Henny Penny CMC/CMR-105 Refrigerator User Manual
Contents
1. flashes in display 2 to change the temperature setpoint Press the 8 Sor within 5 seconds After 5 seconds the last entered setpoint stays in memory Press to access the other parameters Each press of the accesses the next parameter The parameters d differential 15 15 range LS lower set lower user access setpoint limit 55 99 range CAUTION The units are programmed to defrost 3 times a day at 8 hour intervals lasting 30 minutes Do not program the setpoint temperature below 33 F 1 C or ice build up will decrease efficiency HS higher set upper user access setpoint limit 55 99 range CA calibration temperature readout offset to allow for possible error due to probe location 15 15 range rP relay protection select relay status in case of probe defect compressor on in case of probe defect of compressor off in case of probe defect PS protection system short cycle select type of compressor protection desired the actual time delay is set with the next parameter 0 delay before start in seconds 1 delay before start in minutes 2 delay after stop in minutes 3 delay between starts in minutes Pt protection time select the time delay setting for compres sor protection 0 31 range 303 Y P Global Foodservice ENNY Solutions PROGRAMMING 3 5 303 Continued ds Mo2. PENNY Global Foodservice Solutions Henny Penny Cold Tops Model CMC CMR 103 Model CMC CMR 104 Model CMC CMR 105 Model CMC CMR 106 Model CMC CMR 107 OPERATOR S MANUAL ES Y PENNY Model CMC CMR 103 104 105 106 107 Global Foodservice Solutions LIMITED WARRANTY FOR HENNY PENNY APPLIANCES Subject to the following conditions Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Penny appliances and replacement parts NEW EQUIPMENT part of a new appliance except lamps and fuses which proves to be defective in material or workmanship within two 2 years from date of original installation will be repaired or replaced without charge F O B factory Eaton Ohio or F O B authorized distributor To validate this warranty the registration card for the appliance must be mailed to Henny Penny within ten 10 days after installation REPLACEMENT PARTS Any appliance replacement part except lamps and fuses which proves to be defective in material or workmanship within ninety 90 days from date of original installation will be repaired or replaced without charge F O B factory Eaton Ohio or F O B authorized distributor The warranty for new equipment and replacement parts covers only the repair or replacement of the defective part and does not include any labor charges for the removal and installation of any parts travel or other expenses incidental to the re
3. Cold Base Installation Instructions i 2 7 lc 3 1 INTO ri lia 3 1 Operating Controls 3 1 206 Basic Operati OM ssion eanne R 3 3 3 3 it 3 5 Fluorescent Bulb Repl cement ina 3 7 3 8 Genuine T tanda E 4 1 HOW t Order ns 4 1 Pcia oia 4 1 d TR 4 1 IATA lia nn a 4 1 Recommended Spare Parts for Distributors eene 4 1 Model CMC CMR 103 104 105 106 107 RS A li 1 1 COLD TOPS The Henny Penny cold tops are full service units designed to hold chilled or refrigerated products The units are electronically controlled for easy use and for consistent operation 1 2 FEATURES be matched with hot or cold merchandisers in all lengths Electronic Controls Stackable units on top of bases Low speed air circulation Easily maintained e Fluorescent lighting with electronic ballast CE magnetic ballast Mirrored or clear side glass Full service units Remote or self contained condenser models Insulated well with high pressure injected polyurethane foam Automat
