Kenwood KTC-HR300 Car Stereo System User Manual
Contents
1. iTunes Tagging HD Radio Tagging Using an iTunes Tagging enabled HD Radio you can ag your music When you hear a song you enjoy on your local HD Radio station The song s information will then be saved on this unit The saved songs will then show up in a playlist called Purchased in iTunes the very next time you sync your iPod to your computer So then you just need to click and then easily buy and download the song you were agging directly from the Apple iTunes Music Store To use the iTunes Tagging HD Radio Tagging function a compatible control unit is required The tag registration method is described in the instruction manual of the control unit English 3 Operations CD Receiver Tuning Selecting the station 1 Select HD Radio source Press the SRC button Select the HD Radio HD RADIO display 2 Select the HD FM band Press the FM button Each time the FM button is pressed it switches between the HF1 HF2 and HF3 bands Select the HD AM band Press the AM button 3 Tune up or down program Press the ka a or gt gt button If the sub channel is available in Digital FM broadcast when lt Tuning Mode gt is set to Auto seek or Manual the channel can be switched Example Analog FM Analog FM Digital FM Analog FM Digital FM 1ch Digital FM 2ch maa Digital FM 8ch Digital FM lt Tuning Mode gt Auto seek or Manual lt Receive Mode gt2. Auto mode HD FM band During the reception of tune up OOSA During the reception of tune down Using lt Receive Mode gt the modes can be switched to digital broadcast automatic switching analog broadcast only or digital broadcast only When Digital has been set with lt Receive Mode gt the seek time will be longer to allow a check of whether the transmission is a digital broadcast It will take a few seconds to receive the digital broadcasting after selecting the frequency When Tune up button is pressed it will switch to the next frequency if it is switched before receiving the Digital broadcasting When Tune down button is pressed it will be received from Analog broadcasting if the Digital broadcasting has never been received 1 When lt Tuning Mode gt is set to Manual the frequency will be switched while pressing ka a or gt I buttons Some of the models have the following displays when the Main channel and Sub channel are switched Main Primary PRI When it is switched to the Main channel 4 KTC HR300 Sub Secondary SEC When it is switched to Sub channel Tuning Mode Sets the tuning mode Press the AUTO button Each time the button is pressed the Tuning mode switches as shown below Tuning mode Display Operation Auto seek Auto1 Automatic search for a station Search in order of the stations in the Pres
3. Linking will be displayed for few seconds until it is received When lt Receive Mode gt page 4 is set to Digital or Analog it cannot be received if the setting is differed from the preset Auto Memory Entry Putting a station with good reception in the memory automatically 1 Select the band for Auto Memory Entry Press the FM or AM button 2 Open Auto Memory Entry Press the AME button for at least 2 seconds Save 6 stations with the best reception in the memory and close Auto Memory Entry Sub channel of Digital FM cannot be registered English 5 Operations CD Receiver Switching Display When you are listening to an HD Radio station you can switch over the display information as follows For operations see the lt Switching Display gt lt Display Mode Switching gt lt Text Display Switching gt page of the instruction manual of your control unit What is displayed may partly depend on control unit to be connected HD Radio mode Information Display Station Name 8 Station Name NAME ST NAME Song title Artist name Album name Title TITLE Genre Detailed station name 128 Receive Frequency Frequency FREQ The number in the indicates the maximum number of displayed characters When a current receiving station dose not send text information the frequency is displayed The Station name or Song title during reception of the Digital FM broadcast
4. buttons Tune up or down program 0 9 buttons Press buttons 1 6 to recall preset stations English 7 Operations DVD monitor Functions While Displaying the Control Screen Switches to the source control screen to use various functions KVT 512 DDX512 DNX5120 DNX512EX ca AME SEEK 4Line S sT AUTOT AUTOT TEL v 8 KTC HR300 i IKENWOOD J me J sne l m a Source Select DARI A HDpADIO usg A nee Aa iPod VIDEO f Iy A y HD FM Switches to the HD FM1 2 3 band HD AM Switches to the HD AM band a bi Tunes in a station Use the SEEK to change the frequency switching CH DOWN CH UP Selects a channel program AME Selects the Auto Memory mode See lt Auto Memory gt page 10 SEEK Switches the Seek mode The mode is switched in the following order each time you touch the button Display Setting AUTO1 Tunes in a station with good reception automatically AUTO2 Tunes in stations in memory one after another MANU Switches to the next frequency manually 4Line 2Line Switches the number of lines displayed in the Information Display P1 P6 When P1 to P6 buttons appear you can recall the stations on memory For memory of broadcasting stations see lt Auto Memor
