Jacuzzi J-ALLURELuxury Bathing and Entertainment System Hot Tub User Manual
Contents
1. GUIDE 20 OPERATING INSTRUCTIONS CENTER PANEL System control is provided by the electronic display located on the center panel The display is used to start up the five functions of the unit the hand held shower the fixed shower the hydromassage all jets hydromassage pulsed jets and the steam bath The display is composed of clear symbols to identify the five functions STEAM JETS START PULSED JETS START BUTTON BUTTON START BUTTON WHIRLPOOL BATH SYSTEMS CONTROL CENTER HAND HELD SHOWER STATIONARY SHOWER OFF BUTTON START BUTTON START BUTTON FIGURE 1 CENTER PANEL AND DISPLAY Starting Any Function The mixer control valve must be ON for the functions of the center panel to be operational After the mixer valve has been set and is ON press any button to start that function The steam function can be ON with any other function Other functions can only be ON one at a time Pressing the OFF button turns all functions OFF Mixer Control To adjust the temperature turn the mixer handle as shown in Figure 2 When exiting the J Allure with all OFF functions OFF the mixer control must be turned to the FIGURE 2 MIXER CONTROL OFF position Hand Held Shower Pressing the Hand Held Shower button once activates hand held shower and pressing a second time deactivates the shower Pressing the OFF button or any other button will turn the shower mode OFF Stationary Shower2. replacement parts equipment and repairs shall assume the remaining warranty period of the part s replaced The Company s warranty obligation shall be discharged upon tender of replacement or repair The customer s refusal to accept the tender terminates the Company s warranty obligation 1998 Jacuzzi Whirlpool Bath N115000C 12 02 c 2 ccr 8 EZ 9 RSS 9055055 lt 2 325 lt lt 5 Sz S 3 AR ONE 22333 ENDE C EA MERE S S S 883594 55555 gt 5275 gt gt zzz z z z gz 2255809 2929322 o 3 9 v os 9 550 5 5 5 ss 0 0 0 2229909 5 8 EZS ziizilvzER ilelsl gi n 2 l gozp2PQPOSISPOPGP 2Qricisiio EE S 22285 E lt lt o ae m e E D aga 8 585 529850 2 5289210 2922892899292002 92 59 9528228 gt 252 0 99 5 02 H B Ogn 2924555552205 2622252425850 sasan Eos 88525 9 89205 555 8889522222 BG 3 12 222252258 553525 582 5052854 a qe es On gt 33 oo 90ggg 2 gz 9s 5 59523 8 88 5 oca a s 0 wx 500 5 oz 3 35 Uu zc 3o 3 o m o axe 2 00085356 2687 20084 99 32 8 Pacaya 2053809 252359 ime a 3 06055p99022529 oX rtg9l 2 sEL PZg8 5932 9S 5eps2g 2
3. FOR MODELS WITH TV MAKE SUBE AUDIO CABLES FAN HOSES DO Nor AND TV POWER CORDS SAG OR DIP 1 X 4 NOT FOR SUPPORT NOTE Finished floor must be at the same level as the floor supporting the bath for the skirt to fit properly SKIRT SAME LEVEL AS FINISHED FLOOR FINISHED FLOOR x J Allure Rough in The installation requires three cutouts in the walls Two cutouts allow room for the speakers The third cutout is necessary to route water supply piping to the center panel and to route hoses for the steam generators to the bath The location of a 230 power outlet is indicated on the wall cutouts illustration Rough in Reference DRAIN OVERFLOW CUTOUT IN FLOOR I lt 72 7 16 J Allure Finished Walls Before fixing the bath in place make sure the finished walls above the rim of the bath are perpendicular The two wall extrusions at the edges of the fixed panels will allow some compensation for walls out of true less than 3 16 See fixed panels installation for wall extrusions If that is the case the bath may be placed against the finished walls If more than 3 16 shims will be necessary and the bath moved away from the wall an appropriate distance When final setting of the bath secure the metal straps attached to the bath to the floor with screws or anchors SHIM WALL EXTRUSION WALL EXTRUSION ES FINISHED WALL FINISHED WALL 90 90 SHI
4. SIDE WALL FRAME BATH RIM J Allure Side Walls Caulking After the side walls are installed they must be caulked with silicone sealant not provided Seal the entire length at the bottom and from the bottom to top where the side wall moulding meets the attached extrusion Also caulk the joint between the side wall extrusion and the fixed panel frame Apply the two foam tapes provided to side wall The first tape will butt up against the curve of the side wall with the second tape against the first tape Remove the facing paper from both Install the V seal as shown so that it covers the joint between the foam tapes TWO STRIPS OF FOAM TAPE SIDE BY SIDE FROM TOP TO BOTTOM ONLY ON RIGHT SIDE WALL WALL EXTRUSION SEALANT SIDE WALL SEALANT ALONG ENTIRE LENGTH OF SIDE WALL GLASS PANELS AND GUIDES NOT SHOWN FOR CLARITY J Allure Inside Caulking Caulk the joint between the lower guide and the bath FIXED PANELS LOWER GUIDE J Allure Sliding Doors Installation Take one of the doors inside the shower compartment The upper rollers will be fixed while the bottom rollers will be loose In a vertical position insert the upper and lower rollers at the same time into th
5. SCREW M3 5X50 Quantity 4 SET SCREW 5 9 9 Quantity 4 ACORN NUT M5 Quantity 4 FLAT WASHER Quantity 2 EXTERNAL TOOTH LOCK WASHER Quantity 6 SPACER Quantity 4 010000000 C WALL ANCHOR Quantity 6 J Allure Framing and Support The drain overflow of the bath extends below the bottom of the bath Note that this requires a cutout in the floor The floor structure beneath the bath must be able to supporta total weight of approximately 94 Ib sq ft bath water and bather If the subfloor is level no other preparation is necessary You can proceed to install the bath Ifthe subfloor is notlevel you MUST level the entire surface prior to installing the bath Use a floor leveling compound Do not level bath with mortar Both sides of a joint or splice of subfloor should be level to each other Before final setting of the bath route the steam hoses from under the shell through the cutout in the rim Unwind the speaker wires from under the bath rim on both sides When final setting the speaker wires must be routed under the 1x4 For units with TV unwind audio cables fan and TV power cords The protective film liner inside the bath should be left there to prevent damage to the finish from shoes tools etc during installation and should not be removed until final cleanup Typical Installation WALL CUTOUTS SPEAKER FINISHED WALL
