Hunter Fan 90434 Fan User Manual
Contents
1. 2 Cover 44086 01 Figure 4 Figure 5 Figure 6 20101102 MOTOR ASSEMBLY 1 Grasp the Telescope Pole firmly and twist the Adjustment Knob Counter Clockwise to loosen Figure 7 2 Raise the Inner Pole and tighten the Adjustment Knob by twisting Clockwise until secure 3 Remove the Motor Knob 7 Motor Bolt 6 and Tilt Adjustment Knob 8 Loosen the screw above the Motor Knob 7 4 Set the Motor 5 on top of the Pole 3 Figure 8 and Secure using the Motor Bolt 6 and Knob 7 Retighten the screw above the motor knob in the slot to secure motor Figure 9 Note The Motor Bolt has a square cut on the inside of the head ensure this fits securely into the square hole in the Pole Do not overtighten the Motor Knob as this could make it difficult fo tilt the motor later After securing the motor 5 Screw in the Tilt Adjustment Knob 8 securely Figure 10 This Knob allows you to adjust the fans angle 2010 Hunter Fan Co 8 5 Motor gz 7 Motor Knob 8 Tilt Adjustment Knob 44086 01 Figure 7 6 Motor Bolt Figure 10 20101102 GRILL ASSEMBLY 1 Place the back grill against the motor housing 5 Figure 11 and line up the 4 tabs on the back of the grill 9 to the 4 screws holes on the front of the motor Caution Make sure the Handle on the back of the Back Grill is facing up 2 Attach the Back Grill 9 to the Motor 5 using the 4 Grill Mount Screws Figur2. 3 Carefully remove the fuse from the clips holding it on the top and bottom Figure 3 Warning Electrical Hazard Only replace with a fuse type and rating matching what was removed from the product 4 Gently push the fuse back into the pins that will hold it in place Note If the fuse is not seated properly the unit will not function 5 Slide the Door back over the fuse box in the plug 6 Plug the fan back in and resume use 2010 Hunter Fan Co 6 Figure 1 Figure 2 Figure 3 44086 01 20101102 UNPACKING As you unpack the fan save the carton and packing materials in case you want to move or ship the unit in the future Carefully remove all items from the box NOTE It is best to have someone hold the box while you lift the fan and the protective packaging out of the carton Make sure all shipping materials are removed from fan before operating BASE ASSEMBLY 1 Insert the Weight 1 into the Base Cover 2 Figure 3 2 Insert the base of the Telescoping Pole 3 into the top of the Base Cover 2 and attach to the Base Weight 1 by turning clockwise on Screw 4 in the center of the Weight 1 Figure 4 3 Turn the Base on ifs side and turn the handle of the Screw 4 on the bottom of the Weight until secure Figure 3 4 Tip the Base back upright Figure 5 2010 Hunter Fan Co 7 2 Base Cover 1 Base Weight 3 Telescope 4 Figure 3
3. Back Grill together Pull the Front Grill forn the back 4 The blade may be removed by loosening the screw holding it in place Grills and blades may be cleaned with mild soap and water only after they have been removed from the motor housing 5 Use a dry or slightly damp lint free cloth to clean the fan Use a soft slightly damp cloth to wipe the remaining fan parts DO NOT allow water or any other liquid to get into the motor housing or base Reassemble fan after blades and grills have dried completely DO NOT plug the fan into an electrical outlet until it has been fully reassembled 2010 Hunter Fan Co 12 7 NN NS 44086 01 Q 7 2 4 CX 20101102 7 lt 1 Problem Fan will not oscillate Solution Push down on the knob on top of motor housing to activate oscillation 2 Problem Can not adjust the angle of the fan Solution Loosen the adjustment knob tilt the fan then retighten adjustment knob TECHNICAL SUPPORT If you have any additional questions or problems with your Hunter Portable Fan please call USA 1 888 830 1326 Canada 1 866 268 1936 Hours of operation are from 7 00 am to 7 00 pm Monday Friday and 8 00 am to 5 00 pm on Saturday Central Time You may also contact us over the Internet at www hunterfan com WARRANTY The Hunter Fan Company makes the following limited warranty to the user or consumer pur
4. ESPECT TO THE GLASS GLOBES OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE FAN THIS WARRANTY 15 IN LIEU OF ALL OTHER EXPRESS WARRANTIES THE DURATION OF ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN RESPECT TO ANY HUNTER FAN MOTOR OR OTHER FAN PART IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH MOTORS AND OTHER PARTS This warranty is voided if your Hunter Fan is purchased and used in the USA This warranty excludes and does not cover defects malfunctions or failures of any Hunter Portable fan which were caused by repairs by persons not authorized by us use of parts or accessories not authorized by us mishandling improper installation modifications or damage to the Hunter Portable fan while in your possession or unreasonable use including failure to provide reasonable and necessary maintenance To obtain servicing contact the nearest Hunter authorized service center or the Hunter Fan Company Service Department 7130 Goodlett Farms Pkwy Suite 400 Memphis Tennessee 38016 Please contact us before shipping your fan to us If we authorize you to ship it to us you will be responsible for all insurance and freight or other transportation charges to our factory service center We will return your Hunter Fan freight prepaid Your portable fan should be properly packed to avoid damage in transit
