IBM 2251 Computer Hardware User Manual
Contents
1. Lithium battery notice CAUTION Danger of explosion if battery is incorrectly replaced When replacing the battery use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer The battery contains lithium and can explode if not properly used handled or disposed of Do not e Throw or immerse into water e Heat to more than 100 C 212 F Repair or disassemble Dispose of the battery as required by local ordinances or regulations ATTENTION Danger d explosion en cas de remplacement incorrect de la batterie Remplacer uniquement par une batterie IBM de type ou d un type quivalent recommand par le fabricant La batterie contient du lithium et peut exploser en cas de mauvaise utilisation de mauvaise manipulation ou de mise au rebut inappropri e Ne pas Lancer ou plonger dans l eau e Chauffer a plus de 100 C 212 F e R parer ou desassembler Mettre au rebut les batteries usag es conform ment aux r glements locaux Modem safety information To reduce the risk of fire electrical shock or injury when using telephone equipment always follow basic safety precautions such as Never install telephone wiring during a lightning storm Vi User Guide Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations Never touch uninsulated telephone wires or terminals unless the telephone line has been disc2. 36 User Guide Appendix C System address maps The following charts represent how the hard disk stores different types of information Address ranges and byte sizes are approximate System memory map The first 640 KB of system board RAM is mapped starting at address hex 00000000 A 256 byte area and a 1 KB area of this RAM are reserved for BIOS data Memory can be mapped differently if POST detects an error Address range Address range hex Size Description decimal 0K 512 KB 00000 7FFFF 512 KB Conventional 512 K 639 KB 80000 9FBFF 127 KB Extended conventional 639 K 640 KB 9FC00 9FFFF 1 KB Extended BIOS data 640 K 767 KB A0000 BFFFF 128 KB Dynamic video memory display cache 768 K 800 KB C0000 C7FFF 32 KB Video ROM BIOS shadowed 800 K 896 KB C8000 DFFFF 96 KB PCI space available to adapter ROMs 896 K 1 MB E0000 FFFFF 128 KB System ROM BIOS main memory shadowed 1MB 16MB 1000000 FFFFFF 15 MB PCI space 16 MB 4096 MB 10000000 FFDFFFFF 4080 MB PCI space positive decode FFFEO000 FFFFFFFF 128 KB System ROM BIOS I O address map The following table lists resource assignments for the I O address map Any addresses that are not shown are reserved Copyright IBM Corp 2002 Address range hex Size bytes Description 0000 000F 16 DMA 1 0010 001F 16 General I O locat
3. EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication IBM may make improvements and or changes in the product s and or the program s described in this publication at any time without notice IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication to non IBM Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this IBM product and use of those Web sites is at your own risk Television output notice The following notice applies to models that have the factory installed television output feature This product incorporates copyright protection technology that is protected by method claims of certain U S patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology m
4. When you attach an external audio device a cable is connected between the audio line out connector of the device and the audio line in connector of the computer Used to attach a microphone to your computer when you want to record voice or other sounds on the hard disk if you use speech recognition software Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http www ibm com pc support on the World Wide Web Installation instructions are provided in README files with the device driver files Chapter 1 Installing options 9 Removing the cover 10 User Guide r Important Read Safety Information on page v and Handling static sensitive devices before removing the cover To remove the cover 1 Shut down your operating system remove any media diskettes CDs or tapes from the drives and turn off all attached devices and the computer 2 Unplug all power cords from electrical outlets 3 Disconnect all cables attached to the computer This includes power cords input output I O cables and any other cables that are connected to the computer 4 Remove the two screws at the rear of the left side cover and slide the cover to the rear to remove Locating components The following illustration will help you locate the various components in your computer Microprocessor and heat si
5. or reconfiguration of this product during an electrical storm Connect all power cords to a properly wired and grounded electrical outlet Connect to properly wired outlets any equipment that will be attached to this product When possible use one hand only to connect or disconnect signal cables Never turn on any equipment when there is evidence of fire water or structural damage Disconnect the attached power cords telecommunications systems networks and modems before you open the device covers unless instructed otherwise in the installation and configuration procedures Connect and disconnect cables as described in the following table when installing moving or opening covers on this product or attached devices To connect To disconnect 1 Turn everything OFF 1 Turn everything OFF 2 First attach all cables to devices 2 First remove power cords from outlet 3 Attach signal cables to connectors 3 Remove signal cables from connectors 4 Attach power cords to outlet 4 Remove all cables from devices 5 Turn device ON DANGER Le courant lectrique provenant de l alimentation du t l phone et des c bles de transmission peut pr senter un danger Pour viter tout risque de choc lectrique Copyright IBM Corp 2002 Ne manipulez aucun c ble et n effectuez aucune op ration d installation d entretien ou de reconfiguration de ce produit au cours d un orage Branchez tous les cordons
6. T8 Perform Local Analog Loopback Test and Self Test amp V amp VO Displays Active and Stored Profiles amp V1 Display Last Connection Statistics amp W_ amp WO Stores the active profile as Profile 0 amp W1 Stores the active profile as Profile 1 E_ E0 Disable auto retrain E1 Enable auto retrain MS Displays the current Select Modulation settings MS Displays a list of supported Select Modulation options Appendix B Manual modem commands 33 Command Function MS a b c e f Select modulation where a 0 1 2 3 9 10 11 12 56 64 69 b 0 1 c 300 56000 d 300 56000 e 0 1 and f 0 1 A b c d e f default 12 1 300 56000 0 0 Parameter a specifies the modulation protocol desired where 0 V 21 1 V 22 2 V 22bis 3 V 23 9 V 32 10 V 32bis 11 V 34 12 V 90 K56Flex V 34 56 K 56Flex V 90 V 34 64 Bell 103 and 69 Bell 212 Parameter b specifies automode operations where 0 automode disabled 1 automode enabled with V 8 V 32 Annex A Parameter c specifies the minimum connection data rate 300 56000 Parameter d specifies the maximum connection rate 300 56000 Parameter e specifies the codec type 0 Law and 1 A Law Parameter f specifies robbed bit signaling detection 0 detection disabled 1 detection enabled MNP V 42 V 42bis V 44 commands Command Function C_ CO Disable MNP Class 5 and V 42bis data compression C1 Enable MNP Class 5 data comp
7. V ac Input frequency range 47 63 Hz Voltage switch setting 230 V ac Input kilovolt amperes kVA approximate Minimum configuration as shipped 0 08 kVA Maximum configuration 0 22 KVA Note Power consumption and heat output vary depending on the number and type of optional features installed and the power management optional features in use Heat output approximate in British thermal units Btu per hour Minimum configuration 257 Btu hr 75 watts Maximum configuration 616 Btu hr 180 watts Airflow Approximately 0 48 cubic meters every minute 17 cubic feet every minute maximum Acoustical noise emission values Average sound pressure levels At operator position Idle 32 dBA Operating 39 dBA At bystander position 1 meter 3 3 ft Idle 31 dBA Operating 35 dBA Declared upper limit sound power levels Idle 4 5 bels Operating 5 0 bels Note These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute ANSI S12 10 and ISO 7779 and are reported in accordance with ISO 9296 Actual sound pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources The declared sound power levels indicate an upper limit below which a large number of computers will operate Note The computer is classified as a Class A or Class B digital device See the Quick Referen
