Kenmore 116.36932 Vacuum Cleaner User Manual
Contents
1. Remove the telescopic wand from the wand holder age position in the wand Turn the lock ing ring to the UNLOCK position 1 Hose Collar Wand Holder Extend the wand to its full length Turn the locking ring to the LOCK position Attach the wand onto the open end of the hose Suction Control Slide EN s ny Pi Wand gt sE Locking Ring fa w Upper Wand Align the tabs on the wand with the J slots in the hose Push the wand into the hose and twist to the right to lock i Suction Stide Control To achieve maximum reach with the attachments add the crevice tool to the end of the wand by inserting and twisting slightly The combination brush can be attached direcily to the wand Brush gt Combination Brush 2 Brush Holder Use the brush holder without the brush for greater suction on furniture cushions or stairs Use brush holder with brush for cleaning loose surfaces such as drapes Altach floor brush directly to extension wand Hase Use the floor brush for cleaning of floors or stairs TO OPERATE SUCTION CONTROL SLIDE Telescopic Wand When using attachments for cleaning draperies small rugs with low pile and other delicate items twist the suction control slide to the open position This slide is located on the telescopic wand close to the hose This will reduce suction for ease of cleaning Suction Note Return Sentral suction contr2. sor is amber and red indicating that inteliCLEAN power is at MAXIUM The vacuum cleaner operates at its highest energy consumption and noise levels inteliCLEAN Dirt Sensor indicator Lights Green Zew ee Motor Fan Speed T T Dirt Sensor Lights Amber Motor Fan Speed T Dirt Sensor Lights Red Dirt Sensor Lights Amber Motor Fan Speed Your Kenmore Vacuum Cleaner features a 2 Use the GENTLE setting low speed two 2 speed direct drive agitator for ONLY for berber or delicate pile car cleaning a variety of floor surfaces Please peting The agitator may slow down or review the table below before using your stop on thick carpeting area rugs or vacuum cleaner throw rugs If agitator stops and does not restart see AGITATOR MOTOR 4 Do not use the CARPET setting high OVERLOAD PROTECTOR speed for cleaning berber style car pet The high agitator speed could 3 The FLOOR setting may be used for damage the carpet or cause excessive all indoor bare floors including wood carpet wear tile linoleum slate etc Berber Commercial or Delicate or Low Pile Carpet 2 To select a pile height setting Turn off vacuum cleaner Select a pile height setting by tilting the vacuum cleaner back until front wheels are lifted slightly off the floor Slide the adjustment lever to the correct setting There are four 4 pile height settings on the vacuum cleaner Use the LOW setting for
3. A Hose Storage Position Extension Hose Hose Collar Re insert the hose into the opening on the body from which it was removed Press firmly to assure connection Rotate hose release lever clockwise to the locked position lf the dust bin and filter areas and the hose areas are free of clogs disconnect the noz zle hose from the wand holder and check the nozzle for clogging A WARNING Personal Injury Hazard DO NOT place hands or feet underneath the vacuum cleaner at any time Clean the agitator according to the instruc tions in the AGITATOR CLEANING section Return the vacuum cleaner to the upright position before plugging into an electrical outlet Review this table to find do it yourself solutions for minor performance problems Any service needed other than maintenance described in this Owner s Manual should be performed by a Sears or other qualified service agent Disconnect electrical supply before performing maintenance to the vacuum cleaner Failure to do so could result in electrical shock or personal injury Vacuum cleaner won t run Poor job of dirt pick up Vacuum Cleaner picks up moveable rugs or pushes too hard Light won t work Agitator does not turn Airflow restricted with attachment use Sound changes Difficulty adjusting plle height setting Dirt Sensor will not work 4 Dirty optic cells 1 1 Unplugged at walt outlet 2 Tripped circuit breaker
