Kenwood KDC-MP6539U CD Player User Manual
Contents
1. Audio Control Audio Setup You can adjust following Audio Control items You can set Sound system such as follows Adjustment Item Display Range Adjustment Item Display Range Rear volume REAR VOLUME 0 35 Front High Pass Filter HPF F Through 80 100 120 Subwoofer level SUB W LEVE 15 15 150 180 Hz System 0 NATURAL Natural User setting Rock Rear High Pass Filter HPF R Through 80 1 00 120 USER ROCK Pops Easy Top 40 Jazz 150 180 Hz POPS EASY The indicator turns on Low Pass Filter LPF 60 80 120 Through Hz TOP40 JAZZ according to the setting Subwoofer Phase SW PHASE Reverse 180 Normal 0 Bass level BASS LEVEL 8 8 Volume offset NOL OFFSET 8 0 AUX 8 8 Middle level MIDDLE LEVEL 8 8 Loudness LOUD OFF ON Treble level TREBLE LEVEI 8 8 Dual Zone System 2 ZONE OFF ON Balance BALANCE Left 15 Right 15 Fader FADER Rear 15 Front 15 Exit Audio Control mode Volume control mode Source tone memory Puts the set up value in the memory per source USER The ranges selected lastly for Bass level Middle level and Treble level are recalled automatically 1 Select the source to adjust For how to select source item refer to lt Power Source Select button gt of lt Basic Operation gt page 4 2 Enter Audio Control mode2. Can be set while Disc changer source Can be set during Tuner source Can be set during FM reception Can be set while accessing AUX source Can be set only during playback of the iPod source USB source used when the iPod is connected Can be set for sources other than the standby source by setting 2 ZONE of lt Audio Setup gt page 15 to ON Sets ILM MSC SYNC and AT COL CHG in the menu to OFF Refer to the reference page Can be set when the specified type is selected for Display Type Can be set during all sources QM gt olg gt A E 5 E Plin GG 8 883 DN Refer to the respective page for information on how to set the items with reference page number Only the items available to the current source are displayed Strong electrical fields such as from power lines may cause unstable sound quality when CRSC is turned ON In such a situation turn it OFF ILM MSC SYNC is displayed when MENU gt AT COL CHG in lt Function Control gt is set to OFF 1 Enter Function Control mode Press the FNC button Function icon is displayed 2 Select your desired setup item Operation type Operation Movement between items Turn the Control knob Selection of item Press the Control knob Return to previous item Press the FNC button or gall icon Repeat selection and determination until your desired setup item is selected
3. is displayed 7 Exit Audio Preset mode Press the FNC button lt Register 1 pair of Audio Preset Memory You cannot register by the source lt When you press the Reset all the sources will be the setting value which is registered lt The following items cannot be registered Volume Balance Fader Loudness Volume offset Dual Zone System Rear Volume Audio Preset Recall Recalling the sound setup registered by lt Audio Preset Memory gt page 16 1 Select the source For how to select source item refer to lt Power Source Select button gt of lt Basic Operation gt page 4 2 Select Audio Preset item during Menu mode Other than Standby mode Select the Audio Preset display For how to select Function Control items refer to lt Function Control gt page 6 3 Enter Audio Preset mode Press the Control knob for at least 1 second 4 Select the Audio Preset Recall Turn the Control knob Select the Recall display 5 Determine whether to recall the Audio Preset Press the Control knob Recall is displayed 6 Recall the Audio Preset Select YES using the Control knob Press the Control knob Recall Completed is displayed 7 Exit Audio Preset mode Press the FNC button The User memory of SYSTEM Q in lt Audio Control gt page 15 is changed to the value which was recalled The source tone memory item of lt Audio Control gt page 15 is changed to the value
4. 5 Exit Menu mode Press the FNC button lt A title cannot be attached to Audio file media When operation stops for 10 seconds the name at that time is registered and Name Set mode closes Memory numbers FM AM 30 stations Internal CD player 10 discs External CD changer player Varies according to the CD changer player Refer to the CD changer player manual lt Change the title of station CD by the same operation used to name it 10 KDC MP6539U KDC MP6039 Auxiliary Input Display Setting Selects the display below when changing to Auxiliary input source 1 Select Auxiliary input display setting item during Menu mode In AUX mode Select the Name Set display For how to select Function Control items refer to lt Function Control gt page 6 2 Enter Auxiliary input display setting mode Press the Control knob for at least 1 second The presently selected Auxiliary input display is displayed 3 Select the Auxiliary input display Turn the Control knob or push it towards up or down AUX DVD PORTABLE GAME VIDEO TV 4 Exit Auxiliary input display setting mode Press the FNC button lt When operation stops for 10 seconds the name at that time is registered and the Auxiliary input display setting mode closes lt The Auxiliary input display can be set only when the built in auxiliary input or the auxiliary input of optional KCA S220A is used On the KCA
5. Example a MENU Y AR menu DISP ay Y 4 TYPE TEXT a 3 Make a setting Turn the Control knob to select a setting value and then press the Control knob Some items require you to keep pressing the Control knob for 1 or 2 seconds so that you can make a setting For these items the time during which you need to keep pressing the Control knob is displayed in the Entry column in seconds For the functions accompanied by the description of the setting procedure and so forth the reference page numbers are displayed DISP aod 4 Exit Function Control mode Press the FNC button for at least 1 second English 7 Display Settings About Display Type Text Display Selection Shown below are examples of display types Changing the text display Display Display Type Chinese display In Tuner source VPEA To Information Display Station name SNPS Frequency Frequency TYPE B Spectrum Analyzer amp Clock Speana Clock o Clock Clock Date Date TYPE Q a
6. KCA BT100 4 Press the Control knob 5 Select YES using the Control 6 Press the Control knob 7 Press the FNC button lt Menu System gt For how to operate Menu refer knob to lt Function Control gt in this instruction manual About display Cell Phone Status is displayed in this unit Moreover some displays are diffe description of KCA BT100 Instruc he status display of rent from the ion Manual Displays of KCA BT100 Instruction Manual Actual displays on this unit Disconnect HF Disconnect Connect HF Connect Phone Delete Device Delete Phone Status BT DVC Status BT Displays the bluetooth connection status This indicator turns on when connected to this unit Menu Glossary e SRC Select a cell phone is Setting up the Source Select mode 1 Displays source icons for your choice 2 Allows you to select sources one after another e Display f this unit is not operated at le ast 5 seconds with body during playback of the iPod source The color of key illumination is only a recommended color by our campany It does not necessarily match the body color of iPod Compatible iPod models iPod 5th generation iPod classic iPod touch iPod nano 1st 2nd 3rd generation Fifth Generation iPod iPod with video AMP Selecting OFF turns off the built in amplifier Turning off the built in amplifier im