6. E gt TE 5 5 lt 2 3886 59057 5 gt 482 B 82 35598 ES829 g2 142 8 256 Ies o a w a pan zspoooo g 2962 2 205685 254829 25323 6 T ao L 48 928 az os 8 25302 S S9 5 881935 8 iman fa n a 3 G lt o o ooc z 3595 Oo BOO 5 o 5 2 5 Fo Li 5 lt g o O2509Q gt 4 T Og z 5 an _ S 2 5 6228 08 805 58298055 9925 Foe 75 8554 5 S322 8 w r en 392522655 8 S 8 020 232 8 s gt 8 e Soc lt m IS A SS a ass S S e 93 25422 3 926 gt z So 9 9e e8S858 2985 S gt 9 5 R290 2 89 256 22 5 29 50688 229 4 29 27 Bec RBS 8 zs 3 4 gg 2285855 8842 085 25 24 9 gt 45 82 m o 228 22 gt 55 5 D oogoa3 MR 5 e oo a I o NO N 92522 Nd sal g 29204 g 888 9S 8 8 54 Q 9925 237 2 Se m o9 599 e gt o lt 2 2 s s 898055 883 oo 5 325025 82 85 5 2 8225 5 ss QI lt PROSAZ 2 55 0 S Sa O 8 Gees Zo o 2 Foose 5 i i 9583 55 s 585 E I lt RS 898825 2 58 33 zz s 244 48 35 y 2 9 gt 8 m fn S 90 2 5 o9 9 2 0 o Bp o 2 23 2 292 lt T lt O 95 On N o o e 8 9 e m E ea 8
7. SUCTION COVER STRAINER ASSEMBLY COVER STRAINER SUCTION FITTING GASKET 25 DOME CLEANING For routine cleaning of the dome use a mild liquid detergent Do not use cleaners containing abra sives alcohol ammonia or other solvents CARE AND MAINTENANCE STEAMPRO STEAM GENERATORS Maintenance of the Steampros includes flushing periodically and visually inspecting for water leaks To drain the units 1 2 Turn OFF power to the unit To gain access to the SteamPro units open the center panel door To do so open the screw cover and remove the screw Unplug power cords from the SteamPro units and disconnectall plumbing Remove the SteamPro units from their mounting Flush the tanks out the drain plug can be removed with an 8 mm hexagonal wrench Reinstall the steam generators Do NOT operate the steam generators without the water supply ON as permanent damage to the generators will occur Turn ON the water supply and check for leaks Close door and reinstall door bolt Turn ON power to the unit l 230V OUTLET I POWER SUPPLY CORD HOT WATER SUPPLY CABLE TIES COLD WATER SUPPLY 3 8 COPPER TUBING FROM 3 8 SUPPLY FITTING FROM STEAM FITTIN ON BATH 26 PRODUCT SPECIFICATIONS ARE SUBJECT CHANGE WITHOUT
8. N s 2 gs 5 8 V 9 o 2 5 z Q 5 8 Nm D t 2 5 3 5 gg Uu o O z 2 5 95 D o 2 S a 2 o X a
9. Pressing Stationary Shower button once activates the shower and pressing a second time deactivates the shower Pressing the OFF button or any other button except steam will turn the shower mode OFF 21 Starting the Hydromassage The J Allure allows you to enjoy the benefits of a real hydromassage The hydromassage is created by the combined action of 8 water jets two sets of four The action of each group of four jets is either alternated or pulsed To start the hydromassage jets press the JETS button once Figure 1 This will activate the jets by alternating the sets of four jets Pressing it a second time will pulse all eight jets Pressing a third time turns the hydromassage OFF While the hydromassage is in either mode the PULSED JETS button may be pushed Pressing this button once will increase the rate of the pulses from a default speed Pressing a second and third time continues to increase the rate of pulsation Pressing a fourth time reverts to the default rate To stop the hydromassage in any mode press the OFF button or any other button Starting the Steam Bath Press the STEAM start button on the display Figure 1 The steam function has a 60 minute cycle after which it turns off automatically The steam bath can be turned off at any time by depressing the OFF button Do NOT operate the steam generators without the water supply ON as permanent damage to the generators will occur Note During steam bath operation keep legs
10. the generators using hose clamps For units with TV insert audio cables cable TV lead fan and TV power cords through the hole in drip shield Plug the power cord into the 230 VAC outlet installed previously as shown in the rough in section DANGER RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a Ground Fault Circuit Interrupter Reinstall hand held shower holder if removed Apply sealant to mounting holes if holder was removed completely 230V OUTLET l POWER SUPPLY CORD HOT WATER SUPPLY HOSE A LAT p LS CABLE TIES COLD WATER SUPPLY HOSE MIXER 3 8 COPPER TUBING FROM 3 8 SUPPLY FITTING CABLE DRIP SHIELD gt ONLY Z T FAN POWER CORD CABLE TV LEAD AND AUDIO CABLES FROM STEAM POWER CORD FOR TV FITTINGS ON BATH UNIT WITH TV SHOWN 12 J Allure TV Installation Units with TV Remove drip shield Connect power cord audio cable antenna cable TV Hook up fan power lines with red to red and black to black wires Tighten cable tie and cut off excess Tighten cable tie with anchor not supplied to the TV power cord It is not necessary to attach anchor to drip shield the cable tie and anchor are used to ensure the TV power cord remains inside drip shield Position the dr
11. to carpet ceiling loss of use etc including its own negligence damages to respecting or resulting from plated parts when chemicals are used in the unit optional equipment not manufactured by the Company supplied by Dealer installer or the Company the unit s prior usage as an operational display or defects that should have been discovered before installation This limited warranty does not include labor transportation or other costs incurred in the removal and or reinstallation of the original unit and or installation of a replacement unit any costs relating to obtaining access for repair or loss of use damage including loss of sales profit or business advantage of any kind under any circumstances Units in commercial use are excluded from any warranty coverage whatsoever Warranty coverage is provided in the United States of America only IMPLIED WARRANTIES implied warranties of merchantability and fitness for a particular purpose are equal in duration with the express warranties set forth herein NOTICE This warranty gives you specific legal rights and you may also have other rights which vary from state to state There are no warranties applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws The Company will not be responsible for any statements or representations made in any form that go beyond are broader than or are inconsistent with any authorized