4. or pull cord around sharp edges or corners Do not run vacuum cleaner over cord Keep cord away from heated surfaces Do not unpiug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or vacuum cleaner with wel hands Do not put any objects into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Turn off all controls before unplugging Use extra care when cleaning on stars Do not put on chairs tables etc Keep on floor Do not use vacuum cleaner to pick up flammable or combustible liquids gasoline cleaning fluid perfumes efc or use in areas where they may be present The fumes from these substances can create a fire hazard or explosion De not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use vacuum cleaner without dust bin and or filters mn place Always clean the dust bin after vacuuming carpet cleaners or freshener powders and fine dust These products clog the filters reduce airflow and can cause damage to the vacuum cleaner Failure to clean the dust bin could cause permanent damage to the vacuum cleaner Do not use the vacuum cleaner ta pick up sharp hard objects smali toys pins paper clips etc They may damage the vacuum cleaner or dust bin Unplug
5. plug in any way 3 Plug the polarized power cord into a 120 Volt outlet located near the floor 4 To replace cord turn upper cord hook to the up position then wrap cord WARNING Personal injury and Product Damage Hazard DO NOT place hands or feet under the vacuum cleaner at any time DO NOT use outlets above coun ters Damage from cord to items in surrounding area could occur Release the handle by pressing dawn on the handle release pedal with your foot and pulling back and down on the handle with your hand Note The agitator does nat rotate when the vacuum cleaner ts in the upright position inteliCLEAN Turns ON the vacuum cleaner in inteliCLEAN mode SUCTION TOOLS Changes the suction level of the vacuum cleaner motor If the vacuum cleaner is OFF and locked in the upright position pressing the SUCTION button turns ON only the vacuum cleaner motor to HIGH for cleaning of most car pets rugs and fabrics The agitator starts in HIGH speed when the vacuum cleaner is lowered into the operating position Pressing the SUCTION button cycles the vacuum cleaner motor through suction levels H N L HIGH MEDIUM LOW GENTLE FLOOR Turns ON the vacuum cleaner motor to HIGH suction level and the agitator motor to LOW speed level for gentle cleaning of most delicate carpets and rugs Pressing the GENTLE FLOOR button a second time turns OFF the agita ter motor for cleaning bare
6. Electrical Shock Hazard until the assembly is complete Failure to do so could result in electrical shock or injury Before assembling the vacuum cleaner check the PACKING LIST on the cover of the separate REPAIR PARTS LIST Use this list to verify that you have received all the components of your new Kenmore vacuum cleaner HANDLE ASSEMBLY Remove the combination brush from the handle to expose the handle mount ing hole Remove the handie screw from the body of the vacuum cleaner Position the handle assembly as shown in the illustration below When installing the handle firmly press the handle onto the body Secure with handle screw provided Begin to tighten the screw with your fin gers It may be necessary to adjust the handle slightly Using a screwdriver tighten handle screw Reinstall combination brush Electrical Connection Handle Assembly Handle Screw given WARNING statements alert you to such dangers as fire electric shock burns and personal injury CAUTION statements alert you to such dangers as personal Do not plug into the electrical supply A CAUTION Do not overtighten Overtightening could strip the screw holes Do not operate the vacuum cleaner without the screw in place CORD ASSEMBLY Make sure the quick release upper cord hook is in the upright position Remove the wire tie from the power cord Make sure the power cord is endidura p
7. before connecting Handi mate Jr You are responsible for making sure that your vacuum cleaner is not used by anyone unable to operate it properly SAVE THESE INSTRUCTIONS Proper assembly and safe use of your vacuum cleaner are your responsibilities Your vac uum Cleaner ts intended for Household use Read this Owners Manual carefully for important use and safety information This guide contains safety statements under warn ing and caution symbols It is important to know your vacuum cleaner s parts and features to assure its proper and safe use Review these before using your vacuum cleaner Part No in Canada Headlight Bulb 20 5248 Exhaust Filter 20 86889 20 40324 Primary Filter DCF 2 20 82912 20 40335 Control Handi Mate Jr manate farei ANES Quick Release Upper Cord Hook Dust Bin Cleaning Lever Power Cord Telescopic Wand Combination Brush Crevice Tool Agitator Carrying Reset Handle Button Upper Hose Hook Extension Hose Pile Height Adjustment Headlight Furniture Guard Handle Release Nozzle Pedal f i Extension Hose N 4 Release Lever Motor Protector Behind Hose Dirt Sensor Dust Bin Release Handle Dust Bin Za Exhaust Filter Cover Filter inside Please pay special attention to these hazard alert boxes and follow any instructions injury and or property damage A WARNING
