Husqvarna 1.610 Brush Cutter User Manual
Contents
1. Startup of cold engine F1 Stop switch A turned to Il opposite the STOP mark F2 Turn the fuel enrichment lever B to the closed position ENGLISH 6 F3 Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm C The diaphragm need not be completely filled Push the decompression valve D down if your models is fitted with one Pull the cord until the engine starts Let the motor run for a few seconds and accelerate This will automatically return the fuel enrichment lever to its original position AN The cutting devices are now rotating Startup of warm engine F1 STOP switch turned to I START Throttle trigger lever in minimum position released Enrichment lever B in original position F3 Repeat item F3 in the previous paragraph Stopping the engine F5 Turn the stop switch to O STOP After stopping the engine the rotating parts blade or nylon string head keep spinning by inertia for a few seconds Grip the machine firmly until they stop In case of emergency the above delay can be abbreviated by scraping the blade supporting cup parallel on the ground G Carburetor adjustment A DEI Your machine can De equipped with a low emis sion carburetor We recommend that you have any aqjustment of the carburetor made exclusive ly by an authorized service center which disposes of special equioment for ensuring the best per formance with the lowest emissions To2. ENGLISH 2 Danger of kickback The blade is capable of amputating arms and legs CAUTION Danger of serious leg injuries Take scrupulous care to fol low the instructions in the manual CAUTION The cutting parts and muffler may get very hot and cause burns Wait a w minutes before touching them w Inspect the machine carefully before every use in case of violent impact or signs of malfunction Make sure the machine is correctly assembled and all its parts are working properly Make sure the screws are all in place and securely tightened Check operation of the accelerator control block and make sure there is no leakage of fuel Check that the cutting tool does not move with the motor running at idle soeed Make sure the transmission pipe is properly fastened to the motor joint and the line cutter head or blade are correctly fas tened with the screw fastening the blade fully tightened Replace any accessories blades nylon string heads guards which show damage or cracks or appear excessively worn Have your Authorized Service Center replace any damaged parts For nylon string heads use only strings made of flexible material recom mended by the manufacturer For example you should never use metal wire because it could cause serious injuries to people property and animals An unsuitable string could break and turn into a very dangerous mis sile In mounting the cutting utensils follow the instruc tions in the ch
3. Lecco ITALY O Technical data Displacement CM BEE E 34 38 40 43 46 49 Bore iD aasan akak et a 38 40 40 41 43 44 OUO EDU sn Dassur Gan attr ree 30 32 32 32 32 32 Engine output KW UE 1 2 1 3 1 5 1 6 1 8 2 0 Maximum shaft rotation frequency Im 7 700 7 700 7 700 7 700 7 700 7 700 Rotation speed frequency of rotation of engine at maximum rotation frequency recommended for Shaft Im 12 100 12 100 12 100 12100 12 100 12 100 Engine speed at max power MIN EE 8 000 8 000 8 000 8 200 8 200 8 200 Minimum speed MIN nn easton nn 2 800 2 800 2 800 2 800 2 800 2 800 Maximum speed no load min n r 10 000 10 000 10 000 10 000 10 000 10 000 Beate ol EE 7 1 7 3 1 3 8 3PRO 7 7 8 7PRO 7 8 7PRO 7 8 7PRO Fuel tank capacity cm Ee be 1000 1000 1000 1000 1000 1000 Blade locking nut tightening torque NIM AA 17 17 17 17 17 17 Noise pressure at operator ear Lpav ABA ISO 7917 97 97 97 97 97 97 Measured sound power level Lwav ABA ISO 10884 113 113 113 113 113 113 Guaranteed noise level LWav ABA ISO 10884 cece 114 114 114 114 114 114 Vibrations level string head ISO 7916 M S max min 8 2 1 6 8 2 1 7 8 2 1 7 10 55 1 8 12 5 1 06 12 5 1 06 Vibrations level blade ISO 7916 M S max min 8 2 1 6 8 2 1 7 8 2 1 7 16 38 1 8 17 79 1 06 17 79 1
4. tic shield will cut the nylon string to opti mum length a string that is too long reduces the rotation speed of the engine and interferes with cutting efficiency as well as increasing the risk of injury The extension B should be installed only for use with the nylon string head with the aid of the string cutter blade L that regulates the length of the string and thus the cutting diameter For cor rect assembly see the illustration on the cover and perform the following sequence of steps Insert the extension B on the safety guard A at the reference notches C and fasten with the screws D then apply the string cutter blade L and fasten it with the screw E Make sure the screws are tightened all the way E and are not loosened by the vibrations If necessary tighten them again E5 Assembly disassembly of line cutter head A BHD Apply the nylon string head as shown in the illus tration 1 Upper plate 2 Nylon string head Tighten by turning counterclockwise As you tighten hold the nylon string head and plate still and insert the wrench or screwdriver supplied in the holes in the plate and gearbox first turn the plate until the two holes match E6 Assembly disassembly of grass cutter blade ABHHD Do not use the nylon string head guard extension H with metal blades Assemble blade as illustrated a Flange guard b Upper cap with blade centering c Blade with text and directional arrow facing
