Husqvarna 347 Brush Cutter User Manual
Contents
1. During use to prevent problems in starting the engine again we strongly recommend that you avoid letting the fuel run out in the tank Fuel storage A DE Store the fuel in a cool well ventilated place in an approved fuel storage container Never store the engine with fuel in the tank in a poorly ventilated place where the fumes produced by the gasoline could propagate and reach a fire candle burner or furnace pilot light water heater dryer etc Never store excessive quantities of fuel E Assembly disassembly E1 Delta grip ABHE For your safety fasten the delta handle in front of the label placed on the shaft at a distance of at least 18 cm from the rear grip The handle should be fastened in a comfortable working position The safety pole guard should be mounted using the accessories supplied and in the configura tion shown in the figure in contact with the delta handle E2 Double Handle Adjust and secure double hand clamp by tighten ing the screws E3 Assembly of safety guard Fit the safety guard A against the gearbox I position the lower clamp G in the housing under the shield and the upper clamp F over the shaft Insert and tighten the screws H Safety guard extension exclusively for use with nylon string head e The extension B should be installed only for use with the nylon string head with the aid of the string cutter blade L that regulates the length of the string and thus the2. be able to release the machine quickly The harness is equipped with a fasten release mechanism The harness enables the operator to support the machine during use see Safety pre cautions B7 D Fuel Mixture Preparation of the mixture ABB Do not use any other type of fuel than the type recommended in this manual This machine is equipped with a two stroke engine and should therefore be fueled with a mixture of unleaded gasoline with a minimum octane rating 90 and fully synthetic oil specific for two speed engines that use unleaded gasoline in the propor tions indicated in the table on the cover fig D Control the specifications of the oil shown on the package the use of oil lacking the specifications expressly indicated in this manual could cause serious damage to the engine To obtain the best mixture pour the oil into an approved container first followed by the gasoline and shake the container well every time you take fuel out of it The characteristics of the mixture tend to deteriorate in time So you should only prepare as much mixture as you are going to need the use of deteriorated fuel can seriously damage the engine Filling the tank A BE Clean the area around the fuel cap before remov ing it to prevent any impurities from contaminat ing the fuel Take the cap off the fuel container carefully Unscrew the cap on the fuel tank and fill it with the necessary quality using a funnel
3. material to be cut I1 Drawing out the string During cutting the nylon string wears naturally causing an increase in the speed of the engine and a reduced cutting capacity When this hap pens to bring out more string bump the head against the ground release the throttle trigger to reduce the engine speed to less than 8000 rom Tap gently on the ground with the button A as shown in the figure and the string will come out automatically Accelerate again If the string does not come out make sure there is still some left and try again I2 Thinning grass with the grass cutter blade ABB The grass is cut with swinging motions from side to side maintaining the blade parallel to the ground During the right to left swing the grass is cut while the backswing must be made without using the blade KICKBACK can occur when cutting is done with the risk sector of the blade we recommend cutting with the rest of the blade Take care that the cup supporting the blade just grazes the ground This will prevent the blade from touching the ground L Environmental information This section contains information useful for main taining the characteristics of eco compatibility included in the origin design of the machine and as regards proper use and disposal of oil and fuel Design In the design stage care was taken to develop an engine with reduced consumption and low emis sions of noise and pollutant exhaust fumes Use of mach
4. models only 1 Loosen the joint knob first then insert attach ment s shaft into the shaft attachment joint and make sure that the locking pin A is Secured in one of its housings finally lock firmly the joint Knob B 2 To remove the attachment from the power unit loosen the joint knob 1 push the locking pin 2 and keeping it pressed remove attach ment s shaft from the joint s 3 Every attachment manual explains through a picture in which ways each attachment can be assembled on the power unit a configuration is forbidden if crossed if marked with NO and or the symbol X or if it isn t shown at all A configuration is allowed if marked with OK and or the symbol d The figure shows assembling configurations allowed for the string head grass blade attach ment with the rules defined in the previous para graph it is forbidden to assemble the string head grass blade attachment with the locking pin in both left and right housings allowing its assembling in the upper housing only A BEOEEEDRHEEh CAUTION Start the brush cutter in a flat place During startup stand in a stable position Make sure the blade or nylon string head do not touch the ground or any obstacles CAUTION Grip the knob of the starter with one hand and hold the machine in a stable position with the other Take care not to wind the starter string around your hand and pull slowly until you encounter some resistance then
