Hotpoint 162D6746P002 Refrigerator User Manual
Contents
1. Safety Instructions ADJUST 5 0 IS OFF 6 ADJUST FREEZER 51S NORMAL REFRIGERATOR Operating Instructions Initially set the refrigerator control at 5 and the freezer control at 5 and allow 12 24 hours for the temperature to stabilize Several adjustments may be required Adjust the controls one mee increment at a time and allow 12 hours after each adjustment for the refrigerator to reach the temperature you have set Setting the controls to 0 stops cooling in both the refrigerator and freezer compartments but does not shut off electrical power to the refrigerator On some models only the refrigerator control has a 0 setting Touch pad controls A S S i B S cS g e Setting either control at 0 will automatically set the other control at 0 The zeros will blink until you set the controls a e f both controls are set at 0 and either COLDER pad is pressed the controls will automatically reset to 5 D r i S Control settings will vary based on personal preferences usage and 3 operating conditions and may require more than one adjustment E 2 3 Locking the Controls on some models This feature allows you to lock the controls so the settings cannot be changed To lock the controls To unlock the controls 7 Set the controls to the desired settings Press and hold the lock pad for 3 seconds Press and hold the lock pad for After unlocking the controls the sett2. Cleaning the Outside The door handles and trim Clean with a cloth dampened with soapy water Dry with a soft cloth Keep the outside clean Wipe with a clean cloth lightly dampened with mild liquid dish detergent Dry with a clean soft cloth Cleaning the Inside To help prevent odors leave an open box of baking soda in the refrigerator and freezer compartments Unplug the refrigerator before cleaning If this is not practical wring excess moisture out of sponge or cloth when cleaning around switches lights or controls Use warm water and baking soda solution about a tablespoon 15 ml of baking soda to a quart 1 liter of water This both cleans and Behind the Refrigerator Be careful when moving the refrigerator away from the wall All types of floor coverings can be damaged particularly cushioned coverings and those with embossed surfaces Pull the refrigerator straight out and return it to position by pushing it straight in Moving the Preparing for Vacation For long vacations or absences remove food and unplug the refrigerator Move the freezer control to the 0 off position and clean the interior with a baking soda solution of one tablespoon 15 ml of baking soda to one quart 1 liter of water Leave the doors open Preparing to Move Secure all loose items such as base grille shelves and drawers by taping them securely in place to prevent damage www Hotpoint com Do not wipe the refriger
3. e See Care and cleaning Moisture collects inside in humid weather air carries moisture into refrigerator when doors are opened Interior light does not work Hot air from bottom of refrigerator Food freezing in the refrigerator Door does not close by itself Orange glow in the freezer Too frequent or too long door openings No power at outlet e Replace fuse or reset the breaker Light bulb burned out Normal air flow cooling motor In the refrigeration process it is normal that heat be expelled in the area under the refrigerator Some floor coverings are sensitive and will discolor at these normal and safe temperatures Food too close to air vent e See Replacing the light bulbs e Move the food away from the air vent near the controls Refrigerator control is set too cold Rollers need adjusting Defrost heater is on e Move the refrigerator control to a warmer temperature e See Rollers e This is normal 23 suoyanysuy ajes suononysuy Guyesadg 2 2 Q 3 A S 3 a sdij Gurooysajqnosy pioddns sauinsuoy e Refrigerator Warranty For customers in the United States S All warranty service provided by our Factory Service Center or an Staple your receipt here authorized Customer Care technician To schedule service on line Proof of the original purchase 24 hours a day visit us at www Hotpoint com or call 800 G
4. Instructions INSTALLING THE WATER LINE oN some mobDELs BEFORE YOU BEGIN Recommended copper water supply kits are WX8X2 WX8X3 or WX8X4 depending on the amount of tubing you need Approved plastic water supply lines are refrigerator tubing kits WX08X10002 WX08X10006 WX08X10015 and WX08X10025 When connecting your refrigerator to a reverse osmosis water system follow the manufacturer s recommendations This water line installation is not warranted by the refrigerator or icemaker manufacturer Follow these instructions carefully to minimize the risk of expensive water damage Water hammer water banging in the pipes in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator To prevent burns and product damage do not hook up the water line to the hot water line If you use your refrigerator before connecting the water line make sure the icemaker power switch is in the 0 off position Do not install the icemaker tubing in areas where temperatures fall below freezing When using any electrical device such as a power drill during installation be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock or is battery powered All installations must be in accordance with local plumbing code requirements 12 WHAT YOU WILL N
5. It will lock in place Freezer Tilt Out Bin on some models Push the button as you tilt out the bin To remove Hold the sides of the bin and lift it straight up then pull out To replace Engage the ends of the bin in the molded supports on the door and push down It will lock in place NOTE Do not overload the bin To replace Place the rear shelf tabs just in front of the central notches on the shelf frame Slide the shelf in until the central tabs are slightly behind the front bar Lower the shelf into place until it is horizontal and slide the shelf in Make sure that the shelf sits flat after reinstallation and doesn t move freely from side to side Make sure you push the shelves all the way in before you close the door The snugger helps prevent tipping spilling or sliding of small items stored on the door shelf Grip the finger hold near the rear of the snugger and move it to fit your needs About the additional features Not all features are on all models Shelf Saver Rack on some models Slide out beverage rack holds 12 cans of soda or 2 wine water bottles lengthwise It can be removed for cleaning About the crispers and pans Not all features are on all models Fruit and Vegetable Crisper Excess water that may accumulate in the bottom of the drawers or under the drawers should be wiped dry www Hotpoint com To remov
