Hans Grohe 32110XX1 Plumbing Product User Manual
Contents
1. Talis S 32110XX1 32112XX1 U e Talis S 32111XX1 32113XX1 ansgrone Talis S 32110XX1 32112XX1 2 Talis S 32111XX1 32113XX1 45 8 14 Technical Information Recommended water pressure Max water pressure Max hot water temp Recommended hot water temp Flow rate Battery 32210 32212 only Automatic shutoff Da 5 i AA gt un AV pl x E TEN 17 s 1134 2 15 72 psi 116 psi 176 F 120 F 140 F 1 6 gpm CR P2 6 V Lithium after 1 min Please know and follow all local plumbing codes when setting the temperature on the water heater In Massachusetts the water heater may be set no higher than 112 F 2 Installation notes Flush the hot and cold supplies thoroughly before installing the faucet Damage to the faucet caused by debris is not covered under the warranty e The hot and cold supplies should be of equal pressure e The faucet should not be used with a con tinuous flow water heater e Do not install the faucet on a sink with a raised edge e Strong light sources should not shine directly on the sensor window of the faucet e The faucet should only be used with the battery pack or power pack supplied by Hansgrohe Do not attempt to use any other battery pack or power pack Models 32211 32213 require a 110 V electri2. and shower foams can also cause damage so rinse with clean water after using Please note if the surface is already damaged the effect of cleaning materials will cause further damage Components with damaged surfaces must be replaced or injury could result Damage caused by improper treatment is not covered under the warranty Limited Lifetime Consumer Warranty This product has been manvfactured and tested to the highest quality standards by Hansgrohe Inc Hansgrohe This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1 1996 and installed in either the United States or Canada WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only This warranty is non transferable WHAT IS COVERED BY THE WARRANTY This warranty covers only your Hansgrohe manvfactured product Hansgrohe warrants this product against defects in material or workmanship as follows Hansgrohe will repair at no charge for parts only or at its option replace any product or part of the product that proves defective because of improper workmanship and or material under normal installation use service and maintenance If Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made Hansgrohe may elect to refund the purchase price in exchange for the return of the product LENGTH OF WARRANTY Replacement or repaired parts of products w
3. cal outlet installed by a licensed electrician All applicable local codes must be followed e The faucet incorporates automatic range adjustment the sensor automatically adjusts itself to local conditions lavatory brightness etc The distance between the switch on off point to the faucet is approx 6 1 4 8 under normal conditions The detection area may be less for dark non reflective objects or greater for bright highly reflec tive objects If the sink is very small or highly reflective follow the range reduc tion instructions on page 12 When the faucet is in reduced range mode the LED in the sensor window will flash while the faucet is not in use Drops of water or condensation on the sen sor window may cause the faucet to run If the LED in the sensor window flashes while the faucet is in use the battery is low but the faucet may still be used If the LED stays on the faucet will not run and the battery must be changed If the power to the outlet or to the building fails the 110 V version of the faucet will not run The spray pattern will be unattractive im mediately after installation or service due to air in the faucet After the faucet is used 10 15 times the spray pattern will clear Installation Position the faucet on the sink or countertop 1 Install and tighten the mounting nut 2 Tighten the tensioning screws 3 Connect the 3 8 adapters to the stops 4 Connect the hos
4. ected materials and products or related products not manvfactured by Hansgrohe TO OBTAIN WARRANTY PARTS OR INFORMATION Contact your Hansgrohe retailer or contact Technical Service at Hansgrohe Inc 1492 Bluegrass Lakes Parkway Alpharetta GA 30004 Tollfree 800 334 0455 In requesting warranty service you will need to provide 1 The sales receipt or other evidence of the date and place of purchase 2 A description of the problem 3 Delivery of the product or the defective part postage prepaid and carefully packed and insured to Hansgrohe Inc 1492 Bluegrass Lakes Parkway Alpharetta Georgia 30004 Attention Technical Service if required by Hansgrohe When warranty service is completed any repaired or replacement product or part will be returned to you postage prepaid EXCLUSIONS AND LIMITATIONS REPAIR OR REPLACEMENT OR IN LIMITED CIRCUMSTANCES REFUND OF THE PURCHASE PRICE AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL SPECIAL OR CONSE QUENTIAL DAMAGES ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY INCLUDING MERCHANTABILITY Some States do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclu sion may not apply to yo
5. ensor is set for maximum range at the factory If the faucet is used on a very small or highly reflective lavatory the sensor range may be reduced by ap proximately 2 Disconnect the power cable for approximately 10 seconds 1 Reconnect the power cable 2 The LED will blink once to indicate that it is in the maximum range mode When the LED stays on cover the sensor window with your hand or with a white card for 20 40 seconds to reset the electronics If the card or hand is removed in less than 20 seconds or after 40 seconds the sensor mode will not reset When the hand or card is removed the LED will blink once for maximum range twice for reduced range The LED will then stay on while the sensor recalibrates itself When the LED turns off the faucet is ready for use Replacement Parts OONAAKRWN 6 8 s aerator fixing set AC adapter battery lithium battery box connection hose electronics check valve aerator service key 98802XXO 13961000 CR P2 6V 98801000 98809000 98803000 96456000 98808000 XX color 00 chrome 82 brushed nickel Maintenance note the check valves item 8 should be removed and checked yearly 13 Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets kitchen faucets and showers consist of very different materials to comply with the needs of the market w