4. be careful not to damage the refrigerent circuit Any shipping damage should be noted in the presence of the delivery agent and signed prior to his or her departure To remove the Henny Penny cold top from the carton 1 2 3 Carefully cut banding straps Lift the carton off the unit Remove bolts securing the cold top to the skid and lift the unit off the skid 2 1 Global Foodservice ENNY Solutions UNPACKING 2 2 2 3 ELECTRICAL 2 2 Continued Model CMC CMR 103 104 105 106 107 HEAVY OBJECT Take care when moving the fryer to prevent personal injury or damage to the refrigeration system The CMC 107s weigh over 700 lbs 318 kg 4 Peel off any protective covering from exterior of the cabinet 5 Install the grids into unit 6 Unpack sliding thermal doors and side glass Install on rear and side of unit 7 Your cold top is now ready for operation The Cold Top is available as a 120 VAC 60 Hz or 230VAC 50 Hz single phase unit both for domestic and international use The data plate located beside the power cord specifies the correct electrical supply The Cold Tops are shipped with cord and plug and requires a grounded receptacle with a separate electrical line protected by a fuse or circuit breaker of the proper rating Position the unit so the power cord receptacle is accessible SHOCK HAZARD To avoid electrical shock this appliance must be equ
5. 10 Global Foodservice Y P ENNY Solutions Model CMC CMR 103 104 105 106 107 SECTION 4 PARTS INFORMATION 4 1 INTRODUCTION 4 2 GENUINE PARTS 4 3 HOW TO ORDER 4 4 PRICES 4 5 DELIVERY 4 6 WARRANTY 4 7 RECOMMENDED SPARE PARTS FOR DISTRIBUTORS 4 1 This section identifies and lists the replaceable parts of the Henny Penny Cold Top Use only genuine Henny Penny parts in your cabinet Using a part of lesser quality or substitute design may result in cabinet damage or personal injury Once the part you want to order has been found in the Parts List write down the following information 1 Fromthe Parts List Sample Ttem Number 1 Part Number 56242 001 Description Side Glass Flat Clear 2 From the data plate Sample Product Number CMC 100 Serial Number 0001 Voltage 120V Your distributor has a price parts list and will be glad to inform you of the cost of your parts order Commonly replaced items are stocked by your distributor and will be sent out when your order is received Other parts will be ordered by your distributor from Henny Penny Corpora tion Normally these will be sent to your distributor within three working days Allreplacement parts except lamps and fuses are covered under warranty for 90 days against manufacturing defects and workmanship If damage occurs during shipping notify the carrier at once so that a claim may be properly filed Refer to warranty on the fron
6. 134A R134A R134A R134A 1 65 Ibs 0 750 kg 1 87 lbs 0 850 kg 2 65 lbs 1 200 kg 3 09 Ibs 1 400 kg 3 53 lbs 1 600 kg Design Pressure High 440psig 30 3 bar 440psig 440psig 30 3 bar 440psig 30 3 bar 440psig 30 3 bar 440psig 30 3 bar 440psig 30 3 bar 440psig 30 3 bar 440psig 30 3 bar 440psig 30 3 bar Low 162 psig 11 2 bar 162 psig 162 psig 11 2 bar 162 psig 11 2 bar 162 psig 11 2 bar 162 psig 11 2 bar 162 psig 11 2 bar 162 psig 11 2 bar 162 psig 11 2 bar 162 psig 11 2 bar The cold tops remote CMRs requires 1 1 2 inch 38 1 mm drain connection CMCs do not require a plumbed drain 2 3 Y PENNY Model CMC CMR 103 104 105 106 107 Global Foodservice Solutions 2 7 COMPRESSOR SIZE AND LOAD Model CMC Motor HP CMR Motor HP CMC BTU Load UL CE UL CE CMR R 22 R 134a R 22 R 134a Remote Compressor Supplied By Other BIU load sized at evaporator temperature 20 For 6 2 8 FOOT PRINT DRAWING CMR MODELS DRAIN amp REFRIGERATION CONNECTIONS x BOUT END 2 4 303 Model CMC CMR 103 104 105 106 107 Y PENNY Global Foodservice 2 9 CUT OUT DIMENSIONS FOR DRY BASE OR TABLE INSTALLATION 1 Be EE WT 3 VIEW diia 6 oq qo io i I ream Li mm 1 3 1 mm e 29 mn mir Lo