6. DS E The flow of refrigerant through the freezer cooling coils may make a gurgling noise like boiling water E Water dropping on the defrost heater can cause a sizzling popping or buzzing sound during the defrost cycle E A water dripping noise may occur during the defrost cycle as ice melts from the evaporator and flows into the drain pan E Closing the door may cause a gurgling sound due to pressure equalization For additional information on normal icemaker operating sounds see the About the automatic icemaker section D 21 suoyanysuy ajes suonanysuy Guyesadg A 2 Q 3 A S S a sdij Gurooysajqnosy pioddns sauinsuoy 2 S T Q E S Problem Refrigerator does not operate Vibration or rattling slight vibration is normal Motor operates for long periods or cycles on and off frequently Modern refrigerators with more storage space and a larger freezer require more operating time They start and stop often to maintain even temperatures Refrigerator or freezer compartment too warm A S S S i B D S X a A S S i B S amp g n Q Frost or ice crystals gt d on frozen food S frost within package is normal Q Automatic icemaker a on some models does not work S 5 Frequent buzzing sound Consumer Support 22 Before you call for service Troubleshooting Tips Save time and mone
7. E CARES date is needed to obtain service gt 800 432 2737 under the warranty A For The Period Of We Will Replace One Year Any part of the refrigerator which fails due to a defect in materials or workmanship From the date of the During this full one year warranty we will also provide free of charge all labor original purchase and in home service to replace the defective part Five Years Any part of the sealed refrigerating system the compressor condenser evaporator From the date of the and all connecting tubing which fails due to a defect in materials or workmanship original purchase During this additional four year limited warranty we will also provide free of charge all labor and in home service to replace the defective part What Is Not Covered Service trips to your home to teach you how to use Damage caused after delivery ihe products Replacement of the light bulbs Operating Instructions Peiprope meialaion detya or maintenance Damage to the product caused by accident fire floods or Failure of the product if it is abused misused or used acts of God for other than the intended purpose or used commercially Incidental or consequential damage caused by possible defects with this appliance Loss of food due to spoilage Replacement of house fuses or resetting of circuit breakers This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use wit
8. EED e Copper or approved plastic refrigerator tubing kit 1 4 outer diameter to connect the refrigerator to the water supply If using copper be sure both ends of the tubing are cut square To determine how much tubing you need measure the distance from the water valve on the back of the refrigerator to the water supply pipe Then add 8 2 4 m Be sure there is sufficient extra tubing about 8 2 4 m coiled into 3 turns of about 10 25 cm diameter to allow the refrigerator to move out from the wall after installation Approved plastic refrigerator tubing kits are available in the following lengths 2 0 6 m WxX08X10002 6 1 8 m WX08X10006 15 4 6 m WxX08X10015 25 7 6 m WX08X10025 Be sure that the kit you select allows at least 8 2 4 m as described above NOTE The only approved plastic tubing is that supplied in the refrigerator tubing kits listed above Do not use any other plastic water supply line because the line is under pressure at all times Certain types of plastic will crack or rupture with age and cause water damage to your home Installation Instructions WHAT YOU WILL NEED CONT e A water supply kit containing tubing shutoff valve and fittings listed below is available at extra cost from your dealer or from Parts and Accessories 800 626 2002 A cold water supply The water pressure must be between 20 and 120 p s i 1 4 8 1 bar e Power dri
9. Lop Freezer igerators Refr www Hotpoint com Safety Instructions Adapter Plugs 0000 3 Connect Electricity 3 Extension Cords is Mdauaaeees 2 Proper Disposal 2 Safety Precautions 2 Operating Instructions Additional Features 7 Automatic Icemaker 8 Controls oerien a a 4 Crispers and Pans 7 8 Shelves and Bins 5 6 Care and Cleaning Care and Cleaning 9 Replacing the Light Bulbs 10 Installation Instructions Preparing to Install the Refrigerator 11 Reversing the Door Swing 16 20 Water Line Installation 12 16 Troubleshooting Tips 21 23 Normal Operating Sounds 21 Consumer Support Consumer Support Back Cover Warranty oh ee i So na lt call 2 24 Write the model and serial numbers here Model Serial Find these numbers on the gray label on the left side near the top of the refrigerator compartment Owners Manual amp Installation Instructions Models 22 25 200D2461P004 39 60351 09 04 JR IMPORTANT SAFETY INFORMATION Vi Safety Instructions r oN Operating Instructions Y S S S S S amp 2 Troubleshooting Tips Consumer Support N N il SPF _ SAFETY PRECAUTIONS This refrigerator must be properly installed and located in accordan
