Hayter Mowers 3401 Lawn Mower User Manual
Contents
1. Engine vibrates excessively POSSIBLE FAULT Mounting bolts loose Cutterblade bolt loose Cutterblade out of balance Bent crankshaft REMEDY Tighten bolts Tighten bolt Balance cutterblade Consult your dealer Uneven cut Undulating ground conditions Cutterblade worn Cutterblade out of balance Wheels roller damaged Change direction of travel Sharpen the cutterblade Balance the cutterblade Inspect and replace as necessary Discharge chute blocks Grass is wet Cut height too low Grassbag full Airflow through the grassbag is restricted Engine speed too slow Mow dry grass Increase cut height Empty grassbag Clean the grassbag Set throttle to fast position Mower is hard to push Cut height too low Wheels roller damaged Increase cut height Inspect and replace as necessary Mower will not self propel Clutch out of adjustment Adjust clutch cable Autodrive Only Drive belt damaged Replace drive belt Poor grass collection Airflow through the Clean the grassbag grassbag is restricted Discharge chute blocked Remove blockage Wet grass Mow in dryer conditions Grassbag full Empty grassbag 1 30 Engine speed too slow Set throttle to fast position OF CONFORMITY EC DECLARATION OF CONFORMITY HAYTER LIMITED Spellbrook Bishop s Stortford Herts CM23 4BU ENGLAND declare that the lawnmowers Models Harrier 56 Harrier 56 Machine Type No CODE 340A CO2. exhaust periodically and replace if worn or leaking Never crank the engine with the spark plug removed Never start the engine with the air cleaner or air cleaner cover removed Never store the mower with petrol in the tank within an enclosed area where fumes may reach an open flame or spark 1 10 SAFETY PRECAUTIONS Allow the engine to cool before storing in any enclosure To reduce the fire hazard keep the engine and the surrounding deck area free of grass leaves or excessive grease Check the rear deflector and grassbag frequently for wear or deterioration Replace worn or damaged parts for safety If the fuel tank has to be drained this should be done outdoors and when the engine is cool Wear strong work gloves when removing and reassembling the cut terblade Always replace worn or faulty parts with genuine Hayter parts ymbols Safety Alert Be aware to the Danger of severing toes or fin Danger of being hit by thrown possibility of injury gers in cutting mechanism objects Carefully read the Owners Stop engine and remove spark Keep bystanders at a safe dis Handbook before using the plug lead before working on tance from the mower machine the mower g bad LO J Engine Stop Height of Cut Adjustment Throttle Control Symbol Symbol Symbols TO cb Lt z ASSEMBLING THE MOWER Remove the mower from the packaging and check tha
3. fasteners 300144 2 2 119 Decal Grass Blade 410064 1 1 1 34 LIST PARTS 340S 341S1 1 35 CUSTOMER INFORMATION 7NOTES Engine Type 111682 0165 El 340A Engine Briggs amp Stratton INTEK 55 Engine Type 111687 0166 El 341A Engine Briggs amp Stratton INTEK 55 Date of Sale Your Local Dealer Notes 1 36
4. mower across areas other than grass Never operate the mower unless the guards are securely in position and in good condition Do not change the engine governor settings or overspeed the engine Disengage the rear roller drive clutch before starting the engine Start the engine carefully with feet well away from the cutterblade SAFETY PRECAUTIONS VAL nea Upel a Do not tilt the mower when starting the engine Do not put hands or feet near or under rotating parts Never pick up or carry the mower while the engine is running Never lift the rear deflector while the engine is running Never touch the exhaust exhaust guard or cooling fins when the engine is hot Stop the engine and disconnect the spark plug lead Before clearing blockages or unclogging the discharge chute Before cleaning checking or working on the mower After striking a foreign object Inspect the mower for damage and ensure necessary repairs are made before re starting If the mower starts to vibrate abnormally check immediately Stop the engine Whenever you leave the mower Before refuelling vm emp E ZS Te CA GWE oy a Keep all nuts bolts and screws tight to ensure that the equipment is in safe operating condition Frequently check fuel lines and fittings for cracks or leaks and replace if necessary Never check for a spark when the spark plug is removed Use approved tester Inspect the
5. mower on a level surface unscrew and remove the oil filler dipstick Wipe oil from it with a clean cloth Screw the oil filler dipstick back in place then unscrew and remove it to check the oil level The oil level is correct when it is at the full mark on the dipstick DO NOT OVERFILL Always use clean fresh unleaded petrol Purchase fuel in quantities that can be used within 30 days Never mix oil with petrol For added engine protection Briggs amp Stratton recommend the use of their fuel additive which is available from an authorised Briggs amp Stratton ser vice dealer Fill to base of neck to allow for fuel expansion Do not overfill the fuel tank OPERATING THE MOWER 5 J Operate all control levers several times and ensure that the cables move freely Check that the engine stop and ground drive clutch levers return freely to their rest position when released Whilst operating the engine throttle mechanism slight resistance should be felt when moving the lever to the choke position Move the throttle control lever to the choke position before starting a cold engine Move the throttle control lever to the fast position before starting a warm engine Stand behind the mower and hold the handlebar together with the engine stop lever with your left hand With your right hand hold the engine start grip and pull slowly until resistance is fe