7. 300N Gas Ram 400N Gas Ram 500N Model CMC CMR 103 104 105 106 107 Quantity 103 104 105 106 107 See chart on page 4 3 See chart on page 4 3 See chart on page 4 3 See chart on page 4 3 See chart on page 4 3 4 4 222 Q RQ Q RQ m m 2 2 2 2 22 e S 22 ea Ni e e me e e e pa a DI NH HA HA HW LI W 4 Global Foodservice Y P 23967 23969 23968 23973 23971 23972 23970 23996 23979 23980 23981 23982 23983 23985 65045 65046 65047 65048 23986 23998 23991 23992 23993 24146 24147 23999 24144 24145 37224 58574 31399 58567 14634 67019 67020 21950 67018 21951 67017 58550 67215 ENNY Solutions RECOMMENDED PARTS LIST Description Refrigeration unit 1 4 HP CMC 103 104 Refrigeration unit 1 3 HP CMC 105 106 Refrigeration unit 1 2 HP CMC 107 Evaporator 152 24 CMC CMR 103 Evaporator CMC CMR 104 Evaporator CMC CMR 105 Evaporator CMC CMR 106 Evaporator CMC CMR 107 Therm Expansion Valve R22 CMC CMR 103 104 105 106 Therm Expansion Valve R22 CMC CMR 107 Filter Drier Moisture amp Liquid Indicator 1 4 SAE male Kit Fan amp Blade 4 1 2 black Electronic Control Eliwell Complete 12V EWPC961 Front cover amp Bezel Eliwell Control F Sensor Probe Eliwell 120V 12V Transformer Eliwell 120V12V Control amp Bracket Eliwell 120V 12V Sylvania Q
8. 303 H PENNY Global Foodservice Solutions 3 2 OPERATING CONTROLS Continued 303 Figure 3 1 Model CMC CMR 103 104 105 106 107 Y PENNY Global Foodservice Solutions 3 3 BASIC OPERATION 3 4 CLEANING 3 3 Model CMC CMR 103 104 105 106 107 Turn power switch to ON position Wait for temperature to reach operating temperature 34 to 38 F 1 1 to 3 3 C Place chilled product into case Do not block the air return and air discharge vents with product Product temperatures may become unsafe and increase operating costs Do not use mechanical devices or other means to quicken the defrosting process other than those recommended by the manufacturer or damage to the unit could result Do not use electrical appliances inside the food storage areas of the unit unless they are of the type recommended by the manufacturer or damage to the unit could result Weekly 1 Remove all electrical power supplied to the unit by unplug ging the power cord from the wall or by turning off the wall circuit breaker Clean interior and exterior surfaces with a soft cloth soap and B CAUTION Do not use steel wool other abrasive cleaners or cleaners sanitizers containing chlorine bromine iodine or ammonia chemicals as these will deteriorate the stainless steel and glass material and shorten the life of the unit Do not use a water jet pressure sprayer to clean the unit or component fa
9. 5 well Full Serve 2 400N 4 500N 2 58607 035 Flat Profile 6 well Full Serve 2 per unit 2 400N 2 500N 2 58607 036 Flat Profile 7 well Full Serve 2 per unit 2 200N 4 300N 2 58607 046 TYLER Advantage Profile 2 well Full Serve 2 300N 2 400N 2 58607 047 TYLER Advantage Profile 3 well Full Serve 4 200N 2 300N 2 58607 048 TYLER Advantage Profile 4 well Full Serve 6 400N 2 58607 049 TYLER Advantage Profile 5 well Full Serve 6 500N 2 58607 050 TYLER Advantage Profile 6 well Full Serve 2 per unit 4 500N 2 58607 051 TYLER Advantage Profile 7 well Full Serve 2 per unit 6 300N 2 58607 061 Hussman Vision Profile 3 well Full Serve Non Glare 2 300N 4 400N 2 58607 062 Hussman Vision Profile 5 well Full Serve Non Glare 4 400N 4 500N 2 58607 063 Hussman Vision Profile 7 well Full Serve Non Glare 2 per unit 4 400N 2 500N 2 58607 064 Flat Profile 3 Well Non Glare 4 500N 2 58607 065 Flat Profile 5 Well Non Glare 2 400N 4 500N 2 58607 066 Flat Profile 7 Well Non Glare 2 per unit 2 200N 4 300 Item Part Quantity No No Description 103 104 105 106 107 3 MS01 366 not shown 4 3 Gasket Handle Canopy Glass order per foot 1101 H PENNY Global Foodservice Solutions Item No Part No 56878 56343 001 56343 002 56343 003 56343 004 56343 005 Description Gas Shock Tool Gas Ram 100N Gas Ram 200N Gas Ram
10. MS FOR ANY INCIDENTAL OR CONSQUENTIAL DAMAGES SHALL BE AVAIL ABLE The above limited warranty does not apply a to damage resulting from accident alteration misuse or abuse b if the equipment s serial number is removed or defaced or c for lamps and fuses THE ABOVE LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUD ING MERCHANTABILITY AND FITNESS AND ALL OTHER WARRANTIES ARE EXCLUDED HENNY PENNY NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY OTHER OB LIGATION OR LIABILITY 01 878 Revised 02 09 06 Y PENNY Global Foodservice Solutions Model CMC CMR 103 104 105 106 107 TABLE OF CONTENTS Section Page INTRODUCTION prua 1 1 Henny Penny Cold OPS lit iaia 1 1 y E o 1 1 Proper Cale ui hte mo pois dls 1 1 1 1 Ari 1 2 INSTALAN dridco 2 1 INTTOGUCHOT cia 2 1 IUe npe E m 2 1 Electrical M 2 2 LOCa ON MEE 2 3 Refrigerant Information miii aper alii 2 3 Dra 2 3 Compressor Size and Load iii 24 boot Print Drawing cisma era 2 4 Cut Out Dimensions for Dry Base or Table Installation eese 2 5 Flourescent Lighting and Bulb Replacement 2 6 Hot or Cold Top on a