5. 06 ENGLISH 10
6. blade rotating Watch out for the rotating parts and hot surfaces of the machine Contact between the blades and any extraneous objects could cause serious injury to the operator or other people or animals in the vicinity and could also damage the machine Cut only the material recommended for each accessory and take care not to let the blades come into contact with rocks metal parts etc The blade is sharp so be very careful when handling it even with the engine off Keep any other persons or animals away from the work zone minimum distance 15 meters Since there is a danger when you are working that the blade or nylon string head could throw out grass dirt rocks or for eign bodies when someone approaches switch the engine off or stop the blade or rotating head see section entitled Starting and stopping the engine Fasten your hair above shoulder length Start the machine in a flat place in a stable position making sure the cutting tool does not touch any obstacles Use the machine holding it to the nght of your body so that the exhaust fumes can escape freely without obstruction from your clothing While working grip the brush cutter firmly with both hands Stand in a stable position on your feet Keep the grips clean and dry Do not use the brush cutter while standing on a ladder or other unstable support You should always be able to control your balance Never use the machine under extreme weather conditions or in bad weathe
7. cannot tum over in a stable position with the motor off the switch turned to O STOR the cutting tool stopped and wearing adequate protective gloves Apparel Dress suitably for the job wear approved personal protection gear e Closely fitting protective clothing do not wear shorts or loose clothing Do not wear jewelry that could get caught in moving parts of the machine e Safety boots with non slip sole crush resistant toe cap and protection against cuts do not wear sandals or work barefoot e Sturdy gloves resistant to cuts and vibrations e Safety visor or protective goggles Remove the protec tive film if any e Hearing protection e Hard hat if there is any risk of falling objects Health precautions Avoid prolonged use Noise and vibrations may be dangerous Prolonged use of the machine or other equioment expose the operator to vibrations that can cause the White Finger Syndrome Syndrome of Raynaud This could reduce the sensitivity of the hands in distinguishing different temperatures and cause a general numbness The operator should therefore check the con ditions of the hands and fingers if the machine is used continuously or regularly If one of the symptoms should appear consult a doctor immediately Prolonged use of the machine or other equipment can cause discomfort stress fatigue hearing damage Wear suitable hearing protection when using the machine Correct and scrupu lous maintenance can also hel
8. kra dig om att du f rst r dem innan du anv nder utrustningen och spara dem f r framtida behov BRUGERHANDBOG VIGTIGE OPLYSNINGER L s instruktionerne omhyggeligt f r du bruger enheden og gemme til senere henvisning MANUAL DE INSTRUCCIONES INFORMACI N IMPORTANTE Lea atentamente las instruc ciones y aseg rese de entenderlas antes de utilizar esta apara to Conserve las instrucciones para la referencia en el futuro MANUAL DO OPERADOR INFORMA ES IMPORTANTES Queira ler cuidadosa mente estas instru es e tenha certeza de entend las antes de usar a serra e guarde para consulta futura IT HU GR CZ PE SK RU EE LV TR LIBRETTO D ISTRUZIONI INFORMAZIONI IMPORTANTI Leggere le istruzioni attentamente e capirle bene prima di usare utensile Conservare per ulteriore consultazione HASZNALATI UTMUTATO Jotallast v llalni csak rendeltet sszerUien haszn latba vett g pekre tudunk K rj hogy a g p haszn latba v tele el tt gondosan olvassa el a kezel si utas t sokat ETXEIPIAIO XEIPIZMOE xHMANTIKE gt NAHPOOOPIE AtaBdote rpoosxrIx avTEc TIG o nyisc Xal OPOVTIOTE VA TIC XATAVO OETE AVTO To unx dvnuq xat MuAGETe TO yia va to OULBOUAEUEOTE oto LEAAOV N VOD K POU V N D LE IT INFORMACE Ne za nete stroj pou vat p e t te si pros m velmi pozorn tyto instrukce a ujist te se e jste jim porozum li Uschovejte si tento n vod pro pou it i v budouc