10. OR Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall Push the refrigerator back to the wall START THE ICEMAKER Power switch models Set the icemaker power switch to the I on position The icemaker will not begin to operate until it reaches its operating temperature of 15 F 9 C or below It will then begin operation automatically if the icemaker power switch is in the fon position and the green light will come on Power Switch Icemaker EN Green Power Feeler Arm Light Power switch model IMPORTANT NOTES When reversing the door swing Read the instructions all the way through before starting Handle parts carefully to avoid scratching paint Set screws down by their related parts to avoid using them in the wrong places Provide a non scratching work surface for the doors IMPORTANT Once you begin do not move the cabinet until doorswing reversal is completed These instructions are for changing the hinges from the right side to the left side if you ever want to change the hinges back to the right side follow these same instructions and reverse all references to left and right Unplug the refrigerator from its electrical outlet Empty all door shelves including the dairy compartment START THE ICEMAKER CONT Feeler arm models Move the feeler arm to the ON down position The icemaker will not begin to operate until it re
11. aches its operating temperature of 15 F 9 C or below It will begin operation automatically if the icemaker feeler arm is in the ON down position Sg Ql TN K a R X ne Feeler Arm in the l STOP up position Feeler Arm in the ON down position Feeler arm model NOTE In lower water pressure conditions the water valve may turn on up to 3 times to deliver enough water to the icemaker TOOLS YOU WILL NEED cc ec 2 Phillips screwdriver G6 ES 5 16 Head socket driver 3 4 Head socket driver a 6 point socket is recommended Putty knife or thin blade screwdriver Masking tape Installation Instructions REMOVE THE FREEZER DOOR Tape the door shut with masking tape Remove the hinge cover on top of the freezer door on some models Remove the two screws then lift the hinge straight up to free the hinge pin from the socket in the top of the door Top Hinge pa t Tape the door shut with masking tape Remove the tape and tilt the door away from the cabinet Lift it off the center hinge pin Set the door on a non scratching surface with the inside up 17 REMOVE THE REFRIGERATOR DOOR Tape the door shut with masking tape Remove the center hinge pin with a 3 4 socket Hinge Pin Remove the tape and tilt the door away from the cabinet Lift the door straight off the bottom hinge bracket Set the door on a non scr
12. atching surface with the inside up CAUTION Do not let door drop to the floor To do so could damage the door stop TRANSFER TOP HINGE TO THE LEFT Interchange hinge and screws at top right with screws at the top left of cabinet Do not tighten screws on hinge side at this time TRANSFER BOTTOM HINGE BRACKET TO THE LEFT Remove the base grille by pulling it straight out Using a socket driver move the bottom hinge bracket from the right side to the left side NOTE If the washer is not on the hinge bracket check to see if it is stuck to the bottom of the door C ja we Pe A 18 Installation Instructions REVERSING THE DOOR SWING conrT TRANSFER CENTER HINGE BRACKET TO THE LEFT Remove the center hinge bracket by removing the three screws NOTE Keep these screws with the hinge bracket They are long screws and will be used when installing the hinge on the other side You will need to remove the color matched cap from the screw head before you can remove the screw Use the edge of a thin flat blade to gently pry the caps off the screw heads A putty knife works well for this Cover the blade with tape to prevent scratching the paint Remove the mullion cover from the left side using the thin flat blade Assemble it to the right side Remove the screw from the center left side of the cabinet Screw it into the holes on the right side Place the center hinge b
13. ator with a soiled dish cloth or wet towel These may leave a residue that can erode the paint Do not use scouring pads powdered cleaners bleach or cleaners containing bleach because these products can scratch and weaken the paint finish neutralizes odors Thoroughly rinse and wipe dry Avoid cleaning cold glass shelves on some models with hot water because the extreme temperature difference may cause them to break Handle glass shelves carefully Bumping tempered glass can cause it to shatter Do not wash any refrigerator parts in the dishwasher Wash ice trays in lukewarm water only do not put them in an automatic dishwasher refrigerator in a side direction may result in damage to the floor covering or refrigerator When pushing the refrigerator back make sure you don t roll over the power cord or icemaker supply line on some models Set the icemaker power switch to the 0 off position and shut off the water supply to the refrigerator If the temperature can drop below freezing have a qualified servicer drain the water supply system on some models to prevent serious property damage due to flooding Be sure the refrigerator stays in an upright position during moving suoyonysuy ajes suonanysuy Guyesadg 2 2 Q 3 A S S a sdij Gunooysajqnoy pioddns sauinsuo e Replacing the light bulbs S S Turning the control to the 0 off position does not remove power to the light cir
14. ce must be properly grounded ef HOW TO CONNECT ELECTRICITY suoyanysuy ajes The power cord of this appliance is equipped This provides the best performance and also with a 3 prong grounding plug which mates with prevents overloading house wiring circuits which a standard 3 prong grounding wall outlet to could cause a fire hazard from overheated wires minimize the possibility of electric shock hazard from this appliance Never unplug your refrigerator by pulling on the power cord Always grip plug firmly and pull Have the wall outlet and circuit checked by straight out from the outlet a qualified electrician to make sure the outlet Repai lace i iately all d is properly grounded epair or replace immediately power cords that have become frayed or otherwise damaged If the outlet is a standard 2 prong outlet Do not use a cord that shows cracks or abrasion it is your personal responsibility and obligation damage along its length or at either end to have it replaced with a properly grounded 3 prong wall outlet When moving the refrigerator away from the wall be careful not to roll over or damage the The refrigerator should always be plugged into power cord its own individual electrical outlet which has a voltage rating that matches the rating plate 43 USE OF ADAPTER PL UG S Adapter plugs not permitted in Canada G Because of potential safety hazards under certain conditions we strongly recommend against the use
