Huffy 104/03P/N211956B Fitness Equipment User Manual
Contents
1. REQUIRED TOOLS AND MATERIALS Two People Tape Measure Wood Board Scrap Wrenches Two 7 16 1 2 9 16 3 4 or Large and Small Adjustable Wrenches Sawhorse or Support Table Step Ladder 8 ft 2 4 m Garden Hose or Sand 225 Ib 102 kg Hammer Tape Phillips Screwdriver Safety Goggles ALL Huffy Sports basketball Systems including those used for DISPLAYS MUST be assembled and ballasted with sand or water according to instructions Failure to follow instructions could result in SERIOUS INJURY It is NOT acceptable to devise a makeshift weight System TO ADJUST BACKBOARD While holding handle remove pin Move elevator up or down to desired height Replace pin full length to lock system at desired height Adjust basketball backboard height to lowest position While holding pole rotate basketball system forward until wheels engage with ground Move basketball system to desired location Carefully rotate basketball system upright Reattach ground restraint and check system for stability 201252 2 99 A WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Owner must ensure that all players know and follow these rules for safe operation of the system DO NOT HANG on the rim or any part of the system including backboard support braces or net During play especially when performing dunk type2. slides over the top of the first arm as shown Push in direction indicated by arrows Push second arm back and into ram as shown Twist body of clip slightly again to spread arms of clip Clip arms must be flat and touching edge to edge as shown not overlapping P N 211956B 04 03 12 NET INSTALLATION 2 Insert net into bottom of clip as shown loi ST eee Twist net until it snaps into position Net must be centered through clip 13 SIDE VIEW SIDE VIEW 04 03 P N 211956B
3. bolt 47 through left side upper elevator tube 43 then stretch spring 41 onto bolt 47 Insert bolt 47 through right side upper elevator tube 43 and secure with nut 39 WARNING USE EYE PROTECTION WHEN INSTALLING SPRINGS Roll completed assembly to desired playing area Fill tank with water approx 30 gallons 113 Liters or sand approx 255 16 113 kg and snap cap 49 in place Secure assembly to ground using anchor strap 52 and tie down stake 53 IMPORTANT Add two gallons 7 6 Liters of non toxic antifreeze in sub freezing climates WARNING DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY MAY TIP OVER While holding handle remove pin 26 WARNING DO NOT ALLOW CHILDREN TO ADJUST HEIGHT Move elevator up or down to desired height Replace pin 26 full length to lock system at desired height Apply height and transport label 54 to front of pole as shown Regulation rim height is 10 feet 3 05m Install front cover 57 onto struts 11 as shown Loop zip tie 56 around strut 11 and cover 57 Pull flat end of zip tie 56 through square end of zip tie until completely tightened NOTE Ridges on zip tie 56 should be on inside of loop when pulling flat end of tie through square end Once fully secured in the four areas shown trim excess of zip tie 56 with scissors A WARNING USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS OR WHEN ALL SMART CLIPS ARE NO
4. to ream out any possible excess paint ENGLISH INSTRUCTIONS IMPORTANT WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF 16 Install spacers 36 onto backboard brackets 34 with bolts 37 21 and lock nuts 35 20 as shown THIS OWNERS MANUAL 17 Assemble lower elevator tubes 40 as shown Remove all contents from underside of tank Keep tank 1 bottom side up Insert axle rod 2 through wheel 3 as shown Secure wheel assembly to tank 1 by tapping wheel downward with hammer snapping it into position Repeat for opposite side then carefully turn tank 1 over Mark pole sections with tape as shown IMPORTANT Center alignment slot of middle pole section 5 ina lower hole of top pole section 4 as shown While maintaining alignment bounce pole top 4 and middle section 5 together as shown until they no longer move toward taped reference mark Upright assembly NOTE Pole sections should have a 3 1 2 9 cm minimum overlap IMPORTANT Center alignment slot of lower pole section 6 in a lower hole of middle pole section 5 as in step 4 While maintaining alignment bounce assembly and lower section 6 together as shown until they no longer move toward taped reference mark NOTE Pole sections should have a 3 1 2 9 cm minimum overlap Install rod 7 through holes in bottom pole section 6 and eyebolt 8 Insert pole assembly into tank assembly as shown Carefully place unit on its side Secure pole bottom 6 to t