8. cable and an integrated cable lock You can also install a padlock to secure the cover Make sure the security cable does not interfere with other computer cables See Access IBM for more security information Refer to the following illustration to identify these security features Chapter 1 Installing options 19 ag 2 g amp CED A QED os Uh Mh ES Padlock loop H Integrated cable lock Rope clip What to do next Changing the battery 20 User Guide Your computer has a special type of memory that maintains the date time and settings for built in features such as parallel port assignments configuration A battery keeps this information active when you turn off the computer The battery normally requires no charging or maintenance throughout its life however no battery lasts forever If the battery fails the date time and configuration information including passwords are lost An error message is displayed when you turn on the computer Refer to Lithium battery notice on page vil for information about replacing and disposing of the battery To change the battery 1 Turn off the computer and all attached devices To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 21 2 Unplug the power cord and remove the cover S
9. d alimentation sur un socle de prise de courant correctement c bl et mis la terre Branchez sur des socles de prise de courant correctement c bl s tout quipement connect ce produit Lorsque cela est possible n utilisez qu une seule main pour connecter ou d connecter les c bles d interface Ne mettez jamais un quipement sous tension en cas d incendie ou d inondation ou en pr sence de dommages mat riels Avant de retirer les carters de l unit mettez celle ci hors tension et deconnectez ses cordons d alimentation ainsi que les c bles qui la relient aux r seaux aux syst mes de t lecommunication et aux modems sauf instruction contraire mentionn e dans les proc dures d installation et de configuration Lorsque vous installez que vous deplacez ou que vous manipulez le present produit ou des p riph riques qui lui sont raccord s reportez vous aux instructions ci dessous pour connecter et d connecter les diff rents cordons Connexion D connexion 1 Mettez les unit s hors tension 1 Mettez les unit s hors tension 2 Commencez par brancher tous les 2 D branchez les cordons d alimentation cordons sur les unit s des prises 3 Branchez les c bles d interface sur des 3 D branchez les c bles d interface des connecteurs connecteurs 4 Branchez les cordons d alimentation sur 4 D branchez tous les c bles des unit s des prises 5 Mettez les unit s sous tension
10. drive in bay 1 e A3 5 inch diskette disk drive in bay 3 e A 3 5 inch hard drive in bay 4 Any bay that does not have a drive installed has a static shield and bay panel installed The following illustration shows the locations of the drive bays The following table describes some of the drives you can install in each bay and their height requirements Bay 1 Maximum height 43 0 mm 1 7 in CD ROM drive or DVD ROM drive preinstalled in some models 5 25 inch hard disk drive A Bay 2 Maximum height 43 0 mm 1 7 in 5 25 inch hard disk drive 3 5 inch hard disk drive requires a mounting bracket CD ROM drive DVD ROM drive Bay 3 Maximum height 25 8 mm 1 0 in 3 5 inch diskette drive preinstalled E Bay 4 Maximum height 25 8 mm 1 0 in 3 5 inch hard disk drive Notes 1 Drives that are greater than 43 0 mm 1 7 in high cannot be installed 2 Install removable media tape or CD drives in the accessible bays bay 1 or 2 Installing a drive To install an internal drive follow these steps 1 2 5 Remove the cover See Removing the cover on page 10 If your computer has a CD ROM drive or DVD ROM drive you might need to remove the signal and power cables from the drive Remove the bay panel from the drive bay by inserting a flat blade screwdriver at the end and gently prying it loose Remove the metal shield from the drive bay by inserting a flat blade screwdriver into one of the slots
11. memory connector sequentially starting at DIMM connector 1 Use 2 5 V 184 pin 266MHz double data rate synchronous dynamic random access memory DDR SDRAM Use 128 MB 256 MB 512 MB or 1 0 GB when available DIMMs in any combination e DIMMs are 38 1 mm 1 5 inches in height Note Only DDR SDRAM DIMMs can be used To install a DIMM 1 Remove the cover See Removing the cover on page 10 2 You might have to remove an adapter to gain access to the DIMM slots See Installing adapters on page 14 3 To locate the DIMM connectors See Identifying parts on the system board on page 11 4 Open the retaining clips 5 Make sure the notches in the DIMM align with the tabs on the connector Push or insert the DIMM straight down into the connector until the retaining clips close m What to do next Replace any adapters that were removed To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 21 Chapter 1 Installing options 13 Installing adapters This section provides information and instructions for installing and removing adapters Your computer has three expansion slots for PCI adapters You can install an adapter up to 228 mm 9 inches long To install an adapter 1 Remove the cover See Removing the cover on pa
12. press Enter Click NetVista and NetVista Thin Client Click NetVista Personal Computer Click Downloadable files Under Select your product choose your machine type and click Go In Downloadable file by category click BIOS Under Downloadable files BIOS by date click your machine type Scroll down and look for the txt file that has instructions for Flash BIOS update from the operating system Click the txt file one 0 D Copyright IBM Corp 2002 29 10 Print these instructions This is very important since they are not on the screen after the download begins From your browser click Back to return to the list of files Carefully follow the printed instructions to download extract and install the update Recovering from a POST BIOS update failure 30 User Guide If power to your computer is interrupted while POST BIOS is being updated flash update your computer might not restart correctly If this happens perform the following procedure to recover 1 2 3 4 O 10 11 12 13 14 15 16 Turn off the computer and any attached devices such as printers monitors and external drives Unplug all power cords from electrical outlets and remove the cover See Removing the cover on page 10 Locate the Clear CMOS Recovery jumper on the system board See Identifying parts on the system board on page 11 If necessary refer to Installing adapters to remove any ad
13. system configuration Diskette Drive Access When this feature is set to Disable the diskette drive cannot be accessed Diskette Write Protect When this feature is set to Enable all diskettes are treated as if they are write protected To set Security Profile by Device do the following 1 Start the IBM Setup Utility program see Starting the IBM Setup Utility program on page 23 ogram on page 25 From the IBM Setup Utility program menu select Security Select Security Profile by Device Select the desired devices and settings and press Enter u Bon Return to the IBM Setup Utility program menu and select Exit and then Save Settings Selecting a startup device If your computer does not start up boot from a device such as the CD ROM diskette or hard disk as expected use one of the following procedures to select a startup device Selecting a temporary startup device Use this procedure to startup from any boot device Note Not all CDs hard disks and diskettes are startable bootable 1 2 Turn off your computer Turn on your computer and look for the following prompt on the logo screen To interrupt normal startup press Enter Press Enter when you see the prompt When the Startup Interrupt Menu displays press F12 Select the desired startup device from the Startup Device menu and press Enter to begin Note Selecting a startup device from the Startup Device menu does not permanently c