9. quali ty and suitable for two stroke engines After 100 hours of use Replace the spark plug Every three months Contact your Service Center for a complete over haul replacement of the fuel filter and cleaning of the parts inside the machine This will reduce the possibility of unexpected problems and will ensure the good performance and long life of your machine Periods of prolonged disuse See Environmental information If you use the machine in an exceptionally dirty or dusty environment these operations should be carried out more often H2 Replacement of nylon string To replace the reel of string press both the release pawls indicated by the arrows remove the empty reel unroll any string left and rewind the new string Open the original package of string and insert the ends of the two strings in the eyelets on the reel then wind the strings com pletely on the reel in the same direction and fas ten the end of each string in the 2 opposite grooves Replace the reel in its housing and thread the ends of the strings in their bushings Pull each string so that about 15 cm comes out on each side Reassemble the nylon string head as shown fig H5 If the reel becomes excessive ly worn replace it with a whole new reel ENGLISH 7 I Techniques for use Apgogoggg 0 2 i i Cutting techniques During the cutting operations keep the engine running at high speed After every cutting stage decelerate the engi
10. the fire hazard Engine exhaust fumes can get very hot and may contain sparks Do not use the machine near inflammable material The muffler gets very hot during use and remains hot for some time after switching off the engine This also applies at idle speed Take every precau tion to reduce the fire hazard especially in the presence of inflammable materials or gas Start the engine at a dis tance from the filling site and far away from any fuel tanks at least 3 meters When filling the fuel tank dry any spilled fuel Never add fuel in the tank when the engine is running or hot to avoid the risk of fire let the engine cool off before fill ing the tank Fill the tank outdoor far from flames or sparks Do not take the cap off the tank with the engine running Open the cap on the tank carefully to eliminate any excess pressure After fueling close the cap tightly Take care not to spill any fuel The fumes produced by the fuel can cause an explosion or fire Gasoline is highly inflammable before going near any type of fuel put out your cigarette pipe or cigar Do not smoke or take sources of heat or sparks near the fuel Never refuel near or over inflammable objects dry leaves etc Kickback Machines equipped with blades may produce a violent kickback on contact with solid bodies The force of the kickback can cause the operator to lose con trol of the machine The blade is capable of amputating arms and legs Always work
11. 90 and fully synthetic oil specific for two speed engines that use unleaded gasoline in the propor tions indicated in the table on the cover fig D Control the specifications of the oil shown on the package the use of oil lacking the specifications expressly indicated in this manual could cause serious damage to the engine To obtain the best mixture pour the oil into an approved container first followed by the gasoline and shake the container well every time you take fuel out of it The characteristics of the mixture tend to deterio rate in time so you should only prepare as much mixture as you are going to need the use of deteriorated fuel can seriously damage the engine Filling the tank A DE Clean the area around the fuel cap before remov ing it to prevent any impurities from contaminat ing the fuel Take the cap off the fuel container carefully Unscrew the cap on the fuel tank and fill it with the necessary quality using a funnel During use to prevent problems in starting the engine again we strongly recommend that you avoid letting the fuel run out in the tank Fuel storage A DE Store the fuel in a cool well ventilated place in an approved fuel storage container Never store the engine with fuel in the tank in a poorly ventilated place where the fumes produced by the gasoline could propagate and reach a fire candle burner or furnace pilot light water heater dryer etc Never store excessiv
12. Husqvarna Outdoor Products Italia SpA Via Como 72 23868 Valmadrera LC ITALIA Phone 39 0341 203111 Fax 39 0341 581671 PN 249957 REV 00 10 06 GB DE FR NL NO FI SE DK ES PT INSTRUCTION MANUAL IMPORTANT INFORMATION Please read these instructions care fully and make sure you understand them before using this unit Retain these instructions for future reference BETRIEBSANWEISUNG WICHTIGE INFORMATION Lesen Sie diese Hinweise zur Handha bung des Gerats aufmerk sam durch Verwenden Sie es erst wenn Sie sicher sind da Sie alle Anweisungen verstanden haben und gut aufbewahren MANUEL D INSTRUCTIONS RENSEIGNEMENTS IMPORTANTS Avant d utiliser cet appareil veuillez lire aten tivement les instructions et assurez vous de les avoir com prises Conservez les instructions pour r f rence ult rieure HANDLEIDING BELANGRIJKE IMPORTANTS Lees deze handleiding aan dachtig en zorg dat u ailes begrijot alvorens de kettingzaag te gebrulken en be waar ze voor toekomstige raadpleging BRUKERHANDBOK VIKTIG INFORMASJON Les disse anvisningene n ye og forsikre deg om at du forstar dem for du bruker enheten og oppbevar dem for sen ere bruk OHJEKIRJA T RKE TIETOA Lue n m ohjeet huolellisesti ja varmista ett olet ymm rt nyt ne ennen kuin alat k ytt t t laitetta ja s ilyt my hemp tarvetta varten BRUKSANVISNING VIKTIG INFORMATION L s instruktionerna noggrant och f rs