15. ce with the Installation Instructions before it is used Do not allow children to climb stand or hang on the shelves in the refrigerator They could damage the refrigerator and seriously injure themselves Do not touch the cold surfaces in the freezer READ ALL INSTRUCTIONS BEFORE USING A WARNING Use this appliance only for its intended purpose as described in this Owners Manual When using electrical appliances basic safety precautions should be followed including the following Keep fingers out of the pinch point areas clearances between the doors and between the doors and cabinet are necessarily small Be careful closing doors when children are in the area Unplug the refrigerator before cleaning and making repairs NOTE We strongly recommend that any servicing be compartment when hands are damp or wet performed by a qualified individual Skin may stick to these extremely cold surfaces Setting the controls to the 0 off position does not remove power to the light circuit On some models only the refrigerator control has a 0 off setting Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance Do not refreeze frozen foods which have thawed completely In refrigerators with automatic icemakers avoid contact with the moving parts of the ejector mechanism or with the heating element located on the bottom of the icemaker Do not place fi
16. cuit A amp Refrigerator Compartment at 7 Replace the bulb with an appliance S A CA U TI 0 N Light bulbs may be hot bulb of the same or lower wattage Unplug the refrigerator On models with a light shield replace the light shield The bulbs are located at the top of the refrigerator compartment near the opening On some models a light shield will have to be removed Plug the refrigerator back in 6 To remove the light shield grasp the shield as shown Squeeze the shield and rotate the shield toward the back of the refrigerator The light shield will pop out Operating Instructions Freezer Compartment Light on some models z After replacing with an appliance bulb A CA UTI ON x Light bulbs may be hot of the same or lower wattage replace Unplug the refrigerator the shield The bulb is located behind a light Plug the refrigerator back in shield at the back of the freezer compartment To remove squeeze the top and bottom of the shield and pull the shield off A S S S i B S cS S Freezer Compartment Dome Light on some models oe After replacing with an appliance A CA UTI ON Light bulbs may be hot bulb of the same or lower wattage replace the shield Pocket 7 Unplug the refrigerator 2 The bulb is located at the top of the O Plug the refrigerator back in freezer compartment inside the dome light shield To remove
17. e slide the rack out to the stop position lift the rack up and past the stop position and lift it out Adjustable Humidity Crisper on some models Slide the control all the way to the HIGH setting to provide high humidity recommended for most vegetables Snack Pan on some models This pan can be moved to the most useful location for your family s needs Slide the control all the way to the LOW setting to provide lower humidity levels recommended for most fruits To remove slide the pan out to the stop position lift the pan up and past the stop position and lift it out Adjustable Temperature Deli Pan on some models When the pan is placed in the top 6 slots on the left side and the lever is set at COLDEST air from the freezer is forced around the pan to keep it very cold You can move the pan to any location if you don t want the extra cold storage The settings can be adjusted anywhere between cold pe and coldest pe er When set at cold the pan will stay at the normal refrigerator temperature The coldest setting provides the coldest storage area suoyonysuy ajes suonanysuy Guyesadg A a q Q 3 A S Q 5 a sdij Gurooysajqnosy pioddns saunsuoy Safety Instructions Operating Instructions Power Switch Icemaker A S S S i B S S amp g amp Green Power Light Feeler Arm Power switch model T
18. e refrigerator to move out from the wall after installation 14 INSTALLING THE WATER LINE cont CONNECT THE TUBING TO THE VALVE Place the compression nut and ferrule sleeve for copper tubing onto the end of the tubing and connect it to the shutoff valve Make sure the tubing is fully inserted into the valve Tighten the compression nut securely For plastic tubing from an approved refrigerator tubing kit insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight then tighten one additional turn with a wrench Overtightening may cause leaks Compression Nut Saddle Type Shutoff Valve 4 RS Approved Plastic Tubing Outlet Valve Ferrule sleeve NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber FLUSH OUT THE TUBING Turn the main water supply on and flush out the tubing until the water is clear Shut the water off at the water valve after about one quart 1 liter of water has been flushed through the tubing Installation Instructions CONNECT THE TUBING TO THE CONNECT THE TUBING TO THE REFRIGERATOR REFRIGERATOR CONT NOTES Fasten the tubing into the clamp provided to hold it in a vertical position You may need to pry open the clamp e Before making the connection to t