5. Digital FM tuner section Frequency range 200 kHz space 87 9 MHz 107 9 MHz Frequency response 20 Hz 20 kHz Analog AM tuner section Frequency range 10 kHz space 530 kHz 1700 kHz Usable sensitivity S N 20dB 20 uV Digital AM tuner section Frequency range 10 kHz space 530 kHz 1700 kHz Frequency response 30 Hz 15 kHz General Operating voltage 14 4 V 11 16 V allowable Current consumption 500 MA Operating Environment 0 C 40 C Installation size W x H x D 164 x 34 x 109 mm 6 1 2 x 1 3 8 x 4 5 16 inch Weight 1 1 Ibs 500 9 Specifications subject to change without notice 14 KTC HR300 FCC WARNING This equipment may generate or use radio frequency energy Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual The user could lose the authority to operate this equipment if an unauthorized change or modification is made NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment may cause harmful interference to radio communications if it is not installed and used in accordance with the instructions However there is no guara
6. turned on te The monaural signals are received several seconds after power on or after FM tuning to an HD Radio station H Radio reception is poor Y The car antenna is not extended Pull the antenna out all the way Y The antenna control wire is not connected t Connect the wire correctly referring to the section on lt Connecting Wires to Terminals gt H The tuner cannot be used by the Dual Zone System Y The HD Radio source cannot be selected by the Dual Zone System te An internal source other than Tuner can be selected The messages shown below display your systems condition Linking Although the Sub channel was selected it is under reading or has not been received HD Off CH Off OFF The Sub channel which cannot be used was selected lt Receive Mode gt is set to Analog therefore the channel cannot be used Set lt Receive Mode gt page 4 9 to Auto or Digital In HD Radio mode the display of Station Name or Song title should be set up The channel information cannot be displayed in the Frequency display page 6 9 English 13 Specifications Analog FM tuner section Frequency range 200 kHz space 87 9 MHz 107 9 MHz Usable sensitivity S N 30 dB 1 2 dBf 1 0 uV 75 Q Selectivity 400 kHz 65 dB Quieting Sensitivity S N 50 dB 16 3 dBf 1 8 uV 75 Q Frequency response 40 Hz 15 kHz Stereo separation 1 kHz 40 dB
7. Also avoid places with too much dust or the possibility of water splashing Do not use your own screws Use only the screws provided If you use the wrong screws you could damage the unit After the unit is installed check whether the brake lamps blinkers wipers etc on the car are working properly English 11 Installation Connecting Wires to Terminals le ro Unit Control Unit e k connector ry KAB connector Accessory gt o e not remove the ferritic core attached The unit can only be connected to a control to the cable unit with either 5L or KAB connector Antenna Cable Accessory Cee To FM AM antenna KTC H R00 SELECT SWITCH Set SELECT SWITCH 1 depending on a NO KAB connector type of a control unit to be 7 L KAB Connector units m use l a DDX5034 DDX5034BT DDX512 DDX514 4 When connecting to the control unit with DDX712 DDX812 DNX5120 DNX512EX 5L connector set this switch down and DNX5140 DNX6000EX DNX6140 DNX7120 DNX8120 KVT 512 KVT 514 As of January 2009 5L when KAB connector set the switch up ON Installation Remove the backing from the velcro strips Accessory and attach it to the bottom of the unit Install the switching unit on the carpet A Please do not install the unit near the dashboard the rear tray or other important components Doing so could lead to injury or accident should the unit come off due to a shock and strike
8. KENWOOD HD Radio TUNER UNIT KTC HR300 INSTRUCTION MANUAL Kenwood Corporation H Radio Take the time to read through this instruction manual Familiarity with installation and operation procedures will help you obtain the best performance from your new HD Radio tuner unit For your records Record the serial number found on the back of the unit in the spaces designated on the warranty card and in the space provided below Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product Model KTC HR300 Serial number US Residence Only Register Online Register your Kenwood product at www Kenwoodusa com B64 4403 00 00 KW Contents What is HD Radio Technology 2 Before use 3 Operations CD Receiver 4 Tuning Tuning Mode Receive Mode Preset Memory Preset Tuning Auto Memory Entry Switching Display Text Scroll n HD Radio source Operations DVD monitor 8 Functions While Displaying the Control Screen Receive mode Auto Memory anual Memory Accessories Installation Procedure 11 Installation 12 Troubleshooting Guide 13 Specifications 14 HD Radio Technology Manufactured Under License From iBiquity Digital Corp U S and Foreign Patents HD Radio and the HD Radio logo are proprietary trademarks of iBiquity Digital Corp iTunes is a trademark of Apple Inc 2 KTC HR300 Wha