6. es to the adapters 5 Tighten the hoses with two wrenches as shown to prevent the hoses from twisting Connect the faucet power cable to the battery pack or AC power pack 1 Plug the AC power pack in Turn the hot and cold supplies on 2 Remove the protective film from the sensor window 3 Wait 30 seconds before attempting to use the faucet 4 Position your hand in front of the sensor to turn the water on Due to air in the faucet the spray pattern may be unattractive for the first 10 15 uses after installation or service 32110XX1 32112XX1 only pull the temperature lever forward to make the water cooler backward to make it warmer Temperature adjustment 32111XX1 32113XX1 only Turn the water supplies off 1 Disconnect the faucet power cable from the battery pack or AC power pack 2 Remove the screw from the rear of the faucet 3 Remove the faucet body 1 Turn the temperature screw forward to make the water cooler backward to make it warmer 2 Dry any drops of water from the faucet or mounting surface Replace the faucet body 1 Replace the screw 2 Turn the water supplies on 3 Reconnect the power cable 4 Wait 30 seconds 1 Place your hand in front of the faucet to turn it on 2 Battery replacement models 32110XX1 32111XX1 only If the LED in the sensor window flashes the batter
7. ill be covered for the term of this warranty as stated in the following two sentenc es If you are a consumer who purchased the product for use primarily for personal family or household purposes this war ranty extends for as long as you own the product and the home in which the product is originally installed If you purchased 14 the product for use primarily for any other purpose including without limitation a commercial purpose this warranty extends only i for 1 year with respect to Hansgrohe and Commercial products and ii for 5 years with respect to AXOR products THIS WARRANTY DOES NOT COVER AND HANSGROHE WILL NOT PAY FOR A Conditions malfunctions or damage not resulting from defects in material or workmanship B Conditions malfunctions or damage resulting from 1 normal wear and tear improper installation improper mainte nance misuse abuse negligence accident or alteration or 2 the use of abrasive or caustic cleaning agents or no rinse cleaning products or the use of the product in any manner contrary to the product instructions 3 Conditions in the home such as excessive water pressure or corrosion C Labor or other expenses for the disconnection deinstallation or return of the product for warranty service or for installa tion or reinstallation of the product including but not limited to proper packaging and shipping costs or for installation or reinstallation of the product D Accessories conn
8. ith regard to design and functionality To avoid damage and returns it is necessary to consider certain criteria when cleaning Cleaning Materials for Faucets and Showers Acids are a necessary ingredient of cleaning materials for removing lime however please pay attention to the following points when cleaning faucets and showers e Only use cleaning materials which are explicitly intended for this type of application e Never use cleaning materials which contain hydrochloric formic phosphoric or acetic acid as they cause considerable damage e Never mix one cleaning material with another Never use cleaning materials or appliances with an abrasive effect such as unsuitable cleaning powders sponge pads or micro fiber cloths Cleaning Instructions for Faucets and Showers Please follow the cleaning material manufacturer s instructions In addition pay attention to the following points e Clean the faucets and showers as and when required Use the amount of cleaning product and the amount of time recommended by the manufacturer Do not leave the cleaner on the fixture longer than necessary e Regular cleaning can prevent calcification e When using spray cleaners spray first onto a soft cloth or sponge Never spray directly onto the faucet as droplets can enter openings and gaps and cause damage e After cleaning rinse thoroughly with clean water to remove any cleaner residue Important Residues of liquid soaps shampoos
9. u This warranty gives you specific legal rights and you may have other rights which vary from State to State You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court against us under the Magnuson Moss Warranty Act PRODUCT INSTRUCTIONS AND QUESTIONS Upon purchase or prior to installation please carefully inspect your Hansgrohe product for any damage or visible defect Prior to installing always carefully study the enclosed instructions on the proper installation and the care and maintenance of the product If you have questions at any time about the use installation or performance of your Hansgrohe product or this warranty please call or write to us or call us toll free at 800 334 0455 ansgrone Hansgrohe Inc e 1490 Bluegrass Lakes Parkway Alpharetta GA 30004 Tel 770 360 9880 Fax 770 360 9887 www hansgrohe usa com US Installation Instructions e Part No 90423121 e Revised 11 2007
10. y is low but the faucet can still be used If the LED lights continuously the battery must be changed before the faucet can be used Remove the four screws and the battery pack cover Remove the old battery 1 Install the new battery 2 Lithium CR P2 6V Reinstall the battery pack cover Wait 30 seconds 1 Activate the faucet by placing a hand in front of the sensor 2 Clean the aerator and filters all models If the water flow is reduced over time clean the aerator a and the filters b Turn the water supplies off 1 Disconnect the power cable 2 Unscrew the aerator a with the service key Disconnect the hot and cold supply hoses from the adapters Remove the filters b At another sink rinse the filters and the aerator Reinstall the aerator Replace the filters Reconnect the hot and cold supply hoses see page 4 Turn the water on 1 Reconnect the power cable 2 Wait 30 seconds 1 Place a hand in front of the sensor to turn the faucet on 2 Cleaning The faucet may be turned off temporarily so that the sink may be cleaned Cover the sensor window with a hand for approximately 10 seconds The faucet will turn off for approximately 60 seconds so that the sink may be cleaned The LED in the sensor window will flash When the LED no longer flashes the faucet may be used normally Reduce the sensor range The s
Download Pdf Manuals
Related Search