening cut in a metal cabinet for power supply cord or power supply cable Dishwasher must be completely enclosed sides top and rear Side panel kits are available from your dealer for installing your diswasher at the end of a cabinet Black Part No 4378868 White Part No 4378867 Almond Part Nn 437240 It is the customer s responsibility To contact2. Do not use dishwasher until completely installed b 4 Do not push down on open door Doing so can result in serious injury or cuts WARNING Excessive Weight Hazard Use two or more people to move and instali dishwasher Failure to do so can result in back or other injury Keep cardboard shipping base or hardboard under dishwasher until it is installed The shipping base or hardboard will help to protect floor covering during installation Remove the four screws attaching access panel A and lower panel B to dishwasher using a 1 4 hex socket nut driver or Phillips screwdriver Remove panels and set panels aside on a protective surface Position See Hlustration 3 4 For additional height 1 Add shims under the wheels 2 Turn front levelers each turn is approximately 1 16 1 6mm in height Measure height of cabinet opening C from underside of countertop to floor Check chart for that height opening Put wheels D in the required position Drain hose connection Connect drain hose to an air gap or waste tee using one of the recommended or alternate methods Recommended Connection Methods Air Gap Install Air Gap Kit Part No 300096 A according to kit instructions If a different air gap is used it should be checked to make sure it allows for the same air flow Drain hose B to air gap A to waste tee C Cut drain end of drain hose as shown D Do Not
3. 1 9cm hole in rear side or floor of cabinet B for direct wiring Right side is easiest location Wood cabinet Sand hole until smooth Metal cabinet Cover hole with grommet Part No 302797 available from your dealer or parts supplier 6 Install a U L listed CSA certified strain relief to the junction box If using conduit use a U L listed CSA certified conduit connector Connect the power supply wire to the junction box Run the other end of wire through cabinet hole B The power supply wire must extend 24 inches 61cm from the back wall into cabinet opening Power supply cord method Local codes may permit a U L listed CSA certified 16 gauge power supply cord Part No 4317824 C with a three prong ground type plug D to connect dishwasher to grounded outlet E 5 Cut a 1 1 2 3 8cm hole in rear or right side of cabinet F for power supply cord Right side is easiest location Wood cabinet Sand hole until smooth Metal cabinet Cover hole with grommet Part No 302797 available from your dealer or parts supplier 6 Install a mating three prong ground type outlet in an adjacent cabinet Water line protect from freezing 7 Cut a 1 2 1 3cm minimum hole G in cabinet wall or floor for water line Left side is easiest location Rough water line H to the cabinet opening Install a manual shutoff valve in the water line where it can be easily used Flush wate
4. from bag Check that all parts were supplied 34 86 4cm min 4 10 2cm 2 1 2 6 4cm aue 10 25 40m 127m e 2 5 1em 2 5 1em 24 61cm Unshaded area must be free of pipes wires and drain hose Power supply cord or cable should not be kinked or pinched between dishwasher and cabinet Leveling legs and wheels adjust to fit 34 inch 86 4cm to 35 inch 88 9cm cabinet opening height If leveling legs and wheels are removed from dishwasher 33 13 16 inches 85 9cm is the minimum cabinet opening height Measure this distance from the lowest point of the underside of the countertop Corner locations require a 2 5 1cm minimum clearance between side of dishwasher door and the wall or cabinet Check location where dishwasher will be installed Do Not install dishwasher over carpeting The location must provide e Protection so that the water inlet and drain lines cannot freeze Damage from freezing is not covered by the warranty If dishwasher will be subject to freezing temperatures and left unused for a period of time see Winterizing instructions in your Use and Care Guide Easy access to water electricity and drainage lines e Convenient loading The best location is to the right or left of a sink o A square opening for proper dishwasher operation and appearance e A cabinet front that is perpendicular to the floor 1 4 64cm minimum clearance between motor and flooring to prevent