12. J ALLURE Luxury Bathing and Entertainment System Installation amp Operation Instructions ua WHIRLPOOL mE BATH IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE BEGINNING ASSEMBLY AND INSTALLATION SUMMARY OF PRECAUTIONS Suction cover must be in place at all times to minimize the potential for hair and body entrapment Keep body and hair a minimum of 6 away from suction fitting at all times when the whirlpool system is operating Hair longer than shoulder length should be secured close to the head Other than those built into this unit never operate electrical appliances hairdryer telephone television radio etc inside or within 5 feet of the bath Never leave small children unattended in the bath Do not use oil based bath additives in your whirlpool bath When cleaning your bath do not use abrasive substances which will damage the bath s surface A maximum water temperature of 104 F is recommended Bathing at temperatures above 104 F for prolonged periods can be injurious to health prevent discoloration of the acrylic finish do not fill the bath with water in excess of 140 F The whirlpool system should be purged at least twice a month For your convenience we have developed a plumbing system cleaner Systems Clean specifically for whir
13. M SHIM Wall Cutouts FACE OF FINISHED FINISHED WALL FINISHED WALL J Allure 81 FINISHED WALL 4 MIN ELECTRICAL OUTLET 115 V FOR BATH IN WALL CUTOUT J PLUMBING _ STUD DETAIL 1 Wall Cutouts 38 38 STUD FOR ELECTRICAL OUTLET 230 V FINISHED OOR 3 8 OD COPPER TUBE TO STEAMPRO UNITS FOR CENTER PANEL BATH FOR UNITS WITH TV CABLE TV OUTLET INISHED LL 1x4 NOT FOR SUPPORT DO NOT BRIDGE PERIMETER CENTER PANEL CUTOUT Suggested Rough in Plumbing for Center Panel STUD _ 1 2 NPTF COLD WATER SUPPLY _ HOT WATER SUPPLY 3 1 2 FINISHED FLOOR 4 2 3 4 19 3 4 41 1 2 STUD DETAIL 1 J Allure Skirt Installation It is necessary to mount the skirt shell clips on the factory installed wood blocks located along the underside of the rim Mark hole locations on the blocks using clips as a template for correct hole spacing Then drill a pilot hole 1 2 deep using a 3 32 diameter drill Use caution to avoid drilling through the bath rim Secure the clips to the wooden blocks as shown SCREWS WOOD PROVIDED BLOCK SHELL k SHELL CLIP 1 4 Using a square or level determine the location of the vertical drop from the bath rim at both ends an
14. NOTICE USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT Jacuzzi Whirlpool Bath has obtained applicable code standards listings generally available on a national basis for products of this type Itisthe responsibility ofthe installer owner to determine specific local code compliance priorto installation ofthis product Jacuzzi Whirlpool Bath makes no representation or warranty regarding and will not be responsible for any code compliance JACUZZI WHIRLPOOL BATH Jacuzzi Whirlpool Bath National Headquarters P O Drawer J Walnut Creek CA 94596 925 938 7070 Service Support Call 925 938 7411 01998 Jacuzzi Whirlpool Bath N115000C 12 02 Printed on Recycled Paper Printed in the U S A Jacuzzi Whirlpool Bath Limited Warranty Shower System Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath the Company offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Shower System product unit who purchases the product for personal or single family use user The Company will repair or replace at its option the unit or its equipment in accordance with the following terms and conditions ONE YEAR LIMITED WARRANTY ON SHOWER SYSTEM Our warranty on Shower System products is for one 1 year Our warranty covers the unit and factory installed components e g pump motor against defects in material or workmanship Warranty coverage begins on the date the unit was o
15. RIMETER J Allure Service Access The skirt fits along the front of the bath and is an access panel for servicing Allow a space of at least 8 inches away from the bath for skirt removal To remove the skirt remove the screws at the bottom of the skirt and withdraw the skirt Bath Electrical Connections A separate circuit which must be protected by a Ground Fault Circuit Interrupter GFCI is required Install a duplex outlet not provided to the studwall underneath the bathtub at least 4 inches above the floor CAUTION Operating the motor pump without enough water in the bath can cause leaking and permanent damage to the pump Before power is applied to the installation make sure the switch is in the OFF position to avoid pump damage DANGER RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a Ground Fault Circuit Interrupter FINISHED WALL 3 PRONG PLUG DUPLEX RECEPT Drain Information A drain overflow assembly must be installed on the bath water tested and connected to the sanitary system of the house After opening the carton inspect for damage and verify that the kit is of the proper finish In the Jacuzzi Whirlpool Bath drain overflow kit note that the waste flange strainer overflow cover and cover screws are packaged in a separate package within the kit to protect the trim finish Follow the installation instructions provided with the drain overf
