Hunter Fan 42751-01 Fan User Manual
Contents
1. odels Owner s Guide and Installation Manual For reference also attach your receipt or a copy of your receipt to the manual For Your Records and i a Warranty Assistance Ty eC D Vi yp FY LILY SINCE 1886 Form 42786 01 20090814 2009 Hunter Fan Co Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent 4 e Wiring2. With a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly A WARNING Use only the light fixture supplied with this fan model The switch housing assembly is made up of three sections the switch housing gasket the upper switch housing and the lower switch housing light assembly ATTACHING THE SWITCH HOUSING GASKET AND UPPER SWITCH HOUSING 7 1 Locate the switch housing mounting plate the switch housing gasket and the upper plug connector as shown NOTE Your fan may come with the switch housing gasket attached to the switch housing mounting plate If the switch housing gasket is attached to the switch housing mount ing plate go to the section Attaching the Upper Switch Housing If the switch housing gasket is not attached complete the steps below 7 2 Identify the top side of the switch housing gasket by looking for the raised circular ridge on the gasket 7 3 With the top side of the switch housing gasket facing up towards the motor align the holes in the gasket with the spokes on the switch housing mounting plate 7 4 Feed the upper plug connector through the center opening of the upper switch housing Push the gasket up so that it is seated flush with the mounting plate A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing and
3. the Fan warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade Table Of Contents 1 e Getting Ready 2 Installing the Ceiling Plate 3 e Assembling and Hanging the Fan 5 Installing the Canopy 6 Assembling the Blades 7 Completing Your Installation With a Bowl Light Fixture attachment system when installing balancing or cleaning the fan 8 e Operating and Cleaning Your Never insert foreign objects between rotating fan blades Cainer e To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed 9 Troubleshooting controls 2009 Hunter Fan Company 2 42786 01 08 14 09 e Hunter Fan Company Installer s Choice and Optional Accessories Support Brace Ceiling Standard Outlet Box Mounting gt Style Standard Mounting hangs from the ceiling by a downrod included Angled Mounting recommended for a vaulted or angled ceiling 42786 01 08 14 09 e Hunter Fan Company Understanding Mounting and Installers Choice Hunter s patented 2 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one o
4. 3 3 Loosen the square head set screw on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is I Ar Ee T S normal Securely retighten the set screw with a wrench or pliers A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod 3 4 Raise the fan and place the hook on the ceiling plate through the U shaped hole in the rim 6 42786 01 08 14 09 e Hunter Fan Company 4 Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 1999 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 Before attempting installation make sure the power is still off 4 2 To connect the wires hold the bare metal leads together and place a a wire connector over them then twist clockwise until tight For all these connections use the wire connectors provided Wire Connector Dual Switch Wiring 4 3 Connect the bare or green ground wire grounding from the ceiling to the green ground wire grounding from the ceiling plate and t
5. d damage to the product Align the keyhole slots in the lower switch housing with the housing assembly screws that were installed in Step 7 8 Turn the lower switch housing clockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots Tighten all housing assembly screws lI Step 7 7 42786 01 08 14 09 Hunter Fan Company 7 Completing Your Installation With a Bowl Light Fixture Continued Installing the Glass Bowl 7 13 7 14 7 16 7 17 7 18 7 19 7 20 Note In compliance with US federal energy regulations this ceiling fan contains a device that restricts the light kit to a maximum of First install B10 candelabra bulbs 60 Watt Maximum into the sockets Attach the extra pull chain included to the fan pull chain using the plastic breakaway connector You may find the plastic breakaway connector on the end of the extra chain Thread the fan pull chain coming from the side of the light kit down through the closest hole in the metal disc Then thread the fan chain through the bottom of the glass bowl and finally through the grommet hole in the cover plate Thread the light pull chain coming from the center of the light kit through the bottom of the glass bowl and the center of the cover plate Place the cover plate up against the glass bowl Align the holes in the cover plate and glass bowl Thread the lig
6. ed e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 In Canada call 1 866 268 1936 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 4 Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped 42786 01 08 14 09 e Hunter Fan Company 2 Installing the Ceiling Plate A CAUTION To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel 2 1 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter 2 2 Al
7. f two ways depending on ceiling height and your preference Standard or Angled mounting The steps in this manual include instructions for both Installer s Choice mounting methods Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance A CAUTION To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied 3 gt l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommend
8. he green ground wire from the fan 4 4 Connect the white wire grounded from the ceiling to the white wire grounded from the fan 4 5 Connect the remaining wires as follows Dual Switch Wiring e The black wire ungrounded from the ceiling to the black wire ungrounded from the fan e The black white wire ungrounded from the fan to the wire ungrounded for the wall switch Single Switch Wiring e The black wire ungrounded from the ceiling to the black ungrounded and the black white wire ungrounded from the fan A CAUTION Be sure no bare wire or wire strands are visible after making connections 4 6 Turn the splices upward and push them carefully back through the ceiling plate into the outlet box 4 7 Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box 7 42786 01 08 14 09 e Hunter Fan Company 5 1 5 2 5 4 5 5 5 6 5 Installing the Canopy Partially install two canopy screws into the ceiling plate and one time Holding the canopy raise the fan off the hook Align the slots in the canopy with the already partially installed canopy screws on the ceiling plate Raise the canopy over the ceiling plate Rotate the canopy clockwise until the canopy screws on the ceiling plate totally engage with the slots in the canopy Install the
9. ht pull chain through the center of the finial Screw the finial onto the threaded rod end until tight Attach the extra pull chain included to the light pull chain using the plastic breakaway connector You may find the plastic breakaway connector on the end of the extra chain 190 Watts Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation Fan Pull Chain Breakaway Connector Ll Light Bulbs B10 Candelabra Base 60 Watt Maximum Metal Disc Threaded Rod Light Pull Chain lt Glass Bowl Cover Plate Finial 12 42786 01 08 14 09 Hunter Fan Company 8 1 8 2 8 3 8 4 8 5 8 Operating and Cleaning Your Ceiling Fan Turn on electrical power to the fan The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector The light pull chain controls the power to the light fixture The chain has two settings ON and OFF For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface sm
10. ign the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other 2 3 Place the ceiling gasket over the ceiling plate so that the slots and the raised surfaces on the ceiling gasket align with the slots and holes on the ceiling plate 2 4 Use a 3 wood screw to pierce two holes in the ceiling gasket that match the pilot holes you drilled in step 2 1 2 5 Thread the lead wires from the outlet box down through the hole in the middle of the ceiling gasket and ceiling plate Note The ceiling gasket should be flush against the ceiling Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Wood Screw EEE tint 5 42786 01 08 14 09 Hunter Fan Company Steps 2 2 Steps 2 3 2 5 a _ For Angled Ceilings Be sure to orient the ceiling plate so that the arrows printed on the ceiling plate are pointing toward the ceiling peak 3 Assembling and Hanging the Fan A WARNING Fan may fall if not assembled as directed in these Steps 3 2 3 3 installation instructions 3 1 Unbundle the wires from the fan For Standard or Angle mounting 3 2 To assemble fan to hang down from a flat or angled ceiling insert the downrod through the canopy Feed the wires from the fan through the downrod
11. light fixture falling 10 42786 01 08 14 09 Hunter Fan Company 7 5 7 6 7 8 7 2 7 10 7 11 7 12 7 e Completing Your Installation With a Bowl Light Fixture Continued ATTACHING THE UPPER SWITCH HOUSING Locate the switch housing mounting screws in the sack parts Insert and tighten the screws into the outermost holes in the upper switch housing A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all four housing assembly screws could result in water entry into live connection area and or the switch housing and light fixture falling ATTACHING THE LOWER SWITCH HOUSING LIGHT ASSEMBLY Locate the housing screws NOTE Depending upon your fan model these screws may be installed in the four spokes from the switch housing mounting plate or they may be located in the sack parts Partially install the screws into the spokes from the switch housing mounting plate NOTE if these screws came installed make sure that they are partially installed in order to complete the following steps Connect the upper plug connector to the lower plug connector from the lower switch housing assembly NOTE Both plug connectors are polarized and will only fit together one way Make sure that both connectors are properly aligned before connecting them together Incorrect connection could cause improper operation an
12. n off at the wall switch Wait 30 seconds then resume power to the fan If you need parts or service assistance please call 888 830 1326 In Canada call 1 866 268 1936 or visit us at our Web site at http www hunterfan com Hunter Fan Company 7130 Goodlett Farms Pkwy 400 Memphis Tennessee 38016 14 42786 01 08 14 09 Hunter Fan Company
13. third canopy screw into the canopy Once all three screws are in tighten them Lift the fan housing toward the ceiling and rotate the fan until each canopy tab engages a groove in the hanger ball Note If the tabs are already engaged do not rotate Canopy Screw 8 Step 5 2 Ceiling Plate gt lt 3 Step 5 3 Steps 5 4 5 5 Ceiling Plate Hanger Ball 42786 01 08 14 09 Hunter Fan Company 6 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan 6 1 Your fan may include blade grommets If your fan has grommets Step 6 1 Detail insert them by hand into the holes on the blades 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 6 3 Remove the blade mounting screws and rubber shipping bumpers from the motor Note Some blade mounting screws are installed in the motor to secure shipping blocks 6 4 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade mounting screw then securely tighten both mounting screws Blade Assembly Use with grommet ews Use without grommet Blade Mounting Screw 42786 01 08 14 09 e Hunter Fan Company 7 Completing Your Installation
14. udges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish 13 42786 01 08 14 09 Hunter Fan Company 9 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Pull the pull chain to ensure it is on 5 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated Problem Lights dim when turned on or do not turn on 1 Check to make sure wattage of light bulbs installed match the specifications on the light socket Problem If the light on this fan shuts off suddenly 1 Turn the power to the fa
Download Pdf Manuals
Related Search