5. the dishwasher P Has electrical power been interrupted gt Has the motor overloaded It will reset itself within a few minutes If you need service Maintain the quality built into your appliance by calling a KitchenAid authorized service company To obtain the name and number of an authorized service company gt Contact the dealer from whom you purchased the appliance Look in the Yellow Pages of your telephone directory under Appliances Household Major Service and Repair gt or Call the KitchenAid Consumer Assistance Center When you call you will need gt The dishwasher mode number P The dishwasher serial number Both numbers are listed on the model serial rating plate located behind the door on the front frame of the dishwasher opening Part No 9743822 Rev C 1998 KitchenAid Registered Trademark Trademark of KitchenAid U S A KitchenAid Canada licensee in Canada Printed in U S A
6. to direct wire dishwasher you will need Direct Wire Connection Kit Part No 4317979 Remove power supply cord and make all direct wire connections inside terminal box All electrical connections must be made in accordance with all national and local codes and ordinances e Dishwasher must be connected to a grounded metal permanent wiring system or a ground conductor can be used with the circuit conductors to connect to the ground terminal or lead on the dishwasher e Do not ground to a gas pipe e Do not connect dishwasher to electrical supply until dishwasher is permanently grounded Do not have a fuse in the neutral or ground circuit ais 24 61cm 6 86 4cm min teem 15 2cm 3 1 2 8 9cm sapay 4 10 2cm 2 1 2 bs 2 1 2 6 cm 7 10 25 4cm gt 12 7om 25m ae 2 5 1cm 2 5 1cm 24 610m Cabinet opening preparation WARNING Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher Failure to do so can result in death or electrical shock 1 Disconnect the power supply 2 Put on gloves and safety glasses Electrical 3 Pick one method to follow Direct wire or Power supply cord depending upon your dishwasher and local codes 4 Complete wiring to cabinet opening according to wiring method you need Follow all local codes and ordinances Leveling the dishwasher A WARNING Tip Over Hazard
7. KitchenAid HOME APPLIANCES APPAREILS ELECTROMENAGERS www kitchenaid com Installation Instructions Quick Reference Y 4 Para nwo NIS Section introduction Product dimensions Built in opening dimensions Electrical requirements Water requirements Drain requirements installation steps Need assistance Back cover ao The KitchenAid Consumer Assistance Center is open 24 hours a day 7 days a week Call 1 800 422 1230 The call is free within the continental United States In Canada call 1 800 461 5681 for English and 1 800 461 5703 for French Call the KitchenAid Consumer Assistance Center when you jp Have questions about dishwasher installation or operation gt Need to obtain the name and number of a KitchenAid authorized service company Important e Installer Leave Installation Instructions with the homeowner e Homeowner Keep Installation Instructions for future reference e Save Installation Instructions for local electrical inspector s use Important Read and save these Part No 9743822 Rev C Pi ce n 9743822 R v C Installation steps cont from page 8 If connecting dishwasher with power supply cord check that power supply is disconnected AWARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or elec
8. a qualified electrician To assure that the electrical installation is adequate and in conformance with all national and local codes and ordinances Dishwasher must be connected to the proper electrical voltage and frequency as specified on the model serial rating plate The model serial rating plate is located behind the door on the front frame of the dishwasher opening CONNECT WITH COPPER WIRE ONLY e 120 volt 60 Hz AC only 15 ampere fused electrical supply is required e A time delay fuse or circuit breaker is recommended e It is recommended that a separate circuit serving only this appliance be provided e Some models are already equipped with a power supply cord Ifa power supply cord is not supplied Power Supply Cord Kit Part No 4317824 is available from your local dealer or parts supplier Follow the kit instructions for installing power supply cord If the kit is not available locally use a U L listed CSA certified three conductor 16 gauge six foot power supply cord that meets all local codes and ordinances It must be routed so it does not touch the dishwasher motor or lower portion of the dishwasher tub A strain relief must be used to secure the power supply cord to the dishwasher terminal box The power supply cord must be plugged into a mating 3 prong ground type outlet grounded in accordance with all national and local codes and ordinances e Ifa power supply cord is attached to dishwasher but you need