5. pressed at the same time fig A no 19 By means of 2 separate springs upon releasing the grip the throttle trigger fig A no 3 and safety lever fig A no 19 return automatically to their original positions Engine stop device Turn the stop button Stop fig A no 7 to O STOP to stop the engine To make sure this but ton works properly start the engine and check that it stops when the Stop button is turned to the Stop position Protection for transport A BD Never use a machine with the blade cover Still on The guard covers the sharp extremities of the ENGLISH 4 blade when the machine is in the resting position for transport or storage Safety guard ABBHHD This very important safety device fig A no 19 prevents any objects that come into contact with the cutting device or the grass itself from flying up and striking the operator Safety pole guard ABBE This device fastened to the machine ensures a minimum distance between the operator and the cutting device during use and prevents the machine from striking and injuring the operator if the blade hits a hard surface fig A no 20 Muffler A HERE DREI The muffler serves to reduce the noise level to a minimum and to route the exhaust fumes pro duced by the combustion engine away from the operator Harness CAUTION It is very important to famil iarize yourself with the release mecha nism In case of emergency you need to
6. pull the cord sharply and forcefully to start the engine when Do not pull the starter cord all the way and do not release it abruptly against the machine as this could damage it COLD ENGINE STARTING 1 Move stop switch to the ON position 2 Depress the safety lever S squeeze the accelerator trigger A and push the throttle advance forwards B Now release the accelera tor trigger A and then the throttle advance B WARNING when the throttle advance is engaged the head or blade rotates 3 Move choke lever E to the closed position I l 4 Press the primer bulb C several times until ENGLISH 6 you see fuel going back to carburetor through pipe D Pull starter rope until engine fires once 5 Move choke lever E to the open position then pull starter rope until engine fires Let engine run for a few seconds holding the trimmer Now disengage throttle advance by pulling trigger completely Engine will now keep on running at idle speed HOT ENGINE STARTING STOP switch on START position Trigger on idle position released Choke towards open position MM Press the primer bulb C several times until you see fuel going back to carburetor through pipe D Pull starter rope WARNING when the throttle B advance is engaged the head or blade rotates 6 ENGINE STOPPING Press the stop switch moving it to STOP position 0 WARNING when the engine is switched off rotat ing parts blade or nylo
7. same direction and fas ten the end of each string in the 2 opposite grooves Replace the reel in its housing and thread the ends of the strings in their bushings Pull each string so that about 15 cm comes out on each side Reassemble the nylon string head as shown If the reel becomes excessively worn replace it with a whole new reel H3 Attachments maintenance Follow maintenance instructions on the attach ment manual I Techniques for use A HDH O H 2 E ee IU Cutting techniques During the cutting operations keep the engine running at high speed After every cutting stage decelerate the engine to minimum speed as running it at top speed without a load can damage the engine severely Wait until the engine is running at minimum speed before moving the machine from one section to another The machine is ideal to complete the work of the lawnmover In fact it can reach places where a ENGLISH 7 normal lawnmower is unable to go Cutting and trimming grass borders with the nylon string head Cutting with the nylon string head is suitable for light jobs like trimming borders and cutting the grass around trees Mowing To prevent damage to your lawn or the cutting mechanism keep the string parallel to the ground but avoid contact with the terrain Trimming borders Angle the nylon string head keeping it a short dis tance from the ground Cut using the end of the string Do not press the string against the