6. via a friction disc to help pre vent damage occurring to the engine crankshaft and cutting mecha nism when a hidden obstruction or overload is encountered Always stop the engine when a hidden obstruction or excessive vibra tion is encountered Disconnect the spark plug lead and examine the cutting mechanism ALWAYS replace a damaged cutterblade refer to Maintenance When moving the mower across non grassed areas stop the engine and set the mower to the maximum height of cut to protect the cutting mechanism LAWN CARE CALENDAR To be used as a guide only January There is very little work to do this month apart from brushing away leaves Keep off the grass if frozen or waterlogged February Rake the grass thoroughly Spike the lawn to aerate and stimulate soil organisms and root growth and apply lawn sand if necessary March The yearly lawn work programme really starts this month As soon as the ground conditions are suitable the first cut can be made The first cut should merely top the grass as close cutting at this stage could result in severe yellowing or browning Two cuts are generally suffi cient this month April Mow often enough to stop grass growing away Dig out patches of coarse grass or resistant weed Re seed bare patches i May Keep mowing increasing the frequency as required Treat with selec tive weed killers or combined weed feed preparations i
7. 2 2 77 Nut Plain M6 09437 3 3 78 Insert Front Fin 340190 1 1 79 Rope Guide 305093 1 1 80 Lever Clutch 306094W 1 1 81 Nut M6 Nyloc Insert 09438 1 1 82 Washer Spring M6 09474 3 3 1 33 PARTS LIST QTY ITEM NO DESCRIPTION PART NO 340A 341A ITEM NOTE 83 Decal Caution 219189 1 1 84 Handwheel 226013 2 2 85 Grassbag Fabric 340071 1 1 86 Cable Clutch 341034 1 1 87 Tube Plug 300160 2 2 88 Roller Bearing Housing 219102 Se 89 Cover Grassbag 340072 1 1 90 Grassbag Assembly 340070 1 1 Includes4 38 85 89 93 94 amp 95 91 Cable Tie 3966 3 3 92 Brush Seal 340082 1 1 93 Handle Grassbag 340073 1 1 94 Frame Grassbag Assembly 340075 1 1 95 U Tube 340078 Ty lt i 96 Decal Hayter amp Royal Warrant 410087 1 1 97 Oilite Bush Roller 340129 2 32 98 Roller Assembly 340139 Se 99 Spacer Nylon 340149 2 2 100 Wheel Roller Free 340150 GE 101 Bush 340154 Dee 52 102 Locknut 340163 1 1 103 Roller Shaft 340162 1 1 104 Shroud Freewheel 340168 1 1 105 Rope Stop MU42189 1 1 106 Lever Engine 340179 1 1 107 Pin Pivot 340182 2 2 108 Handlebar Upper 341029W 1 1 109 Decal Engine Stop 331046 1 1 110 Charger 226006 0 1 111 Decal Engine 340224 1 1 112 Throttle Control amp Cable 341028 1 1 113 Battery 12V 220015 0 1 114 Clip Battery 220014 0 1 115 Rivet Avdel 09318 0 2 116 Bracket Battery 220013 0 1 117 Key Ignition 6426 0 1 118 Drive
8. 7 1 28 1 29 1 30 1 31 1 32 1 34 1 35 1 36 CONTENTS Mower Maintenance Engine Throttle Cable Adjustment Carburettor Adjustments Oil Service Air Cleaner Service Spark Plug Service Keeping Engine Clean Grassbag Deck Housing Securing Nuts and Bolts Clutch Cable Adjustment Lubrication Cutterblade Removal Cutterblade Assembly Cutterblade Sharpening Storage Battery Charging Trouble Shooting Declaration of Conformity Parts List Parts list Diagram Customer Info Notes INTRODUCTION Thank you for purchasing a Hayter mower The following pages are designed to help you gain safe and efficient service from your mower IMPORTANT This Owners Handbook should be regarded as part of the mower as it gives essential information regarding mower safety operation maintenance and specifications Read and understand this handbook prior to operating your mower for the first time Make sure you are familiar with all the controls and points of regular maintenance If you have any doubts consult your local Hayter authorised dealer who will be pleased to give you assistance IMPORTANT This mower is designed solely for use in a domestic grass cutting environment Use in any other way is considered as contrary to the intended use Compliance with and strict adherence to the conditions of operation service and repair as specified in this handbook also constitute essential elements of the intend
9. DE 341A Category Auto Drive Auto Drive Electric Start Type Pedestrian Rotary Pedestrian Rotary Engine Manufacturer Briggs amp Stratton Briggs amp Stratton Speed of rotation 2800 rpm 2900 rpm Width of cutting device 560mm 560mm Speed of rotation of the cutting device 2800 rpm 2900 rpm Complies with the provisions of Directive 98 37 EC Essential Health amp Safety Requirements Relating to the Design amp Construction of Machinery and Safety Components as amended and the regulations transposed into national law Also Directive 89 336 EEC Electromagnetic Compatibility as amended and the regulations transposed into national law Also Directive 2000 14 EC Noise emission in the environment by equipment for use outdoors and the regula tions transposed into national law procedure applied for the conformity assessment ANNEX VI procedure 1 Notified Body Sound Research Laboratories Ltd Holbrook House Little Waldingfield Sudbury Suffolk ENGLAND Notified body identification No 1088 Measured sound power level 92 dB A 92 dB A Guaranteed sound power level 100 dB A 100 dB A Standards Used EN292 EN836 and ENISO14982 Authorised Signatory Date 03 10 01 Jk a bat Declaration done and Technical Documentation kept at es HAYTER LIMITED M A Wright Spellbrook Bishop s Stortford Technical Director Herts CM23 4BU ENGLAND Signed VIBRATION INFORMATION Lawnmower vibration information RMS acceleration m