9. been installed except access and lower panels and no steps were skipped Check that you have all the tools you used Read the Use and Care Guide that came with your dishwasher Reconnect power supply to dishwasher Set the dishwasher to run the Normal cycle Start dishwasher and allow it to run for 2 minutes Open dishwasher door The water level should be deep enough to cause the float A to float on the water If the water level is correct close the door and allow the dishwasher to complete the cycle If the dishwasher does not fill to the proper level check the following e Is the shutoff valve in the water supply line completely open e Is the water supply line blocked or kinked Check that there are no water leaks If there are water leaks tighten fittings Need assistance The KitchenAid Consumer Assistance Center is open 24 hours a day 7 days a week Call 1 800 422 1230 The call is free within the continental United States In Canada call 1 800 461 5681 for English and 1 800 461 5703 for French Call the KitchenAid Consumer Assistance Center when you p gt Have questions about dishwasher installation or operation gt Need to obtain the name and number of a KitchenAid authorized service company If dishwasher does not operate check these points P Has the circuit breaker tripped or the house fuse blown Is the door closed tightly and latched gt Has the cycle been set correctly to start
10. cut ribbed section to shorten drain hose E Secure drain hose to air gap with spring type clamp F If spring type clamp does not fit smaller section of drain hose connector use a smaller clamp Smaller clamps are available at plumbing supply stores Connect the air gap to waste tee using a rubber connector G and spring or screw type clamps H The waste tee connection MUST be ahead of the drain trap I and 20 inches 50 8cm minimum above the floor J Drain hose K to air gap L to disposer M Knock out disposer inlet plug N from inlet If inlet plug falls inside disposer you must remove inlet plug before connecting drain hose If disposer is already installed in sink you may need to remove disposer from sink to remove plug DO NOT cut end of drain hose Secure drain hose to air gap with spring type clamp 0 Connect the air gap to disposer using a rubber connector P and spring or screw type clamps Q Most disposers have 7 8 connectors or special connectors are available at plumbing supply stores The disposer connection MUST be ahead of the drain trap R and 20 inches 50 8cm minimum above the floor S All parts are available from your dealer D Water and electrical connection Apply Teffon tape to 90 elbow fitting A and connect fitting directly to water inlet valve B Attach water supply line C to fitting Do Not allow the water pipe or tubing
11. ifferent holes E in base an Reattach access and lower panel to dishwasher so that the bottom edge of the lower panel contacts the floor Your installation ts now complete Keep Installation Instructions and Use and Care Guide close to dishwasher for easy reference Your safety and the safety of others is very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to hazards that can kill or hurt you and others All safety messages will be preceded by the safety alert symbol and the word DANGER or WARNING These words mean DANGER You will be killed or seriously injured if you don t follow instructions A WARNING You can be killed or seriously injured if you don t follow instructions All safety messages will identify the hazard tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed It is your responsibility to e Observe all governing codes and ordinances e comply with the installation specifications and dimensions e properly install dishwasher e make sure you have everything necessary for proper installation e contact a qualified installer to insure that the electrical and plumbing installations meet all national and local codes and ordinances