8. floors In order to get MEDIUM and LOW suction levels for cleaning press the SUCTION button to cycle the vacuum cleaner motor through MEDIUM LOW and HIGH suction levels respectively CARPET Turns ON the vacuum cleaner motor to HIGH suction level and the agita tor motor to HIGH speed level for cleaning of most carpets and rugs In order to get MEDIUM and LOW suction levels for cleaning press the SUCTION button to cycle the vacuum cleaner motor through MEDIUM LOW and HIGH suction levels respectively OFF Turns OFF vacuum cleaner HIGH HIGHIMEDIUM LOW Variable Power Your Kenmore vacuum cleaner is equipped with the latest technology in floor care The Kenmore inteliGLEAN automatically chooses the right cleaning power for any cleaning need Medium power for everyday pickup High power for normal dirt and Maximum power for deep cleaning high traffic areas When inteliCLEAN mode is activated the inteliCLEAN indicator is green To turn OFF or de activate inteliCLEAN press the inteliCLEAN button or TOOLS button When there is little or no dirt present the dirt sensor is green indicating that inteliCLEAN power is at MEDIUM At MEDIUM power the vacuum cleaner operates at low energy con sumption and noise levels With normal dirt concentration the dirt sen sor is amber indicating that inteliCLEAN power is at HIGH Energy consumption and noise levels increase With heavy dirt concentration the dirt sen
9. follow all safety precautions when performing maintenance to the vacuum cleaner WARNING Electrical Shock And Personal injury Hazard Disconnect electrical supply before servicing or cleaning the vacuum cleaner Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting Gather the cord and wrap it loosely around the upper and lower cord hooks Lock power cord plug onto the power cord Store the vacuum cleaner in a dry indoor area on the floor with the handie locked in the upright posi tion WARNING Electrical Shock And Personal injury Hazard Wrapping the cord too tightly puts stress on the cord and can cause cord damage A damaged cord ts an electrical shock hazard and could cause personal injury or damage Unplug cord from wall outlet DO NOT drip water on vacuum cleaner Clean exterior using a clean soft cioth that has been dipped in a solution of mild liquid detergent and water then wrung dry Wipe dry after cleaning To reduce static electricity and dust build up wipe outer surface of vacuum cleaner and attachments Wash attachments in warm soapy water rinse and air dry Do not clean in dish washer 16 CAUTION Do not use attachments if they are wet Attachments used in dirty areas such as under a refrigerator should not be used on other surfaces until they are washed They could leave marks WARNING Al
10. Owner s Manual Manual Del Propietario Vacuum Cleaner Aspiradora Model Modelo 116 36932 A 116 36933 t IMPORTANT Before returning this product For replacement parts please contact Sears Parts and Repair Center 1 800 488 1222 a Anytime day or night i U S A only For any other issue please contact Vacuum Cleaner Help Line 1 877 531 7321 7 30am 4 00pm EST M F U S A and Canada gQ CAUTION CUIDADO Read and follow all Lea y sigue todas las safety and operating instrucciones de operaci n instructions before first y seguridad antes del uso use of this product de este producto Sears Roebuck and Co Hoffman Estates IL 60179 U S A www sears com Printed in Mexico Part No C IZCSRIJU KC 1ZCSRZ U Impreso en Mexico Before Using Your New Vacuuming Tips 0 000000 ee 13 Vacuum Cleaner oe Perforrnance Safety Features 14 15 Kenmore Vacuum Gleaner Warranty 3 important Safety Instructions 4 Vacuum Cleaner Care wee rere Parts and Features OR ag Vacuum Cleaner Storage ae 16 Assembly Instructions 6 7 Cleaning Exterior and Attachments _ 16 Dust Bin Cleaning 17 Operating instructions 7 Primary Filter Removal Cord Release 7 and Cleaning 18 19 Releasing the Handle 8 Exhaust Filter Replacement _ aes Touch Control 8 Light Bulb Replacement 20 inteliCLEAN 2 0 0 0 9 Agitator Cleaning ARETOEN A Gentle