10. Harrier 56 CODES 340A 341A Auto Drive Electric Start Variable Speed OWNER S HANDBOOK English Version FROM SERIAL NO 340A001001 3414001001 HANDBOOK 340228 REV 1 ISSUE 09 9 03 MAIN FEATURES SPECIFICATIONS Main Features 5 1 Spark Plug lead 2 Engine Cover 3 Air Cleaner 4 Fuel Cap 5 Oil Filler Cap amp Dip Stick 6 Handle Securing Knob 7 Engine Start Grip 8 Engine Stop Lever 9 Handlebar 10 Ground Drive Clutch Lever 11 Key 341A Only 12 Throttle Control 13 Grassbag Assembly 14 Rear Deflector 15 Serial No Label 16 Height of Cut Lever 17 Battery 341A Only 18 Muffler Guard 18 Specifications Code 340A Engine Briggs amp Stratton INTEK 55 Engine type 111682 0165 E1 Engine Cutterbar speed 2800 rpm Fuel type Unleaded petrol Fuel capacity 1 5 litres Oil type SAE 30 engine oil Oil sump capacity 0 6 litres Cutting width 560mm Cutting height 10 60mm Overall dimensions 1 511 x 591 x 1 156mm Dry Weight 50 5 Kg J 3D340A1 341A Briggs amp Stratton INTEK 55 111687 0166 E1 2900 rpm Unleaded petrol 1 5 litres SAE 30 engine oil 0 6 litres 560mm 10 60mm 1 511 x 591 x 1 156mm 53 5 Kg HAYTER HAYTER Ml MAKERS OF THE FINEST MOWERS EE MAKERS OF THE FINEST MOWERS 1ST Year 12 months 1ST Year 12 months Owner s Name We certify that this service has been carried out by an Authorised Hayter Serial Numb
11. To make a wide turn steer the mower with the handlebar in the direc tion required To make a tight turn release the ground drive clutch lever apply down ward pressure on the handlebar to raise the front wheels just above ground level and steer in the required direction To prevent accidents do not raise the front of the mower exces sively when making a turn Never raise the rear of the mower when the engine is running Release the ground drive clutch lever reduce the throttle setting and release the engine stop lever Emergency stop Release both ground drive clutch lever and engine stop lever together If the engine fails to stop move the throttle lever to the slow posi tion and disconnect the spark plug lead OPERATING THE To prevent engine damage do not use the mower on slopes greater than 20 degrees gt J To adjust the height of cut Grip the lever and pull sideways to dis engage it from the locking notch then push forwards to lower or pull backwards to raise the height of cut Finally release the lever at the required position and ensure it locks firmly into one of the nine setting notches Always select a height of cut to suit operating conditions Aim to pre vent engine overloading and blockages by avoiding low cuts in long grass conditions Be prepared to make two cuts when the grass is long 5 J To prevent accidents thoroughly inspect the area a
12. bar Set the plastic adjuster A as necessary If further adjustment is required unscrew the lock nuts 1 and screw the adjuster 2 in or out as necessary Tighten the locknuts 1 when correctly adjusted 1 24 MOWER MAINTENANCE Lubricate the wheels pivot points and linkages with engine oil every 25 operating hours Apply a good quality medium grease to the inner control cables at the point of entry and exit from their outer casing Drain the fuel by running the engine until the fuel tank is empty and the engine stops Remove the spark plug lead and allow the engine to cool Turn the mower on its left hand side and ensure that the air clean er side of the engine is uppermost Firmly grip the end of the cutterblade with the gloved hand and remove the bolt spring washer and distance piece securing the cutterblade with a 9 16 A F spanner To prevent accidents never work on the cutterblade unless the spark plug lead has been removed The cutterblade has sharp edges ALWAYS wear strong gloves to protect your hands when working on the cutterblade DO NOT rotate tools towards the cut ting edges to avoid the risk of injury should the tool slip ALWAYS use genuine Hayter replacement parts The condition of the cutterblade and its mounting arrangement should be checked regularly for signs of wear or damage Ensure that the cut terblade is not bent or cracked A damaged cutterblade that is ou
13. battery Disconnect the battery leads 1 27 MOWER MAINTENANCE ei ny 1 28 We PREVENT ACCIDENTS ALWAYS charge the battery in a well ventilated area NEVER charge the battery near naked flames or direct heat ALWAYS switch off the mains electricity supply before discon necting the charger from the battery ALWAYS use the battery charger supplied with the mower Battery charging should not be necessary during normal use The engine operation will automatically charge the battery If the mower is stored for a long period recharging the battery may be necessary to per mit electric starting Charge the battery only when necessary To recharge the battery Disconnect the battery lead from the mower lead and then connect the battery lead to the charger Connect the charger plug to the mains electricity supply and switch on to charge the battery for a 14 hour period Switch off the mains electricity supply and disconnect the charger plug Disconnect the battery lead from the charger and then connect the battery lead to the mower lead IMPORTANT PREVENT DAMAGE NEVER connect the bat tery charger to the engine lead as this will cause the charger to be permanently damaged Chargers damaged in this manner will not be replaced under warranty CAUTION PREVENT ENVIRONMENTAL DAMAGE The battery has a separate collection mark This indicates that the used battery must be taken to an author
