Home

Kenmore 795.7202 Refrigerator User Manual

1. AUTOMATIC ICEMAKER The icemaker will produce 6 cubes per cycle approximately 100 cubes in a 24 hour period depending on freezer compartment temperature room temperature number of door openings and other operating conditions t takes about 12 to 24 hours for a newly installed refrigerator to make ice e Icemaking stops when the ice storage bin is full To turn off the automatic icemaker set the icemaker switch to OFF O To turn on the automatic icemaker set the switch to ON I You can regulate the cube size by pressing the Cube Size Select Button The cube size will vary depending on the Cube Size Setting as well as the water pressure of the connected water line NOTE The water pressure must be between 20 and 125 psi on models without a water filter and between 40 and 125 psi on models with a water filter to produce the normal amount and size cubes AWARNING Personal Injury Hazard DO NOT place fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in 21 Icemaker Automatic Shutoff Arm Cube Size Cube Size Power Switch Indicator Select Button Light AUTOMATIC ICEMAKER continued ACAUTION The first ice and water dispensed may include particles or odor from the water supply line or the water tank Throw away the first few batches of ice about 24 cubes This is also necessary if the r
2. CAUTION Do not hold the handle when removing or replacing the drawer The handle may come off and it could cause personal injury NOTE In the following figures the Pullout Drawer located above the freezer drawer is not shown for clarity Pull the drawer open to full extension Remove the lower basket 1 by lifting the basket from the rail system With both hands hold each rail and push it in to allow both rails to slide in simultaneously Press in the tabs on the rail covers and lift them up to separate from the rail assembly AWARNING If the Durabase divider is removed there is enough open space for children or pets to crawl inside To prevent accidental child and pet entrapment or suffocation risk DO NOT allow them to touch or go ea near the freezer drawer A WARNING DO NOT step or sit down on freezer 0 0 drawer LO j Remove the rail screw on both the left and right rails aie ye tiny fi i v OO 15 HOW TO INSTALL THE FREEZER DRAWER With both hands pull out each rail simultaneously Make sure that you have the correct rail cover for until both rails are fully extended each side i A Right Rail Align the tabs on the covers with the assembly holes look the door support into the rail tabs on on each rail and snap the rail covers in place to both sides secure Ass
3. 38 Solutions Rearrange items with high water content away from air vents If the temperature is too cold adjust the control one increment at a time and wait for the temperature to stabilize Refer to the Setting the Controls section for more information When the refrigerator is operated in temperature below 41 F 5 C food can freeze in the refrigerator compartment The refrigerator should not be operated in temperature below 55 F 13 C When the doors are opened often or for long periods of time warm humid air enters the compartment This raises the temperature and moisture level within the compartment Increased moisture will lead to frost and condensation To lessen the effect reduce the frequency and duration of door openings Refer to the Doors will not close correctly or pop open section in the Troubleshooting section If the temperature is too cold adjust the control one increment at a time and wait for the temperature to stabilize Refer to the Setting the Controls section for more information This is normal for food items with a high water content Do not store food items with high water content in the freezer for a long period of time The icemaker will produce approximately 100 cubes in a 24 hour period Connect the refrigerator to a cold water supply with adequate pressure and turn the water shutoff valve fully open If the problem persists it may be n
4. e Heavy duty aluminum foil e Plastic coated paper Non permeable plastic wraps e Specified freezer grade self sealing plastic bags Follow package or container instructions for proper freezing methods Do not use Bread wrappers Non polyethylene plastic containers Containers without tight lids Wax paper or wax coated freezer wrap Thin semi permeable wrap CAUTION Do not keep beverage cans or plastic food containers in the freezer compartment They may break or burst if they freeze REFRIGERATOR SECTION WATER DISPENSER WATER TRAY To dispense cold water push on the dispenser switch To remove the water tray pull up on the front and pull with a glass it out Note There is no drain beneath the tray You may need to empty the tray of any liquid that collects in it Dispenser Switch Some dripping may occur after dispensing Hold your cup beneath the dispenser for a few seconds after dispensing to catch all of the drops Slightly tilt up the front of the tray and snap the tabs into the holes to reinstall WARNING Do not put your fingers up the ice chute opening Doing so can result in severe injury CAUTION Do not dispense ice into fine china or crystal glasses China or crystal can break 24 REFRIGERATOR SHELVES To reinstall a shelf Tilt the front of the shelf up and Tkheshelves noui reniscraterare adiustable to mest guide the shelf
5. listed below The locations of the features shown below may not match your model LED Interior Lamps Refrigerator Shelves Ice Bin Q Water Filter Durabase Te In door Ice Bin Durabase Divider O Fixed Door Bin Water Tank Cover Crispers Pullout Drawer Modular Door Bins Ice Room Door REFRIGERATOR INSTALLATION A WARNING A WARNING Excessive Weight Hazard Your refrigerator is heavy When moving the refrigerator for cleaning or service be sure to protect the floor Always pull the refrigerator straight out when moving it Do not wiggle or walk the refrigerator when trying to move it as floor damage could occur Excessive Weight Hazard Use two or more people to move and install the refrigerator Failure to do so can result in back or other injury UNPACKING YOUR REFRIGERATOR Remove tape and any temporary labels from your refrigerator before using Do not remove any warning A type labels the model and serial number label or WARN I NG the Tech Sheet that is located under the front of the refrigerator behind the base grille Explosion Hazard Keep flammable materials and vapors such as gasoline away from the refrigerator Failure to do so can result in fire explosion or death To remove any remaining tape or glue rub the area briskly with your thumb Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish so
6. seconds OFF Press and hold the Lock button for three seconds to unlock the control panel and dispenser The dispenser can be set for ice or water Make certain that the control panel is set for the proper operation Press the Water button on the control panel to dispense water Water will not dispense if any of the refrigerator doors are left open After the water filter is replaced dispense 2 5 gallons of water flush for approximately 5 minutes to remove trapped air and contaminates from the system Do not dispense the entire 2 5 gallon amount continuously Depress and release the dispenser pad for cycles of 30 seconds ON and 60 seconds OFF The tubing can kink when the refrigerator is moved during installation or cleaning resulting in reduced water flow Straighten or repair the water supply line and arrange it to prevent future kinks Connect refrigerator to the water supply and turn the water shutoff valve fully open If the problem persists it may be necessary to contact a plumber Problem Possible Causes Ice has bad taste or odor Dispensing warm water Water has bad taste or odor icemaker is making too much ice Water supply contains minerals such as sulfur Icemaker was recently installed Ice has been stored for too long The food has not been stored properly in either compartment The interior of the refrigerator needs to
7. 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber 34 8 FLUSH OUT THE TUBING Turn the main water supply on and flush out the tubing until the water is clear Shut the water off at the water valve after about one quart of water has been flushed through the tubing 9 CONNECT THE TUBING TO THE REFRIGERATOR NOTE Before making the connection to the refrigerator be sure that the refrigerator power cord is not plugged into the wall outlet 1 Remove the plastic flexible cap from the water valve 2 Place the compression nut and ferrule sleeve onto the end of the tubing as shown 3 Insert the end of the copper tubing into the connection as far as possible While holding the tubing tighten the fitting Tubing Clamp 1 4 in Tubing K 1 4 in Compression Nut Ferrule sleeve Refrigerator Connection 35 10 TURN THE WATER ON AT THE SHUTOFF VALVE Tighten any connections that leak ACAUTION Check to see if leaks occur at the water line connections 11 PLUG IN THE REFRIGERATOR Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall Push the refrigerator back to the wall 12 START THE ICEMAKER Set the icemaker power switch to the ON position The icemaker will not begin to operate until it reaches its operating temperature of
8. be cleaned The ice storage bin needs to be cleaned Refrigerator was recently installed The water dispenser has been used recently and the storage tank was exhausted Dispenser has not been used for several hours Refrigerator is connected to the hot water supply Water supply contains minerals such as sulfur Water filter has been exhausted Refrigerator was recently installed Icemaker shutoff arm sensor is obstructed 41 FROUBLESHOOTIN IDE ICE amp WATER L Solutions A water filter may need to be installed to eliminate taste and odor problems NOTE In some cases a filter may not help lt may not be possible to remove all minerals odor taste in all water supplies Discard the first few batches of ice to avoid discolored or bad tasting ice Ice that has been stored for too long will shrink become cloudy and may develop a stale taste Throw away old ice and make a new supply Rewrap the food Odors may migrate to the ice if food is not wrapped properly See the Care and Cleaning section for more information Empty and wash the bin discard old cubes Make sure that the bin is completely dry before reinstalling it Allow 24 hours after installation for the water storage tank to cool completely Depending on your specific model the water storage capacity will range from approximately 20 to 30 oz If the dispenser has not been used for