5. 04850 Pin Locking 27 1 204853 Lanyard Black 28 1 904833 Height Adjustment Rod 29 1 204872 Label Height Indicator 30 2 203103 Carriage Bolt 5 16 18 x 2 Long 31 1 204803 Screw Phillips Head 32 1 204855 Handle Left 33 1 204856 Handle Right 34 2 900846 Board Bracket 35 1 203493 Nut 1 4 20 Center Lock 36 2 201129 Spacer 402 I D x 5 x 1 8 Long 37 1 240017 Bolt Hex Head 1 4 20 x 2 1 4 Long 38 6 206311 Spacer Plastic 530 1 0 x 50 Long 39 7 206340 Locknut Hex Head 1 2 13 40 2 904820 Elevator Tube Lower Long 41 1 204838 Spring 42 1 Rim 43 2 904808 Elevator Tube Upper Short 44 4 201651 Spacer 1 4 Long x 1 2 O D 45 2 900867 Plate Triangle Black 46 1 202814 Cap Pole Top 47 6 206244 Bolt Hex 1 2 13 x 8 Long 48 1 204870 Bolt Hex 1 2 13 x 3 1 2 Long 49 2 203617 Plug Cap 50 12 201219 Smart Clip Net Holder 51 1 Net 52 1 201568 Anchor T Strap 53 1 203124 Stake Tie Down 54 1 201252 Label Height Adjustment and Moving 55 6 202862 Spacer 563 I D x 1 19 Long 56 4 203257 Zip Tie 57 1 203255 Front Cover WARRANTY CARD Please remember to complete your product You may have extra parts with this model registration form either on line at www huffysports com warrantycard or mail in the enclosed postcard P N 211956B 04 03 4 BEFORE YOU START Test fit bolts into large holes of elevator tubes backboard brackets and triangle plates Rock the bolt in a circular motion
6. HUFFY SPORIS A Huffy Company WRITE IN YOUR MODEL NUMBER J Portable Basketball System with Elevator Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex WI 53089 U S A M O R TA N T In U S and Canada only Have guestions don t go back to the storel We appreciate your purchasing one of our many fine products We are sure that you will be very satisfied with your selection Although great care and effort have been taken occasionally problems may occur To ensure prompt and correct handling of any problems or to answer any questions please contact our Toll Free Customer Service Number listed below Service will be quicker if you have your Model Numb found on carton and assembly instructions ready when calling PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE SLYOdS Aq 2002 LHOISHAdOO A SAFETY INSTRUCTIONS NOTICE TO ASSEMBLERS 0 70 FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the system To ensure safety do not attempt to assemble this system without following the instructions carefully Proper and complete assembly use and supervision is essential for proper operation and to reduce the risk of accident or injury A high probability of s
7. T PRESENT COULD RESULT IN BODILY HARM BE SURE TO FOLLOW DIRECTIONS CAREFULLY Install net clips as shown See illustration Install net as shown See illustration 04 03 P N 211956B IMPORTANT WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL E 13 cm BOTTOM TP See Text Page IMPORTANT See Text Page WOOD SCRAP P N 211956B 04 03 6 IMPORTANT See Text Page AWARNING See Text Page P N 211956B PORTANT See Text Page IMPORTANT See Text Page P N 211956B 04 03 IMPORTANT See Text Page Note See Text Page IMPORTANT For spring loaded rim assembly refer to instructions included with rim hardware See Text Page See Text Page 9 04 03 P N 211956B Note See Text Page AWARNING See Text Page AWARNING IMPORTANT See Text Page P N 211956B 04 03 3 05 m AWARNING See Text Page P N 211956B e Install net clips A Use of this product without proper installation of net clips or when all net clips are not present could result in bodily harm Be sure to follow directions carefully inam CLIP ARM Pt P BE CLIP BODY Insert one arm of clip into ram as shown Twist body of clip slightly so that second arm