13. NTE Y PROTECTOR DE SEGURIDAD TABELA DE RESUMO PARA A CORRETA APLICA O DA CABE A CORTANTE E DEFESA DE SEGURAN A TABELLA RIASSUNTIVA PER IL CORRETTO ABBINA MENTO TESTA TAGLIENTE DIFESA DI SICUREZZA OSSZEFOGLALO TABLAZAT A NYIROFEJ OSSZEALLITASA BALESETVEDELEM GR NEPIAHMTIKO2 MINAKA TIA THN EIIZHMANZH TOY KATAAAHAOY MPOOYAAKTHPA ME AIAQOPA KONTIKA E APTHMATA SHRNUJ C TABULKA PRO SPR VNOU KOMBINACI REZNA HLAVA BEZPECNOSTNI OCHRANA G TABELA ZBIORCZA POPRAWNEGO ZESTAWIENIA G OWICY TNACEJ OS ONY ZABEZPIECZAJ CEJ Q TABELA POVZETEK ZA PRAVILNO POVEZAVO GLAVA ZASCITA QD O530PHAA TABHVLIA ANA NPABUNbHOrO COYETAHMA PE UE OJIOBKI NPEAOXPAHUTESIbHOrO YCTPOUCTBA B KOKKUV TLIK TABEL TRIMMIPEA JA SELLE KAITSME KORREKTSEKS MONTEERIMISEKS GD NOSL GUMA TABULA PAREIZAI GRIE ANAS _ GALVINAS UN DRO BAS AIZSARGA SAVIENOSANAI q 20GRU BIR G Y M EKL N ZETLEY C TABELA KES C KAFA EMN YET KORUNMASI A General description 1 ENGINE 4 2 2 SHAFT alia r 23868 d LC IT ao GRIP Puc IML Serial Number Cabrio34SB_ 953900699 03 53908336 4 5 6 NYLON STRING HEAD 6 Type Engine Code 7 STOP SWITCH BC050 BC_34 03_A 8 FUEL ENRICHMENT LEVER 8 9 STARTER HANDLE Year 2005 10 HARNESS RING 1 3 11 SPARK PLUG 12 AIR FILIER COVER e FUEL TANK CAP TE Example of identification label 15 RIGHT CONTROL HANDLE 16 DELTA HANDLE LEGEND 17 SAFETY LEVER 1 Guaranteed
14. adjust the speed to the minimum turn the screw marked T as shown With the engine running and well warmed up turn the screw T gently clockwise until the engine rotates at regular speed stead noise without the cutting devices in motion If the cutting devices are moving turn the screw T gently counterclockwise until you obtain the prop er adjustment The correct minimum speed is shown in the instruction manual in the paragraph of technical data All the above adjustments should be made with the cutting devices correctly installed The warranty may be invalidated due to erro neous adjustments made by personnel not belonging to authorized service centers H Routine maintenance A BBEOBEED H1 After every use In order to avoid overheating the motor remove any dust and dirt from the slots on the cylinder cover and finds of the cylinder using a wooden scraper Store the machine in a dry place After 25 hours of use Remove the filter as shown in the figure and clean it using a gentle jet of compressed air For more thor ough cleansing you can wash it with soapy water After 50 hours of use Add some high speed gear grease in the gearbox through hole C Remove and clean the spark plug set the space between the electrode at 0 5 0 6 mm Replace if excessively encrusted In case of excessive encrustation check the carbu retor adjustment the percentage of oil in the fuel mixture and make sure the oil is of excellent
15. apter entitled Usable cutting tools and their installation on the machine ABSOLUTELY DO NOT USE THE BRUSH CUTTER IF THE SPECIFIC SAFETY GUARD FOR THE CUTTING DEVICE IN USE IS NOT SECURELY FASTENED see chapter Assembly disassembly Failure to follow this rule can expose you to serious danger such as e possible contact with rotating and cutting parts e possible contact with flying debris Never use a brush cutter without its safety pole guard correctly in place Only use blades or nylon string heads clearly marked with a maximum speed of at least 10 500 min IF A METAL 24 80 TOOTH BLADE A SAW TOOTH BLADE IS USED A DOUBLE SHOULDER HARNESS AND A SAFETY GUARD PROTECTION MUST ALSO BE USED AS MARKED IN THE SUMMARY CHART Use only original or approved accessories and spare parts which you can purchase from our offi cial distributors The use of other accessories and spare parts increases the danger of injury and in this case the manufacturer has no liability for damage to persons or property Never attempt to use the machine if it is incom plete defective or has been altered by anyone other than an Authorized Service Center The risk of accidents increases considerably if maintenance is not carried our regularly in a professional way In case of doubt contact an authorized service center All operations of maintenance assembly disassem bly and fueling should be done with the machine on a flat solid surface so that the motor
16. e precau tions used in filling it Disposal Do not dispose inappropriately of the machine when it is no longer usable Deliver it to an authorized organization for proper disposal in compliance with the regulations in force M Troubleshooting table Engine runs badly The machine el or looses power runs but does when cutting not cut well Check STOP switch is in the posi tion l Control fuel level min 25 tank Capacity Check air filter is clean Remove spark plug dry it clean it and adjust it and replace it if nec essary Change fuel filter Contact your dealer Carefully follow the cutting acces sory assembly instructions Check metal cutting accessory is sharp Otherwise contact your dealer The engine continues to have problems contact your authorized supplier ENGLISH 9 N Declaration of conformity The undersigned authorized by Husqvarna Outdoor Products Italia SpA declares that the following products model TYPE BC010A BCO10B starting from the serial numbers produced from 2006 on manufactured by Husqvarna Outdoor Products Italia SpA Valmadrera Italia comply with European Directive 98 387 EEC Machine Directive 93 68 EEC EEC Marking Directive A 89 3836 EEC Electromagnetic Compatibility Directive directive 2000 14 EEC Enclosure V Fo Di Valmadrera 15 10 06 Giuseppe Todero Technical Manager Husqvarna Outdoor Products Italia SpA Via Como 72 23868 Valmadrera