7. System FAT16 32 MP3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windows Media Audio AAC decode AAC LC m4a files Audio section Maximum output power 50Wx4 Full Bandwidth Power at less than 1 THD 22Wx4 Speaker Impedance Tone action Bass 100 Hz 8 dB Middle 1 kHz 8 dB Treble 10 kHz 8 dB Preout level Load CD 2500 mV 10 kQ Preout impedance lt 6000 Auxiliary input Frequency response 1 dB 20 Hz 20 kHz Input Maximum Voltage 1200 mV Input Impedance 100 kQ General Operating voltage 11 16V allowable 144V Current consumption 10 A Installation Size W x Hx D 182x53x 155 mm Weight 140 kg Specifications subject to change without notice English 27
8. you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box A Mounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals Make sure to ground the unit to a negative 12V DC power supply lt Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Auw o Now 22 KDC MP6539U KDC MP6039 Accessories Installation Procedure Do not use your own screws Use only the screws provided If you use the wrong screws you could damage the unit lt If the power is not turned ON Protect is displayed the speaker wire may have a short circuit or touched the chassis of the vehicle and the protection function may have been activated Therefore the speaker wire should be checked lt Ifyour car s ignition does not have an ACC position connect the ignition wires to a power source that can be turned on and off with the ignition key If you connect the ignition wire to a power source with a constant voltage supply as with battery wires the battery may die lt If the console has a lid make sure to install the unit so that the faceplate will not hit the lid when closing and opening lt If the fuse blows first make sure the wires aren t touching to cause a
9. 1 MNAL Dims the turn off even if 5 seconds ILM Dimmer illumination dimmer ion brightness ion in conjunction with the vehicle illumination constantly NAL2 Turns off the upper and lower illuminations and dims the left and right illuminations OFF Does not dim the illumination AT COL CHG Automatic illumination color change Selecting iPod changes the key illumination automatically according to the color of the iPod The marking of products using lasers Except for some areas CLASS 1 LASER PRODUCT The label is attached to the chassis case and says that the component uses laser beams that have been classified as Class 1 It means that the unit is utilizing laser beams that are of a weaker class There is no danger of hazardous radiation outside the unit English 21 Accessories 4 Installation Procedure 1 To prevent a short circuit remove the key from the ignition and disconnect the O battery 2 Make the proper input and output wire connections for each unit Connect the speaker wires of the wiring harness Connect the wiring harness wires in the following order ground battery ignition Connect the wiring harness connector to the unit Install the unit in your car Reconnect the O battery Press the reset button AWARNING If you connect the ignition wire red and the battery wire yellow to the car chassis ground
10. 15 Aa Cannot register a security code Cannot set up Display Illumination Control gt lt Demonstration mode Setting gt page 14 is not turned off What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring Before calling service first check the following table for possible problems General H The Touch Sensor Tone does not sound Y The preout jack is being used ts The Touch Sensor Tone cannot be output from the preout jack H The illumination flashes when the knob or button is operated Y This is the key illumination effect ss You set this effect in MENU gt ILM Effect of lt Function Control gt page 6 H The key illumination effect brought about in conjunction with the sound volume is small Y The key illumination effect may be insufficient depending on the sound volume and sound quality Tuner source H Radio reception is poor Y The car antenna is not extended ts Pull the antenna out all the way Disc source H The specified disc does not play but another one plays instead Y The specified CD is quite dirty ts Clean the CD referring to the CD cleaning of the ERI section on lt Handling CDs gt page 3 V The disc is loaded in a different slot from that specified ts Eject the disc magazine and check the number Y The disc is severely scratched ts Try another disc instead Audio file source H The sound skips when an Audio file is b
11. 2 is displayed as CODE ON or CODE OFF The SRC Select mode can be set in MENU gt SRC Select of lt Function Control gt page 6 When an optional accessory is connected the source name for each device appears When connection of the iPod is recognized the source display changes from USB to iPod USB iPod source is recognized as CD source on the connected unit Function of KDC MP6539U KAN Volume control 9 AUD Turn the knob to adjust the volume Y Attenuator Cm ATT Turning the volume down quickly When the volume is reduced the ATT indicator flashes 4 KDC MP6539U KDC MP6039 Control knob USB Terminal Muting volume upon reception of phone call When there is a call CALI is displayed and the audio system is paused When the call ends CALL disappears and the audio system comes back on The audio system comes back on when SRC is pressed during a call To use the TEL Mute feature you need to hook up the MUTE wire to your telephone using a commercial telephone accessory Refer to lt Connecting Wires to Terminals gt page 23 AY Faceplate release Gr Release Releases the faceplate lock so that it can be removed Refer to the following diagram when reattaching the faceplate O AN The faceplate is a precision piece of equipment and can be damaged by shocks or jolts Keep the faceplate in its faceplate case whi
12. KENWOOD CD RECEIVER KDC MP6539U KDC MP6039 INSTRUCTION MANUAL Kenwoo d Corporation q Made for Windows o ees C Ol iPod 4044 00 00 MW Contents Before use 3 Basic Operations of remote control 19 Basic Operation 4 Appendix 20 General functions Tuner functions Disc amp Audio file play functions Accessories Installation Procedure 22 Connecting Wires to Terminals 23 Function Control 6 Installation Removing the Unit 24 Read through this page first for the setting of each SA Ce q AA function Troubleshooting Guide 25 Display Settings 8 Specifications 27 About Display Type Text Display Selection Key Color Selection Station Disc Naming SNPS DNPS Auxiliary Input Display Setting Music disc Audio file Operation 11 usic Select Direct Music Search Direct Disc Search Basic Operation of Disc Changer Optional Tuner Operation 12 Station Preset Memory Preset Tuning Direct Access Tuning Frequency Step Setting Other Functions 13 Security Code anual Clock Adjustment Date Adjustment Demonstration mode setting Audio Adjustments 15 Audio Control Audio Setup Speaker Setting Audio Preset Memory Audio Preset Recall TV control Optional 18 Basic Operation Preset Memory Preset Tuning Direct ining PSP a IER FTAA DR iPod is a trademark of Apple Inc registered in the U S and o