12. nches 50 8cm minimum above the floor M e Install a U L listed CSA certified strain relief F to the terminal box Run power supply wire through strain relief If using conduit use a U L listed CSA certified conduit connector Run conduit through connector N Connect the white wire G from the power supply wire to the white wire in the terminal box with twist on wire connector e Connect the black wire H from the power supply wire to the black wire in the terminal box with twist on wire connector If the ground connector J looks like this Loosen front nut J on ground connector located on the back of terminal box Do Not loosen the rear nut K on the ground connector e Form the bare ground wire L into a U shaped hook Wrap ground wire hook clockwise around ground connector and between the rear and front nuts Securely tighten the front nut J over the ground wire e Tighten strain relief or conduit connector screws M OR If the ground connector 1 looks like this Loosen screw J on ground connector located on the back of terminal box e Form the bare ground wire K into a U shaped hook Wrap ground wire hook clockwise around ground connector and under the washer L Securely tighten the screw J e Tighten strain relief or conduit connector screws M Replace terminal cover E Installation steps cont on page 9 gt Connect the white wire Q from the power sup
13. ply cord to the white wire in the terminal box with twist on wire connector e Connect the black wire R from the power supply cord to the black wire in the terminal box with twist on wire connector If the ground connector S looks like this e Loosen front nut T on ground connector located on the back of terminal box Do Not loosen the rear nut U on the ground connector Form the bare ground wire V into a U shaped hook Wrap ground wire hook clockwise around ground connector and between the rear and front nuts Securely tighten the front nut F over the ground wire e Tighten strain relief screws W OR If the ground connector S looks like this e Loosen screw T on ground connector located on the back of terminal box Form the bare ground wire U into a U shaped hook Wrap ground wire hook clockwise around ground connector and under the washer V Securely tighten the screw T e Tighten strain relief screws W e Replace terminal cover 0 Plug power supply cord X into mating grounded outlet Open door about 3 inches 7 6cm and check for equal spacing C between inner door and tub sides If spacing is not equal loosen bracket screws and shift tub Tighten bracket screws Remove newspaper or towel from dishwasher Open and close door several times The door should open and close easily If door closes too quickly or falls open adjust door springs D by moving spring ends to d
14. r line into a bucket to get rid of any particles that may clog inlet valve Check that there are no sharp bends or kinks in the water line that may restrict the water flow Turn shutoff valve to the OFF position Drain hose 11 Cut a 1 1 2 3 8cm diameter drain line opening T in the cabinet wall or floor Adjust the front leveling legs E the number of turns listed in the chart The dishwasher should be installed as level as possible from front to back Put the spring type drain hose clamp F over the drain connector G Push drain hose H onto drain connector Use pliers to open clamp and slide clamp over drain hose and drain connector Check that drain hose is securely attached to drain connector Tilt dishwasher backwards on wheels when moving across floor to prevent damage to floor covering Latch 1 the dishwasher door Grasp the sides of the dishwasher door near the console J Tilt dishwasher backwards on wheels Move dishwasher close to cabinet opening Do Not push on the center of the console Discard shipping base or hardboard Insert drain hose into hole cut into cabinet Check that drain hose does not contact door springs motor or water line e Do Not run drain hose over top of tub Check that drain hose is not kinked or twisted Insert power supply cord into hole cut into cabinet If using power supply wire adjust wire and pull towards dishwasher terminal box e Do Not pinch power s
15. the motor from overheating 20 50 8cm The hot water line to the dishwasher must provide between 20 125 psi 138 862 kPa water pressure The hot water heater should be set to deliver 120 F 49 C minimum water temperature to the dishwasher for best results A 3 8 minimum O D copper tubing inlet line is recommended Dishwasher inlet valve has 3 8 N P T internal pipe threads e All solder connections must be made before water line is connected to dishwasher inlet valve Do Not solder within 6 inches 15 2cm of inlet valve The drain hose supplied meets AHAM DW 1 test standards gt The drain hose must have a high drain loop 20 inches 50 8cm above floor This will help to prevent backflow or water siphoning during dishwasher operation o An air gap must be used in the high drain loop if the drain hose is connected to house plumbing lower than 20 inches 50 8cm gt The waste tee or disposer inlet must be 20 inches 50 8cm minimum above the floor Drain hose must be installed to waste tee or inlet above drain trap in house plumbing Drain line and fittings must be 1 2 minimum LD e Ifa longer drain hose is required the maximum length is 12 feet 3 7m Check that drain hose is resistant to heat and detergent Direct wire method Local codes may permit using armored or non metallic sheathed copper wire A with ground wire to connect dishwasher to junction box 5 Cut 2 3 4
