Hunter Fan 42660-01 Fan User Manual
Contents
1. 42660 01 01 30 08 Hunter Fan Company tting Ready To install a ceiling fan be sure you can do the following Locate the ceiling joist or other suitable support in ceiling Drill holes for and install wood screws Identify and connect electrical wires Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit Standard screwdriver magnetic tip recommended Phillips head screwdriver magnetic tip recommended Wrench or pliers Ladder height dependent upon installation site Installing Multiple Fans Checking Your Fan Parts If you are installing more than Carefully unpack your fan to avoid damage to the fan parts Refer to one fan keep the fan blades and the included Parts Guide Check for any shipping damage to the motor blade irons if applicable in sets or fan blades If any parts are missing or damaged contact your Hunter as they were shipped dealer or call Hunter Technical Support Department at 866 268 1936 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings2. 42660 01 01 30 08 Hunter Fan Company 2 Installin A CAUTION To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel 2 1 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter For Angled Ceilings Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak 2 2 Your fan comes with four preinstalled noise isolators Check to make sure all four isolators are in place and were not removed during shipment 2 3 Place a flat washer on each of the two 3 wood screws 2 4 Thread the supply wires from the outlet box in the ceiling through the hole in the center of the ceiling plate 2 5 Align the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be flush against the ceiling 2 6 Pass the screws through the slotted holes in the ceiling plate into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten lt _
3. A Breakaway Connector the plastic breakaway connector You may find the plastic breakaway connector on the end of the extra chain Thread the fan pull chain through the hole in the metal disk Then thread the fan pull chain through the hole in the center of the glass glass bowl Align the holes in the cover f Thread the light pull chain through the hole in the center of the hain throught the hole in rommet hole in the side of Light Bulbs B10 Candelabra Base 60 Watt Maximum L eee Metal Rod 7 Metal Disk Glass Bowl Cover Plate __ Finial 42660 01 01 30 08 Hunter Fan Company 8 Completing Your Installation V ure Continued 8 16 8 18 8 19 8 20 8 21 8 22 Uninstalling the Light Fixture between the black wire and the black white wire Disconnect the plug connectors between the two white wires Uninstall the connector and washer from the end of the light fixture inside the lower switch housing Unscrew the threaded rod of the light fixture from the lower switch housing Remove the light fixture from the lower switch housing pulling disconnected wires through the hole in the center of the lower switch housing Note When removing the wires pull the thin plug connector male through first and then pull the other plug connector female through the hole Install the dummy terminals included in the sack p
4. For Your Records and Warranty Assistance Model Name Catalog Model No Serial No Date Purchased Where Purchased For reference also attach your receipt or a copy of your receipt to the manual installation and operation manual for Hunter Ceiling Fans 42660 01 01 30 08 Table Of Contents 1 Getting Ready 0005 4 2 Installing the Ceiling Plate 3 Assembling and Hanging the Fan 6 4 Securing Fan to Secondary Support SYSUEN PEPPE TENE ENA EET 7 5 Wiring the Fan 0605 8 6 Installing the Canopy and Canopy S sh s iesicasiesnieneee swehien 9 7 Assembling the Blades 10 8 Completing Your Installation With or Without a Bowl Light Fixture 11 9 Operating and Cleaning Your Ceiling FAM ses cenedicneeined nacnasionnnies 15 2008 Hunter Fan Company elc e Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnin
5. Hunter Fan Company mpleting Your Installation 8 6 To attach the lower switch housing connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product Place the lower switch housing assembly over the upper switch housing Align the side screw holes in the upper and lower switch housings Attach the lower switch housing to the upper switch housing with three housing assembly screws Plug Connector Pi Steps 8 6 8 7 Lower Switch Housing Plug Connector Detail __ Housing Assembly Screw 42660 01 01 30 08 Hunter Fan Company mpleting Your Installation V 8 9 8 10 8 12 8 13 8 14 Installing the Glass Bowl sockets 8 8 First install B10 candelabra bulbs 60 Watt Maximum into the Attach the extra pull chain included to the fan pull chain using bowl glass bowl Then Thread the light pull cl the center of the cover plate Thread the fan pull chain through the gi the cover plate Place the cover plate up against the plate and glass bowl Thread the light pull chain through the finial and screw the finial onto the threaded rod end until tight