19. he ON down position On power switch models the green light will come on You will hear a buzzing sound each time the icemaker fills with water The icemaker will fill with water when it cools to approximately 15 F A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes Icemaker Accessory Kit If your refrigerator did not come already equipped with an automatic icemaker an icemaker accessory kit is available at extra cost Throw away the first few batches of ice to allow the water line to clear Be sure nothing interferes with the sweep of the feeler arm When the bin fills to the level of the feeler arm the icemaker will stop producing ice It is normal for several cubes to be joined together If ice is not used frequently old ice cubes will become cloudy taste stale and shrink On power switch models the green power light will blink if ice cubes get stuck in the icemaker To correct this set the power switch to O off and remove the cubes Set the power switch to I on to restart the icemaker After the icemaker has been turned on again there will be a delay of about 45 minutes before the icemaker resumes operation NOTE In homes with lower than average water pressure you may hear the icemaker cycle multiple times when making one batch of ice Check the back of the refrigerator for the specific icemaker kit needed for your model Care and cleaning of the refrigerator
20. he refrigerator be sure the refrigerator power cord is not plugged into the wall outlet 1 4 Tubing e We recommend installing a water filter if your water supply has sand or particles that could clog the screen of the refrigerator s water valve Install it in the water line near the refrigerator If using an approved plastic refrigerator tubing kit 4 Compression Nut you will need an additional tube WX08X10002 to connect the filter Do not cut plastic tube to A Ferrule sleeve install filter b Approved Remove the access cover Plastic Tubing Connection TURN THE WATER ON AT THE SHUTOFF VALVE Tighten any connections that leak Remove the plastic flexible cap from the water valve refrigerator connection Ot Reattach the access cover Place the compression nut and ferrule sleeve onto the end of the tubing as shown On an approved plastic refrigerator tubing kit the nuts are already assembled to the tubing Insert the end of the tubing into the water valve connection as far as possible While holding the tubing tighten the fitting For plastic tubing from an approved plastic refrigerator tubing kit insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight then tighten one additional turn with a wrench Overtightening may cause leaks 15 Installation Instructions INSTALLING THE WATER LINE cont PLUG IN THE REFRIGERAT
21. hin the USA In Alaska the warranty excludes the cost of shipping or service calls to your home Y S S S S S amp 2 Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state To know what your legal rights are consult your local or state consumer affairs office or your state s Attorney General Warrantor General Electric Company Louisville KY 40225 Troubleshooting Tips Consumer Support 24 Safety Instructions Operating Instructions Installation Instructions Troubleshooting Tips Consumer Support 25 www Hotpoint com Notes 26 pioddng sauinsuoy w suonanysuy Ajajes suo n nysuj Guyesadg suonanysuj uonesjeysuy sdi Guooysa qnod Safety Instructions Operating Instructions Installation Instructions Troubleshooting Tips Consumer Support 27 www Hotpoint com Notes Consumer Support Hotpoint Website www Hotpoint com Have a question or need assistance with your appliance Try the Hotpoint Website 24 hours a day any day of the year You can also shop for more great Hotpoint products and take advantage of all of our on line support services designed for your convenience Schedule Service www Hotpoint com Expert Hotpoint repair service is only one step away from your door Get on line and schedule your se
22. ings 3 seconds will be displayed the lock indicator light When the controls are locked the indicator will go out and the settings can be changed light will come on and the control settings will not be displayed Consumer Support About the shelves and bins Not all features are on all models Some models have wire shelves that can be adjusted in the same manner Rearranging the Shelves www Hotpoint com Shelves in the refrigerator and freezer compartments are adjustable Refrigerator Compartment To remove Tilt the shelf up at the front Lift the shelf up at the back and bring the shelf out To replace While tilting the shelf up insert the top hook at the back of the shelf in a slot on the track Lower the front of the shelf until the bottom of the shelf locks into place Freezer Compartment To remove Lift up the left side of the shelf and slide it left into the center of the shelf supports Rotate the right side of the shelf up and out of the shelf supports To replace Holding the shelf diagonally insert the left end of the shelf into the center of the shelf supports on the side wall at the desired level Insert the right end of the shelf into the shelf supports at the same level Rest each end of the shelf on the bottom of the shelf supports Spillproof Shelves on some models Spillproof shelves have special edges t
23. l water pipe make the connection to the top or side rather than at the bottom to avoid drawing off any sediment from the water pipe 1 DRILL THE HOLE FOR THE VALVE Drill a 1 4 hole in the water pipe even if using a self piercing valve using a sharp bit Remove any burrs resulting from drilling the hole in the pipe Take care not to allow water to drain into the drill Failure to drill a 1 4 hole may result in reduced ice production or smaller cubes Installation Instructions FASTEN THE SHUTOFF VALVE Fasten the shutoff valve to the cold water pipe with the pipe clamp Pipe Clamp y lt Saddle Type ES Shutoff Valve Vertical Cold Water Pipe NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber TIGHTEN THE PIPE CLAMP Tighten the clamp screws until the sealing washer begins to swell NOTE Do not overtighten or you may crush the tubing Pipe Clamp A Clamp Screw 6 ROUTE THE TUBING Route the tubing between the cold water line and the refrigerator Route the tubing through a hole drilled in the wall or floor behind the refrigerator or adjacent base cabinet as close to the wall as possible NOTE Be sure there is sufficient extra tubing about 8 feet 244 cm coiled into 3 turns of about 10 25 cm diameter to allow th