14. 00C6 Channel 5 transfer count register 00 15 Yes 00C8 Channel 6 memory address register 00 15 Yes 00CA Channel 6 transfer count register 00 15 Yes 00CC Channel 7 memory address register 00 15 Yes 00CE Channel 7 transfer count register 00 15 Yes 00D0 Channels 4 7 read status write command register 00 07 00D2 Channels 4 7 write request register 00 02 00D4 Channels 4 7 write single mask register bit 00 02 00D6 Channels 4 7 mode register write 00 07 00D8 Channels 4 7 clear byte pointer write N A 00DA Channels 4 7 master clear write temp read 00 07 00DC Channels 4 7 clear mask register write 00 03 00DE Channels 4 7 write all mask register bits 00 03 00DF Channels 5 7 8 or 16 bit mode select 00 07 40 User Guide Appendix D Interrupt request and direct memory access channel assignments The following tables list the IRQ and DMA channel assignments IRO System resource NMI Critical system error SMI System management interrupt for power management 0 Timer 1 Keyboard 2 Cascade interrupt from slave PIC 3 COM2 some models only 4 COM1 5 Available to user 6 Diskette controller 7 LPT1 8 Real time clock 9 Video ACPI 10 Available to user 11 Available to user 12 Mouse port 13 Math coprocessor 14 Primary IDE if present 15 Secondary IDE if present Note The default settings for COM 1 IR
15. ENTER All commands may be typed in either upper or lower case but not mixed To make the command line more readable spaces may be inserted between commands If you omit a parameter from a command that requires one it is just like specifying a parameter of 0 Example ATH ENTER Basic AT commands In the following listings all default settings are printed in bold text Command Function A Manually answer incoming call Al Repeat last command executed Do not precede A with AT or follow with ENTER D 0 9 A D and last number redial pulse dialing Note Pulse dialling is not supported for Australia New Zealand Norway and South Africa T touch tone dialing W wait for second dial tone pause wait for five seconds of silence flash j return to Command Mode after dialing DS n Dial one of the four telephone numbers n 0 3 stored in the modem non volatile memory EO Commands are not echoed E1 Commands are echoed Escape Characters Switch from Data Mode to Command Mode T LE S Command HO Force modem on hook hang up H1 Force modem off hook make busy Note H1 command is not supported for Italy 10 Display product identification code Copyright IBM Corp 2002 31 Command Function Il Factory ROM checksum test 2 Internal memory test 13 Firmwa
16. NetVista User Guide Type 2289 and 6824 at NetVista User Guide Type 2289 and 6824 at Note Before using this information and the product it supports be sure to read the Safety Information on page vland Appendix E Notices on page 43 Second Edition October 2002 Copyright International Business Machines Corporation 2002 All rights reserved US Government Users Restricted Rights Use duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp Contents Safety Information Lithium battery notice Modem safety information Laser compliance statement Overview Information resources Chapter 1 RN Lodel Features Specifications Available options Tools required j Handling static sensitive devices Installing external options Locating the connectors on the front of your computer Locating the contectors on the rear of your computer Obtaining device drivers Removing the cover Locating components Identifying parts on the system board Installing memory s poy Installing adapters Installing internal drives Drive specifications Installing a drive Physical security Changing the battery Replacing the cover and connecting the cables Erasing a lost or forgotten password clearing CMOS Chapter 2 Using the IBM u EL program Starting the IBM Setup Utility program Viewing and changing settings Exiting from the IBM Setup U
17. Q 4 COM 2 IRQ 3 and LPT 1 IRQ 7 can be changed to another IRQ DMA channel Data width System resource 0 8 bits Open 1 8 bits Open 2 8 bits Diskette drive 3 8 bits Parallel port for ECP or EPP 4 Reserved cascade channel 5 16 bits Open 6 16 bits Open 7 16 bits Open Copyright IBM Corp 2002 41 42 User Guide Appendix E Notices IBM may not offer the products services or features discussed in this document in all countries Consult your local IBM representative for information on the products and services currently available in your area Any reference to an IBM product program or service is not intended to state or imply that only that IBM product program or service may be used Any functionally equivalent product program or service that does not infringe any IBM intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operation of any non IBM product program or service IBM may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to IBM Director of Licensing IBM Corporation North Castle Drive Armonk NY 10504 1785 U S A INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND
18. and gently prying it loose Make sure the drive that you are installing is set correctly as either a master or a slave device If it is the first CD ROM drive or DVD ROM drive set it as a master device e If it is an additional CD ROM drive or DVD ROM drive set it as a slave device e If it is an additional hard disk drive set it as a slave device Refer to the documentation that comes with your drive for master slave jumper information Chapter 1 Installing options 17 6 Install the drive into the bay Align the screw holes and install two screws to secure the drive 7 Each integrated drive electronics IDE drive requires two cables a four wire power cable that connects to the power supply and a signal cable that connects to the system board For aCD ROM drive you might also have an audio cable The steps to connect an IDE drive are different depending on the type of drive you are connecting Use one of the following procedures for your drive connection Connecting the first IDE CD ROM drive or DVD ROM drive 1 Locate the three connector signal cable that comes with your computer or with the new drive 2 Locate the secondary IDE connector on the system board See Identifying parts on the system board on page 11 3 Connect one end of the signal cable to the drive and the other to the secondary IDE connector on the system board To reduce electronic noise use the connectors at the en
19. apters that impede access to the Clear CMOS Recovery jumper Move the jumper from the standard position pins 1 and 2 to pins 2 and 3 Replace the cover See Replacing the cover and connecting the cables on page 21 Reconnect the power cords for the computer and monitor to electrical outlets Insert the POST BIOS update flash diskette into drive A and turn on the computer and the monitor After the update session is completed there will be no video and the series of beeps will end Remove the diskette from the diskette drive and turn off the computer and monitor Unplug the power cords from electrical outlets Remove the cover See Replacing the cover and connecting the cables on Remove any adapters that impede access to the BIOS Configuration jumper Replace the Clear CMOS Recovery jumper to its original position Replace any adapters that were removed Replace the cover and reconnect any cables that were disconnected Turn on the computer to restart the operating system Appendix B Manual modem commands The following section lists commands for manually programming your modem Commands are accepted by the modem while it is in Command Mode Your modem is automatically in Command Mode until you dial a number and establish a connection Commands may be sent to your modem from a PC running communication software or any other terminal devices All commands sent to the modem must begin with AT and end with
