KitchenAid 3187359 Oven User Manual
Contents
1. 120 240 Volts Kiowans Fuse Size amps zee E ea swo wo i OVEN MUST BE CONNECTED WITH COPPER WIRE ONLY Wire sizes and connections must E conform to the requirements of the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances Wires sizes and connections must conform with the rating of the appliance Copies of the standards listed may be obtained from National Fire Protection Association Batterymarch Park Quincy Massachusetts 02269 This appliance should be connected directly to the fused disconnect or circuit breaker box through flexible armored or non metallic sheathed copper cable with grounding wire The flexible armored cable from the appliance should be connected directly to the junction box E Locate the junction box to allow as much slack in the cable as possible between the junction box and the appliance so that the oven can be moved if servicing is ever necessary Do Not cut the conduit F A U L listed conduit connector must be provided at the junction box G A wiring diagram is included in the Tech Sheet The Tech Sheet is located behind the air grille Electrical connection WARNING Electrical Shock Hazard e Electrical ground is required on this _ appliance e Do Not connect to the electrical supply until appliance is permanently grounded Disconnect power to the junction box before making the electrical c2. or LOWER pad Then press the BROIL pad and 600 will appear in the display Press the START ENTER pad to start the broil operation The ON Inner and Outer Broil Elements and Oven Cavity symbols will light in the display In 1 2 minutes the upper elements should glow red Press the UPPER OVEN or LOWER OVEN CANCEL OFF pad To get the most efficient use from your new oven read your KitchenAid Use amp Care Guide Keep Installation Instructions and Guide close to oven for easy reference Numbers correspond to steps If the range does not operate e Check that the circuit breaker is not tripped or the house fuse blown e See Use and Care Guide for troubleshooting checklist NOTE Refer to Use and Care Guide for operating instructions and cleaning instructions Part No 3187359 Rev A 1994 KitchenAid If you need assistance The KitchenAid Consumer Assistance Center will answer any questions about operating or maintaining your oven not covered in the Installation Instructions The KitchenAid Consumer Assistance Center is open 24 hours a day 7 days a week Just dial 1 800 422 1230 the call is free When you call you will need the oven model number and serial number Both numbers can be found on the serial rating plate located behind the upper oven door on the front frame KitchenAid HOME APPLIANCES Prepared by KitchenAid St Josep
3. grasp the oven doors or to lift ovens properly could result in damage to the product or personal injury Insert a nail or equivalent 5 32 diameter item into the hole in each of the hinges Close the door as far as possible Lift the oven door off of the hinges Set aside CAUTION Property Damage Before moving oven across floor check that oven is on shipping base or slide oven onto cardboard or hardboard Failure to follow these instructions may result in damage to floor covering Turn power supply off Move oven close to final position Remove and discard shipping base Feed appliance cable through the opening in cabinet Make electrical connection See Electrical requirements and Electrical connection sections Panels A and B CAUTION Product Damage Carefully push against the seal area of the oven front frame when pushing the oven into the cabinet Do Not push against outside edges Failure to follow these instructions can result in damage to oven finish Remove and discard shipping base Lift oven up into cabinet cutout using the oven opening as an area to grip Push against seal area of front frame to push oven into cabinet Center oven into cabinet cutout Use eight screws through the mounting holes in the front frame of the oven to secure the oven to the cabinet Do Not overtighten screws Put the air grille in place below the
4. KitchenAid HOME APPLIANCES a FAUT FE j oii Part No 3187359 Rev A Electric Built in 30 Thermal Convection Double Oven IMPORTANT Read and save these instructions IMPORTANT installer Leave Installation Instructions with the homeowner Homeowner Keep Installation Instructions for future reference Save Installation Instructions for local electrical inspector s use Cabinet door Note There must be 1 min between bottom of cabinet door and top of oven console 2 1 2 min 28 1 2 min m gt available the u iien ney cutout should be made 28 5 8 K 23 min cabinet depth _ l J 56 916 opening height l l l Electrical h 56 716 supply junction box recessed oven height L max below s m support surface U gt z 4 7 min recommended so upper oven door when open is 36 from floor Important Observe all governing codes ordinances The oven support surface must be flush with the bottom of the cabinet cutout See Note opening width it 28 58 is Oven control console 28 3 8 recessed oven width 58 38 overall helght See Note overall width Before you start Read the electrical and carpentry instructions Proper installation is your responsibility A qualified technician should install this oven Make sure you have everything necessary for correct
5. h Michigan 49085 If you need service In the event that your KitchenAid appliance should need service call the dealer from whom you purchased the appliance or a KitchenAid authorized service company A KitchenAid authorized service company is listed in the Yellow Pages of your telephone directory under Appliances Household Major Service or Repair You can also obtain the service company s name and telephone number by dialing free within the continental United States the KitchenAid Consumer Assistance Center telephone number 1 800 422 1230 A special operator will tell you the name and number of your nearest KitchenAid authorized service company Printed on recycled paper 10 post consumer waste 50 recovered materials Printed in U S A