24. le Move the plug button on the right side of the door to the handle screw hole on the left side Reattach the handle on the opposite side using the holes closest to the edge of the door _ SNS 20 REVERSING THE DOOR SWING contr REHANG THE REFRIGERATOR DOOR Lower the refrigerator door onto the bottom hinge pin Straighten the door and line it up with the center hinge bracket Reinstall the center hinge pin with a 3 4 socket Turn it until it extends through the hinge bracket and into the door Hinge Pin gt REHANG THE FREEZER DOOR Lower the freezer door onto the center hinge pin Lift the top hinge so the pin fits into the door socket Support the door on the handle side and make sure the door is straight and the gap between the doors is even across the front While holding the door in place tighten the top hinge screws Normal operating sounds Q technology www Hotpoint com Newer refrigerators sound different from older refrigerators Modern refrigerators have more features and use newer Do you hear what hear These sounds are normal HUMMM WHOOSH E The new high efficiency compressor may run faster and longer than your old refrigerator and you may hear a high pitched hum or pulsating sound while it is operating H You may hear a whooshing sound when the doors close This is due to pressure equalizing within the refrigerat
25. ll e 1 2 or adjustable wrench Straight and Phillips blade screwdriver Two 1 4 outer diameter compression nuts and 2 ferrules sleeves to connect the copper tubing to the shutoff valve and the refrigerator water valve OR If you are using an approved plastic refrigerator tubing kit the necessary fittings are preassembled to the tubing If your existing copper water line has a flared fitting at the end you will need an adapter available at plumbing supply stores to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting Do not cut formed end from approved plastic refrigerator tubing Shutoff valve to connect to the cold water line The shutoff valve should have a water inlet with a minimum inside diameter of 5 32 at the point of connection to the COLD WATER LINE Saddle type shutoff valves are included in many water supply kits Before purchasing make sure a saddle type valve complies with your local plumbing codes 13 Install the shutoff valve on the nearest frequently used drinking water line SHUT OFF THE MAIN WATER SUPPLY Turn on the nearest faucet long enough to clear the line of water CHOOSE THE VALVE LOCATION Choose a location for the valve that is easily accessible It is best to connect into the side of a vertical water pipe When it is necessary to connect into a horizonta
26. ngers or hands on the automatic icemaking mechanism while the refrigerator is plugged in A DANGER RISK OF CHILD ENTRAPMENT PROPER DISPOSAL OF THE REFRIGERATOR Child entrapment and suffocation are not Refrigerants problems of the past Junked or abandoned refrigerators are still dangerous even if they will sit for just a few days If you are getting rid of your old refrigerator please follow the instructions below to help prevent accidents All refrigeration products contain refrigerants which under federal law must be removed prior to product disposal If you are getting rid of an old refrigeration product check with the company handling the disposal about what to do Before You Throw Away Your Old Refrigerator or Freezer Take off the doors Leave the shelves in place so that children may not easily climb inside USE OF EXTENSION CORDS Because of potential safety hazards under certain conditions we strongly recommend against the use of an extension cord However if you must use an extension cord it is absolutely necessary that it be a UL listed in the United States or a CSA listed in Canada 3 wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes minimum and 120 volts www Hotpoint com Do not under any circumstances cut or remove the third ground prong from the power cord For personal safety this applian
27. o help prevent spills from dripping to lower shelves To remove or replace the shelves see Rearranging the Shelves NOTE For models with an automatic icemaker the freezer shelf must be in the lower position for the ice cube bucket to catch the cubes suoyonysuy ajes suonaonysuy Guyesadg A 2 Q 3 A S S a sdij Gurooysajqnosy pioddns sauinsuoy Safety Instructions Operating Instructions A S S S i B S S amp amp Troubleshooting Tips Consumer Support About the shelves and bins Slide Out Spillproof Shelf on some models The slide out spillproof shelf allows you to reach items stored behind others The special edges are designed to help prevent spills from dripping to lower shelves To remove Q Remove all items from shelf Slide the shelf out until it stops Lift the front edge of the shelf until the central tabs are above the front bar 4 Continue pulling the shelf forward until it can be removed Adjustable Bins on the Door Adjustable bins can easily be carried from refrigerator to work area To remove Lift the bin straight up then pull out To replace or relocate Engage the bin in the molded supports of the door and push in Bin will lock in place Non Adjustable Shelves on the Door To remove Lift the shelf straight up then pull out To replace Engage the shelf in the molded supports on the door and push down
28. o not install the refrigerator where the temperature will go above 100 F 37 C because it will not perform properly e Install it on a floor strong enough to support it fully loaded 11 CLEARANCES Allow the following clearances for ease of installation proper air circulation and plumbing and electrical connections e Sides 1 8 4 mm e Top 1 25 mm e Back 1 25 mm If the refrigerator is against a wall on either side allow a 1 8 3 mm door clearance ROLLERS The rollers have 3 purposes E Rollers adjust so the doors close on their own when opened about 45 E Rollers adjust so the refrigerator is firmly positioned on the floor and does not wobble E Rollers allow you to move the refrigerator away from the wall for cleaning To adjust the rollers 7 Remove the base grille by positioning hands as shown Rotate the bottom of the grille outward until the clips snap out Pull the grille away from the refrigerator Using a screwdriver turn the two front roller adjusting screws clockwise to raise the refrigerator counterclockwise to lower it Replace the grille so the notch in the grille will fit around the bottom door hinge Tilt the top of the grille toward the refrigerator and insert the long metal clips into the top of the oval openings at the bottom of the refrigerator Rotate the bottom of the grille toward the refrigerator until it snaps into place Installation