5. English ing t 1 9 NN 4 TABLE OF CONTENTS 3 Safety and Warnings pp 3 Grounding 2 Fused aria neces 6 Ri 7 Base 7 Motor Assembly pp 8 Grill Assembly 9 OS 11 Off Speed Selection 11 Oscillation 11 Adjustment 11 12 NS 13 WO 13 POE E AEE 13 2010 Hunter Fan 2 44086 01 20101102 INTRODUCTION Thank you for choosing the Hunter Oscillating Stand Fan This manual gives you complete instructions for assembling and using your fan Here are some the features you will enjoy with your fan Y attractive design that enhances any decor powerful motor for maximum air flow V Three speeds to adjust your comfort level All metal construction SAFETY AND WARNINGS To reduce the risk of fire or electrical shock DO NOT use this fan with any solid state speed control device When using electrical appliances basic precautions should always be taken to reduce the risk of fire electric shock and personal injury Read all instructions before using this fan 1 Improper installation may result in the risk of fire electric shock or personal injury 2 To prevent the risk of fire and electric shock DO NOT use the unit near windows Rain and moisture may create an electrical hazard 3 The po
6. Oscillation To allow the fan to oscillate push the Knob beside the fan speed control down Pull up on the knob if oscillation is not desired Figure 20 Adjustment To adjust the angle the fan is blowing 1 Loosen the adjustment knob under the Fan Motor 2 Adjust the fan to the angle desired and retighten the knob to secure the fan at that angle Figure 21 When adjusting the height of the fan always grip the pole above the adjustment knob firmly to prevent the telescoping pole from collapsing 2010 Hunter Fan Co 11 44086 01 Figure 21 20101102 MAINTENANCE This fan is permanently lubricated and will not require additional lubrication oil for the life of the fan This fan requires little maintenance and contains no user serviceable parts DO NOT try to fix it yourself Contact qualified service personnel if servicing is needed Before cleaning turn fan off and unplug from electrical outlet Wipe off excess dust with a lintfree cloth To ensure adequate air circulation to the motor keep vents located at the rear of the motor housing free from dust accumulation A vacuum cleaner hose can be used to clean these vents DO NOT immerse the fan in water or any other liquid CLEANING THE GRILL AND BLADE 1 Turn the fan off and unplug from the electrical outlet 2 Disassemble the grills by Loosening the screw holding the grill ring and remove it from the grills 3 Two tabs hold the Front Grill and
7. chaser of this Hunter Portable fan If your Hunter Portable Fan motor fails at any time within five years after the date of sale to you due to a defect in material or workmanship labor to repair the defect will be provided free of charge at our nearest service center or our Service Department in Memphis Tennessee You will be responsible for labor costs after this one year period The foregoing limited warranty applies only to the motor itself and does not apply to electronic controls such as remote controls remote control receivers or transmitters used in conjunction with the motor These electronic control items are included in the one year limited warranty below If any part of your Hunter Portable Fan other than the motor fails at any time with five year after the date of 2010 Hunter Fan Co 13 44086 01 20101102 sale to you due to a defect in material or workmanship we will repair or at our option replace the defective part free of charge for parts and labor performed at our nearest service center or at our Service Department in Memphis Tennessee IF THE USER OR CONSUMER PURCHASER CEASES TO OWN THE FAN THIS WARRANTY AND ANY IMPLIED WARRANTY WHICH THEN REMAINS IN EFFECT INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE VOIDED NO WARRANTY EXPRESSED OR IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS MADE IN R
8. e 12 Note 1 screw will have a star washer on it for grounding purposes The other 3 screws will not have a washer ce Ke ECE 3 Loosen the Screw on the back of the Fan Blade 10 13a and slide the Fan Blade onto the post on the Motor 5 Figure 13 4 Tighten the Screw on Blade 10 to secure it to the Motor 5 Figure 14 Caution Ensure when tightening the screw on the back of the fan blade you tighten it on the flat part of the post Figure 14 2010 Hunter Fan Co 9 44086 01 20101102 GRILL ASSEMBLY CONT Remove the Grill Ring from the Front Grill 11 by loosening the screw holding it Place the Front Grill 11 against the Back Grill 9 so the Hunter logo faces right side up and push together until the tabs on the grills hold them together Figure 15 Slide the Grill Ring over both Front 11 and Back 9 Grills turning it so the screw that will secure it is on the bottom Figure 16 Tighten the Screw to secure the Grill Ring over the Front and Back Grills Straighten the Cord from the Motor along the Telescoping Pole and Snap the Cord Clip over the cord onto the Pole so the cord rests in the notch on the Clip Figure 18 2010 Hunter Fan Co 10 13 Cord Clip Notch 44086 01 Figure 18 20101102 OPERATION Off Speed Selection To turn the fan on and off control speed Turn the speed knob on the top of the motor to the porper setting Figure 19