11. Place vacuum cleaner in the locked upright position tilt the vacuum clean er back slightly and adjust pile height Clean optic cells Your Home For repair in your home of all major brand appliances lawn and garden equipment or heating and cooling systems no matter who made it no matter who sold it For the replacement parts accessories and owner s manuals that you need to do it yourself For Sears professional installation of home appliances and items like garage door openers and water heaters 1 800 4 MY HOME Anytime day or night 1 800 469 4663 U S A and Canada www sears com WWW sears ca Our Home For repair of carry in products like vacuums lawn equipmeni and electronics call or go on line for the nearest Sears Parts and Repair Center 1 800 488 1222 Anytime day or night U S A only www sears com To purchase a protection agreement U S A or maintenance agreement Canada on a product serviced by Sears 1 800 827 6655 U S A 1 800 361 6665 Canada Para pedir servicio de reparaci n Au Canada pour service en fran ais a domicilio y para ordenar piezas 1 800 LE FOYER 1 888 SU HOGAR 1 800 533 6937 1 888 784 6427 www sears ca Sears Roebuck and Co Registered Trademark M Trademark Service Mark of Sears Brand LLC Marca Registrada Marca de Fabrica Marca de Servicio de Sears Bra Roebuck ands LLC MC Marque de
12. Sweep Function 10 Clog Removal 24 Pile Height Selection and Setting 10 Troubleshooting 292 Attachments 2020 00 00 000 1 12 Requesting Assistance Attachment Use Table 13 Or Service back page Please read this guide It will help you assemble and operate your new Kenmore vacuum cleaner in the safest and most effective way For more information about vacuum cleaner care and operation call your nearest Sears store You will need the complete model and serial numbers when requesting information Your vacu um cleaners mode and serial numbers are located on the Model and Serial Number Plate Use the space below to record the model number and serial number of your new Kenmore vacuum cleaner Model No Serial No Date of Purchase Keep this book and your sales check receipt in a safe place for future reference One Year Limited Warranty When assembled operated and maintained according to all instructions supplied with the product if this vacuum cleaner fails due to a defect in material or workmanship within one year from the date of purchase return it to any Sears store Sears Parts amp Repair Center or other Kenmore outlet for free repair If this vacuum cleaner is used for other than private family purposes this warranty applies for only 90 days from the date of purchase This warranty covers only defects in material and workmanship Sears will NOT pay for 4 Expendable items t
13. blown fuse at household service panel 3 Thermal protector tripped 4 Defective wail outlet wn Handie screw not tight 1 Full or clogged dust bin Wrong pile height setting a Worn agitator w N 4 Clogged nozzle Clogged hose 6 Hole in hose 7 Hose not inserted fully Motor protection system activated change of sound 9 Dirty filters Wrong pile height setting 4 Burned out light bulb 1 Handie in full upright position 2 Agitator Overload tripped 3 Thermal protector tripped 4 Attachment use restricts air flow 2 New carpet fuzz clogged air path 1 Vacuum cleaner not in proper upright position 22 3 is OP on mun 2 t Plug In firmly select the desired set ting on the touch control Reset circuit breaker or replace fuse Allow vacuum cleaner to cool then reset thermal protector Check with a good appiiance lamp have properly serviced Tighten screw Empty dust bin Adjust setting Take to your nearest Sears Service Center Check for clags Check for clogs Take to your nearest Sears Service Center insert hose fully Check for clogs Change filters Adjust setting Change light bulb Move handle from upright position Reset Agitator Overload Allow vacuum cleaner to cool then reset thermal protector Check attachments for fuzz lint pet hair or other debris Check for clogs and clean hose
14. commerce 4 Marque d pos e de Sears Brands LLC