6. depending on ceiling height and your preference Low 1 Ceiling t Profile Standard or Angled mounting The steps in this manual include Standard Outlet Box instructions for all three Installer s Choice mounting methods Mounting Style Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum Standard Mounting hangs from the performance of your Hunter fan use only Hunter speed controls ceiling by a downrod included For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance Support Brace Ceiling Outlet Box 8 Support Brace A CAUTION To reduce the risk of 12 personal injury attach aT 2 Angled Q y the fan directly to the Mounting 1 Style Low Profile _ Ceiling support structure of Mounting Outlet Box the building accordin Style 5 E to these instructions and use only the hardware supplied Angled Mounting recommended for a Low Profile Mounting fits close to the vaulted or angled ceiling ceiling recommended for ceilings less than 8 feet high
7. vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish In warm weather use downward air flow pattern In cold weather use upward air flow pattern To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position Restart fan Reversing 42660 01 01 30 08 Hunter Fan Company 10 ubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 If your fan wobbles when
8. Flat Washer 3 Wood Screw CT t he Ceiling Plate Toward Ceiling Peak gt For Angled Ceilings Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak Steps 2 3 2 6 42660 01 01 30 08 Hunter Fan Company A WARNING Fan may fall if not assembled as directed in these installation instructions 3 1 Unbundle the wires from the fan For Standard or Angled mounting 3 2 Insert the downrod through the canopy and canopy trim ring Feed the wires from the fan through the downrod on one side of the pin in the ball 3 3 Loosen the square head set screw on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the set screw with a wrench or pliers Skip to step 3 7 A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod For Low Profile mounting Note For low profile mounting the downrod is replaced with the low profile washer 3 4 Remove the set screw from the adapter 3 5 Place the low profile washer into the canopy with the lip down 3 6 Align the holes in the washer with the holes in the adapter Assemble securely with three low profile screws H
9. anging the Fan Note To hang the fan you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks 3 7 Raise the fan and align the slots in the canopy with the hooks on the ceiling plate 3 8 Place the slots over the hooks to hang the fan Standard or Angled Mounting Steps 3 2 3 3 lt _ Downrod lt Canopy I lt Canopy Trim Ring Low Profile Mounting Steps 3 5 3 6 Low Profile Screws Low Profile Green A Ground Wire Canopy Trim Ring Step 3 6 Detail Adapter Low Profile Screw Low Profile Washer 42660 01 01 30 08 Hunter Fan Company 4 3 4 4 4 5 4 6 4 7 4 8 2 Access the support brace in the ceiling You may not be able to do 4 Securing Fan to Second Find the looped end of the braided cable and insert it through the ceiling plate and one of the holes in the outlet box into the ceiling this from below the ceiling depending on your installation site Drive a wood screw and washer into the side of the brace that holds the outlet box Leave 3mm 1 8 of space between the support brace and the washer Wrap the braided cable around the support brace once creating a complete circle Hook the looped end of the cable over the wood screw so that the braided cable lies between the washer and the support brace Tighten the loop and secur
10. arts on the two disconnected wires in the lower switch housing Install the switch housing cap and plug button to the lower switch housing Once you have uninstalled the light fixture continue with step 8 6 Male Dummy Terminal ae Terminal 8 15 To uninstall the light fixture first disconnect the plug connectors Lower Switch lt 4 Housing lt Threaded Rod Steps 8 17 8 19 Cap oe Plug Button ____ l ad Step8 21 42660 01 01 30 08 Hunter Fan Company 9 3 9 4 9 5 Operating and Clea Turn on electrical power to the fan The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off Pull the chain slowly to change settings Release slowly to prevent the chain from recoiling into the blades The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A