8. 68 EEC EEC Marking Directive amp 89 336 EEC Electromagnetic Compatibility Directive directive 2000 14 EEC Enclosure V Yous Di Valmadrera 15 10 06 Giuseppe Todero Technical Manager Husqvarna Outdoor Products Italy S p A Via Como 72 23868 Valmadrera Lecco ITALY O Technical data Displacement CMNO E 34 40 Bore AN 2 uyana e a a A Las aypa basis saa p E 38 40 SEENEN ae ee 30 32 Ermgiriecoutur KW OO EEN E 1 5 Maximum shaft rotation frequency M N EE 7 700 7 700 Rotation speed frequency of rotation of engine at maximum rotation frequency recommended Tor shat miN ege 12 100 12 100 Engine speed at max GOwer MIN EE 8 000 8 000 Minimani speed mN WEE 2 800 2 800 Maximum speed no load IN irass hone aa a a a aE a 10 000 10 000 leet EE 7 1 7 3 F el tane e ere EE 1000 1000 Blade locking nut tightening torque NM EE 17 17 Noise pressure at operator ear Lpav ABA ISO 071 97 97 Measured sound power level Lwav ABA ISO 10884 rr rrr 113 113 Guaranteed noise level LWav ABA ISO 10804 114 114 Vibrations level string head ISO 7916 m s MAX MIN r rr 8 2 1 6 8 2 1 7 Vibrations level blade ISO 7916 m s max min alas Ehe 8 2 1 6 8 2 1 7 ENGLISH 9
9. GUARD FOR THE CUTTING DEVICE IN USE IS NOT SECURELY FASTENED see chapter Assembly disassembly Failure to follow this rule can expose you to serious danger such as e possible contact with rotating and cutting parts e possible contact with flying debris Never use a brush cutter without its safety pole guard correctly in place Only use blades or nylon string heads clearly marked with a maximum speed of at least 10 500 min Use only original or approved accessories and spare parts which you can purchase from our official distributors The use of other accessories and spare parts increases the danger of injury and in this case the manufacturer has no liability for damage to persons or property Never attempt to use the machine if it is incomplete defective or has been altered by any one other than an Authorized Service Center The risk of accidents increases considerably if maintenance is not carried our regularly in a professional way In case of doubt contact an authorized service center All operations of maintenance assembly disas sembly and fueling should be done with the machine on a flat solid surface so that the motor can not turn over in a stable position with the motor off the switch turned to O STOP the cutting tool stopped and wearing adequate protective gloves Apparel Dress suitably for the job wear approved personal protection gear e Closely fitting protective clothing do not wear shorts or loose
10. Husqvarna Outdoor Products Italia SpA Via Como 72 23868 Valmadrera LC ITALIA Phone 39 0341 203111 Fax 39 0341 581671 PN 249955 REV 00 10 06 GB DE FR NL NO FI SE DK ES PT INSTRUCTION MANUAL IMPORTANT INFORMATION Please read these instructions care fully and make sure you understand them before using this unit Retain these instructions for future reference BETRIEBSANWEISUNG WICHTIGE INFORMATION Lesen Sie diese Hinweise zur Handha bung des Ger ts aufmerk sam durch Verwenden Sie es erst wenn Sie sicher sind da Sie alle Anweisungen verstanden haben und gut aufbewahren MANUEL D INSTRUCTIONS RENSEIGNEMENTS IMPORTANTS Avant d utiliser cet appareil veuillez lire aten tivement les instructions et assurez vous de les avoir com prises Conservez les instructions pour r f rence ult rieure HANDLEIDING BELANGRIJKE IMPORTANTS Lees deze handleiding aan dachtig en zorg dat u ailes begrijot alvorens de kettingzaag te gebrulken en be waar ze voor toekomstige raadpleging BRUKERHANDBOK VIKTIG INFORMASJON Les disse anvisningene n ye og forsikre deg om at du forstar dem for du bruker enheten og oppbevar dem for sen ere bruk OHJEKIRJA T RKE TIETOA Lue n m ohjeet huolellisesti ja varmista ett olet ymmartanyt ne ennen kuin alat k ytt t t laitetta ja s ilyt my hemp tarvetta varten BRUKSANVISNING VIKTIG INFORMATION L s instruktionerna noggrant och f rs
11. MTIKO2 MINAKA TIA THN ENIZHMANSH TOY KATAAAHAOY MPOOYAAKTHPA ME AIAQOPA KONTIKA EZAPTHMATA GA SHRNUJ C TABULKA PRO SPR VNOU KOMBINAC REZNA HLAVA BEZPECNOSTNI OCHRANA G TABELA ZBIORCZA POPRAWNEGO ZESTAWIENIA G OWICY TNACEJ OS ONY ZABEZPIECZAJ CEJ Q TABELA POVZETEK ZA PRAVILNO POVEZAVO GLAVA ZASCITA QD O530PHAA TABHIVLIA ANA NPABUNbHOrO COYETAHMA PE UE OJIOBKI NPEAOXPAHUTESIbHOrO YCTPOUCTBA B KOKKUVOTLIK TABEL TRIMMIPEA JA SELLE KAITSME KORREKTSEKS MONTEERIMISEKS GD NOSL GUMA TABULA PAREIZAI GRIESANAS _ GALVINAS UN DRO BAS AIZSARGA SAVIENOSANAI 20GRU BIR G Y M EKL N ZETLEY C TABELA KES C KAFA EMN YET KORUNMASI A General description 1 ENGINE 2 SHAFT 3 THROTTLE TRIGGER 4 RIGHT CONTROL HANDLE 5 BLADE 6 NYLON STRING HEAD 7 STOP SWITCH 8 CHOKE 9 STARTER HANDLE 10 HARNESS RING 1 SPARK PLUG 2 AIR FILTER COVER 3 FUEL TANK CAP 4 MUFFLER SHIELD 5 ENGINE SHAFT JOINT 6 DELTA HANDLE 7 REAR CONTROL GRIP 8 SAFETY GUARD 19 SAFETY LEVER 20 SAFETY POLE GUARD 21 STRING CUTTER BLADE 22 NYLON STRING HEAD GUARD EXTENSION 3 BLADE GUARD 4 ATTACHMENT 5 LOCKING PIN 6 SHAFT ATTACHMENT JOINT 27 LOCKING PIN HOUSINGS 28 JOINT KNOB NN S WH bh Italia SpA 23868 Valmadrera LC IT Model IN INML Serial Number 5 Type Engine Code BC050 BC 34 03_A 005 JO MMIII T 53908336 Example of identification label LEGEND 1 Guarante
