Hitachi D 13VB3 Drill User Manual
Contents
1. Slip clutch mechanism This unit contains a slip clutch that causes the gears between the motor and drill bit to slip when an excessive load is suddenly applied The slip clutch protects the unit from a large violent reaction the load might cause CAUTION O Ifthe slip clutch triggers and stops the drill bit rotation quickly turn off the power switch O Do not operate the unit in a way that frequently triggers the slip clutch MAINTENANCE AND INSPECTION 1 Inspecting the drill bits Since use of an abraded drill bits will cause motor malfunctioning and degraded efficiency replace the drill bits with a new one or resharpening without delay when abrasion is noted 2 Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened Should any of the screws be loose retighten them immediately Failure to do so could result in serious hazard 3 Maintenance of the motor The motor unit winding is the very heart of the power tool Exercise due care to ensure the winding does not become damaged and or wet with oil or water 4 Inspecting the carbon brushes For your continued safety and electrical shock protection carbon brush inspection and replacement on this tool should ONLY be performed by a Hitachi Authorized Service Center 5 Replacing supply cord If the supply cord of Tool is damaged the Tool must be returned to Hitachi Authorized Service Center for the2. 145 YVAD Nid Wav L4IHS LAVHS 91 3dAL 3 DNIY ONINIVLAY ged Mva 13315 DNIH4S A SSV Y3A31 LAIHS 1 LAIHS Nid 5 22 S DNIY O YANNI 9 NOINId ANOI3S 9 YIHSVM YVID StXSA ADNV14 M MIYIS DNIdAVL L4VHS 91 ONINIVL38 TZSINIAAZOZI TIVE SEC HOS 1994 9 310NIAS TIYA HIN3Y4M ADNHD 9 9 1437 VW M389S 1919 Med O Hitachi Koki Co Ltd Shinagawa Intercity Tower A 15 1 Konan 2 chome Minato ku Tokyo Japan 905 Code No C99136412 E Printed in Ireland
3. Attach the side handle to the mounting part Rotate the side handle grip in a clockwise direction to secure it Set the side handle to a position that is suited to the operation and then securely tighten the side handle grip Side handle Loosen as Tighten U Fig 5 To attach a depth gauge on the side handle insert the gauge into the U shaped groove on the side handle adjust the position of the depth gauge in accordance with the desired depth of the hole and firmly tighten the side handle grip Fig 6 Depth gauge Side handle Loosen o gt Tighten Fig 6 8 High speed Low speed changeover Prior to changing speed ensure that the switch is in the OFF position and the drill has come to a complete stop To change speed rotate the gear shift dial as indicated by the arrow in Fig 7 The numeral 1 engraved on the drill body denotes low speed the numeral 2 denotes high speed If it is hard to turn the gear shift dial turn the chuck slightly in either direction and then turn the gear shift dial again HOW TO USE 1 Switch operation When the trigger is depressed the tool rotates When the trigger is released the tool stops O The rotational speed of the drill can be controlled by varying the amount that the trigger switch is pulled Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more The desired rotation speed can be pre select
4. cord to be replaced 6 Service parts list CAUTION Repair modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance In the operation and maintenance of power tools the safety regulations and standards prescribed in each country must be observed MODIFICATION Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements Accordingly some parts may be changed without prior notice NOTE Due to HITACHI s continuing program of research and development the specifications herein are subject to change without prior notice 39NV9 H1d30 JANVH AIS ayoo AYOI 9 ADNV14 M MIYIS DNIdAVL 3718 1109 3NOH9 199 30719 SHIM TVNY3LNI HL4V3 55 4 5 SION 13971 IHOVLIH Y3010H HSnya Hsnya NOgyvo NMOY8 1109 1001 NMOY8 34IM TVNY3LNI HOLIMS NOLLNG ONIHSNd Y43409 FIANVH 02Xra ADNV14 M MIYIS DNIddVL 3LVId3NVN DNISNOH DNIHSNI y3gany 1ZSN AZIWLZZX11869 Iva YOLVLS MAYOS DNIddV L GH X3H 23629 DNIYV39 TIVE HILNTI dS 139771
5. of stuff liable to roll up such as cotton wool cloth or string etc 4 110 220 230 240 V Power input 790 W Speed change 1 2 Forward rotation 0 1000 min 0 3000 min No load speed Reverse rotation 0 600 min 0 1800 min Steel 13 mm 8mm Capacity Wood 00 40 mm 25 mm Weight without cord STANDARD ACCESSORIES 1 Chuck Wrench Spec only for keyed chuck 2 Side Handle 3 Depth Gauge Standard accessories are subject to change without notice APPLICATIONS O Boring holes in metal wood and plastic PRIOR TO OPERATION 1 Power source Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate Power switch Ensure thatthe power switch is in the OFF position If the plug is connected to a receptacle while the power switch is in the ON position the power tool will start operating immediately inviting serious accident Extension cord When the work area is removed from the power source use an extension cord of sufficient thickness and rated capacity The extension cord should be kept as short as practicable Selecting the appropriate drill bit When boring metal or plastic Use an ordinary metalworking drill bit When boring wood Use an ordinary woodworking drill bit However when drilling 6 5 mm or smaller holes use a metalworking drill bit