17. e quantities of fuel E Assembly disassembly E1 Delta grip ABH For your safety fasten the delta handle in front of the label placed on the shaft at a distance of at least 18 cm from the rear grip The handle should be fastened in a comfortable working position If you are using sawtooth blades the grip distance should be moved by at least 42 cm The safety pole guard should be mounted using the acces sories supplied and in the configuration shown in the figure in contact with the delta handle E2 Double handled grip A The grip A can be adjusted to suit the needs of the operator by moving it forward or backward Loosen the knob place the handle in the desired position then tighten the knob again CAUTION The handle assembly A can be folded parallel to the transmission shaft to facilitate transport and storage of the machine Loosen the knob turn the support by 90 clock wise fold the handle A in the desired position and tighten the knob E3 Double Handle B Adjust and secure double hand clamp by tighten ing the screws E4 Fitting guard on line cutter head and grass cutting blade ABH Fit the safety guard A against the gearbox I position the lower clamp G in the housing under the shield and the upper clamp F over the shaft Insert and tighten the screws H ENGLISH 5 Safety guard extension exclusively for use with nylon string head The string cutting blade housed in the plas
18. er use a machine with the blade cover Still on ENGLISH 4 The guard covers the sharp extremities of the blade when the machine is in the resting position for transport or storage Safety guard ABBHHD This very important safety device fig A no 19 prevents any objects that come into contact with the cutting device or the grass itself from flying up and striking the operator Safety pole guard ABBE This device fastened to the machine ensures a minimum distance between the operator and the cutting device during use and prevents the machine from striking and injuring the operator if the blade hits a hard surface fig A no 18 Muffler A BBHEBROERHE The muffler serves to reduce the noise level to a minimum and to route the exhaust fumes pro duced by the combustion engine away from the operator Harness CAUTION It is very important to famil iarize yourself with the release mecha nism In case of emergency you need to be able to release the machine quickly The harness is equipped with a fasten release mechanism The harness enables the operator to support the machine during use see Safety pre cautions B 7 D Fuel Mixture Preparation of the mixture AN HEIE Do not use any other type of fuel than the type recommended in this manual This machine is equipped with a two stroke engine and should therefore be fueled with a mixture of unleaded gasoline with a minimum octane rating
19. h der Hersteller das Recht vor technische Anderungen ohne vorherigen Hinweis durchzuf hren La Maison se reserve la possibilit de changer des caract ristiques et des donn es de ce manuel a nimporte quel moment et sans pr avis Door konstante produkt ontwikkeling behoud de fabrikant zich het recht voor om rechnische specificaties zoals vermeld in deze handleiding te veranderen zonder biervan vooraf bericht te geven Produsenten forbeholder seg all rett og mulighet til forandre tekniske detaljer i denne manualen uten forh ndsvarsel Jatkuvan tuotteen parannusohjelman t hden valmistaja pid tt oikeuden vaihtaa ilman ennakkovaroitusta t ss ohjekirjasessa mainittuja teknisi yksityiskohtia Tilverkaren reserverar sig r tten att ndra fakta och uppgifter ur handboken utan f rvarning Producenten forbeholder sig ret til ndringer hvad ang r karakteristika og data i n rv rende instruktion n r som helst og uden varsel La firma productora se reserva la posibilidad de cambiar las caracteristicas y datos del presente manual en cualquier momento y sin previo aviso Acasa productora se reserva a possibilidade de variar caracter sticas e dados do presente manual em qualquer momento e sen aviso previo La casa produttrice si riserva la possibilita di variare caratteristiche e dati del presente manuale in qualunque momento e senza preavviso A gy rt c g fenntartja a jogot arra hogy a hasznalati utasitasba