15. er Note See PARTS AND FEATURES for the filter number TO REPLACE PRIMARY FILTER To replace filter insert it over cleaning cams as far as it will go Make sure rubber seal at top of filter is flush against filter sup porter then turn filter clockwise to secure into place Filter will click and snap when it is secured into place Note Under normal use and care your fil ter can be expected to last up to 5 years R Rubber Cleaning Seal Cams Filter Filter Filter Supporter Dust Bin Lid Re assemble dust bin lid to dust bin see To REPLACE DUST BIN LID TO REPLACE DUST BIN LID Replace dust bin lid assembly by placing back on dust bin with marks on the lid aligned as shown under Open For Emptying on the back of the dust bin Turn This Direction To Close For Use Open For Emptying oni Closed For Use Rotate clockwise while pressing downward so marks align as shown above Closed For Use Insert dust bin into vacuum cleaner Lower the dust bin handle to lock dust bin in place Dust Bin Handle A noticeable click should be heard The HEPA exhaust filter must be replaced when dirty It should be replaced regularly depending on use conditions The filter CANNOT be washed as it will lose its dust trapping ability Note See PARTS AND FEATURES for the exhaust filter number Remove exhaust filter cover by pressing the release tab on the cover and rotating out
16. from vacuum cleaner Remove the filter cartridge from cover Place new filter cartridge into cover making sure that airflow arrow on side of cartridge ints i po into cover 19 Place the foam seal of the filter should be placed against the vacuum cleaner body Seal Against Exhaust Vacuum Cleaner Body D qa BAIRFE OWE x Filter Replace the exhaust filter cover by placing bottom tabs in slots and rotating in until cover snaps into place WARNING Electrical Shock Or Personal Injury Hazard Disconnect electrical supply before performing maintenance to the vacuum cleaner Failure to do so could result in electrical shock or personal injury from the vacuum cleaner suddenly starting TO REMOVE LIGHT BULB 1 Disconnect power cord from electrical outlet 2 Press han dle release pedal and lay vacuum clear Flat Screwdriver er back 3 Pry light lens out at slots as shown on both sides bia Rotate Jens up and lift off A CAUTION Bo not use a bulb rated over SW 13V During extended use heat from the bulb could overheat surrounding plas tic parts 20 4 Remove the light bulb by pulling straight out 5 Carefully insert new light bulb fully into slot Note See PARTS AND FEATURES fer bulb number CAUTION Do not plug in or turn on until the vacu um cleaner is completely reassembled amp To replace ligh
17. hat can wear out from normal use including but not limited to filters belts light bulbs and bags 2 Aservice technician to instruct the user in correct product assembly operation or maintenance 3 A service technician to clean or maintain this product 4 Damage to or failure of this product if it is not assembled operated or maintained according to all instructions supplied with the product 5 Damage to or failure of this product resulting from accident abuse misuse or use for other than its intended purpose 6 Damage to or failure of this product caused by the use of detergents cleaners chernicals or utensils other than those recommended in ail instructions supplied with the product 7 Damage to or failure of parts or systems resulting from unauthorized modifications made to this product Disclaimer of implied warranties limitation of remedies Customer s sole and exclusive remedy under this limited warranty shall be product repair as provided herein Implied warranties including warranties of merchantability or fitness for a particular purpose are limited to one year or the shortest period allowed by law Sears shall not be liable for incidental or consequential damages Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages or limitations on the duration of implied warranties of merchantability or fitness so these exclusions or limitations may not apply to you This wa