6. HITACHI Drill Model D 13VB3 Handling instructions Before using this Electric Power Tool carefully read through these HANDLING INSTRUCTIONS to ensure efficient safe operation It is recommended that these INSTRUCTIONS be kept readily available as an important reference when using this power tool Hitachi Koki GENERAL SAFETY RULES WARNING Read all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the warnings listed below refers to your mains operated corded power tool or battery operated cordless power tool SAVE THESE INSTRUCTIONS 1 Work area a Keep work area clean and well lit Cluttered and dark areas invite accidents b Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust of fumes c Keep children and bystanders away while operating a power tool Distractions can cause you to lose control 2 Electrical safety a Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock b Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric sh
7. Mounting and dismounting of the bit For keyed chuck Fig 1 1 Open the chuck jaws and insert the bit into the chuck OF 5 2 Place the chuck wrench in each of the three holes in the chuck and turn it in the clockwise direction viewed from the front side Tighten securely 3 To remove the bit place the chuck wrench into one of the holes in the chuck and turn it in the counterclockwise direction Drill chuck Chuck wrench Tighten A Loosen Fig 1 Fig 2 For keyless chuck 1 Mounting the bit Turn the sleeve counterclockwise and open the chuck After inserting the drill bit into the chuck as far it will go grip the ring and close the chuck by turning the sleeve clockwise as viewed from the front 2 Dismounting the bit Grip the ring and open the chuck by turning the sleeve counterclockwise Sleeve Ring Loosen NOTE When the sleeve does not become loose any further fix the side handle to ring hold side handle firmly then turn the sleeve to loosen by hand Fig 3 Side handle Fig 3 6 Check the rotational direction Fig 4 The bit rotates clockwise viewed from the rear side by pushing the R side of the push button The L side ofthe push button is pushed to turn the bit counterclockwise The L and 8 marks are provided on the body D L mark 4 Push button Switch trigger R mark Fig 4 7 Fixing the side handle Fig 5
8. ed with the speed control dial Turn the speed control dial clockwise for higher speed and counterclockwise for lower speed Fig 8 Pulling the trigger and pushing the stopper it keeps the switched on condition which is convenient for continuous running When switching off the stopper can be disconnected by pulling the trigger again CAUTION If the L side of push button is pressed for reverse bit rotation the stopper cannot be used Speed control dial Low speed Switch trigger Fig 8 Drilling When drilling start the drill slowly and gradually increasing speed as you drill O Always apply pressure in a straight line with the bit Use enough pressure to keep drilling but do not push hard enough to stall the motor or deflect the bit O minimize stalling or breaking through the material reduce pressure on drill and ease the bit through the last part of the hole If the drill stalls release the trigger immediately remove the bit from the work and start again Do not click the trigger on and off in an attempt to start a stalled drill This can damage the drill O The larger the drill bit diameter the larger the reactive force on your arm Be careful not to lose control of the drill because of this reactive force To maintain firm control establish a good foothold use side handle hold the drill tightly with both hands and ensure that the drill is vertical to the material being drilled ON
9. ls Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tools operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools f Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could result in a hazardous situation b d g Service a Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained PRECAUTION Keep children and infirm persons away When not in use tools should be stored out of reach of children and infirm persons PRECAUTIONS ON USING DRILL 1 Wear ear protectors with impact drills Exposure to noise can cause hearing loss SPECIFICATIONS Voltage by areas 2 Use auxiliary handles supplied with the tool Loss of control can cause personal injury 3 Before drilling into walls ceilings or floors ensure that there are no concealed power cables inside Do not wear gloves made
10. ock if your body is earthed or grounded c Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock d Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock e When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock f Recommendation for the use of residual current device with a rated residual current of 30mA or less 3 Personal safety a Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury b Use safety equipment Always wear eye protection Safety equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries 4 5 c Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the power to
11. ol on A wrench or a key left attached to a rotating part of the power tool may result in personal injury e Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations f Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of these devices can reduce dust related hazards d g Power tool use and care a Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired c Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users e Maintain power too
Download Pdf Manuals
Related Search