Insignia NS-32L550A11 Flat Panel Television User Manual
Contents
1. Storage Temp 25 C to 65 C 13 F to 149 F Humidity 5 to 95 non condensing Altitude 0 to 10 000 feet Warranty Lifetime MTBF is estimated using the predictability method This method is based on MIL 217F at 25 C ambient temperature typical enclosure heat rise of 10 C with nominal operating conditions and parameters Installation and configuration specific MTBF estimates are available upon request Contact Technical Support Mfanufacturer s rated ambient temperature CAUTION Copper based media ports e g Twisted Pair TP Ethernet USB RS232 RS422 RS485 DS1 DS3 Video Coax etc are intended to be connected to intra building inside plant link segments that are not subject to lightening transients or power faults Copper based media ports e g Twisted Pair TP Ethernet USB RS232 RS422 RS485 DS1 DS3 Video Coax etc are NOT to be connected to inter building outside plant link segments that are subject to lightening transients or power faults Failure to observe this caution could result in damage to equipment techsupport transition com Click the Transition Now link for a live Web chat 11 M GE PSW xxX 01 Technical Specifications Continued Copper based media ports e g Twisted Pair TP Ethernet USB RS232 RS422 RS485 DS1 DS3 Video Coax etc are intended to be connected to intra building inside plant link segments that are not subject to lightening transients or2. s and duplex capabilities full or half to the other device and negotiates the best mode of operation Auto Negotiation allows quick and easy installation because the optimal link is established automatically In a scenario where an auto negotiation device is linked to a non negotiating device the negotiating device via parallel detection recognizes the speed of that second device then establishes the best operating speed 0 100 100Mbs at half duplex AutoCross The AutoCross feature allows using either straight through MDI or crossover MDI X copper cables when connecting to 10Base T or 100Base TX devices AutoCross determines the characteristics of the connection and automatically configures the device to link up regardless of the copper cable configuration MDI or MDI X Link Pass Through The Link Pass Through feature illustrated below allows the media converter to monitor both the fiber and copper RX receive ports for loss of signal In the event of an RX signal loss 1 the media converter will automatically disable the TX transmit signal 2 thus passing through the link loss 3 The far end device is automatically notified of the link loss 4 which prevents the loss of valuable data unknowingly transmitted over an invalid link media converter A media converter B disables the fiber TX link loses the fiber RX link Near End i i l Far End Device Ks Converter A Converter B is Device original fau
3. 512 BT the path is good For more information on the 512 Bit Rule see the white paper titled Collision Domains on the Transition Networks website at www transition com Back pressure Back pressure is used in half duplex mode It ensures the retransmission of incoming packets when a port using half duplex is temporarily unable to receive incoming frames Flow Control The process of adjusting the flow of data from one device to another ensures that the receiving device can handle all the incoming data This is particularly important where the sending device is capable of transmitting data much faster than the receiving device can accept it Distance extension The M GE PSW xX 01 media converters can segment one 1 10Base T copper Ethernet 100Base T copper fast Ethernet or 1000Base T copper Gigabit Ethernet and one 1 1000 Base X fiber Fast Ethernet collision domain In a half duplex Ethernet or Fast Ethernet environment the M GE PSW xX 01 media converters extend network distances by segmenting collision domains so that the 512 Bit Rule applies separately to each collision domain In a full duplex Ethernet or Fast Ethernet environment the M GE PSW xX 01 media converters extend network distances to the physical cable limitations imposed by the selected twisted pair copper fiber cables Rate conversion The M GE PSW xX 01 media converters allow the following connections e 10Mb s devices on a 10Base T legacy copper netw