11. del CMC CMR 103 104 105 106 107 defrost system computation dF digifrost Feature defrost start time based on total compressor running time rt real time defrost start frequency based on real time dI defrost interval defrost frequency in hours based on the dE dL selection of dS defrost endurance total maximum length of a defrost cycle expressed in minutes 1 99 range display lock temperature display is locked during a defrost cycle 0 31 range 6699 n no readout continues to display the actual tempera ture even during a defrost cycle ee 99 y yes readout is locked dr display read out select the type of visualization in case of temperature display lock during defrost see prameter dL C the temperature displayed at the start of a defrost is locked and does not change during this cycle dF during the defrost is displayed do defrost at power on selects whether or not the system dd goes through the defrost cycle at start up or after power failure 6699 59 y yes defrost delay at power delay of defrost cycle in minutes 0 99 range Error Code This is the only error code in these controls It indicates a tempera ture sensor failure such as a shorted sensor a sensor break or absence of sensor It can also indicate an under range in the system temperature 55 In case of an over range in t
12. he system temperature 99 shows first in the display followed by El 3 6 FLUORESCENT BULB 3 6 3 7 Y P Global Foodservice ENNY Solutions REPLACEMENT Model CMC CMR 103 104 105 106 107 UL Units 1 2 2 Pull the bulb of the sockets Remove the bulb guard caps Install new fluorescent bulb in reverse order CE Units 1 2 Remove the bulb cover Rotate the bulb Pull the lamp out of the sockets Install new fluorescent lamp in reverse order 1102 HENNY PENNY Model CMC CMR 103 104 105 106 107 Global Foodservice Solutions DIAGRAM FOR CMC MODEL 120 1 60 V Temp PTC SENSOR Contral 4 FRA 23 ZA by ral KC CONDENSING UNIT e FI 13 19 el Fr 53 MOTORS LIGHTS 1002 3 8 Y PENNY Model CMC CMR 103 104 105 106 107 Global Foodservice Solutions DIAGRAM FOR CMR MODEL 120 1 60 Y Temp PTC SENSOR Control 3 4 i vi D E pala S eno k Es w LI FAN MOTORS 3 9 1002 Model CMC CMR 103 104 105 106 107 Y P Global Foodservice ENNY LUMI RES cq 5 5 EVAPORATOR FAN DI JOAO VENTILATEUR Sr Fr D EVAPORATION TRNSFORMER TRANS FORMATEUR SONDE PTC COMPRESSOR RI COMPRESSEUR ed CONDENSING FAN VENTILATEUR DE CONDENSATION CMC CBC FANS NEONS 230V 50Hz 1 ph CE 1002 3
13. ic defrost cycles Fold down wood or plastic cutting board Sliding rear doors with double thermal mirrored glass Front glass lifts for easy cleaning 1 3 PROPER CARE As in any unit of food service equipment the Henny Penny cold top does require care and maintenance Requirements for the mainte nance and cleaning are contained in this manual and must become a regular part of the operation of the unit at all times 1 4 ASSISTANCE Should you require outside assistance just call your local indepen dent Henny Penny distributor in your area or call Henny Penny Corp 1 800 417 8405 toll free or 1 937 456 8405 503 1 1 Model CMC CMR 103 104 105 106 107 Y PENNY Global Foodservice 4 1 5 SAFETY The Henny Penny cold tops have many safety features incorporated However the only way to ensure a safe operation is to fully understand the proper installation operation and maintenance procedures The instructions in this manual have been prepared to aid you in learning the proper procedures Where information is of particular importance or safety related the words NOTICE CAUTION and WARNING are used Their usage is described below SAFETY ALERT SYMBOL is used with DANGER WARNING or CAUTION which indicates a personal injury type hazard NOTICE is used to highlight especially important information CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may resul