20. canner For some external options you must install additional software in addition to making the physical connection When adding an external option use the information in this section to identify the required connector and then use the instructions that come with the option to help you make the connection and install any software or device drivers that are required for the option Locating the connectors on the front of your computer The following illustration shows the locations of the USB connectors on the front of the computer and H USB connectors Chapter 1 Installing options 7 8 User Guide Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the back of the computer NO er O Power connector Mouse connector Keyboard connector USB connectors Serial connector Parallel connector Monitor connector USB connectors E SOOEURNE A R RRRA g g efefjefefjel efe CD ESS KO DO La Kel Ethernet connector Microphone connector Audio line out connector Audio line in connector AGP slot some models Serial connector PCI slots In some models other devices such as a modem might be installed here Note Some conne
21. ce for further information about this classification 4 User Guide Available options The following are some available options e External options Parallel port devices such as printers and external drives Serial port devices such as external modems and digital cameras Audio devices such as external speakers for the sound system USB devices such as printers joysticks and scanners Security device such as a rope clip Monitors Internal options System memory called dual inline memory modules DIMMs Peripheral component interconnect PCI adapters Internal drives such as CD ROM drive or DVD ROM drive Hard disk Diskette drives and other removable media drives For the latest information about available options see the following World Wide Web pages e http www ibm com pc us options e http www ibm com pc support You can also obtain information by calling the following telephone numbers Within the United States call 1 800 IBM 2YOU 1 800 426 2968 your IBM reseller or IBM marketing representative e Within Canada call 1 800 565 3344 or 1 800 IBM 4YOU Outside the United States and Canada contact your IBM reseller or IBM marketing representative Tools required To install some options in your computer you might need a flat blade or Phillips screwdriver Additional tools might be needed for certain options See the instructions that come with the opt
22. ctors on the rear of the computer are color coded to help you to determine where to connect the cables on your computer Connector Mouse connector Keyboard connector Serial connectors Parallel connector USB connectors Ethernet connector Audio line out connector Audio line in connector Microphone connector Description Used to attach a mouse trackball or other pointing device that uses a standard mouse connector Used to attach a keyboard that uses a standard keyboard connector Used to attach an external modem serial printer or other devices that use a 9 pin serial connector Used to attach a parallel printer parallel scanner or other devices that use a 25 pin parallel connector Used to attach a device that requires a Universal Serial Bus USB connection such as a USB scanner or USB printer If you have more than four USB devices you can purchase a USB hub which you can use to connect additional USB devices Used to attach an Ethernet cable for a local area network LAN Note To operate the computer within FCC Class B limits use a Category 5 Ethernet cable Used to send audio signals from the computer to external devices such as powered stereo speakers speakers with built in amplifiers headphones multimedia keyboards or the audio line in connector on a stereo system or other external recording device Used to receive audio signals from an external audio device such as a stereo system
23. d of the cable only 4 Your computer has extra power connectors for additional drives Connect a power connector to the drive 18 User Guide 5 If you have a CD ROM audio cable connect it to the drive and to the system board See Identifying parts on the system board on page 11 Connecting an additional IDE CD ROM drive or DVD ROM drive 1 Locate the secondary IDE connector on the system board and the three connector signal cable See Identifying parts on the system board on page 11 11 2 Connect the extra connector in the signal cable to the new CD ROM drive or DVD ROM drive 3 Your computer has extra power connectors for additional drives Connect a power connector to the drive Connecting an additional IDE hard disk drive 1 Locate the primary IDE connector on the system board One end of the three connector cable connects to the hard disk drive and the other connects to the system board See Identifying parts on the system board on page 11 2 Connect the extra connector in the signal cable to the new hard disk drive 3 Your computer has extra power connectors for additional drives Connect a power connector to the drive T What to do next e To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 21 Physical security To help prevent hardware theft you can install a rope clip and
24. dministrator password Setting an administrator password deters unauthorized persons from changing configuration settings If you are responsible for maintaining the settings of several computers you might want to set an administrator password After you set an administrator password a password prompt is displayed each time you try to access the IBM Setup Utility program If you type the wrong password you will see an error message If you type the wrong password three times you must turn the computer off and start again If both the user and administrator passwords are set you can type either password However to change any configuration settings you must use your administrator password Setting changing and deleting a password To set change or delete a password do the following Note A password can be any combination of up to seven characters A Z a z and 0 9 1 Start the IBM Setup Utility program see Starting the IBM Setup Utili 2 From the IBM Setup Utility program menu select Security 3 Select Set Passwords Read the information displayed on the right side of the screen Using Security Profile by Device 26 User Guide Security Profile by Device is used to enable or disable user access to the following devices IDE controller When this feature is set to Disable all devices connected to the IDE controller such as hard disk drives or the CD ROM drive are disabled and will not be displayed in the
25. ee Removing the cover on page 10 10 3 Locate the battery See Identifying parts on the system board on page 11 4 If necessary remove any adapters that impede access to the battery See Installing adapters on page 14 for more information 5 Remove the old battery 6 Install the new battery 4 7 Replace any adapters that were removed to gain access to the battery See Installing adapters on page 14 for instructions for replacing adapters 8 Replace the cover and plug in the power cord See Replacing the cover and connecting the cables Note When the computer is turned on for the first time after battery replacement an error message might be displayed This is normal after replacing the battery 9 Turn on the computer and all attached devices 10 Use the IBM Setup Utility program to set the date and time and any passwords Replacing the cover and connecting the cables After working with options you need to install any removed parts replace the cover and reconnect any cables including telephone lines and power cords Also depending on the option that is installed you might need to confirm the updated information in the IBM Setup Utility program To replace the cover and connect cables to your computer 1 Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your co