4. TT eer User s Guide M GE PSW SX 01 M GE PSW LX 01 Stand Alone Media Converters e Copper to Fiber e 10 100 1000Base T to 1000Base X The miniature plug and play M GE PSW xX 01 2 port Ethernet Fast Ethernet bridging media converters allow integrating fiber optic cable to 10 100 1000 Unshielded Twisted Pair UTP environments while providing a space saving alternative to traditional sized media converters M GE PSW xX 01 Auto Negotiation AutoCross Far End Fault FEF Part Number Copper Port Fiber Optic Port 10 100 1000Base T 1000Base FX M GE PSW SX 01 SC RJ 45 SX 850 nm multimode 62 5 125 100 m 328 ft 200m 722 ft 50 125 550m 1 805 ft M GE PSW LX 01 SC RJ 45 LX 1310 nm single mode 100 m 328 ft 10 km 2 1 miles Typical maximum cable distance actual distance is dependent upon the physical characteristics of the network NStANUON s soaa ee Seen cas 2 OPETAN e eea aor oe Bix 6 Cable Specifications 10 Technical Specifications 11 Troubleshooting 12 CONOCES sumasa ee a 13 Declaration of Conformity 14 Compliance Information 15 M GE PSW xxX 01 Installation Copper and fiber ports The illustration below shows the front panel of the M GE PSW xX 01 media converters Front Panel TP Link Active Fiber Link Activity Copper Port Fiber Port Power ON LED Electrostatic Discharge ESD Always observe the
5. d connection is made techsupport transition com Click the Transition Now link for a live Web chat 3 M GE PSW xxX 01 Installation Continued Connect the twisted pair copper cable The AutoCross feature allows either MDI straight through or MDI X crossover cable connections to be configured automatically according to network conditions 1 Locate or build IEEE 803 2 compliant 10 100 1000Base T cables with RJ 45 connectors installed at both ends 2 Connect the RJ 45 connector at one end of the cable to the RJ 45 port on the M GE PSW xX 01 media converter 3 Connect the RJ 45 connector at the other end of the cable to the RJ 45 port on the other device switch workstation etc al RJ 45 port RJ 45 port on the media on the other device converter switch work station etc Note With AutoCross permanently enabled the link LED only lights when a valid end to end connection is made Installation Continued Powering the media converter The M GE PSW xX 01 media converter is powered by using a DC power adapter through the barrel connector on its rear panel as shown below M GE PSW xX 01 Back Panel Power Back Panel Barrel Connector 5 28 VDC Power adapter AC power 1 Connect the barrel connector of the power adapter to the media converter s power port located on the back panel of the media converter 2 Connect the power adapter plug to AC power Ve
6. e public telephone network Der Anschluss dieses Ger tes an ein offentlickes Telekommunikationsnetz in den EG Mitgliedstaaten verstdsst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91 263 EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten ber Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformitat 14 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat 15 M GE PSW xxX 01 Trademark Notice All trademarks and registered trademarks are the property of their respective owners Copyright Restrictions 2001 2005 Transition Networks All rights reserved No part of this work may be reproduced or used in any form or by any means graphic electronic or mechanical without written permission from Transition Networks 16 Printed in the U S A 33398 A
7. fg Transition Networks 10900 Red Circle Drive MinnetonkaMN 55343 U S A Model M GE PSW xX 01 Series Media Converters Part Number s M GE PSW LX 01 and M GE PSW SX 01 Regulation EMC Directive 89 336 EEC Purpose To declare that the M GE PSW xX 01 to which this declaration refers is in conformity with the following standards EN 55022 1994 A1 1995 A2 1997 EN 55024 1998 A1 2001 A2 2003 I the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s oh Sar et ae J January 2008 Stephen Anderson Vice President of Engineering Date Compliance Information CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense Canadian Regulations This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus
8. following ESD precautions when installing or handing the M GE PSW xX 01 media converter e Do not remove the converter from its protective packaging until you are ready to install it e Wear an ESD wrist grounding strap before handling any module or component If you do not have a wrist strap maintain grounded contact with the system unit throughout any procedure requiring ESD protection Installation Continued Connect the fiber cable Full duplex always ON is on the fiber side only therefore the 512 Bit Rule does not apply The cable lengths are constrained by the cable requirement il Locate or build IEEE 803 2 compliant 1000Base X fiber cable with male two stranded TX to RX connectors installed at both ends Connect the fiber cable to the M GE PSW xX 01 media converters as follows Connect the male TX cable connector to the female TX port Connect the male RX cable connector to the female RX port Connect the fiber cable to the other device another media converter hub etc as follows Connect the male TX cable connector to the female RX port Connect the male RX cable connector to the female TX port Connect fiber cable Connect fiber cable to media converter to other device as shown media converter hub etc as shown a 2 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours Note With AutoCross permanently enabled the link LED only lights when a valid end to en