9. g three blade grounding type plugs to two slot receptacles The adapter must be properly grounded DO NOT attempt to defeat the purpose of this safely feature 18 The rubber ring on this product may interact with wood and cause damage to furniture Do not place on fine wood furniture 2010 Hunter Fan Co 4 44086 01 20101102 GROUNDING This appliance is for household use only and may be plugged into any 120 volt AC electrical outlet ordinary household cur rent DO NOT use any other type of outlet Grounded WARNING Grounding Pi rounding Pin Grounded Outlet This unit is suitable for grounded receptacle use only Box Cover The power cord has a grounded plug as shown in Figure Figure 1 1 and must be used with an electrical outlet that can accommodate the grounding pin If your electrical outlet can not accommodate the grounding pin then you must purchase and install one of the two types of adapters shown in Figure NOTE The adapters ARE NOT supplied with this fan Read follow and save the instructions that are included Grounding Grounded Outlet with the adapter you choose Do not use an adapter if Box Cover your electrical outlet can accommodate the grounding pin LINE CORD SAFETY TIPS Figure 2 1 NEVER pull or yank on the cord or the appliance 2 To insert plug grasp it firmly and guide it into the outlet 3 To disconnect the appliance grasp the plug and remove it from t
10. he outlet 4 Before each use inspect the line cord for cuts and or abrasion marks If any are found the appliance should be serviced and the line cord replaced Please return it to our Service Department or to an authorized service representa tive 5 NEVER wrap the cord tightly around the appliance as this could place undue stress on the cord where it enters the ap pliance and could cause it to fray and break 6 DO NOT operate appliance if the line cord shows any dam age if the appliance works intermittently or stops working entirely 2010 Hunter Fan Co 5 44086 01 20101102 FUSED 6 This plug is a safety feature It contains a safety device fuse that should not be removed Discard product if the attachment plug is damaged To reduce the risk of fire electric shock and personal injury DO NOT remove replace repair or tamper with the originally supplied plug If the Fan does not function properly it may be due to the safety device incorporated in this plug If the fuse fails it is generally due to a short circuit or circuit overload Replace the fuse as per the instructions below If the replacement fuse fails immediately unplug the unit and contact our technical support department for assistance Fuse Replacement 1 replace the fuse first turn the unit it off and unplug it from the wall Locate the door on top of the plug Figure 1 2 Slide the door on top of the plug towards the blades Figure 2
11. since we will not be responsible for 2010 Hunter Fan Co 14 44086 01 20101102 such damage Proof of purchase is required when requesting warranty service The purchaser must present sales receipt or other document that establishes proof of purchase IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU THE WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Santer Company 7130 Goodlett Farms Pkwy Suite 400 Memphis Tennessee 38016 Printed in china and Taiwan 2010 Hunter Fan Co 15 PRODUCTS To learn more about Hunter Fan Company products please see our Web page at www hunterfan com 44086 01 20101102
12. wer plug must be removed from the power socket when not in use before cleaning servicing maintenance and before moving to another location 4 DONOT put fan in a damp place or where humidity is high such as a bathroom 5 The fan should be placed on a flat stable surface or tabletop to avoid overturning 6 Use fan only for intended use as described in this instruction manual 7 To protect against electrical shock DO NOT immerse unit plug or cord in water or spray with liquids 8 Close supervision is necessary when any appliance is used by or near children 9 NEVER insert fingers pencils or any other objects 2010 Hunter Fan Co 3 44086 01 20101102 through the grill when the fan is running 10 NOT operate any appliance with a damaged cord or plug after the appliance malfunctions or has been dropped or damaged in any manner 11 disconnect grip plug and pull from wall outlet NEVER yank on cord 12 ALWAYS use on a dry surface 13 This product is intended for household use only and not for commercial or industrial use 14 DO NOT operate fan in the presence of explosive and or flammable fumes 15 DO NOT place fan or any parts near an open flame cooking or any other heating appliances 16 DO NOT use near curtains plants window treatments etc 17 This appliance has a grounded three prong plug and is suitable for grounded receptacle use only An adapter is available for connectin
Download Pdf Manuals
Related Search