12. a damaged blade replace with a new one Kickback can also occur when cutting with any type of blade in the hazardous zone see 13 Do not let the blade cut in the risk sector to prevent kickback Precautions for operating a split shaft machine 17 If your machine is a split shaft model that is to say composed of a power unit 1 and an attachment 2 you must furthermore conform to the following rules Never turn on the machine without an attachment cor rectly fitted Before every start check the attachment shaft joint and the attachment to be assembled correcty and in excellent conditions This manual is meant to be the manual of the power unit the manual of the string head grass blade attachment and moreover if not explicitly stated otherways it refers to the two units as already assembled in ther proper way see chapter E6 attachments fitting removal When using other attachments carefully read their instruc tion manual and make sure you understand them before using This machines allows the fitting of the following attachments only UNIVERSAL OUTDOOR ACCES SORIES Hedge Cutter Attachment C Description of the safety devices on the machine ABBE Safety lever Never use the machine with its Safety lever pressed with adhesive tape string or other This device serves to prevent accidentally press ing the throttle trigger fig A no 3 In fact the trigger fig A no 3 can only be pressed if the safety lever is
13. ce the fire hazard especially in the presence of inflammable materials or gas Start the engine at a dis tance from the filling site and far away from any fuel tanks at least 3 meters When filling the fuel tank dry any spilled fuel Never add fuel in the tank when the engine is running or hot to avoid the risk of fire let the engine cool off before fill ing the tank Fill the tank outdoor far from flames or sparks Do not take the cap off the tank with the engine running Open the cap on the tank carefully to eliminate any excess pressure After fueling close the cap tightly Take care not to spill any fuel The fumes produced by the fuel can cause an explosion or fire Gasoline is highly inflammable before going near any type of fuel put out your cigarette pipe or cigar Do not smoke or take sources of heat or sparks near the fuel Never refuel near or over inflammable objects dry leaves etc Kickback Machines equipped with blades may produce a violent kickback on contact with solid bodies The force of the kickback can cause the operator to lose con trol of the machine The blade is capable of amputating arms and legs Always work with a sharp blade A blade with worn teeth can create problems in cutting and can cause KICKBACK that is a violent thrust on the front of the machine caused by the impact of the blade against wood or solid foreign bodies This kickback can cause loss of control of the machine Never sharpen
14. ch der Hersteller das Recht vor technische Anderungen ohne vorherigen Hinweis durchzuf hren La Maison se r serve la possibilit de changer des caract ristiques et des donn es de ce manuel nimporte quel moment et sans pr avis Door konstante produkt ontwikkeling behoud de fabrikant zich het recht voor om rechnische specificaties zoals vermeld in deze handleiding te veranderen zonder biervan vooraf bericht te geven Produsenten forbeholder seg all rett og mulighet til forandre tekniske detaljer i denne manualen uten forh ndsvarsel Jatkuvan tuotteen parannusohjelman t hden valmistaja pid tt oikeuden vaihtaa ilman ennakkovaroitusta t ss ohjekirjasessa mainittuja teknisi yksityiskohtia Tilverkaren reserverar sig r tten att ndra fakta och uppgifter ur handboken utan f rvarning Producenten forbeholder sig ret til ndringer hvad ang r karakteristika og data i n rv rende instruktion n r som helst og uden varsel La firma productora se reserva la posibilidad de cambiar las caracteristicas y datos del presente manual en cualquier momento y sin previo aviso Acasa productora se reserva a possibilidade de variar caracter sticas e dados do presente manual em qualquer momento e sen aviso previo La casa produttrice si riserva la possibilita di variare caratteristiche e dati del presente manuale in qualunque momento e senza preavviso A gy rt c g fenntartja a jogot arra hogy a hasznalati utasita
15. clothing Do not wear jewelry that could get caught in moving parts of the machine e Safety boots with non slip sole crush resistant toe cap and protection against cuts do not wear sandals or work barefoot e Sturdy gloves resistant to cuts and vibrations e Safety visor or protective goggles Remove the protec tive film if any e Hearing protection e Hard hat if there is any risk of falling objects Health precautions Avoid prolonged use Noise and vibrations may be dangerous Prolonged use of the machine or other equioment expose the operator to vibrations that can cause the White Finger Syndrome Syndrome of Raynaud This could reduce the sensitivity of the hands in distinguishing different temperatures and cause a general numbness The operator should therefore check the con ditions of the hands and fingers if the machine is used continuously or regularly If one of the symptoms should appear consult a doctor immediately Prolonged use of the machine or other equipment can cause discomfort stress fatigue hearing damage Wear suitable hearing protection when using the machine Correct and scrupu lous maintenance can also helo to protect you further from the risk of noise and vibration 7 Avoid contact of the eyes and skin with any oil or fuel Do not inhale the gasoline fumes as they are toxic Do not start or run the motor in closed or poorly ventilated places The exhaust fumes are poisonous to breathe and can be a