18. laced into the lock e fijaci n ing notch on the body as shown This helps keep the power cord out from under the vacuum cleaner agitator Cord n Wrap the power cord around the quick release cord hook and the carrying handle Lock the power cord plug onto the power cord HANDI MATE JR TELESCOPIC WAND PLACEMENT Place the telescopic wand in the wand holder Place the crevice tool in the top of the telescopic wand For operation of Handi Mate Jr see separate Owner s Manual TO INSERT HANDI MATE JR Place Handi Mate Jr into the storage compartment Rotate the Handi Mate Jr back until it snaps into place TO REMOVE HANDI MATE JR Rotate Handi Mate Jr out of the storage compartment OPERATING INSTRUCTIONS Turn the quick 2 Detach the Hendidura release upper power cord plug de fijaci n cord hook to from the power cord either side and and pull the cord off O down to release the quick release the power cord upper cord hook CPraoi Be sure the power cord is still locked into the locking notch of the upper cord hook WARNING To reduce the risk of electric shock this vacuum cleaner has a polar ized plug one blade is wider than the other The plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified technician to install the proper outlet Do not change the
19. most low pile carpets and bare floor cleaning with agitator OFF and the HIGH setting for high pile carpets like shag carpet scatter rugs etc Use the other settings as needed for carpet heights in between A CAUTION Do not allow vacuum cleaner to remain in one spot for any length of time when the agitator is turning Damage to carpet may occur 10 Handi Mate Jr Combination Brush Carrying Handle Extension Hose Extension Hose Release Lever TO USE ATTACHMENTS Remove the lower end of the extension hose from the wand holder by grasping the hose collar twisting and pulling straight up Rotate the extension hose release lever down if maximum reach is needed Note The motor protector may open when using attachments or when cleaning new carpet due to reduced airflow caused by the attachments themselves or caused by new carpet lint filling the dust bin quickly See the TROUBLESHOOTING section AX WARNING Electrical Shock And Personal Injury Hazard Disconnect electrical supply before ser vicing or cleaning the vacuum cleaner Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting 11 T S 1 Remove the crevice tool frorn its stor ELESCOPIC WAND WITH UCTION CONTROL SLIDE Remove the lower end of the extension hose from the wand holder by grasping the hose collar twisting and pulling straight up
20. n the front of the vacuum cleaner above the dust bin Dirt Sensor When little or no dirt is present the dirt sensor is green With medium dirt concentration the dirt sensor is amber With heavy concentration the dirt sendor is red and amber A WARNING Electrical Shock And Personal Injury Hazard Disconnect electrical supply before per forming maintenance to the vacuum cleaner Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting 15 OPERATION As you vacuum the amber and red indicator lights will come on and stay on as long as the sensor detects a high concentration of particles passing through the vacuum cleaner TO CLEAN DIRT SENSOR OPTICS The dirt sensor optics consist of two optic cells located inside the dust bin port Occasionally it may become necessary to clean the two optic cells to assure maximum performance it is recommended the optic cells be cleaned When the red light stays on continuously When dirt or dust adheres to the optic cells Whenever the dust bin is emptied Dirt Sensor Optic Celis ene To clean the sensor wipe the optic cells with a soft dry cloth Never use cleaners or liquids as they can help speed the recoating of the optic cells and make it necessary to clean them much sooner than normal The dirt sensor area can be reached by removing the dust bin VACUUM CLEANER CARE Always
21. n using the attachments keep the extension hose release lever in the locked position when possible This helps to keep the vacuum cleaner from tipping over when stretching the hose if additional hose is needed then unlock the release lever and pull out additional hose Use caution not to tip over vacuum cleaner A WARNING Personal Injury Hazard Use care if vacuum cleaner is placed on stairs ff it falis personal injury or prop erty damage could result For best cleaning results keep the airflow passage clear Unplug the vacuum cleaner from the outlet before checking 13 MOTOR PROTECTION SYSTEM Motor Protector This vacuum cleaner has a motor protector by pass valve which automatically opens to provide cooling air to the vacuum cleaner motor when a clog prevents the normal flow of air to the motor If the by pass valve opens to prevent motor overheating and possible damage to the vacuum cleaner you will notice a change of sound as air rushes through the valve opening To correct problem empty the dust bin If using attachments adjust to allow for greater air flow NOTE The motor protector may open when using attachments or when cleaning new carpet due to reduced airflow caused by the attachments themselves or by new carpet lint filling the dust bin quickly To correct problem empty the dust bin If using attachments adjust to allow for greater air flow Motor Protector Behind Hose No