13. Key Color Selection mode Press the FNC button When colors are adjusted in the detail color mode the values set with User selected in the basic color mode are used lt In the basic color mode selecting Variable Scan scans basic colors During scanning you cannot adjust detail colors English 9 Display Settings Station Disc Naming SNPS DNPS Attaching a title to a Station or CD 1 Receive play the station disc you want to attach a title to 2 Select Name set mode item during Menu mode Select the Name Set display For how to select Function Control items refer to lt Function Control gt page 6 3 Enter Name set mode Press the Control knob for at least 1 second 4 Enter the name Operation type Operation Move the cursor to the enter ush the Control Knob towards right character position or left Select the character type ress the Control knob Select the characters urn the Control knob or push it owards up or down Each time you press the knob the character type alternates between the types shown in the table below Character type Alphabet upper case Alphabet lower case Numbers and symbols Special characters Accent characters Enter characters by using a remote control with numbers buttons Example If you are entering DANCE Character D N N q E Button B ba 2 Dil 6 Di 2 Dil B Times pressed 1 1 2 3 2
14. Press the AUD knob 3 Select the Audio item to adjust Press the AUD knob 4 Adjust the Audio item Turn the AUD knob 5 Exit Audio Control mode Press any button Press a button other than the AUD knob or 4 and ATT button lt Volume offset Sets each sources volume as a difference from the basic volume lt Loudness Compensates for low and high tones during low volume Only the low tone is compensated for when the tuner is selected as a source lt Dual Zone System Main source and sub source Auxiliary input output Front channel and Rear channel separately Set up the channel of sub source by Zone2 of lt Function Control gt page 6 Select Main source by SRC button Adjust the volume of Front channel by AUD knob Adjust the volume of Rear channel by lt Audio Control gt page 15 or A1 W button on the remote control page 19 The Audio Control has no effect on sub source 1 Select the source to adjust For how to select source item refer to lt Power Source Select button gt of lt Basic Operation gt page 4 2 Enter Audio Setup mode Press the AUD knob for at least 1 second 3 Select the Audio Setup item to adjust Press the AUD knob 4 Adjust the Audio setup item Turn the AUD knob 5 Exit Audio Setup mode Press the AUD knob for at least 1 second English 15 Audio Adjustments Speaker Setting Fine tuning so that the System Q value is optimal
15. S220A AUX EXT is displayed by default Music disc Audio file Operation Function of Audio file Internal CD source Music Select Selecting the music you want to listen to from the device or media being played now 1 Enter Music Select mode Turn the Control knob The music list is displayed 2 Search for music Select the category item using the Control knob iPod source iPod Mode ON KDC MP6539U only Operation type Operation Movement between items Turn the Control knob Selection of item Press the Control knob Return to previous item Push the Control knob towards up Return to first item Push the Control knob towards up for at least 1 second Other source Audio file Operation type Operation Movement between items Turn the Control knob or push it towards up or down Selection of item Push the Control knob towards right Return to previous item Push the Control knob towards left Return to first item Push the Control knob towards left for at east 1 second Internal CD source Operation type Operation Movement between track Turn the Control knob or push it towards up or down Selection of track Press the Control knob Return to first track Push the Control knob towards left for at east 1 second The lt a or gt symbol shown beside the displayed item indicates that the item is preceded or followed by another item Se
16. ck is not guaranteed when a cable other than the USB compatible cable is used Connecting a cable whose total length is longer than 5 m can result in abnormal playback About KENWOOD Music Editor of PC application attached to KDC MP6539U lt Music Editor is recorded in the CD ROM attached to this unit lt Refer to the user s manual recorded in the installation CD ROM and Help of Music Editor for the operation method of Music Editor lt The unit can play USB device created by Music Editor lt Information about Music Editor upgrade is put on the site www kenwood com For operating KCA BT100 Optional However the following control methods of the function for this unit may be different from the Instruction manual therefore refer to the following supplemental instruction lt Dialing by Using the Quick Dialing Function gt 1 Press the Control knob Select the DIAL display 2 Press the FNC button 3 Select the number to recall by turning the Control knob 4 Press the Control knob lt Registering to the Preset Dial Number List gt 1 Operation is the same Refer to the instruction manual of KCA BT100 2 Press the FNC button 3 Select the number to memory by turning the Control knob 4 Press the Control knob for at east 1 second lt Deleting a Registered Cell Phone gt 1 3 Operation is the same Refer to the instruction manual of
17. d When removing CDs from this unit pull them out horizontally lt If the CD center hole or outside rim has burrs use the CD only after removing the burrs with a ballpoint pen etc CDs that cannot be used CDs that are not round cannot be used lt CDs with coloring on the recording surface or CDs that are dirty cannot be used This unit can only play the CDs with jess ane es This unit may not correctly play discs which do not have the mark lt You cannot play a CD R or CD RW that has not been finalized For the finalization process refer to your CD R CD RW writing software and your CD R CD RW recorder instruction manual English 3 Basic Operation SRC Release Disc slot AUTO 4 FNC KENWOOD Auxiliary input Rear side AUD General functions y Power Source Select button Cm SRC Turns on the power When the power is ON select a source SRC Select mode 1 Press the SRC button and then turn the Control knob or push it toward left or right To determine the selected source press the Control knob SRC Select mode 2 Pressing this button each time switches between sources Tuner TUNER USB or iPod USB or iPod CD Compact Disc Auxiliary input AUX and Standby STANDBY Press at least 1 second to turn off the power lt When the power is ON the lt Security Code gt page 1