9. clogged Use a vacuum cleaner with an attachment to clean the condenser cover and vents Do not remove the panel covering the condenser coil area 36 Problem Possible Causes Refrigerator or reezer section is too warm Interior moisture buildup Refrigerator was recently installed Air vents are blocked Doors are opened often or for long periods of time Unit is installed in a hot location A large amount of food or hot food was added to either compartment Doors not closed correctly Temperature control is not set correctly Defrost cycle has recently completed Doors are opened often or for long periods of time Doors not closed correctly Weather is humid Defrost cycle recently completed ood is not packaged correctly 37 Solutions ae It may take up to 24 hours for each compartment to reach the desired temperature Rearrange items to allow air to flow throughout the compartment Refer to the Airflow diagram in the Using Your Refrigerator section When the doors are opened often or for long periods of time warm humid air enters the compartment This raises the temperature and moisture level within the compartment To lessen the effect reduce the frequency and duration of door openings The refrigerator should not be operated in temperatures ab
10. in the Refrigeration Installation section to level refrigerator Clean the gaskets and the surfaces that they touch Rub a thin coat of appliance polish or kitchen wax on the gaskets after cleaning When you open the door warmer air enters the refrigerator As the warm air cools it can create a vacuum If the door is hard to open wait one minute to allow the air pressure to equalize then see if it opens more easily Refer to the Leveling and Door Alignment section lt may be necessary to add shims under the leveling legs or rollers to complete installation Refer to the Light Bulb Replacement section Refer to the Light Bulb Replacement section Your Home For troubleshooting product manuals and expert advice 9 managemylife www managemylife com For repair in your home of all major brand appliances lawn and garden equipment or heating and cooling systems no matter who made it no matter who sold it For the replacement parts accessories and owner s manuals that you need to do it yourself For Sears professional installation of home appliances and items like garage door openers and water heaters 1 800 4 MY HOME 1 800 469 4663 Call anytime day or night U S A and Canada www sears com www sears ca Our Home For repair of carry in items like vacuums lawn equipment and electronics call anytime for the location of your nearest Sears Parts amp Repair Service Center 1 800 4
11. or auto paste wax Apply wax with a clean soft cloth For products with a stainless steel exterior use a clean sponge or soft cloth and a mild detergent in warm water Do not use abrasive or harsh cleaners Dry thoroughly with a soft cloth CARE AND CLEANING 31 INSIDE WALLS allow freezer to warm up so the cloth will not stick To help remove odors you can wash the inside of the refrigerator with a mixture of baking soda and warm water Mix 2 tablespoons of baking soda to 1 quart of water 26 g soda to 1 liter water Be sure the baking soda is completely dissolved so it does not scratch the surfaces of the refrigerator ACAUTION While cleaning the inside do not spray water DOOR LINERS AND GASKETS Use a clean sponge or soft cloth and a mild detergent in warm water Do not use cleaning waxes concentrated detergents bleaches or cleaners containing petroleum on plastic refrigerator parts PLASTIC PARTS Covers and Panels Use a clean sponge or soft cloth and a mild detergent in warm water Do not use window sprays abrasive cleansers or flammable fluids These can scratch or damage the material CONDENSER COILS Use a vacuum cleaner with an attachment to clean the condenser cover and vents Do not remove the panel covering the condenser coil area LIGHT BULB REPLACEMENT AWARNING Electrical Shock Hazard Before replacing a burned out light bulb either unplug the refrigerator or turn
12. outlet rated for 115 Volts 60 Hz AC only and fused at 15 or 20 amperes This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires It is recommended that a separate circuit serving only this appliance be provided Use a receptacle that cannot be turned off with a switch or pull chain Do not use an extension cord Where a standard two prong wall outlet is encountered it is your personal responsibility and obligation to have it replaced with a properly grounded three prong wall outlet USE OF EXTENSION CORDS Because of potential safety hazards under certain conditions the use of an extension cord is not recommended However if you still elect to use an extension cord it is absolutely necessary that it be a UL listed USA 3 wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes minimum and 120 volts Use of an extension cord will increase the clearance needed for the back of the refrigerator PARTS AND FEATURES Use this page to become more familiar with the parts and features of your refrigerator Page references are included for your convenience NOTE This guide covers several different models The refrigerator you have purchased may have some or all of the items
13. power cords that Keep fingers out of pinch point areas clearances have become frayed or otherwise damaged Do not between the doors and cabinets are necessarily small use a cord that shows cracks or abrasion damage Be careful closing doors when children are in the area along its length or at either the plug or connector end e Unplug your refrigerator before cleaning or making Do not modify or extend the power cord length It any repairs could cause electric shock or fire e When moving your refrigerator away from the wall be NOTE It is strongly recommended that any service be careful not to roll over or damage the power cord performed by a qualified technician SAVE THESE INSTRUCTIONS A WARNING Before replacing a burned out or broken light bulb unplug the refrigerator or turn off power at the circuit breaker or fuse box in order to avoid contact with a live wire filament A burned out light bulb may break when being replaced exposing the wire filament NOTE Some models have LED interior lighting and service should be performed by a qualified technician WARNING Setting either or both controls to the OFF position does not remove power to the light circuit When you are finished reconnect the refrigerator to the electrical source and reset the controls Thermostat Refrigerator Control and or Freezer Control depending on the model to the desired setting This refrigerator must be properly in
14. seconds A CAUTION Demo Mode For store use only The Demo Mode disables all cooling in the refrigerator and freezer sections to conserve energy while on display in a retail store To deactivate Demo Mode With the refrigerator door opened press and hold the Refrigerator Temp and Ultra Ice buttons at the same time for five seconds The control panel will beep to confirm that the Demo Mode is deactivated Power Saving Mode When the refrigerator is in the Power Saving Mode the display will remain off until a door is opened or a button is pressed Once on the display will remain on for 20 seconds To deactivate the Power Saving Mode press the Freezer Temp and Ultra Ice buttons at the same time and hold them for approximately five seconds until the tone sounds 19 AIRFLOW Be sure not to block vents while packing your refrigerator Doing so will restrict airflow and may cause the refrigerator temperature to become too warm or cause interior moisture buildup See air flow diagram below IN DOOR ICE BIN A CAUTION Keep hands and tools out of the ice compartment door and dispenser chute Damage or personal injury may result The icemaker will stop producing ice when the ice bin is full If you need more ice empty the ice bin into the extra ice bin in the freezer compartment Duri
15. supply and contact Sears Home Service at 1 800 4 MY HOME 22 WHEN YOU SHOULD SET THE ICEMAKER POWER SWITCH TO OFF O When the water supply will be shut off for several hours When the ice bin is removed for more than one or two minutes When the refrigerator will not be used for several days NOTE The ice bin should be emptied when the icemaker ON OFF switch is turned to the OFF position NORMAL SOUNDS YOU MAY HEAR The icemaker water valve will buzz as the icemaker fills with water If the power switch is in the ON 1 position it will buzz even if it has not yet been hooked up to water To stop the buzzing move the power switch to OFF 0 NOTE Keeping the power switch in the ON I position before the water line is connected can damage the icemaker You will hear the sound of cubes dropping into the bin and water running in the pipes as the icemaker refills PREPARING FOR VACATION Set the icemaker power switch to OFF O and shut off the water supply to the refrigerator NOTE The ice bin should be emptied anytime the icemaker ON OFF switch is turned to the OFF O position If the ambient temperature will drop below freezing have a qualified technician drain the water supply system to prevent serious property damage due to flooding caused by ruptured water lines or connections FOOD STORAGE GUIDE Wrap or store food in the refrigerator in airtight and moisture proof mater
16. the life of your new product Here s what the Agreement includes Parts and labor needed to help keep products operating properly under normal use not just defects Our coverage goes well beyond the product warranty No deductibles no functional failure excluded from coverage real protection Expert service by a force of more than 10 000 authorized Sears service technicians which means someone you can trust will be working on your product Unlimited service calls and nationwide service as often as you want us whenever you want us e No lemon guarantee replacement of your covered product if four or more product failures occur within twelve months Product replacement if your covered product can t be fixed Annual Preventive Maintenance Check at your request no extra charge Fast help by phone we call it Rapid Resolution phone support from a Sears representative on all products Think of us as a talking owner s manual e Power surge protection against electrical damage due to power fluctuations e 250 Food Loss Protection annually for any food spoilage that is the result of mechanical failure of any covered refrigerator or freezer e Rental reimbursement if repair of your covered product takes longer than promised 10 discount off the regular price of any non covered repair service and related installed parts Once you purchase the Agreement a