14. ilure could result Clean around the electronic controls with a soft damp cloth Reconnect the electrical power and unit is now ready for operation 303 3 4 Y PENNY Global Foodservice Solutions CLEANING 303 Continued Model CMC CMR 103 104 105 106 107 Every 3 Months 1 Remove all electrical power supplied to the unit by unplugging the power cord from the wall or by turning off the wall circuit breaker Remove all product from the unit Remove the riser and trays from the unit and clean with soap and water at a sink Clean interior surfaces with a soft cloth soap and water Do not use steel wool other abrasive cleaners or cleaners sanitizers containing chlorine bromine iodine or ammonia chemicals as these will deteriorate the stainless steel and glass material and shorten the life of the unit Do not use a water jet pressure sprayer to clean the unit or component failure could result Clean around light fixtures with a soft damp cloth Reconnect the electrical power and unit is now ready for operation SHOCK HAZARD If the power cord is damaged have a qualified service technician replace it to prevent electrical shock or property damage 3 4 YP Global Foodservice ENNY Solutions 3 5 PROGRAMMING Temperature Setpoint Other Parameters 3 5 Model CMC CMR 103 104 105 106 107 Press and hold for 4 seconds The light
15. ipped with an external circuit breaker which will disconnect all ungrounded unearthed conductors Referto the table below for electrical ratings Model No Volts Amps Phase Max Fuse Size CMC 103 120 7 1 1 15 103 230 4 5 1 15 104 120 7 4 1 15 104 230 4 5 1 15 105 120 8 6 1 15 105 230 6 0 1 15 106 120 8 6 1 15 106 230 6 0 1 15 107 120 9 5 1 15 107 230 7 7 1 15 303 Y P Global Foodservice ENNY Solutions 2 4 LOCATION 2 5 REFRIGERANT INFORMATION UL Specs CE Specs 2 6 DRAIN CONNECTION 303 Model CMC CMR 103 104 105 106 107 Place the cold tops in an area where product can be loaded and unloaded without interruption For proper operation level the unit by adjusting the bolts under the base and leave 3 feet 91 44 cm clearance behind the unit for ventilation and service For maximum efficiency units should be operated in an air condi tioned environment with maximum air temperature of 75 F 24 C and 55 relative humidity Wait at least 4 hours before plugging the unit into an electrical supply The gases and oils in the refrigeration system needs to settle before operating the compressor or damage to the compressor could result Refrigerant Type Amount of Refrig CMC 103 CMC 104 CMC 105 CMC 106 CMC 107 CMC 103 CMC 104 CMC 105 CMC 106 CMC 107 R22 R22 R22 R22 R22 R134A R
16. ne of the screws from step 1 Figure 2 3 Installation is now complete 2 7 Model CMC CMR 103 104 105 106 107 AA SECTION 3 OPERATION 3 1 INTRODUCTION This section provides explanations of all controls along with operating procedures and daily maintenance Read the Introduction Installation and Opeation Sections before operating the unit Wait at least 4 hours before plugging the unit into an electrical supply The gases and oils in the refrigeration system needs to settle before operating the compressor or damage to the compressor could result 3 2 OPERATING CONTROLS Referto figure 3 1 Fig Item Description Function No No 3 1 1 Power Switch Turns electrical power off and on to the unit located on the bottom of the control panel 3 1 2 Digital Display Shows the temperatures and the information in the Technical Mode 3 1 3 Used to increase setpoint values as well as programming values also automatic defrost cycles are programmed in the controls but to manually start a defrost cycle press and hold 1 for 3 seconds to start a manual defrost cycle DEF SET shows in display 3 1 4 Used to decrease setpoint values as well as programming values 3 1 5 Press to view the setpoint temperature or hold it for it for 4 h seconds to enter the program mode once in the Program Mode press to view other parameter setpoints Press E amy along with g and Ve change the parameters 3 1
