HandHeld Entertainment 4800dr eBook Reader User Manual
Contents
1. Quick Start Guide Document Reader Note Refer to your Barcode Manual for information about cleaning your device For localized language versions of this document go to www handheld com Assembling the 4800dr Place arm on tray Use the 3 screws provided to attach the arm to the underside of the tray Place the imager in the stand Press the cable firmly into the wire run along the back of the arm You must use the USB cable that s supplied with the 4800dr or a compatible 5 volt powered cable Imager Mounting Details If you are planning to mount the imager in a fixed position the following diagram shows the mounting hole placement and details All measurements are in inches ASSEMBLE TRI STAR INDUSTRIES C SERIES CHEVRON THREADED INSERTS 4 40 X 170 FLUSH TO 010 BELOW SURFACE 3 PLACES DEPTH FROM OUTSIDE OF 3 BOSS SURFACES TO BOTTOM OF BOSSES EQUALS 25 1 566 REF 422 REF 842 REF Connecting to the Host Turn off computer s power before connecting the document reader then power up the computer once the document reader is fully connected USB Connection TTL 232 Connection Interface Scan the barcode that describes the PC or interface you are using USB Keyboard PC USB Keyboard Mac USB Japan2. HE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU All provisions of this Limited Warranty are separate and severable which means that if any provision is held invalid and unenforceable such determination shall not affect the validity of enforceability of the other provisions hereof Use of any peripherals not manufactured sold by Hand Held Products voids the warranty This includes but is not limited to cables power supplies cradles and docking stations Hand Held Products Inc extends these warranties only to the first end users of the products These warranties are nontransferable The limited duration of the warranty for the 4800dr is for 3 three years Disclaimer Hand Held Products Inc Hand Held Products reserves the right to make changes in specifications and other information contained in this document without prior notice and the reader should in all cases consult Hand Held Products to determine whether any such changes have been made The information in this publication does not represent a commitment on the part of Hand Held Products Hand Held Products shall not be liable for technical or editorial errors or omissions contained herein nor for incidental or consequential damages resulting from the furnishing performance or use of this material This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or tra
3. echsupport handheld com Online Technical Assistance You can also access technical assistance online at www handheld com For Further Information To download the full User s Guide for these products visit our website at www handheld com Product Service and Repair Hand Held Products provides service for all its products through service centers throughout the world To obtain warranty or non warranty service return the unit to Hand Held Products postage paid with a copy of the dated purchase record attached Contact the appropriate location below to obtain a Return Material Authorization number RMA before returning the product North America Telephone 800 782 4263 Fax 803 835 8012 E mail naservice handheld com Latin America Telephone 803 835 8000 Telephone 800 782 4263 Fax 239 263 9689 E mail laservice handheld com Brazil Telephone 55 21 3535 9100 Fax 55 21 3535 9105 E mail brservice handheld com Mexico Telephone 52 55 5203 2100 Fax 52 55 5531 3672 E mail mxservice handheld com Europe Middle East and Africa Telephone 31 0 40 2901 633 Fax 31 0 40 2901 631 E mail euservice handheld com Asia Pacific Telephone 852 2511 3050 Fax 852 2511 3557 E mail apservice handheld com Japan Telephone 813 5770 6312 Fax 813 5770 6313 E mail apservice handheld com Online Product Service and Repair Assistance You can also access product service and
4. ese Keyboard PC USB HID Barcode Reader SB COM Port Emulation TTL 232 Interface Aligning the Document Reader Tray Proper cable placement is important for accurate alignment ofthe device Place the cable in the wire channel if the imager will remain in the base most of the time If you plan to frequently lift out the imager to scan items then set the cable in the location where it will rest while the imager is in the stand Note The 4800dr will not capture any images until it has been properly aligned using the following procedure 1 Loosen the screw in the base tray with a coin 2 Place the alignment page on the tray Align the upper left corner of the alignment page to the upper left corner of the tray 3 Make sure the serial number on the alignment page the top number matches the serial number on your document reader ie 4800dr s n 07150A181D engine s n 07267A1C30 4 Press the button on the imager to display the illuminated aimer crosshairs You will hear a single beep that indicates you are using the correct page If you hear 3 beeps and the aimer turns off then you have the wrong alignment page for your document reader 5 Move the tray until the illuminated aimer crosshairs line up with the printed crosshairs on the alignment page Be sure to wait until the crosshairs go off before removing power or a
