Kenmore 116.36722 Vacuum Cleaner User Manual
Contents
1. from the vacuum cleaner NOTE When vacuum cleaner is turned on the hose will have a tendency to collapse due to suction of the vacuum cleaner If more reach is needed Crevice Tool ee J A Dusting Brush 2 Wand An extra wand without tabs is included This extra wand can be added to the wand with tabs for extra reach insert wand and twist a quarter of a turn to secure fit If the dusting brush combination brush is being used and more reach is needed the crevice too can be added to the wand then the dusting brush can be added to the crevice tool TO STORE ATTACHMENTS Return the hose to its position on the wand and the attachments to their holders ATTACHMENT 4 Crevice Too A Carpet edges Guide either side or the front of the nozzle along a baseboard The full width agitator brushes help remove dirt at carpet edges Stairs Put handle in full upright position Use the crevice tool or fabric brush Set the On Off switch to ON WARNING Personal injury Hazard Use care if vacuum cleaner is placed on stairs If it falls personal injury or property damage could result Between Cushions 10 For best cleaning results keep the airflow passage clear Occasionally check each of the areas indicated for clogs Unplug the vacuum cleaner from the outlet before checking e 2 Be MOTOR PROTECTION SYSTEM Thermal Protector This vacuum cleaner has a thermal2. position sw Handi Mate Jr O Stretch Hose Identify each of the attachments shown above CAUTION When using attachments be careful not to overextend the stretch hose when reaching Trying to reach beyond the hose stretch capability could cause the vacuum cleaner to tip over CAUTION Attachments used in dirty areas such as under refrigerator should not be used on other surfaces until they are washed They could leave marks WARNING Electrical Shock And Personal Injury Hazard Disconnect electrical supply before servicing or cleaning the vacuum cleaner Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting TO USE ATTACHMENTS Remove the lower end of the stretch hose from the vacuum cleaner by grasping the hose collar twisting and pulling straight out The attachments can now be added to the hose Note The motor protector may open when using attachments or when clean ing new carpet due to reduced airflow by the attachments themselves or by new carpet fuzz filling the dust bin quickly See the TROUBLESHOOTING section The attachments will fit on the hose or the wand in addition the dusting brush will also fit on the crevice tool The hose can be pulled off the wand by grasping the cuff and twisting while pulling up The attachments can be added to the hose if the item to be cleaned is not far
3. protector which automatically trips to protect the vacuum cleaner from overheating If a clog prevents the normal flow of air to the motor the thermal protector turns the motor off automaticaily to allow the motor to cool in order to prevent possible damage to the vacuum cleaner To correct problem If this occurs turn the vacuum cleaner off and unplug the power cord from the outlet to allow the vacuum cleaner to cool and the thermal protector to reset Check for and remove clogs if necessary Also check and clean replace any clogged filters Wait approximately thirty 30 minutes and plug the vacuum cleaner in and turn back on to see if the motor protector has reset The motor protector will not reset if the vacuum cleaner is not turned off even if the vacuum cleaner has cooled down 11 Motor Protector This vacuum cleaner has a motor protector by pass valve which automatically opens to provide cooling air to the motor when a clog prevents the normal flow of air to the motor If the by pass valve opens to prevent motor overheating and possible damage to the vacuum cleaner you will notice a change of sound as air rushes through the valve opening Motor Protector Note Do not block motor protector To correct problem See the TROUBLE SHOOTING chart Note The motor protector may open when using attachments or when cleaning new carpet due to reduced airflow by the attachments themselves or by new carpet fuz