17. 15 F 9 C or below It will then begin operation automatically if the icemaker power switch is in the ON I position TROUBLESHOOTING GUIDE HHH COOLING Before conducting troubleshooting make sure that the following basic requirements are met Service Flow 0 5 gpm 1 9 lpm Water Supply Potable Water Water Pressure 20 125 psi 138 862 kPa Operating Ambient Temperature Limits 55 F to 10 F 13 C 43 C 115 Volts 60 Hz AC only and fused Electrical Ratings at 15 or 20 amperes Problem Possible Causes Solutions Refrigerator and The refrigerator control is set to OFF Turn the control ON Refer to the Setting the Controls reezer section are some models section for proper temperature settings not cooling Refrigerator is set to demo mode Demo Mode allows the lights and control display to work normally while disabling cooling to save energy while on the showroom floor Refer to the Setting the Controls section for instructions on how to disable Demo Mode Refrigerator is in the defrost cycle During the defrost cycle the temperature of each compartment may raise slightly Wait 30 minutes and confirm the proper temperature has been restored once the defrost cycle has completed Refrigerator was recently installed It may take up to 24 hours for each compartment to reach the desired temperature Refrigerator was recentl
18. 88 1222 U S A 1 800 469 4663 Canada www sears com www sears ca To purchase a protection agreement on a product serviced by Sears 1 800 827 6655 U S A 1 800 361 6665 Canada Para pedir servicio de reparacion Au Canada pour service en fran ais a domicilio y para ordenar piezas 1 800 LE FOYER 1 888 SU HOGAR 1 800 533 6937 1 888 784 6427 www s ars ca Sears Registered Trademark Trademark of KCD IP LLC in the United States or Sears Brands LLC in other countries Marca Registrada Marca de Fabrica de KCD IP LLC en Estados Unidos o Sears Brands LLC in otros paises MC Marque de commerce P Marque d pos e de Sears Brands LLC
19. ATER IIL Solutions If the doors of the unit are opened often ambient air will warm the refrigerator which will prevent the unit from maintaining the set temperature Lowering the refrigerator temperature can help as well as not opening the doors as frequently If the doors are not properly closed ice production will be affected See the Doors will not close completely or pop open section in Parts amp Features Troubleshooting for more information The recommended temperature for the freezer compartment for normal ice production is O F If the freezer temperature is warmer ice production will be affected It is recommended that you replace the water filter Approximately every six months e When the water filter indicator turns on When the water dispenser output decreases When the ice cubes are smaller than normal Reverse osmosis filtration systems can reduce the water pressure below the minimum amount and result in icemaker issues If the problem persists it may be necessary to contact a plumber The water pressure must be between 20 and 125 psi on models without a water filter and between 40 and 125 psi on models with a water filter If the problem persists it may be necessary to contact a plumber Ice will not dispense if any of the refrigerator doors are left open Infrequent use of the ice dispenser will cause the cubes to stick together over
20. Normal Operation Normal Operation To eliminate the noise make sure that the sides and back cannot vibrate against any wall or cabinet Normal Operation Normal Operation Solutions Problem Doors will not close correctly or pop open Doors are difficult to open Refrigerator wobbles or seems unstable Refrigerator lights do not work Freezer lights do not work Possible Causes open Ice bin crisper cover pans shelves door bins or baskets are out of position The doors were removed during product installation and not properly replaced Refrigerator is not leveled properly The gaskets are dirty or sticky Door was recently closed Leveling legs are not adjusted properly Floor is not level The refrigerator compartment lamp is LED interior lighting and service should be performed by a qualified technician The freezer compartment light bulb may need to be changed 43 ood packages are blocking the door PARTS amp FEATURES IH Solutions Rearrange food containers to clear the door and door shelves Push bins all the way in and put crisper cover pans shelves and baskets into their correct positions See the Using Your Refrigerator section for more information Remove and replace the doors according to the Removing and Replacing Refrigerator Handles and Doors section See Door Alignment
21. Use amp Care Guide Manual de Uso y Cuidado Guide d Utilisation et d Entretien English Espa ol Fran ais Models Modelos Mod les 795 7202 Kenmore UP r Inferior x gerateur z color number numero de color le num ro de la couleur P N MFL62184420 Sears Brands Management Corporation Hoffman Estates IL 60179 U S A www kenmore com www sears com Sears Canada Inc Toronto Ontario Canada M5B 2C3 WWW Sears ca TABLE OF CONTENTS WELTON AE A e aoa oe 3 Protection Agreements lt sesseseseseseseeesms 4 Important Safety Instructhions css 5 7 Electrical amp Grounding Requirements 7 Parts and Features cccccccccccccccccecceccceceeeesae 8 Refrigerator Installation 9 17 Unpacking Your Refrigerator 9 Insta NI iia 10 Removing Replacing Refrigerator Freezer Handles and DOoOrS swwwesesesmmssmmsse 11 14 Removing Installing Freezer Drawers 15 16 Leveling and Door Alignment s 17 Using Your Refrigerator 18 27 Setting the Controls ssssees0ese 18 19 In Door lce Bin ccnesccrntsiun nc ateawia ns 20 Automatic ICemaker sssveseece 21 22 Food Storage Guide cccceccccceccccecccccocaoe 23 gt Refrigerator Section Water Dispenser s
22. ap over the adhesive with your fingers Wipe with warm water and dry Do not use sharp instruments rubbing alcohol flammable fluids or abrasive cleaners to remove tape or glue These products can damage the surface of your refrigerator Refrigerator shelves are installed in the shipping position Please reinstall shelves according to your individual storage needs BASE GRILLE INSTALLATION To remove the base grille 1 Open the clarity reezer Drawer Drawer not shown for 2 Once the drawer is open and there is sufficient clearance remove the screws on the top of the cover To replace the base grille Place the cover into position and then insert and tighten the screws PRIOR TO USE 1 Clean your refrigerator thoroughly and wipe off all dust that accumulated during shipping 2 Install accessories such as ice cube bin drawers shelves etc in their proper places They are packed together to prevent possible damage during shipment 3 Allow your refrigerator to run for at least two to three hours before putting food in it Check the flow of cold air in the freezer compartment to ensure proper cooling Your refrigerator is now ready for use INSTALLATION The refrigerator should always be plugged into its own individual properly grounded electrical outlet rated for 115 Volts 60 Hz AC only and fused at 15 or 20 amperes This provides the best performance and also prevents ove
23. artridge ears so that it can be inserted into the filter head Separate red cap 28 3 Twist the cartridge to the right about 1 4 of a turn You will feel a stop and the locked symbol should now be lined up with the indicator line Wa gt gt gt gt gt gt 2 2 22 After the water filter is replaced dispense 2 5 gallons of water flush for approximately 5 minutes to remove trapped air and contaminates from the system Do not dispense the entire 2 5 gallon amount continuously Depress and release the dispenser pad for cycles of 30 seconds ON and 60 seconds OFF After changing the filter press and hold the FILTER button for 3 seconds to turn the indicator light off NOTE To purchase a replacement water filter visit a Sears store or call 1 800 4 MY HOMES Also you may order on line at www sears com partsdirect Performance Data Sheet Model GEN11042F 08 Use Replacement Cartridge GEN11042FR 08 The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system as specified in NSF ANSI Standard 42 System tested and certified by NSF International against NSF ANSI Standard 42 for the reduction of substances listed below Capacity 500 Gallons 1 892 Liters C
24. artsdirect Protect filter from freezing Remove filter in temperatures SAFETY INFORMATION below SE EUS Read understand and follow all safety information Do not install on hot water supply lines The maximum contained in these instructions prior to use of the operating water temperature of this filter system is 100 F KENMORE Model GEN11042F 08 drinking water 378 C system Retain these instructions for future reference Do not install if water pressure exceeds 125 psi 862 kPa If your water pressure exceeds 80 psi 552 kPa you must install a pressure limiting valve Contact a plumbing professional if you are uncertain how to check your water Intended Use The KENMORE Model GEN11042F 08 drinking water system is intended for use in filtering contaminants from drinking water as listed on the Performance Data Sheet WAWA WA and has not been evaluated for other uses The system Do not install where water hammer conditions may is installed inside the refrigerator and must be installed occur If water hammer conditions exist You must install a operated and maintained as specified in the installation water hammer arrester Contact a plumbing professional and use instructions if you are uncertain how to check for this condition Where a backflow prevention device is installed on a water system a device for controlling pressure due to thermal expansion must be installed The disposable filter cartridge MUST b