18. e lens in the CD player of the unit Called lens fogging this condensation on the lens may not allow CDs to play In such a situation remove the disc and wait for the condensation to evaporate If the unit still does not operate normally after a while consult your Kenwood dealer lt If you experience problems during installation consult your Kenwood dealer When you purchase optional accessories check with your Kenwood dealer to make sure that they work with your model and in your area Characters that conform to ISO 8859 1 can be displayed Characters that conform to GB2312 or ISO 8859 1 can be displayed Refer to MENU gt Chinese of lt Function Control gt page 6 In this document the description indicator will light means a status is displayed Refer to lt About Display Type gt page 8 for the details of the status display The illustrations of the display the function icon and the panel appearing in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on the display on the actual equipment and some of the illustrations on the display may be inapplicable Handling CDs Do not touch the recording surface of the CD lt Do not stick tape etc on the CD or use a CD with tape stuck on it lt Do not use disc type accessories lt Clean from the center of the disc and move outwar
19. e two AA R6 size batteries Slide the cover while pressing downwards to remove it as illustrated Insert the batteries with the and poles aligned properly following the illustration inside the case English 19 Appendix About Audio file lt Playable Audio file AAC LC m4a MP3 mp3 WMA wma Playable disc media CD R RW ROM Playable disc file format SO 9660 Level 1 2 Joliet Romeo Long file name lt USB device Playable Model DC MP6539U Playable USB device USB mass storage class Playable USB device file system FAT16 FAT32 lt iPod Playable Model DC MP6539U Although the audio files are complied with the standards listed above the play maybe impossible depending on the types or conditions of media or device Playing order of the Audio file In the example of folder file tree shown below the files are played in the order from D to 0 ep ED O Folder L_ do gt Audio file o _ Loo 4 do do An online manual about audio files is put on the site www kenwood com audiofile On this online manual detailed information and notes which are not written in this manual are provided Make sure to read through the online manual as well lt In this manual the word USB device is used for flas memories and digital audio players which have USB terminals lt The word iPod appearing in this manual indicates the iPod connected w
20. eing played Y The media is scratched or dirty ts Clean the media referring to the CD cleaning of Y The recording condition is bad ts Record the media again or use another media H Noise is heard when carrying out Folder Search Y Noise may be produced if folders without audio files exist continuously in the playing media t Do not make folders without audio files English 25 Troubleshooting Guide The messages shown below display your systems condition TOC Error No disc has been loaded in the disc magazine The CD is quite dirty The CD is upside down The CD is scratched a lot Error 05 The disc is unreadable Error 77 The unit is malfunctioning for some reason Press the reset button on the unit If the Error 77 code does not disappear consult your nearest service center Mecha Error Something is wrong with the disc magazine Or the unit is malfunctioning for some reason m gt Check the disc magazine And then press the reset button on the unit If the Mecha Error code does not disappear consult your nearest service center IN Blink The CD player section is not operating properly Reinsert the CD If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted please switch off the power and consult your nearest service center Protect The speaker wire has a short circuit or touches the chassis of the vehicle and then the protec
21. evice and then reconnect it gt Confirm that the software for the iPod is the latest version USB REMOVE The Remove mode has been selected for the USB device iPod You can remove the USB device iPod safely Specifications FM tuner section USB Interface KDC MP6539U Frequency range 200 kHz space 87 9 MHz 107 9 MHz 50 kHz space 87 5 MHz 108 0 MHz Usable sensitivity S N 30dB 9 30 Bf 0 8 uV 75 Q Quieting Sensitivity S N 50dB 15 20 Bf 1 6 uV 75 O Frequency response 3 dB 30 Hz 15 kHz Signal to Noise ratio MONO 70 dB Selectivity 400 kHz gt 80 dB Stereo separation 1 kHz 40 dB AM tuner section Frequency range 10 kHz space 530 kHz 1700 kHz 9 kHz space 531 kHz 1611 kHz Usable sensitivity S N 20dB 28 dBu 25 uV CD player section Laser diode GaAlAs Digital filter D A 8 Times Over Sampling D A Converter 24 Bit Spindle speed 500 200 rom CLV Wow Flutter Below Measurable Limit Frequency response 1 dB 10 Hz 20 kHz Total harmonic distortion 1 kHz KDC MP6539U 0 008 KDC MP6039 0 010 Signal to Noise ratio 1 kHz KDC MP6539U 110 dB KDC MP6039 105 dB Dynamic range 93 dB MP3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windows Media Audio AAC decode AAC LC m4a files USB Standard USB1 1 2 0 Maximum Supply current 500 MA File
22. he figure AccessoryQ Removal tool 2 When the upper level is removed remove the lower two locations lt The frame can be removed from the bottom side in the same manner Removing the Unit 1 Refer to the section lt Removing the hard rubber rame gt and then remove the hard rubber frame 2 Remove the screw M4 x 8 on the back panel 3 Insert the two removal tools deeply into the slots on each side as shown 4 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards he inside Screw M4 x 8 mm commercially available Accessory 2 lt Be careful to avoid injury from the catch pins on the removal tool 5 Pull the unit all the way out with your hands being careful not to drop it Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit Aa Cannot set up the subwoofer Cannot set up the High Pass Filter Cannot set up the Fader lt No Audio control effect on AUX gt lt Subwoofer output gt of lt Basic Operation gt page 4 is not set to On The Dual zone function is enabled 1 lt Audio Setup gt page 15 Aa Cannot set up the subwoofer phase b The Low Pass Filter is set to Through rs lt Audio Setup gt page 15 Aa Cannot select the output destination of the subsource in the Dual zone Cannot adjust the volume of the rear speakers b The Dual zone function is disabled lt Audio Setup gt page