16. Use Date Purchased Purchased From Installed By Serial Number J Allure ELECTRICAL REQUIREMENTS BATH 115 VAC 60 Hz 15 Amp Single Phase Must be GFCI Protected Specifications REQUIRED OPERATING WATER ELECTRICAL FLOOR GALLONAGE SUPPLY PRODUCT REQUIREMENTS DIMENSIONS MOTOR PUMP LOADING BATH SHOWER WEIGHT SHOWER 54 1372 mm L 115 VAC 60 Hz 74 Ib sq ft 70 U S gal ud r min 521 Ib 230 VAC 60 Hz 54 1372 10 Amp 459 9 265 liters 30 65 235 20 Amp 3 Wire Single phase Must be GFCI Protected 3 CLEARANCE TO REMOVE DOME 7 9 1 8 Y 83 3 8 92 1 2 20 1 4 NM Js 15 1 4 72 76 13 3 4 DRAIN OVERFLOW PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 2 m J Allure HARDWARE SKIRT SCREW DRYWALL Lp 8x 2 Quantity 4 SCREW SHEETMETAL 6x 1 2 Quantity 15 Hert CENETER PANEL HEX NUT Quantity 6 SCREW M3 5X9 5 Quantity 6 ttt SCREW COVER Quantity 4 gt 4 4 4 4 4 4 4 4 WALL ANCHOR Quantity 4 FLAT WASHER Quantity 6 SCREW M42X19 Quantity SCREW 8 1 Quantity 4 GLASS ASSEMBLY SCREW 5 9 5 Quantity 4 SCREW M3 9X22 Quantity 8
17. a distance of at least 3 away from the steam jets BATH OPERATION Note These instructions pertain to all bath products manufactured by Jacuzzi Whirlpool Bath Not all features discussed in this instruction pamphlet apply to all baths All baths manufactured by Jacuzzi Whirlpool Bath are designed for fill and drain which means the bath should be drained after each use and filled with fresh water by the next bather This is a health precaution as these baths are not designed to hold water continuously like pools or spas If you want a unit designed to continuously hold water see your Jacuzzi Whirlpool Bath dealer for the complete line of whirlpool spas available Once the bath is installed remove any residue or foreign materials left over from construction Use turpentine or paint thinner to remove stubborn stains paint or tar Other dirt can be cleaned off with a mild liquid detergent on a damp cloth Scrape off plaster with a wooden or plastic edge do not use metal scrapers wire brushes or other metal tools as they will damage the bath s surface Water Level Close the drain and fill the bath until water is at least 2 above the highest jet see water line indicated in the illustration Do not turn on the whirlpool system at any time if the jets are not completely immersed in water Running the whirlpool system when there is insufficient water in the bath could result in water spraying outside the bath area Running the whirlpool system
18. about water content contact us for a copy of the Jacuzzi Water Quality Primer Bath Additives NOTE DO NOT USE OIL OR OIL BASED BATH ADDITIVES If you want to use any kind of bath additive use only a small amount of low foaming powder or crystal sub stance the whirlpool action intensifies the foaming prop erties of soaps The use of certain bath oils bubble baths and bath additives may increase the level of accumulations of bath residue in the whirlpool system If excess accumu lations persist you should discontinue use of these products Suction Cover Strainer Maintenance Clean the suction cover strainer of hair and debris when necessary To do this remove the center screw and detach the square cover Clean the cover by backflush ing debris from the holes Replace the suction cover immediately after cleaning When reinstalling orientthe cover strainer with the small notch at the bottom The gasket must be inserted into the groove of the cover strainer before reinstalling onto the suction fitting CAUTION Keep hair a minimum of 6 inches away from the suction fitting at all times when the whirl pool system is operating Hair longer than shoulder length should be secured close to the head or a bathing cap should be worn Do not operate the whirlpool system with the suction cover removed It is a safety device and must always be in place on the suction fitting to minimize the potential hazard of hair and body entrapment
19. ailure is of the nature or type covered by the warranty the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the problem during the warranty period conclusive evidence e g proof of purchase or installation is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period an authorized independent service person or Company representative has been permitted to inspect the unit during regular business hours within a reasonable time after the problem was reported by the user In order to obtain warranty service consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service Agent Describe the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent call or write Jacuzzi Whirlpool Bath Warranty Service Department P O Drawer J Walnut Creek California 94596 Call 800 288 4002 To obtain warranty replacement for factory installed components or Company supplied options and accessories manufactured and supplied by the Company call or write the above Provide a description of the problem and proof of purchase You will be instructed how to obtain replacements and where to return at your expense the failed component s option s or accessories
20. all the upper guide following the same procedure as used with the lower guide Caulk the top of each fixed panel SCREWS WITH SPACERS 4 UPPER GUIDE SEALANT LOGO N SCREWS 8 j 4 2x19mm LOWER GUIDE REMOVE GASKET J Allure Fixed Panels Installation cont Install the two wall extrusions on the ends of the fixed panel assembly Make sure they are flush against each fixed panel Where the fixed panel assembly will rest on the bath rim apply sealant Position the fixed panel assembly on the bath by inserting the pin into its seat on the lower guide The curve of the fixed panel should match the curve of the bath Lift left side wall through the open doors Insert the 3 bolts welded on the side wall frame into the slotted holes in the center panel frame Place the opposite side of the side wall against the fixed panel frame Make sure the wall extrusion is against the wall Check perpendicularity with a level Mark this wall extrusion position Remove left side wall and repeat the above steps for the right side wall Remove this side wall and fixed panels assembly Using the 3 holes in each extrusion as a guide drill three 15 64 holes into adjacent wall for each side Attach the wall extrusions to the walls with the anchors and 3 5x32mm screws Drill three 7 64 holes into the fixed panel frame using the wall extrusion holes as guides Secure the panel frame t