22. ol slide to the closed position for normal cleaning CAUTION When using attachments be careful not to overextend the stretch hose when reaching Trying to reach beyond the hose stretch capability could cause the vacuum cleaner to tip over TO STORE ATTACHMENTS Remove the combination brush Snap into appropriate storage location Remove crevice too from the wand by twist ing Lay aside Remove the telescopic wand from the hose Twist the wand to the left and pull from the hose end Unlock the wand by turning the wand locking ring to the UNLOCK position Slide the lower wand into the upper wand Turn the wand locking ring to the LOCK posi tion Place the crevice tool down inte the com pressed wand Place the telescopic wand in the wand holder AX CAUTION DO NOT pull the vacuum cleaner around the room by the hose Property damage or personal injury could result Between Cushlons Always clean attachments before using on fabrics Applicable Use the brush holder with out the brush for greater suction on furniture cushions ar stairs Use brush holder with brush for cleaning loose surfaces such as drapes Carpet edges Guide either side or the front of the noz zle along a baseboard Stairs Set handle in full upright position Agitator stops rotating Use the crevice tool com bination brush or Handi Mate Jr Vacuum cleaner Tipping Whe
23. raised Lower the dust s4 bin handle to lock dust bin in Al iplace A noticeable click should be heard A WARNING Electrical Shock And Personal Injury Hazard Unplug power cord from electrical out let Do not operate the vacuum cleaner without the primary or exhaust filters Be sure the filters are properly installed to prevent motor failure and or electrical shock PRIMARY FILTER Check primary filter frequently and clean when dirty TO REMOVE PRIMARY FILTER Remove the dust bin assembly as outlined in the DUST BIN CLEANING section Make sure dust bin is free of debris before removing lid and filter Rotate dust bin lid assembly counterclockwise as indicated on the lid and lift off Turn This Direction To Open For Emptying Closed For Use For Emptying While holding dust bin lid over a trash con tainer grasp primary filter rotate counter clockwise and lift off Clean primary filter by gently tapping over a trash container Tap on several sides to ensure best cleaning 18 Remove primary filter by turning it counterclock wise and pulling out See arrows on bottom of fil ter Rinse with water only as needed do not use any deter gent or soap Allow the filter to dry for 24 hours before putting it back into the vacuum cleaner When cleaning the filter no longer restores vacuum cleaner s suction to full power you need to replace the filt
24. rranty applies only while this vacuum cleaner is used in the United States and Canada This warranty gives you specific legal rights and you may also have other rights which vary from state to state Sears Roebuck and Co Hoffman Estates IL 60179 Sears Canada Inc Toronto Ontario Canada M5B 2B8 IMPORTANT SAFETY INSTRUCTIONS AWARNING Your safety is important to us To reduce the risk of fire electrical shock injury to persons or damage when using your vacuum cleaner follow basic safety precautions including the following Read all instructions in this manual before assembling or using your vacuum cleaner Use your vacuum cleaner only as described in this manual Use only with Sears recommended attachments Disconnect electrical supply before servic ing or cleaning out the brush area Failure to do so could result in electrical shock or the brush suddenly starling Do not leave vacuum cleaner when plugged in Unplug from outlet when not in use and before performing maintenance To reduce the risk of electrical shack Do not use outdoors or on wet surlaces Do not allow to be used as a tay Close attention Is necessary when used by ar near children Do net use with a damaged cord or plug If vacuum cleaner is not working as it should has been dropped damaged left outdoors or dropped in water return it fo a Sears Service Center Do not pull or carry by card use cord as a handle close a door on card