9. a person or an important component Do not stick the velcro tape over the serial number 12 KTC HR300 Troubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring Before calling service first check the following table for possible problems H The HD Radio mode cannot be selected Y The connection wire is not connected te Use the connection wire to connect the control unit and the HD Radio tuner H Nothing happens when the buttons are pressed y The computer chip in the unit is not functioning normally ts Press the reset button on the Control Controller No sound can be heard or the volume is low VW The input output wires or wiring harness are connected incorrectly t Reconnect the input output wires and or the wiring harness correctly See the section on WY The preset broadcast station is not transmitting in the mode that was set with lt Receive Mode gt ss Please set lt Receive Mode gt to Auto Y It switches between the Digital broadcasting and Analog broadcasting too often te If the receiving condition is bad lt Receive YW In digital AM broadcasting receive mode switches between stereo and monaural too often ts Receiving condition is bad or unstable Stereo is chosen when receiving condition is good and it switches to monaural when the condition PERIN becomes ad a W The source mode was changed or the power switch was
10. ct a band you wish to store in memory Touch the HD FM or HD AM button EJ Select the Auto Memory mode Touch the AME button EJ Start Auto Memory Touch the lt lt or gt gt button Save six stations with the best reception in the memory and close Auto Memory Entry Manual Memory Stores the current receiving station in memory FJ Select a station you wish to store in memory Touch the HD FM or HD AM button Touch the ka a or gt gt button EJ Store in memory Touch the P1 P6 button for at least 2 seconds Continue to touch until the memory number appears 10 KTC HR300 Accessories Installation Procedure Accessories Installation Procedure 1 To prevent short circuits remove the key from the ignition and disconnect the terminal of the battery 2 Install the FM AM antenna and connect the antenna wire to the HD Radio tuner 3 Connect the HD Radio tuner and the control unit using the provided connection wire 4 Make the proper input and output wire connections for each unit 5 Install the unit in your car 6 Reconnect the terminal of the battery 7 Press the reset button on the control unit A Mounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity
11. et memory Preset station seek Auto2 Manual Manual MANU Normal manual tuning control Receive Mode Sets the receive mode 1 Select menu mode using the control unit Select the menu item Select the Receive Mode HDR mode display 2 Open Receive mode Press the setting button of the menu items in the control unit for at least 1 second 3 Set the Receive mode Switching the setting of menu items Each time the button is pressed the Receive mode switches as shown below Receivemode Display Operation Auto mode Auto Automatically tunes to analog broadcast when receiving the digital broadcast is impossible Digital Digital Digital broadcasts only Analog Analog Analog broadcasts only 4 Exit Receive mode Press the MENU button 5 Exit Menu mode Preset Memory Putting the frequency and channel in the memory 1 Select the band Press the FM or AM button 2 Select the frequency and channel to put in the memory Press the ka a or gt gt button 3 Put the frequency and channel in the memory Press the desired 1 6 button for at least 2 seconds The preset number display blinks 1 time On each band 1 station can be put in the memory on each 1 6 button Preset Tuning Calling up the frequency and channel in the memory 1 Select the band Press the FM or AM button 2 Call up the frequency and channel Press the desired 1 6 button