21. d the center of the bath Locate the center wood block provided at the appropriate distance from the vertical drop centering it lengthwise with relation to the rim of the bath The faces of the side blocks provided will be oriented along a line from the center vertical drop point to the end vertical drop point The blocks can be screwed nailed or adhered with adhesive to the floor Make sure the finished sides of blocks are outward Glue the skirt blade 1 1 2 x 79 3 4 white acrylic strip to the front of the wooden blocks Before attaching skirt locate the CD radio speaker and power connectors coiled under the bath rim Uncoil and connect the speaker and power connectors to the CD radio Also locate the green ground wire and connect to the chassis of the CD radio Slip the skirt up between the rim and the shell clips While holding the skirt at the bottom move it inward toward the bath Lift it up so there is 1 2 gap between the floor and the bottom of the skirt While using shims to hold the skirt up attach the skirt to the skirt blade and wooden blocks with screws through the predrilled holes e SKIRT SHELL CLIP D ax i SKIRT BLADE e i SCREW 77 WITH USING A SQUARE OR LEVEL MARK THE HINGED PERIMETER OF THE BATH ON TH FLOOR CAP NOTE SAME LEVEL SASHES AS FINISHED FLOOR FLOOR 1 2 WOOD BLOCK SPEAKER POWER CONNECTORS FINISHED SIDE OF BLOCK 8 5 8 BATH PE
22. e roller insertion point located at the center of the upper and lower guide Slide the door toward the wall Insert the remaining set of rollers Making sure the bottom rollers are positioned in the bottom guide channel lift them up and tighten the locking nuts Confirm that the door slides smoothly without binding Slide the door toward the wall and repeat the above steps for the other door Adjust lower and upper rollers to align doors where they meet each other when closed Insert the four M5 stud screws and M5 acorn nuts door stops into the threaded holes in the upper guide and tighten them ROLLER INSERTION POINT ROLLER CHANNEL DOOR STOP STUD SCREWS AND ACORN NUTS ROLLER ROLLER INSERTION CHANNEL POINT J Allure Dome Installation Apply gasket to dome as shown below Note there is no gasket on the dome where it rests on the upper guide Then carefully lift the dome and place onto the corner panel side walls and upper guide Bring the edge of the dome in contact with the front part of the upper guide Note the correct position of the dome on the upper guide and side walls as shown below GASKET GASKET SM SM NM NM SIDEWALL DOME GASKET NC T WE wA
23. eported to the seller and the carrier Your freight claims should be filed promptly thereafter Itis the responsibility of the installer building contractor or user to provide access for service The Company is not responsible for any costs relating to obtaining access for repair The user shall bear such costs and if appropriate must seek recovery from the installer Damage occurring to the unit during installation is the responsibility of the installer and or building contractor and damage occurring thereafter is the responsibility of the user Failure of any optional equipment is the sole responsibility of the equipment manufacturer Options and accessories manufactured by the Company are warranted for ninety 90 days from the original date of purchase for parts only The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and or user of these requirements at the time of purchase The Company is not responsible for costs to modify any product to obtain any code approval such as city county or state building codes WARRANTY SERVICE For the customer s benefit the Company maintains a list of independent service personnel to perform required warranty service repairs Such firms are not agents or representatives of the Company and cannot bind the Company by words or conduct The Company will provide the warranty service described above when the following conditions have been met the f
24. ete instructions before beginning installation Each whirlpool bath arrives ready for installation completely equipped with motor pump assembly and plumbing and fittings necessary for whirlpool operation The drain overflow kit and faucet kit must be installed on the bath by the installer Remove the bath from the carton Retain the shipping carton until satisfactory inspection of the product has been made Do not lift the bath by the plumbing at any time handle by the shell or frame only Immediately upon receipt inspect the shell and walls before installing Should inspection reveal any damage or defect in the finish do not install the bath Damage or defect to the finish claimed after the bath is installed is excluded from the warranty Jacuzzi Whirlpool Bath s responsibility for shipping damage ceases upon delivery of the products in good order to the carrier Refer any claims for damage to the carrier For definitions of warranty coverage and limitations refer to the warranty information All bath units are factory tested for proper operation and watertight connections prior to shipping Note Prior to final installation the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered repaired or avoided by following this inspection and testing procedure Save These Instructions for Future
25. ip shield over TV and secure Close the door and make sure the sensor hole on the door aligns with the TV sensor If they do not align adjust the TV position till they are aligned Secure the door Reinstall hand held shower holder if removed Apply sealant to mounting holes if holder was removed completely DRIP SHIELD WIRING TV CONNECTIONS DRIP SHIELD FAN BLACK J TV POWER CORD AUDIO AUDIO CABLE CABLE z TV O HEADPHONE HEADPHONES O O O O O e 14 CABLE TIE IF THE TV HAS BEEN MOVED IN SHIPPING TO CABLE TV LINE LOOSEN ADJUSTMENT SCREWS AND ADJUST THE TV SO IT IS CENTERED IN WINDOW DC POWER INPUT DRIP SHIELD LCD TV ADJUSTMENT BEZEL SCREWS 4 PER DIRECTION POWER AUDIO AND CABLE TV ANT CABLES J Allure Fixed Panels Installation Locate the guide with the gasket This is the lower guide Remove this gasket and install on the top guide Position the lower guide on the two fixed panels while they are resting on the floor in an upside down position Align the predrilled holes in the guide and panels and screw together with screws and spacers 3 5x45mm self threading Attach the external extrusion of the panels to the guide with 4 2x19mm self threading screws The right and left hand fixed panels are identified by the logo Invert the assembled components and inst