25. t lens place tab at front of lens into slot Rotate lens down and firmly snap into place To maintain efficient cleaning the agitator must be kept free of carpet fiber string or hair build up After every 7 to 10 uses unplug and turn vacuum cleaner over and check agitator for fiber and hair build up Use scissors to remove any build up entan gled around the agitator Always follow all safety precautions when per forming maintenance to the vacuum cleaner AE BI OU Ure t NODO 2 FG Di LO U Ya Vee AO 4 E WG EtG 213 pany VG Yang Uz we V ve YaB 4 2 A KA t4 Oti PRR AT a yae Yan 6 Yn G et if the vacuum cleaner does not seem to have adequate suction first check if the dust bin is full or if a filter is clogged See DUST BIN CLEANING and FILTER REPLACEMENT If the dust bin and filter areas are free of clogs check the extension hose Rotate the extension hose release lever counterclock wise to release extension hose PY NU e Extension j AO Hose ON j i Wand Hose RI Holder Collar i SA ISS gt Extension Hose Release Lever Nozzle Hose Remove the lower end of the extension hose from the wand holder by grasping the hose collar twisting and pulling straight up Plug in the vacuum cleaner and turn it on Stretch the extension hose to maximum length and then allow the hose to return to its natural ee N de Original
26. te Do not block motor protector Therma Protector This vacuum cleaner has a thermal protector which automatically trips to protect both the vacuum cleaner and the agitator motor from overheating If a clog prevents the normal flow of air to the motor the thermal protector turns the motor off automatically This allows the motor to cool in order to prevent possible damage to the vacuum cleaner To correct problem Turn the vacuum cleaner off and unplug the power cord from the outlet to allow the vacuum cleaner to cool and the thermal protector to reset Check for and remove clogs if necessary See CLOG REMOVAL section Also check and replace any clogged filters Wait approximately thirty 30 minutes before restarting vacuum cleaner AGITATOR MOTOR OVERLOAD PROTECTOR The agitator motor has built in protection against motor damage should the agitator jam If the agitator slows down or stops the agitator overload protector shuts off the agitator motor The vacuum cleaner motor will continue to run To correct problem Turn off and unplug vacuum cleaner remove obstruction then press Agitator Motor reset button If the problem persists have the vacuum cleaner serviced by a Sears or other qualified technician Agitator Motor Reset Button DIRT SENSOR The electronic dirt sensor is a feature which will detect particles as they pass through the vacuum cleaner The dirt sensor indicators are located o
27. ways unplug power cord from elec trical outlet before performing any ser vice on vacuum cleaner TO REMOVE DUST BIN Lift dust bin handle located at the top of the dust bin and lift dust bin up and out of the vac uum cleaner l Pull the handle up Handle Remove any clogs that might be located in the suction port or filter port area TO EMPTY DUST BIN Before removing debris from dust bin it is a good idea to move the dust bin filter clear ing lever back and forth several times Moving the lever back and forth pii Bin loosens the dust Cleaning and debris that Lever has attached itself to the filter element inside the dust bin Rotate dust bin handle to the vertical posi tion 17 Hold dust bin Dust Bin over a trash Handle container Press the dust bin door release button Deor downward to Release release the door The door will swing open and the debris will fall into the Aosta trash container Emptying Door ee ee ie A Shake the dust bin to release any debris that might hang in the filter element Note See PRIMARY FILTER REMOVAL AND CLEANING section After the dust bin is empty of debris firmly close the door Make sure you hear a click sound to indicate that the door is fully latched Door Door Latch TO REPLACE DUST BIN Place dust bin back into vacuum cleaner by inserting the bot tom first and tilting back with the dust bin handle
Download Pdf Manuals
Related Search