20. motions from side to side maintaining the blade parallel to the ground During the right to left swing the grass is cut while the backswing must be made without using the blade KICKBACK can occur when cutting is done with the risk sector of the blade we recommend cut ting with the rest of the blade Take care that the cup supporting the blade just grazes the ground This will prevent the blade from touching the ground Use of sawtooth blade ABBE Do not attempt to cut trees with a larger than recommended diameter to prevent the risk of kickback or damage to the blade The sawtooth blade serves to cut bushes and small trees with maximum diameter of seven centimeters Rest the left side of the special shield on the trunk while cutting to limit the risk of losing control of the machine L Environmental information This section contains information useful for main taining the characteristics of eco compatibility included in the origin design of the machine and as regards proper use and disposal of oil and fuel Design In the design stage care was taken to develop an engine with reduced consumption and low emis sions of noise and pollutant exhaust fumes Use of machine The operations of filling the tank with the fuel mix ENGLISH 8 ture should be carried out in such a way as to avoid spilling fuel and contaminating the soil and environment Periods of prolonged disuse Always empty the fuel tank with the sam
21. n megadott adatokon s technikai tulaj donsagokon b rmikor s el zetes bejelent s n lk l v ltoztasson Adyw TDONDOUUOTOC OUVENO DC BEATIWONG T DOI VTU V TO EDNOOGTOOIO ETIIpU QGOETOI TOU OIKAIWLATOS VA TpOTIOTIOIE TI TEXVIKES AETITONEPEIES Tou AVAMEPOVTAI OTO EYXEIDIOIO AUTO ytupi mponyoupevn EldoTroInan Vzhledem k pokra uj c m inovac m si vyrobce v hrazuje pr vo minit technick hodnoty uveden v t to p ru ce bez predchoziho upozorneni W zwi zku z programem ci g ego ulepszania swoich wyrob w producent zastrzega sobie prawo do wprowadzania zmian w szczeg ach technicznych wymienionych w tej instrukcji bez uprzedniego zawiadomienia Instrukcja jest cz ci wyposa enia Proizvajalec si pridr uje pravico da spremeni zna ilnosti in podatke pri ujo ega priro nika v katerem koli trenutku in brez predhodnega obvestila KomMnaHua nponsBognTenb COXpaHAeT 3a coo IID3B0 N3MEHATb XADAKTEPMCTUKM H JAHHbIE B HaCTOALEM PYKOBOACTBE B DODOH MOMEHT n 063 npenBapMTeribHoro NZBELJEHMA Tootja j tab endale iguse muuta k esolevas kasutusjuhendis kirjeldatud omadusi ja andmeid suvalisel hetkel ja sellest eelnevalt ette teatamata izgatavot js saglab ties bas jebkur br d un bez br din juma main t aj rokasgr mat eso os datus un raksturl knes retici firma bu kullanma k lavuzunda yer alan zellik ve verilerin istedi i zamanda ve haber vermeksizin de i tirebilme hakk n ke
22. ndinde sahip tutar 2 Strokes engine totally synthetic oil or McCulloch oil 34 38 40cc 43 46 49 cc 531025002 538248960 34 38 40 cc 531025002 938248959 531024905 538248960 531024902 538248960 531024905 538248959 531024902 938248959 531024906 538248960 531024906 538248959 538036713 538248960 538036713 538248959 538040998 538242475 538240553 538240902 538040998 538242475 538240553 538240902 538040953 538242475 538240553 538240902 538040953 538242475 538240553 538240902 GB SUMMARY CHART TO IDENTIFY THE CORRECT GUARD NEEDED WITH DIFFERENT CUTTING ATTACHMENTS B BERSICHTSTABELLE ZUR AUSWAHL DES RICHTI GEN SCHUTZBLECHES F R DIE EINZELNEN SCHNEIDWERKZEUGE TABLEAU RECAPITULATIF POUR LE CORRECT ACCOUPLEMENT LAME OU TETE FIL NYLON DEFENSE DE SECURITE OVERZICHTSTABEL OM TE BEPALEN WELKE BESCHERMKAP GEBRUIKT MOET WORDEN BIJ DE DIVERSE MAAI ONDERDELEN QD TABELL FOR KORREKT MONTERING AV TR D SPOLE SAGBLAD OG SPRUTSKJ RM SIKKER HETSV RN TAULOKKO LEIKKAAVAN P N TURVASUOJUKSEN OIKEASTA YHDISTELM ST SE SAMMANFATTANDE TABELL VER KORREKT KOM BINATION AV SKARHUVUD SAKERHETSSKYDD G OVERSIGTSTABEL VEDR RENDE DEN KORREKTE SAMMENS TNING AF KNIV OG BESKYTTELSESSK RM B TABLA PARA EL CORRECTO ACOPLAMIENTO DE LA CABEZA CORTA
23. ne to minimum speed as running it at top speed without a load can damage the engine severely Wait until the engine is running at minimum speed before moving the machine from one section to another The machine is ideal to complete the work of the lawnmover In fact it can reach places where a normal lawnmower is unable to go Cutting and trimming grass borders with the nylon string head Cutting with the nylon string head is suitable for light jobs like trimming borders and cutting the grass around trees Mowing To prevent damage to your lawn or the cutting mechanism keep the string parallel to the ground but avoid contact with the terrain Trimming borders Angle the nylon string head keeping it a short dis tance from the ground Cut using the end of the string Do not press the string against the material to be cut I1 Drawing out the string During cutting the nylon string wears naturally causing an increase in the speed of the engine and a reduced cutting capacity When this hap pens to bring out more string bump the head against the ground release the throttle trigger to reduce the engine speed to less than 8000 rom Tap gently on the ground with the button A as shown in the figure and the string will come out automatically Accelerate again If the string does not come out make sure there is still some left and try again I3 Thinning grass with the grass cutter blade ABB The grass is cut with swinging