6. ilure to do so could cause the oven to move or tip during use and result in personal injury Tools needed for Phillips screwdriver Parts supplied for installation Panel A Electrical requirements WARNING Electrical Shock Hazard Electrical ground is required on this appliance Do Not ground to a gas pipe e Do Not have a fuse in the neutral or grounding circuit A fuse in the neutral or grounding circuit could result in an electrical shock e Do Not use an extension cord with this appliance e Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded Failure to follow these instructions could result in serious injury or death If codes permit and a separate grounding wire is used it is recommended that a qualified electrician determine that the grounding path is adequate IMPORTANT Save Installation Instructions for the local electrical inspector s use This appliance must be connected to the proper electrical voltage and frequency as specified on the serial rating plate located behind the oven door on the front frame A fuse is required in both sides of the line A time delay fuse or circuit breaker is recommended Use the voltage and kilowatt rating given on serial rating plate to select the proper fuse size Fuse Requirements 120 208 Volts Kiiewatts Fuse Size amps fe2wes o s swa oo
7. installation It is the responsibility of the installer to comply with the installation clearances specified on the serial rating plate The serial rating plate can be found behind the upper oven door on the frame of the oven Check location where the built in oven will be installed The location should be away from strong draft areas such as windows doors and strong heating vents The built in oven should be located for convenient use in the kitchen Cabinet opening dimensions that are shown must be used Dimensions given are for a built in oven sitting on a contact surface 2 3 4 below the open oven door height The contact surface must be solid and level and flush with the bottom of the cabinet opening The recessed installation area must provide complete enclosure around the recessed portion of the oven ALL OPENINGS IN THE WALL OR FLOOR WHERE THE BUILT IN OVEN IS TO BE INSTALLED MUST BE SEALED Electrical ground is required See Electrical requirements WARNING Electrical Shock Hazard It is the customer s responsibility e To contact a qualified electrical installer To assure that the electrical installation is adequate and in conformance with National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances Failure to do so could result in fire electrical shock or other personal injury Personal Injury Hazard Securely fasten oven to cabinet using the 8 screws provided Fa
8. ite appliance cable wire to the neutral white wire in the junction box 4 Connect the two black wires together then the two red wires together See Figure 2 5 Connect the green or bare grounding wire from the appliance cable to a grounded wire in the junction box C If connecting to a four wire electrical system Do Not connect the cabinet grounding conductor to the neutral white junction box wire Cable from Junction bok power supply Bare or j Black wires green J N u L listed t ASS conduit Figure 3 connector 1 Disconnect the power supply 2 Separate the green or bare and white appliance cable wires 3 Connect the white appliance cable wire to the neutral white wire in the junction box 4 Connect the two black wires together then the two red wires together See Figure 3 5 Connect the green appliance cable wire to the green grounding wire in the junction box Now start With oven in kitchen 1 Remove shipping materials tape and protective film from oven Do Not remove shipping base at this time 2 Remove the racks and other parts from inside both ovens WARNING Personal Injury Property Damage Hazard e Use both hands to remove oven doors Grasp only the sides of oven doors e Do Not use handle or any portion of the trim for lifting e Because of the weight and size of the oven two or more people are needed to move and safely install the oven Failure to properly
9. onnection e This appliance must be connected to a grounded metallic permanent wiring system or a grounding connector should be connected to the grounding terminal or wire lead on the appliance Failure to do so could result in a fire personal injury or electrical shock This appliance is manufactured with white neutral power supply wire and a cabinet connected green grounding wire twisted together Connect the appliance cable to the junction box through the U L listed conduit connector Complete electrical connection according to local codes and ordinances A Where local codes permit connecting the cabinet grounding conductor to the neutral white junction box wire Cable from Junction power supply box Bare or green wire U L listed d conduit connector Figure 1 A Grounded Neutral 1 Disconnect the power supply 2 Remove the terminal block cover 3 Connect together 3 wires green and white appliance cable wires and the neutral white wire in junction box 4 Connect the two black wires together then the two red wires together See Figure 1 Panel B B Where local codes Do Not permit connecting the cabinet grounding conductor to the neutral white junction box wire Cable from junenen power supply Cable conduit from oven connector Figure 2 Ungrounded Neutral 1 Disconnect power supply 2 Separate the green and white appliance cable wires 3 Connect the wh
10. oven opening making sure that the flange is at the bottom Slide the air grille into position and attach it to the oven cabinet with the three black or chrome metal screws provided Replace the oven racks Replace the oven door by fitting both corners of the door over the ends of the hinges Remove the nails from the hinges Close the oven door If the door does not close you have not pushed the door completely onto the hinges Panel C OVIN Stitcis teI BOE Z Turn on the power supply 88 88 should appear in the clock display Press the CLOCK SET button TIME HR AND MIN will light in the display 0 00 will appear and will be flashing Press the numbers pads for the correct time of day Press the START ENTER pad to start the clock Check the operation of the BAKE element Both ovens Press the oven UPPER or LOWER pad Then press the BAKE pad and 350 will appear in the display Press the START ENTER pad to start the bake operation Lo and the ON Bake Element Outer Broil Element and Oven Cavity symbols will light in the display In 1 2 minutes the bottom element should glow red The upper element should become hot but not glow red and the oven should be heating Press the oven UPPER OVEN or LOWER OVEN CANCEL OFF pad 111 Check the operation of the BROIL elements Both ovens Press the oven UPPER
Download Pdf Manuals
Related Search