8. activities keep player s face away from the backboard rim and net Serious injury could occur if teeth face come in contact with backboard rim or net Do not slide climb shake or play on base and or pole After assembly is complete fill system completely with water or sand and stake to the ground Never leave system in an upright position without filling base with weight as system may tip over causing injuries When adjusting height or moving system keep hands and fingers away from moving parts Do not allow children to move or adjust system During play do not wear jewelry rings watches necklaces etc Objects may entangle in net Surface beneath the base must be smooth and free of gravel or other sharp objects Punctures cause leakage and could cause system to tip over Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with exterior enamel paint If rust has penetrated through the steel anywhere replace pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs corrosion and repair before use Check system before each use for instability Do not use system during windy and or severe weather conditions system may tip over Place system in the storage position and or in an area protected from the wind and free from personal property and or
9. ank with anchor strap 52 washers 9 amp 13 and nut 10 as shown Upright unit NOTE Keep unnecessary pressure off of the pole assembly when in this position Two people recommended for this procedure IMPORTANT Do not over tighten will crack tank Secure strut tubes 11 to bottom pole section 6 as shown WARNING TIGHTEN BOLT 14 IN LOCKNUT 12 UNTIL FLUSH EVEN WITH LOCKNUT S OUTER EDGE Once again carefully place unit in the side position and secure strut 11 to tank 1 as shown Completely tighten Repeat for opposite side Upright unit NOTE Keep unnecessary pressure off of the pole assembly when in this position Two people recommended for this procedure Install pole mount 17 bracket with carriage bolts 18 as shown Tighten flange nuts 16 completely Attach spacers 22 23 to pole mount bracket 17 with bolts 21 washers 19 and nuts 20 as shown IMPORTANT Tighten until washers 19 no longer move Attach covers 24 onto pole mount bracket 17 with carriage bolt 25 and nut 16 as shown IMPORTANT Loop end of pin lanyard 27 over carriage bolt 25 during this assembly NOTE Assemble lanyard 27 to locking pin 26 as shown Apply logo and height indicator labels 29 to adjustment rod 28 as shown Attach handle parts 32 33 to adjustment rod with screw 31 carriage bolt 30 and flange nut 16 as shown IMPORTANT Indicator labels should be applied as close to holes a
10. em 13 7 Item 9 1 Item 414 1 d LLL Item 15 2 Item 16 11 Item 18 2 6 1 gt om Item 19 4 Item 20 3 HARDWARE IDENTIFIER CONTINUED P N 211956B 04 03 2 HARDWARE IDENTIFIER CONTINUED Ld O Item 23 2 Item 25 3 Rn Item 30 2 Item 31 1 Item 35 1 T O Item 37 1 Item 47 6 Item 38 6 PF Item 55 6 3 04 03 PARTS LIST See Hardware Identifier Item Qty Part No Description 1 1 206336 Tank Gray 2 2 206330 Wheel Axle 4 1 4 Long 3 2 226401 Wheel 4 Black 4 1 904847 Top Pole Section 5 1 908481 Middle Pole Section 6 1 908487 Bottom Pole Section 7 1 202820 Rod 3 8 O D x 4 3 4 Long 8 1 202822 Eyebolt 3 8 16 x 3 3 4 Long 9 1 202821 Disk 2 3 4 Diameter 10 1 203063 Nylon Insert Lock Nut 3 8 16 11 2 906410 Strut 1 O D x 43 Long 12 1 203220 Nut Nylock 5 16 18 13 7 203218 Washer 5 16 Flat 14 1 202541 Bolt Hex Head 5 16 18 x 3 3 4 Long 15 2 203798 Bolt Hex Flange 5 16 18 x 1 1 2 Long 16 11 203100 Flange Nut 5 16 18 17 1 204832 Bracket Pole Mount 18 2 203231 Carriage Bolt 5 16 18 x 3 1 2 Long 19 4 220154 Washer metal 3 4 O D 20 3 201124 Locknut Hex Head 3 8 16 21 3 206360 Bolt Hex Head 3 8 16 x 2 5 8 Long 22 2 204858 Spacer Biscut plastic 23 2 204857 Spacer metal 1 2 O D x1 44 Long 24 2 204859 Cover Spring 25 3 203038 Carriage Bolt 5 16 18 x 2 3 4 Long 26 1 2