14. crew Washer Hd Taptite M6 x 12 09546 De 2 37 Nut M8 Nylon Insert T Type 09441 2 2 38 Rivet 09320 4 4 39 Bolt Coach M6 x 20 09668 2 2 40 Bolt Hex Hd M6 x 30 09547 1 1 41 Screw 6mm x 20 09687 25 2 42 Bolt Coach M8 x 45 226024 2 2 1 32 PARTS LIST QTY ITEM NO DESCRIPTION PART NO 340A 341A ITEM NOTE 43 Distance Piece 4014 1 1 44 Washer Nylon 19mm 09688 2 2 45 Mainframe Assembly 340205V 1 1 46 Throwplate 340011 1 1 47 Idler Sprocket Sleeve Assembly 219095 1 1 48 Plate Ratchet 340102 1 1 49 Cable Engine Brake 341031 1 1 50 Cap Nut 234051 2 2 51 Handlebar Lower LH 340103 1 1 52 Jockey Lever 219023 1 1 53 Sprocket 10 Teeth 219106 1 1 54 Plate Securing 219028 1 1 55 Woodruff Key 5321 1 1 56 Rod Connecting 340014 1 1 57 Axle Front Assembly 340020 1 1 58 Bearing Moulding 219036 2 2 59 Plate Securing 219037 2 2 60 Pulley Jockey 219156 1 1 61 Sprocket 17 Teeth 219051 1 1 62 Handlebar Lower RH 340104 1 1 63 Engine Compliance A P T O 346040 1 0 Engine Compliance A P T O 341037 0 1 64 Spacer 219053 1 1 65 Electric Start 341038 0 1 66 Cover Transmission 219055 1 1 67 Coupling 340109 1 1 68 Bearing Housing Moulding 219060 1 1 69 Pulley Assembly 340105 1 1 70 Bracket Belt Guide 219064 1 1 71 Chain 219054 1 1 72 Cover Transmission 340050 1 1 73 Underguard 340051 1 1 74 Deflector Rear 340022 1 1 75 Rod Pivot 340024 1 1 76 Spring Deflector 340052
15. e a neat striped effect is for the lawn being cut in A parallel stripes alternate stripes being mown in opposite directions A much more important routine is to cut at right angles to the line of the previous mowing If the work has been carried in a north south line then the next cutting should be in an east west direction The cross cutting keeps down the coarse weed grasses To prevent grass damage do not remove more than one third of the grass height in one cut MAINTENANCE SCHEDULE Follow the hourly or calendar intervals whichever occurs first More frequent service will be required if working for prolonged periods under dusty dry conditions or when airborne debris is present or after extensive operation cutting tall dry grass First 5Hrs After the very first five hours change the engine oil Daily Check the oil level Remove grass debris from around the engine exhaust exhaust guard and air ways in the top cowl and underside of the deck housing Remove grass debris from the grassbag and check for signs of damage Check the condition of guards and safety devices Check condition of cutterblade 25Hrs or Every Season Change the engine oil if continuously operating under heavy load or high ambient temperature Service the air cleaner Lubricate wheels pivot points and linkages and grease the inner con trol cables at point of entry a
16. e provided through their authorised network To qualify for the full benefit of the warranty the warranty registration card must be returned within 14 days of purchase Subject to the conditions and exclusions noted in this limited warranty we shall at our option repair or replace any warranted part during the applicable period If you are in doubt or experience any difficulty please consult a Hayter Authorised Service Dealer for clarification To qualify for the extended warranty second and third year of the three year limited warranty the machine must have annual services carried out by an Authorised Hayter Service Dealer These chargeable services should be carried out within 12 and 24 months of the date of purchase Excluded from the extended warranty period are those items which are subject to normal wear and tear e g tyres wheels cutterblades belts cables grassbags sweeper brushes batteries and other consumable wearing parts All consumer machines which are fitted with a genuine Hayter friction disc as original equipment before use are covered by a Lifetime Warranty against the engine crankshaft bending Note friction washers blade brake clutch B B C units and other such devices are not applicable Only machines fitted with a genuine Hayter friction disc which are used in accordance with the recommended operating and maintenance procedures are covered This warranty does not apply to any unit that has been tampered with alt