23. he motor antenna or to the power terminal for the booster amplifier of the film type antenna Connect to the terminal that is grounded when either the telephone rings or during conversation To connect the Kenwood navigation system consult your navigation manual To car light control switch Car fuse box Main fuse Battery English 23 Installation Removing the Unit non Japanese cars Metal mounting strap commercially available Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place Self tapping screw commercially available Screw M4 x 8 mm commercially available Make sure that the unit is installed securely in place If the unit is unstable it may malfunction for example the sound may skip Japanese cars 1 Refer to the section lt Removing the hard rubber rame gt and then remove the hard rubber frame 2 Align the holes in the unit two locations on each side with the vehicle mounting bracket and secure he unit with the accessory screws T Toyota cars N Nissan cars 8mm E 8mm 5 MAX MAX LO 25mm o5mm AccessoryG for Nissan car Accessory 4 for Toyota car 24 KDC MP6539U KDC MP6039 Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level Upper the frame and pull it forward as shown in t
24. ing pushing toward left or right No sound is output while playing audio file Folder search Control knob Changes the folder containing the audio file when pushing toward up or down English 5 Function Control Functions in the table below can be setup by using Function Control Category Item Setting Entry Setting overview Condition Page MENU Security Set Sets security code E 3 SRC Select 1 2 Sets the source selection method E 2 iPod Mode OFF ON When set to ON allows you to select music in the manner GU 1 similar to that of the iPod AT COL CHG OFF iPod When the iPod source is used sets whether the illumination iPod EN color is changed by the iPod Beep 0FF 0N Setting the operation check sound beep sound ON OFF 5 Clock Adjust Sets the clock E 1 Date Adjust Sets the date E 1 Date Mode 7types Sets the date display mode E Display OFF ON Turns off the display when no operation is performed 2 Dimmer OFF ONE Dims the display part in conjunction with the lightswitchof EEY the vehicle ILM Dimmer AUTO MNAL1 Sets whether the key illumination is dimmed in conjunction SB 2 MNAL2 2 0FF with the
25. ith the iPod connection cable optional accessory The iPod connected with the iPod connection cable can be controlled from this unit iPods that can be connected with the iPod connection cable are the iPod nano Fifth Generation iPod iPod classic and iPod touch Other iPods cannot be connected KDC MP6539U only 20 KDC MP6539U KDC MP6039 About USB device lt If you start playback after connecting the iPod the music that has been played by the iPod is played first In this case RESUMING is displayed without displaying a folder name etc Changing the browse item will display a correct title etc lt When the iPod is connected to this unit KENWOOD or y is displayed on the iPod to indicate that you cannot operate the iPod When the USB device is connected to this unit it can be charged up provided that this unit is powered Install the USB device in the place where it will not prevent you from driving your vehicle properly You cannot connect a USB device via a USB hub and Multi Card Reader lt Take backups of the audio files used with this unit The files can be erased depending on the operating conditions of the USB device We shall have no compensation for any damage arising out of erasure of the stored data lt No USB device comes with this unit You need to purchase a commercially available USB device When connecting the USB device usage of the CA U1EX option is recommended ormal playba
26. le detached Do not place the faceplate and the faceplate case in areas exposed to direct sunlight excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing To prevent deterioration do not touch the terminals of the unit or faceplate with your fingers Auxiliary input oa Connect a portable audio device with mini plug cable 3 5 9 Use the mini plug cable which is stereo type and does not have any resistance lt The auxiliary input requires the setting made in MENU gt Built in AUX of lt Function Control gt page 6 Subwoofer output a Control knob Switches between ON SUBWOOFER ON and OFF SUBWOOFER OFF each time pushing toward down for at least 2 seconds Function Control Gr FNC Pressing this button allows you to set various functions using the Control knob Refer to lt Function Control gt page 6 MENU Allows you to set up the environment DISP Allows you to set up the display Text Title scroll O Control knob Scrolls the CD and audio file text display when pushing toward up for at least 2 seconds Tuner functions Band select 4 Control knob Switches between FM1 FM2 and FM3 each time pushing toward up Switches to AM when pushing toward down Tuning 69 Control knob Changes the frequency when pushing toward left or right lt During reception of stereo stations the ST indicator is ON AY Tuning mode se
27. lect Gr AUTO Switches as follows each time this button is pressed Tuning mode Display Operation Auto seek Autol Automatic search for a station Preset station seek Auto Search in order of the stations in the Preset memory page 12 Manual Manual Normal manual tuning control ay Auto memory entry Cin AUTO Memorizes six stations with good reception automatically when pressed for at least 2 seconds AO Indicates the button etc to operate Disc play Disc slot Starts playing when a disc is inserted When a CD is inserted the IN indicator is ON 3 inch 8 cm CD cannot be used Attempt to insert using an adapter can cause malfunction y Disc ejection Cin 4 You can eject the disc for 10 minutes after switching off the engine USB device iPod play Function of KDC MP6539U USB Terminal Connecting a USB device starts playback lt For the playable audio file media and devices refer to lt About Audio file gt page 20 Pause and play Gh Control knob Switches between pause and play each time the center is pressed USB device removing Function of KDC MP6539U 4 Press this button for 2 seconds or longer to select the remove mode and the remove the USB device During the remove mode the USB REMOVE indicator is ON Music search 69 Control knob Changes the music when pushing toward left or right Fast reverses or forwards the music while keep
28. lecting a music will play it from the beginning Cancelling Music Select Press the FNC button Music Select cannot be performed during Random play Set the iPod mode in MENU gt iPod Mode of lt Function Control gt page 6 Function of remote control Direct Music Search Searchs the music by entering the track number 1 Enter the music number Press the number buttons on the remote control 2 Search the music Press the ka a or gt gt button Cancelling Direct Music Search Press the gt I button Direct Music Search cannot be performed during playing of iPod Music Editor media Random play or scan play Function of disc changers with remote control Direct Disc Search Searchs the disc by entering the disc number 1 Enter the disc number Press the number buttons on the remote control 2 Search the disc Press the FM or AM button Cancelling Direct Disc Search Press the gt I button lt Direct Disc Search cannot be performed during playing of Random play or scan play Basic Operation of Disc Changer Optional Selecting CD changer source Press the SRC button Select the CD Changer display For how to select source item refer to lt Power Source Select button gt of lt Basic Operation gt page 4 Music search Push the Control knob towards right or left Disc Search Push the Control knob towards up or down English 11 Tuner Operation Stati