4. HANG ING AND AGITATOR CLEANING Replace the agitator assembly with a new one Reassemble the belt agitator agitator cover and nozzle cover See To replace belt in BELT CHANGING AND AGITATOR CLEANING section Review this chart to find do it yourself solutions for minor performance problems Any service needed other than those described in this owner s manual should be performed by a Sears authorized service representative WARNING Electrical Shock Or Personal Injury Hazard Disconnect electrical supply before servicing or cleaning the vacuum cleaner Failure to do so could result in electrical shock or personal injury Vacuum cleaner Unplugged at wall outlet won t run Tripped circuit breaker blown fuse Reset circuit breaker or replace fuse at household service panel On off switch not turned on Push on off switch to on Thermal protector tripped Reset thermal protector Clean dust bin Adjust setting Replace agitator Check CLOG REMOVAL Check for clogs Replace hose Replace fix belt tnsert hose fully Check for clogs Clean change filters Poor job of dirt pick up Full or clogged dust bin Wrong pile height setting Worn agitator Clogged nozzle or dust bin port Clogged hose Hoie in hose Broken misplaced belt Hose not inserted fully Motor protection system activated Dirty filters OPN AWAY NS SEN Pn spa gt pry o Vacuum cleaner p
5. Owner s Manual Manual Del Propietario SATA Vacuum Cleaner Aspiradora Model Modelo 116 36722 CAUTION Read and follow all safety and operating instructions before first CC use of this product SA CUIDADO Lea y sigue todas las instrucciones de operaci n y seguridad antes del uso de este producto Sears Roebuck and Co Hoffman Estates IL 60179 U S A www sears com Impreso en China Part No C 1ZCUY2 U KC IZCUYZ U Printed in China Before Using Your New Vacuum Cleaner 2 Kenmore Vacuum Cleaner Warranty 3 Important Safety Instructions 4 Parts and Features 5 Assembly Instructions 6 7 Operating Instructions 7 How To Start oo oooooooo o o 7 Pile Height Selection and Setting 8 Releasing the Handle 8 ON OFF Switch o o ooooooo 8 Attachments ooo ooo cece eee 9 Attachment Use Chart 10 Vacuuming Tips Se Sabine eae 10 Performance Features a 11 Vacuum Cleaner Care 12 Cleaning Exterior and Attachments 12 Dust Bin Cleaning 13 Dust Bin Assembly 14 Dust Bin Filter Changing Cleaning 15 Primary Filter Replacement 15 Secondary Filter Cleaning 16 Filter Changing Cleaning 17 Belt Changing and Agitator Cleaning 18 20 Cl
6. TO REPLACE BELT NOTE See PARTS AND FEATURES for belt number Loop the new belt on the motor shaft Loop the end of the new belt on the agitator insert the agitator by placing the rounded portion of the end cap down into the slot in the nozzle base NOTE Care must be taken due to the belt tension during reassembly BELT ROUTING Press firmly checking to see that each end is completely inserted on Agitator Assembly Check to see that the belt is centered in the belt groove Turn the agitator with you fingers to see that it turns freely To re attach the base plate insert the tabs into the slots along the front edge of the base Place the vacuum cleaner in full upright position Lower the base plate to its original position As the base is lowered the inner areas will brush against the dust compartment wheels 20 Locking Tabs i fess Locking Tabs A gentle pull outward may assist in reassem bly Press the base plate down until the two lock ing tabs snap into place Slide the right latch to the right and the left latch to the left to secure Return the vacuum cleaner to the upright position before plugging into the electrical outlet Always follow all safety precautions when cleaning and servicing the vacuum cleaner AR WARNING Electrical Shock Or Personal Injury Hazard Disconnect electrical supply before servicing or cleaning the vacuum cleaner Failure to d
7. ate are facing upward 18 Locate the two latches and the two lock ing tabs which secure the base plate To remove the base plate press the two latches inward Push in on the locking tabs toward the center of the vacuum cleaner Rotate the base plate away from the noz zle housing The sides of the base plate need to be pulled slightly outward to clear the wheels The agitator and belt are now exposed Carefully remove any residue that may exist in the belt area If the belt is still attached to the motor shaft there will be tension on the agitator If the belt is not broken remove it from the motor shaft before lifting the agitator Carefully lift the one end of the agitator and then lift the other end Personal Injury Hazard Be careful when removing the agitator as the belt tension is high Fallure to do so could result in personal injury from the agitator releasing quickly and snapping away TO CLEAN AGITATOR NOTE In order to keep cleaning efficiency high and to prevent damage to your vacuum cleaner the agitator must be cleaned every time the belt is changed The agitator must also be cleaned accord ing to the following schedule Vacuum Cleaner Use Clean Agitator HEAVY every week used daily MODERATE every month used 2 3 times week LIGHT every 2 months used 1 time week Remove any dirt or debris in the belt path area or in the agitator area Agitator Assembly