17. easured in 3 axes at operators contact position on the handlebars CODE 340A 10 6 ms CODE 341A 10 6 ms 1 31 PARTS LIST QTY ITEM NO DESCRIPTION PART NO 340A 3414 ITEM NOTE 1 Belt 340049 1 1 2 Circlip 5 8 1428 1 1 3 Woodruff Key 1662 1 1 4 Washer 3 16 09257 4 4 5 Spring 5421 2s 2 6 Cutterblade 340015 1 1 7 Washer Plain 5 8 09286 1 1 8 Spring Clip 5 16 04020 1 1 9 Bush 1 2 x 5 8 x 3 4 4452 1 1 10 Screw M6 x 12 Csk Pozi Taptite 09545 4 4 11 Wheel 5218 2 2 12 Hub Cap 219143 2 2 13 Nut M6 Nylon Insert T Type 09544 1 1 14 Screw M6 x 20 Hex Hd Taptite 09575 2 2 15 Washer 1 2 Plain 02575 1 1 16 Friction Disc 219203W 1 1 17 Washer Plain 5 16 09266 1 1 18 Washer Plain 1 2 09280 27 2 19 Washer Plain M6 09472 ZS 20 Clamp Handlebar 340028 2 2 21 Circlip 3 4 02708 2 32 22 Circlip 1 2 03096 1 1 23 Pin Roll 3 16 x 3 4 03997 4 4 24 Screw Taptite 3 8 UNC x 1 1 4 09349 30 3 25 Setscrew Hex Hd 3 8 UNF x 1 1 4 09116 1 1 26 Nut Nylon Insert 1 2 UNF 4486 Qe 2 27 Washer Starloc 5 16 0201086 2h 2 28 Knob Height Adjuster 330053 1 1 29 Washer Spring 3 8 09273 1 1 30 Pulley 219111 1 1 31 Spring 1246 1 1 32 Screw Pozi Pan 09780 1 1 33 Screw Hex Hd Taptite M6 x 16 09365 23 23 34 Frame Rear Roller 340044 1 1 35 Bolt Coach M8 x 40 09379 2 2 36 S
18. ed use This mower should be operated serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety procedures The safety precautions listed in this handbook and all other generally recognised regulations on safety must be observed at all times Any arbitrary modifications carried out to this machine may relieve Hayter Limited of liability for any resulting damage or injury Hayter mowers are robustly constructed and designed for efficient economical performance under normal mowing conditions Correct operation and maintenance will ensure a long and satisfactory service life Prior to despatch from our factory every effort is made to ensure that your mower is delivered in perfect condition Throughout this handbook all references to left and right are as viewed from behind the han dlebar in the direction of forward travel This handbook is based on information available at the time of publication HAYTER LIMITED reserve the right to amend product specifications without prior notification WARRANTY LIMITED WARRANTY Hayter Limited warrants to the original user purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of three years from the date of purchase The manufacturer of major proprietry components ie engines gearbox transaxle where applicable furnish their own warranty and services ar
19. er Service Dealer Date Date Note for dealer Please retain this voucher for your records GE gt HAYTER HAYTER EE MAKERS OF THE FINEST MOWERS H EE MAKERS OF THE FINEST MOWERS 2nd Year 24 months 2nd Year 24 months Owner s Name We certify that this service has been carried out by an Authorised Hayter Serial Number Service Dealer Date Date Note for dealer Please retain this voucher for your records 18 1 14 118 1 2 15 1 6 1 7 1 11 1 11 1 11 1 12 1 12 1 12 1 12 1 13 1 13 1 13 1 13 1 13 1 19 1 14 1 14 1 14 1 14 1 15 1 15 1 15 1 15 1 16 1 16 1 16 1 16 1 17 1 17 1 17 1 17 1 19 1 19 1 18 Main Features Specifications Contents Introduction Warranty Safety Precautions Safety Symbols Decal Symbols Assembling the Mower Delivery Checklist Handlebar Grassbag Attachment Before Starting the Engine Prevent Engine Damage Oil Type Check Oil Level Fuel Type Operating The Mower Controls Starting Step 1 Step 2 Step 3 Electric Start Forward Travel Turning Stopping Slopes Height of Cut Before Mowing Grassbag Without Grass Collection Heavy Growth Friction Disc Non Grassed Areas Lawn Care Calendar Guide Only Lawn Stripes Maintenance Schedule 1 21 1 28 1 21 1 21 1 21 1 21 1 22 1 22 1 23 1 23 1 24 1 24 1 24 1 25 1 25 1 26 1 26 1 2
20. ered misused abused or used for hire and will become invalid if non genuine Hayter parts are fitted This warranty does not cover minor mechanical adjustments unless they are due to defective material or workmanship Consult the Owner s Handbook or a Hayter Authorised Service Dealer for assistance when making these adjustments A warranty period of 90 days applies to machines used for commercial purposes To make a warranty claim return the unit to a Hayter authorised dealer along with proof of purchase stating the machine serial number and date of purchase The service receipt s or this Owners Handbook with the Ist 2nd year service boxes fully completed must be produced as proof of entitlement to the extended warranty period Subject to the conditions and exclusions in this limited warranty the authorised dealer will at our option repair or replace any warranted part within the duration of the warranty period This limited warranty gives you specific legal rights and is in addition to any statutory rights to which you may be entitled and your statutory rights are not affected by this warranty If you need additional information concerning this written warranty or assistance in obtaining services please write to HAYTER LIMITED Service Department Spellbrook Bishop s Stortford Hertfordshire CM23 4BU Issue 05 09 03 UK ONLY Details of your local Hayter authorised dealer are contained in Yellow Pages and the Hayter website www ha