11. e the screw and washer all the way down to the support brace Coil up the excess cable Return to the fan so you can complete the fan wiring Steps 4 2 4 3 imme Support Ceiling Steps 4 4 4 5 Brace Outlet Box Braided Cable 42660 01 01 30 08 Hunter Fan Company 5e ng the Fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 1999 If you are unfamiliar with wiring Sa Wire use a qualified electrician Connector Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 5 1 Before attempting installation make sure the power is still off Ke Single Switch Wiring O 5 2 To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight For all these connections use the wire connectors provided 5 3 Connect the bare or green ground wire grounded from the ceiling to the green ground wire grounded from the ceiling plate and the green ground wire from the fan 5 4 Connect the white wire ungrounded from the ceiling to the white wire ungrounded from the fan 5 5 Connect the remaining wires as follows Single Switch Wiring The black wire ungrounded from the ceiling to the black ungrounded and the black white wire
12. gs READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS Use only Hunter replacement parts To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls 42660 01 01 30 08 Hunter Fan Company Installer s Choice and Optional Accessories Support Brace Understanding Mounting and Installer s Choice 1 Hunter s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one T of three ways
13. operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated If you need parts or service assistance please call 866 268 1936 or visit us at our Web site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 42660 01 01 30 08 Hunter Fan Company
14. opy trim ring up to the top of the canopy The canopy trim ring will snap and lock into place Note Should you need to remove the trim ring press firmly on opposite sides of the trim ring directly above the groove in the hanger ball The tabs will flex out releasing the canopy trim ring Canopy Screw 42660 01 01 30 08 Hunter Fan Company embling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan 7 1 Your fan may include blade grommets If your fan has grommets Step 7 1 Detail insert them by hand into the holes on the blades 7 2 Attach each blade to a blade iron using three blade assembly l screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 7 3 Remove the blade mounting screws and rubber shipping bumpers from the motor Note Some blade mounting screws are installed in the motor to secure shipping blocks 7 4 For each blade insert one blade mounting screw through the boi Li blade iron and attach lightly to the fan Insert the second blade mounting screw then securely tighten both mounting screws Blade Assembly Screws Steps 7 1 7 2 Use with grommet T Use without grommet Blade Mounting 7 Screw 7 42660 01 01 30 08 Hunter Fan Company 8 Completing Y
15. our Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button This feature gives you the option of installing the fan with OR without the included light fixture The steps below direct you whether or not you are installing a light fixture A WARNING Use only the light fixture supplied with this fan model 8 1 To attach the upper switch housing partially install two housing assembly screws into the switch housing mounting plate 8 2 Feed the upper plug connector through the center opening of the housing 8 3 Align the keyhole slots in the housing with the housing assembly screws Housing 8 4 Turn the housing counterclockwise until the housing assembly Assembly Upper n F Switch screws are firmly situated in the narrow end of the keyhole slots Housing Install the remaining screw into the housing Tighten all three screws firmly A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing and light fixture falling 8 5 If you want to install the light fixture proceed with step 7 6 now If you do not want to install the light fixture you need to uninstall it now See Uninstalling the Light Fixture on step 7 15 Once you have uninstalled the light fixture continue with step 7 6 42660 01 01 30 08
16. ungrounded from the fan A CAUTION Be sure no bare wire or wire strands are visible after making connections 5 6 Turn the splices upward and push them carefully back through the ceiling plate into the outlet box 5 7 Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box 42660 01 01 30 08 Hunter Fan Company 6 Installing the A WARNING Failure to complete the following steps could cause the fan to fall Note It is recommended you use a magnetic tip screwdriver for the following steps 6 1 Rotate the hanger ball so the tab in the canopy is secure in the hanger ball groove Note Your fan may have multiple tabs and grooves that must be aligned 6 2 Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate A WARNING The slots in the canopy must remain engaged while swinging the canopy for alignment 6 3 Holding the canopy up with the screw holes aligned partially install two canopy screws into the holes opposite the ceiling plate tabs 6 4 Partially install a canopy screw between the slots in the canopy When all the holes are properly aligned securely tighten all three canopy screws 6 5 Verify that the tabs in the canopy are still in the grooves of the hanger ball 6 6 Align the tabs on the trim ring opposite the grooves in the hanger ball Using both hands push the can
Download Pdf Manuals
Related Search