25. connectall vire namics 4 may be injured or receive an electrical shock 5 Remove the grounding screw 5 6 Rotate hinge lever 6 counterclockwise Lift the top hinge 7 free of the hinge lever latch 8 NOTE Be careful when you work with the hinge and base grille You may be injured CAUTION When lifting the hinge free of the latch be careful that the door does not fall forward To remove the left refrigerator door 7 Lift the door from the middle hinge pin and remove the On the back of the refrigerator pull the water tube out of door the collet fitting on the connector by pressing the fitting 8 Place the door inside facing up on a non scratching release ring see picture below surface To remove the right refrigerator door 1 Open the door Remove the top hinge cover screw 1 Lift up cover 2 Remove cover Disconnect wire harness 3 Remove the grounding screw 4 Rotate hinge lever 5 clockwise Lift top hinge 6 free of hinge lever latch 7 6 Remove the door by lifting it off the middle hinge pin located at the bottom of the door 7 Place the door on a soft smooth surface with the inside up to prevent damage A CAUTION When lifting the hinge free of the latch be careful that the door does not fall forward OM l O bh 13 Reinstalling the Refrigerator Door gt Right Door Left Door 1 Lower the door onto mi
26. control on some models will also click when cycling on and off Rattling noises may come from the flow of refrigerant the water line on the back of the unit or items stored on top of or around the refrigerator Refrigerator is not resting solidly on the floor Refrigerator with linear compressor was jarred while running Evaporator fan motor is circulating air through the refrigerator and freezer compartments Air is being forced over the condenser by the condenser fan Refrigerant flowing through the cooling system Contraction and expansion of the inside walls due to changes in temperature Water dripping on the defrost heater during a defrost cycle If the side or back of the refrigerator is touching a cabinet or wall some of the normal vibrations may make an audible sound Water running into the drain pan during the defrost cycle Your refrigerator is designed to run more efficiently to keep your food items at the desired temperature The high efficiency compressor may cause your new refrigerator to run longer than your old one but it is still more energy efficient than previous models While the refrigerator is running it is normal to hear a pulsating or high pitched sound 42 Normal Operation Normal Operation Floor is weak or uneven or leveling legs need to be adjusted See the Door Alignment section Normal Operation Normal Operation Normal Operation Normal Operation
27. ddle hinge pin 9 1 Lower the door onto middle hinge pin 10 2 Fit top hinge 6 over hinge lever latch 7 and into OF irom hinge 71 over hinge lever laich Erandina pace Rotate lever 5 counterclockwise to secure place Rotate lever 6 clockwise to secure hinge nge 3 Install the grounding screw 4 and connect wire 3 Install the grounding screw 5 and connect the two harnesses 3 wire harnesses 4 Pere MONA ai Hook tab on switch side of corner under edge of wire 4 Push the water tube 3 located at the top of the lef opening in cabinet top Poston cover 2 into place the cabinet until it exits through the back PESTI AMENO MEN OYES 5 Insert the water supply tube 3 into the connector until you see only one scale mark Fully insert the tube over s in 15 mm 6 Hook tabs on left side of hinge cover 1 under the edge of the top hinge 7 and position the cover in place Insert and tighten the cover screw 1 ACAUTION Collet Tube M After inserting pull the tube to make sure that it is secure and reinsert the clip Scale Mark Clip 14 HOW TO REMOVE THE FREEZER DRAWER WARNING Use two or more people to remove and With both hands grasp the sides of the door and pull install the freezer drawer Failure to do so can result it up to separate it from the rails personal injury or product damage
28. e replaced every six months at the rated capacity or sooner if a noticeable reduction in flow rate occurs State of California Department of Public Health Water Treatment Device Certificate Number 09 2019 Date Issued December 15 2009 Sears Roebuck ane Manufacturer wh 1 ae A Mi Contaminants T p yi BI 1 i yee vi b j Atr zine Benzene Carbofiii Lindane p Dichlorobenzene Toxaphene Rated Service Capacity 200 gal service Flow 0 5 gpm 30 AWARNING Explosion Hazard Use non flammable cleaner Failure to do so can result in fire explosion or death Both the refrigerator and freezer sections defrost automatically however clean both sections about once a month to prevent odors Wipe up spills immediately GENERAL CLEANING TIPS e Unplug refrigerator or disconnect power Remove all removable parts such as shelves crispers etc Refer to sections in Using Your Refrigerator for removal instructions e Use a clean sponge or soft cloth and a mild detergent in warm water Do not use abrasive or harsh cleaners Hand wash rinse and dry all surfaces thoroughly Plug in refrigerator or reconnect power EXTERIOR Waxing external painted metal surfaces helps provide rust protection Do not wax plastic parts Wax painted metal surfaces at least twice a year using appliance wax
29. ecessary to contact a plumber It is recommended that you replace the water filter Approximately every six months When the water filter indicator turns on When the water dispenser output decreases When the ice cubes are smaller than normal The water pressure must be between 20 and 125 psi on models without a water filter and between 40 and 125 psi on models with a water filter If the problem persists it may be necessary to contact a plumber Reverse osmosis filtration systems can reduce the water pressure below the minimum amount and result in icemaker issues Refer to Water Pressure section The tubing can kink when the refrigerator is moved during installation or cleaning resulting in reduced water flow Straighten or repair the water supply line and arrange it to prevent future kinks Problem Icemaker is not making enough ice continued Dispensing water slowly Not dispensing ice Doors are opened often or for long periods of time Doors are not closed completely The temperature setting for the freezer is too warm Water filter has been exhausted Reverse osmosis filtration system is used Low house water supply pressure Doors are not closed completely Infrequent use of the dispenser The delivery chute is clogged with frost or ice fragments The dispenser display is locked Ice bin is empty 39 ICE 8 W
30. efrigerator has not been used for a long time Never store beverage cans or other items in the ice bin for the purpose of rapid cooling Doing so may damage the icemaker or the containers may burst If discolored ice is dispensed check the water filter and water supply If the problem continues contact a Sears or other qualified service center Do not use the ice or water until the problem is corrected Keep children away from the dispenser Children may play with or damage the controls The ice passage may become blocked with frost if only crushed ice is used Remove the frost that accumulates by removing the ice bin and clearing the passage with a rubber spatula Dispensing cubed ice can also help prevent frost buildup Never use thin crystal glass or crockery to collect ice Such containers may chip or break resulting in glass fragments in the ice Dispense ice into a glass before filling it with water or other beverages Splashing may occur if ice is dispensed into a glass that already contains liquid Never use a glass that is exceptionally narrow or deep Ice may jam in the ice passage and refrigerator performance may be affected Keep the glass at a proper distance from the ice outlet A glass held too close to the outlet may prevent ice from dispensing To avoid personal injury keep hands out of the ice door and passage Never remove the dispenser cover If ice or water dispenses unexpectedly turn off the water
31. embly Hole Lower door into final position and tighten the screws 3 With the drawer pulled out to full extension insert the lower basket 4 in the rail assembly A WARNING If the Durabase divider is removed there is enough open space for children or pets to crawl inside To prevent accidental child and pet entrapment or suffocation risk DO NOT allow them to touch or go near the freezer drawer WARNING DO NOT step or sit down on freezer drawer 16 LEVELING AND DOOR ALIGNMENT 3 Open both doors again and check to make sure that they close easily If the doors do not close easily tilt Leveling the refrigerator slightly more to the rear by turning After installing plug the refrigerator s power cord into a both leveling legs to the left It may take several more 3 prong grounded outlet and push the refrigerator into the turns and you should turn both leveling legs the same final position amount Your refrigerator has two front leveling legs one on the 4 Replace the base grille right and one on the left Adjust the legs to alter the tilt from front to back or side to side If your refrigerator seems unsteady or you want the doors to close more easily adjust the refrigerator s tilt using the instructions NOTE Your refrigerator is uniquely designed with two fresh food doors Either door can be opened or closed independently of the other You may have to exert sligh
32. ervice call 1 800 4 MY HOME 1 800 469 4663 For one year from the date of purchase free repair will be provided if any non consumable part of this appliance fails due to defective materials or workmanship This coverage applies for only 90 days from the purchase date if this product is ever used for other than private household purposes For ten years from the date of purchase a defective compressor will be repaired free of charge This coverage applies for only two years from the date of purchase if this appliance is ever used for other than private household purposes This warranty covers only defects in material and workmanship and will NOT pay for 1 Consumable parts that can wear out from normal use including but not limited to filters belts light bulbs and bags 2 A service technician to instruct the user in correct product installation operation or maintenance 3 A service technician to clean or maintain this product 4 Damage to or failure of this product if it is not installed operated or maintained according to the all instructions supplied with the product 5 Damage to or failure of this product resulting from accident abuse misuse or use for other than its intended purpose 6 Damage to or failure of this product caused by the use of detergents cleaners chemicals or utensils other than those recommended in all instructions supplied with the product 7 Damage to or failure of parts