26. el 1 memory address register 00 15 Yes 0003 Channel 1 transfer count register 00 15 Yes 0004 Channel 2 memory address register 00 15 Yes 0005 Channel 2 transfer count register 00 15 Yes 0006 Channel 3 memory address register 00 15 Yes 0007 Channel 3 transfer count register 00 15 Yes 0008 Channels 0 3 read status write command register 00 07 0009 Channels 0 3 write request register 00 02 000A Channels 0 3 write single mas register bits 00 02 000B Channels 0 3 mode register write 00 07 000C Channels 0 3 clear byte pointer write N A 000D Channels 0 3 master clear write temp read 00 07 000E Channels 0 3 clear mask register write 00 03 000F Channels 0 3 write all mask register bits 00 03 0081 Channel 2 page table address register 00 07 0082 Channel 3 page table address register 00 07 0083 Channel 1 page table address register 00 07 0087 Channel 0 page table address register 00 07 0089 Channel 6 page table address register 00 07 008A Channel 7 page table address register 00 07 008B Channel 5 page table address register 00 07 008F Channel 4 page table address refresh register 00 07 00C0 Channel 4 memory address register 00 15 Yes 00C2 Channel 4 transfer count register 00 15 Yes Appendix C System address maps 39 Address hex Description Bits Byte pointer 00C4 Channel 5 memory address register 00 15 Yes
27. erial port 3 or 4 02F8 02FF 8 COM2 0338 033F 8 Serial port 3 or 4 0340 036F 48 Available 0370 0371 2 IDE channel 1 command 0378 037F 8 LPT2 0380 03B3 52 Available 03B4 03B7 4 Video 03BA 1 Video 03BC 03BE 16 LPT1 03C0 03CF 52 Video 03D4 03D7 16 Video 03DA 1 Video 03D0 03DF 11 Available 03E0 03E7 8 Available 03E8 03EF 8 COM3 or COM4 03F0 03F5 6 Diskette channel 1 03F6 1 Primary IDE channel command port 03F7 Write 1 Diskette channel 1 command 03F7 bit 7 1 bit Diskette disk change channel 03F7 bits 6 0 7 bits Primary IDE channel status port 38 User Guide Address range hex Size bytes Description 03F8 O3FF 8 COM1 0400 047F 128 Available 0480 048F 16 DMA channel high page registers 0490 OCF7 1912 Available OCF8 OCFB 4 PCI configuration address register OCFC OCFF 4 PCI configuration data register LPTn 400h 8 ECP port LPTn base address hex 400 OCF9 1 Turbo and reset control register 0D00 FFFF 62207 Available DMA I O address map The following table lists resource assignments for the DMA address map Any addresses that are not shown are reserved Address hex Description Bits Byte pointer 0000 Channel 0 memory address register 00 15 Yes 0001 Channel 0 transfer count register 00 15 Yes 0002 Chann
28. ge 10 2 Remove the adapter slot cover for the appropriate expansion slot 3 Remove the adapter from its static protective package 14 User Guide 4 Install the adapter into the appropriate slot on the system board 5 Secure the adapter with the screw as shown What to do next e To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 21 Installing internal drives This section provides information and instructions for installing and removing internal drives Internal drives are devices that your computer uses to read and store data You can add drives to your computer to increase storage capacity and to enable your computer to read other types of media Some of the different drives that are available for your computer are Hard disk drives e CD ROM drives or DVD ROM drives e Removable media drives Internal drives are installed in bays In this book the bays are referred to as bay 1 bay 2 and so on When you install an internal drive it is important to note what type and size of drive that you can install in each bay Also it is important to correctly connect the internal drive cables to the installed drive Chapter 1 Installing options 15 Drive specifications 16 User Guide Your computer comes with the following IBM installed drives e A CD ROM drive or DVD ROM
29. gle 32 User Guide Command Function amp D2 Modem hangs up returns to the Command Mode after DTR toggle amp D3 Resets modem after DTR toggle amp F_ amp F Recall factory default configuration amp G_ amp G0 Guard tone disabled amp G1 Guard tone disabled amp G2 1800 Hz guard tone amp K_ amp KO Disable flow control amp K3 Enable RTS CTS hardware flow control amp K4 Enable XON XOFF software flow control amp K5 Enable transparent XON XOFF flow control amp K6 Enable both RTS CTS and XON XOFF flow control amp M_ amp M0_ Asynchronous operation amp P_ amp P0 US setting for off hook to on hook ratio amp P1 UK and Hong Kong off hook to on hook ratio amp P2 Same as amp P0 setting but at 20 pulses per minute amp P3 Same as amp P1 setting but at 20 pulses per minute amp R_ amp RO Reserved amp R1 CTS operates per flow control requirements amp S_ amp S0 Force DSR Signal High ON amp S1 DSR off in command mode on in on line mode amp T_ amp TO Ends test in progress amp T1 Perform Local Analog Loopback Test amp T3 Perform Local Digital Loopback Test amp T4 Grant Remote Digital Loopback Test request by remote modem amp T5 Deny Remote Digital Loopback Test request amp T6 Perform a Remote Digital Loopback Test amp T7 Perform a Remote Digital Loopback Test and Self Test amp
30. hange the startup sequence Changing the startup device sequence To view or permanently change the configured startup device sequence do the following 1 5 Start the IBM Setup Utility program see Starting the IBM Setup Utilit Select Startup Select Startup Sequence See the information displayed on the right side of the screen Select the devices for the Primary Startup Sequence the Automatic Startup Sequence and the Error Startup Sequence Select Exit from the IBM Setup Utility menu and then Save Settings If you have changed these settings and want to return to the default settings select Load Default Settings on the Exit menu Chapter 2 Using the IBM Setup Utility program 27 28 User Guide Appendix A Updating System Programs The following contains information about updating system programs POST BIOS and how to recover from a POST BIOS update failure System programs System programs are the basic layer of software that is built into your computer They include the power on self test POST the basic input output system BIOS code and the IBM Setup Utility program POST is a set of tests and procedures that is performed each time you turn on your computer BIOS is a layer of software that translates instructions from other layers of software into electrical signals that the computer hardware can understand You can use the IBM Setup Utility program to view and change the configuration and setup of you
31. hitecture Memory Support for two dual inline memory modules DIMMs 2 5 V 184 pin 266MHz double data rate synchronous dynamic random access memory DDR SDRAM 128 MB 256 MB 512 MB or 1 0 GB when available DIMMs in any combination See Installing memory on page 12 for additional information e 512 KB flash memory for system programs Internal drives 2 User Guide e 3 5 inch 1 44 MB diskette drive e Internal hard disk drive e EIDE CD ROM or DVD ROM drive some models Video subsystem Dynamic video memory technology Accelerated graphics port AGP video adapter slot on the system board some models Audio subsystem Integrated SoundMax 3 audio subsystem Connectivity 10 100 Mbps integrated Intel Ethernet controller that supports the Wake on LAN feature e 56K V 90 data fax PCI modem some models System management features Remote Program Load RPL and Dynamic Host Configuration Protocol DHCP e Wake on LAN Wake on Ring in the IBM Setup Utility program this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem Remote Administration Automatic power on startup System Management SM BIOS and SM software e Ability to store POST hardware test results Input output features e 25 pin Extended Capabilities Port ECP Extended Parallel Port EPP e Two 9 pin serial connectors Six 4 pin USB connectors supports up t