12. ing displays the channel information as follows Digital AM Station name HD Song title Artist name Digital FM Station name HD Song title Artist name Digital FM 1 Station name HD1 Song title Artist name Station name HD2 Digital FM 2 Song title Artist name When the Main channel is received The sub channel is available in Main channel which is received When the Sub channel is received When listening by the Analog sound HD display switches to FM or AM In HD Radio mode the display of Station Name or Song title should be set up The channel information cannot be displayed in the Frequency display Though some models have two or more lines in the display you cannot display the same information in both the Upper Part and the Lower Part In the control unit with M S P S indicator the indicator will be turned ON or OFF as described below M S P S indicator is OFF M S P S indicator is ON M S P S indicator blinks 6 KTC HR300 Text Scroll Scrolls the display title For operations see the CD features of lt Text Scroll gt in the instruction manual of your control unit Function of remote In HD Radio Source FM button Select the HD FM band Each time the FM button is pressed it switches between the HF1 HF2 and HF3 bands AM button Select the HD AM band lt lt gt gt
13. ntee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help
14. t is HD Radio Technology HD Radio technology enables broadcasters to ransmit a digital signal with its analog signal using existing frequency allocations for FM and AM stations Quality of broadcast is improved to the level of music CD in digital FM and that of analog FM in digital AM oreover if receiving condition is good you can listen o programs in stereo with the digital AM broadcast Digital FM of Supplemental Audio Services can send up to 7 channels of the Supplemental Program Audio other than the Main Program Audio Main Program Audio hereafter called Main channel Supplemental Program Audio hereafter called Sub channel Analog AM Analog AM Digital AM Digital AM HD AM band Main Program Audio Analog FM Main channel i Analog FM Digital FM 4 Analog FM Digital FM 1ch Digital FM 2ch Digital FM 8chi HD FM band Supplemental Program Audio Sub channel Digital broadcasting can send other information than audio so you can display data such as title of music Before use AWARNING To prevent injury or fire take the following precautions To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside he unit Cleaning the Unit If the faceplate of this unit is stained wipe it with a dry soft cloth such as a silicon cloth If the faceplate is stained badly wipe the stain off with a cloth moistened
15. with neutral cleaner then wipe it again with a clean soft dry cloth Notes If you experience problems during installation consult your Kenwood dealer The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on the display on the actual equipment and some of the illustrations on the display may be inapplicable Control Units that can be Connected For the models to which this unit can be connected consult your Kenwood dealer Note that the following restrictions may occur depending on a control unit to be used The HD Radio cannot be selected as a dual zone source How to operate the this unit Operations of this unit are described in the instruction manual of your control unit For those not described in it refer to the following lt Operations gt section CD Receiver Refer to lt Operations CD Receiver gt page 4 KVT 512 DDX512 DNX5120 DNX512EX DDX812 DDX712 DNX8120 DNX7120 Refer to lt Operations DVD monitor gt page 8 Following models are Multi key system models Operations different from those of a standard model may be described in the lt Operations CD Receiver gt section KDC MP728 KDC MP828 KDC X789 KDC X889 The display of the capital and small letters may be differed depending on the model
16. y gt page 10 or lt Manual emory gt page 10 RCV The Receive mode switches in the ollowing order See lt Receive mode gt page 9 TTL Displays the tuned in music information Band display Preset number Frequency display gt w N Radio station information display DDX812 DDX712 DNX8120 DNX7120 Selects the Call Letter 8 Title 32 Artist 32 Album 32 Genre 32 or Station Name 32 KVT 512 DDX512 DNX5120 DNX512EX Changes the display Call letter 8 Station Name 94 Song Title 80 Artist Name 80 Album Name 80 to Genre Name 32 The number in the indicates the maximum number of displayed characters Receive mode Sets the radio broadcasts receive mode EJ Display the Receive mode screen Touch the RCV button EJ Select the receive mode Preset 6 Title Text Auto HD Radio Receive HO FMI Preset 6 Title Text Receive Mode Auto gt lt lt gt The Receive mode switches in the following order Display Setting Auto Automatically tunes to analog broadcast when receiving the digital broadcast is impossible Digital Digital broadcasts only Analog Analog broadcasts only EJ Exit Receive mode Touch the E button English 9 Operations DVD monitor Stores stations with good reception in memory automatically E Display the source control screen FJ Sele
Download Pdf Manuals
Related Search