17. pair or replacement of a part EXTENDED FRYPOT WARRANTY Henny Penny will replace any frypot that fails due to manufacturing or workmanship issues for a period of up to seven 7 years from date of manufacture This warranty shall not cover any frypot that fails due to any misuse or abuse such as heating of the frypot without shortening 0 TO 3 YEARS During this time any frypot that fails due to manufacturing or workmanship is sues will be replaced at no charge for parts labor or freight Henny Penny will either install a new frypot at no cost or provide a new or reconditioned replacement fryer at no cost 3 TO 7 YEARS During this time any frypot that fails due to manufacturing or workmanship is sues will be replaced at no charge for the frypot only Any freight charges and labor costs to install the new frypot as well as the cost of any other parts replaced such as insulation thermal sensors high limits fittings and hardware will be the responsibility of the owner Any claim must be represented to either Henny Penny or the distributor from whom the appliance was pur chased No allowance will be granted for repairs made by anyone else without Henny Penny s written consent If damage occurs during shipping notify the sender at once so that a claim may be filed THE ABOVE LIMITED WARRANTY SETS FORTH THE SOLE REMEDY AGAINST HENNY PENNY FOR ANY BREACH OF WARRANTY OR OTHER TERM BUYER AGREES THAT NO OTHER REMEDY INCLUDING CLAI
18. sal 303 2 5 Model CMC CMR 103 104 105 106 107 DAMA 2 10 FLOURESCENT LIGHTING No AND BULB REPLACEMENT Model of Lights Size CMR CMC 103 CMR CMC 104 36 in 914 m 48 in 1 22 CMR CMC 106 CMR CMC 107 36 in 914 36 in 914 m 48 in 1 22 m 1 36 in 914 m 1 1 UL Units 1 Pull the bulb out of the sockets 2 Remove the bulb guard caps 3 Install new fluorescent bulb in reverse order CE Units 1 Remove the bulb cover 2 Rotate the bulb 3 Pull the lamp out of the sockets 4 Install new fluorescent lamp in reverse order 2 6 403 Y PENNY Global Foodservice Solutions 2 11 COLD TOP ON A COLD BASE INSTALLATION INSTRUCTIONS 300000 TIT Figure 2 3 403 Model CMC CMR 103 104 105 106 107 Remove bolts securing the Cold Top to the skid and save bolts for later use Carefully set Cold Top on top of the Cold Base HEAVY OBJECT Take care when moving the fryer to prevent personal injury or damage to the refrigeration system The CMC 107s weigh over 700 Ibs 318 kg Line up the 2 front holes and secure the top to the base using the bolts from step 1 Figure 2 1 4 Locate mounting hole in right rear corner of the units and se cure the corner using one of the bolts from step 1 Figure 2 2 Pull the control panel out from unit and locate the mounting hole in the left rear corner Secure corner with o
19. ss Tyler Advantage Profile Mirrored RH 1 1 1 1 1 Continued on next page 1101 4 2 Y PENNY Model CMC CMR 103 104 105 106 107 Global Foodservice Solutions Use the chart below to identify the correct canopy glass assembly and the correct gas shock configuration Gas shock configuration is from left to right customer side Item Part Quantity Strength No No Description and Type of Wells of Gas Shocks 2 58607 001 HP Curved Profile 2 well Full Serve 2 200N 2 300N 2 58607 002 HP Curved Profile 3 well Full Serve 4 400N 2 58607 003 HP Curved Profile 4 well Full Serve 6 300N 2 58607 004 HP Curved Profile 5 well Full Serve 6 400N 2 58607 005 HP Curved Profile 6 well Full Serve 4 400N 2 58607 006 HP Curved Profile 7 well Full Serve 2 400N 2 500N 2 58607 016 Hussman Vision Profile 2 well Full Serve 2 400N 2 500N 2 58607 017 Hussman Vision Profile 3 well Full Serve 2 300N 4 400N 2 58607 018 Hussman Vision Profile 4 well Full Serve 6 300N 2 400N 2 58607 019 Hussman Vision Profile 5 well Full Serve 4 400N 4 500N 2 58607 020 Hussman Vision Profile 6 well Full Serve 2 per unit 4 300N 2 400N 2 58607 021 Hussman Vision Profile 7 well Full Serve 2 per unit 4 400N 2 500N 2 58607 031 Flat Profile 2 well Full Serve 4 300N 2 58607 032 Flat Profile 3 well Full Serve 4 500N 2 58607 033 Flat Profile 4 well Full Serve 2 300N 4 400N 2 58607 034 Flat Profile