33. eset button for three seconds to turn the indicator light off You need to change the water filter approximately every six months Dispenser Light To turn the dispenser light on and off press the Light button Door Alarm When power is connected to the refrigerator the door alarm is initially set to ON When you press and hold the Door Alarm button the display will change to O and the Door Alarm function will deactivate When either the refrigerator or the freezer door is left open for more than 60 seconds the alarm tone will sound to let you know that the door is open When you close the door the door alarm will stop Control Lock When power is initially connected to the refrigerator the Control Lock function is off f you want to activate the Control Lock function to lock other buttons press and hold the Door Alarm button for approximately three seconds The Lock ON icon will display and the Control Lock function is now enabled When the Control Lock function is activated no other buttons will work The dispenser pad is also deactivated To disable the Control Lock function press and hold the Door Alarm button for approximately three seconds Temperature Mode Switch Function F lt gt C If you want to convert F to C or vice versa press and hold the Freezer Temp and Refrigerator Temp buttons at the same time for approximately five
34. et for water dispensing Refrigerator or freezer doors are not closed properly Water filter has been recently removed or replaced Tubing connecting refrigerator to house supply valve is kinked The house water supply is not connected the valve is not turned on fully or the valve is clogged 40 Solutions lt may take up to 24 hours for each compartment to reach the desired temperature and for the icemaker to begin making ice Locate the icemaker ON OFF switch and confirm that it is in the ON I position Foreign substances or frost on the ice detecting sensor can interrupt ice production Make sure that the sensor area is clean at all times for proper operation Connect refrigerator to the water supply and turn the water shutoff valve fully open If your icemaker is equipped with an ice shutoff arm make sure that the arm moves freely If your icemaker is equipped with the electronic ice shutoff sensor make sure that there is a clear path between the two sensors Reverse osmosis filtration systems can reduce the water pressure below the minimum amount and result in icemaker issues Refer to the Water Pressure section Dispense 2 5 gallons of water flush for approximately 5 minutes to remove trapped air and contaminates from the system Do not dispense the entire 2 5 gallon amount continuously Depress and release the dispenser pad for cycles of 30 seconds ON and 60
35. etting the Controls section 3 Clean the refrigerator wipe it and dry well 4 Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in This stops odor and mold from building up WHEN YOU MOVE When you are moving your refrigerator to a new home follow these steps to prepare it for the move 1 Remove all food from the refrigerator and pack alll frozen food in dry ice 2 Unplug the refrigerator 3 Clean wipe and dry thoroughly 4 Take out all removable parts wrap them well and tape them together so they do not shift and rattle during the move Refer to the Using your Refrigerator section for removable instructions 5 Depending on the model raise the front of the refrigerator so it rolls easier OR screw in the leveling legs all the way so they do not scrape the floor See the Door Closing section 6 Tape the doors shut and tape the power cord to the refrigerator cabinet When you get to your new home put everything back and refer to the Refrigerator Installation section for preparation instructions 32 CONNECTING THE WATER LINE BEFORE YOU BEGIN WHAT YOU WILL NEED This water line installation is not covered by the refrigerator Copper Tubing 1 4 in outer warranty Follow these instructions carefully to minimize the diameter to connect the refrigerator risk of expensive water damage to the water supply Be sure both ends of the tubing a
36. ftovers with plastic wrap aluminum foil or plastic containers with tight lids 23 STORING FROZEN FOOD NOTE Check a freezer guide or a reliable cookbook for further information about preparing food for freezing or food storage times Freezing Your freezer will not quick freeze a large quantity of food Do not put more unfrozen food into the freezer than will freeze within 24 hours no more than 2 to 3 Ibs of food per cubic foot of freezer space Leave enough space in the freezer for air to circulate around packages Be careful to leave enough room at the front so the door can close tightly Storage times will vary according to the quality and type of food the type of packaging or wrap used how airtight and moisture proof and the storage temperature Ice crystals inside a sealed package are normal This simply means that moisture in the food and air inside the package have condensed creating ice crystals NOTE Allow hot foods to cool at room temperature for 30 minutes then package and freeze Cooling hot foods before freezing saves energy Packaging Successful freezing depends on correct packaging When you close and seal the package it must not allow air or moisture in or out If it does you could have food odor and taste transfer throughout the refrigerator and could also dry out frozen food Packaging recommendations Rigid plastic containers with tight fitting lids e Straight sided canning freezing jars
37. hooks into the slots at a desired height individ 4 g ds Y et h Then lower the front of the shelf so that the hooks your individual storage needs Your model may have glass drop into the slots or wire shelves Adjusting the shelves to fit different heights of items will make finding the exact item you want easier Doing so will also reduce the amount of time the refrigerator door is open which will save energy IMPORTANT Do not clean glass shelves with warm water while they are cold Shelves may break if exposed to sudden temperature changes or impact NOTE Glass shelves are heavy Use special care when removing them Adjusting Shelves Cantilever Remove shelves from the shipping position and replace shelves in the position you want CAUTION Make sure that shelves are level from one To remove a shelf Tilt up the front of the shelf in the side to the other Failure to do so may result in the shelf direction of 1 and lift it in the direction of 2 Pull falling or spilling food the shelf out 25 HUMIDITY CONTROLLED CRISPER The crispers provide fresher tasting fruit and vegetables by letting you easily control humidity inside the drawer You can control the amount of humidity in the moisture sealed crispers by adjusting the control to any setting between HIGH and LOW HIGH keeps moist air in the crisper for best storage of fresh leafy vegetables LOW lets moist air out of
38. ial unless otherwise noted This prevents food odor and taste transfer throughout the refrigerator or dated products check date code to ensure freshness ltems Butter or margarine How to gt Keep opened butter in a covered dish or closed compartment When storing an extra supply wrap in freezer packaging and freeze Cheese Milk Eggs Fruit Leafy vegetables Vegetables with skins carrots peppers P gt Store in the original wrapping until you are ready to use it Once opened rewrap tightly in plastic wrap or aluminum foil gt Wipe milk cartons For best storage place milk on interior shelf not on door shelf gt Store in original carton on interior shelf not on door shelf gt Do not wash or hull the fruit until it is ready to be used Sort and keep fruit in its original container in a crisper or store in a completely closed paper bag ona refrigerator shelf gt gt Remove store wrapping and trim or tear off bruised and discolored areas Wash in cold water and drain Place in plastic bag or plastic container and store in crisper Place in plastic bags or plastic container and store in crisper Fish b gt Store fresh fish and shellfish in the freezer section if they are not being consumed the same day of purchase lt is recommended to consume fresh fish and shellfish the same day purchased Leftovers gt gt Cover le
39. ing codes osmosis remains call a licensed qualified plumber NOTE A Self Piercing Saddle Type Water Valve should All installations must be in accordance with local not be used plumbing code requirements CAUTION Wear eye protection during installation to A WARN NG prevent injury R Electrical Shock Hazard When using any electrical device such as a power drill during installation be sure the device is battery powered double insulated or grounded in a manner that will prevent the hazard of electric shock 33 INSTALLATION INSTRUCTIONS 5 TIGHTEN THE PIPE CLAMP Tighten the clamp screws until the sealing washer Install the shutoff valve on the nearest frequently used begins to swell drinking water line 1 SHUT OFF THE MAIN WATER SUPPLY Turn on the nearest faucet to relieve the pressure on the line 2 CHOOSE THE VALVE LOCATION Choose a location for the valve that is easily accessible lt is best to connect into the side of a vertical water pipe When it is necessary to connect into a horizontal water pipe make the gt NOTE Do not overtighten clamp or you may crush the tubing Washer connection to the top or side rather than at the bottom to avoid drawing off any sediment from the water pipe 6 ROUTE THE TUBING Route the tubing between the cold water line and the 3 DRILL THE HOLE FOR THE VALVE refrigerator Drill a 1 4 in hole in the water pipe using a sharp bit Remo
40. ltration system is connected F h s a enn atthe YA to your cold water supply this water line installation is not end you will need an adapter covered by the refrigerator warranty Follow the following lt d k full inimize the risk of available at plumbing supply instructions carefully to minimize the risk of expensive water stores to connect the water line damage to the refrigerator OR you can If a reverse osmosis water filtration system is connected cut off the flared fitting with to your cold water supply the water pressure to the reverse a tube cutter and then use a osmosis system needs to be a minimum of 40 to 60 psi 2 8 compression fitting kgf cm 4 2 kgf cm less than 2 0 3 0 sec to filla cup e Shutoff valve to connect of 7 oz capacity to the cold water line The If the water pressure from the reverse osmosis system is less shutoff valve neue have a water inlet with a minimum than 21 psi or 1 5 kgf cm2 takes more than 4 0 sec to fill a inside diameter of 3 32 in at the point of connection anet AA to the COLD WATER LINE E Saddle type shutoff valves Check to see if the sediment filter in the reverse osmosis are included in many water system is blocked Replace the filter if necessary supply kits Before purchasing Allow the storage tank on the reverse osmosis system to make sure a saddle type refill after heavy usage valve complies with your local If the issue concerning water pressure from reverse plumb