32. ion Handling static sensitive devices Static electricity although harmless to you can seriously damage computer components and options When you add an option do not open the static protective package containing the option until you are instructed to do so When you handle options and other computer components take these precautions to avoid static electricity damage Limit your movement Movement can cause static electricity to build up around you Always handle components carefully Handle adapters and memory modules by the edges Never touch any exposed circuitry Prevent others from touching components Chapter 1 Installing options 5 When you install a new option touch the static protective package containing the option to a metal expansion slot cover or other unpainted metal surface on the computer for at least two seconds This reduces static electricity in the package and your body When possible remove the option and install it directly in the computer without setting the option down When this is not possible place the static protective package that the option came in on a smooth level surface and place the option on it Do not place the option on the computer cover or other metal surface Installing external options 6 User Guide This section shows the various external connectors on your computer to which you can attach external options such as external speakers a printer or a s
33. ions available to PCI bus 0020 0021 2 Interrupt controller 1 0022 003F 30 General I O locations available to PCI bus 0040 0043 4 Counter timer 1 0044 OOFF 28 General I O locations available to PCI bus 0060 1 Keyboard controller byte reset IRQ 0061 1 System port B 0064 1 Keyboard controller CMD ATAT byte 0070 bit 7 1 bit Enable NMI 0070 bits 6 0 6 bits Real time clock address 0071 1 Real time clock data 0072 1 bit Enable NMI 0072 bits 6 0 6 bits RTC address 37 Address range hex Size bytes Description 0073 1 RTC data 0080 1 POST checkpoint register during POST only 008F 1 Refresh page register 0080 008F 16 DMA page registers 0090 0091 15 General I O locations available to PCI bus 0092 1 PS 2 keyboard controller registers 0093 009F 15 General I O locations 00A0 00A1 2 Interrupt controller 2 00A2 OOBF 30 APM control 00C0 00DF 31 DMA 2 OOEO OOEF 16 General I O locations available to PCI bus OOFO 1 Coprocessor error register OOF1 016F 127 General I O locations available to PCI bus 0170 0177 8 Secondary IDE channel O1F0 01F7 8 Primary IDE channel 0200 0207 8 MIDI joystick port 0220 0227 8 Serial port 3 or 4 0228 0277 80 General I O locations available to PCI bus 0278 027F 8 LPT3 0280 02E7 102 Available 02E8 02EF 8 S
34. meters FDR Begin or continue phase C receive data FDT Data transmission FDTC Report the polled station capabilities FET Post page message response FET N Transmit page punctuation FHNG Call termination with status FK Session termination FLID Local ID string FLPL Document for polling FMDI Identify model FMFR Identify manufacturer FPHCTO Phase C time out FPOLL Indicates polling request FPTS Page transfer status FPTS Page transfer status FREV Identify revision FSPT Enable polling FTSI Report the transmit station ID Voice commands BDR Select Baud Rate CID Enable Caller ID detection and reporting format CLS Select Data Fax or Voice Audio MDL Identify Model MFR Identify Manufacturer REV Identify Revision Level TL Audio output transmit level Appendix B Manual modem commands 35 VBQ Query Buffer Size VBS Bits per sample ADPCM or PCM VBT Beep Tone Timer VCI Identify Compression Method VLS Voice line select VRA Ringback goes away timer VRN Ringback never came timer VRX Voice Receive Mode VSDB Silence deletion tuner VSK Buffer skid setting VSP Silence detection period VSR Sampling rate selection VSS Silence deletion tuner VTD DTMF tone reporting capability VTM Enable timing mark placement VTS Generate tone signals Voice transmit mode
35. mputer 2 Clear any cables that might impede the replacement of the cover Chapter 1 Installing options 21 3 Position the cover on the chassis so that the guides on the top and bottom of the cover engage the chassis and push the cover to the closed position Insert the screws that secure the cover 4 Reconnect the external cables and power cords to the computer See Installing external options on page 6 5 To update the configuration see Chapter 2 Using the IBM Setup Utilit m Important When the power cord is first plugged in the computer might appear to turn on for a few seconds and then turn off This is a normal sequence to enable the computer to initialize Erasing a lost or forgotten password clearing CMOS This section applies to lost or forgotten passwords For more information about lost or forgotten passwords go to Access IBM To erase a forgotten password 1 Turn off the computer and all attached devices Unplug the power cord Remove the cover See Removing the cover on page 10 Locate the Clear CMOS Recovery jumper on the system board See Identifying parts on the system board on page 11 5 If necessary see Installing adapters on page 14 to remove any adapters that impede access to the Clear CMOS Recovery jumper 5 D 22 User Guide 6 Move the jumper from the standard position pins 1 and 2 to the maintenance or co
36. nfigure position pins 2 and 3 7 Replace the cover and connect the power cord See Replacing the cover and connecting the cables on page 21 8 Restart the computer leave it on for approximately 10 seconds and then hold the power switch for approximately 5 seconds to turn the computer off 9 Repeat steps 2 through 4 on page 22 10 Move the jumper back to the standard pins 1 and 2 11 Replace the cover and connect the power cord See Replacing the cover and connecting the cables on page 21 Chapter 1 Installing options 23 24 User Guide Chapter 2 Using the IBM Setup Utility program The IBM Setup Utility program is stored in the electrically erasable programmable read only memory EEPROM of your computer The IBM Setup Utility program is used to view and change the configuration settings of your computer regardless of which operating system you are using However the operating system settings might override any similar settings in the IBM Setup Utility program Starting the IBM Setup Utility program To start the IBM Setup Utility program do the following 1 If your computer is already on when you start this procedure shut down the operating system and turn off the computer 2 Turn on your computer and look for the following prompt on the logo screen To interrupt normal startup press Enter Press Enter when you see the prompt 3 Press F1 to start the IBM Setup Utility Note If a user pas
37. nk E PCI slots A DIMMs EI PCI adapter AGP slot some models Bl Power supply Identifying parts on the system board The system board sometimes called the planar or motherboard is the main circuit board in your computer It provides basic computer functions and supports a variety of devices that are IBM installed or that you can install later Chapter 1 Installing options 11 The following illustration shows the locations of parts on the system board ji dm f i o 16 m Ca 15 Fa 13 a Microprocessor A DIMM connector 1 DIMM connector 2 E Power connector E Diskette drive connector f Primary IDE connector Front panel connector E Secondary IDE connector EI Battery Clear CMOS Recovery jumper SCSI LED connector PCI slots Front panel audio connector CD ROM audio connector AGP slot some models Serial connector Installing memory 12 User Guide Your computer has two connectors for installing dual inline memory modules DIMMs that provide up to a maximum of 2 0 GB of system memory When installing DIMMs the following rules apply Fill each system
38. o USB 2 0 e PS 2 mouse connector e PS 2 keyboard connector Ethernet connector Monitor connector e Three audio connectors line in line out and microphone Expansion Four drive bays Three 32 bit peripheral component interconnect PCI adapter slots One accelerated graphics port AGP expansion slot some models Power e 180 W power supply with manual voltage selection switch Automatic 50 60 Hz input frequency switching e Advanced Power Management support e Advanced Configuration and Power Interface ACPI support Security features User and administrator passwords Support for the addition of a rope clip and lockable cable Support for the addition of an integrated cable lock see Access IBM Support for a padlock on the chassis Startup sequence control Startup without diskette drive keyboard or mouse Unattended start mode Diskette and hard disk I O control Serial and parallel port I O control Security profile by device IBM preinstalled software Your computer might come with preinstalled software If it does an operating system device drivers to support built in features and other support programs are included Operating systems preinstalled varies by model type Note Not all countries or regions will have these operating systems e Microsoft Windows XP Professional Microsoft Windows XP Home Microsoft Windows 2000 Professional Operating sys