16. cnu INSTRUKCJA OBS UGI Gwarancja traci wa no w przypadku u ywania urz dzenia do cel w innych ni wymienione w instrukcji obstugi Prosimy o uwa ne przeczytanie instrukcji oraz o stoowanie sie do zalece i wskaz wek w niej zawartych NAVOD NA OBSLUHU D le it inform cia Pred pou it m stroja si starostlivo pre tajte tento n vod na obsluhu a uistite sa ze ste mu d kladne porozumeli N vod starostlivo uschovajte pre potrebu v bud cnosti NMHCTPYKUNN BAXKHbIE CBEQEHMA BHUMaTenbHO NpOYnTaTb MHCTpYKUMN M SDOUIO nX NOHATb Nepe TeM Kak NONb30BaTbCA 6NOKOM XpaHnTb MHCTDNKUMM ANA nanbHe uiWx KOHCYNbTALM KASUTUSJUHEND T HTIS INFORMATSIOON Lugege kasutusjuhend enne seadme kasutamist kindlasti p hjalikult l bi ning veenduge et olete k igest t pselt aru saanud ROKASGRAMATA SVARIGA INFORMACIJA Pirms ierices izmantodanas Jzmanigi izlasiet rokasgramatu un parliecinieties ka jus abi saprotat tas saturu Saglabajiet rokasgramatu lal n kotng b tu iespcjams atsvaidzinat jasu zinadanas KULLANMA KYLAVUZU ONEMLI TALIMATLAR Buradakt bilgileri dikkatiice okuyunuz ve aleti kullanmaya ba lamadan nce t m talimatlar n tarafinizdan antagimis oldugundan emin olunuz Gerektigi zaman basvurabilmeniz i in saklayiniz Due to a constant product improvement programme the factory reserves the right to modify technical details mentioned in this manual without prior notice Im Sinne des Fortschritts beh lt si
17. cutting diame ter For correct assembly see the illustration on the cover and perform the following sequence of steps Insert the extension B on the safety guard A at the reference notches C and fasten with the screws D then apply the string cutter blade L with the cutting edge facing towards the outside of the shield and fasten it with the screw E Make sure the screws are tightened all the way E and are not loosened by the vibrations If necessary tighten them again CAUTION If you are using the grass cut ting blade remove the extension B on the guard A ENGLISH 5 E4 Assembly disassembly of line cutter head A BHOD Apply the nylon string head as shown in the illus tration 1 Upper plate 2 Protection not supplied with all models 3 Nylon string head Tighten by turning counterclockwise As you tighten hold the nylon string head and plate still and insert the wrench or screwdriver supplied in the holes in the plate and gearbox first turn the plate until the two holes match E5 Assembly disassembly of grass cutter blade A BHD Apply the blade as shown in the illustration a Upper plate with blade centering b Protection not supplied with all models c Blade with word ing and direction arrow facing upward d Lower plate e Fixed cup f Blade fastening nut CAUTION Do not use the nylon string head guard extension with metal blades E6 Attachments fitting removal for split shaft
18. e blade is capable of amputating arms and legs CAUTION Danger of serious leg injuries Take scrupulous care to fol low the instructions in the manual CAUTION The cutting parts and muffler may get very hot and cause burns Wait a w minutes before touching them RG Make sure the machine is correctly assembled and all its parts are working properly Make sure the screws are all in place and securely tightened Check operation of the accelerator control block and make sure there is no leakage of fuel Check that the cutting tool does not move with the motor running at idle soeed Make sure the transmission pipe is properly fastened to the motor joint and the line cutter head or blade are correctly fas tened with the screw fastening the blade fully tightened Replace any accessories blades nylon string heads guards which show damage or cracks or appear excessively worn Have your Authorized Service Center replace any damaged parts For nylon string heads use only strings made of flexible material recom mended by the manufacturer For example you should never use metal wire because it could cause serious injuries to people property and animals An unsuitable string could break and turn into a very dangerous mis sile In mounting the cutting utensils follow the instruc tions in the chapter entitled Usable cutting tools and their installation on the machine ABSOLUTELY DO NOT USE THE BRUSH CUTTER IF THE SPECIFIC SAFETY