29. light switch of the vehicle or it is dimmed constantly ILM Effect OFF ON Sets whether the key illumination color brightness SB is changed in conjunction with the key operation To connect the Bluetooth unit ILM MSC OFF ON Sets whether the key illumination color brightness is SYNC changed in conjunction with the sound volume AMP OFF ON Turns on off the built in amplifier E 2 Zone Rear Front Specifies the destination of AUX input sound when the Dual BB 2 Zone function is turned on Supreme 0FF 0N Turns ON OFF the Supreme function ih CRSC 0FF 0N Switches to Monaural to decrease noise when reception is poor Name Set Sets the station name SNPS disc name DNPS AUX name CEB 10 Chinese 0FF 0N Selects Chinese as the display language E 2 Scroll Auto Manual Specifies whether the text is scrolled automatically Built in AUX OFF 0N Sets whether to display AUX during source selection E CD Read AP Sets the CD read mode E 2 Audio Preset Presets the setting value of the audio control The preset 16 17 value is retained after resetting DEMO Mode OFF 0N Specifies whether to enable demonstration 14 DISP gt TYPE A B C D E F G Sets the display pattern 8 gt GRAPH Spectrum Analyzer 1 2 Sets the Type E spectrum analyzer display e gt SIDE Text ic
30. ning 1 Enter Direct TV Tuning mode Press the DIRECT button on the remote control is displayed 2 Enter the TV channel Press the number buttons on the remote control Example Desired channel Press button 8ch 0 8 Cancelling Direct TV Tuning Press the DIRECT button on the remote control Basic Operations of remote control g O DIRECT 2 Z0NE page 12 18 0 9 V A General control Volume control Gh VOL Source select qh SRC Volume reduce qh ATT In Audio control Audio item select qh AUD Adjusts the Audio item qh VOL Refer to lt Audio Control gt page 15 for the operation method such as the procedures for Audio control and others operations Dual Zone control Dual zone system on and off Gh 2 ZONE Rear channel volume control qh a v In Tuner source y Band select eia Station select T lt Recall preset stations Gh 1 6 In CD USB source Music select qh lt Folder Disc select T FM AM Pause Play qh gt In TV source Band Video input select Mm FM Channel select qh H lt 34 Recall preset channels Gh 1 6 About 4 This button is used when Bluetooth HANDS FREE BOX is connected For more information refer to the instruction manual of Bluetooth HANDS FREE BOX Do not set the remote control in hot places such as on the dashboard Loading and Replacing battery Us
31. numbers towards up or down 4 Confirm the Security Code Press the Control knob for at least 3 seconds When Re Enter is displayed SECURITY SET is also displayed 5 Do the step 3 through 4 operation and reenter the Security Code Approved is displayed The Security Code function activates lt Ifyou enter a Code different from your Security Code you have to start over from step 3 6 Exit Security Code mode Press the FNC button Entering Security Code The Security Code is required to use the audio unit when the unit is first used after removed from the battery power source or the Reset button is pressed 1 Turn the power ON 2 Do the step 3 through 4 operation and reenter the security code Approved is displayed Now you can use the unit lt Ifan incorrect code is entered Waiting is displayed and the input prohibition periods shown in the table below is generated After the input prohibition time lapses SECURITY is displayed and you can reenter the code Number of times the Input prohibited time incorrect code was input 1 2 5 minutes 3 1 hour 4 24 hours English 13 Other Functions Manual Clock Adjustment 1 Select Clock Adjustment item during Menu mode In Standby mode Select the Clock Adjust display For how to select Function Control items refer to lt Function Control gt page 6 2 Enter Clock adjustment mode Press the Cont
32. o Blan Blank O In CD amp External disc source TYPE DJ Information Display Disc title Disc Title 2 Track title Track Title TYPE EJ Play time 8 Track number P Time Ki 2 Disc name DNPS Spectrum Analyzer amp Clock Speana Clock TYPE IF o o Clock Clock Date Date Blank Blank TYPE G f In Audio file source Information Display usic title amp Artist name Title Artist lt To select the Chinese display type select ON in MENU Album name amp Artist name Album Artist gt Chinese of lt Function Control gt page 6 Folder name Folder Name File name File Name Text display part Play time amp Music number P Time Status display Spectrum Analyzer amp Clock Speana Clock Icon display part Clock Clock Spectrum Analyzer display Date Date Clock display Blank Blank 6 Display varied depending on the source In Standby Information Display Standby Source Name Clock Clock Date Date Blan Blank In Auxiliary input source Information Display Auxiliary input name Source Name Spectrum Analyzer amp Clock Speana Clock Clock Clock Date Date Blan Blank 8 KDC MP6539U KDC MP6039 1 Enter Text Display Selection mode In Display Function of KDC MP6539U Type A B C D F Key Color Selecti
33. on Select DISP gt TEXT Selecting the Key Button color For how to select Function Control item refer to 9 y lt Function Control gt page 6 1 Enter Key Color Selection mode 2 Select the text display part Display Type A B Select K COL C D only For how to select Function Control item refer to Push the Control knob towards up or down lt Function Control gt page 6 The selected text display part blinks 2 Select the Key Color 3 Select the text Basic color Turn the Control knob or push it towards left Turn the Control knob or push it towards left or right or right 4 Exit Text Display Selection mode Variable Scan Color1 Color10 User Press the Control knob Detail color RGB based adjustment Operation type Operation If the selected display item does not have any To select the detail color Press the Control knob for at least information alternative information is displayed adjustment mode 1 second Some items cannot be selected depending on the To select the color to adjust Push the Control knob towards right display type and row red green or blue or left When selecting Folder Name while playing with To adjust color Range 0 9 Turn the Control knob or push it iPod names will be displayed depending on currently towards up or down selected browsing items To exit the detail color Press the Control knob adjustment mode 3 Exit