39. onnected at the network interface Use caution when installing or modifying telephone lines Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning e Do not use the telephone to report a gas leak in the vicinity of the leak Consignes de s curit relatives au modem Lors de l utilisation de votre mat riel t l phonique il est important de respecter les consignes ci apr s afin de r duire les risques d incendie d lectrocution et d autres blessures e N installez jamais de cordons t l phoniques durant un orage Les prises t l phoniques ne doivent pas tre install es dans des endroits humides except si le mod le a t con u cet effet Ne touchez jamais un cordon t l phonique ou un terminal non isol avant que la ligne ait t d connect e du r seau t l phonique e Soyez toujours prudent lorsque vous proc dez l installation ou la modification de lignes t l phoniques Si vous devez t l phoner pendant un orage pour viter tout risque de choc lectrique utilisez toujours un t l phone sans fil e En cas de fuite de gaz n utilisez jamais un t l phone situ proximit de la fuite Laser compliance statement Some IBM Personal Computer models are equipped from the factory with a CD ROM drive or a DVD ROM drive CD ROM drives and DVD ROM drives are also sold separately as option
40. r computer Your computer system board has a module called electrically erasable programmable read only memory EEPROM also referred to as flash memory You can easily update POST BIOS and the IBM Setup Utility program by starting your computer using a flash update diskette or by running a special update program from your operating system IBM might make changes and enhancements to the system programs When updates are released they are available as downloadable files on the World Wide Web see the Quick Reference Instructions for using the system program updates are available in txt file that is included in the update files For most models you can download either an update program to create a system program update flash diskette or an update program that can be run from the operating system Updating flashing BIOS from a diskette 1 Insert a system program update flash diskette into the diskette drive drive A in your computer System program updates are available at http www ibm com pc support on the World Wide Web 2 Turn on the computer If it is on already you must turn it off and back on again The update begins Updating flashing BIOS from your operating system Note Due to constant improvements being made to the IBM Web site Web page content including the links referenced in the following procedure is subject to change 1 From your browser type http www pc ibm com support in the address field and
41. rating 4 Ethernet connector 9 IBM Setup Utility 25 input output I O address map 37 features 2 installing options adapters 14 DIMMs 12 internal drives 17 Copyright IBM Corp 2002 installing options continued memory 12 rope clip 19 K keyboard connector 9 L locating components 11 M memory dual inline memory modules DIMMs 12 installing 12 map 37 system 5 12 microphone connector 9 modem Basic AT commands 31 Extended AT commands 32 Fax Class 1 commands 34 Fax Class 2 commands 34 MNP V 42 V 42bis V 44 commands 34 Voice commands 35 mouse connector 9 N noise level 4 O options available 5 external 5 internal 5 P parallel connector 9 password erasing lost or forgotten 22 setting changing deleting 26 power Advanced Configuration and Power Interface ACPI support 3 Advanced Power Management support 2 R recovering from a POST BIOS update failure 29 removing the cover 10 replacing the cover 21 45 S security rope clip 19 security profile by device 26 serial connectors 9 startup sequence 27 system address maps 37 system board connectors 12 identifying parts 11 location 12 memory 5 11 system programs updating 29 U updating system programs 29 USB connectors 9 using security profile by device 26 V video subsystem 2 46 User Guide Part Number 49P1040 Printed in U S A 1P P N 49P1040
42. re ID 14 Reserved ID L_ LO Low speaker volume L1 Low speaker volume L2 Medium speaker volume L3 High speaker volume M_ MO Internal speaker off M1 Internal speaker on until carrier detected M2 Internal speaker always on M3 Internal speaker on until carrier detected and off while dialing N Included for compatibility only provides no effect Return to Data Mode Return to Data Mode and initiate an equalizer retrain Set Pulse dial as default Modem sends responses Modem does not send responses Read and display value in register r Set register r to value n n 0 255 T Set Tone Dial as default V_ vo Numeric responses V1 Word responses W_ WO Report DTE speed only W1 Report line speed error correction protocol and DTE speed W2 Report DCE speed only X_ XO Hayes Smartmodem 300 compatible responses blind dialing X1 Same as X0 plus all CONNECT responses blind dialing X2 Same as X1 plus dial tone detection X3 Same as X1 plus busy detection blind dialing X4 All responses and dial tone and busy signal detection Z_ ZO Reset and retrieve active profile 0 Z1 Reset and retrieve active profile 1 Extended AT commands Command Function amp C_ amp C0 Force Carrier Detect Signal High ON amp C1 Turn on CD when remote carrier is present amp D_ amp D0 Modem ignores the DTR signal amp D1 Modem returns to Command Mode after DTR tog
43. reil laser Aux tat Unis l unit de CD ROM DVD ROM est certifi e conforme aux normes indiqu es dans le sous chapitre J du DHHS 21 CFR relatif aux produits laser de classe 1 Dans les autres pays elle est certifi e tre un produit laser de classe 1 conforme aux normes CEI 825 et CENELEC EN 60 825 Lorsqu une unit de CD ROM DVD ROM est install e tenez compte des remarques suivantes ATTENTION Pour viter tout risque d exposition au rayon laser respectez les consignes de r glage et d utilisation des commandes ainsi que les proc dures d crites L ouverture de l unit de CD ROM DVD ROM peut entra ner un risque d exposition au rayon laser Pour toute intervention faites appel du personnel qualifi Certaines unit s de CD ROM DVD ROM peuvent contenir une diode laser de classe 3A ou 3B Tenez compte de la consigne qui suit DANGER Rayonnement laser lorsque le carter est ouvert vitez toute exposition directe des yeux au rayon laser vitez de regarder fixement le faisceau ou de l observer l aide d instruments optiques Overview Thank you for selecting an IBM computer Your computer incorporates many of the latest advances in computer technology and can be upgraded as your needs change Instructions for installing options are included in this publication When adding an option use these instructions along with the instructions that come with the option Information resource
44. ression only C2 Enable V 42bis data compression only C3 Enable MNP Class 5 and V 42bis data compression amp Q_ amp Q0 Direct data link only same as N1 amp Q5 V 42 data link with fallback options amp Q6 Normal data link only same as NO DS44 0 0 Disable V 44 DS44 3 0 Enable V 44 DS44 Current values DS44 List of support values Fax Class 1 commands FAE n Data Fax Auto Answer FCLASS n Service Class FRH n Receive data with HDLC framing FRM n Receive data FRS n Receive silence FTH n Transmit data with HDLC framing FTM n Transmit data FTS n Stop transmission and wait Fax Class 2 commands FCLASS n Services class FAA n Adaptive answer FAXERR Fax error value FBOR Phase C data bit order 34 User Guide FBUF Buffer size read only FCFR Indicate confirmation to receive FCLASS Service class FCON Facsimile connection response FCIG Set the polled station identification FCIG Report the polled station identification FCR Capability to receive FCR Capability to receive FCSI Report the called station ID FDCC DCE capabilities parameters FDCS Report current session FDCS Current session results FDIS Report remote capabilities FDIS Current sessions para