29. of an adapter plug suononysuy Guyesadg However if you must use an adapter where local If the adapter ground terminal breaks DO NOT USE codes permit a temporary connection may be made the refrigerator until a proper ground has been to a properly grounded 2 prong wall outlet by use established of a UL listed adapter available at most local hardware stores A 2 Q 3 A S S a Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the cover screw The larger slot in the adapter must be aligned with is metal and not insulated and the wall outlet is grounded the larger slot in the wall outlet to provide proper through the house wiring You should have the circuit checked polarity in the connection of the power cord by a qualified electrician to make sure the outlet is properly grounded When disconnecting the power cord from the adapter always hold the adapter in place with one hand while pulling the power cord plug with the other hand If this is not done the adapter ground terminal is very likely to break with repeated use sdiy Gunooysajqnosy Vis Z READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY oO SAVE THESE INSTRUCTIONS pioddns sauinsuoy About the controls on the refrigerator The controls will look like one of the following ADJUST FREEZER TEMP ACTIVATE LOCK ADJUST REFRIGERATOR TEMP 5 G amp G FG 9 Is COLDEST O Is COLDEST
30. or Electronic models only H Sometimes the refrigerator runs for an extended period especially when the doors are opened frequently This means that the Frost Guard feature is working to prevent freezer burn and improve food preservation WHIR E You may hear the fans spinning The fans help to maintain the correct temperatures Electronic models only E You may hear the fans spinning at high speeds This happens when the refrigerator is first plugged in when the doors are opened frequently or when a large amount of food is added to the refrigerator or freezer compartments E If either door is open for over 3 minutes you may hear the fans come on in order to cool the light bulbs E The fans change speeds in order to provide optimal cooling and energy savings CLICKS POPS CRACKS and CHIRPS E You may hear cracking or popping sounds when the refrigerator is first plugged in This happens as the refrigerator cools to the correct temperature E The compressor may cause a clicking or chirping sound when attempting to restart this could take up to 5 minutes E The electronic control board may cause a clicking sound when relays activate to control refrigerator components H Expansion and contraction of cooling coils during and after defrost can cause a cracking or popping sound E On models with an icemaker after an icemaking cycle you may hear the ice cubes dropping into the ice bucket WATER SOUN
31. proper servicing may cause unsafe operation Contact Us www Hotpoint com KoA If you are not satisfied with the service you receive from Hotpoint contact us on our Website with all the details including your phone number or write to General Manager Customer Relations Hotpoint Appliance Park Louisville KY 40225 Register Your Appliance www Hotpoint com Register your new appliance on line at your convenience Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty should the need arise You may also mail in the pre printed registration card included in the packing material Printed in Mexico
32. r supply turned off or not connected e See Installing the water line Freezer compartment too warm e Wait 12 24 hours for the refrigerator to completely cool down Piled up cubes in the storage bin cause the icemaker to shut off e Level cubes by hand Ice cubes stuck in icemaker Green power light on icemaker blinking Icemaker power switch is in the on position but the water supply to the refrigerator has not been connected e Turn off the icemaker remove cubes and turn the icemaker back on e Set the power switch to the 0 off position Keeping it in the on position will damage the water valve Problem Ice cubes have odor taste Slow ice cube freezing No ice cube production Refrigerator has odor Possible Causes Ice storage bin needs cleaning www Hotpoint com What To Do e Empty and wash bin Discard old cubes Food transmitting odor taste to ice cubes e Wrap foods well Interior of refrigerator needs cleaning Door left open e See Care and cleaning e Check to see if package is holding door open Temperature control not set cold enough Supply line or shutoff valve is clogged Foods transmitting odor to refrigerator e See About the controls e Call a plumber e Foods with strong odors should be tightly wrapped Keep an open box of baking soda in the refrigerator replace every three months Interior needs cleaning
33. racket over the holes at the center left side of the cabinet Insert and tighten the three long screws Replace the cap by snapping it over the screw with your finger Screw Cap Mullion Cover 6 TRANSFER DOOR STOPS On each door move the metal door stop from the right to the left Move any screws from the left to the right Installation Instructions TRANSFER REFRIGERATOR DOOR HANDLE TO THE RIGHT To remove the handle Remove the plug button by carefully prying under the edge with a putty knife Remove the exposed screw holding the handle g Handle Plug Remove the two screws holding the handle to the top of the door Long Handle Short Handle After removing the handle Move the small plug buttons from the top right side of the door top and insert them into the holes on the opposite side Small Plug Buttons Move the large plug button from the left edge of the door and insert it into the hole on the opposite side Plug Button 19 TRANSFER REFRIGERATOR DOOR HANDLE TO THE RIGHT CONT Transfer the door plug button to the opposite side Button Reinstalling the handle Attach the handle to the right side of the door Long Handle Short Handle Handle Plug ee Installation Instructions TRANSFER FREEZER DOOR HANDLE TO THE RIGHT Remove the screws holding the handle to the top and bottom of the door Remove hand