41. ng use the ice can become uneven causing the icemaker to misread the amount of ice cubes and stop producing ice Shaking the ice bin to level the ice within it can reduce this problem NOTE Storing cans or other items in the ice bin will damage the icemaker Keep the ice compartment door closed tightly If the ice compartment door is not closed tightly the cold air in the ice bin will freeze food in the refrigerator compartment This could also cause the icemaker to not produce ice NOTE To prevent ice cubes from melting and leaking from the dispenser ALWAYS empty the ice bin when the icemaker is set to Off O for more than a few minutes 1 Push on the latch firmly where noted to close the ice compartment door It will make a clicking sound when it is completely closed fr 20 2 To remove the in door ice bin grip the front handle slightly lift the lower part and slowly pull out the bin as shown NX 3 To reinstall the in door ice bin slightly slant the bin during replacement to avoid contact with the icemaker a 4 Avoid touching the ice detecting sensor when replacing the ice bin See the label on the ice compartment door for details Gu a B Automatic PI I gt Shutoff Arm
42. off power at the circuit breaker or fuse box NOTE The refrigerator compartment lights Have LED interior lighting and service should be performed by a qualified technician CHANGE FREEZER COMPARTMENT LIGHT BULB 1 Unplug refrigerator power cord form outlet 2 Remove the screw using a Phillips screwdriver 3 Grasp the light cover and pull the cover downward CAUTION Make sure that the bulb is cool to the touch 4 Rotate the bulb counterclockwise to remove 5 Replace with a new 60 watt appliance bulb 6 Insert tabs on back of cover into slots in freezer ceiling Push cover up to snap front into place 7 Tighten the screw using a Phillips screwdriver POWER INTERRUPTIONS 1 If the power will be out for 24 hours or less keep all refrigerator doors closed to help foods stay cold and frozen 2 f the power will be out for more than 24 hours remove all food and store it in a different refrigerator or frozen food locker WHEN YOU GO ON VACATION If you choose to leave the refrigerator on while you are away follow these steps to prepare your refrigerator before you leave 1 Use up any perishables and freeze other items 2 Turn off the icemaker and empty the ice bin If you choose to turn the refrigerator off before you leave follow these steps 1 Remove all food from the refrigerator 2 Depending on your model set the thermostat control refrigerator control to OFF See the S
43. ons at right to help prevent accidents child entrapment and suffocation BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER Take off the doors Leave the shelves in place so that children may not easily climb inside CFC HCFC DISPOSAL Your old refrigerator may have a cooling system that used CFCs or HCFCs chlorofluorocarbons or hydrochlorofluorocarbons CFCs and HCFCs are believed to harm stratospheric ozone if released to the atmosphere Other refrigerants may also cause harm to the environment if released to the atmosphere If you are throwing away your old refrigerator make sure the refrigerant is removed for proper disposal by a qualified technician If you intentionally release refrigerant you may be subject to fines and imprisonment under provisions of environmental legislation ELECTRICAL amp GROUNDING REQUIREMENTS IMPORTANT Please read carefully TO CONNECT ELECTRICITY A WARNING Electrical Shock Hazard FOR PERSONAL SAFETY this appliance must be properly grounded Have the wall outlet and the circuit checked by a qualified electrician to make sure the outlet is properly grounded 3 prong grounding type wall receptacle grounding plug Ensure proper ground exists before use RECOMMENDED GROUNDING METHOD The refrigerator should always be plugged into its own individual properly grounded electrical
44. ontaminant Reduction Determined by NSF testing x Average Influent Challenge Average Product Average Max Effluent Min Required Contaminant Reduction A 2 k Influent Concentration Water Concentration Reduction Mg L Reduction Chlorine Taste and Odor 2 0 mg L 2 0 mg L 10 mg L 974 0 06 mg L 2 50 Nominal Particulate Class Ill 48 000 pts mL At least 10 000 particles mL 75 mg L 99 9 26 mg L 285 2 5 0 to lt 15 0 Um Application Guidelines Water Supply Parameters 0 5 gpm 1 89 Ipm lt AWARNING To reduce the risk associated with ingestion of contaminants 20 125 psi 138 862 kPa 34 F 100 F 1 1 C 37 8 C Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before and after the system It is essential that the manufacturer s recommended installation maintenance and filter replacement requirements be carried out for the product to perform as ACAUTION advertised NOTE While the testing was performed under standard To reduce risk of property damage due to water leakage laboratory conditions actual performance may vary Read and follow Use Instructions before installation and Replacement Cartridge GEN11042FR 08 use of this system To purchase a replacement filter visit your local Sears Installation and use MUST comply with all state and local store or call 1 800 4 MY HOME Visit us on the web at plumbing codes www sears com p
45. or systems resulting from unauthorized modifications made to this product Disclaimer of implied warranties limitation of remedies Customer s sole and exclusive remedy under this limited warranty shall be product repair as provided herein Implied warranties including warranties of merchantability or fitness for a particular purpose are limited to one year or the shortest period allowed by law Sears shall not be liable for incidental or consequential damages Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages or limitation on the duration of implied warranties of merchantability or fitness so these exclusions or limitations may not apply to you This warranty applies only while this appliance is used in the United States or Canada This warranty gives you specific legal rights and you may also have other rights which vary from state to state Sears Brands Management Corporation Hoffman Estates IL 60179 Sears Canada Inc Toronto Ontario Canada M5B 2C3 PROTECTION AGREEMENTS Master Protection Agreements Congratulations on making a smart purchase Your new Kenmore Elite product is designed and manufactured for years of dependable operation But like all products it may require preventive maintenance or repair from time to time That s when having a Master Protection Agreement can save you money and aggravation The Master Protection Agreement also helps extend
46. out 2 To replace insert the Durabase in rail assembly 2 To replace slightly tilt up the drawer front insert drawer into the frame and push drawer back into place DURABASE DIVIDER The Durabase divider allows you to organize the Durabase area into sections lt can be adjusted from side to side to accommodate items of different sizes AWARNING If the Durabase divider is removed there is enough open space for children or pets to crawl inside To prevent accidental child and pet entrapment or suffocation risk DO NOT allow children or pets to touch or go near the drawer 27 WATER FILTER REPLACING THE WATER FILTER CHANGE FILTER Q Filter Reset HOLD 3 SEC It is recommended that you replace the water filter Approximately every six months When the water filter indicator turns on When the water dispenser output decreases When the ice cubes are smaller than normal NOTE Keep the water filter bypass plug You MUST use the water filter bypass plug when a replacement water filter cartridge is not available 1 Slowly turn the old cartridge to the left When the cartridge is released you will feel it click out of place NOTE Replacing the filter causes a small amount of water around 1 oz or 25 cc to drain J 2 Remove the old cartridge Take the new cartridge out of its packaging and remove the red cap Line up the c
47. ove 110 F Adding food warms the compartment requiring the cooling system to run Allowing hot food to cool to room temperature before putting it in the refrigerator will reduce this effect See the Doors will not close correctly or pop open section in Parts amp Features Troubleshooting If the temperature is too warm adjust the control one increment at a time and wait for the temperature to stabilize Refer to the Setting the Controls section for more information During the defrost cycle the temperature of each compartment may raise slightly and condensation may form on the back wall Wait 30 minutes and confirm the proper temperature has been restored once the defrost cycle has completed When the doors are opened often or for long periods of time warm humid air enters the compartment This raises the temperature and moisture level within the compartment To lessen the effect reduce the frequency and duration of door openings See the Doors will not close correctly section in the Troubleshooting section Humid weather allows additional moisture to enter the compartments when the doors are opened leading to condensation or frost Maintaining a reasonable level of humidity in the home will help to control the amount of moisture that can enter the compartments During the defrost cycle the temperature of each compartment may raise slightly and condensation may form on the back wall Wait 30 minutes and confirm that the p