19. each accessory and take care not to let the blades come into contact with rocks metal parts etc The blade is sharp so be very careful when handling it even with the engine off Keep any other persons or animals away from the work zone minimum distance 15 meters Since there is a danger when you are working that the blade or nylon string head could throw out grass dirt rocks or for eign bodies when someone approaches switch the engine off or stop the blade or rotating head See section entitled Starting and stopping the engine Fasten your hair above shoulder length Start the machine in a flat place in a stable position making sure the cutting tool does not touch any obstacles Use the machine holding it to the nght of your body so that the exhaust fumes can escape freely without obstruction from your clothing While working grip the brush cutter firmly with both hands Stand in a stable position on your feet Keep the grips clean and dry Do not use the brush cutter while standing on a ladder or other unstable support You should always be able to control your balance Never use the machine under extreme weather conditions or in bad weather very low temperatures very hot humid climate fog rain wind etc Keep all parts of your body and clothing away from the blades during startup or when the engine is running During use keep the work zone in front of you Never cut walking backwards as you cannot see possible hazards D
20. ed noise level according to directive 2000 1 AE 2 Manufacturer s name and address 3 Year of manufacture 4 Product code 6 Model type 5 Serial no 7 CE marking of conformity 8 Displacement B Safety precautions Explanation of Symbols Warning Safety apparel Approved protective goggles or visor approved hard hat and hearing protection Read the instructions for the user carefully and make sure you under stand how all the controls work Safety apparel Approved gloves S 3 O D H EI Safety apparel Approved boots Do not smoke when refueling or using the machine Choke Danger of flying debris ENGLISH 1 Minimum safety distance 15m Stor Emergency stop Maximum shaft speed n min Use of the manual e Anyone who uses the machine should have read the entire manual with extreme care e All users should be familiar with the operations for use of the machine under absolutely safe conditions as described in this manual and should be instructed in the proper cutting techniques to use possibly by practical demonstration e Do not allow children or persons who are not familiar with these instructions and are not sufficiently trained to use the brush cutter Local regulations may specify an age limit for users e Keep this manual with the machine when selling or lending it to enable the future users to familiar ize themselves with the product and i
21. in a dry place After 25 hours of use Remove the filter as shown in the figure and clean it using a gentle jet of compressed air For more thorough cleansing you can wash it with soapy water After 50 hours of use Add some high speed gear grease in the gearbox through hole C Remove and clean the spark plug set the space between the electrode at 0 5 0 6 mm Replace if excessively encrusted In case of excessive encrustation check the carbu retor adjustment the percentage of oil in the fuel mixture and make sure the oil is of excellent quali ty and suitable for two stroke engines After 100 hours of use Replace the spark plug Every three months Contact your Service Center for a complete over haul replacement of the fuel filter and cleaning of the parts inside the machine This will reduce the possibility of unexpected problems and will ensure the good performance and long life of your machine Periods of prolonged disuse See Environmental information If you use the machine in an exceptionally dirty or dusty environment these operations should be carried out more often H2 Replacement of nylon string To replace the reel of string press both the release pawls indicated by the arrows remove the empty reel unroll any string left and rewind the new string Open the original package of string and insert the ends of the two strings in the eyelets on the reel then wind the strings com pletely on the reel in the
22. inde sahip tutar 2 Strokes engine totally synthetic oil or McCulloch oil 0 095 2 4mm 4 i 4 JI 197 5000mm 34 40 cc 531025001 538249155 Si ES 531024905 538249155 531024902 538249155 531024906 538249155 531024903 538249155 GB SUMMARY CHART TO IDENTIFY THE CORRECT GUARD NEEDED WITH DIFFERENT CUTTING ATTACHMENTS DE BERSICHTSTABELLE ZUR AUSWAHL DES RICHTI GEN SCHUTZBLECHES F R DIE EINZELNEN SCHNEIDWERKZEUGE TABLEAU RECAPITULATIF POUR LE CORRECT ACCOUPLEMENT LAME OU TETE FIL NYLON DEFENSE DE SECURITE OVERZICHTSTABEL OM TE BEPALEN WELKE BESCHERMKAP GEBRUIKT MOET WORDEN BIJ DE DIVERSE MAAI ONDERDELEN QD TABELL FOR KORREKT MONTERING AV TR D SPOLE SAGBLAD OG SPRUTSKJ RM SIKKER HETSV AERN TAULOKKO LEIKKAAVAN PAAN TURVASUOJUKSEN OIKEASTA YHDISTELMASTA SAMMANFATTANDE TABELL OVER KORREKT KOM BINATION AV SKARHUVUD SAKERHETSSKYDD Ga OVERSIGTSTABEL VEDR RENDE DEN KORREKTE SAMMENSAETNING AF KNIV OG BESKYTTELSESSKAERM TABLA PARA EL CORRECTO ACOPLAMIENTO DE LA CABEZA CORTANTE Y PROTECTOR DE SEGURIDAD GD TABELA DE RESUMO PARA A CORRETA APLICA O DA CABE A CORTANTE E DEFESA DE SEGURAN A TABELLA RIASSUNTIVA PER IL CORRETTO ABBINA MENTO TESTA TAGLIENTE DIFESA DI SICUREZZA QD SSZEFOGLAL T BL ZAT A NYIROFEJ SSZE LLIT SA BALESETV DELEM GR NEPIAH