8. bs on Filter filter screen with tabs on lid Screen x Alignment Grasp primary filter rotate counter Tabs clockwise and lift out Clean primary filter by gently tapping over a trash container The filter may be cleaned by tapping it on a firm surface Tap on several sides to ensure best cleaning Every 6 months rinse filter exterior with Alignment water under a faucet Once the filter is Tabs rinsed clean dry with a cloth and let air dry for 24 hours Rotate filter screen clockwise to lock in place Rinse with water only do not use detergent or soap Allow filter to dry 24 hours before putting it back into the dust bin When the cleaning of the filter no longer restores vacuum cleaner suction to full power you need to replace the filter s a good idea to clean the inside of the dust bin and lid area Rotate filter clockwise until slots lock onto tabs in lid NOTE Under normal use and care your fil ter can be expected to last up to 3 years NOTE See Parts and Features for Filter number 15 The secondary filter screen protects the motor Always check filter screen when cleaning dust bin If dirty or clogged remove debris from filter screen 16 A WARNING Electrical Shock Hazard Unplug power cord from electrical out let Do not operate the vacuum cleaner without the primary or exhaust filters Be sure the filters are properly installed to prevent motor failure and
9. domicilio y para ordenar piezas 1 800 LE FOYER 1 888 SU HOGAR 1 800 533 6937 1 888 784 6427 WWW sears ca O Sears Roebuck and Co Registered Trademark Trademark Service Mark of Sears Brand LLC Marca Registrada Marca de F brica 5 Marca de Servicio de Sears Bra Roebuck ands LLC MC Marque de commerce 2 Marque d pos e de Sears Brands LLC
10. dust bin Unplug before connecting Handi mate Jr if applicable You are responsible for making sure that your vacuum Cleaner is not used by anyone unable to operate it properly SAVE THESE INSTRUCTIONS Proper assembly and safe use of your vacuum cleaner are your responsibilities Your vacuum cleaner is intended for Household use Read this Owner s Manual carefully for important use and safety information This guide contains safety statements under warning and caution symbols Part No Part No in USA in Canada Exhaust Filter 20 86880 20 40320 Primary Filter DCF 1 20 82720 20 40319 20 5248 o 20 40096 Release Primary Filter Dust Bin Stretch Exhaust Hose Filter O We LA Adjustment a N L Base Handle Belt Release Y Underneath injury and or property damage Please pay special attention to these hazard alert boxes and follow any instructions given WARNING statements alert you to such dangers as fire electric shock burns and personal injury CAUTION statements alert you to such dangers as personal Electrical Shock Hazard Do not plug into the electrical supply until the assembly is complete Failure to do so could result in electrical shock or injury Before assembling vacuum cleaner check the PACKING LIST on the cover of the sep arate Repair Parts List Use this list to verify that you have received a
11. e a door on cord or pull cord around sharp edges or corners Do not run vacuum cleaner over cord Keep cord away from heated surfaces Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or vacuum cleaner with wet hands Do not put any objects into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Turn off all controls before unplugging Use extra care when cleaning on stairs Do not put on chairs tables etc Keep on floor Do not use vacuum cleaner to pick up flamma ble or combustible liquids gasoline cleaning fluid perfumes etc or use in areas where they may be present The fumes from these substances can create a fire hazard or explo sion Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use vacuum cleaner without dust bin and or filters in place Always clean the dust bin after vacuuming car pet cleaners or freshener powders and fine dust These products clog the filters reduce airflow and can cause damage to the vacuum cleaner Failure to clean the dust bin could cause perma nent damage to the vacuum cleaner Do not use the vacuum cleaner to pick up sharp hard objects small toys pins paper clips etc They may damage the vacuum cleaner or
12. icks up 1 Wrong pile height setting Adjust setting moveable rugs or pushes foo hard Light won t work 1 Burned out light bulb Change light bulb Agitator does not turn 1 Broken belt Replace belt 2 Belt installed incorrectly 2 Check BELT CHANGING AND AGITATOR CLEANING Air flow restricted 1 Attachment use restricts air flow Check ATTACHMENTS with attachment use 2 New carpet fuzz clogged air path Check CLOG REMOVAL and clean Sound changes hose 24 or maintenance agreement Canada on a product serviced by Sears A Your Home For repair in your home of all major brand appliances lawn and garden equipment or heating and cooling systems no matter who made it no matter who sold itl For the replacement parts accessories and owner s manuals that you need to do it yourself For Sears professional installation of home appliances and items like garage door openers and water heaters 1 800 4 MY HOME Anytime day or night 1 800 469 4663 U S A and Canada www sears com www sears ca Our Home For repair of carry in products like vacuums lawn equipment and electronics call or go on line for the nearest Sears Parts and Repair Center 1 800 488 1222 Anytime day or night U S A only www sears com To purchase a protection agreement U S A 1 800 827 6655 U S A 1 800 361 6665 Canada Para pedir servicio de reparaci n Au Canada pour service en fran ais a
13. ll the components of your new Kenmore vacuum cleaner HANDLE Remove the screw located just below the top edge of the back of the vacuum cleaner Slide the handle into the opening at the top of the vacuum cleaner Insert the screw so it passes through the handle into the vacuum cleaner Begin to tighten the screw with your fin gers It may be nec essary to adjust the handie slightly Using a screwdriver tighten the screw AX CAUTION Do not overtighten Overtightening could strip the screw holes Do not operate the vacuum cleaner without the screw in place HOSE Loop the hose over handle and align J slots in hose with tabs on the exten sion wand Push the hose onto the wand and twist to lock in place gt Rm J Slot ATTACHMENTS TO INSERT HANDI MATE JR Place Handi Mate Jr into the storage DUSTING BRUSH compartment Place the dusting brush Dusting Push the Handi Mate Jr down until it into the back of the handle Brush snaps into place in the storage location as shown Handi Mate Jr O HANDI MATE JR For operation of Handi Mate Jr see seperate owners manual TO REMOVE HANDI MATE JR Pull Handi Mate Jr out of the storage compartment OPERATING INSTRUCTIONS eon cee Push the power cord into the cord locking notch on the back of the handle Personal Injury and Product Damage Hazard DO NOT plug in if switch is i
14. lockwise from the locked position to the unlocked position as shown Unlock 13 Separate the lid from the dust bin by lifting it straight off Empty con tents into a trash con tainer _ TO REPLACE DUST BIN LID Trash Container Place dust bin lid assembly back onto top of dust bin Align marks with bin marks as shown Rotate lid clockwise while pressing downward so that marks align as shown Unlock Locked TO REPLACE DUST BIN First align base of dust bin with the vacuum cleaner Then rotate dust bin in place making sure dust bin is securely latched 14 Lid The Lid houses the filter Primary Filter Filter traps dirt and debris that is picked up by the suction motor Filter Screen The filter screen traps larger particles of dirt and debris from reaching the filter Dust Bin l Captures dirt and debris picked up from the suction motor A ds A HER RG Check primary filter frequently and clean Before replacing the primary filter it is a good when dirty Remove the dust bin assembly idea to clean the inside of the dust bin and lid as outlined in the DUST BIN CLEANING area section and empty contents of dust bin Make sure dust bin is empty before filter is removed Grasp filter screen rotate counter clockwise and lift out Primary Rotate filter clockwise until slots lock onto tabs in lid To re install the filter screen align ta
15. n the ON position Personal injury or damage could result DO NOT use outlets above counters Damage from cord to items in sur rounding area could occur Plug the polarized power cord into a 120 Volt outlet located near the floor Note To reduce the risk of electric shock this vacuum cleaner has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way SUGGESTED PILE HEIGHT SETTINGS Turn off vacuum cleaner Select a pile height You may need to raise the height to make setting by tilting the vacuum cleaner back some jobs easier such as scatter rugs and until front wheels are lifted slightly off the longer pile carpets Suggested settings are floor as illustrated HIGH shag carpet long pile plush scatter Slide the adjustment lever to the correct rugs setting MED medium to long pile LOW short to medium pile BARE FLOOR very low pile Release the handle by pressing down on the handle release pedal with your foot and pulling back and down on the handle with 4 your hand 4 Z N Handle Release Pedal To start the vacuum cleaner push the On Off switch from the OFF position to the ON position To stop the vacuum cleaner push the On Off switch to the OFF
16. n wear out from normal use including but not limited to filters belts light bulbs and bags 2 A service technician to instruct the user in correct product assembly operation or maintenance 3 A service technician to clean or maintain this product 4 Damage to or failure of this product if it is not assembled operated or maintained according to all instructions supplied with the product 5 Damage to or failure of this product resulting from accident abuse misuse or use for other than its intended purpose 6 Damage to or failure of this product caused by the use of detergents cleaners chemicals or utensils other than those recommended in all instructions supplied with the product 7 Damage to or failure of parts or systems resulting from unauthorized modifications made to this product Disclaimer of implied warranties limitation of remedies Customer s sole and exclusive remedy under this limited warranty shall be product repair as provided herein Implied warranties including warranties of merchantability or fitness for a particular purpose are limited to one year or the shortest period allowed by law Sears shall not be liable for incidental or consequential damages Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages or limitations on the duration of implied warranties of merchantability or fitness so these exclusions or limitations may not apply to you This warrant
17. o so could result in electrical shock or personal injury from vacuum cleaner suddenly starting If the vacuum cleaner does not seem to have adequate suction first check if the dust bin is full or if a filter is clogged See DUST BIN CLEANING and FILTER CHANGING If the dust bin and filter areas are free of clogs check the hose area Remove the lower end of the stretch hose from the vacu um cleaner by grasping the hose collar twisting and pulling straight out Plug in the vacuum cleaner and turn it on Stretch the hose to maximum length and then allow the hose to return to its storage length Turn the vacuum cleaner off and unplug the vacuum cleaner Visually inspect the hose and the base area into which the hose is inserted Remove any visible clog 21 Reassemble the stretch hose to the exten sion wand Collar If the dust bin and filter areas and the hose areas are free of clogs check the nozzle area To check this area see the section on BELT CHANGING AND AGITATOR CLEANING WARNING Personal Injury Hazard DO NOT piace hands or feet underneath the vacuum cleaner at any time The agitator will be revolving rapidly when the vacuum cleaner is turned on and is in the carpet setting Return vacuum cleaner to the upright posi tion before plugging into an electrical outlet A WARNING Electrical Shock Or Personal Injury Hazard Disconnect electrical supply before se
18. og Removal 0 0 21 Light Bulb Changing 22 Agitator Servicing 23 Troubleshooting 24 Requesting Assistance Or Service c0oo omo Back Page Please read this guide It will help you assemble and operate your new Kenmore vacuum cleaner in the safest and most effective way Model No Serial No Date of Purchase For more information about vacuum cleaner care and operation call your nearest Sears store You will need the complete model and serial numbers when requesting information Your vacu um cleaner s model and serial numbers are located on the Model and Serial Number Plate Use the space below to record the model number and serial number of your new Kenmore vacuum cleaner Keep this book and your sales check receipt in a safe place for future reference One Year Limited Warranty When assembled operated and maintained according to all instructions supplied with the product if this vacuum cleaner fails due to a defect in material or workmanship within one year from the date of purchase return it to any Sears store Sears Parts amp Repair Center or other Kenmore outlet for free repair If this vacuum cleaner is used for other than private family purposes this warranty applies for only 90 days from the date of purchase This warranty covers only defects in material and workmanship Sears will NOT pay for 1 Expendable items that ca