24. noise level according to 18 SAFETY POLE GUARD directive 2000 1 4 EC 19 STRING CUTTER BLADE 2 Manufacturer s name and address 20 NYLON STRING HEAD GUARD EXTENSION 3 Year of manufacture 21 BLADE GUARD 4 Product code 22 ENGINE SHAFT JOINT 5 Serial no 23 DECOMPRESSION VALVE 6 Model type 24 SAFETY GUARD 7 CE marking of conformity 8 Displacement B Safety precautions Explanation of Symbols Warning Safety apparel Approved boots Safety apparel Approved protective goggles or visor approved hard hat and hearing protection Do not smoke when refueling or using the machine Read the instructions for the user carefully and make sure you under stand how all the controls work Fuel enrichment starting aid Safety apparel Approved gloves A Danger of flying debris S 3 O D ENGLISH 1 Minimum safety distance 15m Stor Emergency stop Maximum shaft speed n min Use of the manual e Anyone who uses the machine should have read the entire manual with extreme care e All users should be familiar with the operations for use of the machine under absolutely safe conditions as described in this manual and should be instructed in the proper cutting techniques to use possibly by practical demonstration e Do not allow children or persons who are not familiar with these instructions and are not sufficiently trained to use the brush cutter Local regulations may specify an age limit for user
25. nu INSTRUKCJA OBS UGI Gwarancja traci wa no w przypadku u ywania urz dzenia do cel w innych ni wymienione w instrukcji obstugi Prosimy o uwa ne przeczytanie instrukcji oraz o stoowanie sie do zalece i wskaz wek w niej zawartych NAVOD NA OBSLUHU D le it inform cia Pred pou it m stroja si starostlivo pre tajte tento n vod na obsluhu a uistite sa Ze ste mu d kladne porozumeli N vod starostlivo uschovajte pre potrebu v bud cnosti NMHCTPYKUNN BAXKHbIE CBEQEHMA BHUMaTenbHO NpOYnTaTb MHCTpYKUMN VU SDOUIO nX NOHATb Nepe TeM Kak NONb30BaTbCA 6NOKOM XpaHnTb MHCTDNKUMM ANA nanbHe uiWx KOHCYNbTALM KASUTUSJUHEND T HTIS INFORMATSIOON Lugege kasutusjuhend enne seadme kasutamist kindlasti p hjalikult l bi ning veenduge et olete k igest t pselt aru saanud ROKASGRAMATA SVARIGA INFORMACIJA Pirms ierices izmantodanas Jzmanigi izlasiet rokasgramatu un parliecinieties ka jus abi saprotat tas saturu Saglabajiet rokasgramatu lal n kotng b tu iespcjams atsvaidzinat jasu zinadanas KULLANMA KYLAVUZU ONEMLI TALIMATLAR Buradakt bilgileri dikkatiice okuyunuz ve aleti kullanmaya ba lamadan nce t m talimatlar n tarafinizdan antagimis oldugundan emin olunuz Gerektigi zaman basvurabilmeniz i in saklayiniz Due to a constant product improvement programme the factory reserves the right to modify technical details mentioned in this manual without prior notice Im Sinne des Fortschritts behalt sic
26. o to protect you further from the risk of noise and vibration 7 Avoid contact of the eyes and skin with any oil or fuel Do not inhale the gasoline fumes as they are toxic Do not start or run the motor in closed or poorly ventilated places The exhaust fumes are poisonous to breathe and can be asphyxiating and even fatal Work zone Examine the work area and be careful of any haz ards such as roads driveways power lines hang ing tree limbs etc Take special care wnen working on sloping terrain Before use remove any rubbish from the work area such as rocks broken glass ropes metal parts cans bottles and any foreign body that could become entangled with rotating parts or be projected dangerously at a distance Take account of possible haz ards that may not be perceived because of the noise of the machine Make sure there is someone in the vicinity within safe calling distance in case of accident During use During use and for a few minutes after switching off the machine the gearbox and zone near the shaft on which the cutting device is fastened are very hot The muffler and its guard are very hot during use and after the engine has been switched off even with the engine run ning at minimum speed Contact can cause bums Do not touch these parts if they are still hot Twigs or grass may jam between the safety guard and the blade or nylon string head Never try to remove this material with the engine running and the