26. l vents or acetone on any part of the J Allure Important For units with TV These units are equipped with a fan mounted inside the TV housing Atleast every 2 years have a service technician verify that the fan is operational If the fan is not operating properly discon tinue TV use until fan can be repaired or replaced BATH MAINTENANCE Cleaning the Bath Toclean your bath simply use a mild nonabrasive liquid detergent solution You can protect and restore the gloss to a dulled acrylic surface by applying Meguiar s 10 Mirror Glaze a product specifically designed for use on acrylic finishes If Meguiar s is not available an acrylic polish of equal quality or automotive paste wax is acceptable Never use abrasive household cleaners on any Jacuzzi Whirlpool Bath product Repairs to the Surface Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600 grit wet dry sandpaper Restore the gloss using Meguiar s Mirror Glaze or automotive paste wax Major scratches and gouges which penetrate the acrylic surface will require refinishing Ask your Jacuzzi Whirl pool Bath dealer for special instructions 24 Purging the Whirlpool System NOTE THE WHIRLPOOL SYSTEM SHOULD BE PURGED AT LEAST TWICE A MONTH To remove accumulations of bath residue from the whirlpool system it is recommended that a whirlpool bath be purged at least twice a month For best results however we recommend that yo
27. l vary by locality Jacuzzi Whirlpool Bath is not responsible for the quality of AM reception NOTE In order to hear the TV audio the Pioneer CD Receiver AUX function must be setup to be ON To perform this setting If the unit is on press SOURCE and hold until the unit turns off Press FUNCTION repeatedly until AUX appears in he display Select AUX on and off with A V The status will be displayed AUX ON TV For operation of the TV consult the manual enclosed Note The remote for the TV is not intended to be used inside the shower or in the bath 23 CENTER PANEL MAINTENANCE The hand held shower head is equipped with a screen which must be occasionally cleaned of limestone and other deposits The screen is placed between the flexible hose and the shower head If limestone deposits areonthe jet nozzles the shape of the water jets may be altered Remove and clean the nozzles occasionally Forcefully turn the nozzle counterclockwise until a click is felt Then remove the nozzle and clean it by soaking itin a moderate vinegar and water solution Do not use metal tools such as scissors or screwdrivers etc to clean the nozzle For routine cleaning of plastic surfaces use a mild liquid detergent only Do not use abrasive cleaners alcohol or other solvents Any normal polish can be used to keep acrylic surfaces shiny The glass panels can be cleaned with any glass cleaning product available on the market Do not use abrasives so
28. literature or specifications furnished by the Company Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you RETURN OF WARRANTY CARD The attached pre addressed Warranty Registration Card MUST be filled out by the purchaser within thirty 30 days from purchase and mailed to Jacuzzi Whirlpool Bath in order for this warranty to become effective Jacuzzi Whirlpool Bath P O Drawer J Walnut Creek CA 94596 9885 RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user They are responsible for ensuring the unit is free of defect or damage Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility In the event of a problem the unit must not be installed The Company is not responsible for failures or damage that could have been discovered repaired or avoided by proper inspection and testing prior to installation Damage occurring in transit is the responsibility of the carrier The user or installer MUST open the crates and inspect the unit for damage when it is delivered If damage is discovered it must be reported immediately to the seller and the carrier in writing and an inspection requested Failure of the carrier to respond should be r
29. low kit After the drain is fully installed test for proper drainage If the unit does not drain properly rectify this condition before proceeding with the installation Jacuzzi Whirlpool bath is not responsible for removal and or reinstallation costs NOTE Watertight installation of the drain is the installer s responsibility Drain leakage is excluded from the Jacuzzi Whirlpool Bath warranty of this product Plumbing Pump jets and suction fittings for the whirlpool system are factory plumbed in schedule 40 PVC piping All Jacuzzi Whirlpool Bath products are factory tested for proper operation and watertight connections prior to shipping Before securing the bath to the floor a test for possible water leaks must be made Fill the bath and check for leaks If leaks are detected notify your Jacuzzi Whirlpool Bath Dealer Do not install the unit J Allure Water Supply Consult local authorities for plumbing code requirements in your area IMPORTANT Proper installation of the fill spout plumbing and compliance with local codes are the responsibility of the installer Jacuzzi Whirlpool Bath does not warrant connections of water supply fittings and piping fill systems or drain overflow systems Nor is it responsible for damage to the bath which occurs during installation CAUTION Anonflammable protective barrier must be placed between soldering work and bath unitto prevent damage to the bath Hot and Cold Supply Valve amp Fill S