11. erious injury exists if this system is not installed mai ed and operated properly Check entire box and inside all packing material for parts and or additional instructional material Before beginning assembly read instructions and identify parts using hardware identifier and parts list in this document If using a ladder during assembly use extreme caution Two 2 people are recommended for this operation Check base regularly for leakage Slow leaks could cause system to tip over unexpectedly Seat the pole sections properly if applicable Failure to do so could allow the pole sections to separate during play and or transport of the system Climate corrosion or misuse could result in system failure If technical assistance is required contact Huffy Sports Minimum operational height is 6 6 1 98 m to the bottom of backboard This equipment is intended for home recreational use only and NOT excessive competitive play Read and understand the warning label affixed to pole Label is shown on Page 1 The life of your basketball pole depends on many conditions The climate placement of the pole the location of the pole exposure to corrosives such as pesticides herbicides or salts are all important Adult supervision is recommended when adjusting height For more information on assembly placement proper use and maintenance visit The American Basketball Council website at http www smarthoops com
12. overhead wires Never play on damaged equipment See instruction manual for proper installation and maintenance When moving system use caution to keep mechanism from shifting Keep pole top covered with cap at all times Do not allow water in tank to freeze During sub freezing weather add non toxic antifreeze sand or empty tank completely and store Do not use salt Use extreme caution if placing system on sloped surface System may tip over more easily HUFFY SPORTS In the U S 1 800 558 5234 and Canada 1 800 284 8339 The NBA and individual NBA member team identifications reproduced on this product are trademarks and copyrighted designs and or other forms of intellectual property that are the exclusive property of NBA Properties Inc and the respective NBA member teams and may not be used in whole or in part without the written consent of NBA Properties Inc CALME LU TUFF STUFF and associated trademarks are owned and used with permission of Mattel Inc Huffy products are not sponsored endorsed or authorized in any way by Mattel Inc or any of its affiliated or subsidiary companies Toll Free Customer Service Number for U S 1 800 558 5234 For Canada 1 800 284 8339 For Europe 00 800 555 85234 Sweden 009 555 85234 For Australia 1 800 333 061 Internet Address http www huffysports com 999611 N d HARDWARE IDENTIFIER OW Item 2 2 Item 10 1 Item 12 1 8 1 It
13. s possible to prevent labels from being damaged during height adjustment NOTE Holes in adjustment rod allow for either rear access or side access Insert handle assembly through pole mount assembly as shown Lock pole assembly in place at the 10 3 05 m mark with pin 26 IMPORTANT It is necessary for all parts to be installed for this mechanism to work safely and properly NOTE Test fit bolts into holes of brackets 34 and carefully rock them in a circular motion to ream out paint from holes if necessary Starting with nuts 16 flush against bracket 34 secure rim 42 and bracket to backboard IMPORTANT For spring loaded rim assembly refer to instructions included with rim hardware NOTE A Do not use washers here on spring return style rim NOTE B Mounting nuts and bolts supplied with rim hardware Bend bracket 34 to line up with holes in backboard and secure Assemble upper elevator tubes 43 to backboard brackets 34 Support pole on sawhorse Attach backboard assembly to top pole section 4 as shown Then install pole cap 46 NOTE Two people are recommended for this step Use caution elevator assembly is heavy Install upper elevator tubes 43 to triangle plates 45 as shown Install handle assembly to lower elevator tubes 40 using bolt 47 spacers 38 55 and nut 39 as shown NOTE Before going on to next step set adjustable system assembly to the 10 3 05 m setting Insert
Download Pdf Manuals
Related Search