21. f you did not feed the lawn in April June Summer mowing should now be under way It should be necessary to mow the lawn twice a week Raking before mowing is important this month as the combined action keeps runners of clover under control Water the grass if necessary and remember to soak thoroughly bi July Treat the grass with the second application of fertiliser or weed killer fertiliser Water when necessary and rake occasionally As a gen eral rule the grass clippings should be removed each time you mow If weather conditions are dry and hot and the grass is weed free leave the clippings on the lawn to help maintain ground moisture 5 1 18 CAWN CARE CALENDAR August Keep mowing regularly and watering as necessary Fill any cracks caused by drought with a mixture of sharp sand and soil In dry weath er conditions leave the grass longer to help retain ground moisture September Raise the height of cut to allow the grass to thicken and protect the roots from the winter frost and snow October Rake out the thatch from the turf and spike the lawn to assist in drainage Brush in peat and sharp sand No vember Use a stiff broom to disperse worm casts before mowing Keep turf free from leaves December Apart from brushing away leaves December is a slack end of a busy year Keep off the lawn if it is very wet or frozen Lawn Stripes The way to achiev
22. gainst the mower Take care to ensure that the control cables do not become snagged at the pivot point and depress the engine stop lever to prevent it being dam aged through contact with the engine spark plug Engines stored in excess of 30 days need to be protected with Briggs amp Stratton fuel additive or drained of fuel to prevent gum from forming in the fuel system or on essential carburettor parts To ensure your mower is maintained in good working order it is important that the following procedure is adopted Refer to the Maintenance section as necessary Drain fuel from the engine by operating the engine until it stops Disconnect the spark plug lead Change the engine oil Remove the engine spark plug and pour 15ml of engine oil into the engine cylinder and replace the spark plug Do not exceed the stated volume of oil as engine damage may occur on re starting Do not replace the spark plug lead Slowly pull the engine start grip once to crank the engine This will distribute the oil and help prevent engine corrosion Clean grass and debris from the engine cylinder cylinder head cooling fins under top cowl and around and behind exhaust exhaust guard Clean all other areas of the mower and ensure that the grassbag is clean Lubricate the mower Treat metal parts with a water repellent anti corrosion product Cover the mower with a protective sheet and store it in a dry ventilat ed area Electric Start Only Charge the
23. hereafter according to the Maintenance Schedule 1 Drain fuel by running the engine until the fuel tank is empty 2 Remove the spark plug lead 3 Allow the engine to cool 4 Drain the oil while the engine is warm not hot 5 Tip the mower over on to its left hand side thus ensuring that the air cleaner is kept uppermost to prevent engine damage 6 Remove the oil filler dipstick and drain the oil into a suitable container 7 Refill with new oil of the recommended SAE viscosity grade Refer to Before Starting the Mower Air Cleaner Service To service the air cleaner loosen the two screws 1 and remove cover 2 Carefully remove pre cleaner 3 and cartridge 4 wash in a solu tion of liquid detergent and water Allow to air dry thoroughly before fitting If very dirty replace Do not use petroleum solvents Do not use pressurised air Do not oil the cartridge After servicing install the pre cleaner and cartridge in the assembly base 5 Replace the cover and securely tighten the screw to the base MOWER MAINTENANCE e D Use only Briggs amp Stratton spark tester 1 to check for a spark as shown in the diagram Replace the spark plug every 100 hours or every season whichever occurs first A spark plug wrench is available from any authorised Briggs amp Stratton service dealer Check the spark plug gap with a feeler gauge and set at 0 76mm Remove a
24. ised disposal site It must not be disposed of with general waste PROBLEM TROUBLE SHOOTING POSSIBLE FAULT REMEDY Engine will not turn over Engine stop lever released Incorrect oil level Obstruction under deck Battery discharged 341 AOnly Operate engine stop lever Check oil level Remove obstruction Charge battery Engine smokes Excess oil level Air cleaner cartridge oil soaked or blocked Check oil level Service air cleaner Engine runs then stops Fuel starvation Fuel cap vent blocked Fill fuel tank Clean fuel cap vent Engine will not start Engine under load Fuel starvation Engine cold Incorrect contaminated fuel Spark plug lead disconnected Throttle setting incorrect Engine brake not released Faulty spark plug Battery discharged 341A Only Wiring fault Raise height of cut Fill fuel tank Set throttle to choke position Drain fuel tank and fill with correct fuel Connect spark plug lead Set throttle to fast position Operate engine brake lever Clean and adjust gap or replace Charge battery Check wiring Engine runs rough Spark plug lead becoming disconnected in use Faulty spark plug Air cleaner blocked Incorrect contaminated fuel Connect spark plug lead Clean and adjust gap or replace Service air cleaner Drain tank and fill with correct fuel 1 29 TROUBLE SHOOTING PROBLEM