30. lpool baths For availability call 1 800 288 4002 IMPORTANT SAFETY INSTRUCTIONS WARNING When using this unit basic precautions should always be followed including the following Read and follow all instructions DANGER to reduce the risk of injury do not permit children to use this unit unless they are closely supervised at all times Use this unit only for its intended purpose as described in this manual Do not use attachments not recommended by the manufacturer Never drop or insert any object into any opening Do not operate this unit without the suction cover in place This unit must be connected only to supply circuits that are protected by a ground fault circuit interrupter GFCI Such a GFCI should be provided by the installer and should be tested on a routine basis To test the GFCI push the test button The GFCI should interrupt power Push the reset button Power should be restored If the GFCI fails to operate in this manner there is a ground current flowing indicating a possibility of an electric shock Do not use the unit Disconnectthe unit and have the problem corrected by a qualified electrician before using A pressure wire connector is provided on the exterior of the motor to permit connection of an No 8 AWG 8 4 mm solid copper bonding conductor between this unit and all other electric equipment and exposed metal in the vicinity as needed to comply with local requirements WARNING When using electrical products ba
31. o the wall extrusion with 3 5x9 5mm self threading screws WALL EXTRUSION FIXED PANEL ASSEMBLY FRAME OF CENTER PANEL SEALANT J Allure Side Walls Installation Lift one of the side walls through the open doors Reach under the bath rim and pull up the speaker wires Hook up these wires observing the polarity as directed from the CD player manual Then insert the 3 bolts into the slotted holes in the center panel frame Place the opposite side of the side wall against the wall Make sure the side wall matches the fixed panel Setthe side wall down onto the side of the bath so that the lower frame of the wall is inserted between the bath and the wall Secure the side wall to the center panel frame with lock washers and M6 nuts With the wall flush against the fixed panel drill three 7 64 holes using holes in the wall frame as guides Be careful not to scratch the finish Secure the wall using 3 5x9 5mm self threading screws Repeat the same procedure for the other side wall Close door and secure CENTER PANEL FRAME Sel REAR OF SIDE SPEAKER WALL OBSERVE POLARITY SEE BLAUPUNKT MANUAL J WALL EXTRUSION
32. ody to provide a hydromassage The jets can also be adjusted so that they all point in the same direction clockwise or counterclockwise to circulate the water in a circular motion around the bath causing a total whirlpool effect Water Force The high volume fully adjustable jets can be adjusted to control the force of the water coming into the bath For robust action increase the force of the flow by rotating the jet handles to the left counterclockwise For a more gentle effect rotate the handles to the right clockwise Never run the whirlpool system with all the jets closed Force of Air Two knobs located on the bath serve as controls for the air induction system The intensity of the hydromassage whirlpool action is determined by the amount of air inducted into the water As the amount of air is increased the hydromassage action increases For maximum air induction rotate the control knobs fully counter clockwise to the largest circles For fewer air bubbles decrease the amount of air induction by rotating the control knob clockwise When the knobs are turned to the smallest circles only water is being circulated AIR INDUCTION CONTROLS JETS TURN CLOCKWISE TO TURN COUNTER CLOCKWISE DIRECTIONALLY FULLY REDUCE AIR FLOW TO INCREASE AIR FLOW ADJUSTABLE ADJUSTABLE CD RADIO Note The remote for the CD radio is not intended to be used inside the shower or in the bath Note For units with AM FM radios the quality of AM reception wil
33. pout Locations SIDE WALL APPROX 14 277 RECOMMENDED FILL SPOUT LOCATION RIGHT SIDE WALL HOT amp COLD SUPPLY VALVE LOCATION Clean Up After Installation To avoid dulling and scratching the surface of the bath never use abrasive cleaners A mild liquid detergent and warm water will clean soiled surfaces Remove spilled plaster with a wood or plastic edge Metal tools will scratch the surface Spots left by plaster or grout can be removed if lightly rubbed with detergent on a damp cloth or sponge Paint tar or other difficult stains can be removed with paint thinner turpentine or isopropyl alcohol rubbing alcohol Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600 grit wet dry sandpaper You can restore the glossy finish to the acrylic surface of the bath with a special compound Meguiar s 10 Mirror Glaze If that is not available use automotive rubbing compound followed by an application of automotive paste wax Major scratches and gouges which penetrate the acrylic surface will require refinishing Ask your Jacuzzi Whirlpool Bath dealer for special instructions 10 J Allure Center Panel Installation Connect the fixed male end of the flexible supply lines to the female supply connections in the wall cutout Position the center panel frame in the corner of the bath with the mounting tab
34. riginally purchased by the user NINETY DAY PARTS ONLY LIMITED WARRANTY ON OPTIONS AND ACCESSORIES Our warranty on options and accessories manufactured by the Company is for ninety 90 days for parts only Our warranty covers options and accessories manufactured by the Company e g fill spout kits trim kits skirts against defects of material or workmanship Warranty coverage begins on the date the option or accessory was originally purchased by the user WARRANTY LIMITATIONS Our warranty does not cover defects damage or failure caused by the common carrier installer user or other person or resulting from without limitation any of the following careless handling lifting unit by plumbing abrading finish etc modification of any type for any reason including modification to meet local codes improper installation including installation not in accordance with instructions and specifications provided with the unit connections supplied by the installer of the equipment improper voltage supply or unauthorized electrical modification misuse incorrect operation or lack of proper routine maintenance operation of the unit without specified minimum amount of water or at inappropriate water temperature use of abrasive or improper cleaners or acts of God such as lightning floods earthquakes etc In addition THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause e g water damage