9. llowing e Asa link pass through device both copper and fiber cables must be installed before the LEDs will light 2 Are the TX and FX Link ACT LEDs illuminated on the RJ 45 port NO e Check the copper cables for proper connection e Check the fiber cables for proper connection e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 12 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours Contact Us Technical Support Technical support is available 24 hours a day US and Canada 1 800 260 1312 International 00 1 952 941 7600 Transition Now Chat live via the Web with Transition Networks Technical Support Log onto www transition com and click the Transition Now link Web Based Seminars Transition Networks provides seminars via live web based training Log onto www transition com and click the Learning Center link E Mail Ask a question anytime by sending an e mail to our technical support staff techsupport transition com Address Transition Networks 10900 Red Circle Drive Minnetonka MN 55343 U S A telephone 952 941 7600 toll free 800 526 9267 fax 952 941 2322 techsupport transition com Click the Transition Now link for a live Web chat 13 M GE PSW xxX 01 Declaration of Conformity TRANSITION Declaration of Conformity Name of M
10. lt media converter B on the copper link disables the copper link Note Both copper and fiber cables must be installed before the LEDs will light Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat 7 M GE PSW xxX 01 Operation Continued Product features continued Operation Continued Product features continued Automatic link restoration The media converter will automatically re establish the link when connected to switches if the link is lost even with Auto Negotiation and Link Pass through both directions enabled Full Duplex flow control In a full duplex network maximum cable lengths are determined by the type of cables used see page front cover for M GE PSW xX 01 cable specifications The 512 Bit Rule does not apply in a full duplex network Note Full duplex is ON permanently for the fiber port only Half Duplex flow control 572 Bit Rule In a half duplex network the maximum cable lengths are determined by the round trip delay limitations of each Fast Ethernet collision domain A collision domain is the longest path between any two terminal devices e g a terminal switch or router The 512 Bit Rule determines the maximum length of cable permitted by calculating the round trip delay in bit times BT of a particular collision domain If the result is less than or equal to
11. ork to 1000Mb s devices on a 1000Base SX LX Gigabit Ethernet fiber network e 100Mb s devices on a 100Base T legacy copper network to 1000Mb s devices on a 1000Base SX LX Gigabit Ethernet fiber network Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat M GE PSW xxX 01 Cable Specifications The physical characteristics must meet or exceed IEEE 802 3 specifications Fiber cable Bit Error Rate lt 10 9 single mode fiber recommended 9 um Multimode fiber recommended 62 5 125 um Multimode fiber optional 100 140 85 140 50 125 um M GE PSW SX 01 SC 850nm multimode Fiber Optic Transmitter Power min 10 0 dBm max 4 0 dBm Fiber Optic Receiver Sensitivity min 17 0 dBm max 0 0 dBm Link Budget 7 0 dB M GE PSW LX 01 SC 1310 nm single mode Fiber optic Transmitter Power min 9 5 dBm max 3 0 dBm Fiber optic Receiver Sensitivity min 20 0 dBm max 3 0 dBm Link Budget 10 5 dB The fiber optic transmitters on this device meet Class I Laser safety requirements per IEC 825 CDRH standards and comply with 21 CFR1040 10 and 21CFR1040 11 Copper cable Category 5 and Category 5e minimum requirement Gauge 24 to 22 AWG Attenuation 22 0 dB 100m 100 MHz Maximum Cable Distance 100 meters e Straight through or crossover twisted pair cable may be used e Shielded STP or unshielded UTP twisted