34. roubleshooting Tips h Feeler Arm in the STOP Feeler Armin up position the ON down position Feeler arm model Consumer Support About crisper removal Not all features are on all models Crisper Removal To Remove These drawers can be removed easily by lifting up slightly while pulling the drawer past the stop location When the door cannot be fully opened remove the drawer farthest from the door first Make sure the drawer closest to the door is fully closed There is a latch at the front of the center slide rail Push down on the latch and slide the center slide rail to which the drawer is attached away from the door Remove the drawer About the automatic icemaker A newly installed refrigerator may take 12 24 hours to begin making ice Automatic Icemaker on some models The icemaker will produce seven or eight cubes depending on model per cycle approximately 100 130 cubes in a 24hour period depending on freezer compartment temperature room temperature number of door openings and other use conditions There are two types of icemakers power switch models and feeler arm models If the refrigerator is operated before the water connection is made to the icemaker set the power switch to O off or move the feeler arm to the STOP up position When the refrigerator has been connected to the water supply set the power switch to the on position or move the feeler arm to t
35. rvice at your convenience 24 hours any day of the year Or call 800 GE CARES 800 432 2737 during normal business hours Real Life Design Studio www GEAppliances com GE supports the Universal Design concept products services and environments that can be used by people of all ages sizes and capabilities We recognize the need to design for a wide range of physical and mental abilities and impairments For details of GE s Universal Design applications including kitchen design ideas for people with disabilities check out our Website today For the hearing impaired please call 800 TDD GEAC 800 833 4322 Extended Warranties www GEAppliances com Purchase a Hotpoint extended warranty and learn about special discounts that are available while your warranty is still in effect You can purchase it on line anytime or call 800 626 2224 during normal business hours Hotpoint Consumer Home Services will still be there after your warranty expires Parts and Accessories www Hotpoint com Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes VISA MasterCard and Discover cards are accepted Order on line today 24 hours every day or by phone at 800 626 2002 during normal business hours Instructions contained in this manual cover procedures to be performed by any user Other servicing generally should be referred to qualified service personnel Caution must be exercised since im
36. the shield place your finger in the pocket at the back of the shield Pull the shield forward and down Troubleshooting Tips Consumer Support 10 Installation Instructions Refrigerator Models 22 and 25 Questions Call 800 GE CARES 800 432 2737 or Visit our Website at www Hotpoint com BEFORE YOU BEGIN Read these instructions completely and carefully e IMPORTAN T Save these instructions for local inspector s use hg IMPORTAN T Observe all governing codes and ordinances e Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions for future reference e Skill level Installation of this appliance requires basic mechanical skills e Completion time Refrigerator Installation 15 minutes e Proper installation is the responsibility of the installer e Product failure due to improper installation is not covered under the Warranty WATER SUPPLY TO THE ICEMAKER ON SOME MODELS If the refrigerator has an icemaker it will have to be connected to a cold water line A water supply kit containing tubing shutoff valve fittings and instructions is available at extra cost from your dealer or from Parts and Accessories 800 626 2002 REFRIGERATOR LOCATION e Do not install the refrigerator where the temperature will go below 60 F 16 C because it will not run often enough to maintain proper temperatures e D
37. y Review the charts on the following Possible Causes Refrigerator in defrost cycle pages first and you may not need to call for service What To Do e Wait about 40 minutes for defrost cycle to end The controls are set to the 0 off position e Move the refrigerator and freezer control to a temperature setting Refrigerator is unplugged e Push the plug completely into the outlet The fuse is blown circuit breaker is tripped Rollers need adjusting Normal when refrigerator is first plugged in e Replace fuse or reset the breaker e See Rollers e Wait 12 24 hours for the refrigerator to completely cool down Often occurs when large amounts of food are placed in refrigerator e This is normal Door left open e Check to see if package is holding door open Hot weather or frequent door openings e This is normal Temperature controls set at the coldest setting Temperature control not set cold enough e See About the controls e See About the controls Warm weather or frequent door openings e Set the temperature control one step colder See About the controls Door left open Door left open e Check to see if package is holding door open Check to see if package is holding door open Too frequent or too long door openings Icemaker power switch is in the 0 off position Set the power switch to the on position Wate
Download Pdf Manuals
Related Search