48. re cut square Water hammer water banging in the pipes in house 2 plumbing can cause damage to refrigerator parts and can To determine how much tubing you lead to water leakage or flooding Call a qualified plumber need measure the distance from the water valve on the to correct water hammer before installing the water supply back of the refrigerator to the water supply pipe Then line to the refrigerator add 8 feet 2 4 m Be sure there is sufficient extra tubing about 8 feet 2 4 m coiled into 3 turns of about 10 in To prevent burns and product damage only connect the 25 cm diameter to allow the refrigerator to move out refrigerator water line to a cold water supply from the wall after installation If you use your refrigerator before connecting the water Power drill line make sure the icemaker power switch is in the OFF O ae e 1 2 in or adjustable wrench position PA Flat blade and Phillips head screwdrivers Do not install the icemaker tubing in areas where temperatures fall below freezing Two 1 4 in outer diameter compression nuts and WATER PRESSURE 2 ferrules sleeves to connect the copper tubing to the shutoff valve and the refrigerator water valve A cold water supply The water pressure must be between 20 and 125 psi on models without a water filter and between 40 and 125 psi on models with a water filter 4 A e f your existing copper water f a reverse osmosis water fi
49. rloading house wiring circuits which could cause a fire hazard from overheated wires It is recommended that a separate circuit serving only this appliance be provided WARNING Shock Hazard To reduce the risk of electric shock do not install the refrigerator in a wet or damp area 10 INSTALLATION continued 1 To avoid noise and vibration the unit must be leveled and installed on a solidly constructed floor If required adjust the leveling legs to compensate for unevenness of the floor The front should be slightly higher than the rear to aid in door closing Leveling legs can be turned easily by tipping the cabinet slightly Turn the leveling legs left to raise the unit or right to lower it See LEVELING AND DOOR ALIGNMENT NOTE Installing on carpeting soft tile surfaces a platform or weakly supported structure is not recommended 2 Install this appliance in an area where the temperature is between 55 F 13 C and 110 F 43 C If the temperature around the appliance is too low or high cooling ability may be adversely affected Select a place where a water supply can be easily connected for the automatic icemaker NOTE The water pressure must be between 20 and 125 psi on models without a water filter and between AO and 125 psi on models with a water filter Too small of a distance from adjacent items may result in lowered freezing capability and increased electricity consumption charges Allow at lea
50. rom illustrations on this page Removing Freezer Drawer Handle Loosen the set screws located on the lower side of the handle with a 1 8 in Allen wrench and remove the handle NOTE If the handle mounting fasteners need to be tightened or removed use a 1 4 in Allen wrench HOW TO REPLACE FREEZER DOOR HANDLE NOTE Handle appearance may vary from illustrations on this page Replacing Freezer Drawer Handle Place the handle on the door by fitting the handle footprints over the mounting fasteners and tightening the set screws with a Ys in Allen wrench NOTE If the handle mounting fasteners need to be tightened or removed use a 1 4 in Allen wrench 12 REMOVING AND REPLACING A CAUTION Before you begin remove food and bins REFRIGERATOR DOORS from the doors A WARNING Excessive Weight Hazard Use two or more people to remove and install the refrigerator doors Failure to do so can result in back or other injury A WARNING Electrical Shock Hazard 1 Open the door Remove the top hinge cover screw 1 Disconnect the electrical supply to the refrigerator Lift up the cover 2 before installing Failure to do so could result in serious injury or death 2 Remove the cover 3 Pull out the tube 3 Do not put hands feet or other objects into the air vents base grille or bottom of the refrigerator You a D
51. roper temperature has been restored once the defrost cycle has completed Food stored uncovered or unwrapped and damp containers can lead to moisture accumulation within each compartment Wipe all containers dry and store food in sealed packaging to prevent condensation and frost Problem Possible Causes _ ood is freezing in the refrigerator compartment rost or ice crystals form on frozen food outside of package Refrigerator or Freezer section is too cold Frost or ice crystals on frozen food inside of sealed package Icemaker is not making enough ice incorrectly Refrigerator is installed in a cold location Door is opened frequently or for long periods of time Door is not closing properly Incorrect temperature control settings ood with high water content was placed near an air vent Refrigerator temperature control is set Condensation from food with a high water content has frozen inside of the food package Food has been left in the freezer for a long period of time Demand exceeds ice storage capacity House water supply is not connected valve is not turned on fully or valve is clogged Water filter has been exhausted Low house water supply pressure Reverse Osmosis filtration system is used Tubing connecting refrigerator to house supply valve is kinked
52. safety messages This is the safety alert symbol lt alerts you to safety messages that inform you of hazards that can kill or hurt you or others or cause damage to the product All safety messages will be preceded by the safety alert symbol and the hazard signal word DANGER WARNING or CAUTION These words mean A DANGER You will be killed or seriously injured if you do not follow instructions A WARN l NG You can be killed or seriously injured if you do not follow instructions Indicates an imminently hazardous situation which if not avoided A CAUTION may result in minor or moderate injury or product damage All safety messages will identify the hazard tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed AWARNING To reduce the risk of fire electric shock or personal DO NOT store or use gasoline or other flammable injury when using your product basic safety precautions vapors and liquids in the vicinity of this or any other should be followed including the following appliance Read all instructions before using this appliance DO NOT allow children to climb stand or hang on the NEVER unplug your refrigerator by pulling on the refrigerator doors or shelves in the refrigerator They power cord Always grip the plug firmly and pull it could damage the refrigerator and seriously injure straight out from the outlet themselves Immediately repair or replace all
53. several hours the first glass dispensed may be warm Discard the first 10 oz Make sure that the refrigerator is connected to a cold water pipe AWARNING Connecting the refrigerator to a hot water line may damage the icemaker A water filter may need to be installed to eliminate taste and odor problems It is recommended that you replace the water filter Approximately every 6 months When the water filter indicator turns on When the water dispenser output decreases When the ice cubes are smaller than normal Dispense 2 5 gallons of water flush for approximately 5 minutes to remove trapped air and contaminates from the system Do not dispense the entire 2 5 gallon amount continuously Depress and release the dispenser pad for cycles of 30 seconds ON and 60 seconds OFF Empty the ice bin If your icemaker is equipped with an ice shutoff arm make sure that the arm moves freely If your icemaker is equipped with the electronic ice shutoff sensor make sure that there is a clear path between the two sensors Reinstall the ice bin and wait 24 hours to confirm proper operation Problem Possible Causes Clicking Rattling Whooshing Gurgling Popping Sizzling Vibrating Dripping Pulsating or High Pitched Sound The defrost control will click when the automatic defrost cycle begins and ends The thermostat control or refrigerator
54. simple phone call is all that it takes to schedule service You can call at any time day or night or schedule a service appointment online The Master Protection Agreement is a risk free purchase If you cancel for any reason during the product warranty period we will provide a full refund or a prorated refund anytime after the product warranty period expires Purchase your Master Protection Agreement today Some limitations and exclusions apply For prices and additional information in the U S A call 1 800 827 6655 Coverage in Canada varies on some items For full details call Sears Canada at 1 800 361 6665 Sears Installation Service For Sears professional installation of home appliances garage door openers water heaters and other major home items in the U S A or Canada call 1 800 4 MY HOME PRODUCT RECORD In the space below record the date of purchase model and serial number of your product You will find the model and serial number printed on an identification label located on the interior liner of the refrigerator compartment ave these items of information available whenever you contact Sears concerning your product Model No Serial No Date of Purchase Save these instructions and attach your sales receipt for future reference IMPORTANT SAFETY INSTRUCTIONS BASIC SAFETY PRECAUTIONS This guide contains many important safety messages Always read and obey all
55. sss ssesseesmeemeese 24 Refrigerator Shelves ou ssssssssssssssssssssseesseesessees 25 Humidity Controlled Crisper 26 Modular Door Bin ss eseesmeeeeemeee 26 Freezer Section DORIS Sassi ia 27 Durabase Divider cccccccccccccececesceeooo 27 Pullout Drawer ccoccceccccocccccccccocscoueoos 27 Water Filter svssssesveseseemso 28 30 Care And Cleaning s s0sc 31 32 General Cleaning Tips ssswsses 31 EXT de P oiriin 31 Inside Walls eseseeseseseesesesoosesossesososoeseeoesesessesoso 31 Door Liner And Gaskets sw ssssessss 31 Plain 3 Condenser CoilS s swssesessemmmmeeemmene 3 Light bulb replacement s ss ve 32 Power Interruptions s sssssesesseese 32 When You Go On Vacation v s s 32 When You MOve ssesmewesewenenesenenzsneo 32 Connecting the Water Line 33 35 Troubleshooting Guide 36 43 SET VICE oi cs ccnsascessssouscstavcsestsociasnsspnsnsves Back Cover WARRANTY REFRIGERATOR WARRANTY Kenmore Limited Warranty When this appliance is installed operated and maintained according to all supplied instructions the following warranty coverage applies To arrange for warranty s