34. on Source Sets the Type A side icon display Q Icon gt TEXT Sets the text display 0000 3 COL Sets the button illumination color 9 PMEM Presets a station gt 72 18 SCA ON When set to ON plays the intro of the music in the folder successively RDM 0N When set to ON plays the music in the folder randomly FIREP 0N When set to ON plays the music repeatedly ED FoREI ON When set to ON plays the music in the folder repeatedly AF2 SCA 0N When set to ON plays the intro of the music on the disc successively RDM 0N When set to ON plays the music on the disc randomly 6 KDC MP6539U KDC MP6039 Category item Setting Entry Setting overview Condition Page M RDM ON When set to ON plays the music in the disc changer randomly TREP ON When set to ON plays the music repeatedly D REP ON When set to ON plays the music on the disc repeatedly Factory setting Function of KDC MP6539U 2 Function of KDC MP6039 Displayed item is depending on currently selected source or mode The mark in Condition column shows the condition to which the item is displayed Can be set in other than standby state Can be set in standby state Can be set while Audio file source of CD USB iPod Can be set while Audio file source of CD USB excluding iPod Can be set while CD Disc changer source
35. on Preset Memory Putting a station in the memory 1 Select the frequency to put in the memory Push the Control knob towards right or left 2 Enter Preset Memory mode Select P MEM For how to select Function Control item refer to lt Function Control gt page 6 3 Select the number to put in the memory Turn the Control knob 4 Determine the number to put in the memory Press the Control knob 5 Allow the determined number to take effect Press the Control knob Cancelling the Preset Memory mode Press the FNC button Preset Tuning Recalling the stations in the memory 1 Enter Preset Tuning Select mode Turn the Control knob A station list is displayed 2 Select a desired station in the memory Turn the Control knob 3 Recall the station Press the Control knob Cancelling Preset Tuning Press the FNC button 12 KDC MP6539U KDC MP6039 Function of remote control Direct Access Tuning Entering the frequency and tuning 1 Enter Direct Access Tuning mode Press the DIRECT button on the remote control is displayed 2 Enter the frequency Press the number buttons on the remote control Example Desired frequency Press button 92 1 MHz FM 0 19 2 1 810 kHz AM 0 8 1 0 Cancelling Direct Access Tuning Press the DIRECT button on the remote control lt You can enter the FM band frequency in steps of a minimum of 0 1 MHz Frequency Step Se
36. proves the quality of the sound from Preout Zone2 Dual Zone Set the destination front speaker Front or rear speaker Rear of the sub source AUX IN when the Dual Zone function is turned on Supreme Technology to extrapolate and supplement with proprietary algorithm the high frequency range hat is cut off when encoding at low bit rate less han 128Kbps Sampling frequency is 44 1kHz Supplementing is optimized by compression ormat AAC MP3 or WMA and processed according to bit rate The effect is negligible with music that is encoded at high bit rate variable bit rate or has minimal high requency range Chinese Chinese language setting When this is set to ON the following character strings are displayed in Chinese Folder name File name Song title Artist name Album name KCA BT100 optional accessory CD Read Sets the method for reading CD When unable to play special format CD set this function to 2 to force playing Note that some music CD may be unplayable even when set to 2 In addition audio files cannot be played when set to 2 Normally keep this set to 1 1 Automatically distinguishes between audio file disc and music CD when playing disc 2 Forces playing as music CD OFF selected the display turns off During a setup mode the display will no apse Reduces the key Illumina AUTO Dims the illuminat the Light switch o NAL
37. rol knob for at least 1 second The clock display blinks 3 Adjusting Clock Operation type Operation Selecting the item hours or Push the Control knob towards right minutes or left Adjust each item Turn the Control knob or push it towards up or down 4 Exit Clock adjustment mode Press the FNC button Date Adjustment 1 Select Date Adjustment item during Menu mode In Standby mode Select the Date Adjust display For how to select Function Control items refer to lt Function Control gt page 6 2 Enter Date adjustment mode Press the Control knob for at least 1 second The date display blinks 3 Adjusting Date Operation type Operation Selecting the item month day Push the Control knob towards right or year or left Adjust each item Turn the Control knob or push it towards up or down 4 Exit Date adjustment mode Press the FNC button 14 KDC MP6539U KDC MP6039 Demonstration mode setting Turning the demonstration mode ON OFF 1 Select Demonstration item during Menu mode Select the DEMO Mode display For how to select Function Control items refer to lt Function Control gt page 6 2 Set the Demonstration mode Press the Control knob for at least 2 seconds Pressing this button for 2 seconds or longer toggles the setting between ON and OFF 3 Exit Demonstration mode Press the FNC button Audio Adjustments
38. short circuit then replace the old fuse with one with the same rating Insulate unconnected wires with vinyl tape or other similar material To prevent a short circuit do not remove the caps on the ends of the unconnected wires or the terminals Connect the speaker wires correctly to the terminals to which they correspond The unit may be damaged or fail to work if you share the wires or ground them to any metal part in the car When only two speakers are being connected to the system connect the connectors either to both the front output terminals or to both the rear output terminals do not mix front and rear For example if you connect the connector of the left speaker to a front output terminal do not connect the connector to a rear output terminal After the unit is installed check whether the brake lamps blinkers wipers etc on the car are working properly Mount the unit so that the mounting angle is 30 or less About CD players disc changers connected to this unit If the CD player disc changer has the O N switch set it to the N position The functions you can use and the information that can be displayed may differ depending on the models being connected Connecting Wires to Termi To USB device fo USB connector 1m KDC MP6539U Steering remote c Do not remove the cap when you do not use the USB cable The connector will cause the uni
39. t to malfunction if it gets in touch with any metallic part of the vehicle need to an exclusi adapter not supp Light Blue Yellow ED To use the steering wheel remote control feature you your car is required nals ontrol OO Rear output R OO Front output L gt 00 Sub Woofer output ve remote lied matches FM AM antenna input AUX input Stereo O Use the mini plug which is stereo type and does not have any resistance To Kenwood disc changer External optional accessory Fuse 10A er 1 Wiring harness El Accessory White White Black Gray Gray Black Green Green Black Purple Purple Black To connect these leads refer to the relevant instruction manuals 8 To front left speaker E To front right speaker ES To rear left speaker 2 To rear right speaker If no connections are made do not let the wire come out from the tab Power control Motor antenna control wire Blue White ANT Motor antenna control wire Blue TEL mute wire Brown MUTE Dimmer control wire Orange White ILLUMI Car fuse box Ignition wire Red Battery wire Yellow Ground wire Black O To car chassis V Connect either to the power control terminal when using the optional power amplifier or to the antenna control terminal in the vehicle Depending on what antenna you are using connect either to the control terminal of t