25. ll grass and debris from the engine including the exhaust exhaust guard the air ways in the top cowl and the surround ing deck areas on a daily basis after use Never spray the engine with water during cleaning Water can contaminate the fuel Always clean with a brush or compressed air Grass and debris may clog the engine s air cooling system especially after prolonged operation while cutting tall dry grass The internal cool ing fins and surfaces may require cleaning to prevent overheating and engine damage We recommended that this service be carried out by an authorised Briggs and Stratton dealer Gra Remove grass debris from the grassbag immediately after use and check its condition for signs of damage To prevent accidents replace a damaged grassbag immediately MOWER MAINTENANCE Remove grass debris from the top and underside of the deck housing immediately after use Fertilisers and top dressings are particularly corrosive Thoroughly clean the mower deck immediately after use on treat ed grass and store well away from corrosive materials Regularly check that all securing nuts and bolts are tight Replace missing or damaged items immediately Auto Drive Models Only Check the clutch cable operation every 25 operating hours and adjust if necessary The clutch cable is adjusted correctly when the belt drive just engages with the clutch lever positioned 32 38mm from the han dle
26. lt then pull rapidly to crank the engine carefully return the start grip to the storage position when the engine starts If the engine does not start after 5 attempts refer to Trouble Shooting The engine stop lever must be held firmly against the handlebar to start and keep the engine running If the engine stop lever is released the engine will stop Allow the engine to warm up and move the throttle lever to the fast position after starting a cold engine To prevent damage never pull the engine start grip when the engine is running Electric start Only Stand behind the mower and hold the handlebar together with the engine stop lever Turn the ignition key in a clockwise direction and hold in position to crank the engine When the engine starts release the key and move the throttle to the fast position after starting a cold engine Note Cranking the engine for more than 15 seconds in any one minute can damage the starter motor If necessary the engine can be started manually without using the igni tion switch To prevent engine damage do not operate the ignition key when the engine is running Hold the handlebar and operate the ground drive clutch lever to power the mower in a forward direction When the ground drive clutch lever is disengaged the mower may be pushed This feature is useful when mowing in confined areas If the engine stop lever is released the engine will stop
27. nd exit from their outer casing Check the clutch cable adjustment Sharpen the cutterblade 50Hrs or Every Season Change the engine oil 100Hrs or Every Season Clean the engine cooling system Clean more often under dusty condi o 1 20 tions or when airborne debris is present or after prolonged operation whilst cutting tall dry grass Replace the spark plug MOWER MAINTENANCE To prevent accidents stop the engine and disconnect the spark plug lead before attempting to carry out maintenance procedures on the mower 1 Engine Cowl 2 Spark Plug Lead 3 Carburetor 4 Exhaust Guard 5 Exhaust 6 Oil fill Dipstick 7 Start Grip 8 Fuel Cap 9 Finger Guard 10 Air Cleaner Sa Loosen casing clamp screw 1 and move the governor lever 2 in the direction of screw 1 as far as posible Move the throttle control to the choke position Tighten casing clamp screw Should only be made by an authorised Briggs amp Stratton dealer Under no circumstances should the engine be adjusted to run at a speed in excess of that shown on the Declaration of Conformity 1 21 MOWER MAINTENANCE 1 22 Check the oil level daily before starting the engine and ensure that the correct oil level is maintained Refer to Before Starting the Mower for oil checking and filling instructions Change the engine oil after the first 5 hours of operation and t
28. nd remove all objects which when contacted by the mower cutterblade could become dangerous projectiles Inspect the area for hidden obstruc tions which when contacted by the cutterblade could risk health and safety Remember the location of these obstructions and ensure that you mow around them 1 16 Raise the rear deflector and lift the grassbag through the handlebar and lower the rear deflector to rest against the rear of the mower To empty the grassbag pour out the grass clippings and shake the grassbag vigorously to clean the airways Good grass collection depends on good air flow through the grassbag When collecting grass clippings it is important that the grassbag is emptied regularly to pre vent blockages and engine overloading OPERATING THE MOWER Without Grass Collection Remove the grassbag and operate the mower with the rear deflector in the closed position Areas of heavy growth should be mown without collecting the clip pings If collection is required first mow the area without the grass bag at the maximum height of cut setting Allow the grass clippings to dry out and then mow the area at the maximum height of cut setting with the grassbag fitted Reduce the height of cut and mow the area again as necessary until the required finish is obtained To prevent grass damage do not remove more than one third of grass height in one cut The cutterblade is driven by the engine