20. t in property damage CAUTION used with the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury 1 2 303 Y PENNY Global Foodservice 4 Model CMC CMR 103 104 105 106 107 SECTION 2 INSTALLATION This section provides the installation for Henny Penny cold tops 2 1 INTRODUCTION 2 2 UNPACKING 303 Installation of this unit should be performed only by a qualified service technician SHOCK HAZARD Do not puncture the unit with any objects such as drills or screws or component damage or electrical shock could result The Henny Penny Cold Top has been tested inspected and expertly packed to insure arrival at its destination in the best possible condition The grids side glass and sliding thermal doors are packed separately inside the unit The cabinet rests on a wooden skid and is then packed inside a heavy cardboard carton with sufficient padding to withstand normal shipping treatment To avoid damage to the components do not lay the unit on its side If the unit has been on its side the unit must be in an upright position for at least 4 hours before power is applied to the unit Check all components for signs of being loose or dam aged and make sure the system has refrigerant When moving the cold top
21. t of this section for other rights and limitations Recommended replacement parts stocked by your distributor are indicated with V in the parts lists Please use care when ordering recommended parts because all voltages and variations are marked Distributors should order parts based upon common voltages and equipment sold in their territory 206 HENKII PENNY Model CMC CMR 103 104 105 106 107 Global Foodservice Solutions 2 1 Item Part Quantity No No Description 103 104 105 106 107 1 56242 001 Side Glass Flat Clear 2 2 2 2 2 1 56242 002 Side Glass Flat Mirrored LH 1 1 1 1 1 1 56242 003 Side Glass Flat Mirrored RH 1 1 1 1 1 1 56050 001 Side Glass HP Profile Clear 2 2 2 2 2 1 56050 002 Side Glass HP Profile Mirrored LH 1 1 1 1 1 1 56050 003 Side Glass HP Profile Mirrored RH 1 1 1 1 1 1 56050 006 Side Glass HP Profile Mirrored Antique White LH 1 1 1 1 1 1 56050 007 Side Glass HP Profile Mirrored Antique White RH 1 1 1 1 1 1 56050 008 Side Glass HP Profile Mirrored Shadow Black LH 1 1 1 1 1 1 56050 009 Side Glass HP Profile Mirrored Shadow Black RH 1 1 1 1 1 1 56241 001 Side Glass Hussman Vision Profile Clear 2 2 2 2 2 1 56241 002 Side Glass Hussman Vision Profile Mirrored LH 1 1 1 1 1 1 56241 003 Side Glass Hussman Vision Profile Mirrored RH 1 1 1 1 1 1 56239 001 Side Glass Tyler Advantage Profile Clear 2 2 2 2 2 1 56239 002 Side Glass Tyler Advantage Profile Mirrored LH 1 1 1 1 1 1 56239 003 Side Gla
22. uicktronic Ballast Fluorescent Light F25T8 835 36 CMC CMR 103 105 106 107 Fluorescent Light F32T8 SP35 48 CMC CMR 104 107 Fluorescent Light F17T8 SP35 24 CMC CMR 105 White Socket for Neon Light Magnetic Contactor 120V 20A 2 pole Power Switch Fan Light 125V Plastic Protector Fluorescent Light 48 CMC CMR 104 107 Plastic Protector Fluorescent Light 36 CMC CMR 103 105 106 107 Plastic Protector Fluorescent Light 24 CMC CMR 105 Cutting Board 3 Pan Cutting Board 4 Pan Cutting Board 5 Pan Cutting Board RH 6 Kit Gasket amp Seal CMC CMR 10X Panel Rear Access 3 well Panel Rear Access 3 well CE Panel Rear Access 4 well Panel Rear Access 4 well CE Panel Rear Access 5 well Panel Rear Access 5 well CE Panel Rear Access 7 w o Cord Cap Protective End Fluorescent Light Quantity Model CMC CMR 103 104 105 106 107 103 104 105 106 107 ee are WN Ra a e a a Nk I m 1 N 1 1 e a 1 AA a BR I 1 pi 1 1 NR ka a A Da I fis 1 1 en a Li 206
Download Pdf Manuals
Related Search