45. s The Quick Reference that comes with your computer provides information for installing your computer and starting the operating system It also includes basic troubleshooting information software recovery procedures help and service information and warranty information Access IBM provides a link to more information about your computer Click Start gt Access IBM If you have Internet access the most up to date manuals for your computer are available from the World Wide Web To access this information point your browser to http www ibm com pc support Type your machine type and model number in the Quick Path field and click Go Copyright IBM Corp 2002 ix X User Guide Chapter 1 Installing options This chapter provides an introduction to the features and options that are available for your computer You can expand the capabilities of your computer by adding memory adapters or drives When installing an option use these instructions along with the instructions that come with the option Important Before you install or remove any option read Safety Information on page v These precautions and guidelines will help you work safely Features Copyright IBM Corp 2002 This section provides an overview of the computer features and preinstalled software Microprocessor Intel Pentium 4 processor with either 256 KB or 512 KB of internal L2 cache memory and Intel NetBurst micro arc
46. s CD ROM drives and DVD ROM drives are laser products These drives are certified in the U S to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations DHHS 21 CFR Subchapter J for Class 1 laser products Elsewhere these drives are certified to conform to the requirements of the International Electrotechnical Commission IEC 825 and CENELEC EN 60 825 for Class 1 laser products When a CD ROM drive or a DVD ROM drive is installed note the following handling instructions CAUTION Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure Removing the covers of the CD ROM drive or DVD ROM drive could result in exposure to hazardous laser radiation There are no serviceable parts inside the CD ROM drive or DVD ROM drive Do not remove the drive covers Some CD ROM drives and DVD ROM drives contain an embedded Class 3A or Class 3B laser diode Note the following statement Safety Information vii viii User Guide DANGER Laser radiation when open Do not stare into the beam do not view directly with optical instruments and avoid direct exposure to the beam DANGER Certains mod les d ordinateurs personnels sont quip s d origine d une unit de CD ROM ou de DVD ROM Mais ces unit s sont galement vendues s par ment en tant qu options L unit de CD ROM DVD ROM est un appa
47. sword is set you must type the password to continue If an administrator password has been set you cannot make any changes to configuration using the IBM Setup Utility program until you type your administrator password See for more information The IBM Setup Utility might start automatically when POST detects that hardware has been removed or new hardware has been installed in your computer Viewing and changing settings The IBM Setup Utility program menu lists items that identify system configuration topics When working with the IBM Setup Utility program menu you must use the keyboard The keys used to perform various tasks are displayed at the bottom of each screen Exiting from the IBM Setup Utility program When you finish viewing or changing settings press Esc to return to the IBM Setup Utility program menu you might have to press Esc several times If you want to save the new settings select Save Settings before you exit Otherwise your changes will not be saved Using passwords You can use passwords to provide security for your computer and data There are two kinds of passwords a user password and an administrator password You do not have to set a password of either type to use your computer However if you decide to set either one read the following sections Copyright IBM Corp 2002 25 User password The user password feature deters unauthorized persons from gaining access to your computer A
48. tems tested for compatibility e Microsoft Windows NT Workstation Version 4 0 e Microsoft Windows 98 Second Edition 1 The operating systems listed here are being tested for compatibility at the time this publication goes to press Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet Corrections and additions to this list are subject to change To determine if an operating system has been tested for compatibility check the Web site of the operating system vendor Chapter 1 Installing options 3 Specifications This section lists the physical specifications for your computer Dimensions Height 398 mm 15 67 in Width 180 mm 7 08 in Depth 402 mm 15 82 in Weight Minimum configuration as shipped 7 6 kg 16 8 Ib Maximum configuration 9 97 kg 22 Ib Environment Air temperature System on 10 to 35 C 50 to 95 F System off 10 to 43 C 50 to 110 F Maximum altitude 2134 m 7000 ft Note The maximum altitude 2134 m 7000 ft is the maximum altitude at which the specified air temperatures apply At higher altitudes the maximum air temperatures are lower than those specified Humidity System on 8 to 80 System off 8 to 80 Electrical input Input voltage Low range Minimum 90 V ac Maximum 135 V ac Input frequency range 47 63 Hz Voltage switch setting 115 V ac High range Minimum 180 V ac Maximum 265
49. tility program Using passwords User password Copyright IBM Corp 2002 vi Vi vii 10 11 11 12 14 15 16 17 19 20 21 22 25 25 25 25 25 26 Administrator password Ta Setting changing and deleting a password Using Security Profile by Device Selecting a startup device Selecting a temporary startup device Changing the startup device sequence Appendix A u en Programs System programs Updating flashing BIOS Kom a diskette Updating flashing BIOS from your Ben system Recovering from a POST BIOS update filare Appendix B Manual modem commands Basic AT commands Extended AT commands MNP V 42 V 42bis V 44 commands Fax Class 1 commands Fax Class 2 commands Voice commands Appendix C System address maps System memory map s tds eg I O address map DMA I O address map Appendix D Interrupt request and direct memory access channel assignments Appendix E Notices Television output notice Trademarks Index 26 26 26 427 27 27 29 29 29 29 30 31 lt 31 32 34 34 34 35 37 Oe 2 OF 39 41 43 43 44 45 iii iv User Guide Safety Information DANGER Electrical current from power telephone and communication cables is hazardous To avoid a shock hazard Do not connect or disconnect any cables or perform installation maintenance
50. ust be authorized by Macrovision Corporation and is Copyright IBM Corp 2002 43 intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited Trademarks 44 User Guide The following terms are trademarks of the IBM Corporation in the United States or other countries or both IBM NetVista Wake on LAN PS 2 05 2 Intel NetBurst and Pentium are trademarks or registered trademarks of Intel Corporation in the United States other countries or both Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States other countries or both Other company product and service names may be trademarks or service marks of others Index A adapters installing 14 peripheral component interconnect PCI 5 slots 14 address map DMA input output I O 39 input output I O 37 system memory 37 audio line in connector 9 audio line out connector 9 audio subsystem 2 C cables connecting 21 changing the battery 20 commands Basic AT 31 Extended AT 32 Fax Class 1 34 Fax Class 2 34 MNP V 42 V 42bis V 44 34 Voice 35 connector description 9 cover removing 10 replacing 21 D device drivers 9 DMA I O address map 39 drives bays 2 16 CD 5 15 diskette 5 DVD 5 15 hard disk 5 15 installing 17 internal 1 5 15 removable media 5 15 specifications 16 E environment ope
Download Pdf Manuals
Related Search