56. st 24 inches 61 cm in front of the refrigerator to open the doors 2 5 08 cm 4 NOTE Removing the doors is always recommended when it is necessary to move the refrigerator through a narrow opening If it is necessary to remove the handles follow the directions below DOO NOTE HOW TO REMOVE REFRIGERATOR HANDLE andle appearance may vary from illustrations on this page Removing Refrigerator Handle Loosen the set screws with a 3 32 in Allen wrench and remove the handle NOTE If the handle mounting fasteners need to be tightened or removed use a 1 4 in Allen wrench HOW TO REPLACE REFRIGERATOR DOOR HANDLE NOTE Handle appearance may vary from illustrations on this page Replacing Refrigerator Door Handle Place the handle on the door by fitting the handle footprints over the mounting fasteners and tightening the set screws with a 3 32 in Allen wrench NOTE If the handle mounting fasteners need to be tightened or removed use a 1 4 in Allen wrench Mounting Fasteners Set Screw Allen Wrench Mounting Fasteners 11 NOTE Removing the doors is always recommended when it is necessary to move the refrigerator through a narrow opening If it is necessary to remove the handles follow the directions below HOW TO REMOVE FREEZER DOOR HANDLE NOTE Handle appearance may vary f
57. stalled in accordance with the Attention Installer Instructions that were taped to the front of the refrigerator After your refrigerator is in operation do not touch the cold surfaces in the freezer compartment when hands are damp or wet Skin may adhere to the extremely cold surfaces DO NOT touch the automatic ice making mechanism while the refrigerator is plugged in DO NOT refreeze frozen foods which have thawed completely The United States Department of Agriculture in Home and Garden Bulletin No 69 says You may safely refreeze frozen foods that have thawed if they still contain ice crystals or if they are still cold below 4 C Thawed ground meats poultry or fish that have any off odor or off color should not be refrozen and should not be eaten Thawed ice cream should be discarded If the odor or color of any food is poor or questionable dispose of it The food may be dangerous to eat Even partial thawing and refreezing reduces the eating quality of foods particularly fruits vegetables and prepared foods The eating quality of red meats is affected less than that of many other foods Use refrozen foods as soon as possible to save as much of their quality as you can SAVE THESE INSTRUCTIONS A DANGER RISK OF CHILD ENTRAPMENT Junked or abandoned refrigerators are dangerous even if they are sitting for only a few days If you are getting rid of your old refrigerator please follow the instructi
58. t pressure on the doors to get them to close below completely NOTE Tools Required 16 18mm wrench or flat blade screwdriver Deor Alignment Both the left and right refrigerator doors have an adjustable nut located on the bottom hinge to raise and lower them to align properly 1 Remove the base grille refer to page 10 2 Turn the leveling leg to the left to raise that side of the refrigerator or to the right to lower it It may take If the space between your doors is uneven follow the several turns of the leveling leg to adjust the tilt of the instructions below to align the doors evenly refrigerator Use the wrench included with the Use amp Care Guide to turn the nut in the door hinge to adjust the height To the right to raise or to the left to lower the height DI NOTE Having someone push backward against the top of the refrigerator takes some weight off of the leveling legs This makes it easier to adjust the legs 17 USING YOUR REFRIGERATOR SETTING THE CONTROLS Temperature CHANGE FILTER Door Reset a CONTROL LOCK HOLD ASEC HOLD ISEC e The Refrigerator Temp Control ranges from 33 F to 46 F 0 C to 8 C Press the Refrigerator Temp button to cycle through the available temperature settings one increment at a time The Freezer Temp Control range is from 6 F to 8 F 21 C to 13 C Press the Freezer Temp button to cycle through the available temperature se
59. the crisper for best storage of fruit Ay CAUTION The glass shelf over the crisper is not firmly secured Be careful when tilting a lt Humidity Control 1 To remove pull the drawer out to full extension 2 Lift the front of the crisper up then pull it straight out 3 To install slightly tilt up the front insert the drawer into the frame and push it back into place High eseese fesses Low REMOVING THE HUMIDITY CONTROLLED CRISPER 26 To remove the glass 1 Lift up the glass under the crisper cover 2 Pull the glass up and out MODULAR DOOR BIN The door bins are removable for easy cleaning and adjustment 1 To remove the bin simply lift the bin up and pull straight out 2 To replace the bin slide it in above the desired support and push down until it stops NOTE Some bins may vary in appearance and will only fit in one location To prevent damage never use excessive force when removing or reinstalling the door bins CAUTION Crispers Door Bins and interior shelves are not dishwasher safe FREEZER SECTION PULLOUT DRAWER DURABASE 1 To remove pull the drawer out to full extension Lift the 1 To remove the Durabase push it to the back as much front of the drawer up then pull it straight out as possible Tilt up the front of the Durabase and pull straight
60. time which will prevent them from properly dispensing Check the ice bin for ice cubes clumping sticking together If they are break up the ice cubes to allow for proper operation Eliminate the frost or ice fragments by removing the ice bin and clearing the chute with a plastic utensil Dispensing cubed ice can also help prevent frost or ice fragment buildup Press and hold the Lock button for three seconds to unlock the control panel and dispenser lt may take up to 24 hours for each compartment to reach the desired temperature and for the icemaker to begin making ice Make sure that the shutoff arm sensor is not obstructed Once the ice supply in the bin has been completely exhausted it my take up to 90 minutes before additional ice is available and approximately 24 hours to completely refill the bin H ice amp WATER Problem Possible Causes lcemaker is not making ice Not dispensing water Refrigerator was recently installed or icemaker recently connected Icemaker not turned on The ice detecting sensor is obstructed The refrigerator is not connected to a water supply or the supply shutoff valve is not turned on Icemaker shutoff arm or sensor obstructed Reverse osmosis water filtration system is connected to your cold water supply New installation or water line recently connected The dispenser panel is locked The dispenser is not s
61. ttings one increment at a time NOTE When changing control settings wait 24 hours before making additional adjustments The controls are set correctly when milk or juice is as cold as you would like and when ice cream is firm If the temperature in either compartment is too cold or too warm change the setting one increment at a time Wait 24 hours for the change to stabilize before adjusting again Ultra Ice When you press the Ultra Ice button the Ultra Ice graphic will illuminate in the display and will continue for 24 hours The function will automatically shut off after 24 hours You can stop this function manually by touching the button one more time This function increases both ice making and freezing capabilities Dispenser e Press the Ice amp Water button to select either Water Cubed Ice or Crushed Ice The selected option will illuminate Some dripping may occur after dispensing Hold your cup beneath the dispenser for a few seconds after dispensing to catch all of the drops NOTE The dispenser will not work if any door is left open or if the control lock is engaged CAUTION The control display is operated by touch Excessive moisture on the display may cause a malfunction Please keep the display clean and dry 18 Filter Reset When the water filter indicator turns on you have to change the water filter After changing the water filter press and hold the Filter R
62. ve any burrs resulting from drilling the hole in the pipe Be careful not to allow water to Route the tubing through a hole drilled in the wall or floor behind the refrigerator or adjacent base cabinet as close to the wall as possible drain into the drill Failure to NOTE Be sure there is sufficient extra tubing about drill a 1 4 in hole may result 8 feet coiled into 3 turns of about 10 in diameter to in reduced ice production or allow the refrigerator to move out from the wall after smaller cubes installation 7 CONNECT THE TUBING TO THE VALVE Place the compression nut and ferrule sleeve for copper tubing onto the end of the tubing and connect it to the shutoff valve Make sure the tubing is fully inserted into the valve Tighten the compression nut FASTEN THE SHUTOFF VALVE securely Fasten the shutoff valve to the cold water pipe with the pipe clamp NOTE The hookup line cannot be white plastic tubing Licensed plumbers must use only copper tubing NDA tubing 49595 or 49599 or Cross Link Polyethylene PEX tubing Saddle Type Shutoff Valve NN s ompression Nut Pipe Clamp 734 Outlet Valve Ferrule sleeve Vertical Cold Water Pipe Saddle Type auto SNe NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and their use is not permitted in NOTE Commonwealth of Massachusetts Plumbing Massachusetts Consult with your licensed plumber Codes
63. y relocated If the refrigerator was stored for a long period of time or moved on its side it is necessary for the refrigerator to stand upright for 24 hours before connecting it to power Cooling System runs Refrigerator is replacing an older Modern refrigerators require more operating time but too much model use less energy due to more efficient technology Refrigerator was recently plugged in The refrigerator will take up to 24 hours to cool or power restored completely Door opened often or a large amount Adding food and opening the door warms the of food hot food was added refrigerator requiring the compressor to run longer in order to cool the refrigerator back down In order to conserve energy try to get everything you need out of the refrigerator at once keep food organized so it is easy to find and close the door as soon as the food is removed Refer to the Food Storage Guide Doors are not closed completely Firmly push the doors shut If they will not shut all the way see the Doors will not close completely or pop open section in Parts amp Features Troubleshooting Refrigerator is installed in a hot The compressor will run longer under warm conditions location At normal room temperatures 70 F expect your compressor to run about 40 to 80 of the time Under warmer conditions expect it to run even more often The refrigerator should not be operated above 10 F Condenser back cover is

Kenmore 795.7202 Refrigerator User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents