John Lewis JLTDC10 Clothes Dryer User Manual
Contents
1. 1 2 Programme selector and Off switch Extra delicate button Intensive button Long anti crease button Alarm button Bal Time button Before first use Warning If the appliance was not transported in an upright position leave it to stand for 12 hours before connecting it to the electricity supply and using it for the first time so that the oil can flow back to the compressor Otherwise the compressor could be damaged 3 4 5 678 Display Dry time EJ Start Pause button 9 Warning lights Condenser Filter Full tank Delay start button In order to remove any residues which may have been produced during production wipe the dryer drum with a damp cloth or carry out a brief drying cycle 30 MIN with damp cloths in the machine Programme chart Additional A functions options 5 E c f g S2i8ly 9 r Programmes x 2 2 215 Elo s Application properties ff ole Els siglt Fis 2 A Wi e Pape Thorough drying of thick or multi layered fabrics Cottons Extra dry Ij 2 ke i i e g terry towelling items bathrobes cottons Cottons Store 7 ofe ded Thorough drying of thick fabrics e g terry dry 8 towelling items towels cottons Eston Thorough drying of fabrics of even thicknesses 7kg e g terry towelling items knitwear towels cotton 1 Cupboard dry Shirts Cottons Damp 7 Da a a O alles For thin textiles which are2. The water reservoir is full Empty the water reservoir then start programme with Start Pause button Drying cycle ends shortly after programme starts END display Not enough washing loaded or washing loaded is too dry for Select time programme or higher drying level e g INTENSIVE DRY instead of STORAGE illuminated selected programme DRY Lint filter clogged Clean lint filter Fluff filter clogged Clean fluff filter Drying cycle lasts an unusually Load volume too big Reduce load volume long time Note After around 5 Laundry must be adequately spun hours the drying cycle ends Laundry insufficiently spun automatically see Drying cycle complete Particularly high room temperature Temporary switching off of the compressor to avoid overload Automatic process there is no fault with the appliance If possible lower the room temperature Replacing the drum light Only use a special bulb which is designed specially for dryers The special bulb can be obtained from your local Service Force Centre Important When the appliance is switched on the interior lighting switches itself off after 4 minutes when the door is open A Warning Do not use standard bulbs These develop too much heat and may damage the machine Warning Before replacing the bulb disconnect the mains plug with a permanent connection fully unscrew or deactivat
3. In order to continue the programme the water reservoir must first be emptied Warning The condensed water is not suitable for drinking or for preparing foodstuffs 17 Take out drawer containing water reservoir completely 1 and pull up the water reservoir s drainage pipe as far as it will go 2 The condensed water can be used as distilled water e g for steam ironing However it must first be filtered e g with a coffee filter to remove any residue and small pieces of fluff Cleaning heat exchanger filter If the warning lamp Condenser lights the heat exchanger filter in the base of the appliance must be cleaned To protect the heat pump from dirt 2 Pour the condensed water out into a basin or similar receptacle the dryer is fitted with a fluff filter which is located in the filter housing Here too large amounts of fluff build up over time which affect the function of the appliance Important Operating when the fluff filter is clogged with fluff can damage the dryer This also increases energy consumption e Never operate the dryer without the fluff filters Slide the outlet connections in and refit the water reservoir If the programme has been interrupted as a result of the water reservoir being full Press the Start Pause button to continue the drying cycle The water reservoir has a volume of approx 4 litres This is sufficient for around
4. Loading door does not close Wrong programme selected Select a different programme the next time you dry see Programme chart chapter Lint filters clogged Clean lint filters Fluff filter clogged Clean fluff filter Overloading of laundry Observe recommended loading volumes Ventilation slots in base area covered up Uncover ventilation slots in base area Residue on inside surface of drum or drum ribs Fine strainer not in place and or mesh filter not locked in place Clean inside surface of drum and drum ribs Make an adjustment using the DRYNESS function see chapter Daily use Install fine strainer and or snap large mesh filter into place When a button is pressed Err appears on the LCD Washing protection After the start of the programme the option can no longer be set Turn the programme knob to Off Set the programme again Drum light does not work Programme selector in Off position Turn programme selector to LIGHT or to any programme Defective light bulb 21 Replace light bulb see next section Displayed programme time changes erratically or stays unchanged for a long time of dampness Programme time is corrected automatically depending on type and volume of laundry and level Automatic process this is not a machine fault Programme inactive empty water tank warning lamp Full tank lights
5. 14 Putting in extra items or taking items out before end of programme 15 Drying cycle complete removing laundry 15 Maintenance and cleaning 16 Cleaning fluff filter 16 Cleaning the door seal 17 Emptying the water reservoir 17 Cleaning heat exchanger filter 18 Cleaning the drum 20 Clean operating screen and housing 20 What to do if 21 Machine settings 23 For the installer Technical specifications 24 Installation 25 Transporting the appliance 25 Appliance positioning 25 Removing transport safety packaging 26 Electrical connection 26 Door reversal 27 Repairs after sales service 28 Guide to use the instruction manual The following symbols will be found in the text to guide you throughout the instructions AN Safety instructions i Hints and tips W Environmental information Description of the appliance Control panel Water reservoir Drum light Fine fluff filter Fluff filter 6 Loading door reversible Rating plate El Course fluff filter E Heat exchanger cover Push button for base door opening Ventilation grille Adjustable feet Control panel Easy iron O O Heavy cotton _ Long Extra delicate Intensive anti crease Dry time Delay start O Condenser O filter O Full tank Start Pause O O Alarm Time Time _____ _ g I Child lock
6. cycle before loading your tumble dryer e Please make sure that no gas lighters or matches have accidentally been left in pockets of garments to be loaded into appliance Warning Never stop a tumble dry before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated Risk of fire e Risk of electric shock Do not spray down the appliance with jets of water Installation e This appliance is heavy Care should be taken when moving it e When unpacking the appliance check that it is not damaged If in doubt do not use it and contact the Service Centre e All packing must be removed before use Serious damage can occur to the product and to property if this is not adhered to See relevant section in the user manual e The final part ofa tumble dryer cycle occurs without heat cool down cycle to ensure that the items are left at a temperature that ensures that items will not be damaged e Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person e Care must be taken to ensure that the appliance does not stand on the electrical supply cable e Ifthe machine is situated on a carpeted floor please adjust the feet in order to allow air to circulate freely e After having installed the appliance check that it is not pressing or standing on its electrical supply cable e Ifthe tumble dryer is p
7. not be placed into the machine In order to avoid danger of fires caused by excessive drying do not use appliance to dry the following items Cushions quilts and the like these items accumulate heat Items such as foam rubber latex foam shower caps waterproof textiles rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer e Always unplug the appliance after use cleaning and maintenance Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Centre Always insist on genuine spare parts Items that have been soiled with substances such as cooking oil acetone petrol kerosene spot removers turpentine waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer Danger of explosion Never tumble dry items that have been in contact with inflammable solvents petrol methylated spirits dry cleaning fluid and the like As these substance are volatile they could cause an explosion Only tumble dry items washed with water e Risk of fire items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be placed in the tumble dryer e If you have washed your laundry with stain remover you must execute an extra rinse
8. on Dryime Delay start O Condenser O Filter Full tank E oe Start Pause Extra delicate Intensive anti crease Alarm Time ari Child lock Fadiok B 2 Press the Time button repeatedly until the desired programme duration is shown in the display e g 20 for a programme of 20 minutes If the programme duration is not selected the duration is automatically set to 10 mins 13 Delay start Delay start O Condenser O Filter O O Full tank g 7 Hee Start Pause Extra delicate Intensive anti crease Alarm Time tart Pau Child lock amp With the Delay start button you can delay the start of a programme by between 30 minutes 30 and a maximum of 20 hours 20h i 1 Select the programme and additional functions 2 Press the Delay start button as many times as necessary until the required Delay start appears on the display e g 12h if the programme is to be started in 12 hours i If the display is showing 20h and you press the button again the time delay will be cancelled The display will show O and then the duration of the selected programme 3 To activate the delay timer press the Start Pause button The amount of time remaining until the programme is set to start is continuously displayed e g 15h 14h 13h 30 etc Setting child lock The child lock can be set to prevent a programme being accidentally started or a programme in op
9. parts please contact our extended warranty administrators by telephoning 0870 010 7887 They will give you details of your local Service Force Centre Before calling out an engineer please ensure you have read the details under the heading What to do if When you contact your local repair agent you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of fault 4 The purchase date found on your receipt 5 The model and serial number of the appliance found on the rating plate see picture Typ XX XXX XOXX KOX min xa KV PNC XXX XXX XXXXX S No XXXXXXXX cE c 28 So that you always have these numbers at hand we recommend that you make a note of them here Your dryer is covered by a 3 year parts and labour guarantee see separate details given at point of sale Please retain your purchase receipt safely for the service engineer to verify the purchase details Spare parts An authorised service engineer should service this product and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local repair agent by telephoning 0870 010 7887 29 30 31 John Lewis Partnership 171 Victoria Street London SW1E 5NN ww
10. still to be ironed e g dry 8 knitted item cotton shirts Cottons Iron 7 Tet For normal thickness cotton or linen laundry e g dry 8 bedding table linen Synthetics Extra 3 ote te le Thorough drying of thick or multi layered fabrics dry 8 e g pullovers bedding table linen Sthen For thin fabrics which are not ironed e g easy care H board daD 3kg e shirts table linen socks lingerie with bones or PP SORTS wires Synthetics Iron 3 o te fe For thin fabrics which are also to be ironed e g dry 8 knitwear cotton shirts Time 7kg For drying of individual items of laundry For leisure clothing such as jeans sweat shirts Heavy cotton 7kg e Jetc of different material thicknesses e g at the neck cuffs and seams Special program with anti crease mechanism for easy care fabrics such shirts and blouses for 1kg minimum ironing effort The results depends on Easy iron or5 e e e e the type of fabric and its finish Place fabrics in the shirts dryer straight after spinning once dried immediately remove fabrics and place on a clothes hanger Programmes max load weight when dry Additional functions options Extra delicate Intensive Long anti crease Alarm Time Delay start Application properties Refresh 1kg For refreshing or airing clothing that has been in storage Wool Si
11. the plug supplied a 13amp ASTA approved BS 1363 A fuse must be used Should the plug need to be replaced for any reason proceed as described below The wires in the mains lead are coloured in accordance with the following code e Green and Yellow Earth e Blue Neutral e Brown Live Warning If the appliance was not transported in an upright position leave it to stand for 12 hours before connecting it to the electricity supply and using it for the first time so that the oil can flow back to the compressor Otherwise the compressor could be damaged 26 CORD CLAMP If you fit your own plug the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug Proceed as follows 1 Connect the Green and Yellow earth wire to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow 2 Connect the Blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black 3 Connect the Brown live wire to the terminal in the plug which is marked with the letter L or coloured red 4 Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath Warning A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug
12. 7 kg of laundry which has previously been spun at 1000 revolutions minute 1 Open door in plinth To do this press the release button on the right and open the door in the plinth to the left 18 2 Pull the filter housing out of the base by the handle 3 Clean the inside of the door the fluff filter chamber and the rubber seals of fluff 4 Remove fluff from the fluff filter on the floor of the base with a damp hand Remove fluff from the fluff filter with a damp hand If necessary clean the filter under running water using a brush 5 To clean the fluff filter Remove the filter from the filter housing To do this press 7 Insert the fluff filter into the filter housing the pressure points on the sides and pull As necessary approx once every 6 the filter frame up and out of the housing coe 2 months remove the fluff from the heat exchanger using the sponge supplied When doing this please use rubber gloves 19 Lime in the water or cleaning agents may form a barely visible lining on the inside of the drum The degree to which the laundry has been dried is then no longer detected reliably The laundry is damper than expected when removed from the dryer Use a standard domestic cleaner e g vinegar based cleane
13. JLTDC10 Condenser dryer with heat pump Instruction manual John Lewis A Important safety information It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings These warnings have been provided in the interest of safety You MUST read them carefully before installing or using the appliance If you are unsure of the meanings of these warnings contact the John Lewis branch from which you purchased the appliance General safety This appliance is designed to be operated by adults It is dangerous to alter the specifications or attempt to modify this product in any way This appliance is not intended for use by persons including children with reduced physical sensory or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Make sure that small pets do not climb into the drum To avoid this please check into the drum before using Any objects such as coins safety pins nails screws stones or any other hard sharp material can cause extensive damage and must
14. ai Child lock une If this additional function is selected the anti crease phase at the end of the drying cycle is lengthened by 60 minutes The laundry can be removed at any time during the anti crease phase To deselect the function press the Long anti crease button again The LED above is off Press the Long anti crease button A 90 minute anti crease phase is set The display now shows the Long anti crease icon If this additional function is selected the anti crease phase at the end of the drying cycle is lengthened by 60 minutes The laundry can be removed at any time during the anti crease phase Alarm The appliance is supplied with the Alarm function deactivated When activated the buzzer sounds At the end of the cycle When the anti crease phase starts or ends When the cycle is interrupted To activate it 1 Choose the drying programme 2 Press the Alarm button the LED above is on Dry ume Delay start O Condenser O Filter O oO O Full tank Extra delicate Intensive ante crease Alarm Time Start Pause Child lock sri tock B To deselect the function press the Alarm button again The LED above is off Time Use the Time button to select the programme duration after setting the Time programme You can select a programme duration from 10 mins to 2 hrs in 10 minute steps 1 Turn the programme selector to the Time programme The flashing 10 above the Time button is
15. creases from forming If Long anti crease function has been selected the anti crease phase is lengthened by 60 minutes 1 Open door 2 Before removing the laundry remove fluff from the micro fine filter It is best to use a damp hand for this purpose See Maintenance and cleaning chapter 3 Remove laundry 4 Turn the programme selector to Off Important After each drying cycle Clean the micro fine filter and fine filter Drain the condensed water container See chapter Maintenance and cleaning 5 Close the door 15 Maintenance and cleaning Cleaning fluff filter The filters collect all the fluff which accumulates during drying To ensure that the dryer works perfectly the fluff filters micro fine filter and fine strainer must be cleaned after every drying cycle The warning lamp Filter lights to remind you of this operation at the end of each cycle Caution Never operate the dryer without fluff filters or with damaged or blocked fluff filters 1 Open loading door 2 Use a damp hand to clean the micro fine filter which is built into the lower part of the loading aperture After a period of time a patina due to detergent residue on laundry forms on the filters When this occurs clean the filters with warm water using a brush Remove the filter from the door pulling it out It can be positioned with the locating spur facing to the left or to th
16. d for drying sensitive fabrics with the care label and for temperature sensitive textiles e g acrylic viscose The programme is executed with reduced heat To activate it 1 Choose the drying programme Dry time rd start E Consens O Filter o O Full tank e Extra delicate Intensive ani Po eae Alarm Start Paus PCL T 2 Press the Extra delicate button the LED above is on To deselect the function press the Extra delicate button again LED above is off a Child lock amp Intensive If the laundry is still damp after a standard drying programme you can increase the drying result by using the Intensive function 1 Choose the drying programme Diy tine Delay start O Condenser O Filter O O Full tank Extra delicate Intensive oe crease Alarm Time Start Pause E Child lock 2 Press the Intensive button the LED above is on 12 To deselect the function press the Intensive button again The LED above is off Long anti crease This function prolongs the anti crease phase to 90 mins in total The drum rotates in intervals during this phase The laundry therefore remains relaxed and free of creases To activate it 1 Choose the drying programme 2 Press the Long anti crease button the LED above is on Dy me Delay start O Condenser O Filter O O Full tank o E ras 2 Start Pause Extra delicate Intensive anti crease Alarm Time tart P
17. e right After cleaning do not forget to put it back 16 4 Push down the unlock button on the large mesh filter The large mesh filter pops up 5 Take out fine filter 6 Remove the fluff from fine filter It is best to use a damp hand for this purpose i Clean the entire filter area The filter area does not have to be cleaned after every drying cycle but should be checked regularly and cleaned of fluff if necessary 7 Todo this grip the top of the large mesh filter and pull it forwards until it comes loose from the two brackets 8 Remove fluff from the entire filter area It is best to use a vacuum cleaner for this purpose 9 Press both journals of the large mesh filter into the brackets on the loading door until they snap into place 10 Re insert fine filter 11 Press against the large mesh filter until it locks into the interlock If the fine filter is not fitted the large mesh filter will not snap into place and the loading door cannot be closed i Cleaning the door seal Wipe the door seal with a damp cloth immediately after the drying cycle has finished Emptying the water reservoir Empty the water reservoir after every drying cycle If the water reservoir is full an active programme will break off automatically and the warning lamp Full tank lights
18. e the fuse A 1 Unscrew the cover above the bulb this can be found directly behind the loading aperture at the top refer to Description of machine section 2 3 Screw cover back down Check the correct positioning of o ring gasket before screwing back the door light cover Do not operate the dryer when missing o ring gasket on door light cover JN Replace the defective bulb Warning For safety reasons the cover must be screwed down tightly If this is not done the dryer must not be operated 22 Machine settings ALARM permanent on off The alarm is by default always off To set 2 Press simultaneously the Intensive and permanent alarm on off Long anti crease buttons and hold 1 Turn the programme selector to any down for approx 5 seconds programme Adjusting the level of conductivity Water contains a variable quantity of 3 Press the Start Pause button until you limestone and mineral salts of which set desired level quantities vary according to geographical a locations thus varying its conductivity COL l w conduetivity lt 300 uS cm values Relevant variations of the conductivity of COz medium conductivity the water compared to those prefixed by 300 600 uS cm the factory could slightly influence the C0 high conductivity residual humidity of the laundry at the gt 600 uS cm end of the cycle Your dryer allows youto 4 To memorize setting press sim
19. eration being accidentally changed The child lock function locks all buttons and the programme selector The child lock can be activated or deactivated by holding down the Extra delicate and Intensive buttons simultaneously for 5 seconds Before programme is started Appliance cannot be used i After programme is started Programme in operation cannot be changed The icon amp appears in the display to indicate that the child safety device is activated Dry time Delay start O O O O O Long anti crease Alarm Time Py f The child safety device is not deactivated once the programme comes to an end If you want to set anew programme you must first deactivate the child safety device Extra delicate Intensive Child lock amp Starting the programme Press the Start Pause button The programme starts The programme progress is shown by elapsing Dry time on LCD Dry time Delay start 320 Cou O Condenser O Filter Oo O Full tank O oO o Long O me Start Pause Extra delicate Intensive anti crease Alarm Ti BERRE Child lock Changing programme To change a programme which has been selected by mistake once the programme has started first turn the programme selector to Off and then reset the programme The programme can no longer be changed directly once the programme has started If nevertheless there is an attempt to change the programme on the pr
20. es as a result of different measuring methods in accordance with IEC 61121 7 kg load pre drained at 1000 rpm 3 kg load pre drained at 1200 rpm 24 Installation Transporting the appliance Important Only tip the appliance on its left side to transport see illustration if it cannot be transported in an upright position Appliance positioning e It is recommended that for your convenience the machine is positioned close to your washing machine e The tumble dryer must be installed in a clean place where dirt does not build up 25 e Air must be able to circulate freely all round the appliance Do not obstruct the front ventilation grille or the air intake grilles at the back of the machine e To keep vibration and noise to a minimum when the dryer is in use it should be placed on a firm level surface Once in its permanent operating position check that the dryer is absolutely level with the aid of a spirit level If it is not raise or lower the feet until it is The feet must never be removed Do not restrict the floor clearance through deeppile carpets strips of wood or similar This might cause heat built up which would interfere with the operation of the appliance Important The hot air emitted by the tumble dryer can reach temperatures of up to 60 C The appliance must therefore not be installed on floors which are not resistant to high temperatures When ope
21. is disposed of safely Warning The plug must still be accessible after the appliance has been installed Warning The appliance should not be connected to the electrical supply by means of an extension cable AN Warning The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precautions Should the appliance power supply cable need to be replaced this must be carried out by our Service Centre A Warning The power supply cable must be accessible after installing the machine A Permanent connection In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply mains with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations The switch must not break the yellow and green earth cable at any point Door reversal To make it easier to load or unload the laundry the door can be reversed Warning The door must only be reversed by an authorised service engineer Please contact your nearest John Lewis branch who will give you details of your local Service Force Centre The engineer will carry out the door reversal at your cost Repairs after sales service If the unlikely event of your appliance requiring service or if you wish to purchase spare
22. laced on top of a washing machine it is compulsory to use the stacking kit optional accessory Use e This appliance is designed for domestic use It must not be used for purposes other than those for which it was designed e Only dry fabrics which are designed to be machine dried Follow the instructions on each garment label e Do not dry unwashed items in the tumble dryer Do not overload the appliance See the relevant section in the user manual Clothes which are dripping wet should not be placed in the dryer e Garments which have been in contact with volatile petroleum products should not be machine dried If volatile cleaning fluids are used care should be taken to ensure that the fluid is removed from the garment before placing in the machine e Never pull the power supply cable to remove the plug from the socket always take hold of the plug itself e Never use the tumble dryer if the power supply cable the control panel the working surface or the base are damaged so that the inside of the tumble dryer is accessible e Fabric softeners or similar products should be used as specified by the fabric softener instructions e Caution hot surface Do not touch the door light cover surface when the light is switched on Child safety This machine is not intended for use by young children or infirm persons without supervision This appliance is designed to be operated by adults Child
23. lk 1kg 1kg For drying woollen fabrics after they have been washed using warm air at minimum mechanical load Follow section Sorting and preparing washing Recommendation Remove fabrics immediately after drying as no anti crease programme follows For drying silk using warm air and gentle movement 1 In accordance with EN61121 10 Sorting and preparing laundry Sorting laundry Do not dry cotton jersey and knitwear with Sort by fabric type the Extra programme Items may shrink Cotton linen for programmes in e Wool and wool like textiles can be dried Cottons programme group using the Wool programme Before the Mixtures and synthetics for programmes drying cycle spin the woollen textiles as well in Synthetics programme group as possible max 1200 rpm Only dry woollen textiles together of similar or the same material colour and weight Please Drying in the tumble dryer possible in dry heavy laundry items made of wool principle separately Preparing laundry Sort by care label The care labels mean C Drying at normal temperature e To avoid laundry becoming tangled close FN e CJ Drying at reduced temperature zips button up duvet covers and tie loose amp Drying in the tumble dryer not possible ties or ribbons e g of aprons e Empty pockets Remove metal items Important Do not place in the appliance paper clips safe
24. ogramme knob the programme progress display and the maintenance indicators flash If an option button excluding the Alarm button is pressed Err appears in the multidisplay l The drying programme is not however affected by this laundry protection Putting in extra items or taking items out before end of programme 1 Open loading door Warning Laundry and drum can become hot Risk of burns 2 Load or remove laundry items 3 Close loading securely Lock must audibly lock 4 Press the Start Pause button to continue the drying cycle Drying cycle complete removing laundry Once the drying cycle is complete the display shows the anti crease icon and flashing 0 as well as warning lamps Filter and Full tank If the Alarm button has been pressed an acoustic signal sounds intermittently for about one minute Drysine Delay start i ul Condenser Filter O Full tank 7 ae o Start Pause Extra delicate Intensive anti crease Alarm Time l ri Child lock amp e The drying cycles except from the Wool programme are automatically followed by an anti crease phase which lasts around 30 minutes The drum rotates at intervals during this phase This keeps the laundry loose and free of creases The laundry can be removed at any time during the anti crease phase The laundry should be taken out towards the end of the anti crease phase at the latest to prevent
25. r to wipe down the inside of the drum and drum ribs e The fluff can be removed more easily Clean operating screen if it is first dampened e g with a and housing laundry dampener It is best to use a vacuum cleaner for this purpose Caution Do not use furniture Do not use any sharp objects in cleaners or aggressive cleaning agents this area to clean the machine Use a damp cloth to wipe down the 9 Re insert filter housing along with filter in operating screen and housing appliance base If the fluff filter is not inserted in the filter housing the filter housing cannot be slid into the appliance base 10 Close door in plinth Cleaning the drum Caution Do not use abrasives or steel wool to clean the drum 20 What to do if If during operation the error code E plus number or letter appears on the LCD Switch the machine off and on again to reset the error code programme Press the Start Pause button If the error is still displayed please inform your local Service Force Centre and quote the Problem Possible cause Remedy Dryer does not work Mains plug is not plugged in or fuse is not working correctly Plug in at mains socket Check fuse in fuse box domestic installation Loading door is open Close loading door Have you pressed the Start Pause button Press the Start Pause button again Drying results unsatisfactory
26. rating the tumble dryer the room temperature must not be lower than 5 C and higher than 35 C as it may affect the performance of the appliance Warning Should the appliance be moved it must be transported vertically AN Warning The appliance must not be installed behind the lockable door a sliding door a door with a hinge on the opposite side to that of the appliance Removing transport safety packaging Caution Before use all parts of the transport packaging must be removed Open loading door Pull off adhesive strips from inside machine on top of drum olo olo oa 20000 20000 oo Remove foil hose and polystyrene padding from the machine 7 A Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Warning THIS APPLIANCE MUST BE EARTHED Should the appliance power supply cable need to be replaced this must be carried out by a Service Force agent see chapter Repairs after sales service The manufacturer declines any liability should this safety measure not be observed Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance s rating plate See picture on page 6 The appliance is supplied with a 13amp plug fitted In the event of having to change the fuse in