35. s between the edge of the bath and wall To open the service door remove the screw cover below the mixer handle and unscrew the exposed screw To allow the center panel doorto be opened wider it may be necessary to remove the hand held shower holder as shown below Open the door Unscrew the M6 bolt and install the two brackets Check the plumbness with the two brackets touching the wall If necessary adjust the nut till the center panel is perpendicular to the shell deck Using the holes in the brackets as a guide drill two 3 16 holes Secure the frame to the wall using the wall anchors and screws 8x1 Again check the plumbness and make sure the nuts are tight 29 CENTER PANEL DOOR 29 HAND HELD SHOWER p SCREW HOLDER COVER COVER CENTER PANEL FRAME MOUNTING TAB 6 BOLT BRACKET WALL ANCHOR 2 PLACES J Allure Center Panel Installation cont Connect the ends of the flexible supply lines with adaptors to the hot and cold connections of the mixer The steam lines are to be routed in such a way that they travel up from the steam generators and down to the steam heads Using cable ties tie up the steam lines so there are no kinks or low spots that may trap water Do NOT operate the steam generators without the water supply ON as permanent damage to the generators will occur Connect the steam lines to
36. sic precautions should always be followed including the following DANGER RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a ground fault circuit interrupter Grounding is required This unit should be installed and grounded by a qualified electrician Install to permit access for servicing Note This is a professional grade product A good knowledge of construction techniques plumbing and electrical installation according to codes are required for proper installation and user satisfaction We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products Our warranty does not cover improper installation related problems Options Trim Kits P412827 Chrome P412898 Brushed Chrome P412828 Gold P412829 Bright Brass P413827 Chrome P413898 Brushed Chrome P413828 Gold P413829 Bright Brass Drain Kits 8730827 Chrome 8730898 Brushed Chrome 8730828 Gold 8730829 Bright Brass Contents Specifications 2 Hardware 3 Framing and Support 4 Rough in Reference 5 7 Skirt Installation and Service Access 8 9 Electrical 9 Drain Information and Plumbing 9 Water Supply 10 Center Panel Installation 11 12 TV Installation For units with TV 13 Fixed Glass Panels Installation 14 15 Side Wall Installation 16 Caulking 17 18 Sliding Doors Installation 19 Dome Installation 20 Operation 21 23 Maintenance 24 26 Warranty 29 30 Important Read compl
37. u purge your whirlpool bath after each use using our exclusive two part plum bing system cleaner made specifically for whirlpool baths Systems Clean is available through an autho rized Jacuzzi Whirlpool Bath Distributor or by calling us direct at 1 800 288 4002 Instructions for use Imme diately after bathing and exiting the whirlpool bath leave the bath water in the tub and add hot water if necessary so the water is at least 2 above the highest jet Turn on the unit without the aerator Pour the contents of the Systems Clean Packet 1 taking care not to get the material on yourself into the bath near the intake for the circulation pump Repeat same process with Systems Clean Packet 2 It is important to use Packet 1 before Packet 2 to avoid a strong odor Run the bath for 5 to 10 minutes Drain completely and rinse any residue If you have followed the standard purging instructions above and still have an excess accumulation of bath residue and desire an alternative cleaning mechanism werecommend SUPER SYSTEMS CLEAN PLUS manu factured by Stearns Packaging to rectify this condition This may be obtained by contacting us at 800 288 4002 Itis recommended that you follow the instructions provided by the manufacturer with the product Re peated use may be necessary SUPER SYSTEMS CLEAN PLUS does not replace the necessity to regu larly purge your whirlpool system with Systems Clean as recommended For additional information
38. without water will damage the recirculating pump Magic Touch Whirlpool Switch The Magic Touch whirlpool ON OFF switch conveniently located on the bath allows you to turn the whirlpool system on and off while in the bath Simply push down on the switch button to turn on the whirlpool system To turn the system off push down on the button again If your bath has an optional Jacuzzi Whirlpool Bath wall mounted timer set it for the amount of time you wish the whirlpool to operate Note when you desire less than 10 minutes of whirlpool action it is necessary to turn the timer knob clockwise past the number 10 and then back to the desired amount If the whirlpool action does not begin when the timer is correctly set it is necessary to push the Magic Touch switch button FILL TO AT LEAST 2 ABOVE HIGHEST JET MAGIC TOUCH SWITCH lt gt DEPRESS CENTER ON OFF 22 Controlling Whirlpool Action The whirlpool action in your bath is influenced by three factors direction of flow force of water and force of air All baths manufactured by Jacuzzi Whirlpool Bath are equipped with fully adjustable PowerPro jets which are adjustable for all three factors Some baths have additional directionally adjustable jets which can be adjusted for direction and flow of air only Direction To change the direction of the water flow swivel the jet nozzle to the desired angle The jets can be directed individually toward any location on your b
Download Pdf Manuals
Related Search