16. to contact the motor or dishwasher legs D Turn on water supply and check for leaks Check electrical requirements Be sure you have correct electrical supply and recommended grounding method See Page 4 If connecting dishwasher using direct wire method check that power supply is disconnected A Ae Electrical Shock Hazard Electrically ground dishwasher Connect ground wire to green ground connector in terminal box Do not use an extension cord Failure to do so can result in death fire or electrical shock e Remove the dishwasher terminal box cover E Attachment WARNING Tip Over Hazard Do not use dishwasher until completely installed Do not push down on open door Doing so can result in serious injury or cuts Open dishwasher door and remove all shipping materials Remove bottom rack Place newspaper A or towel over bottom of dishwasher to prevent screws from falling into pump area when securing dishwasher to countertop The dishwasher MUST be secured to countertop or floor to keep it from tipping when door is opened Countertop attachment Secure dishwasher to countertop with two No 10 x 1 2 Phillips head screws B Do Not drop screws into the bottom of the dishwasher Screws if dropped in pump area may cause damage to pump or motor Floor attachment Use floor attachment kit Part No 4378968 available from your dealer Check operation Check that all parts have
17. trical shock e Use power supply cord kit Part No 4317824 available from your dealer or parts supplier Follow instructions with kit for installing power supply cord If the cord kit is not available a U L listed CSA certified 16 gauge three conductor power supply cord and strain relief must be used Six feet 1 8m must be the maximum length of power supply cord Route power supply cord so it does not touch dishwasher motor or lower part of dishwasher tub Remove the dishwasher terminal box cover 0 Install a U L listed CSA certified strain relief P to the terminal box Run power supply cord through strain relief Tools amp materials needed for installation A electric drill N level B Phillips screwdriver O safety glasses C flat blade screwdriver P gloves D 2 adjustable wrenches R Teflon tape E pliers S Drain tube adapter F measuring tape or ruler Part No 9741366 G pipe wrench available from your H hole cutters 1 2 3 4 dealer if Connec ting to a 1 1 2 1 2 LD drain line I tubing cutter Not shown J wire stripper 90 elbow with 3 8 N P T K utility knife external threads on one L 11 32 and 1 4 nut driver end The size of the other j or hex socket end must fit your water supply line M 2 twist on wire connectors for 16 gauge wire Parts supplied for installation A 2 drain hose clamps B 2 No 10 x 1 2 Phillips head screws Remove parts
18. upply cord or kink power supply wire between dishwasher and cabinet Move dishwasher completely into cabinet opening Center dishwasher in opening Check that leveling legs K are firmly against the floor Align the dishwasher door with front of cabinet doors Check that spacing L is the same on both sides Alternate Connection Methods No Air Gap If local codes permit the dishwasher drain hose may be connected directly to a waste tee or waste disposer Drain hose A to waste tee B Cut drain end of drain hose as shown C Do Not cut ribbed section to shorten drain hose D Secure drain hose to waste tee with spring or screw type clamp E If spring type clamp does not fit smaller section of drain hose connector use a smaller clamp Smaller clamps are available at plumbing supply stores The waste tee connection MUST be ahead of the drain trap F and 20 inches 50 8cm minimum above the floor G Drain hose H to disposer I Knock out disposer inlet plug from inlet J If inlet plug falls inside disposer you must remove inlet plug before connecting drain hose If disposer is already installed in sink you may need to remove disposer from sink to remove plug DO NOT cut end of drain hose Secure drain hose to disposer with spring or screw type clamp K Most disposers have 7 8 connectors or special connectors are available at plumbing supply stores The disposer connection MUST be ahead of the drain trap L and 20 i
Download Pdf Manuals
Related Search