27. ren should be supervised to ensure that they do not play with the appliance The packaging components e g plastic film polystyrene can be dangerous to children danger of suffocation Keep them out of children s reach Keep all detergents in a safe place out of children s reach Make sure that children or pets do not climb into the drum Environmental tips e In the dryer laundry becomes fluffy and soft Fabric softeners are not therefore needed when washing Your dryer will function most economically if you Always keep the ventilation slots on the base of the dryer unobstructed Use the loading volumes specified in the programme overview Ensure you have good ventilation in the installation room Clean the micro fine filter and fine strainer after each drying cycle Spin the laundry well before drying 1 Only dryers equipped with internal drum light Energy consumption depends on spinning speed set in washing machine Higher spinning speed lower energy consumption w Environmental information The packaging materials are environmentally friendly and can be recycled The plastic components are identified by markings e g gt PE lt gt PS lt etc Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities Important The heat pump of your dryer contains a closed refrigerant circuit filled with a refrigerant
28. ty pins etc any wet laundry which is not specified on the e Turn items with double layered fabrics care label as being suitable for tumble drying inside out e g with cotton lined anoraks This appliance can be used for all wet laundry the cotton layer should be outermost items which are labelled as suitable for These fabrics will then dry better tumble drying e Donot dry new coloured textiles together with light coloured laundry items Textile colours may bleed Daily use Switching machine on Door opening and laundry Turn the programme selector to any loading programme The machine switches on When the loading door is open the internal lam te SP eee yee PEN i Push against the loading door push point illuminates the drum 11 2 Load your laundry do not force it in Caution Do not jam laundry in between the loading door and rubber seal 3 Close loading door securely Lock must audibly lock Selecting the programme Silk Off Wool Refresh gt Easy iron e Heavy cotton _ Time ee Use the programme selector to set the programme you require The estimated time to end of the programme appears in the LCD in h mm format hours minutes During the cycle time elapses by steps of one minute less than 1 hour the leading zero is not shown e g 59 5 0 Extra delicate Extra delicate cycle is a programme specially designe
29. ultaneously regulate the sensitivity of the drying the Long anti crease and Start sensor based on conductivity values of the Pause buttons or turn knob to Off water position 1 Turn the programme selector to any programme 2 Press simultaneously the Long anti crease and Start Pause buttons and hold down for approx 5 seconds 23 Technical specifications 1 2 3 4 This appliance conforms with the following EU Directives 2006 95 EC dated 12 12 2006 Low Voltage Directive 89 336 EEC dated 03 05 1989 EMC Directive inclusive of Amending Directive 92 31 EEC 93 68 EEC dated 22 07 1993 CE Marking Directive Height x width x depth 85 x 60 x 58 cm Drum volume 108 Depth with loading door open 109 cm Height can be adjusted by 1 5 cm Weight when empty approx 60 kg Loading volume depends on programme max 7 kg Voltage 230 240 V Required fuse 13 A Total power 1350 W Energy efficiency class A E nani Use Domestic Permissible ambient temperature 5 C to 35 C Consumption values The consumption values have been established under standard conditions They may deviate when the machine is operated in domestic circumstances Programme Energy consumption in kWh COTTON CUPBOARD DRY 3 COTTON IRON DRY 2 3 2 4 1 8 SYNTHETICS CUPBOARD DRY 2 4 0 75 Different loading volume data may be needed in some countri
30. w johniewis com 136904440 02 07042008
31. which is free from fluoro chloro hydrocarbons The refrigerant circuit in the heat pump must not be damaged Warning When a unit is no longer being used e Pull the plug out of the socket e Cut off the cable and plug and dispose of them e Dispose of the door catch This prevents children from trapping themselves inside and endangering their lives The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product Contents For the user Important safety information Description of the appliance 2 7 Control panel 8 Before first use 8 9 Programme chart Sorting and preparing laundry 11 Daily use 11 Switching machine on 11 Door opening and laundry loading 11 Selecting the programme 12 Extra delicate 12 Intensive 12 Long anti crease 13 Alarm 13 Time 13 Delay start 14 Setting child lock 14 Starting the programme 14 Changing programme
Download Pdf Manuals
Related Search