23. ine The operations of filling the tank with the fuel mix ture should be carried out in Such a way as to avoid spilling fuel and contaminating the soil and environment Periods of prolonged disuse Always empty the fuel tank with the same precau tions used in filling it Disposal Do not dispose inappropriately of the machine when it is no longer usable Deliver it to an authorized organization for proper disposal in compliance with the regulations in force M Troubleshooting table Engine wil not start Check STOP switch is in the position l Control fuel level min 25 tank capacity Check air filter is clean Remove spark plug dry it clean it and adjust it and replace it if necessary Change fuel filter Contact your dealer Carefully follow the cutting accessory assembly instructions Check metal cutting accessory is The machine runs but does not cut well Engine runs badly or looses power when cutting sharp Otherwise contact your dealer e The engine continues to have problems contact your authorized supplier ENGLISH 8 N Declaration of conformity The undersigned authorized by Husqvarna Outdoor Products Italy S p A declares that the follow ing products model TYPE BC050 BCO60 starting from the serial numbers produced from 2006 on manufactured by Husqvarna Outdoor Products Italy S p A Valmadrera Italia comply with European Directive 98 37 EEC Machine Directive 93
24. kra dig om att du f rst r dem innan du anv nder utrustningen och spara dem f r framtida behov BRUGERHANDBOG VIGTIGE OPLYSNINGER L s instruktionerne omhyggeligt f r du bruger enheden og gemme til senere henvisning MANUAL DE INSTRUCCIONES INFORMACI N IMPORTANTE Lea atentamente las instruc ciones y aseg rese de entenderlas antes de utilizar esta apara to Conserve las instrucciones para la referencia en el futuro MANUAL DO OPERADOR INFORMA ES IMPORTANTES Queira ler cuidadosa mente estas instru es e tenha certeza de entend las antes de usar a serra e guarde para consulta futura IT HU GR CZ PL SK RU EE LV TR LIBRETTO D ISTRUZIONI INFORMAZIONI IMPORTANTI Leggere le istruzioni attentamente e capirle bene prima di usare utensile Conservare per ulteriore consultazione HASZNALATI UTMUTATO Jotallast v llalni csak rendeltet sszerUien haszn latba vett g pekre tudunk K rj hogy a g p haszn latba v tele el tt gondosan olvassa el a kezel si utas t sokat ETXEIPIAIO XEIPIZMOE xHMANTIKE gt NAHPOOOPIE Ara dote rpoosxrIx avTEc TIG o nyisc Xal OPOVTIOTE VA TIC XATAVO OETE AVTO TO unx vnpa xat MuAGETe TO yia va TO OULBOUAEUEOTE oto LEAAOV N VOD K POU V N D LE IT INFORMACE Ne za nete stroj pou vat p e t te si pros m velmi pozorn tyto instrukce a ujist te se e jste jim porozum li Uschovejte si tento n vod pro pou it i v budou
25. n string head will keep on rotating for a few seconds Hold the machine until all parts come to a standstill N B In an emergency the above mentioned delay in stopping may be shortened by touching blade parallel on the ground G Carburetor adjustment AHHH Your machine can be equipped with a low emis sion carburetor We recommend that you have any adjustment of the carburetor made exclusive ly by an authorized service center which disposes of special equipment for ensuring the best per formance with the lowest emissions To adjust the speed to the minimum turn the screw marked T as shown With the engine running and well warmed up turn the screw T gently clockwise until the engine rotates at regular speed stead noise without the cutting devices in motion If the cutting devices are moving turn the screw T gently counterclockwise until you obtain the prop er adjustment The correct minimum speed is shown in the instruction manual in the paragraph of technical data All the above adjustments should be made with the cutting devices correctly installed The warranty may be invalidated due to erro neous adjustments made by personnel not belonging to authorized service centers H Routine maintenance A FIEBRE EDID ili H1 After every use In order to avoid overheating the motor remove any dust and dirt from the slots on the cylinder cover and finds of the cylinder using a wooden scraper Store the machine