5. nslated into another language without the prior written consent of Hand Held Products 2006 Hand Held Products Inc All rights reserved Web Address www handheld com 10 Hand Held Products Inc 700 Visions Drive P O Box 208 Skaneateles Falls NY 13153 0208 4800dr QS Rev A 12 07
6. repair assistance online at www handheld com Limited Warranty Hand Held Products Inc Hand Held Products warrants its products to be free from defects in materials and workmanship and to conform to Hand Held Products published specifications applicable to the products purchased at the time of shipment This warranty does not cover any Hand Held Products product which is i improperly installed or used ii damaged by accident or negligence including failure to follow the proper maintenance service and cleaning schedule or iii damaged as a result of A modification or alteration by the purchaser or other party B excessive voltage or current supplied to or drawn from the interface connections C static electricity or electro static discharge D operation under conditions beyond the specified operating parameters or E repair or service of the product by anyone other than Hand Held Products or its authorized representatives This warranty shall extend from the time of shipment for the duration published by Hand Held Products for the product at the time of purchase Warranty Period Any defective product must be returned at purchaser s expense during the Warranty Period to Hand Held Products factory or authorized service center for inspection No product will be accepted by Hand Held Products without a Return Materials Authorization which may be obtained by contacting Hand Held Products In the event that the product is retu
7. rned to Hand Held Products or its authorized service center within the Warranty Period and Hand Held Products determines to its satisfaction that the product is defective due to defects in materials or workmanship Hand Held Products at its sole option will either repair or replace the product without charge except for return shipping to Hand Held Products EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR WARRANTIES EITHER EXPRESSED OR IMPLIED ORAL OR WRITTEN INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE HAND HELD PRODUCTS RESPONSIBILITY AND PURCHASER S EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT IN NO EVENT SHALL HAND HELD PRODUCTS BE LIABLE FOR INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES AND IN NO EVENT SHALL ANY LIABILITY OF HAND HELD PRODUCTS ARISING IN CONNECTION WITH ANY PRODUCT SOLD HEREUNDER WHETHER SUCH LIABILITY ARISES FROM A CLAIM BASED ON CONTRACT WARRANTY TORT OR OTHERWISE EXCEED THE ACTUAL AMOUNT PAID TO HAND HELD PRODUCTS FOR THE PRODUCT THESE LIMITATIONS ON LIABILITY SHALL REMAIN IN FULL FORCE AND EFFECT EVEN WHEN HAND HELD PRODUCTS MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES LOSSES OR DAMAGES SOME STATES PROVINCES OR COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO T
8. ttempting to capture an image 6 Remove the alignment page and tighten the screw Save the alignment page in the event that the tray needs to be realigned in the future Note Ifyou need to print anew copy of the alignment page make sure to print the page in landscape mode Imaging Technique Center a document in the document reader tray Smaller documents should be centered in the pocket in the tray Press the button on the imager The view finder projects an aiming beam to indicate the image capture area Technical Assistance If you need assistance installing or troubleshooting please call your Distributor or the nearest Hand Held Products technical support office North America Canada Telephone 800 782 4263 Fax number 315 554 6705 E mail natechsupport handheld com Latin America Telephone 803 835 8000 Telephone 800 782 4263 E mail latechsupport handheld com Brazil Telephone 55 21 3535 9100 Fax 55 21 3535 9105 E mail brsuporte handheld com Mexico Telephone 803 835 8000 E mail latechsupport handheld com Europe Middle East and Africa Telephone 31 0 40 7999 393 Fax 31 0 40 2425 672 E mail eurosupport handheld com Asia Pacific Telephone Hong Kong 852 3188 3485 or 2511 3050 Telephone China 86 21 6361 3818 E mail aptechsupport handheld com Japan Telephone 813 5770 6312 E mail aptechsupport handheld com Malaysia Telephone 603 6201 7020 E mail apt
Download Pdf Manuals
Related Search