12. pair cable may be used e Pins 1 amp 2 and 3 amp 6 are the two active pairs in an Ethernet network e All four pairs are used in a gigabit Ethernet network e Use only dedicated wire pairs for the active pins e g blue white amp white blue orange white amp white orange etc e Do not use flat or silver satin wire Straight Through Cable Crossover Cable 1 1 1 1 Twisted Pair 1 2 2 Twisted Pair 1 2 2 Twisted Pair 2 3 3 Twisted Pair 2 3 3 m 6 a CAT5e Gigbit Ethernet Straight Through Cable Twisted Pair 1 Twisted Pair 2 Twisted Pair 3 Twisted Pair 4 10 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours Technical Specifications For use with Transition Networks Model M GE PSW xX 01 converters Standards IEEE 802 3 2000 Data rate 10 Mb s 100 Mb s 1000 Mb s Dimensions 1 8 W x 3 35 D x 0 85 H 45 7 x 85 1 x 21 6 mm Weight 3 15 oz 127 5 g approximately MTBF 24 466 hours MIL217F 2 V5 0 MIL HDBD 217F 100 130 hours Bellcore7 V5 0 Packet size Memory 9256K bytes MAC addresses 8K Maximum packet size 1632 bytes untagged 1628 bytes tagged Power sources Unit will accept 5 to 28 VDC Barrel connector Wall Mount AC Adapter 400mA at 12VDC The external power supply provided with this product is UL listed by the power supply s manufacturer Power consumption 262mA 12VDC 3 15 watts Environment Trira 0 C to 50 C 32 F to 122 F
13. power faults Copper based media ports e g Twisted Pair TP Ethernet USB RS232 RS422 RS485 DS1 DS3 Video Coax etc are NOT to be connected to inter building outside plant link segments that are subject to lightening transients or power faults The product is certified by the manufacturer to comply with DHHS Rule 21 CFR Subchapter J applicable at the date of manufacture WARNING Visible and invisible laser radiation when open Do not stare into the beam or view directly with optical instruments Failure to observe this warning could result in an eye injury or blindness WARNING Use of controls adjustments or the performance of procedures other than those specified herein could result in hazardous radiation exposure The information in this user s guide is subject to change For the most up to date information view the user s guide on line at www transition com Troubleshooting If the media converter fails isolate and correct the failure by determining the answers to the following questions and then taking the indicated action l Is the power LED illuminated and did the TX and FX LEDs turn ON then turn OFF NO Is the power adapter the proper type of voltage and cycle frequency for the AC outlet e Is the power adapter properly installed in the media converter and in the outlet e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e Proceed to step 2 Note the fo
14. rify that the media converter is powered up by observing the illuminated LED power indicator light on the front panel DC power Consult the user s guide for the Transition Networks SPS 1872 SA DC external power supply for powering the media converter 4 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat M GE PSW xxX 01 Operation Status LEDs Use the LEDs to monitor the status of the media converter Front Panel TP Link Act LED Fiber Link Act LED Power ON LED LED states are as follows Fiber Link Act LED Green ON Link fiber Flashing Activity TP Link Act LED Green ON Link copper Flashing Activity Power LED Green ON Connected to power Operation Continued Product features Congestion reduction The M GE PSW xX 01 media converters do not forward collision signals or error packets from one collision domain to another resulting in improvements in baseline network performance In addition the media converter filters packets destined for local devices which reduces network congestion also Auto Negotiation The Auto Negotiation feature is ON permanently for the M GE PSW xX 01 media converters Auto Negotiation allows the media converter to configure itself automatically to achieve the best possible mode of operation over a link It broadcasts speed 10 100 1000 Mb
15. set out on the radio interference regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la Class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada European Regulations Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Achtung Dieses ist ein Ger t der Funkst6rgrenzwertklasse A In Wohnbereichen k nnen bei Betrieb dieses Ger tes Rundfunkst rungen auftreten In diesem Fall ist der Benutzer f r Gegenma nahmen verantwortlich Attention Ceci est un produit de Classe A Dans un environment domestique ce produit risque de cr er des interf rences radio lectriques il appartiendra alors l utilsateur de prende les measures sp cifiques appropri es In accordance with European Union Directive 2002 96 EC of the European Parliament and of the Council of 27 January 2003 Transition Networks will accept post usage returns of this product for proper disposal The contact information for this activity can be found in the Contact Us portion of this E ocument PUBLIC TELEPHONE NETWORK Failure to observe this caution could result gt CAUTION RJ connectors are NOT INTENDED FOR CONNECTION TO THE in damage to th
Download Pdf Manuals
Related Search