26. nstructions for safe use e All parts of the manual are equally important for the purpose of preventing injury to the operator or dam age to the machine To facilitate your reading section B is divided into parts that can be called up in the rest of the manual marked with the CAUTION symbol followed by the number of the corresponding para graph to concentrate your attention on the main safety procedures related to a particular situation Prior to use e Respect of the procedures described in this manual does not eliminate the risks of accidents but does reduce the probability of their occurring or the effect of the damage e f you have never used a brush cutter before prac tice using it for a while before actually starting to work with it e The operator or user is responsible for any damages to third parties or their property and for any dangers to which they may be subject e Do not use this machine for any other purpose than that for which it was designed using the proper cut ting devices as indicated in the instructions e Do not use the machine if you are tired in poor health or under the effects of alcohol or medication that could affect your reactions e Make sure you know how to stop the engine and blade if necessary see section entitled Starting and stopping the engine Inspect the machine carefully before every use in case of violent impact or signs of malfunction ENGLISH 2 Danger of kickback Th
27. o not put the machine down with the engine running Never leave the machine alone Never raise the brush cut ter above knee level during cutting Adjust the shaft fastening buckle so that the blade or line cutter head are parallel to the ground The connection point should be held in the original position so as to avoid unbalancing the shaft Precautions for carrying the machine Never carry the brush cutter even for short distances with the engine running Switch off the engine and carry it with the blade or nylon string head facing backward For your safety dur ing transport and storage always protect the blade with the guard supplied with the machine see Protection for transport When you trans port the brush cutter in a motor vehicle place it in a Stable fixed position so that no fuel leaks out We recommend emptying the fuel tank whenever you transport the machine Fire prevention precautions Never work with the brush cutter in the presence 14 of fire or spilled gasoline If you have spilt it on your self change your clothes at once Keep the machine clean by removing any grass cuttings leaves excess oil to reduce the fire hazard Engine exhaust fumes can get very ENGLISH 3 hot and may contain sparks Do not use the machine near inflammable material The muffler gets very hot during use and remains hot for some time after switching off the engine This also applies at idle speed Take every precau tion to redu
28. sban megadott adatokon s technikai tulaj donsagokon b rmikor s el zetes bejelent s n lk l v ltoztasson Adyw TDONDOUUOTOC OUVENO DC BEATIWONG TIPOIOVTWV TO EDNOOGTOOIO ETIIpU QGOETOI TOU OIKAIWLATOS VA TOOTTOTFOIE TIC TEXVIKES AETITONEPEIES Tou AVAMEPOVTAI OTO EYXEIDIOIO AUTO ytupi mponyoupevn EldoTroInan Vzhledem k pokra uj c m inovac m si vyrobce vyhrazuje pr vo minit technick hodnoty uveden v t to p ru ce bez predchoziho upozorneni W zwi zku z programem ci g ego ulepszania swoich wyrob w producent zastrzega sobie prawo do wprowadzania zmian w szczeg ach technicznych wymienionych w tej instrukcji bez uprzedniego zawiadomienia Instrukcja jest cz ci wyposa enia Proizvajalec si pridr uje pravico da spremeni zna ilnosti in podatke pri ujo ega priro nika v katerem koli trenutku in brez predhodnega obvestila KomMnaHua nponsBognTenb COXpaHAeT 3a coo IID3B0 N3MEHATb XADAKTEPMCTUKM H JAHHbIE B HaCTOALEM PYKOBOACTBE B DODOH MOMEHT n 063 npenBapMTeribHoro NZBELJEHMA Tootja j tab endale iguse muuta k esolevas kasutusjuhendis kirjeldatud omadusi ja andmeid suvalisel hetkel ja sellest eelnevalt ette teatamata izgatavot js saglab ties bas jebkur br d un bez br din juma main t aj rokasgr mat eso os datus un raksturl knes retici firma bu kullanma k lavuzunda yer alan zellik ve verilerin istedi i zamanda ve haber vermeksizin de i tirebilme hakk n kend
29. sphyxiating and even fatal Work zone Examine the work area and be careful of any haz ards such as roads driveways power lines hang ing tree limbs etc Take special care wnen working on sloping terrain Before use remove any rubbish from the work area such as rocks broken glass ropes metal parts cans bottles and any foreign body that could become entangled with rotating parts or be projected dangerously at a distance Take account of possible haz ards that may not be perceived because of the noise of the machine Make sure there is someone in the vicinity within safe calling distance in case of accident During use During use and for a few minutes after switching off the machine the gearbox and zone near the shaft on which the cutting device is fastened are very hot The muffler and its guard are very hot during use and after the engine has been switched off even with the engine run ning at minimum speed Contact can cause burns Do not touch these parts if they are still hot Twigs or grass may jam between the safety guard and the blade or nylon string head Never try to remove this material with the engine running and or the blade rotating Watch out for the rotating parts and hot surfaces of the machine Contact between the blades and any extraneous objects could cause serious injury to the operator or other people or animals in the vicinity and could also damage the machine Cut only the material recommended for
Download Pdf Manuals
Related Search