27. r very low temperatures very hot humid climate fog rain wind etc Keep all parts of your body and clothing away from the blades during startup or when the engine is running During use keep the work zone in front of you Never cut walking backwards as you cannot see possible hazards Do not put the machine down with the engine running Never leave the machine alone Never raise the brush cut ter above knee level during cutting Adjust the shaft fastening buckle so that the blade or line cutter head are parallel to the ground The connection point should be held in the original position so as to avoid unbalancing the shaft Precautions for carrying the machine Never carry the brush cutter even for short distances with the engine running Switch off the engine and carry it with the blade or nylon string head facing backward For your safety dur ing transport and storage always protect the blade with the guard supplied with the machine see Protection for transport When you trans port the brush cutter in a motor vehicle place it in a Stable fixed position so that no fuel leaks out We ENGLISH 3 recommend emptying the fuel tank whenever you transport the machine Fire prevention precautions Never work with the brush cutter in the presence of fire or spilled gasoline If you have spilt it on yourself change your clothes at once Keep the machine clean by removing any grass cuttings leaves excess oil to reduce
28. s e Keep this manual with the machine when selling or lending it to enable the future users to familiarize themselves with the product and instructions for safe use e All parts of the manual are equally important for the purpose of preventing injury to the operator or dam age to the machine To facilitate your reading section B is divided into parts that can be called up in the rest of the manual marked with the CAUTION symbol followed by the number of the corresponding para graph to concentrate your attention on the main safety procedures related to a particular situation Prior to use e Respect of the procedures described in this manual does not eliminate the risks of accidents but does reduce the probability of their occurring or the effect of the damage e f you have never used a brush cutter before practice using it for a while before actually starting to work with it e The operator or user is responsible for any damages to third parties or their property and for any dangers to which they may be subject e Do not use this machine for any other purpose than that for which it was designed using the proper cut ting devices as indicated in the instructions e Do not use the machine if you are tired in poor health or under the effects of alcohol or medication that could affect your reactions e Make sure you know how to stop the engine and blade if necessary see section entitled Starting and stopping the engine
29. upwards d Lower washer e Fixed mower gauge f Blade locking screw length mm 16 If you want to assemble the rotating mower gauge proceed as illustrated a Flange guard b Upper cap with blade centering c Blade with text and directional arrow facing upwards d Lower washer e Spacer f Rotating mower gauge g Blade locking screw length mm 34 5 Assembly of sawtooth blade and blade guard A BHD When using the sawtooth blade remove the guard for the line cutter head and grass cut ting blade and replace the flange guard A with the sawtooth blade guard H Saw tooth blades 24 80 tooth have a central base diametre of 20mm and there fore require the use of the appropriate size top flange to ensure a correct fit The part number is detailed in the cutting attachment summary chart For assembly see figures E7 E8 AN HDH RUE CAUTION Start the brush cutter in a flat place During startup stand in a stable position Make sure the blade or nylon strino head do not touch the ground or any obstacles CAUTIONI Grip the knob of the starter with one hand and hold the machine in a stable position with the other Take care not to wind the starter string around your hand and pull slowly until you encounter some resistance then pull the cord sharply and forcefully to start the engine when Do not pull the starter cord all the way and do not release it abruptly against the machine as this could damage it
30. with a sharp blade A blade with worn teeth can create problems in cutting and can cause KICKBACK that is a violent thrust on the front of the machine caused by the impact of the blade against wood or solid foreign bodies This kickback can cause loss of control of the machine Never sharpen a damaged blade replace with a new one Kickback can also occur when cutting with any type of blade in the hazardous zone see 13 Do not let the blade cut in the risk sector to prevent kickback C Description of the safety devices on the machine ABBE Safety lever Never use the machine with its Safety lever pressed with adhesive tape string or other This device serves to prevent accidentally press ing the throttle trigger fig A no 3 In fact the trigger fig A no 3 can only be pressed if the safety lever is pressed at the same time fig A no 17 By means of 2 separate springs upon releasing the grip the throttle trigger fig A no 3 and safety lever fig A no 17 return automatically to their original positions Antivibration device The machine is equipped with an antivibration device which serves to reduce the vibrations transmitted to the operator Engine stop device Turn the stop button Stop fig A no 7 to O STOP to stop the engine To make sure this but ton works properly start the engine and check that it stops when the Stop button is turned to the Stop position Protection for transport ABD Nev
Download Pdf Manuals
Related Search