29. ne to cool for at least two min utes before refuelling Do not smoke while refueling Do not attempt to start the engine if petrol is spilled or a smell of petrol is present Move the mower away from the area of spillage and avoid creating any source of ignition until petrol vapours have dissipated SAFETY PRECAUTIONS Always use fresh fuel Stale fuel can block the carburettor and cause leakage Replace fuel tank and oil tank caps securely A damaged cutterblade or loose fixing bolt are major hazards Before use always visually inspect the cutting mechanism to ensure that it is in good condition A damaged cutterblade must be replaced immedi ately with a genuine Hayter replacement part Do not operate the engine in a confined space where exhaust fumes carbon monoxide can collect Refuel outdoors only and do not smoke while refuelling Always pull the starter cord slowly until resistance is felt Then pull the cord rapidly to avoid kickback and prevent hand or arm injury Mow only in daylight or good artificial light Avoid using the mower on wet grass where feasible Always be sure of your footing on slopes Walk never run Mow across the face of slopes never up and down Exercise extreme caution when changing direction on slopes Do not mow excessively steep slopes of more than 20 degrees Use extreme caution when reversing or pulling the mower towards you Stop the engine before moving the
30. t of balance will vibrate excessively and may break DO NOT use an unbalanced cutterblade Regularly check that the bolt securing the cutterblade is tightened to the specified torque of 54Nm Replace the cutterblade every 2 years of sooner if excessively worn or damaged To prevent injury it is wise to seek assistance when turning the mower on its side 1 25 MOWER MAINTENANCE Assemble the cutterblade with the turned up edges facing towards the engine Secure the cutterblade using the bolt 1 spring washer 2 and A slightly worn cutterblade may be re sharpened Both blade edges must be sharpened equally to ensure balance Sharpen the cutterblade every 25 mowing hours or more frequently if conditions require Remove the cutterblade from the mower and clean using a brush and water Inspect the cutterblade for signs of damage Sharpen both cutting edges with a flat file to restore performance Ensure that the cutterblade is balanced Use a screw driver with a round shaft to support the cutterblade through its centre hole Hold the cutterblade horizontal and then release A balanced cutterblade will remain horizontal If the cutterblade is not balanced the heavy end will rotate downwards Sharpen the heavy end until the cutterblade is correctly balanced MOWER MAINTENANCE To store the handlebar unscrew the 2 small securing knobs sufficient ly to allow it to be pivoted forwards to rest a
31. t the following items have been supplied correctly If any items are missing contact your local Hayter dealer 1 Engine Handbook 2 Grassbag 3 Charger 341A 4 Ignition Key 341A To prevent accidents cut off the long ribbon attached to the grass bag and discard 341A Only Note Prior to first use please fully charge the battery for 14 hours Refer to battery charging Unscrew the handlebar securing knobs sufficiently to allow the handle bar to pivot Hold the engine stop lever in towards the handlebar and unfold the handlebar to the operating position before releasing Tighten both handlebar knobs to secure in position Take care to ensure that the control cables do not become snagged at the pivot point Grassbag Attachment Raise the rear deflector lower the grassbag through the handlebar and OY hook in position Lower the deflector to rest on the grassbag 1 12 C JEN THE MOER To prevent engine damage the engine is shipped without oil or petrol The engine must be filled with the correct grade of oil and petrol before starting the engine Always use high quality detergent oil classified SAE 30 oil Never use additives with recommended oil To prolong the life of your engine it is important that the oil is changed after the first 5 hours of use refer to Maintenance Schedule Clean around the oil filler cap before removing With the
32. yter co uk or contact contact Freephone 0800 616298 1 7 SAFETY PRECAUTIONS J This safety alert symbol indicates important safety messages When you see this symbol be alert to the possibility of injury Carefully read the following and inform others Your mower is perfectly safe if used correctly Failure to observe the following precautions may result in serious injury Before using the mower read the owners handbook carefully Pay par ticular attention to the safety precautions Ensure that you are familiar with the controls and the proper use of the equipment Learn how to stop the mower quickly in an emergency Never allow children or people unfamiliar with these instructions to use the mower Never mow while people especially children or pets are nearby Keep in mind that the user is responsible for accidents or hazards occurring to other people or their property D J While mowing always wear substantial footwear and long trousers Do not operate the equipment when barefoot or wearing sandals Thoroughly inspect the area where the mower is to be used and remove all objects which may be thrown by the machine WARNING Petrol is highly flammable Store fuel in containers specifically designed for this purpose Before starting the engine add fuel outdoors only Never remove the cap from the fuel tank or add petrol while the engine is running or when the engine is hot Allow the engi
Download Pdf Manuals
Related Search