40. ther countries The AAC logo is trademark of Dolby Laboratories 2 KDC MP6539U KDC MP6039 Before use AWARNING To prevent injury or fire take the following precautions lt To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside the unit Before using this unit for the first time This unit is initially set on the Demonstration mode When using this unit for the first time cancel the lt Demonstration mode Setting gt page 14 How to reset your unit lt If this unit or the connected unit disc auto changer etc fails to operate properly press the Reset button The unit returns to factory settings when the Reset button is pressed Reset button Cleaning the Unit If the faceplate of this unit is stained wipe it with a dry soft cloth such as a silicon cloth If the faceplate is stained badly wipe the stain off with a cloth moistened with neutral cleaner then wipe it again with a clean soft dry cloth A lt Applying spray cleaner directly to the unit may affect its mechanical parts Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty wipe them with a clean soft dry cloth Lens Fogging When you turn on the car heater in cold weather dew or condensation may form on th
41. tion function is activated gt Wire or insulate the speaker cable properly and press the reset button If the Protect code does not disappear consult your nearest service center Unsupported File An Audio file is played with a format that this unit can t support Copy Protect Copy Protection A copy protected file is played Read Error The file system of the connected USB device is broken gt Copy the files and folders for the USB device again If the error message is still displayed initialize the USB device or use other USB devices The USB device is selected as a source although no USB device is connected gt Change the source to any source other than USB Connect an USB device and change the source to USB again No Device N A Device An unsupported USB device is connected No Music Data Error 15 The connected USB device contains no playable audio file Media was played that does not have data recorded that the unit can play 26 KDC MP6539U KDC MP6039 USB ERROR Blink Some trouble may have occurred to the connected USB device gt Remove the USB device then cycle the power switch to ON If the same display is repeated use another USB device iPod Error Connection to the iPod has failed gt Check that the connected iPod is an iPod that is supported See lt About Audio file gt page 20 for information on supported iPods gt Remove the USB d
42. tting Changing the tuning frequency step The original setting is FM band 50 kHz and AM band 9 kHz 1 Turn the power OFF Press the SRC button for at least 1 second 2 Switch the frequency step While pressing the FNC and AUTO buttons press the SRC button Release your fingers from the button after the display appears The frequency step changes to FM band 200 kHz and AM band 10 kHz When the same operation is repeated the frequency step returns to the original setting lt When the frequency step is changed the frequencies in the memory are deleted Other Functions Security Code When Security Code is set possibility of theft is reduced because input of Security Code is prompted to turn on the unit once it is turned off When you activate the Security Code function it cannot be released Note your Security Code is the 4 digit number entered in your Car Audio Passport in this package 1 Select Security Code item during Menu mode In Standby mode Security Set is displayed For how to select Function Control items refer to lt Function Control gt page 6 2 Enter Security Code mode Press the Control knob for at least 1 second When Enter is displayed SECURITY SET is also displayed 3 Enter Security Code Operation type Operation Select the digits to enter Push the Control knob towards right or left Select the Security Code Turn the Control knob or push it
43. when setting the speaker type as follows Speaker type Display OFF OFF For 5 amp 4 in speaker 5 4inch For 6 amp 6x9 in speaker 6x9 6inch For the OEM speaker QEM 1 Enter Standby Select the STANDBY display For how to select source item refer to lt Power Source Select button gt of lt Basic Operation gt page 4 2 Enter Speaker Setting mode Press the AUD knob SP SEL is displayed 3 Select the Speaker type Turn the AUD knob 4 Exit Speaker Setting mode Press the AUD knob 16 KDC MP6539U KDC MP6039 Audio Preset Memory Registering the value setup by Sound Control The memory cannot be erased by the Reset button 1 Setup Sound Control Refer to the following operations to setup the Sound Control lt Audio Control gt page 15 lt Audio Setup gt page 15 2 Select Audio Preset item during Menu mode Other than Standby mode Select the Audio Preset display For how to select Function Control items refer to lt Function Control gt page 6 3 Enter Audio Preset mode Press the Control knob for at least 1 second 4 Select the Audio Preset Memory Turn the Control knob Select the Memory display 5 Determine whether to put the Audio Preset in the memory Press the Control knob Memory is displayed 6 Put the Audio Preset in the memory Select YES using the Control knob Press the Control knob Memory Completed
44. which was recalled by the selected source English 17 TV control Optional Basic Operation Selecting TV source Press the SRC button Select the TV display For how to select source item refer to lt Power Source Select button gt of lt Basic Operation gt page 4 Select the TV band and Video input Push the Control knob toward up Each time you push the knob TV bands and Video input alternate Select the TV channel Push the Control knob towards right or left Preset Memory Putting the TV channels in the memory 1 Select the TV channel to put in the memory Push the Control knob towards right or left 2 Enter Preset Memory mode Select P MEM For how to select Function Control item refer to lt Function Control gt page 6 3 Select the number to put in the memory Turn the Control knob 4 Determine the number to put in the memory Press the Control knob 5 Allow the determined number to take effect Press the Control knob Cancelling the Preset Memory mode Press the FNC button 18 KDC MP6539U KDC MP6039 Preset Tuning Recalling the TV channels in the memory 1 Enter Preset Tuning Select mode Turn the Control knob A list is displayed 2 Select a desired station in the memory Turn the Control knob 3 Recall the station Press the Control knob Cancelling Preset Tuning Press the FNC button Function of remote control Direct TV Tuning Entering the TV channel and tu
Download Pdf Manuals
Related Search