19. or electri cal shock EXHAUST FILTER The exhaust filter must be replaced when dirty It should be replaced regularly depending on use conditions The filter CANNOT be washed as it will lose its dust trapping ability NOTE See PARTS AND FEATURES for the exhaust filter number 47 Pull out on both sides of the exhaust filter cover and pull out to remove from vacuum cleaner A Pull Here Remove the exhaust filter cartridge i Push only on filter Exhaust N cartridge frame not on filter material itself Replace the exhaust filter cover by placing tabs in slots and pushing in until cover snaps into place A WARNING Electrical Shock Or Personal Injury Hazard Disconnect electrical supply before servicing or cleaning the vacuum cleaner Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting CLEANING AGITATOR To clean agitator turn vacuum cleaner over cut off any carpet pile and lint entangled around agitator with a pair of scissors as shown Frequently check and remove hair string and lint build up in the brush area If build up becomes excessive follow the steps below TO REMOVE BELT Disconnect power cord from electrical outlet and place on paper to protect the floor surface Place vacuum cleaner in the full upright posiiton Turn the vacuum cleaner over so the agi tator and base pl
20. r vicing or cleaning the vacuum cleaner Failure to do so could result in electri cal shock or personal injury from vacu um cleaner suddenly starting AX CAUTION Do not use a bulb rated over 13 V AC 9W During extended use heat from the bulb could overheat surrounding plastic parts CAUTION Do not plug in or turn on until the vacu um cleaner is completely reassembled 22 Ensure ON OFF switch is OFF Disconnect power cord from electrical outlet Press handle release pedal and rotate the handle down so the vacuum cleaner is lay ing flat on the floor Pry out light lens at slots Remove old bulb from the socket by pulling from socket Replace bulb by pressing into socket Only Use a bulb rated 13 V AC 9 Watts Reinstall light lens by snapping into place Return the vacuum cleaner to the upright position AA WARNING Electrical Shock Or Personal Injury Hazard Disconnect electrical supply before ser vicing or cleaning the vacuum cleaner Failure to do so could result in electri cal shock or personal injury from vacu um cleaner suddenly starting Turn the vacuum cleaner over to TO CHECK AGITATOR check for worn brushes When brushes are worn to the level of the AAA base belt guard replace the agita Base Plate Belt Guard tor 23 TO REPLACE AGITATOR Remove the nozzle cover agitator cover and agitator assembly See BELT C
21. y applies only while this vacuum cleaner is used in the United States and Canada This warranty gives you specific legal rights and you may also have other rights which vary from state to state Sears Roebuck and Co Hoffman Estates IL 60179 Sears Canada Inc Toronto Ontario Canada M5B 2B8 A WARNING IMPORTANT SAFETY INSTRUCTIONS Your safety is important to us To reduce the risk of fire electrical shock injury to persons or damage when using your vacuum cleaner follow basic safety precautions including the following Read all instructions in this manual before assembling or using your vacuum cleaner Use your vacuum cleaner only as described in this manual Use only with Sears recommend ed attachments Disconnect electrical supply before servicing or cleaning out the brush area Failure to do so could result in the brush unexpectedly starting causing personal injury from moving parts Do not leave vacuum cleaner when plugged in Unplug from outlet when not in use and before servicing To reduce the risk of electrical shock Do not use outdoors or on wet surfaces Do not allow to be used as a toy Close atten tion is necessary when used by or near chil dren Do not use with a damaged cord or plug If vacuum Cleaner is not working as it should has been dropped damaged left outdoors or dropped in water return it to a Sears Service Center Do not pull or carry by cord use cord as a handle clos
22. z filling the dust bin quickly See the TROUBLESHOOTING section VACUUM CLEANER CARE Always follow all safety precautions when cleaning and servicing the vacuum cleaner WARNING Electrical Shock And Personal Injury Hazard Disconnect electrical supply before servicing or cleaning the vacuum cleaner Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting Unplug cord from wall outlet Clean exterior using a clean soft cloth that has been dipped in a solution of mild liquid detergent and water then wrung dry Wipe dry after cleaning DO NOT drip water on vacuum cleaner Wash attachments in warm soapy water rinse and air dry Do not clean in dish washer 12 AX CAUTION Do not use attachments if they are wet Attachments used in dirty areas Such as under a refrigerator should not be used on other surfaces until they are washed They could leave marks CAUTION Electrical Shock And Personal Injury Hazard Always unplug power cord from electri cal outlet before performing any service on vacuum cleaner Release Lever TO REMOVE DUST BIN Remove dust bin assembly from vacuum cleaner by lift ing the release lever as shown y Remove dust bin from vacu um cleaner by tilting out as shown TO EMPTY DUST BIN Hold dust bin over a trash container Rotate lid counter c
Download Pdf Manuals
Related Search